7/13/2019 Chapter 16 Microwave Communications
1/106
2008 The McGraw-Hill Com anies
1
Principles of ElectronicCommunication Systems
Third Edition
Louis E. Frenzel, Jr.
7/13/2019 Chapter 16 Microwave Communications
2/106
2008 The McGraw-Hill Com anies
2
Chapter 16
Microwave Communication
7/13/2019 Chapter 16 Microwave Communications
3/106
2008 The McGraw-Hill Com anies
3
Topics Covered in Chapter 16
16-1: Microwave Concepts
16-2: Microwave Lines and Devices
16-3: Waveguides and Cavity Resonators
16-4: Microwave Semiconductor Diodes
16-5: Microwave Tubes
16-6: Microwave Antennas
16-7: Microwave Applications
7/13/2019 Chapter 16 Microwave Communications
4/106
2008 The McGraw-Hill Com anies
4
16-1: Microwave Concepts
Microwavesare the ultrahigh, superhigh, and
extremely high frequencies directly above the lower
frequency ranges where most radio communication
now takes place and below the optical frequenciesthat cover infrared, visible, and ultraviolet light.
7/13/2019 Chapter 16 Microwave Communications
5/106
2008 The McGraw-Hill Com anies
5
16-1: Microwave Concepts
Microwave Frequencies and Bands
The practical microwave region is generally consideredto extend from 1 to 30 GHz, although frequencies couldinclude up to 300 GHz.
Microwave signals in the 1- to 30-GHz havewavelengths of 30 cm to 1 cm.
The microwave frequency spectrum is divided up intogroups of frequencies, or bands.
Frequencies above 40 GHz are referred to asmillimeter (mm) wavesand those above 300 GHz arein the submillimeterband.
7/13/2019 Chapter 16 Microwave Communications
6/106
2008 The McGraw-Hill Com anies
6
16-1: Microwave Concepts
Figure 16-1: Microwave
frequency bands.
7/13/2019 Chapter 16 Microwave Communications
7/106 2008 The McGraw-Hill Com anies
7
16-1: Microwave Concepts
Benefits of Microwaves
Moving into higher frequency ranges has helped tosolve the problem of spectrum crowding.
Today, most new communication services are assignedto the microwave region.
At higher frequencies there is a greater bandwidthavailable for the transmission of information.
Wide bandwidths make it possible to use various
multiplexing techniques to transmit more information.
Transmission of high-speed binary information requireswide bandwidths and these are easily transmitted onmicrowave frequencies.
7/13/2019 Chapter 16 Microwave Communications
8/106 2008 The McGraw-Hill Com anies
8
16-1: Microwave Concepts
Disadvantages of Microwaves
The higher the frequency, the more difficult it becomes
to analyze electronic circuits.
At microwave frequencies, conventional componentsbecome difficult to implement.
Microwave signals, like light waves, travel in perfectly
straight lines. Therefore, communication distance is
limited to line-of-sight range. Microwave signals penetrate the ionosphere, so
multiple-hop communication is not possible.
7/13/2019 Chapter 16 Microwave Communications
9/106 2008 The McGraw-Hill Com anies
9
16-1: Microwave Concepts
Microwave Communication Systems
Like any other communication system, a microwavecommunication system uses transmitters, receivers,and antennas.
The same modulation and multiplexing techniques usedat lower frequencies are also used in the microwaverange.
The RF part of the equipment, however, is physically
different because of the special circuits andcomponents that are used to implement thecomponents.
7/13/2019 Chapter 16 Microwave Communications
10/106 2008 The McGraw-Hill Com anies
10
16-1: Microwave Concepts
Microwave Communication Systems: Transmitters
Like any other transmitter, a microwave transmitter
starts with a carrier generator and a series of amplifiers.
It also includes a modulator followed by more stages ofpower amplification.
The final power amplifier applies the signal to the
transmission line and antenna.
A transmitter arrangement could have a mixer used toup-convert an initial carrier signal with or without
modulation to the final microwave frequency.
7/13/2019 Chapter 16 Microwave Communications
11/106 2008 The McGraw-Hill Com anies
11
16-1: Microwave Concepts
Figure 16-3: Microwave transmitters. (a) Microwave transmitter using frequency
multipliers to reach the microwave frequency. The shaded stages operate in the
microwave region.
7/13/2019 Chapter 16 Microwave Communications
12/106 2008 The McGraw-Hill Com anies
12
16-1: Microwave Concepts
Figure 16-3: Microwave transmitters. (b) Microwave transmitter using up-conversion
with a mixer to achieve an output in the microwave range.
7/13/2019 Chapter 16 Microwave Communications
13/106 2008 The McGraw-Hill Com anies
13
16-1: Microwave Concepts
Microwave Communication Systems: Receivers
Microwave receivers, like low-frequency receivers, are
the superheterodyne type.
Their front ends are made up of microwavecomponents.
Most receivers use double conversion.
7/13/2019 Chapter 16 Microwave Communications
14/106 2008 The McGraw-Hill Com anies
14
16-1: Microwave Concepts
Microwave Communication Systems: Receivers
The antenna is connected to a tuned circuit, which
could be a cavity resonator or microstrip or stripline
tuned circuit. The signal is then applied to a special RF amplifier
known as a low-noise amplifier (LNA).
Another tuned circuit connects the amplified input signal
to the mixer. The local oscillator signal is applied to the mixer.
The mixer output is usually in the UHF or VHF range.
The remainder of the receiver is typical of other
superheterodynes.
7/13/2019 Chapter 16 Microwave Communications
15/106 2008 The McGraw-Hill Com anies
15
16-1: Microwave Concepts
Figure 16-4: A microwave receiver. The shaded areas denote microwave circuits.
16
7/13/2019 Chapter 16 Microwave Communications
16/106 2008 The McGraw-Hill Com anies
16
16-1: Microwave Concepts
Microwave Communication Systems: TransmissionLines
Coaxial cable, most commonly used in lower-frequencycommunication has very high attenuation at microwavefrequencies and conventional cable is unsuitable forcarrying microwave signals.
Special microwave coaxial cable that can be used onbands L, S, and C is made of hard tubing. This low-loss
coaxial cable is known as hard line cable. At higher microwave frequencies, a special hollow
rectangular or circular pipe called waveguideis usedfor the transmission line.
17
7/13/2019 Chapter 16 Microwave Communications
17/106 2008 The McGraw-Hill Com anies
17
16-1: Microwave Concepts
Microwave Communication Systems: Antennas
At low microwave frequencies, standard antenna types,
including the simple dipole and one-quarter wavelength
vertical antenna, are still used. At these frequencies antennas are very small; for
example, a half-wave dipole at 2 GHz is about 3 in.
At higher microwave frequencies, special antennas are
generally used.
18
7/13/2019 Chapter 16 Microwave Communications
18/106 2008 The McGraw-Hill Com anies
18
16-2: Microwave Lines and Devices
Although vacuum and microwave tubes like the
klystron and magnetron are still used, most microwave
systems use transistor amplifiers.
Special geometries are used to make bipolartransistors that provide voltage and power gain at
frequencies up to 10 GHz.
Microwave FET transistors have also been created.
Monolithic microwave integrated circuits (MMICs) are
widely used.
19
7/13/2019 Chapter 16 Microwave Communications
19/106 2008 The McGraw-Hill Com anies
19
16-2: Microwave Lines and Devices
Microstrip Tuned Circuits
At higher frequencies, standard techniques for
implementing lumped components such as coils and
capacitors are not possible. At microwave frequencies, transmission lines,
specifically microstrip, are used.
Microstrip is preferred for reactive circuits at the higher
frequencies because it is simpler and less expensivethan stripline.
Stripline is used where shielding is necessary.
20
7/13/2019 Chapter 16 Microwave Communications
20/106 2008 The McGraw-Hill Com anies
20
16-2: Microwave Lines and Devices
Figure 16-6: Microstrip transmission line used for reactive circuits. (a) Perspective
view. (b) Edge or end view. (c) Side view (open line). (d) Side view (shorted line).
21
7/13/2019 Chapter 16 Microwave Communications
21/106 2008 The McGraw-Hill Com anies
21
16-2: Microwave Lines and Devices
Figure 16-7: Equivalent circuits of open and shorted microstrip lines.
22
7/13/2019 Chapter 16 Microwave Communications
22/106 2008 The McGraw-Hill Com anies
22
16-2: Microwave Lines and Devices
Microstrip Tuned Circuits
An important characteristic of microstrip is its
impedance.
The characteristic impedance of a transmission linedepends on its physical characteristics.
The dielectric constant of the insulating material is also
a factor.
Most characteristic impedances are less than 100 . One-quarter wavelength transmission line can be used
to make one type of component look like another.
23
7/13/2019 Chapter 16 Microwave Communications
23/106 2008 The McGraw-Hill Com anies
23
16-2: Microwave Lines and Devices
Figure 16-8: How a one-quarter wavelength microstrip can transform impedances
and reactances.
24
7/13/2019 Chapter 16 Microwave Communications
24/106 2008 The McGraw-Hill Com anies
24
16-2: Microwave Lines and Devices
Microstrip Tuned Circuits
Microstrip can also be used to realize coupling from onecircuit.
One microstrip line is simply placed parallel to anothersegment of microstrip.
The degree of coupling between the two depends onthe distance of separation and the length of the parallelsegment.
The closer the spacing and the longer the parallel run,the greater the coupling.
Microstrip patterns are made directly onto printed-circuitboards.
25
7/13/2019 Chapter 16 Microwave Communications
25/106 2008 The McGraw-Hill Com anies
25
16-2: Microwave Lines and Devices
Microstrip Tuned Circuits
A special form of microstrip is the hybrid ring.
The unique operation of the hybrid ring makes it very
useful for splitting signals or combining them. Microstrip can be used to create almost any tuned
circuit necessary in an amplifier, including resonant
circuits, filters, and impedance-matching networks.
26
7/13/2019 Chapter 16 Microwave Communications
26/106 2008 The McGraw-Hill Com anies
26
16-2: Microwave Lines and Devices
Figure 16-12: A microstrip hybrid ring.
27
7/13/2019 Chapter 16 Microwave Communications
27/106 2008 The McGraw-Hill Com anies
27
16-2: Microwave Lines and Devices
Microwave Transistors
The primary differences between standard lower-
frequency transistors and microwave types are internal
geometry and packaging. To reduce internal inductances and capacitances of
transistor elements, special chip configurations known
as geometriesare used.
Geometries permit the transistor to operate at higherpower levels and at the same time minimize distributed
and stray inductances and capacitances.
28
7/13/2019 Chapter 16 Microwave Communications
28/106
2008 The McGraw-Hill Com anies
28
16-2: Microwave Lines and Devices
Microwave Transistors
The GaAs MESFET, a type of JFET using a Schottkybarrier junction, can operate at frequencies above 5GHz.
A high electron mobility transistor (HEMT)is avariant of the MESFET and extends the range beyond20 GHz by adding an extra layer of semiconductormaterial such as AlGaAs.
A popular device known as a heterojunction bipolartransistor (HBT)is making even higher-frequencyamplification possible in discrete form and in integratedcircuits.
29
7/13/2019 Chapter 16 Microwave Communications
29/106
2008 The McGraw-Hill Com anies
29
16-2: Microwave Lines and Devices
Figure 16-14: Microwave transistors. (a) and (b) Low-power small signal. (c) FET
power. (d) NPN bipolar power.
30
7/13/2019 Chapter 16 Microwave Communications
30/106
2008 The McGraw-Hill Com anies
30
16-2: Microwave Lines and Devices
Small-Signal Amplifiers
A small-signal microwave amplifier can be made up of a
single transistor or multiple transistors combined with a
biasing circuit and any microstrip circuits or componentsas required.
Most microwave amplifiers are of the tuned variety.
Another type of small-signal microwave amplifier is a
multistage integrated circuit,a variety of MMIC.
31
7/13/2019 Chapter 16 Microwave Communications
31/106
2008 The McGraw-Hill Com anies
31
16-2: Microwave Lines and Devices
Small-Signal Amplifiers: Transistor Amplifiers
A low-noise transistor with a gain of about 10 to 25 dBis typically used as a microwave amplifier.
Most microwave amplifiers are designed to have inputand output impedances of 50 .
The transistor is biased into the linear region for class Aoperation.
RFCs are used in the supply leads to keep the RF out
of the supply and to prevent feedback paths that cancause oscillation and instability in multistage circuits.
Ferrite beads (FB) are used in the collector supply leadfor further decoupling.
32
7/13/2019 Chapter 16 Microwave Communications
32/106
2008 The McGraw-Hill Com anies
32
16-2: Microwave Lines and Devices
Small-Signal Amplifiers: MMIC Amplifiers
A common monolithic microwave integrated circuit(MMIC)amplifier is one that incorporates two or morestages of FET or bipolar transistors made on a common
chip to form a multistage amplifier.
The chip also incorporates resistors for biasing andsmall bypass capacitors.
Physically, these devices look like transistors.
Another form of MMIC is the hybrid circuit,whichcombines an amplifier IC connected to microstripcircuits and discrete components.
33
7/13/2019 Chapter 16 Microwave Communications
33/106
2008 The McGraw-Hill Com anies
33
16-2: Microwave Lines and Devices
Figure 16-15: A single-stage class A RF microwave amplifier.
34
7/13/2019 Chapter 16 Microwave Communications
34/106
2008 The McGraw-Hill Com anies
34
16-2: Microwave Lines and Devices
Small-Signal Amplifiers: Power Amplifiers
A typical class A microwave power amplifier is designedwith microstrip lines used for impedance matching andtuning.
Input and output impedances are 50 .
Typical power-supply voltages are 12, 24, and 28 volts.
Most power amplifiers obtain their bias from constant-current sources.
A single-stage FET power amplifier can achieve apower output of 100 W in the high UHF and lowmicrowave region.
35
7/13/2019 Chapter 16 Microwave Communications
35/106
2008 The McGraw-Hill Com anies
16-2: Microwave Lines and Devices
Figure 16-16: A class A microwave power amplifier.
36
7/13/2019 Chapter 16 Microwave Communications
36/106
2008 The McGraw-Hill Com anies
16-2: Microwave Lines and Devices
Figure 16-17: A constant-current bias supply for a linear power amplifier.
37
7/13/2019 Chapter 16 Microwave Communications
37/106
2008 The McGraw-Hill Com anies
16-2: Microwave Lines and Devices
Figure 16-18: An FET power amplifier.
38
16 3 W id
7/13/2019 Chapter 16 Microwave Communications
38/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Waveguides
Most microwave energy transmission above 6 GHz ishandled by waveguides.
Waveguides are hollow metal conducting pipesdesigned to carry and constrain the electromagneticwaves of a microwave signal.
Most waveguides are rectangular.
Waveguides are made from copper, aluminum or brass.
Often the insides of waveguides are plated with silver toreduce resistance and transmission losses.
39
16 3 W id
7/13/2019 Chapter 16 Microwave Communications
39/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Waveguides: Signal Injection and Extraction
A microwave signal to be carried by a waveguide isintroduced into one end of the waveguide with anantennalike probe.
The probe creates an electromagnetic wave thatpropagates through the waveguide.
The electric and magnetic fields associated with thesignal bounce off the inside walls back and forth as the
signal progresses down the waveguide. The waveguide totally contains the signal so that none
escapes by radiation.
40
16 3 W id
7/13/2019 Chapter 16 Microwave Communications
40/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Figure 16-19: Injecting a sine wave into a waveguide and extracting a signal.
41
16 3 W id
7/13/2019 Chapter 16 Microwave Communications
41/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Waveguides: Signal Injection and Extraction
Probes and loops can be used to extract a signal from a
waveguide.
When the signal strikes a probe or a loop, a signal isinduced which can then be fed to other circuitry through
a short coaxial cable.
42
16 3 W id
7/13/2019 Chapter 16 Microwave Communications
42/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Waveguides: Waveguide Size and Frequency.
The frequency of operation of a waveguide is
determined by the inside width of the pipe (dimension
(a) in the figure following).
This dimension is usually made equal to one-half
wavelength, a bit below the lowest frequency of
operation. This frequency is known as the waveguide
cutoff frequency.
At its cutoff frequency and below, a waveguide will not
transmit energy.
Above the cutoff frequency, a waveguide will propagate
electromagnetic energy.
43
16 3 W id
7/13/2019 Chapter 16 Microwave Communications
43/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Figure 16-20: The dimensions of a waveguide determine its operating frequency range.
44
16 3 W id
7/13/2019 Chapter 16 Microwave Communications
44/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Waveguides: Signal Propagation
In a waveguide, when the electric field is at a right angle
to the direction of wave propagation, it is called a
transverse electric (TE) field.
Whenthe magnetic field is transverse to the direction of
propagation, it is called a transverse magnetic (TM)
field.
45
16 3 W id
7/13/2019 Chapter 16 Microwave Communications
45/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Waveguides: Signal Propagation
The angles of incidence and reflection depend on the
operating frequency.
At high frequencies, the angle is large and the pathbetween the opposite walls is relatively long.
As the operating frequency decreases, the angle also
decreases and the path between the sides shortens.
When the operating frequency reaches the cutofffrequency of the waveguide, the signal bounces back
and forth between the sidewalls of the waveguide. No
energy is propagated.
46
16 3 W id
7/13/2019 Chapter 16 Microwave Communications
46/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Figure 16-22: Wavepaths in awaveguide atvarious
frequencies.(a) Highfrequency.
(b) Mediumfrequency.
(c) Lowfrequency.
(d) Cutofffrequency.
47
16 3: Wa eg ides
7/13/2019 Chapter 16 Microwave Communications
47/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Waveguides: Signal Propagation
When a microwave signal is launched into a waveguide
by a probe or loop, electric and magnetic fields are
created in various patterns depending upon the method
of energy coupling, frequency of operation, and size of
waveguide.
The pattern of the electromagnetic fields within a
waveguide takes many forms. Each form is called an
operating mode.
48
16 3: Waveguides
7/13/2019 Chapter 16 Microwave Communications
48/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Figure 16-23: Electric (E ) and magnetic (H) fields in a rectangular waveguide.
49
16 3: Waveguides
7/13/2019 Chapter 16 Microwave Communications
49/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Waveguide Hardware and Accessories
Waveguides have a variety of special parts, such as
couplers, turns, joints, rotary connections, and
terminations.
Most waveguides and their fittings are precision-made
so that the dimensions match perfectly.
A choke jointis used to connect two sections of
waveguide. It consists of two flanges connected to thewaveguide at the center.
A T sectionor T junctionis used to split or combine
two or more sources of microwave power.
50
16 3: Waveguides
7/13/2019 Chapter 16 Microwave Communications
50/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Figure 16-25: A choke joint permits sections of waveguide to be interconnected with
minimum loss and radiation.
51
16 3: Waveguides
7/13/2019 Chapter 16 Microwave Communications
51/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Waveguide Hardware and Accessories: Directional
Couplers
One of the most commonly used waveguide
components is the directional coupler. Directional couplersare used to facilitate the
measurement of microwave power in a waveguide and
the SWR.
They can also be used to tap off a small portion of ahigh-power microwave signal to be sent to another
circuit or piece of equipment.
52
16 3: Waveguides
7/13/2019 Chapter 16 Microwave Communications
52/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Figure 16-30: Directional coupler.
53
16 3: Waveguides
7/13/2019 Chapter 16 Microwave Communications
53/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Cavity Resonator
A cavity resonator is a waveguide-like device that acts
like a high-Qparallel resonant circuit.
A simple cavity resonator can be formed with a shortpiece of waveguide one-half wavelength long.
Energy is coupled into the cavity with a coaxial probe at
the center.
The internal walls of the cavity are often plated withsilver or some other low-loss material to ensure
minimum loss and maximum Q.
54
16 3: Waveguides
7/13/2019 Chapter 16 Microwave Communications
54/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Figure 16-31: Cavity resonator made with waveguide. (b) Side view of cavity
resonator showing coupling of energy by a probe.
55
16 3: Waveguides
7/13/2019 Chapter 16 Microwave Communications
55/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Circulators
A circulatoris a three-port microwave device used for
coupling energy in only one direction around a closed
loop.
Microwave energy is applied to one port and passed to
another with minor attenuation, however the signal will
be greatly attenuated on its way to a third port.
The primary application of a circulator is a diplexer,which allows a single antenna to be shared by a
transmitter and receiver.
56
16 3: Waveguides
7/13/2019 Chapter 16 Microwave Communications
56/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Figure 16-31 Cavity resonator made with waveguide. (a) A section of rectangular
waveguide used as a cavity resonator. (b) Side view of cavity resonator showing
coupling of energy by a probe.
57
16 3: Waveguides
7/13/2019 Chapter 16 Microwave Communications
57/106
2008 The McGraw-Hill Com anies
16-3: Waveguides
and Cavity Resonators
Isolators
Isolators are variations of circulators, but they have one
input and one output.
They are configured like a circulator, but only ports 1and 2 are used.
Isolators are often used in situations where a mismatch,
or the lack of a proper load, could cause reflection so
large as to damage the source.
58
16 4: Microwave
7/13/2019 Chapter 16 Microwave Communications
58/106
2008 The McGraw-Hill Com anies
16-4: Microwave
Semiconductor Diodes
Small Signal Diodes
Diodes used for signal detection and mixing are the
most common microwave semiconductor devices.
Two types of widely used microwave diodes are: Point-contact diode
Schottky barrier or hot-carrier diode
59
16 4: Microwave
7/13/2019 Chapter 16 Microwave Communications
59/106
2008 The McGraw-Hill Com anies
16-4: Microwave
Semiconductor Diodes
Small Signal Diodes: Point-Contact Diode
The oldest microwave semiconductor device is the
point-contact diode, also called a crystal diode.
A point-contact diode is a piece of semiconductormaterial and a fine wire that makes contact with thesemiconductor material.
Point-contact diodes are ideal for small-signalapplications.
They are widely used in microwave mixers anddetectors and in microwave power measurementequipment.
60
16 4: Microwave
7/13/2019 Chapter 16 Microwave Communications
60/106
2008 The McGraw-Hill Com anies
16-4: Microwave
Semiconductor Diodes
Figure 16-35: A point-contact diode.
61
16-4: Microwave
7/13/2019 Chapter 16 Microwave Communications
61/106
2008 The McGraw-Hill Com anies
16-4: Microwave
Semiconductor Diodes
Small Signal Diodes: Hot Carrier Diodes
For the most part, point-contact diodes have been
replaced by Schottky diodes, sometimes referred to as
hot carrier diodes.
Like the point-contact diode, the Schottky diode isextremely small and has a tiny junction capacitance.
Schottky diodes are widely used in balancedmodulators and mixers.
They are also used as fast switches at microwavefrequencies.
62
16-4: Microwave
7/13/2019 Chapter 16 Microwave Communications
62/106
2008 The McGraw-Hill Com anies
16-4: Microwave
Semiconductor Diodes
Figure 16-36: Hot carrier or Schottky diode.
63
16-4: Microwave
7/13/2019 Chapter 16 Microwave Communications
63/106
2008 The McGraw-Hill Com anies
16-4: Microwave
Semiconductor Diodes
Frequency-Multiplier Diodes
Microwave diodes designed primarily for frequency-
multiplier service include:
Varactor diodes Step-recovery diodes
64
16-4: Microwave
7/13/2019 Chapter 16 Microwave Communications
64/106
2008 The McGraw-Hill Com anies
16 4: Microwave
Semiconductor Diodes
Frequency-Multiplier Diodes: Varactor Diodes
A varactor diode is basically a voltage variable
capacitor.
When a reverse bias is applied to the diode, it acts likea capacitor.
A varactor is primarily used in microwave circuits as afrequency multiplier.
Varactors are used in applications in which it is difficult
to generate microwave signals.
Varactor diodes are available for producing relativelyhigh power outputs at frequencies up to 100 GHz.
65
16-4: Microwave
7/13/2019 Chapter 16 Microwave Communications
65/106
2008 The McGraw-Hill Com anies
16 4: Microwave
Semiconductor Diodes
Figure 16-37: A varactor frequency multiplier.
66
16-4: Microwave
7/13/2019 Chapter 16 Microwave Communications
66/106
2008 The McGraw-Hill Com anies
16 4: Microwave
Semiconductor Diodes
Frequency-Multiplier Diodes: Step-Recovery Diodes
A step-recovery diodeor snap-off varactoris widely
used in microwave frequency-multiplier circuits.
A step-recovery diode is a PN-junction diode made withgallium arsenide or silicon.
When it is forward-biased, it conducts as any diode, but
a charge is stored in the depletion layer.
When reverse bias is applied, the charge keeps thediode on momentarily and then turns off abruptly.
This snap-off produces a high intensity reverse-current
pulse that is rich in harmonics.
67
16-4: Microwave
7/13/2019 Chapter 16 Microwave Communications
67/106
2008 The McGraw-Hill Com anies
16 4: Microwave
Semiconductor Diodes
Oscillator Diodes
Three types of diodes other than the tunnel diode that
can oscillate due to negative resistance characteristics
are:
Gunn diode
IMPATT diode
TRAPATT diode
68
16-4: Microwave
7/13/2019 Chapter 16 Microwave Communications
68/106
2008 The McGraw-Hill Com anies
16 4: Microwave
Semiconductor Diodes
Oscillator Diodes: Gunn Diodes
Gunn diodes, also called transferred-electron
devices (TEDs),are not diodes in the usual sense
because they do not have junctions.
A Gunn diode is a thin piece of N-type gallium arsenide(GaAs) or indium phosphide (InP) semiconductor whichforms a special resistor when voltage is applied to it.
The Gunn diode exhibits a negative-resistance
characteristic. Gunn diodes oscillate at frequencies up to 150 GHz.
69
16-4: Microwave
7/13/2019 Chapter 16 Microwave Communications
69/106
2008 The McGraw-Hill Com anies
16 4: Microwave
Semiconductor Diodes
Oscillator Diodes: IMPATT and TRAPATT Diodes
Two microwave diodes widely used as oscillators arethe IMPATT and TRAPATT diodes.
Both are PN-junction diodes made of silicon, GaAs, or
InP. They are designed to operate with a high reverse bias
that causes them to avalanche or break down.
IMPATT diodes are available with power ratings up to
25 W to frequencies as high as 300 GHz. IMPATT are preferred over Gunn diodes if higher power
is required.
70
16-4: Microwave
7/13/2019 Chapter 16 Microwave Communications
70/106
2008 The McGraw-Hill Com anies
16 4: Microwave
Semiconductor Diodes
PIN Diodes
A PIN diodeis a special PN-junction diode with an I(intrinsic) layer between the P and the N sections.
The P and N layers are usually silicon, although GaAs
is sometimes used and the I layer is a very lightly dopedN-type semiconductor.
PIN diodes are used as switches in microwave circuits.
PIN diodes are widely used to switch sections of
quarter- or half-wavelength transmission lines to providevarying phase shifts in a circuit.
71
16 5 Mi T b
7/13/2019 Chapter 16 Microwave Communications
71/106
2008 The McGraw-Hill Com anies
16-5: Microwave Tubes
Vacuum tubesare devices used for controlling a
large current with a small voltage to produce
amplification, oscillation, switching, and other
operations.
Vacuum tubes are used in microwave transmitters
requiring high output power.
Special microwave tubes such as the klystron, the
magnetron, and the traveling-wave tube are widelyused for microwave power amplification.
72
16 5 Mi T b
7/13/2019 Chapter 16 Microwave Communications
72/106
2008 The McGraw-Hill Com anies
16-5: Microwave Tubes
Klystrons A klystronis a microwave vacuum tube using cavity
resonators to produce velocity modulation of an electronbeam that produces amplification.
Klystrons are no longer widely used in most microwaveequipment.
Gunn diodes have replaced the smaller reflex klystronsin signal-generating applications because they are
smaller and lower in cost. The larger multicavity klystrons are being replaced by
traveling-wave tubes in high-power applications.
73
16 5 Mi T b
7/13/2019 Chapter 16 Microwave Communications
73/106
2008 The McGraw-Hill Com anies
16-5: Microwave Tubes
Magnetrons A widely used microwave tube is the magnetron, a
combination of a simple diode vacuum tube with built-incavity resonators and an extremely powerful permanent
magnet. Magnetrons are capable of developing extremely high
levels of microwave power.
When operated in a pulsed mode, magnetrons can
generate several megawatts of power. A typical application for a continuous-wave magnetron
is for heating purposes in microwave ovens.
74
16 5 Mi T b
7/13/2019 Chapter 16 Microwave Communications
74/106
2008 The McGraw-Hill Com anies
16-5: Microwave Tubes
Figure 16-40: A magnetron tube used as an oscillator.
75
16 5 Mi T b
7/13/2019 Chapter 16 Microwave Communications
75/106
2008 The McGraw-Hill Com anies
16-5: Microwave Tubes
Traveling-Wave Tubes One of the most versatile microwave RF power
amplifiers is the traveling-wave tube (TWT),which cangenerate hundreds and even thousands of watts of
microwave power. The main advantage of the TWT is an extremely wide
bandwidth.
Traveling-wave tubes can be made to amplify signals in
a range from UHF to hundreds of gigahertz. A common application of TWTs is as power amplifiers in
satellite transponders.
76
16 5 Mi T b
7/13/2019 Chapter 16 Microwave Communications
76/106
2008 The McGraw-Hill Com anies
16-5: Microwave Tubes
Figure 16-41: A traveling-wave tube (TWT).
77
16 6 Mi A t
7/13/2019 Chapter 16 Microwave Communications
77/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Because of the line-of-sight transmission of microwave
signals, highly directive antennas are preferred
because they do not waste the radiated energy and
because they provide an increase in gain, which helps
offset noise at microwave frequencies.
78
16 6 Mi A t
7/13/2019 Chapter 16 Microwave Communications
78/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Low-Frequency Antennas
At low microwave frequencies, less than 2 GHz,
standard antennas are commonly used, including the
dipole and its variations.
The corner reflectoris a fat, wide-bandwidth, half-
wave dipole fed with low-loss coaxial cable.
The overall gain of a corner reflector antenna is 10 to 15
dB.
79
16 6 Mi A t
7/13/2019 Chapter 16 Microwave Communications
79/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Figure 16-42: A corner reflector used with a dipole for low microwave frequencies.
80
16 6: Micro a e Antennas
7/13/2019 Chapter 16 Microwave Communications
80/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Horn Antenna Microwave antennas must be some extension of or
compatible with a waveguide.
Waveguide are not good radiators because they
provide a poor impedance match with free space. Thisresults in standing waves and reflected power.
This mismatch can be offset by flaring the end of thewaveguide to create a horn antenna.
Horn antennas have excellent gain and directivity.
The gain and directivity of a horn are a direct function ofits dimensions; the most important dimensions arelength, aperture area, and flare angle.
81
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
81/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Figure 16-43: Basic horn antenna.
82
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
82/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Parabolic Antennas
A parabolic reflectoris a large dish-shaped structure
made of metal or screen mesh.
The energy radiated by the horn is pointed at thereflector, which focuses the radiated energy into a
narrow beam and reflects it toward its destination.
Beam widths of only a few degrees are typical with
parabolic reflectors.
Narrow beam widths also represent extremely high
gains.
83
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
83/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Figure 16-48: Cross-sectional view of a parabolic dish antenna.
84
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
84/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Parabolic Antennas: Feed Methods
A popular method of feeding a parabolic antenna is an
arrangement known as a Cassegrain feed.
The horn antenna is positioned at the center of the
parabolic reflector.
At the focal point is another small reflector with either a
parabolic or a hyperbolic shape.
The electromagnetic radiation from the horn strikes thesmall reflector, which then reflects the energy toward
the large dish which radiates the signal in parallel
beams.
85
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
85/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Figure 16-51: Cassegrain feed.
86
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
86/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Helical Antennas A helical antenna, as its name suggests, is a wire helix.
A center insulating support is used to hold heavy wire ortubing formed into a circular coil or helix.
The diameter of the helix is typically one-thirdwavelength, and the spacing between turns isapproximately one-quarter wavelength.
The gain of a helical antenna is typically in the 12- to
20-dB range and beam widths vary from approximately12to 45.
Helical antennas are favored in many applicationsbecause of their simplicity and low cost.
87
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
87/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Figure 16-52: The helical antenna.
88
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
88/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Bicone Antennas
One of the most widely used omnidirectional microwave
antennas is the bicone.
The signals are fed into bicone antennas through a
circular waveguide ending in a flared cone.
The upper cone acts as a reflector, causing the signal to
be radiated equally in all directions with a very narrow
vertical beam width.
89
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
89/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Figure 16-53: The omnidirectional bicone antenna.
90
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
90/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Slot Antennas A slot antennais a radiator made by cutting a one-half
wavelength slot in a conducting sheet of metal or intothe side or top of a waveguide.
The slot antenna has the same characteristics as astandard dipole antenna, as long as the metal sheet isvery large compared to at the operating frequency.
Slot antennas are widely used on high-speed aircraft
where the antenna can be integrated into the metallicskin of the aircraft.
91
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
91/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Figure 16-54: Slot antennas on a waveguide. (a) Radiating slots. (b) Nonradiating
slots.
92
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
92/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Dielectric (Lens) Antennas Dielectricor lens antennasuse a special dielectric
material to collimate or focus the microwaves from asource into a narrow beam.
Lens antennas are usually made of polystyrene or someother plastic, although other types of dielectric can beused.
Their main use is in the millimeter range above 40 GHz.
93
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
93/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Figure 16-57: Lens antenna operations. (a) Dielectric lens. (b) Zoned lens.
94
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
94/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Patch Antennas Patch antennasare made with microstrip on PCBs.
The antenna is a circular or rectangular area of copperseparated from the ground plane on the bottom of the
board by the PCBs insulating material. Patch antennas are small, inexpensive, and easy to
construct.
Their bandwidth is directly related to the thickness of
the PCB material. Their radiation pattern is circular in the direction
opposite to that of the ground plane.
95
16 6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
95/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Phased Arrays A phased arrayis an antenna system made up of a
large group of similar antennas on a common plane.
Patch antennas on a common PCB can be used, orseparate antennas like dipoles can be mountedtogether in a plane.
The basic purpose of an array is to improve gain anddirectivity.
Arrays also offer better control of directivity, since
individual antennas in an array can be turned off or on,or driven through different phase shifters.
Most phased arrays are used in radar systems, but theyare finding applications in some cell phone systems andin satellites.
96
16-6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
96/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Figure 16-59: An 8 8 phase array using patch antennas. (Feed lines are not
shown.)
97
16-6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
97/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Printed-Circuit Antennas
Because antennas are so small at microwave
frequencies, they can be conveniently made right on a
printed-circuit board that also holds the transmitter
and/or receiver ICs and related circuits.
No separate antenna structure, feed line, or connectors
are needed.
In addition to the patch and slot antennas, the loop,the
inverted-F,and the meander line antennasare also
used.
98
16-6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
98/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Intelligent Antenna Technology
Intelligent antennasor smart antennasare antennas
that work in conjunction with electronic decision-making
circuits to modify antenna performance to fit changing
situations.
They adapt to the signals being received and the
environment in which they transmit.
99
16-6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
99/106
2008 The McGraw-Hill Com anies
16-6: Microwave Antennas
Intelligent Antenna Technology
Also called adaptive antennas,these new designs
greatly improve transmission and reception in multipath
environments and can also multiply the number of users
of a wireless system.
Some popular adaptive antennas today use diversity,
multiple-input multiple-output, and automatic beam
forming.
10
16-6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
100/106
2008 The McGraw-Hill Com anies
16 6: Microwave Antennas
Adaptive Beam Forming
Adaptive antennasare systems that automatically
adjust their characteristics to the environment.
They use beam-forming and beam-pointing techniques
to zero in on signals to be received and to ensure
transmission under noisy conditions.
Beam-forming antennas use multiple antennas such as
phase arrays.
10
16-6: Microwave Antennas
7/13/2019 Chapter 16 Microwave Communications
101/106
2008 The McGraw-Hill Com anies
16 6: Microwave Antennas
Adaptive Beam Forming There are two kinds of adaptive antennas: switched
beam arraysand adaptive arrays.
Both switched beam arrays and adaptive arrays are
being employed in some cell phone systems and innewer wireless LANs.
They are particularly beneficial to cell phone systems
because they can boost the system capacity.
10
16-7: Microwave Applications
7/13/2019 Chapter 16 Microwave Communications
102/106
2008 The McGraw-Hill Com anies
16 7: Microwave Applications
Figure 16-64:Majorapplications of microwave
radio.
10
16-7: Microwave Applications
7/13/2019 Chapter 16 Microwave Communications
103/106
2008 The McGraw-Hill Com anies
16 7: Microwave Applications
Radar The electronic communication system known as radar
(radio detection and ranging) is based on the principlethat high-frequency RF signals are reflected by
conductive targets. In a radar system, a signal is transmitted toward the
target and the reflected signal is picked up by a receiverin the radar unit.
The radar unit can determine the distance to a target(range), its direction (azimuth), and in some cases, itselevation (distance above the horizon).
10
16-7: Microwave Applications
7/13/2019 Chapter 16 Microwave Communications
104/106
2008 The McGraw-Hill Com anies
16 7: Microwave Applications
Radar
There are two basic types of radar systems: pulsed and
continuous-wave (CW).
The pulsed type is the most commonly used radar
system.
Signals are transmitted in short bursts or pulses.
The time between transmitted pulses is known as the
pulse repetition time (PRT). In continuous-wave (CW) radar,a constant-amplitude
continuous microwave sine wave is transmitted.
10
16-7: Microwave Applications
7/13/2019 Chapter 16 Microwave Communications
105/106
2008 The McGraw-Hill Com anies
16 7: Microwave Applications
Radar: UWB The newest form of radar is called ultrawideband
(UWB) radar.
It is a form of pulsed radar that radiates a stream of
very short pulses several hundred picoseconds long.
The very narrow pulses give this radar extreme
precision and resolution of small objects and details.
The low power used restricts operation to short
distances.
10
16-7: Microwave Applications
7/13/2019 Chapter 16 Microwave Communications
106/106
16 7: Microwave Applications
Radar: UWB The circuitry used is simple, so it is possible to make
inexpensive, single-chip radars.
These are used in short-range collision detection
systems in airplanes and soon will be in automobiles for
automatic braking based upon distance from the vehicle
ahead.
Another application of UWB radar is personnel
detection on the battlefield. These radars can penetrate
walls to detect the presence of human beings.