7/30/2019 Ch-2-a
1/17
NEED IDENTIFICATION AND PROBLEM DEFINITION
Off all steps of Engineering Design Process, Problem Definition is the most
important
Understanding a problem thoroughly at the beginning aids immeasurably in reachingan outstanding solutions
Off course this holds for all kinds of problems whether maths problem, production
problem or design problem
However, in Product design, where the ultimate test is whether the product sells well
in the marketplace, it is vital to work hard to understand and provide what is that the
customer wants
Before the problem definition step
Case 1: To improve the efficiency of the Cooling Tower
We are facing problem on our cooling towers and are unable to achieve the results as per design
specifications. A brief account of problem we are facing specially during hot season.
1- Condenser inlet temperature (in summer): (Design) 30 C, (Actual) 38 ~ 40 C
2- Condenser outlet temperature (Design) 41 C, (Actual) 49 ~ 50 C
3- Wet bulb temperature (Design) 20 C, (Actual) 26 ~ 27 C
Due to this high temperature of cooling water we can not achieve required
vacuum in condenser and hence low efficiency of the plant.
Case 2: Story of Mariner IV Satellite Project
Design problem may or may not be clear to you based on the information provided
or based on your experience
You would set about defining the problem according to the methods provided in
this book
However, main problem in the problem definition step is the place, where
the Design Process begins, as not all Engineering Tasks are well defined
This step is called as Planning for the Design Process or New Product
Business Development
Engineering Design-ME362 Page 1 of 17 142359893.doc
7/30/2019 Ch-2-a
2/17
Engineering Design-ME362 Page 2 of 17 142359893.doc
7/30/2019 Ch-2-a
3/17
Types of Design Projects
Variation of an Existing Product
o Involves a change of at most a few parameters (Power of motor, design of
fastening bracket)o Required level of expertise is very modest
Improvement of an Existing Product
o Involves more major redesign and is performed to;
To improve performance because of competition
Improve quality or cost in manufacturing
the failure of a vendor to be able to supply specific materials or
components
development of new technology that allows for an improved product Development of a new product for a Low-Volume Production Run
o Prospect of low-quantity production, as opposed to mass production,
constrains the selection of manufacturing processes to those with cheaper
tooling costs
o There is more emphasis on buying off-the-shelf components than in
designing special components.
o Often the first item produced is shipped to the customer is prototype.
Development of a new product for mass productiono Provides engineers flexibility in selecting material and manufacturing
processes (e.g. automobile, major appliances, PCs)
o Require careful planning for manufacture and assembly
One of a kind Design
o Projects can vary from a quick simple design using a minimum analysis
(design of a welding fixture to hold parts) to large expensive system (100-
MW steam turbine)
o For complex systems, due to cost and complexity, prototypes are notfeasible, so must learn from analysis and field experience
o Design evolution is likely to be incremental
o Examples: Large buildings, process plants, power plants etc.
Engineering Design-ME362 Page 3 of 17 142359893.doc
7/30/2019 Ch-2-a
4/17
Engineering Design-ME362 Page 4 of 17 142359893.doc
7/30/2019 Ch-2-a
5/17
CLASS DISCUSSION
Wheelwright-Clark Model of Product Development Process
Q For what type of company this is implemented?
A For a large technology oriented company interested in bringing a steady flow
of new products quickly to market
1. Highly stimulated activity to gather new product ideas from a wide range of sources
2. These include R&D division of the corporation (keeping in view of market etc)
3. First Screen: Not a go-no-go decision point
Instead is a review by midlevel managers to determine what additional information is
needed before a go-no-go decision ca be made at Screen 2
The ideas reviewed at Screen 1 should be checked for
their fitness with the technology
product market strategy of the company
their likely commitment of resources
If Idea Passes this screen
It passes into an area where project bounds are detailed and required knowledge is
specified
If not, then they should be completed
Screen -1 begins to identify competing concepts and ideas
4. Second Screen: It is a go-no-go review in which senior management selects the product and process
option that will become product development project
Any project passed Screen 2 will be funded and staffed with every exception that it will
be carried through to introduction to the market
Time between Screen 1 and 2 is usually between 1 to 2 months and is spent taking the
data and information developed for Screen 1
Engineering Design-ME362 Page 5 of 17 142359893.doc
7/30/2019 Ch-2-a
6/17
Identifying Customer Needs
Increasing worldwide competitiveness brings greater focus on Customers wishes
Engineers and Businessmen require to know: Who are my customers? What doesthe customer want? And How I can provide it?
Japanese say Listen to the Customer
Customer
One that Purchases a product or services (Webster)
Anyone who receives or uses what an individual or organization provides
(TQM)
It is the customers desire that ordinarily drives the development of the product,
not the engineers vision of what the customer should want
Types of CustomerExternal
o
generally definedthis is the definition in mind in most of the peopleo These are people or organizations that buy what the company sells
Internal
o Such as designer who receives information on properties of three potential materials for his
design is an internal customer of the material specialist
o From view point of developing PDS for an improved product, we focus on external
customers, such as end users.
o To complete decisions to make a successful product design, we deal with a host of internal
customers, such as corporate management, manufacturing personnel, sales staff and field
service personnel.
Engineering Design-ME362 Page 6 of 17 142359893.doc
7/30/2019 Ch-2-a
7/17
Gathering information from the Customers
Interviews with customers
o By an active sales force by continuously meetings with present and potential customers
o Responsible to visit key customers for problems areas and maintain and cultivate friendly
contacts
o They should feed back to their design for upgrades or improvements
o Even better that design team to interview some customers in the service environment where
product will be used.
o Key questions can be;
o What do you like or dislike about this product?
o What factors do you consider when purchasing this product?
o What improvements would you make to this product?
Focus Groups
o Arranged discussion with 6~12 customers or potential customers of a product
o Use prepared questions to guide the discussion about merits and demerits of product
o Often in one-way window room for video taping of discussion to record customers response
In both Interview and Focus groups Analysis is held until the analysis of results.
Innovative new products are better explored with interviews or Focus group
discussions
Customer Surveys
o Written questionnaire is best used for gaining opinions for new or redesign
o To know about an implemented solution to problem
o By mail, fax, email or face to face etc
Customer Complaints
o A sure way to learn of needs for product improvement
Engineering Design-ME362 Page 7 of 17 142359893.doc
7/30/2019 Ch-2-a
8/17
Constructing a Survey Instrument
Determine the survey purpose
Determine the type of the data collection
Identify which specific information needed
Design questions (Most important) Basically there are three categories of questions
(1) Attitude question (how the customers feel or think about something)
(2) Knowledge questions (to determine whether the customers knows the specifics about a
product or service)
(3) Behavior questions (usually contain phrases like how often, how much)
Dont use Jargon or sophisticated Vocabulary, Focus very precisely, use simple sentences,
Avoid questions with double negatives to avoid misunderstanding, Always include choice of
Other.., Always include one open ended question.., Questions can have following types of
answers
Yes, No, Dont know, strongly agree, mildly agree, neutral, mildly disagree, strongly disagree
o Number of questions should be such that they can answer within 30 minutes
Arrange the order of questions so that they provide the context to what you are trying to learn.
Group questions by topic and start with easy ones
Pretest the surveys (on a smaller sample of people)
Administer the survey
Engineering Design-ME362 Page 8 of 17 142359893.doc
7/30/2019 Ch-2-a
9/17
Engineering Design-ME362 Page 9 of 17 142359893.doc
7/30/2019 Ch-2-a
10/17
Engineering Design-ME362 Page 10 of 17 142359893.doc
7/30/2019 Ch-2-a
11/17
Engineering Design-ME362 Page 11 of 17 142359893.doc
7/30/2019 Ch-2-a
12/17
Customer Requirements
General Human Needs
Design needs should be related to the basic human needs, some of them may be so obvious that in
our modern technological society they are taken for granted.
However, within each basic need there is a hierarchy of problem situations
Many current design problems deal with type-III situation, in which there is strong societal
disagreement over needs and accompanying goals. Result is protracted delays and increasing costs.
Engineering Design-ME362 Page 12 of 17 142359893.doc
1. Physiological NeedsThrust, Hunger, sleep, shelter,
exercise etc
2. Safety & Security NeedsProtection against danger,
de rivation, threat
3. Social NeedsFor love & esteem by others, interaction etc
5. Psychological NeedsFor self esteem & self respect,
accom lishment and reco nition
4. Self-fulfillment NeedsFor realizing ones full potential,
throu h self-dev., creativit etc
7/30/2019 Ch-2-a
13/17
Customer requirement should be characterized byPerformance, Time, Cost, Quality and Value
Eight basic dimensions of Quality for a manufactured product
Performance, Features, Reliability, Durability, Serviceability, Conformance,
Aesthetics, Perceived Quality
Four Levels of Customer requirement
Expecters Basic required attributes (standard features)
Expecters are easy to measure and are used often in benchmarking
Spokens Specific features required that customer say they want in the product
Designer must try to provide these
Unspokens Customer does not generally talk about, but are nevertheless important to him
They can not be ignored
Customer might have forgotten them to mention or was unwilling to talk about or
simply does not realize he wants
Exciters
Often called delighters These are product features that make it unique and distinguish for competition
Absence of exciter will not make customer unhappy, since they dont know what is
missing
Hierarchy of Customer satisfaction
Expecters Spokens Unspokens Exciters
Engineering Design-ME362 Page 13 of 17 142359893.doc
7/30/2019 Ch-2-a
14/17
Product Design Specification (PDS)
Basic control and reference document for design and manufacture of product
PDS contains all the facts related to the outcome of the product development
Creating PDS finalizes; The process of establishing the customer needs and wants
Prioritizing them
And beginning to cast them into a technical framework so that design concepts can be
established
Elements required in PDS
Engineering Design-ME362 Page 14 of 17 142359893.doc
7/30/2019 Ch-2-a
15/17
Engineering Design-ME362 Page 15 of 17 142359893.doc
7/30/2019 Ch-2-a
16/17
Engineering Design-ME362 Page 16 of 17 142359893.doc
7/30/2019 Ch-2-a
17/17
Engineering Design-ME362 Page 17 of 17 142359893.doc