Chapter 4 Network Layer Computer Networking: A Top Down Approach 6 th edition Jim Kurose, Keith Ross Addison-Wesley March 2012 A note on the use of these ppt slides: We’re making these slides freely available to all (faculty, students, readers). They’re in PowerPoint form so you see the animations; and can add, modify, and delete slides (including this one) and slide content to suit your needs. They obviously represent a lot of work on our part. In return for use, we only ask the following: If you use these slides (e.g., in a class) that you mention their source (after all, we’d like people to use our book!) If you post any slides on a www site, that you note that they are adapted from (or perhaps identical to) our slides, and note our copyright of this material. Thanks and enjoy! JFK/KWR All material copyright 1996-2012 J.F Kurose and K.W. Ross, All Rights Reserved Network Layer 4-1
155
Embed
Chapter 4 Network Layer Computer Networking: A Top Down Approach 6 th edition Jim Kurose, Keith Ross Addison-Wesley March 2012 A note on the use of these.
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Chapter 4Network Layer
Computer Networking: A Top Down Approach 6th edition Jim Kurose, Keith RossAddison-WesleyMarch 2012
A note on the use of these ppt slides:We’re making these slides freely available to all (faculty, students, readers). They’re in PowerPoint form so you see the animations; and can add, modify, and delete slides (including this one) and slide content to suit your needs. They obviously represent a lot of work on our part. In return for use, we only ask the following: If you use these slides (e.g., in a class) that you mention their source
(after all, we’d like people to use our book!) If you post any slides on a www site, that you note that they are adapted
from (or perhaps identical to) our slides, and note our copyright of this material.
Thanks and enjoy! JFK/KWR
All material copyright 1996-2012 J.F Kurose and K.W. Ross, All Rights Reserved
Q: but what happens if ranges don’t divide up so nicely?
Datagram forwarding table
Network Layer 4-19
Longest prefix matching
Destination Address Range
11001000 00010111 00010*** *********
11001000 00010111 00011000 *********
11001000 00010111 00011*** *********
otherwise
DA: 11001000 00010111 00011000 10101010
examples:DA: 11001000 00010111 00010110 10100001 which interface?
which interface?
when looking for forwarding table entry for given destination address, use longest address prefix that matches destination address.
longest prefix matching
Link interface
0
1
2
3
Network Layer 4-20
Datagram or VC network: why?
Internet (datagram) data exchange among
computers “elastic” service, no strict
timing req. many link types
different characteristics uniform service difficult
“smart” end systems (computers) can adapt, perform
control, error recovery simple inside
network, complexity at “edge”
ATM (VC) evolved from
telephony human conversation:
strict timing, reliability requirements
need for guaranteed service
“dumb” end systems telephones complexity inside
network
Network Layer 4-21
4.1 introduction4.2 virtual circuit and
datagram networks4.3 what’s inside a
router4.4 IP: Internet Protocol
datagram format IPv4 addressing ICMP IPv6
4.5 routing algorithms link state distance vector hierarchical routing
4.6 routing in the Internet RIP OSPF BGP
4.7 broadcast and multicast routing
Chapter 4: outline
Network Layer 4-22
Router architecture overviewtwo key router functions: run routing algorithms/protocol (RIP, OSPF, BGP) forwarding datagrams from incoming to outgoing link
high-seed switching
fabric
routing processor
router input ports router output ports
forwarding data plane (hardware)
routing, managementcontrol plane (software)
forwarding tables computed,pushed to input ports
Network Layer 4-23
linetermination
link layer
protocol(receive)
lookup,forwarding
queueing
Input port functions
decentralized switching: given datagram dest., lookup output
port using forwarding table in input port memory
goal: complete input port processing at ‘line speed’
queuing: if datagrams arrive faster than forwarding rate into switch fabric
physical layer:bit-level reception
data link layer:e.g., Ethernetsee chapter 5
switchfabric
Network Layer 4-24
Switching fabrics transfer packet from input buffer to
appropriate output buffer switching rate: rate at which packets
can be transferred from inputs to outputs often measured as multiple of input/output line rate N inputs: switching rate N times line rate desirable
three types of switching fabrics
memory
memory
bus crossbar
Network Layer 4-25
Switching via memoryfirst generation routers: traditional computers with switching under direct control
of CPU packet copied to system’s memory CPU extracts dest address from packet’s header, looks up
output port in forwarding table, copies to output port speed limited by memory bandwidth (2 bus crossings per
datagram) one packet at a time
inputport
(e.g.,Ethernet)
memory
outputport
(e.g.,Ethernet)
system bus
Network Layer 4-26
Switching via a bus
datagram from input port memory
to output port memory via a shared bus
bus contention: switching speed limited by bus bandwidth
one packet a time 32 Gbps bus, Cisco 5600:
sufficient speed for access and enterprise routers
bus
Network Layer 4-27
Switching via interconnection network forwards multiple packets in
parallel banyan networks, crossbar, other
interconnection nets initially developed to connect processors in multiprocessor
When packet from port A needs to forwarded to port Y, controller closes cross point at intersection of two buses
advanced design: fragmenting datagram into fixed length cells, switch cells through the fabric.
crossbar
A
B
C
X Y Z
Network Layer 4-28
Output ports
buffering required when datagrams arrive from fabric faster than the transmission rate
scheduling discipline chooses among queued datagrams for transmission
linetermination
link layer
protocol(send)
switchfabric
datagrambuffer
queueing
Network Layer 4-29
Output port queueing
suppose Rswitch is N times faster than Rline still have output buffering when multiple inputs send to same
output queueing (delay) and loss due to output port buffer overflow!
at t, packets morefrom input to output
one packet time later
switchfabric
switchfabric
Network Layer 4-30
How much buffering?
RFC 3439 rule of thumb: average buffering equal to “typical” RTT (say 250 msec) times link capacity C e.g., C = 10 Gpbs link: 2.5 Gbit buffer
recent recommendation: with N flows, buffering equal to
RTT C.N
Network Layer 4-31
Input port queuing fabric slower than input ports combined
queuing may occur at input queues queuing delay and loss due to input buffer
overflow! Head-of-the-Line (HOL) blocking: queued
datagram at front of queue prevents others in queue from moving forward
output port contention:only one red datagram can
be transferred.lower red packet is blocked
switchfabric
one packet time later: green
packet experiences HOL
blocking
switchfabric
Network Layer 4-32
4.1 introduction4.2 virtual circuit and
datagram networks4.3 what’s inside a
router4.4 IP: Internet Protocol
datagram format IPv4 addressing ICMP IPv6
4.5 routing algorithms link state distance vector hierarchical routing
4.6 routing in the Internet RIP OSPF BGP
4.7 broadcast and multicast routing
Chapter 4: outline
Network Layer 4-33
The Internet network layer
forwardingtable
host, router network layer functions:
routing protocols• path selection• RIP, OSPF, BGP
IP protocol• addressing conventions• datagram format• packet handling conventions
“Send me anythingwith addresses beginning 200.23.16.0/20”
200.23.16.0/23
200.23.18.0/23
200.23.30.0/23
Fly-By-Night-ISP
Organization 0
Organization 7Internet
Organization 1
ISPs-R-Us“Send me anythingwith addresses beginning 199.31.0.0/16”
200.23.20.0/23Organization 2
...
...
hierarchical addressing allows efficient advertisement of routing information:
Network Layer 4-46
ISPs-R-Us has a more specific route to Organization 1
“Send me anythingwith addresses beginning 200.23.16.0/20”
200.23.16.0/23
200.23.18.0/23
200.23.30.0/23
Fly-By-Night-ISP
Organization 0
Organization 7Internet
Organization 1
ISPs-R-Us“Send me anythingwith addresses beginning 199.31.0.0/16or 200.23.18.0/23”
200.23.20.0/23Organization 2
...
...
Hierarchical addressing: more specific routes
Network Layer 4-47
IP addressing: how to get a block?
Q: how does an ISP get block of addresses?
A: ICANN: Internet Corporation for Assigned
Names and Numbers http://www.icann.org/ allocates addresses manages DNS assigns domain names, resolves
disputes
Network Layer 4-48
IP addresses: how to get one?Q: How does a host get IP address?
hard-coded by system admin in a file Windows: control-panel->network->configuration-
>tcp/ip->properties UNIX: /etc/rc.config
DHCP: Dynamic Host Configuration Protocol: dynamically get address from as server “plug-and-play”
Network Layer 4-49
DHCP: Dynamic Host Configuration Protocol
goal: allow host to dynamically obtain its IP address from network server when it joins network can renew its lease on address in use allows reuse of addresses (only hold address while
connected/“on”) support for mobile users who want to join network (more shortly)
DHCP overview: host broadcasts “DHCP discover” msg [optional] DHCP server responds with “DHCP offer” msg [optional] host requests IP address: “DHCP request” msg DHCP server sends address: “DHCP ack” msg
IP address address of first-hop router for client name and IP address of DNS sever network mask (indicating network versus
host portion of address)
Network Layer 4-53
connecting laptop needs its IP address, addr of first-hop router, addr of DNS server: use DHCP
router with DHCP server built into router
DHCP request encapsulated in UDP, encapsulated in IP, encapsulated in 802.3 Ethernet Ethernet frame broadcast (dest: FFFFFFFFFFFF) on LAN, received at router running DHCP server Ethernet demuxed to IP demuxed, UDP demuxed to DHCP
168.1.1.1
DHCPUDP
IPEthPhy
DHCP
DHCP
DHCP
DHCP
DHCP
DHCPUDP
IPEthPhy
DHCP
DHCP
DHCP
DHCPDHCP
DHCP: example
Network Layer 4-54
DCP server formulates DHCP ACK containing client’s IP address, IP address of first-hop router for client, name & IP address of DNS server
encapsulation of DHCP server, frame forwarded to client, demuxing up to DHCP at client
DHCP: example
router with DHCP server built into router
DHCP
DHCP
DHCP
DHCP
DHCPUDP
IPEthPhy
DHCP
DHCPUDP
IPEthPhy
DHCP
DHCP
DHCP
DHCP
client now knows its IP address, name and IP address of DSN server, IP address of its first-hop router
Network Layer 4-55
DHCP: Wireshark output (home LAN)
Message type: Boot Reply (2)Hardware type: EthernetHardware address length: 6Hops: 0Transaction ID: 0x6b3a11b7Seconds elapsed: 0Bootp flags: 0x0000 (Unicast)Client IP address: 192.168.1.101 (192.168.1.101)Your (client) IP address: 0.0.0.0 (0.0.0.0)Next server IP address: 192.168.1.1 (192.168.1.1)Relay agent IP address: 0.0.0.0 (0.0.0.0)Client MAC address: Wistron_23:68:8a (00:16:d3:23:68:8a)Server host name not givenBoot file name not givenMagic cookie: (OK)Option: (t=53,l=1) DHCP Message Type = DHCP ACKOption: (t=54,l=4) Server Identifier = 192.168.1.1Option: (t=1,l=4) Subnet Mask = 255.255.255.0Option: (t=3,l=4) Router = 192.168.1.1Option: (6) Domain Name Server Length: 12; Value: 445747E2445749F244574092; IP Address: 68.87.71.226; IP Address: 68.87.73.242; IP Address: 68.87.64.146Option: (t=15,l=20) Domain Name = "hsd1.ma.comcast.net."
reply
Message type: Boot Request (1)Hardware type: EthernetHardware address length: 6Hops: 0Transaction ID: 0x6b3a11b7Seconds elapsed: 0Bootp flags: 0x0000 (Unicast)Client IP address: 0.0.0.0 (0.0.0.0)Your (client) IP address: 0.0.0.0 (0.0.0.0)Next server IP address: 0.0.0.0 (0.0.0.0)Relay agent IP address: 0.0.0.0 (0.0.0.0)Client MAC address: Wistron_23:68:8a (00:16:d3:23:68:8a)Server host name not givenBoot file name not givenMagic cookie: (OK)Option: (t=53,l=1) DHCP Message Type = DHCP RequestOption: (61) Client identifier Length: 7; Value: 010016D323688A; Hardware type: Ethernet Client MAC address: Wistron_23:68:8a (00:16:d3:23:68:8a)Option: (t=50,l=4) Requested IP Address = 192.168.1.101Option: (t=12,l=5) Host Name = "nomad"Option: (55) Parameter Request List Length: 11; Value: 010F03062C2E2F1F21F92B 1 = Subnet Mask; 15 = Domain Name 3 = Router; 6 = Domain Name Server 44 = NetBIOS over TCP/IP Name Server ……
request
Network Layer 4-56
NAT: network address translation
10.0.0.1
10.0.0.2
10.0.0.3
10.0.0.4
138.76.29.7
local network(e.g., home network)
10.0.0/24
rest ofInternet
datagrams with source or destination in this networkhave 10.0.0/24 address for source, destination (as usual)
all datagrams leaving local
network have same single source NAT IP
address: 138.76.29.7,different source port numbers
Network Layer 4-57
motivation: local network uses just one IP address as far as outside world is concerned: range of addresses not needed from ISP:
just one IP address for all devices can change addresses of devices in local
network without notifying outside world can change ISP without changing
addresses of devices in local network devices inside local net not explicitly
addressable, visible by outside world (a security plus)
NAT: network address translation
Network Layer 4-58
implementation: NAT router must:
outgoing datagrams: replace (source IP address, port #) of every outgoing datagram to (NAT IP address, new port #). . . remote clients/servers will respond using (NAT IP
address, new port #) as destination addr
remember (in NAT translation table) every (source IP address, port #) to (NAT IP address, new port #) translation pair
incoming datagrams: replace (NAT IP address, new port #) in dest fields of every incoming datagram with corresponding (source IP address, port #) stored in NAT table
NAT: network address translation
Network Layer 4-59
10.0.0.1
10.0.0.2
10.0.0.3
S: 10.0.0.1, 3345D: 128.119.40.186, 80
1
10.0.0.4
138.76.29.7
1: host 10.0.0.1 sends datagram to 128.119.40.186, 80
IPv6: motivation initial motivation: 32-bit address space
soon to be completely allocated. additional motivation:
header format helps speed processing/forwarding
header changes to facilitate QoS
IPv6 datagram format: fixed-length 40 byte header no fragmentation allowed
Network Layer 4-68
IPv6 datagram format
priority: identify priority among datagrams in flowflow Label: identify datagrams in same “flow.” (concept of“flow” not well defined).next header: identify upper layer protocol for data
data
destination address(128 bits)
source address(128 bits)
payload len next hdr hop limitflow labelpriver
32 bits
Network Layer 4-69
Other changes from IPv4
checksum: removed entirely to reduce processing time at each hop
options: allowed, but outside of header, indicated by “Next Header” field
ICMPv6: new version of ICMP additional message types, e.g. “Packet Too
Big” multicast group management functions
Network Layer 4-70
Transition from IPv4 to IPv6 not all routers can be upgraded
simultaneously no “flag days” how will network operate with mixed IPv4
and IPv6 routers? tunneling: IPv6 datagram carried as payload
in IPv4 datagram among IPv4 routers
IPv4 source, dest addr IPv4 header fields
IPv4 datagram
IPv6 datagram
IPv4 payload
UDP/TCP payload
IPv6 source dest addrIPv6 header fields
Network Layer 4-71
Tunneling
physical view:
IPv4 IPv4
A B
IPv6 IPv6
E
IPv6 IPv6
FC D
logical view:
IPv4 tunnel connecting IPv6 routers
E
IPv6 IPv6
FA B
IPv6 IPv6
Network Layer 4-72
flow: Xsrc: Adest: F
data
A-to-B:IPv6
Flow: XSrc: ADest: F
data
src:Bdest: E
B-to-C:IPv6 inside
IPv4
E-to-F:IPv6
flow: Xsrc: Adest: F
data
B-to-C:IPv6 inside
IPv4
Flow: XSrc: ADest: F
data
src:Bdest: E
physical view:A B
IPv6 IPv6
E
IPv6 IPv6
FC D
logical view:
IPv4 tunnel connecting IPv6 routers
E
IPv6 IPv6
FA B
IPv6 IPv6
Tunneling
IPv4 IPv4
Network Layer 4-73
4.1 introduction4.2 virtual circuit and
datagram networks4.3 what’s inside a
router4.4 IP: Internet Protocol
datagram format IPv4 addressing ICMP IPv6
4.5 routing algorithms link state distance vector hierarchical routing
4.6 routing in the Internet RIP OSPF BGP
4.7 broadcast and multicast routing
Chapter 4: outline
Network Layer 4-74
1
23
IP destination address in arriving packet’s header
key question: what is the least-cost path between u and z ?routing algorithm: algorithm that finds that least cost path
Network Layer 4-77
Routing algorithm classificationQ: global or decentralized
information?
global: all routers have complete
topology, link cost info “link state” algorithmsdecentralized: router knows physically-
connected neighbors, link costs to neighbors
iterative process of computation, exchange of info with neighbors
“distance vector” algorithms
Q: static or dynamic?
static: routes change slowly
over timedynamic: routes change more
quickly periodic update in response to link
cost changes
Network Layer 4-78
4.1 introduction4.2 virtual circuit and
datagram networks4.3 what’s inside a
router4.4 IP: Internet Protocol
datagram format IPv4 addressing ICMP IPv6
4.5 routing algorithms link state distance vector hierarchical routing
4.6 routing in the Internet RIP OSPF BGP
4.7 broadcast and multicast routing
Chapter 4: outline
Network Layer 4-79
A Link-State Routing AlgorithmDijkstra’s algorithm net topology, link costs
known to all nodes accomplished via “link
state broadcast” all nodes have same info
computes least cost paths from one node (‘source”) to all other nodes gives forwarding table
for that node iterative: after k
iterations, know least cost path to k destinations
notation: c(x,y): link cost from
node x to y; = ∞ if not direct neighbors
D(v): current value of cost of path from source to dest. v
p(v): predecessor node along path from source to v
N': set of nodes whose least cost path definitively known
Network Layer 4-80
Dijsktra’s Algorithm
1 Initialization: 2 N' = {u} 3 for all nodes v 4 if v adjacent to u 5 then D(v) = c(u,v) 6 else D(v) = ∞ 7 8 Loop 9 find w not in N' such that D(w) is a minimum 10 add w to N' 11 update D(v) for all v adjacent to w and not in N' : 12 D(v) = min( D(v), D(w) + c(w,v) ) 13 /* new cost to v is either old cost to v or known 14 shortest path cost to w plus cost from w to v */ 15 until all nodes in N'
Network Layer 4-81
w3
4
v
x
u
5
37 4
y
8
z2
7
9
Dijkstra’s algorithm: example
Step N'D(v)
p(v)
012345
D(w)p(w)
D(x)p(x)
D(y)p(y)
D(z)p(z)
u ∞ ∞ 7,u 3,u 5,uuw ∞ 11,w 6,w 5,u
14,x 11,w 6,wuwxuwxv 14,x 10,v
uwxvy 12,y
notes: construct shortest path
tree by tracing predecessor nodes
ties can exist (can be broken arbitrarily)
uwxvyz
6}33,7min{
)),()(),(min()( .,.
vwcwDvDvDge
Network Layer 4-82
Dijkstra’s algorithm: example
w3
4
v
x
u
5
37 4
y
8
z2
7
9
vx
y
w
z
(u,w)
(u,x)
(u,w)
(u,w)
(u,w)
destination link
resulting forwarding table in u:
Network Layer 4-83
Dijkstra’s algorithm, discussionalgorithm complexity: n nodes each iteration: need to check all nodes, w, not in N n(n+1)/2 comparisons: O(n2) more efficient implementations possible: O(nlogn)
oscillations possible: e.g., support link cost equals amount of carried
traffic:
A
D
C
B1 1+e
e0
e
1 1
0 0
initially
A
D
C
B
given these costs,find new routing….
resulting in new costs
2+e 0
001+e 1
A
D
C
B
given these costs,find new routing….
resulting in new costs
0 2+e
1+e10 0
A
D
C
B
given these costs,find new routing….
resulting in new costs
2+e 0
001+e 1
Network Layer 4-84
4.1 introduction4.2 virtual circuit and
datagram networks4.3 what’s inside a
router4.4 IP: Internet Protocol
datagram format IPv4 addressing ICMP IPv6
4.5 routing algorithms link state distance vector hierarchical routing
Distance vector: link cost changeslink cost changes: node detects local link cost
change updates routing info,
recalculates distance vector
if DV changes, notify neighbors
“goodnews travelsfast”
x z14
50
y1
t0 : y detects link-cost change, updates its DV, informs its neighbors.
t1 : z receives update from y, updates its table, computes new least cost to x , sends its neighbors its DV.
t2 : y receives z’s update, updates its distance table. y’s least costs do not change, so y does not send a message to z.
Network Layer 4-93
Distance vector: link cost changeslink cost changes: node detects local link cost
change bad news travels slow -
“count to infinity” problem! 44 iterations before
algorithm stabilizes: see text
x z14
50
y60
poisoned reverse: If Z routes through Y to get to X :
Z tells Y its (Z’s) distance to X is infinite (so Y won’t route to X via Z)
will this completely solve count to infinity problem?
Network Layer 4-94
Comparison of LS and DV algorithmsmessage complexity LS: with n nodes, E links,
O(nE) msgs sent DV: exchange between
neighbors only convergence time varies
speed of convergence LS: O(n2) algorithm
requires O(nE) msgs may have oscillations
DV: convergence time varies may be routing loops count-to-infinity problem
robustness: what happens if router malfunctions?
LS: node can advertise
incorrect link cost each node computes
only its own table
DV: DV node can advertise
incorrect path cost each node’s table used
by others • error propagate thru
network
Network Layer 4-95
4.1 introduction4.2 virtual circuit and
datagram networks4.3 what’s inside a
router4.4 IP: Internet Protocol
datagram format IPv4 addressing ICMP IPv6
4.5 routing algorithms link state distance vector hierarchical routing
4.6 routing in the Internet RIP OSPF BGP
4.7 broadcast and multicast routing
Chapter 4: outline
Network Layer 4-96
Hierarchical routing
scale: with 600 million destinations:
can’t store all dest’s in routing tables!
routing table exchange would swamp links!
administrative autonomy
internet = network of networks
each network admin may want to control routing in its own network
our routing study thus far - idealization
all routers identical network “flat”… not true in practice
Network Layer 4-97
collect routers into regions, “autonomous systems” (AS)
Each AS within an ISP ISP may consist of
one or more ASes
routers in same AS run same routing protocol “intra-AS” routing
protocol routers in different
AS can run different intra-AS routing protocol
gateway router: at “edge” of its own AS has link to router in
another AS
Hierarchical routing
Network Layer 4-98
3b
1d
3a
1c2aAS3
AS1
AS21a
2c2b
1b
Intra-ASRouting algorithm
Inter-ASRouting algorithm
Forwardingtable
3c
Interconnected ASes
forwarding table configured by both intra- and inter-AS routing algorithm intra-AS sets
entries for internal dests
inter-AS & intra-AS sets entries for external dests
Network Layer 4-99
Inter-AS tasks suppose router in
AS1 receives datagram destined outside of AS1: router should
forward packet to gateway router, but which one?
AS1 must:1. learn which dests
are reachable through AS2, which through AS3
2. propagate this reachability info to all routers in AS1
job of inter-AS routing!
AS3
AS2
3b
3c
3a
AS1
1c1a
1d1b
2a2c
2b
othernetworks
othernetworks
Network Layer 4-100
Example: setting forwarding table in router 1d
suppose AS1 learns (via inter-AS protocol) that subnet x reachable via AS3 (gateway 1c), but not via AS2 inter-AS protocol propagates reachability info to
all internal routers router 1d determines from intra-AS routing info that
its interface I is on the least cost path to 1c installs forwarding table entry (x,I)
AS3
AS2
3b
3c
3a
AS1
1c1a
1d1b
2a2c
2b
othernetworks
othernetworks
x…
Network Layer 4-101
Example: choosing among multiple ASes now suppose AS1 learns from inter-AS protocol
that subnet x is reachable from AS3 and from AS2.
to configure forwarding table, router 1d must determine towards which gateway it should forward packets for dest x this is also job of inter-AS routing protocol!
AS3
AS2
3b
3c
3a
AS1
1c1a
1d1b
2a2c
2b
othernetworks
othernetworks
x ……
…
?
Network Layer 4-102
learn from inter-AS protocol that subnet x is reachable via multiple gateways
use routing infofrom intra-AS
protocol to determinecosts of least-cost
paths to eachof the gateways
hot potato routing:choose the gateway
that has the smallest least cost
determine fromforwarding table the interface I that leads
to least-cost gateway. Enter (x,I) in
forwarding table
Example: choosing among multiple ASes now suppose AS1 learns from inter-AS protocol
that subnet x is reachable from AS3 and from AS2.
to configure forwarding table, router 1d must determine towards which gateway it should forward packets for dest x this is also job of inter-AS routing protocol!
hot potato routing: send packet towards closest of two routers.
Network Layer 4-103
4.1 introduction4.2 virtual circuit and
datagram networks4.3 what’s inside a
router4.4 IP: Internet Protocol
datagram format IPv4 addressing ICMP IPv6
4.5 routing algorithms link state distance vector hierarchical routing
4.6 routing in the Internet RIP OSPF BGP
4.7 broadcast and multicast routing
Chapter 4: outline
Network Layer 4-104
Intra-AS Routing
also known as interior gateway protocols (IGP)
most common intra-AS routing protocols: RIP: Routing Information Protocol OSPF: Open Shortest Path First IGRP: Interior Gateway Routing
Protocol (Cisco proprietary)
Network Layer 4-105
RIP ( Routing Information Protocol)
included in BSD-UNIX distribution in 1982 distance vector algorithm
distance metric: # hops (max = 15 hops), each link has cost 1 DVs exchanged with neighbors every 30 sec in response message (aka
advertisement) each advertisement: list of up to 25 destination subnets (in IP addressing
sense)
DC
BA
u v
w
x
yz
subnet hops u 1 v 2 w 2 x 3 y 3 z 2
from router A to destination subnets:
Network Layer 4-106
RIP: example
destination subnet next router # hops to dest
w A 2y B 2
z B 7x -- 1…. …. ....
routing table in router D
w x yz
A
C
D B
Network Layer 4-107
w x yz
A
C
D B
destination subnet next router # hops to dest
w A 2y B 2
z B 7x -- 1…. …. ....
routing table in router D
A 5
dest next hops w - 1 x - 1 z C 4 …. … ...
A-to-D advertisement
RIP: example
Network Layer 4-108
RIP: link failure, recovery if no advertisement heard after 180 sec -->
neighbor/link declared dead routes via neighbor invalidated new advertisements sent to neighbors neighbors in turn send out new advertisements
(if tables changed) link failure info quickly (?) propagates to entire
net poison reverse used to prevent ping-pong
loops (infinite distance = 16 hops)
Network Layer 4-109
RIP table processing
RIP routing tables managed by application-level process called route-d (daemon)
advertisements sent in UDP packets, periodically repeated
physical
link
network forwarding (IP) table
transport (UDP)
routed
physical
link
network (IP)
transprt (UDP)
routed
forwardingtable
Network Layer 4-110
OSPF (Open Shortest Path First) “open”: publicly available uses link state algorithm
LS packet dissemination topology map at each node route computation using Dijkstra’s algorithm
OSPF advertisement carries one entry per neighbor
advertisements flooded to entire AS carried in OSPF messages directly over IP
(rather than TCP or UDP) IS-IS routing protocol: nearly identical to
OSPF
Network Layer 4-111
OSPF “advanced” features (not in RIP) security: all OSPF messages authenticated