catalogue.pdf - Gedore South Africa

TOTALRANGE

TO

TA

LR

AN

GE

17 1

8

HEAD OFFICE & FACTORY

NATIONAL NUMBER

0861-GEDORE (0861-433673)

Durban (Latitude: 29.799364 Longitude: 30.880337)

103 Qashana Khuzwayo Road, New Germany, 3610PO Box 68, New Germany, 3620Tel: +27 (0)31 705-3587Fax: +27 (0)31 705-3277Email: [email protected] / [email protected]: www.gedore.co.za

SALES OFFICESJohannesburg (Latitude: 26.078448 Longitude: 28.117125)

26 Village Crescent, Linbro Business ParkPO Box 72, Linbro Park, 2065Tel: +27 (0)11 608-5959Fax: +27 (0)11 608-2953

Cape Town (Latitude: 33.875969 Longitude: 18.500760)

No. 8 Woodbridge Business Park, Koeberg Road, MilnertonPO Box 37299, Chempet, 7442Tel: +27 (0)21 529-6360Fax: +27 (0)21 552-8397 17

18

www.gedore.co.za

WarrantyIn terms of GEDORE’S warranty policy, all torque wrenches are covered by a lifetime guarantee against defective materials and workmanship. Provided that the tool has been correctly used for its intended purpose and allowances have been made for the wear and tear of moving parts, the torque wrench will be repaired free of charge.

The warranty does not cover torque wrenches which have been misused or which have experienced wear and tear through extensive use.

A warranty return will be assessed by our technical sta� and if the return falls outside of our warranty policy, the customer will be noti�ed and quoted for the repair.

CalibrationA standard calibration and the issue of a test certi�cate will be provided as standard practice on any repair conducted.

A SANAS calibration and the issue of a SANAS calibration certi�cate will be done on request at a nominal charge.

ObsolescencePlease note that while GEDORE uses its best endeavours to carry signi�cant stocks of spares to support its torque wrench product range, some spares for older discontinued items are no longer available. In such cases, repair of the torque wrench may not be possible.

“Our guarantee covers all tools against breakage under normal working conditions and is subject to fair wear and tear.”

At GEDORE we take pride in the quality of our products and services and we review all warranty claims with the aim of using the information gained for further product improvement.

Every GEDORE tool is covered by a lifetime guarantee against defective material and workmanship. Provided that the tool has been used correctly for its intended purpose and allowances have been made for wear and tear, this guarantee will allow for the repair or exchange of the tool.

While some deterioration through extensive use might be unavoidable, we will adopt a generous approach when viewing warranty claims. We do, however, set warranty limitations on wear and tear, obvious misuse, missing parts and purposely altered tools to protect ourselves against unreasonable claims.

Should the product fall outside the parameters of the warranty criteria, we will advise the customer on the repair or replacement cost of the article.

© Copyright by Gedore Tools SA (Pty) Ltd.

Gedore strives to be the leading supplier of superior quality tools in Africa and other designated markets.

We seek to build and maintain lasting relationships with customers by responsively o�ering suitable products at fair prices, which consistently conform to the highest level of product and service quality standards.

We strive to increase the value for all stakeholders and to be a preferred supplier, employer and customer.

Quality We strive to be the best that we can be in everything that we do.

Innovation and Knowledge We strive for continuous improvement in all aspects of our business through learning, benchmarking and having a general uneasiness with the status quo.

Responsiveness We have a bias for action by feeling a sense of urgency in everything that we do, and encourage employees to be proactive.

Team Work and Mutual Respect We encourage and support team participation, e�ective communication and mutual respect.

Motivation and People Centred We acknowledge that our employees are the key to our success.

We motivate employees by providing opportunities for advancement, sharing information, fair treatment, training, job security and workplace safety.

Customer Focused We expect all employees to maintain a customer focus in all aspects of their work.

Care for the EnvironmentWe are sensitive of the need to care for the environment and apply ourbusiness processes accordingly.

Corporate Governance We enforce good corporate governance by encouraging honesty, transparency, trust, equity and social responsibility.

DISCLAIMER

As we are constantly improving our products, we reserve the right to make changes as we deem necessary. The actual products delivered may therefore vary from those depicted in the catalogue.We do not provide any warranties in connection with technical and safety information provided in this catalogue. All customers are therefore advised to refer directly to their manufacturer’s speci�cations and the advice and standards of the relevant professional/trade associations. All products remain the property of Gedore Tools SA (Pty) Ltd until paid for in full.We cannot accept any liability for printing errors. Reproduction of any part of this catalogue requires the prior written permission of Gedore Tools SA (Pty) Ltd. All rights reserved worldwide.

GEDORE TOOLS SA WARRANTY POLICY

TORQUE WRENCH WARRANTY &

CALIBRATION POLICY

MISSION STATEMENT

VALUE SYSTEM

Much has changed since our inception in 1965, but the quality of our products has not. This

year we might have a new look, but we remain committed to bringing you the hand tools you know and love.

Last year we launched our new brand identity. Clearly displayed here in our 2017 catalogue, this new-look GEDORE brings a fresh, modern and professional brand identity to echo our world class standards. Page through this 2017 catalogue and you’ll notice that while we may look di�erent, our commitment to bringing you tough tools of the highest quality remains.

This catalogue encompasses over 50 years of innovative product development. In keeping with tradition, this year we’ve released a selection of new tools into the market, including recoil-free hammers, hacksaws, universal pliers, pry bars, engineering tools and various tools sets such as our circlip pliers set and the VDE set. As with all GEDORE tools, these new products carry a lifetime guarantee.

What’s important is that despite these changes our attitude towards our work remains the same. At

New LookSame Outstanding Quality

GEDORE, we manufacture a wide range of hand tools that last a lifetime. Our tools are precision manufactured, hot forged for exceptional durability, and boast the best of German engineering and South African manufacturing to deliver extensive value to our customers across a wide variety of industries.

Whether you’ve used our tools for years or are just starting your journey with us, artisans, tradesmen and workers around the world agree that there are no tools quite like ours. Fiercely reliable, tough and durable no matter the task, our tools will help you get the job done.

So put your trust in GEDORE, because when you do you get more than a tool – you get tools for life.

Should you require pricing on any of the tools featured in this catalogue please do not hesitate to contact us.

1

2

61B

SPANNERS

76PLIERS

134Modular

ASSORTMENTS

212Apprentice

TOOLKITS

64SCREWDRIVERS

3

SPANNERS 6-21

SOCKETS & ACCESSORIES 22-55

IMPACT SOCKETS & ACCESSORIES 56-63

SCREWDRIVERS 64-75

PLIERS 76-97

AUTOMOTIVE & SPECIAL TOOLS 98-113

TOOL ASSORTMENTS 114-139

STRIKING TOOLS 140-145

VDE INSULATED SAFETY TOOLS 146-153

TORQUE TOOLS 154-193

PULLERS 194-205

NON-SPARKING TOOLS 206-211

APPRENTICE TOOLKITS 212-221

ARTISAN TOOLKITS 222-231

SORTIMO 232-237

MERCHANDISERS 238-243

154

TORQUE TOOLS

UNCOMPROMISING AMBITIONControlled screw tightening - reliable and safe for more than 50 years

64SCREWDRIVERS

194PULLERS

154

4

NEW PRODUCTS

142248 ST

RECOIL-FREE HAMMER

84-85PLIERS SETS

1531100-1094

VDE SET

107SAWS

1531100-003

VDE SET

106

PRECISIONENGINEERING TOOLS ENGINEERING TOOLS

5

91

CIRCLIP PLIERS SET

1101-001Made up of most popular sizes and packed in a sturdyplastic case.

95142 10 TL

UNIVERSAL PLIERS

144640 S

SLEDGE HAMMERS

106MEASURING TOOLS

101139PRY BARS

2021101-1.29/3K

BALL BEARING EXTRACTOR SET

108

G-CLAMPS

107ENGINEERS SCRIBER

SPANNERS

SPANNERS, SETS

ADJUSTABLE WRENCHES

COMBINATION SPANNERS

9

FLARE NUT SPANNERS

17

SLOGGING SPANNERS

20

RATCHET SPANNERS

12

OPEN ENDED SPANNERS

18

HOOK SPANNERS

21

RING SPANNERS

14

ADJUSTABLE WRENCHES

19

CROWFOOT SPANNERS

21

Manufacture of hot forged hand tools

Benefits of using a hot forged process of manufacture

A drop forging process is well suited to produce products such as spanners, pliers and puller yokes. Heated raw material is transformed at high speed in a drop forging die to a product closely resembling its �nal form. The process facilitates a pore-free product which has a dense and uniform metallurgical grain structure running parallel to the outer form of the product. This characteristic improves the strength, toughness and elasticity, thereby allowing the application of higher levels of stress.

The forging blank for the spanner is cut from specialised 31CrV3 chrome vanadium steel.

Under carefully controlled conditions, the blank is heated to the correct temperature. It is then forged

between precision manufactured dies, which are mounted on a drop forging hammer.

Surplus material is removed by trimming presses.

A press forging process is well suited for manufacturing products like sockets. Through the use of forging punches, heated round raw material is transformed into a product with a closer tolerance of the �nal socket form.

Drop forged structure Machined or cast structure

UD PROFILE protects bolt heads

The wave form of the ring pro�le allows the spanner to hold in all situations, even where the bolt dimensions are outside the tolerance range.

Torque is transmitted to the �anks of the bolt head. This means that the edges cannot be deformed and the bolt is e�ectively protected.

The contact surface area between the spanner and the bolt head is markedly increased due to the wave form. This allows a more even distribution of the contact pressure, which in turn allows the application of a higher torque.

As the torque is transmitted to the �anks of the bolt, even damaged bolt heads may be gripped and turned.

The ‘open ends’ are precision broached to the specified sizes.

All sharp edges and burrs are removed from the spanner in various grinding processes. The

surface finish is then further improved by a vibro polishing process.

Hardening takes place in a protective gas environment, in which all oxygen has been

removed from the atmosphere. This is done to avoid oxidisation of the metal. After a carefully controlled

water quenching process, the spanner is reheated and tempered to the correct hardness, which ensures

optimum torque and durability.

2

3 4

1

The two-layered nickel/chrome electroplating process provides the spanner with an effective

corrosion protective layer, as well as giving it the distinctive GEDORE satin finish.

SPANNERS

Production of a Spanner

8

Code ! y

6000240 5 100 156000320 5,5 100 15600040 6 100 14600059 7 112 21600067 8 125 25600075 9 138 33600083 10 148 44600091 11 158 50600105 12 168 60600113 13 185 77600121 14 198 88600148 15 210 103600156 16 220 120600164 17 232 140600172 18 245 160600180 19 258 190600199 20 270 220600202 21 280 250600210 22 292 300600229 23 305 335600237 24 318 370600245 25 328 410600253 26 340 450600261 27 352 500600288 28 370 560600296 29 370 570

Code ! y

600318 30 390 645600326 32 412 780002540 33 412 1000600415 34 412 840600342 36 460 1160600350 38 -11/2” 460 1450002527 41 520 1485002528 46 560 1900002529 50 590 2350002530 55 620 36006004070 60 660 36006004660 65 710 45006004740 70 760 56006004820 75 810 65456004900 80 860 8800

1B (AF) SIZES 10

3

Combination Spanners

NO. 1 B – THE STRONG ALL-ROUNDER › According to DIN 3113 Form B, ISO 3318, ISO 7738. › Sizes 5 and 5.5mm with hexagon ring, up from size 6mm with UD pro�le. › GEDORE vanadium steel 31CrV3, chrome-plated. › Carefully forged and professionally machined. › Overloading indicated by deformation.

Slim ribbed open end for added strength

guarantees maximum torques

Jaw: ground precisely to exact nominal

size for optimum contact areas

Ring: 10° o�set from shaft, with UD

pro�le for gentle transmission of force

Non-glare look thanks to

matt chrome plating

› The o�set ring ensures a better grip on deep-seated or inset nuts or bolts. › Top-grade industrial quality for the hardest of continuous use.

1 B (MM) COMBINATION SPANNERS

9

Code ! " Contents 0

601152 1B-04M 10 13 17 19 0.50601160 1B-06M 10 11 13 14 17 19 0.67 601187 1B-08M 10 12 13 14 17 19 22 24 1.38601200 1B-10M 10 11 12 13 14 15 16 17 18 19 2.100601217 1B-12M 10 11 12 13 14 17 19 22 24 27 30 32 3.260601268 1B-17M 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1.910601268TR 1B-17M WITH TOOL ROLL 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 2.270601438 1B-18M 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 2.390601292 1B-TOP 20M 20 MOST POPULAR SIZES 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 27 30 3.373601276 1B-26M 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 32 6.740601276TR 1B-26M WITH TOOL ROLL 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 32 6.740601179 1B-13A 1/4” 5/16” 3/8” 7/16” 1/2” 9/16” 5/8” 11/16” 3/4” 13/16” 7/8” 15/16” 1.” 2.285601209 1B-017A 1/4” 5/16” 3/8” 7/16” 1/2” 9/16” 5/8” 11/16” 3/4” 13/16” 7/8” 15/16” 1.” 1.1/16” 1.1/8” 1.3/16” 1.1/4” 4.765

1425/41/1B FOAM ASSORTMENTS 134SLOGGING SPANNERS 20

SPANNERS

Code " y

600512 1/4” 100 14600520 5/16” 125 25600539 3/8” 148 45600547 7/16” 158 50600555 1/2” 185 80600563 9/16” 198 97600571 5/8” 220 120600598 11/16” 245 174600601 3/4” 258 185600628 13/16” 280 250600636 7/8” 292 300600644 15/16” 318 370600652 1.” 340 450600660 1.1/16” 352 500

31 B (AF) COMBINATION SPANNERSinch

Code " y

600679 1.1/8” 370 570600881 1.3/16” 370 570600687 1.1/4” 412 780600695 1.5/16” 412 790600709 1.3/8” 460 1150600717 1.7/16” 460 1160600725 1.1/2” 460 11706007330 1. 5/8” 520 15006007410 1.3/4” 550 19006007760 1.7/8” 550 19006007840 2” 580 24006007920 2.1/16” 580 32006008060 2.3/16” 620 36006008140 2.1/4” 620 40006008220 2.3/8” 660 44006008300 2.7/16” 660 4800

31 B (MM) / 1 B (AF) COMBINATION SPANNER SETS

10

Code ! y

608955 6 100 12608963 7 110 15608971 8 120 20608998 9 130 32609005 10 140 34609013 11 150 45609021 12 160 50609048 13 170 65609056 14 180 73609064 15 190 90609161 16 200 120609072 17 210 105609188 18 220 165

3

NO. 7 – SLIM LINE › According to DIN 3113 Form A, ISO 3318, ISO 7738. › Gedore vanadium steel 31CrV3, chrome-plated. › Carefully forged and professionally machined. › Slim jaw and jaw walls make this spanner lighter overall. › Overloading indicated by deformation. › Secure grip. › Non-glare look thanks to matt chrome-plating. › Designed for universal use.

Jaw: ground precisely to exact nominal size

for optimum contact areas

Ring: 15° o�set from shaft, with UD

pro�le for gentle transmission of force

Non-glare look thanks to

matt chrome plating

7 (MM) COMBINATION SPANNERSwith same size each end

Code ! y

609080 19 230 150609196 20 240 220609218 21 250 250609099 22 260 215609226 23 270 335609102 24 280 295609234 25 290 410609242 26 300 450609110 27 310 400609250 28 320 440609269 29 330 500609129 30 340 544609137 32 380 624

3 7 (MM) COMBINATION SPANNER SETS

Code ! Contents 0

609358 7-17M 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1.65609579 7-21 M 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 27 30 32 3.70609374 7-26 M 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 32 5.11

11

SPANNERS

Code Contents 0

2297434 7R 8 10 13 17 19 0.930

Code Contents 0

2297442 7R 8 9 10 11 12 13 14 15 16 17 18 19 2.84

3

Combination Ratchet Spanners

THE REVOLUTION › With same size each end. › UD pro�le. › High torque transfer. › Gedore vanadium steel 31CrV3. › Non-glare look thanks to matt chrome-plating,

locking insert and pawl manganese-phosphated. › Hot forged. › Jaw: ground precisely to exact nominal size for

optimum contact areas.

Hollow pro�le comfortable to hold

Non-glare look thanks to matt

chrome plating

Warp-resistant geometry with double

T-girder e�ect

For ratchet loosening

and fast tightening

7 R COMBINATION RATCHET SPANNERS

3 37 R-005 COMBINATION RATCHET SPANNER SET5 pieces

› Most used sizes combined in a set. › Flat pattern. › UD pro�le. › High torque transfer. › In plastic case. › Dimensions: 275 x 150 x 42mm.

7 R-012 COMBINATION RATCHET SPANNER SET12 pieces

› Most used sizes combined in a set. › Flat pattern. › UD pro�le. › High torque transfer. › In robust sheet-metal case. › Dimensions: 320 x 210 x 55mm.

Code ! y

2297051 8 7 140 322297078 9 7 150 422297086 10 7 160 542297094 11 7 164 632297108 12 7 170 692297116 13 7 180 882297124 14 7 190 1012297132 15 7 200 1252297140 16 6 212 1372297159 17 6 225 160

Code ! y

2297167 18 6 237 1972297175 19 6 250 2022219433 21 6 274 2622297191 22 6 292 3192297205 24 6 325 5202297213 27 6 359 5902297221 30 5 399 7802297248 32 5 424 9202219549 34 5 449 10102219557 36 5 480 1208

12

Code ! y 0

1648934 17x19 315 0.501382853 19x22 315 0.701648926 19x24 365 0.70031320 22x24 365 0.80031322 24x27 370 0.806262790 24x30 450 1.40031325 27x30 450 1.40031170 27x32 450 1.40031328 30x36 450 1.40031330 32x36 450 1.60

Reversible ratchet with two di�erent size heads.

Bi-hexagon and ‘rat-tail’ handle.

Code ! y 0

651206 10 177 0.055651214 11 189 0.065651222 12 198 0.075651230 13 208 0.095651249 14 218 0.110651257 15 231 0.120651265 16 244 0.140651273 17 255 0.170651516 18 269 0.220651281 19 283 0.240

3

Swivel Head Wrenches

534 COMBINATION SWIVEL HEAD WRENCHS › Slim pattern, with free moving socket wrench. › With hole for tommy bars 26 D and 26 RS (please order separately). › Gedore vanadium steel 31CrV3, heads polished, chrome-plated.

Friction Type Ratchet

29 I CONSTRUCTION RACHETS

3 534 COMBINATION SWIVEL HEAD WRENCH SETS

Code ! Contents 0

651389 534-6M 10 12 13 14 17 19 1.00651397 534-9M 10 11 12 13 14 15 16 17 19 1.41

13

2 AF RING SPANNER

Code " y 0

003558 13/16x7.8” 285 0.360003561 1.1/16x1.1/4” 370 0.700003567 1.7/16x1.5/8” 440 1.300003568 1.13/16x2” 540 2.200

Code ! y

601535 6x7 170 50601551 8X9 182 65601594 10x11 195 95601659 12x13 212 120601691 14x15 225 155601721 16x17 245 210601748 17x19 265 260601756 18x19 265 260601780 20x22 287 325601799 19x24 305 410601802 21x23 305 410601837 24x26 325 475601853 24x30 345 580601861 25x28 345 580 601918 27x32 370 680 601926 30x32 370 680 601934 30x36 400 1000 601942 32x36 400 1100

Code ! y

003518 36x41 440 1150003519 38x42 440 1200003520 41x46 535 2250003521 46x50 535 2150

3 2 DOUBLE ENDED RING SPANNER SETS › Sets of the most used sizes. › Rings: thin walled with deep o�set. › Chrome Vanadium steel 31CrV3. › In accordance with SANS 1112 and DIN 838.

SPANNERS

Double Ended Ring Spanners

3

2 DOUBLE ENDED RING SPANNERS

NO. 2 – OFFSET › Rings: thin walled with deep o�set. › Chrome VANADIUM steel 31CrV3. › Carefully forged and professionally machined. › Ring: thin-walled, 5° deep o�set from shaft, with UD pro�le for gentle transmission of force.

› High bending strength does not fracture or splinter when overloaded, thus minimising the risk of injury. › In accordance with SANS 1112 and DIN 838.

3

Code ! Contents 0

603058 2-8M 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22 1.38603112 2-11M 6x7 8x9 10x11 12x13 14x15 16x17 17x19 18x19 20x22 21x23 24x30 2.63603090 2-12M 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22 21x23 24x26 25x28 27x32 3.44

14

Code ! y

006001 11x13 152 75006006 13x15 185 1356470120 13x17 185 135006002 14x16 185 1206470390 14x17 185 135006003 15x17 186 120006007 16x18 185 170006005 19x21 233 230006004 19x22 233 230

TORX® = Registered trademark of Acument Intellectual Properties, LLC. USA

Code " y 0

006051 7/16x1/2 150 0.075006052 9/16x5/8 185 0.135006053 3/4x7/8 230 0.275

TX4 FLAT RING SPANNERS - TORX®straight pattern, for protruding TORX® head screws

› Chrome Vanadium steel 31CrV3. › Chrome plated, polished rings. › For outside TORX®.

Code 9 + & y 0

6059800 E6xE8 M5 - M7 5,74 x 7,52 110 0.0146059990 E10xE12 M8 - M10 9,42 x 11,17 140 0.0406060140 E14xE18 M12 - M14 12,9 x 16,7 180 0.0746060220 E20xE24 M16 - M20 18,45 x 22,16 226 0.163

3

3

SPECIAL

› Chrome Vanadium steel 31CrV3. › Chrome plated, polished rings.

304 / 304 (AF) HALF-MOON RING SPANNERS

3 304 HALF-MOON RING SPANNER SETS › Chrome Vanadium steel 31CrV3. › Chrome plated, polished rings.

Code ! Contents 0

634018 6 M 11x13 14x16 15x17 16x18 19x21 19x22 1.20

15

No. 2A + 2 AR

Deep Ring Spanners

NO. 2 A – STRONG › Heavy-duty pattern for highest torques. › Chrome Vanadium steel — 31CrV3. › Optional accessories: No. 2 AR extension tube .

for extending the lever arm.

2 A SINGLE ENDED RING SPANNERSoffset

SPANNERS

Code No. ! y 0

6048600 0 24-30 460 0.606048790 1 32-41 610 1.15

Code ! y 0

6033840 24 180 0.356033920 27 190 0.406034060 30 200 0.456034140 32 235 0.556030150 34 235 0.656034220 36 245 0.656034300 41 265 0.756034490 46 280 1.056034570 50 290 1.156034650 55 300 1.40

For heavy duty ring spanner 2A.

Steel tube, chrome plated.

2AR EXTENSION TUBES

Code ! y 0

6034730 60 345 2.106034810 65 355 2.306035030 70 365 2.606035110 75 375 3.006035380 80 385 3.456035460 85 385 3.806035540 90 410 4.876035620 95 410 4.566035700 100 412 4.50

Code No. ! y 0

6048870 2 46-55 760 2.156048950 3 60-100 860 2.85

16

502 MOTORIST TOOLKIT 1121425/27/SD MODULAR FOAM ASSORTMENT 134

Code ! y 0

005001 8x10 140 0.0456056970 9x11 145 0.050005002 10x11 150 0.0556051070 10x12 150 0.110005003 11x13 160 0.075

3 NO. 400 › Chrome Vanadium steel 31CrV3. › Ring o�set at 15o. Hexagon gap o�set at 30o. › Chrome plated, polished open rings. › In accordance with DIN 3118.

Ring 15° o�set from shaft Hexagon gap 30° o�set,

UD-section at 15° o�set

400 (MM) / 400 (AF) FLARE NUT SPANNERS

inch

Code " y 0

005051 5/16x3/8 140 0.045005053 7/16x1/2 160 0.075

Code ! y 0

005004 12x14 170 0.100005005 14x17 195 0.135005006 17x19 210 0.160005007 22x24 250 0.320

Code " y 0

005055 9/16x5/8 195 0.135005056 5/8x3/4 210 0.160

Flare Nut Spanners

3

3 400 FLARE NUT SPANNER SETS › Chrome Vanadium steel 31CrV3. › Ring o�set at 15o. Hexagon gap o�set at 30o. › Chrome plated, polished open rings. › In accordance with DIN 3118.

Code ! Contents 0

634026 5 M 8X10 11X13 12X14 17X19 22X24 1.20

17

Open Ended Spanners

NO. 6 – STRONG AND ACCURATE › In accordance with SANS 1112 and DIN 895. › Chrome plated. › Slim pattern. › Chrome Vanadium steel 31CrV3.

Non-glare look thanks

to matt chrome plating

Jaw: ground precisely to exact nominal

size for optimum contact areas

Secure grip thanks to

slim pro�le shaft

Slim pattern

6 (MM) DOUBLE OPEN ENDED SPANNERS

6 DOUBLE OPEN ENDED SPANNER SETS

Code ! y 0

606383 6x7mm 122 0.020606421 8x9mm 140 0.025606448 8x10mm 140 0.030606472 10x11mm 157 0.040606537 12x13mm 172 0.060606588 14x15mm 188 0.070606626 16x17mm 205 0.110606642 17x19mm 222 0.155606650 18x19mm 222 0.155606677 19x22mm 236 0.210606685 20x22mm 236 0.210

Code ! y 0

606707 21x23mm 247 0.240606731 24x26mm 266 0.300606758 24x27mm 266 0.300606774 25x28mm 280 0.355004518 27x32mm 302 0.460606812 30x32mm 302 0.460004520 32x36mm 328 0.650004521 36x41mm 360 0.850004522 38x42mm 360 0.800004523 41x46mm 400 1.100004524 46x50mm 450 1.600

SPANNERS

Code ! Contents 0

607703 4 M 10x11 12x13 14x15 16x17 0.28607711 6 M 8x9 10x11 12x13 14x15 16x17 19x22 0.51607738 8 M 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22 0.69607754 10 M 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22 21x23 24x27 1.23607878 11 M 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22 21x23 24x27 30x32 1.69607770 12 M 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22 21x23 24x26 25x28 27x32 2.04

18

62 ADJUSTABLE WRENCHESopen end, phosphated

› Chrome Vanadium steel 31CrV3. › Swedish pattern - jaw set at 15o. › Manganese phosphate �nish. › In accordance with SANS 1211 and DIN 3117. › Ground head.

* Available in blister.

V62 ADJUSTABLE WRENCH 149

Knurl / Pin / SpringE 62 BCD

JAWE 62 A

536806 E 62 A / 150 Jaw536814 E 62 A / 200 Jaw536822 E 62 A / 250 Jaw536830 E 62 A / 300 Jaw536849 E 62 A / 375 Jaw536857 E 62 A / 450 Jaw536717 E 62 BCD / 150 Knurl / Pin / Spring536725 E 62 BCD / 200 Knurl / Pin / Spring536733 E 62 BCD / 250 Knurl / Pin / Spring536741 E 62 BCD / 300 Knurl / Pin / Spring536768 E 62 BCD / 375 Knurl / Pin / Spring536776 E 62 BCD / 450 Knurl / Pin / Spring

62 SPARES

62H ADJUSTABLE WRENCHES Chrome Vanadium steel 31CrV3.

Swedish pattern - jaw set at 15o.

Manganese phosphate �nish.

In accordance with SANS 1211 and DIN 3117.

Ground head.

PVC handle for comfort.

Code No.

VDE SPANNERS 148

Code ! y 0

636800 150* 20 150 0.155636819 200* 25 200 0.250636827 250* 30 250 0.460636835 300* 36 300 0.700

Code ! y 0

636843 375 43 375 1.030636851 450 53 450 1.6756360880 P 24” / 600 63 610 3.480

Code ! y 0

636762 150H 20 150 0.150636770 200H 25 200 0.300

Code ! y 0

636789 250H 30 250 0.450636797 300H 36 300 0.750

Adjsutable Wrenches

19

Code ! y 0

009000 25 180 0.40009002 27 180 0.40009003 30 190 0.50009004 32 195 0.60009035 34 195 0.60009005 36 210 0.80009006 41 225 1.00009007 46 255 1.30009008 50 280 1.706400850 55 310 2.706400930 60 310 2.706401070 65 360 3.406401150 70 360 4.606401230 75 395 5.906401310 80 410 7.006401580 85 410 6.806401660 90 455 10.006401740 95 455 9.506401820 100 500 14.606401900 105 500 13.506402040 110 500 13.306402120 115 525 16.806402200 120 525 17.10

Code " y 0

010051 15/16” 185 0.40010050 1” 185 0.40010053 1.1/8” 185 0.40010054 1.1/4” 195 0.50010056 1.7/16” 200 0.70010057 1.1/2” 200 0.60010058 1.5/8” 225 0.80010059 1.11/16” 225 0.80010060 1.3/4” 240 1.10010062 1.7/8” 240 1.10010063 2” 250 1.206479930 2.3/16” 260 1.606480000 2.1/4” 260 1.606480190 2.3/8” 270 1.606480350 2.9/16” 290 2.206480430 2.5/8” 290 2.206480510 2.3/4” 325 2.406480780 3” 325 3.106480860 3.1/8” 345 3.70

Code ! y 0

010001 24 185 0.30010002 27 185 0.40010003 30 195 0.50010004 32 195 0.50010035 34 195 0.40010005 36 200 0.706474460 38 205 0.66010006 41 225 0.80010007 46 240 1.10010008 50 250 1.206475940 55 260 1.506476080 60 270 1.606476160 65 290 2.206476240 70 325 2.506476320 75 325 3.206476400 80 345 3.606476590 85 345 3.906476670 90 380 7.006476750 95 380 7.006476830 100 410 6.606476910 105 415 9.606477050 110 435 9.606477130 115 435 9.606477210 120 480 9.806477480 125 510 9.806477560 130 510 13.60

1“ SOCKET SET 53

IMPACT SOCKETS 56

Chrome Vanadium steel 31CrV3.

Designed for heavy duty applications.

Shot blast �nish.

In accordance with DIN 133.


Designed for heavy duty applications.

Shot blast �nish.

In accordance with DIN 7444.

SPANNERS

Slogging Spanners

306 (MM) / 306 (AF) RING SLOGGING SPANNERS

inch

133 (MM) OPEN ENDED SLOGGING SPANNERS

20

Code ! y 0

6670050 13 160 0.1006670130 14 160 0.1006676920 16 200 0.1706670210 17 200 0.1506677060 18 200 0.2206670480 19 200 0.2506677140 21 200 0.2606670560 22 200 0.3006670640 24 250 0.4506670720 27 250 0.5006670800 30 250 0.6506670990 32 250 0.7006671020 36 315 1.1506671290 46 315 1.5006671370 50 315 1.600

Code ) y 0

6335850 16 - 18 110 0.0206335930 20 - 22 110 0.0256336580 25 - 28 135 0.0406336660 30 - 32 135 0.0456336740 34 - 36 170 0.0756336820 40 - 42 170 0.0806336900 45 - 50 205 0.1156337040 52 - 55 205 0.1206337120 58 - 62 240 0.2006337200 68 - 75 240 0.2106337390 80 - 90 280 0.2906337470 95 -100 280 0.300

Code , y 0

6354480 3 178 0.1356354560 4 178 0.1406354640 5 230 0.2756354720 6 230 0.2756354990 8 230 0.285

Code ) y 0

6333990 16 - 20 110 0.0206334020 25 - 28 135 0.0406334100 30 - 32 135 0.0456334290 34 - 36 170 0.0756334370 40 - 42 170 0.0806334450 45 - 50 205 0.1156334530 52 - 55 205 0.1206334610 58 - 62 240 0.2006334880 68 - 75 240 0.2106334960 80 - 90 280 0.2906335180 95 - 100 280 0.3006335260 110 - 115 335 0.480

Hook Spanners

Crowfoot Spanners

44

CALIPER FACE SPANNERS


Manganese phosphated.

Similar to DIN 3116..

40

HOOK SPANNERS

In accordance with DIN 1810, Form A.



For slotted round nuts.

3114

CROWFOOT SPANNERS

40Z

PIN SPANNERS


Chrome plated.

Opening at right angle to handle for maximum accessibility.

In accordance with DIN 1810, Form A.



For cross-drilled nuts.

OPEN ENDED SLOGGING SPANNERS

21

SOCKETS

SOCKETS &

ACCESSORIES

(1/4”) SETS / RATCHETS

25

(3/8”) SOCKETS / ACCESSORIES

29


48


26


32


50


28


42

(1”) SETS / RATCHETS / SOCKETS / ACCESSORIES 53

Sets (1/4")

For manually operated sockets and accessories with 1/4” square drive.


Dimensions: 200x120x38mm.

R (1/4") square drive

b !

20 E SOCKET SETS 1/4"16 pieces

Code No. Ratchet Sockets Accessories 0

6172100 No.20EMZ ! 2093 Z-94 1 20 4 4,5 5 6 7 8 9 10 11 13 + 2087 2090-4

) 2095 - 2098

0.71

6172450 No.20EAU-3 # 2093 U-3 1 20 3/16 7/32 1/4 9/32 5/16 11/32 3/8 7/16 1/2

+ 2087 ‚ 2090-4 ) 2095 - 2098

0.76

Outside diameter turned and knurled using high-

tech CNC machinery.

4.

Counterbored, square socket drive fluted, manu-

facturer and socket size permanently stamped.

5.

A key feature of GEDORE’S socket manufacture is the use of chrome vanadium steel in a hot forging process. As the heated metal is forged, the grains are bent to follow the shape of the forging die, thus maintaining an unbroken grain structure throughout the article. This grain structure and the resulting elastic and toughness properties of a GEDORE socket can easily be compared to the �brous resilience of a tree branch.

As chrome vanadium steel cannot be cold forged, GEDORE’S competitors using cold forging processes are forced to use metallurgically modi�ed steels to accommodate this type of manufacture, resulting in inferior elastic and toughness properties.

In summaryGEDORE sockets are hot forged to obtain a superior strength to weight ratio. Competitor sockets are cold forged primarily to reduce manufacturing cost.

Blank cropped to size from 31CrV3.

Machined to size.Hot forged in the forging press.

1. 2. 3.

Degreased – grease would destroy

the protective gas atmos-phere in hardening.

6.

Hardened under protective gas

atmosphere, followed by annealing.

Nickel plated and matt-chrome plated. The electrolytically applied nickel coating ensures

corrosion protection. The electroplated chrome improves the

look and gives the socket a perfect finish.

Sand blasted in preparation for surface coating.

7. 8. 9.

Hot forged. Cold forged.

24

SOCKETS

Socket Manufacturing Process

m b

Ratchets (1/4")

2093 U-10 REVERSIBLE RATCHET 1/4"

› Particularly for the demanding use experienced in industry and with utility vehicles. › According to DIN 3122, ISO 3315. › With recessed lever change, locks in middle position. › Return angle of �ve degrees. › Non-slip 2-component handle with hanging hole. › For hand-operated sockets and accessories with square drive

as per DIN 3120 - C 6.3, ISO 1174. › Ball locking device. › Gedore vanadium steel 31CrV3, chrome plated.


› Especially for working in con�ned spaces, as in the automotive business. › According to DIN 3122, ISO 3315. › With non-slip metal disc change, �ne-toothed (72 teeth) and robust. › Return angle of �ve degrees. › Non-slip 2-component handle with hanging hole. › For hand-operated sockets and accessories with square drive


Code No. a „ a A° y 0

6170590 2093 U-3 1/4 6.3 5 129 0.095Code No. a „ a A° y 0

6180470 2093 U-10 1/4 6.3 15 129 0.109

2093 Z-94 RATCHET HANDLE WITH COUPLER 1/4"

› Used throughout industry and the automotive world. › According to DIN 3122, ISO 3315. › With square coupler, medium-�ne toothed, extremely rugged. › Return angle of eighteen degrees. › For hand-operated sockets and accessories with square drive



6170750 2093 Z-94 1/4 6.3 18 129 0.076

Code ! y 0

6165400 No.20 4mm 25 0.0096165670 No.20 5mm 25 0.0106165830 No.20 6mm 25 0.0106165910 No.20 7mm 25 0.0126166050 No.20 8mm 25 0.0146166130 No.20 9mm 25 0.0166166210 No.20 10mm 25 0.0206166480 No.20 11mm 25 0.0256166560 No.20 12mm 25 0.0306166640 No.20 13mm 25 0.035

R 1 20 (MM)

SOCKETS 1/4"hexagon

› Manually operated sockets with knurled base. › Chrome Vanadium steel 31CrV3. › Chrome plated and polished. › In accordance with SANS 1113 and DIN 3120.

Sockets (1/4")

25

3/8“ SOCKETS 29

20L (MM) SOCKETS 1/4"hexagon, long pattern

› Manually operated sockets with knurled base. › Chrome Vanadium steel 31CrV3. › Chrome plated and polished. › In accordance with SANS 1113 and DIN 3120.

R 1

Code ! y 0

6191400 4.0 50 0.0176191590 4.5 50 0.0176191670 5.0 50 0.0186191750 5.5 50 0.0196191830 6.0 50 0.0206191910 7.0 50 0.0246192050 8.0 50 0.0276192130 9.0 50 0.0306192210 10.0 50 0.0336192480 11.0 50 0.0476192560 12.0 50 0.0506192640 13.0 50 0.054

IN20L (MM) SCREWDRIVER BIT SOCKET 1/4"for in-hex screws, long pattern

R

Code No. 7 + & y 0

6190430 ITX 20 T8 T8 M2,5 2,31 30.5 0.0136190780 ITX 20 T10 T10 M3 - M3,5 2,74 30.5 0.0146190860 ITX 20 T15 T15 M3,5 - M4 3,27 30.5 0.0146190940 ITX 20 T20 T20 M4 - M5 3,86 30.5 0.0146191080 ITX 20 T25 T25 M4,5 - M5 4,43 30.5 0.0146191160 ITX 20 T27 T27 M4,5 - M6 4,99 30.5 0.0146191240 ITX 20 T30 T30 M6 - M7 5,52 30.5 0.0156265890 ITX 20 T40 T40 M7 - M8 6,65 33.5 0.025

ITX20 SCREWDRIVER BIT SOCKET 1/4“for recessed TORX® head screws

R

› Manually operated sockets with knurled base. › Chrome Vanadium steel 31CrV3. › Chrome plated and polished. › In accordance with SANS 1113 and DIN 3120. › TORX® = registered trademark of Acument Intellectual

Properties, LLC. USA

Code No. ? K L y 0

6171560 IS 20 4x0,8 4.0 0.8 28 0.0116171640 IS 20 5,5x1 5.5 1.0 28 0.0126174230 IS 20 6,5x1,2 6.5 1.2 28 0.0126174310 IS 20 8x1,6 8.0 1.6 28 0.012

Code No. ; PH y 0

6174580 IKS 20 1 1 28 0.0116174660 IKS 20 2 2 28 0.0126174740 IKS 20 3 3 28 0.012

IS 20 SCREWDRIVER BIT SOCKET 1/4"for slotted head screws

R

IKS 20 SCREWDRIVER BIT SOCKET 1/4"for cross-head screws PH

R IKS 20 PZD SCREWDRIVER BIT SOCKET 1/4"for cross-head screws Pozi PZ

R

› Square drive as per DIN 3120 - C 6.3, ISO 1174, with ball retaining groove › Manually operated sockets with knurled base. › Chrome plated and polished. › Chrome Vanadium steel 31CrV3.


Code No. < PZ y 0

6187130 IKS 20 PZD 1 1 28 0.0126187210 IKS 20 PZD 2 2 28 0.0136187480 IKS 20 PZD 3 3 28 0.014

R

26

SOCKETS


Code $ y 0

1933256 3 60 0.0241933264 4 60 0.0251933272 5 60 0.0271933280 6 60 0.0291933299 8 60 0.050


› For manually operated sockets and accessories with 1/4” square drive. › ChromeVanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3123.

Accessories (1/4")

2097 SWIVEL HANDLE 1/4" › For manually operated sockets and accessories with 1/4” square drive. › Chrome Vanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3122.

2098 DRIVING HANDLE 1/4" › According to DIN 3122, ISO 3315. › For hand-operated sockets with square drive as per DIN 3120, ISO 1174 › Ball locking device

Code No. a „ a y 0

6171050 2097 1/4 6.3 146 0.094Code No. a „ a y 0

6171480 2098 1/4 6.3 140 0.070


6170240 2088 1/4 6.3 140 0.045

2090-4

2090 EXTENSIONS 1/4"


6170320 2090-2 1/4 6.3 55 0.0256170400 2090-4 1/4 6.3 97 0.0416171210 2090-6 1/4 6.3 148 0.0616173340 2090-12 1/4 6.3 305 0.124

3/8“1/4“10 mm6,3 mm

2095 UNIVERSAL JOINT 1/4" › For manually operated sockets and accessories with 1/4” square drive. › ChromeVanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3123.

2094 COUPLER 1/4" › For manually operated sockets and accessories with 1/4” square drive. › ChromeVanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3123.

2030 CONVERTER 1/4" TO 3/8" › For manually operated sockets and accessories

with 1/4” square drive. › ChromeVanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3123.

2087 SLIDING T-BAR 1/4" › For manually operated sockets and accessories with 1/4” square drive. › ChromeVanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3123.


6170160 2087 1/4 6.3 115 0.039Code No. a „ a y 0

6170910 2095 1/4 6.3 38 0.026


6170830 2094 1/4 6.3 19.8 0.006Code No. Q

„Q a

„a y 0

6170080 2030 1/4 6.3 3/8 10 26 0.020

R

27

2088 FLEXIBLE EXTENSION 1/4" › For manually operated sockets and accessories with 1/4” square drive. › Chrome Vanadium steel 31CrV3.

545767 3096 Repair Kit545759 3093 U-3 Repair Kit

S (3/8") Square Drive

Sets (3/8")

514632 D 19 K Box514640 D 19 J Box515175 D 30 F Insert515280 D 30 H Insert

28

SOCKETS

c ! D30 FMZ

SOCKET SET 3/8"21 pieces

› Manually operated 3/8” sockets and accessories. › Supplied in blue powder coated, D19 K steel box. › Dimensions: 281x77x37mm.


623202 D30 FMZ ! 3093 Z-94 3 D 30 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

3090-125 1.49

c ! D30 HMZ

SOCKET SET 3/8"25 pieces

› Manually operated 3/8” sockets and accessories. › Supplied in blue powder coated, D19 J steel box. › Dimensions: 290x186x52mm.

30 SPARES 3/8" › For the 3096 power bar and 3093 U-3 ratchet. › For F and H socket sets. Blue powder coated steel case. › Black matt-�nish insert.


623962 D30 HMZ ! 3093 Z-94 3 D 30 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

+ 3087 3090-250 3090-125

) 3095 C 3081

2.75


› For manually operated sockets and accessories with 3/8” square drive. › Chrome Vanadium steel 31CrV3. › With non-slip metal disc change, �ne-toothed (72 teeth) and robust. › Return angle of �ve degrees. › In accordance with SANS 1113 and DIN 3122.

Ratchets 10 (3/8")

3093 Z-94 RATCHET HANDLE WITH COUPLER 3/8" › For manually operated sockets and accessories with 3/8” square drive. › Chrome Vanadium steel 31CrV3. › With non-slip metal disc change, �ne-toothed (72 teeth) and robust. › Return angle of ten degrees. › In accordance with SANS 1113 and DIN 3122.


6237090 3093 U-3 3/8 10 5 200 0.244Code No. a „ a A° y 0

6237680 3093 Z-94 3/8 10 10 200 0.223

Sockets (3/8")

S

D 30 (MM) SOCKETS 3/8"bi-hexagon UD profile

› Manually operated sockets with thin walls and knurled base. › Chrome Vanadium steel 31CrV3. › Chrome plated and polished. › In accordance with SANS 1113 and DIN 3124.

3 3

Code ! y 0

6230160 No.30 6mm* 28 0.0256230240 No.30 7mm* 28 0.0246230320 No.30 8mm* 28 0.0246230400 No.30 9mm* 28 0.0276230590 No.30 10mm* 28 0.0296230670 D30 11mm 28 0.0296230750 D30 12mm 28 0.0336230830 D30 13mm 28 0.0386230910 D30 14mm 28 0.0396231050 D30 15mm 30 0.0406231130 D30 16mm 30 0.0466231210 D30 17mm 30 0.0566231480 D30 18mm 30 0.0586231560 D30 19mm 30 0.0666231640 D30 20mm 30 0.0666231720 D30 21mm 30 0.0786231800 D30 22mm 31 0.088

*Hexagon

Code ! y 0

2016613 D30 1/4AF 28 0.0252101009 D30 9/32AF 28 0.0241997122 D30 5/16AF 28 0.0242101017 D30 11/32AF 28 0.0261997130 D30 3/8AF 28 0.0326232610 D30 7/16AF 28 0.0286232880 D30 1/2AF 28 0.0386232960 D30 9/16AF 28 0.0356233180 D30 19/32AF 30 0.0416233260 D30 5/8AF 30 0.0466233340 D30 11/16AF 30 0.0566233420 D30 3/4AF 30 0.0651997157 D30 25/32AF 30 0.0701997165 D30 13/16AF 30 0.0746232020 D30 7/8AF 31 0.083

S

D 30 (AF) SOCKETS 3/8"bi-hexagon UD profile

› Manually operated sockets with thin walls and knurled base. › Chrome Vanadium steel 31CrV3. › Chrome plated and polished. › In accordance with SANS 1113 and DIN 3124.

*Hexagon

S

29

TORX® = Registered trademark of Acument Intellectual Properties, LLC. USA.



6237760 3094 3/8 10 29 0.019

Code No. a „

a Q „

Q y 0

6238140 3095 3/8 10 3/8 10 54 0.053

Code No. a „

a Q „

Q y 0

6236010 3019 1/2 12,5 3/8 10 36 0.057

S TX 30 SOCKETS 3/8"for protruding TORX® head screws

S

N S

ITX 30 SCREWDRIVER BIT SOCKETS 3/8"for recessed TORX® head screws

IN 30 (MM) SCREWDRIVER BIT SOCKETS 3/8"for in-hex screws

Code ! 9 + & y 0

6250270 TX30 E5 E5 M4 4.73 28 0.0256250350 TX30 E6 E6 M5 5.74 28 0.0256250430 TX30 E7 E7 M6 6.16 28 0.0256250510 TX30 E8 E8 M6-M7 7.52 28 0.027

Code ! 9 + & y 0

6246320 ITX30 T 20 T20 M4-M5 3.86 49 0.0506246830 ITX30 T 25 T25 M4,5-M5 4.43 49 0.0516247210 ITX30 T 27 T27 M4.5-M6 4.99 49 0.0516247560 ITX30 T 30 T30 M6-M7 5.52 49 0.0516247720 ITX30 T 40 T40 M7-M8 6.65 49 0.052

Code No.L 0

6241010 IN30 4mm 47 0.038

6241280 IN30 5mm 47 0.39

6241360 IN30 6mm 47 0.041

6241440 IN30 8mm 49 0.053

6242920 IN30 10mm 49 0.073

Accessories (3/8")

S

30

SOCKETS

1/2“3/8“12,5 mm10 mm

3095 UNIVERSAL JOINT 3/8"

3094 COUPLER 3/8" › For manually operated sockets and accessories

with 3/8” square drive. › Chrome Vanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3122.

3019 CONVERTER 3/8" TO 1/2"

› For manually operated sockets and accessories with 3/8” square drive. › CHROME VANADIUM steel – 59CrV4. › In accordance with SANS 1113 and DIN 3122.

› For manually operated sockets and accessories with 3/8” square drive. › CHROME VANADIUM steel – 59CrV4. › In accordance with SANS 1113 and DIN 3122.

Code No. a „

a Q „

Q y 0

6236280 3020 1/4 6,3 3/8 10 28 0.026

3087 SLIDING T-BAR 3/8" › For manually operated sockets and accessories

with 3/8” square drive. › Chrome Vanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3122.

› For manually operated sockets and accessories with 3/8” square drive. › Chrome Vanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3122.

3081 L-HANDLE 3/8"

Code No. a „

a y 0

6236280 3081 3/8 10 180 0.163

Code No. a „

a y 0

6236520 3087 3/8 10 163 0.128

3090-75

3090-125

3090-250



Code No. a „

a y 0

6236600 3090/ 75 3/8 10 75 0.0716236790 3090/125 3/8 10 125 0.1106236870 3090/250 3/8 10 250 0.197

3096 SWIVEL HANDLE 3/8"

Code No. a „

a y 0

6238220 3096 3/8 10 250 0.171

S

31

3/8“ 1/4“10 mm 6,3 mm

3020 REDUCER 3/8" TO 1/4"



T (1/2") square drive

Sets (1/2")

Code No. Sockets 0

612936 C19 MK C19 8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 19-3/4 22 23 24-15/16 26 -1. 27-1.1/16 28 30-1.3/16 32-1.1/4

2.27

614122 D19 MK D19 8 10 11 12 13 14 15 16 17 19 22 23 24 26 27 28 30 32

2.43

616419 D19 AK D19 5/16AF 11/32AF 3/8AF 7/16AF 1/2AF 9/16AF 19/32AF 5/8AF 11/16AF 3/4AF 13/16AF 7/8AF 15/16AF 1.AF 1.1/16AF 1.1/8AF 1.3/16AF 1.1/4AF

2.25

32

SOCKETS

d ! 19 AK / MK

SOCKET SETS 1/2"20 pieces

› Manually operated 1/2” sockets. › Supplied in blue powder coated, D19 K steel box. › Dimensions: 281x77x46mm.

Code No. Sockets 0

612286 C19 HMZ C19 8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 19-3/4 22

1.94

Accessories ! 1993 Z-94 1990/125 Extension

614610 D19 HMZ D19 8 10 11 12 13 14 15 16 17 19 22 1.93


612316 C19 KMZ C19 10-3/8 12 13-1/2 14 15-19/32 17 19-3/4 22 24-15/16 27-1.1/16

2.01


614653 D19 KMZ D19 10 12 13 14 15 17 19 22 24 27 2.05Accessories ! 1993 Z-94 1990/125 Extension

d ! 19 HMZ / KMZ

SOCKET SETS 1/2"15 / 14 pieces

› Manually operated 1/2” sockets and accessories. › Supplied in blue powder coated, D19 K steel box. › Dimensions: 281x77x46mm.

Code No. Sockets 0

611921 SR-C19Z 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 19-3/4 22

1.39

Accessories ! 1993 Z-94 1990/75 Extension Socket Rail

616834 SR-D19Z 10 12 13 14 15 16 17 19 22 24 1.46

Accessories ! 1993 Z-94 1990/75 Extension Socket Rail

T ! 19 SR


› Manually operated 1/2” sockets and accessories. › Blister packed.

K19 IMPACT SOCKET SET 58

K1900 IMPACT DRIVER SET 58

Code No. 1B Spanners Ratchet Sockets Accessories 0

612928 C19 1BMZ 10 11 13 14 17 19 22 ! 1993 Z-94 10-3/8 11 12 13-1/2 14 15-19/3216-5/8 17 19-3/4 22

1990-125145-250137-250

4.56

615595 D19 1BMZ 10 11 13 14 17 19 22 ! 1993 Z-94 10 11 12 13 14 15 16 17 1 9 22 1990-125145-250137-250

4.54

T

33

T !

19 1BMZ SOCKET SETS 1/2"23 pieces

› Manually operated 1/2” sockets and accessories. › Supplied in blue powder coated, D19 J steel box.


616699 D19 GMU-10T $ 1993 U-10 T 10 11 12 13 14 15 17 18 19 21 22 24

+ 1987 1990-125 1990-250

5.70

611956 C19 GMU-10T $ 1993 U-10 T 10 11 12 13 14 15 17 18 19 21 22 24

+ 1987 1990-125 1990-250

5.70

T ! 19 GMU-10T


› Manually operated 1/2” sockets and accessories. › Supplied in blue powder coated, D19 J steel box. › Dimensions: 290x186x52mm.

T

34

SOCKETS


611980 C19/22 TMZ ! 1993 Z-94 8-5/16 9-11/32 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 20-25/32 21-13/16 22 24-15/16 26 -1.27-1.1/16 28 29-1.1/8 30-1.3/16 32-1.1/4

1990-125 1990-250

+ 1987) 1995

5.20

616524 D19/22 TMZ ! 1993 Z-94 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 26 27 28 29 30 32

1990-125 1990-250

+ 1987) 1995

5.20

T ! 19/22 TMZ


› Manually operated 1/2” sockets and accessories. › Supplied in blue powder coated, D19 T steel box. › Dimensions: 435x170x50mm.


611999 C19/22 TMU-10T $ 1993 U-10 T 8-5/16 9-11/32 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/1619-3/4 20-25/32 21-13/16 22 24-15/16 26 -1. 27-1.1/16 28 29-1.1/8 30-1.3/16 32-1.1/4

+ 1987 1990-125 1990-250

) 1995

5.40

616532 D19/22 TMU-10T $ 1993 U-10 T 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 26 27 28 29 30 32

+ 1987 1990-125 1990-250

) 1995

5.40

T ! 19/22 TMU-10T



T

35


612413 C19 TM97U-10T $ 1993 U-10 T 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 30-1.3/16 32-1.1/4

1990-125 1990-250

1997-37550-20.8

4.54

615455 D19 TM97U-10T $ 1993 U-10 T 10 11 12 13 14 15 16 17 19 20 22 24 27 30 32

1990-125 1990-250

1997-37550-20.8

4.74

T ! 19 TM97U-10T




612464 C19 TMU-10T $ 1993 U-10 T 8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26 -1.27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4

+ 1987 1990-125 1990-250

) 19951985

5.62

615196 D19 TMU-10T $ 1993 U-10 T 8 10 11 12 13 14 15 16 17 19 21 22 23 24 26 27 28 30 32

+ 1987 1990-125 1990-250

) 1995 1985

5.70

616206 D19 TAU-10T $ 1993 U-10 T 5/16AF 3/8AF 13/32AF 7/16AF 1/2AF9/16AF 19/32AF 5/8AF 11/16AF 3/4AF25/32AF 13/16AF 7/8AF 15/16AF 1. AF1.1/16AF 1.1/8AF 1.3/16AF 1.1/4AF

+ 1987 1990-125 1990-250

) 1995 1985

5.65

T !

19 TMU / TAU-10T SOCKET SETS 1/2"27 pieces


T

36

SOCKETS


612456 C19 TMZ ! 1993 Z-94 8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26 -1.27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4

+ 1987 1990-125 1990-250

) 19951985

5.48

614831 D19 TMZ ! 1993 Z-94 8 10 11 12 13 14 15 16 17 19 21 22 23 24 26 27 28 30 32

+ 1987 1990-125 1990-250

) 1995 1985

5.56

614572 D19 TMA-Z ! 1993 Z-94 10 13 14 15 16 17 19 22 24 27 30 32 3/8AF 7/16AF 1/2AF 9/16AF 11/16AF 13/16AF 1.AF

+ 1987 1990-125 1990-250

) 1995 1985

5.42

T !

19 TMZ / TMAZ SOCKET SETS 1/2"27 pieces


T !

C19 YMAU-10T SOCKET SETS 1/2"32 pieces



612367 C19 YMAU-10T $ 1993 U-10 T 8-5/16 9-11/32 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18 19-3/4 21-13/16 22 24-15/16 26 -1.27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/47/16AF 9/16AF 7/8AF

1990-1251990-250

1997-37550-20.8 + 1987) 1995Joint

7.23

T

37

T !

D19 YMAU-10T SOCKET SET 1/2"43 pieces

› Manually operated 1/2” sockets and accessories. › Supplied in blue powder coated, D19 Y steel box. › Dimensions: 526x190x52mm.

Code No. 1B Spanners Ratchet Sockets Accessories 0

612383 C19 YM1B-10T 10 11 12 13 14 15 16 17 19 22 24 $ 1993 U-10 T 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 19-3/4 22 24-15/16

1990-125 1997-375

50-20.8 6.04

616230 D19 YM1B-10T 10 11 12 13 14 15 16 17 19 22 24 $ 1993 U-10 T 10 11 12 13 14 15 16 17 19 22 24 1990-125 1997-375

50-20.8 6.50

T ! 19 YM1B-10T




616222 D19 YMAU-10T $ 1993 U-10 T 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 27 5/16AF 11/32AF 3/8AF 13/32AF 7/16AF 1/2AF 9/16AF 19/32AF 5/8AF 11/16AF 3/4AF 25/32AF 13/16AF 7/8AF 15/16AF 1. AF

1990-125 1990-250

+ 1987-375) 1995 50-20.81985

7.39

T

38

SOCKETS

Code No. Spanners Ratchet Sockets Accessories 0

612391 C19 62MU-10T No.2 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22No.6 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22

$ 1993 U-10 T 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 20-25/32 21-13/16 22

1990-125 1990-250

+ 1987) 1995

6.76

616001 D19 62MU-10T No.2 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22No.6 6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22

$ 1993 U-10 T 10 11 12 13 14 15 16 17 18 19 20 21 22

1990-125 1990-250

+ 1987) 1995

7.12

T ! 19 62MU-10T



T ! IN19 PM-5D / PA-5D


› Manually operated 1/2” sockets. › Supplied in black matt-�nish insert.

T ! IN19 PM-6 / PA-6


› Manually operated 1/2” sockets. › Supplied in black matt-�nish insert. › Also available in a blister pack.

Code No. Sockets 0

617423 PM 5D IN19 6 8 10 12 14 IN19L 6-100 8-100 10-100 12-100 14-100

1.25

617458 PA 5D IN19 1/4AF 5/16AF 3/8AF 1/2AF 9/16AF IN19L 1/4-100 5/16-100 3/8-100 1/2-100 9/16-100

1.10

Code No. Sockets 0

617474 PM-6 IN19 5 6 8 10 12 14 1.26617849 PA-6 IN19 3/16AF 1/4AF 5/16AF 3/8AF 1/2AF 9/16AF 1.10

617476 SR PM-6 IN19 5 6 8 10 12 14 (Including Holding Rail and Adaptor)

0.6

T ! INX19

SOCKET SETS 1/2"

› Manually operated 1/2” spline sockets. › Supplied in black matt-�nish insert.


T ! ITX19

TORX® SOCKET SETS 1/2"9 pieces

› Manually operated 1/2” sockets. › Supplied in blue powder coated Ref D30 K steel box. › Dimensions: 281x77x37mm. › Also available in a blister pack.

Code No. Sockets 0

617989 PM-5D INX19 5 6 8 10 12 INX19L 6-100 8-100 10-100 12-100 IKS19 2

1.32

617601 6 INX19-6 5 6 8 10 12 IKS19 2

0.51

Code No. Sockets 0

665983 MT ITX19 T20 T25 T27 T30 T40 T45 T50 1.00665986 SR-MT ITX19 T20 T25 T27 T30 T40 T45 T50

(Including Holding Rail and Adaptor)

0.54

Registered trademark of Acument Intellectual Properties, LLC. USA.

T

39

Code No. Sockets 0

615625 PM-9 IN19 5 6 7 8 9 10 12 14 17 1.50615641 PA-9 IN19 3/16AF 7/32AF 1/4AF 9/32AF 5/16AF 3/8AF

1/2AF 9/16AF 5/8AF1.47

615627 SR-PM9 IN19 5 6 7 8 9 10 12 14 17 (Including Holding Rail and Adaptor)

0.96

T ! IN19 PM-9 / PA-9


› Manually operated 1/2” sockets. › Supplied in blue powder coated Ref D30 K steel box. › Dimensions: 281x77x37mm. › Also available in a blister pack.

Code No. Sockets 0

617415 PM-10 IN19 5 6 7 8 9 10 12 14 17 19 1.26617431 PA-10 IN19 3/16AF 7/32AF 1/4AF 5/16AF 3/8AF

1/2AF 9/16AF 5/8AF 9/32AF IKS19 2

1.10

617417 SR-PM10 IN19 5 6 7 8 9 10 12 14 17 19 (Including Holding Rail and Adaptor)

1.22

T ! IN19 PM-10 / PA-10


› Manually operated 1/2” allen key sockets. › Supplied in black matt-�nish insert.


Code No. Sockets 0

665991 FT TX19 E10 E11 E12 E14 E16 E18 E20 E24 0.51665994 SR-FT TX19 E10 E11 E12 E14 E16 E18 E20 E24

(Including Holding Rail and Adaptor)0.62

TORX® = Registered trademark of Acument Intellectual Properties, LLC. USA

T

40

SOCKETS

Code No. 514640 D 19 J Box514632 D 19 K Box514667 D 19 T Box514675 D 19 Y Box515450 C 19 Y Insert515965 D 19 GM Insert515485 D 19 H Insert515975 D 19 IM Insert544191 D 19 J Insert515507 D 19 K Insert544213 D 19 T Insert515310 D 19 T 97 Insert515515 D 19/22 T Insert544221 D 19 Y Insert515337 D 19 YM1B Insert544205 D 19 1B Insert515353 D 19 62MU Insert515426 IN19 - 5D Insert515418 IN19 - 6 Insert544248 IN19 - 9 Insert515396 IN19PM - 10 Insert515876 ITX19 MT Insert515868 TX19 FT Insert515841 ITX/TX19 FM Insert515981 K19 Insert

T !

ITX / TX19 FMT TORX® SOCKET SET 1/2"17 pieces

› Manually operated 1/2” sockets. › Supplied in blue powder coated, D19 J steel box. › Dimensions: 290x186x52mm.

T !

TX19 SOCKET SETS 1/2"10 pieces

› Manually operated 1/2” sockets. › Supplied in blue powder coated, D30 K steel box. › Dimensions: 281x77x37mm. › Also available in a blister pack.

SPARES

› Blue powder coated steel case. › Black matt-�nish insert.

19 REPAIR KITS

19 BOXES & INSERTS

› For the 1993Z ratchet and 1996/7 power bar.

Code No.

545694 1993 Z Repair Kit545708 1996/7 Repair Kit

Code No. Sockets 0

666009 FMT ITX19 T20 T25 T27 T30 T40 T45 T50TX19 E10 E11 E12 E14 E16 E18 E20 E24

1.10

Ratchets (1/2")

1993 U-10 T REVERSIBLE RATCHET 1/2"

› For manually operated sockets and accessories with 1/2” square drive. › In accordance with SANS 1113 and DIN 3122. › With recessed lever change. › Push-button release. › Return angle of seven and a half degrees.

› Non-slip 2-component handle. › Locks in the middle position: When the lever is

�ipped, it automatically engages for clockwise or anti-clockwise operation. › Chrome Vanadium steel 31CrV3. › Ball locking device.

Code No. a „ a A° y

614262 1993U-10T 1/2 12.5 7,5 270

1993 U-10 K PLASTIC RATCHET 1/2"

› Maximum torque: 70Nm. › For manually operated sockets and accessories with 1/2” square drive. › Return angle of seven and a half degrees. › Made from sturdy compound material with a steel mechanism. › Lightweight. › Dimensions: 44 x 145 x 42.2mm. › Reversible ratchet.


624489 1993U-10K 1/2 12.5 7,5 145 0.226


› For manually operated sockets and accessories with 1/2” square drive. › With recessed lever change. › Ball locking device. › Return angle of �ve degrees.

› Non-slip 2-component handle. › In accordance with SANS 1113 and DIN 3122. › Chrome Vanadium steel 31CrV3.


614424 1993U-3 1/2 12.5 5 270 0.544

1993 Z-94 RATCHET HANDLE WITH COUPLER 1/2" › For manually operated sockets and accessorieswith 1/2” square drive. › With square coupler, medium-�ne toothed, extremely rugged › Return angle of seven and a half degrees. › Reversible ratchet. › Non-slip 2-component handle › In accordance with SANS 1113 and DIN 3122. › Chrome Vanadium steel 31CrV3.


614459 1993Z-94 1/2 12.5 7,5 270 0.430

T

41

3 3

Code ! y 0

612006 C19 8mm-5/16 38.0 0.056612014 C19 9mm-11/32 38.0 0.054612022 C19 10mm-3/8 38.0 0.055612030 C19 11mm 38.0 0.057612057 C19 12mm 38.0 0.058612065 C19 13mm-1/2 38.0 0.057612073 C19 14mm 38.0 0.059612081 C19 15mm-19/32 40.0 0.065612103 C19 16mm-5/8 40.0 0.065612111 C19 17mm 40.0 0.073612138 C19 18mm-11/16 40.0 0.062612146 C19 19mm-3/4 40.0 0.078612154 C19 20mm-25/32 40.0 0.084612162 C19 21mm-13/16 41.5 0.096612170 C19 22mm 41.5 0.099612189 C19 23mm 41.5 0.121612197 C19 24mm-15/16 41.5 0.124612200 C19 25mm 41.5 0.130612219 C19 26mm-1. 41.5 0.135612227 C19 27mm-1.1/16 41.5 0.145612235 C19 28mm 43.0 0.148612243 C19 29mm-1.1/8 43.0 0.159612251 C19 30mm-1.3/16 43.0 0.175612278 C19 32mm-1.1/4 43.0 0.189

612308 C19 7/16AF 38.0 0.056612324 C19 9/16AF 38.0 0.061612375 C19 7/8AF 41.5 0.105

Code ! y 0

613304 D19 8mm 38.0 0.056613312 D19 9mm 38.0 0.053613320 D19 10mm 38.0 0.055613339 D19 11mm 38.0 0.055613347 D19 12mm 38.0 0.057613355 D19 13mm 38.0 0.057613363 D19 14mm 38.0 0.061613371 D19 15mm 40.0 0.065613398 D19 16mm 40.0 0.072613401 D19 17mm 40.0 0.067613428 D19 18mm 40.0 0.065613436 D19 19mm 40.0 0.074613444 D19 20mm 40.0 0.088613452 D19 21mm 41.5 0.096613460 D19 22mm 41.5 0.100613479 D19 23mm 41.5 0.111613487 D19 24mm 41.5 0.122613495 D19 25mm 41.5 0.135613509 D19 26mm 41.5 0.140613517 D19 27mm 41.5 0.145613525 D19 28mm 43.0 0.167613533 D19 29mm 43.0 0.170613541 D19 30mm 43.0 0.190613576 D19 32mm 43.0 0.219613584 D19 33mm 44.5 0.250613568 D19 36mm 44.5 0.287

613606 D19 5/16AF 38.0 0.054613614 D19 11/32AF 38.0 0.051613622 D19 3/8AF 38.0 0.053613630 D19 13/32AF 38.0 0.054613649 D19 7/16AF 38.0 0.053613657 D19 1/2AF 38.0 0.055613665 D19 9/16AF 38.0 0.063613673 D19 19/32AF 40.0 0.065613681 D19 5/8AF 40.0 0.070613703 D19 11/16AF 40.0 0.062613711 D19 3/4AF 40.0 0.077613738 D19 25/32AF 40.0 0.082613746 D19 13/16AF 41.5 0.098613754 D19 7/8AF 41.5 0.100613762 D19 15/16AF 41.5 0.120613770 D19 1. AF 41.5 0.137613789 D19 1.1/16AF 41.5 0.145613797 D19 1.1/8AF 43.0 0.167613800 D19 1.3/16AF 43.0 0.190613819 D19 1.1/4AF 43.0 0.203

T

INK19 IMPACT ALLEN KEY SOCKETS 59

42

SOCKETS

Sockets (1/2")

T C 19 (MM) / (AF) SOCKETS 1/2"C profile

› Manually operated sockets with thin walls and knurled base. › CHROME VANADIUM steel – 31CrV3. › Chrome plated and polished. › In accordance with SANS 1113 and DIN 3124.

T

D 19 (MM) / (AF) SOCKETS 1/2“bi-hexagon UD profile

› Manually operated sockets with thin walls and knurled base. › CHROME VANADIUM steel – 31CrV3. › Chrome plated and polished. › In accordance with SANS 1113 and DIN 3124.

K19 IMPACT SOCKETS 58

Code ! y 0

615315 IN19 5mm 60 0.050615323 IN19 6mm 60 0.055615331 IN19 7mm 60 0.058615358 IN19 8mm 60 0.060615366 IN19 9mm 60 0.063615374 IN19 10mm 60 0.065615382 IN19 12mm 60 0.075615390 IN19 14mm 60 0.085615404 IN19 17mm 60 0.115615412 IN19 19mm 60 0.120

Code ! y 0

015705 D19L 10mm 82 0.095015706 D19L 12mm 82 0.120015701 D19L 13mm 82 0.100015702 D19L 14mm 82 0.130015707 D19L 15mm 82 0.130015712 D19L 16mm 82 0.140015703 D19L 17mm 82 0.150015708 D19L 18mm 82 0.180015704 D19L 19mm 82 0.190015709 D19L 21mm 82 0.210015713 D19L 22mm 82 0.210015710 D19L 24mm 82 0.260015711 D19L 27mm 82 0.310015714 D19L 30mm 82 0.300015715 D19L 32mm 82 0.400

Code ! y 0

614017 19L 13mm 77 0.102614025 19L 14mm 77 0.109614033 19L 17mm 77 0.134614041 19L 19mm 82 0.171614068 19L 21mm 82 0.205614076 19L 24mm 82 0.250

614130 19L 1/2AF 77 0.96614149 19L 9/16AF 77 0.110614157 19L 5/8AF 77 0.130614165 19L 11/16AF 77 0.143614173 19L 3/4AF 82 0.173614181 19L 13/16AF 82 0.210614203 19L 7/8AF 82 0.213614211 19L 15/16AF 82 0.233

19L (MM) / (AF) SOCKETS 1/2"hexagon, long pattern

T

› Manually operated sockets with knurled base. › For hexagon head screws. › 1/2” square drive. › Bits: Chrome Vanadium steel 59CrV4. › Sockets: Chrome Vanadium steel 31CrV3.

IN 19 (MM) / (AF) SCREWDRIVER BIT SOCKETS 1/2"for hexagon screws

Code ! y 0

615471 IN19 3/16AF 60 0.050615498 IN19 7/32AF 60 0.053615501 IN19 1/4AF 60 0.055615528 IN19 9/32AF 60 0.055615536 IN19 5/16AF 60 0.060615544 IN19 3/8AF 60 0.065615552 IN19 1/2AF 60 0.080615560 IN19 9/16AF 60 0.085615579 IN19 5/8AF 60 0.115

T

43

T

› Manually operated sockets with thin walls and knurled base. › Chrome Vanadium steel 31CrV3. › 1/2” square drive. › Chrome plated and polished.

D19L (MM) SOCKETS 1/2"bi-hexagon UD profile, long pattern

T

› Manually operated sockets with thin walls and knurled base. › Chrome Vanadium steel 31CrV3. › 1/2” square drive. › Chrome plated and polished.

Code ! y 0

6162060 IN19L 5-90 90 0.091615730 IN19L 6-100 100 0.0796157570 IN19L 7-100 100 0.089615773 IN19L 8-100 100 0.097615811 IN19L 10-100 100 0.124615846 IN19L 12-100 100 0.151615862 IN19L 14-100 100 0.202616265 IN19L 1/4-100 100 0.081616303 IN19L 5/16-100 100 0.097616346 IN19L 3/8-100 100 0.119616370 IN19L 1/2-100 100 0.161616397 IN19L 9/16-100 100 0.207

Code ! y 0

1449826 INR 19L 5-100 100 0.0851449850 INR 19L 6-100 100 0.0851449877 INR 19L 8-100 100 0.0851449591 INR 19L 10-100 100 0.1051398636 INR 19L 12-100 100 0.1451449893 INR 19L 14-100 100 0.155

› Manually operated sockets with knurled base. › For hexagon head screws. › 1/2” square drive. › Bits: Chrome Vanadium steel 59CrV4. › Sockets: Chrome Vanadium steel – 31CrV3.

T

› Manually operated sockets with knurled base. › For hexagon head screws. › 1/2” square drive. › Bits: Chrome Vanadium steel 59CrV4. › Sockets: Chrome Vanadium steel 31CrV3.

T

› Manually operated sockets with knurled base. › Chrome Vanadium steel 31CrV3. › 1/2” square drive. › Bits: Molybdenum tool steel.

T

› Chrome Vanadium steel 31CrV3. › 1/2” square drive. › Manually operated sockets with knurled base. › Bits: Molybdenum tool steel.

T

INR 19 L SCREWDRIVER BIT SOCKETS 1/2"for multi-spline screws RIBE®, long pattern

IN 19 L SCREWDRIVER BIT SOCKETS 1/2"for hexagon screws, long pattern

INX 19-INX 19L SCREWDRIVER BIT SOCKETS 1/2"for multi-point screws XZN

ITX 19 SCREWDRIVER BIT SOCKETS 1/2"for recessed TORX® head screws


Code !

+ y 0

024710 ITX19 T 20 T20 M4-M5 3.86 55 0.068024720 ITX19 T 25 T25 M4,5-M5 4.43 55 0.070024730 ITX19 T 27 T27 M4.5-M6 4.99 55 0.070024740 ITX19 T 30 T30 M6-M7 5.52 55 0.070024750 ITX19 T 40 T40 M7-M8 6.65 55 0.075024760 ITX19 T 45 T45 M8-M10 7.82 55 0.070024770 ITX19 T 50 T50 M10 8.83 55 0.075024780 ITX19 T 55 T55 M12 11.22 55 0.100024790 ITX19 T 60 T60 M14 13.25 55 0.110

Code ! + y 0

615889 INX19L 5mm M5 55 0.068615900 INX19L 6mm M6 55 0.076615927 INX19L 8mm M8 55 0.077615943 INX19L 10mm M10 55 0.094615978 INX19L 12mm M12 55 0.110615919 INX19L 6-100 M6 100 0.093615935 INX19L 8-100 M8 100 0.097615951 INX19L 10-100 M10 100 0.124615986 INX19L 12-100 M12 100 0.1491888951 INX19L 14-100 M14 100 0.110

RIBE® = Registered trademark of Richard Bergner, GmbH & Co. KG, Schwabach, Germany.

T

44

SOCKETS

IKS 19 SCREWDRIVER BIT SOCKETS 1/2"for cross-head screws PH

ITX 19 L SCREWDRIVER BIT SOCKETS 1/2"for recessed TORX® head screws, long pattern

TX 19 SOCKETS 1/2"for protruding TORX® head screws

ITX 19 B SCREWDRIVER BIT SOCKETS 1/2"for recessed TORX® head screws with pilot

› Manually operated sockets with thin walls and knurled base. › Chrome Vanadium steel 31CrV3. › 1/2” square drive. › Chrome plated.

› Manually operated sockets with knurled base. › 1/2” square drive. › Sockets: Chrome Vanadium steel 31CrV3. › Bits: Molybdenum tool steel. › Socket with Phillips & POZZIDRIV® Bits

› Manually operated sockets with knurled base. › Chrome Vanadium steel 31CrV3. › Bits: Molybdenum tool steel. › 1/2” square drive. › Tamper proof.

› Manually operated sockets with knurled base. › 1/2” square drive. › Chrome Vanadium steel 31CrV3. › Bits: Molybdenum tool steel.

T

T

T

T

Code NO. 9 + y 0

665908 TX19 E 10 E10 M8 9.42 38.0 0.055665916 TX19 E 11 E11 - 10.08 38.0 0.055665924 TX19 E 12 E12 M10 11.17 38.0 0.055665932 TX19 E 14 E14 M12 12.90 38.0 0.055665940 TX19 E 16 E16 M12 14.76 38.0 0.060665959 TX19 E 18 E18 M14 16.70 40.0 0.080665967 TX19 E 20 E20 M6 18.45 40.0 0.085665975 TX19 E 24 E24 M18-M20 22.16 41.5 0.115

Code ! 9 + & y 0

024210 ITX19L T20 T20 M4-M5 3.86 100 0.095024215 ITX19L T25 T25 M4.5-M5 4.43 100 0.095024220 ITX19L T27 T27 M4.5-M6 4.99 100 0.096024225 ITX19L T30 T30 M6-M7 5.52 100 0.096024230 ITX19L T40 T40 M7-M8 6.65 100 0.096024235 ITX19L T45 T45 M8-M10 7.82 100 0.098024240 ITX19L T50 T50 M10 8.83 100 0.124024245 ITX19L T55 T55 M12 11.22 100 0.151024250 ITX19L T60 T60 M14 13.25 100 0.197024253 ITX19L T70 T70 M16 15.55 100 0.277

Code ! y 0

665665 IKS19 NO. 2 60 0.075665673 IKS19 NO. 3 60 0.080665711 IKS19 PZD 2 60 0.070665738 IKS19 PZD 3 60 0.080

T


TORX® = Registered trademark of Acument Intellectual Properties, LLC. USA. TORX® = Registered trademark of Acument Intellectual Properties, LLC. USA.

45

Code !

8 + y 0

6192720 ITX19B T20* T20 M4-M5 3.86 55 0.0756195660 ITX19B T25* T25 M4,5-M5 4.43 55 0.0756196390 ITX19B T27* T27 M4,5-M6 4.99 55 0.0766200170 ITX19B T30 T30 M6-M7 5.52 55 0.0766200410 ITX19B T40 T40 M7-M8 6.65 55 0.091

*WHILE STOCKS LAST

Accessories (1/2")


614335 1985 1/2 12.5 420 0.585


614483 1996 1/2 12.5 255 0.414614491 1997/375 1/2 12.5 375 0.576614556 1997/450 1/2 12.5 450 0.677

Code No. Q „

Q a „

a y 0

6143000 1930 1/2 12,5 3/8 10 39 0.062

1/2“ 3/8“12,5 mm 10 mm

1930 REDUCER 1/2" TO 3/8"


3/4“1/2“20 mm12,5 mm

1932 CONVERTER 1/2" TO 3/4"


Code No. a „

a Q „

Q y 0

614319 1932 3/4 20 1/2 12.5 45 0.124

1985 SPEED BRACE HANDLE 1/2"

› For manually operated sockets and accessories with 1/2” square drive. › Chrome Vanadium steel 31CrV3.

1996 - 1997 SWIVEL HANDLES 1/2"

› For manually operated sockets and accessories with 1/2” square drive. › Non-slip 2-component handle. › In accordance with SANS 1113 and DIN 3122. › Chrome Vanadium steel 31CrV3.

1997

1996

T

46

SOCKETS


614378 1990/75 1/2 12.5 75 0.109614386 1990/125 1/2 12.5 125 0.177614289 1990/175 1/2 12.5 175 0.239614394 1990/250 1/2 12.5 250 0.337

› For manually operated sockets and accessories with 1/2” square drive. › Chrome Vanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3123. › For manually operated sockets and accessories with 1/2” square drive and ball locking device.

› Strong magnet securely �xes even large screws in the socket. › Makes work easier particularly in con�ned spaces. › One-hand operation. › Chrome Vanadium steel 31CrV3. › In accordance with DIN 3120. › Hot forged.

Code No. a „

a Q „

Q y 0

614475 1995 1/2 12.5 1/2 12.5 70 0.149Code No. a

„a y 0

2697920 1990M 1/2 12.5 83 0.110


› For manually operated sockets and accessories with 1/2” square drive. › Chrome Vanadium steel 31CrV3.

Code No. a „

a y 0

614343 1987 1/2 12.5 290 0.350

Code No. a „

a y 0

6144670 1994 Coupler 1/2 12.5 37 0.042614467 1994 PZK* 1/2 12.5 46 0.056

1990-75

1990-125

1990-2501990-175

1990 EXTENSION BARS 1/2"



1990 M EXTENSION 1/2"with magnet

1987 SLIDING T-BAR 1/2"

1994 COUPLERS 1/2"

T

47

*WITH MUSHROOM HEAD

32 EMAZ/ EMZ / EAZ SOCKET SETS 3/4"16 pieces

› Manually operated 3/4” sockets and accessories. › Supplied in blue powder coated D32 E steel box. › Dimensions: 526x190x75mm.


626546 C32 EMAU-2 " 3293 U-2 C32 27-1.1/16 29-1.1/8 32-1.1/4 33-1.5/16 36-1.7/16 38-1.1/2 41-1.5/8 46-1.13/16 50-2. 1.3/8AF

+3287 3290-200 3290-400

11.60

628042 D32 EMU-2 " 3293 U-2 D32 22 24 27 30 32 36 38 41 46 50

+ 3287 3290-200 3290-400

11.23

628069 D32 EAU-2 " 3293 U-2 D32 7/8 15/16 1.1/16 1.1/4 1.5/16 1.3/8 1.7/16 1.5/8 1.13/16 2.

+ 3287 3290-200 3290-400

11.40

32 EMAU-2 / EMU-2 SOCKET SETS 3/4"16 pieces

e !

e !

› Manually operated 3/4” sockets and accessories. › Supplied in blue powder coated D32 E steel box. › Dimensions: 526x190x75mm.


626538 C32 EMAZ ! 3293 Z-94 C32 27-1.1/16 29-1.1/8 32-1.1/4 33-1.5/16 36-1.7/16 38-1.1/2 41-1.5/8 46-1.13/16 50-2. 1.3/8AF

+ 3287 3290-200 3290-400

11.43

628026 D32 EMZ ! 3293 Z-94 D32 22 24 27 30 32 36 38 41 46 50

+ 3287 3290-200 3290-400

11.06

628050 D32 EAZ ! 3293 Z-94 D32 7/8AF 15/16AF 1.1/16AF 1.1/4AF 1.5/16AF 1.3/8AF 1.7/16AF 1.5/8AF 1.13/16AF 2.AF

+ 3287 3290-200 3290-400

11.22

(3/4") Square Drive

Sets (3/4")

U

48

SOCKETS

Ratchets (3/4")


627798 3293 U-1 3/4 20 11,25 500 2.59627984 3293 U-1/440 3/4 20 11,25 440 2.38

› For manually operated sockets and accessories with 3/4” square drive. › Chrome Vanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3122. › With lever control and detachable handle.


627860 3293 U-2 3/4 20 7,2 500 1.47



627895 3293 Z-94 3/4 20 10 500 1.30



3293 Z-94 RATCHET HANDLE WITH COUPLER 3/4"

3293 U-1 REVERSIBLE RATCHETS WITH LEVER CONTROL 3/4"

U

49

Code ! y 0

626007 C32 19mm-3/4 51.5 0.208626015 C32 22mm-7/8 51.5 0.211626023 C32 24mm-15/16 51.5 0.221626058 C32 26 mm-1. 51.5 0.220626066 C32 27mm-1.1/16 54.5 0.243626074 C32 29mm-1.1/8 54.5 0.261626082 C32 30mm-1.3/16 57.5 0.303626090 C32 32mm-1.1/4 57.5 0.343626104 C32 33mm-1.5/16 57.5 0.350626112 C32 34mm 57.5 0.380626171 C32 36mm-1.7/16 59.5 0.413626201 C32 38mm-1.1/2 59.5 0.440626228 C32 41mm-1.5/8 62.5 0.550626244 C32 46mm-1.13/16 65.5 0.690626260 C32 50mm-2. 68.5 0.840

626279 C32 1.3/8AF 59.5 0.402

Code ! y 0

627216 D32 19mm 51.5 0.208627224 D32 22mm 51.5 0.211627232 D32 24mm 51.5 0.221627240 D32 27mm 54.5 0.243627259 D32 29mm 54.5 0.261627267 D32 30mm 57.5 0.303627275 D32 32mm 57.5 0.343627704 D32 33mm 57.5 0.350627763 D32 34mm 57.5 0.380627283 D32 36mm 59.5 0.413627291 D32 38mm 59.5 0.439627305 D32 41mm 62.5 0.551627313 D32 46mm 65.5 0.690627321 D32 50mm 68.5 0.780

627402 D32 7/8AF 51.5 0.212627410 D32 15/16AF 51.5 0.222627429 D32 1. AF 51.5 0.220627437 D32 1.1/16AF 54.5 0.250627445 D32 1.1/8AF 54.5 0.240627399 D32 1.3/16AF 58.0 0.306627453 D32 1.1/4AF 57.5 0.331627461 D32 1.5/16AF 57.5 0.370627488 D32 1.3/8AF 59.5 0.402627496 D32 1.7/16AF 59.5 0.440627518 D32 1.1/2AF 59.5 0.435627526 D32 1.5/8AF 62.5 0.551627534 D32 1.11/16AF 62.5 0.600627542 D32 1.3/4AF 65.5 0.550627550 D32 1.13/16AF 65.5 0.690627569 D32 1.7/8AF 65.5 0.765627577 D32 2.AF 68.5 0.840


627127 3293/500 3/4 20 15 625 3.08627194 3293/500 24x30 3/4 20 15 650 2.94

› For manually operated sockets and accessories with 3/4” square drive. › Chrome Vanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3122. › 500 DJ with double 3/4” drive coupler and 500mm detachable handle. › 500 DJ24x30 with 24mm and 30mm �xed sockets and 500mm detachable handle.

3293/500 DJ/DJ 24X34 DOUBLE JOHNNY RATCHETS 3/4"

3293/500

3293/500-24x30

U

K32 IMPACT SOCKETS 60

50

SOCKETS

Sockets (3/4")

C 32 (MM) / (AF) SOCKETS 3/4"C profile

› Manually operated sockets with thin walls and knurled base. › Chrome Vanadium steel 31CrV3. › Chrome plated. › In accordance with SANS 1113 and DIN 3124.

D 32 (MM) / (AF) SOCKETS 3/4“bi-hexagon UD profile

› Manually operated sockets with thin walls and knurled base. › Chrome Vanadium steel 31CrV3.. › Chrome plated. › In accordance with SANS 1113 and DIN 3124.

U

U

Accessories (3/4")

U

IN32 14mm

IN32 22mm

IN 32 SCREWDRIVER BIT SOCKETS 3/4"for hexagon head screws

› Manually operated sockets with knurled base. › 3/4” square drive. › Sockets: Chrome Vanadium steel 31CrV3. › Bits: Chrome Vanadium steel 59CrV4.

Code No. $ y 0

6275850 IN32 14mm 14 80 0.3526275930 IN32 17mm 17 80 0.394

Code No. $ y 0

6276070 IN32 19mm 19 80 0.4336276150 IN32 22mm 22 80 0.482

3296 SWIVEL HANDLE 3/4"


3287 SLIDING T BARS 3/4"


627925 3296 3/4 20 547 1.90


627836 3287 3/4 20 500 0.118627941 3287/447 3/4 20 447 0.107


3290-200



627844 3290/200 3/4 20 200 0.555627852 3290/400 3/4 20 400 1.058


U

51

3/4“ 1/2“20 mm 12,5 mm

1“3/4“25 mm20 mm

3219 REDUCER 3/4" TO 1/2"

3221 CONVERTER 3/4" TO 1"



Code No. a „

a Q „

Q y 0

017100 3219 1/2 12,5 3/4 20 56 0.160Code No. a

„a Q

„Q y 0

627828 3221 1 25 3/4 20 60 0.338

Code No. a „

a Q „

Q y 0

017170 3295 3/4 20 3/4 20 105 0.580Code No. a

„a y 0

627909 3294 3/4 20 52 0.133

U

52

SOCKETS


3294 COUPLER 3/4"



SPARES

› Blue powder coated steel case. › Black matt-�nish insert.

32 REPAIR KITS 19 BOXES & INSERTS

› For the 3293 range of ratchets and 3296 power bar.

Code No.

541036 3293 U-I Repair Kit545716 3293 U-2 Repair Kit545724 3293 Z Repair Kit627135 3293 DJ Repair Kit545740 3296 Repair Kit

Code No.

514683 D32 E Box544256 D32 Insert545228 C32 EMAZ Insert

f !

D 21 EMU-10 SOCKET SET 1"15 pieces

› Manually operated 1” sockets and accessories. › Gedore Vanadium steel 31CrV3. › With reversible lever change ratchet. › Supplied in blue powder coated steel case. › Dimensions: 760 x 260 x 105mm.


018250 D 21 EMU JG $ 2193 U-3 3 D 21 36 41 46 50 55 60 65 70 75 80

2190 -16 Extension 2190 -8 Extension

+ 2187 Sliding T-Bar

27.60

2193 U-3 REVERSIBLE RATCHET 1" › In accordance with SANS 1113 and DIN 3122. › Chrome Vanadium steel 31CrV3. › With non-slip metal disc change, �ne-toothed

(72 teeth) and robust. › Return angle 5 degrees. › Push-�t tube handle. › For manually operated sockets and accessories

with 1” square drive.

2193 Z-94 RATCHET HANDLE WITH COUPLER 1"


018240 2193 U-3 1 25 5 720 4.5


6181520 2193 Z-94 1 25 9 720 4.2

› In accordance with SANS 1113 and DIN 3122. › Chrome Vanadium steel 31CrV3. › With non-slip metal disc change, �ne-toothed

(72 teeth) and robust. › Return angle of nine degrees. › Push-�t tube handle. › For manually operated sockets and accessories

with 1” square drive.

53

(1") Square Drive

Sets (1")

V

36-65mm

70-80mm

Code ! y 0

018001 D21 36mm 70 0.600018002 D21 41mm 70 0.700018003 D21 46mm 75 0.900018004 D21 50mm 75 1.000018005 D21 55mm 75 1.100

V

Sockets (1")

D 21/21 (MM) SOCKETS 1"C profile

› Manually operated sockets with knurled base. › 1” square drive. › Gedore Vanadium steel 31CrV3. › Chrome plated. › In accordance with SANS 1113 and DIN 3124.

Code ! y 0

018006 D21 60mm 80 1.200018011 D21 65mm 84 1670018008 D21 70mm - Hexagon 70 0.600018009 D21 75mm - Hexagon 70 0.700018010 D21 80mm - Hexagon 75 0.900

2187 SLIDING T-BAR 1" › For manually operated sockets and accessories with 1” square drive. › Chrome Vanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3122.

Code No. a „

a y 0

018210 2187 1 25 640 3.100

Accessories (1")

54

SOCKETS V

1‘ IMPACT ACCESSORIES 63 IMPACT SOCKET SETS 58

1“ 3/4“25 mm 20 mm

2190-16

2190 EXTENSIONS 1"

2195 UNIVERSAL JOINT 1"

2194 COUPLER 1"

2132 REDUCER 1" TO 3/4"

2190-8


018220 2190-8“ 1 25 200 1.10018230 2190-16“ 1 25 400 1.90

› For manually operated sockets and accessories with 1” square drive. › Chrome Vanadium steel 31CrV3. › In accordance with SANS 1113 and DIN 3122.


Code No. a „

a Q „

Q y 0

018200 2132 3/4 25 1 20 75 0.500



Code No. a „

a y 0

6180710 2194 1 25 68 0.321Code No. a

„a Q

„Q y 0

6180980 2195 1 25 1 25 140 1.48

55

V

56

IMPACT TOOLS

IMPACT SOCKETS, SETS

ACCESSORIES

(1/2”) SOCKETS

58

(3/4”) SOCKETS

60

(1”) ACCESSORIES

63

(1/2”) SETS

58

(3/4”) ACCESSORIES

61

(1.1/2”) SOCKETS

63


59

(1”) SOCKETS

62

(1.1/2”) ACCESSORIES

63

Impact Tools

(1/2") square drive

T

Code ! Recommended Accessories y 0

6160280 K19 10mm KB1970 10-14, KB1975 10-14 38 0.0826160360 K19 11mm KB1970 10-14, KB1975 10-14 38 0.0856160440 K19 12mm KB1970 10-14, KB1975 10-14 38 0.0846160520 K19 13mm KB1970 10-14, KB1975 10-14 38 0.0816160600 K19 14mm KB1970 10-14, KB1975 10-14 38 0.0826160790 K19 16mm KB1970 15-27, KB1975 15-27 38 0.1246160870 K19 17mm KB1970 15-27, KB1975 15-27 38 0.1236160950 K19 18mm KB1970 15-27, KB1975 15-27 38 0.1226161090 K19 19mm KB1970 15-27, KB1975 15-27 38 0.1196161170 K19 21mm KB1970 15-27, KB1975 15-27 38 0.1376161250 K19 22mm KB1970 15-27, KB1975 15-27 38 0.1426161330 K19 23mm KB1970 15-27, KB1975 15-27 38 0.1486161410 K19 24mm KB1970 15-27, KB1975 15-27 45 0.1546182680 K19 27mm KB1970 15-27, KB1975 15-27 50 0.1806182720 K19 28mm KB1970 15-27, KB1975 15-27 50 0.1836182880 K19 29mm KB1970 15-27, KB1975 15-27 50 0.1881560557 K19 30mm KB1970 15-27, KB1975 15-27 50 0.2561783742 K19 32mm KB1970 15-27, KB1975 15-27 50 0.286

K 19 (MM) IMPACT SOCKETS 1/2"hexagon

› 1/2“ square drive. › Machine-operated, suitable for all standard electric and air tools › In accordance with DIN 3129. › GEDORE special steel, manganese phosphated.

T K 19 L IMPACT SOCKETS 1/2"hexagon, long pattern

› 1/2“ square drive. › Machine-operated, suitable for all standard electric and air tools. › In accordance with DIN 3129. › GEDORE special steel, manganese phosphated.

T


6163380 K19L 10mm KB1970 10-14, KB1975 10-14 77 0.1406163381 K19L 11mm KB1970 10-14, KB1975 10-14 77 0.1336163400 K19L 12mm KB1970 10-14, KB1975 10-14 77 0.1406163540 K19L 13mm KB1970 10-14, KB1975 10-14 77 0.1506163620 K19L 14mm KB1970 10-14, KB1975 10-14 77 0.1546197790 K19L 16mm KB1970 15-27, KB1975 15-27 77 0.1726163890 K19L 17mm KB1970 15-27, KB1975 15-27 80 0.2006197870 K19L 18mm KB1970 15-27, KB1975 15-27 82 0.2156164000 K19L 19mm KB1970 15-27, KB1975 15-27 82 0.2256162730 K19L 21mm KB1970 15-27, KB1975 15-27 82 0.2436164270 K19L 22mm KB1970 15-27, KB1975 15-27 82 0.2906199810 K19L 23mm KB1970 15-27, KB1975 15-27 82 0.2926164430 K19L 24mm KB1970 15-27, KB1975 15-27 82 0.3146164780 K19L 27mm KB1970 15-27, KB1975 15-27 82 0.3896184270 K19L 30mm KB1970 15-27, KB1975 15-27 82 0.453

K 19 IMPACT SOCKET SET 1/2"5 pieces

› 5 impact sockets, machine-operated, suitable for all standard electric and air tools. › 1/2” square drive. › Supplied in blue powder coated D19 steel box. › Dimensions: 281x77x46mm.

Code No. Sockets 0

1646923 K19-5 1 K19 10 13 14 17 24 0.95

T R

T

K 1900 IMPACT DRIVER SETS 1/2"12 pieces › For use on screws and bolts with slotted, cross-slotted or hexagon heads. › Supplied in blue sheetmetal case with black plastic insert. › Dimensions: 281x79x42mm.

Code No. Sockets Accessories 0

025490 K1900-613 4 6 7 8 K1900 1.22 1 2 3 2,5 3 4 5

025491 K1900-813 7 8 9 12 K1900 1.22 2 3 4 5 6 8 10

58

IMPACT TOOLS

T


6224190 IN K19 8mm KB1970 10-14, KB1975 10-14 44 0.0936224270 IN K19 10mm KB1970 10-14, KB1975 10-14 44 0.1046224350 IN K19 12mm KB1970 15-27, KB1975 15-27 50 0.1306225320 IN K19 14mm KB1970 15-27, KB1975 15-27 50 0.1486225670 IN K19 17mm KB1970 15-27, KB1975 15-27 50 0.1896225675 IN K19 19mm KB1970 15-27, KB1975 15-27 50 0.214

IN K 19 IMPACT ALLEN KEY SOCKETS 1/2"for in-hex screws


KB 1990 EXTENSIONS 1/2"for impact sockets

› For impact sockets and accessories with 1/2” square drive.

KB 1995 UNIVERSAL JOINT 1/2"for impact sockets

› For air tool operated impact sockets and accessories with 1/2” square drive.


6655100 KB1990/75 1/2 12.5 75 0.1436173180 KB1990/125 1/2 12.5 125 0.2266366570 KB1990/250 1/2 12.5 250 0.427

Code No. a „

a Q „

Q y 0

6655410 KB1995 1/2 12.5 1/2 12.5 62 0.202

KB 1932 CONVERTER 1/2" TO 3/4"for impact sockets

› With square drive as per DIN 3121.

3/4“1/2“20 mm12,5 mm

Code No. a „

a Q „

Q y 0

6650020 KB1932 3/4 20 1/2 12.5 48 0.159

Code No. y 0

024010 KB1900 123 0.580

KB 1900 IMPACT DRIVER 1/2"


KB 1970 - KB 1975 SAFETY RING AND PINfor impact sockets 1/2"

Code No. 0

6654790 KB1970/75 8-14mm 26654870 KB1970/75 15-32mm 2

59


6283600 K32L 17mm KB3270, KB3275 90 0.4906283790 K32L 19mm KB3270, KB3275 90 0.5106283870 K32L 22mm KB3270, KB3275 90 0.5606283950 K32L 24mm KB3270, KB3275 90 0.5806284090 K32L 27mm KB3270, KB3275 90 0.6306284170 K32L 30mm KB3270, KB3275 90 0.7006284250 K32L 32mm KB3270, KB3275 90 0.7406286540 K32L 33mm KB3270, KB3275 90 0.7706281660 K32L 34mm KB3270, KB3275 90 0.8006284330 K32L 36mm KB3270, KB3275 90 0.8506284332 K32L 38mm KB3270, KB3275 90 0.8806286890 K32L 41mm KB3270, KB3275 90 0.9506284336 K32L 46mm KB3270, KB3275 90 1.080


6282040 K32 17mm KB3270, KB3275 45 0.3306289990 K32 18mm KB3270, KB3275 45 0.3306282120 K32 19mm KB3270, KB3275 45 0.3316282190 K32 21mm KB3270, KB3275 46 0.3406282200 K32 22mm KB3270, KB3275 46 0.3336282210 K32 23mm KB3270, KB3275 46 0.3606282390 K32 24mm KB3270, KB3275 46 0.3496282470 K32 27mm KB3270, KB3275 48 0.3676282474 K32 28mm KB3270, KB3275 48 0.3796282476 K32 29mm KB3270, KB3275 48 0.3846282550 K32 30mm KB3270, KB3275 52 0.3956282630 K32 32mm KB3270, KB3275 52 0.4456283010 K32 33mm KB3270, KB3275 55 0.475


1956477 INK32 14mm KB3270, KB3275 59 0.4081956485 INK32 17mm KB3270, KB3275 62 0.4451956493 INK32 19mm KB3270, KB3275 64 0.4671956507 INK32 22mm KB3270, KB3275 67 0.5201956515 INK32 24mm KB3270, KB3275 67 0.555

(3/4") square drive


K 32 (MM) IMPACT SOCKETS 3/4"hexagon

U


6281580 K32 34mm KB3270, KB3275 55 0.4756282710 K32 36mm KB3270, KB3275 56 0.4826281740 K32 38mm KB3270, KB3275 59 0.5176282970 K32 40mm KB3270, KB3275 59 0.5606282980 K32 41mm KB3270, KB3275 59 0.5616282982 K32 42mm KB3270, KB3275 58 0.5826282984 K32 44mm KB3270, KB3275 62 0.6976282986 K32 46mm KB3270, KB3275 62 0.7036282988 K32 47mm KB3270, KB3275 68 0.8106282990 K32 48mm KB3270, KB3275 68 0.8276282992 K32 50mm KB3270, KB3275 68 0.8316282994 K32 55mm KB3270, KB3275 72 1.1496282996 K32 60mm KB3270, KB3275 75 1.5006282998 K32 65mm KB3270, KB3275 78 1.800

K 32 L IMPACT SOCKETS 3/4"hexagon, long pattern

› 3/4” square drive. › With square drive as per DIN 3129.

INK32 IMPACT ALLEN KEY SOCKETS 3/4"for in-hex screws

› Machine-operated, suitable for all standard electric and air tools. › With square drive as per DIN 3121.

U

60

IMPACT TOOLS

KB 3290 EXTENSIONS 3/4"for impact sockets



6675550 KB3290/175 3/4 20 175 0.8876675650 KB3290/250 3/4 20 250 0.9176675790 KB3290/12“ 3/4 20 300 1.300

KB 3290-175

KB 3290-250

KB 3290-300

KB 3270 - KB 3275 SAFETY RING AND PINfor impact sockets 3/4"

Code No. 0

6675441 KB3270/75 17-50mm 0.026675444 KB3270/75 52-60mm 0.02

KB 3221 CONVERTER 3/4" TO 1"for impact sockets


Code No. a „

a Q „

Q y 0

6671530 KB3221 1 25 3/4 20 65 0.445

1“3/4“25 mm20 mm

KB 3295 UNIVERSAL JOINT 3/4"for impact sockets


Code No. a „

a Q „

Q y 0

6676090 KB3295 3/4“ 20 3/4 20 94 0.623

KB 3219 REDUCER 3/4" TO 1/2"for impact sockets

› With square drive as per DIN 3121. › GEDORE special steel, manganese-phosphated.

3/4“ 1/2“20 mm 12,5 mm

Code No. a „

a Q „

Q y 0

6675280 KB3219 1/2“ 12,5 3/4 20 65 0.351

U

61


6183060 K21 22mm KB 2170, KB 2175 55 0.5466183140 K21 24mm KB 2170, KB 2175 55 0.5616183220 K21 27mm KB 2170, KB 2175 55 0. 5936183290 K21 29mm KB 2170, KB 2175 56 0. 6436183300 K21 30mm KB 2170, KB 2175 57 0. 6366183490 K21 32mm KB 2170, KB 2175 57 0. 6496183650 K21 33mm KB 2170, KB 2175 57 1.0016196980 K21 34mm KB 2170, KB 2175 60 0. 7336183570 K21 36mm KB 2170, KB 2175 60 0. 7816184890 K21 38mm KB 2170, KB 2175 62 0. 8586183730 K21 41mm KB 2170, KB 2175 64 0. 8306184970 K21 42mm KB 2170, KB 2175 64 0. 9006183810 K21 46mm KB 2170, KB 2175 69 1.0546183820 K21 47mm KB 2170, KB 2175 70 1.1206183822 K21 48mm KB 2170, KB 2175 71 1.2006184030 K21 50mm KB 2170, KB 2175 73 1.3056184034 K21 52mm KB 2170, KB 2175 74 1.3006184110 K21 55mm KB 2170, KB 2175 76 1.5336184380 K21 60mm KB 2170, KB 2175 82 1.8216184460 K21 65mm KB 2170, KB 2175 85 2.0406184540 K21 70mm KB 2170, KB 2175 88 2.4796184620 K21 75mm KB 2170, KB 2175 92 3.0226184700 K21 80mm KB 2170, KB 2175 97 2.8906184710 K21 85mm KB 2170, KB 2175 106 3.8526184720 K21 90mm KB 2170, KB 2175 108 3.7306184725 K21 95mm KB 2170, KB 2175 108 4.8306184730 K21 100mm KB 2170, KB 2175 115 5.6256184735 K21 105mm KB 2170, KB 2175 120 6.620


6185350 K2L 22mm KB 2170, KB 2175 100 0.9346185430 K2L 24mm KB 2170, KB 2175 100 0.9586185510 K2L 27mm KB 2170, KB 2175 100 1.0076185780 K2L 30mm KB 2170, KB 2175 100 1.0766185860 K2L 32mm KB 2170, KB 2175 100 1.1356197950 K2L 33mm KB 2170, KB 2175 100 1.1236197010 K2L 34mm KB 2170, KB 2175 100 1.1696185940 K2L 36mm KB 2170, KB 2175 100 1.2216186080 K2L 38mm KB 2170, KB 2175 100 1.3256186160 K2L 41mm KB 2170, KB 2175 100 1.3936186240 K2L 46mm KB 2170, KB 2175 100 1.6216186242 K2L 50mm KB 2170, KB 2175 100 1.9476186244 K2L 55mm KB 2170, KB 2175 100 2.1006186246 K2L 60mm KB 2170, KB 2175 100 2.2536186248 K2L 65mm KB 2170, KB 2175 100 2.7236186250 K2L 70mm KB 2170, KB 2175 100 3.0056186252 K2L 75mm KB 2170, KB 2175 100 3.303


1956548 INK21 17mm KB 2170, KB 2175 75 0.8001956558 INK21 19mm KB 2170, KB 2175 75 0.8251956566 INK21 22mm KB 2170, KB 2175 75 0.8451956574 INK21 24mm KB 2170, KB 2175 75 0.8881956582 INK21 27mm KB 2170, KB 2175 75 0.938

V

(1") square drive

› 1“ square drive. › In accordance with DIN 3129.

K 21 (MM) IMPACT SOCKETS 1"hexagon

V

KB 2170 - KB 2175 SAFETY RING AND PINfor impact sockets 1"

Code No. 0

6657621 KB2170/75 19-70mm 0.026657623 KB2170/75 71-90mm 0.02

K 21 L IMPACT SOCKETS 1"hexagon, long pattern

› 1“ square drive. › In accordance with DIN 3121.

INK21 IMPACT ALLEN KEY SOCKETS 1"for in-hex screws

KB 2132 REDUCER 1" TO 3/4"for impact sockets

KB 2137 CONVERTER 1" TO 1.1/2"for impact sockets



› For all standard electric and air tools. › With square drive as per DIN 3121.

Code No. a „

a Q „

Q y 0

6657460 KB2132 3/4“ 20 1 25 77 0.661

Code No. a „

a Q „

Q y 0 Price6657890 KB2137 1.1/2“ 40 1 25 85 0.988 101.70

62

IMPACT TOOLS

W

(1.1/2") square drive

KB 3770 - KB 3775 SAFETY RING AND PINfor impact sockets 1.1/2"

K 37 IMPACT SOCKETS 1.1/2"hexagon

KB 3790 EXTENSIONS 1.1/2“for impact sockets


6657969 KB2190/175 1 25 200 1.576657975 KB2190/250 1 25 300 1.756658000 KB2190/330 1 25 400 2.35

› For impact sockets and accessories with 1” square drive.

Code No. a „

a Q „

Q y 0

6658350 KB2195 1“ 25 1 25 136 1.42

› For impact sockets and accessories with 1” square drive.

› 1.1/2” square drive. › In accordance with DIN 3129.

Code !. Recommended Accessories y 0

6328130 K37 46mm KB 3770, KB 3775 80 2.2606328210 K37 50mm KB 3770, KB 3775 82 2.3866328220 K37 52mm KB 3770, KB 3775 85 2.4206328230 K37 54mm KB 3770, KB 3775 85 2.4506328480 K37 55mm KB 3770, KB 3775 89 2.5006328560 K37 60mm KB 3770, KB 3775 92 2.7316328640 K37 65mm KB 3770, KB 3775 96 2.9016328720 K37 70mm KB 3770, KB 3775 101 3.4666328800 K37 75mm KB 3770, KB 3775 105 3.713 6328990 K37 80mm KB 3770, KB 3775 110 4.2526329020 K37 85mm KB 3770, KB 3775 116 5.3326329100 K37 90mm KB 3770, KB 3775 118 5.6586329290 K37 95mm KB 3770, KB 3775 118 6.3726329370 K37 100mm KB 3770, KB 3775 125 6.5436329450 K37 105mm KB 3770, KB 3775 125 7.5376329530 K37 110mm KB 3770, KB 3775 137 7.9596329610 K37 115mm KB 3770, KB 3775 137 8.833


6329885 KB3790/175 1.1/2 40 175 4.086329888 KB3790/250 1.1/2 40 250 5.206329890 KB3790/330 1.1/2 40 330 6.38

› For impact sockets and accessories with 1.1/2” square drive.

Code No. 0

6676762 KB3770/75 46-90mm 0.026676764 KB3770/75 95-115mm 0.02

Code No. a „

a Q „

Q y 0

6676410 KB3721 1 25 1.1/2 40 95 2.58

KB 3721 REDUCER 1.1/2" TO 1"for impact sockets


63

KB 2190 EXTENSIONS 1"for impact sockets

KB 2195 UNIVERSAL JOINT 1"for impact sockets

KB 3290-175

KB 3290-250

KB 3290-330

SCREWDRIVER

SCREWDRIVERS

2160PH 3C SCREWDRIVERS

67

NUT DRIVER SETS

71

ALLEN KEY SETS

72

SCREWDRIVER SETS

69

2150 3C SCREWDRIVERS

67

TORX® KEYS

74

NUT DRIVERS

71

ALLEN KEYS

72

SCREWDRIVER BITS

75

66

SCREWDRIVER

Seized screws are loosened by gently knocking on the striking cap. Full-length blade transfers the full 100% impact force onto the blade tip.

Soft fast turning zone with hard power point gets the power there quickly. Power point also ensures that the fore�nger reliably guides the blade.

Head marking for speci�cally and rapidly accessing the right screwdriver

338

POWER-GRIP3

Form A

Form B

Form A

Form B

powerful - unerring - absolute precision - wear-resistant... perfect power transmission includedThat is what the new series Power-Grip3 screwdrivers from GEDORE are… the reliable all-rounders for all work in wood, plastic and metal

Useful hanging hole

T Ergonomic grip design for optimum power transfer

T Maximum force involving minimum e�ort T Extensive contact surface with the hand T Ergonomically appropriately placed hard and soft elements give the grip its GEDORE typical kind-to-hands feel

T Suitable for small hands, large hands and for both right and left-handers

Blade injected as a positive �t into the plastic core and matt chrome-plated

The hard core is inside the grip. It takes up the force from the external components and easily transfers it to the shaft. The hard core can be seen at the head marking

Blade fully tempered for a long service life

Blade from GEDORE molybdenum-vanadium-Plus tempered steel for hardness, elasticity and resistance to wear

The torque required by the German Standards Institute (DIN/ISO) is exceeded considerably

The ideal all-rounder for screws in wood, plastic and metal

Precision-made blade tip ensures optimum power transfer onto the screw head

Head marking for speci�cally and rapidly accessing the right screwdriver

Seized screws are loosened by gently knocking on the striking cap. Full-length blade transfers the full 100 % impact force onto the blade tip.

GEDORE has two di�erent blade types for slotted head screws:

Workshop tip = wedge-shaped blade in acc. with DIN ISO 2380-1 Form-A

Electrician tip = slender, parallel blade in acc. with DIN ISO 2380-1 Form-B

Workshop tip for all types of bolting work. Screwdriver tip is wedge-shapedLittle parallel surface of nominal thickness DIN ISO 2380-1 Form-A

Electrician tip specially for screws deep down in the screw shaft e.g. with wire connectors and sockets.Extensive parallel surface of nominal thickness, no wedge-shapeDIN ISO 2380-1 Form-B

T Soft fast turning zone with hard power point - gets the power there quickly

T Power point also ensures that the fore�nger reliably guides the blade

Useful hanging hole.

Ergonomic grip design for optimum power transfer. Maximum force involving minimum e�ort. Extensive contact surface with the hand.Ergonomically placed hard and soft elements give the grip its kind-to-hands feeling.Suitable for all size hands, both right and left-handers.

Precision-made blade tip ensures optimum power transfer onto the screw head.

Made from Gedore Vanadium Molybdenum plus tempered steel for hardness, elasticity and resistance to wear.

Blade fully tempered for a long service life.

The hard core is inside the grip. It takes up the force from the external components and easily transfers it to the shaft. The hard core can be seen at the head marking.

That is what the new series Power-Grip3 screwdrivers from GEDORE are… reliable all-rounders for all work on all materials.

3C SCREWDRIVER

PERFECT POWER TRANSMISSION

67

3C-Screwdrivers

2150 3C SCREWDRIVERSfor slotted head screws, special lengths

› According to DIN ISO 2380-2. › Blade tip according to DIN ISO 2380-1 Form A. › 3-component handles. › Power-Grip3 with hanging hole. › Ergonomic handle design enables precise and fatigue-free working. › Positive-�t joint of handle and blade for optimum transmission of force. › Type of drive marked at end of the handle. › Blade from Gedore Molybdenum-Vanadium-plus tempered steel.

Code No. M ? K L N Ø 0

6679270 2150 3 80 3.0 0.5 165 3.0 0.0396679350 2150 4 100 4.0 0.8 185 4.0 0.0616679430 2150 5.5 100 5.5 1.0 200 5.0 0.0936679510 2150 6.5 150 6.5 1.2 260 6.0 0.1286679780 2150 8 150 8.0 1.2 270 7.0 0.1706679860 2150 10 200 10.0 1.6 320 8.0 0.203

Code No. M ? K L N Ø 0

2822709 2150-2.5-75 75 2.5 0.4 160 2.5 0.0556680280 2150 3-150 150 3.0 0.5 235 3.0 0.0446680360 2150 4-150 150 4.0 0.8 235 4.0 0.0696680520 2150 5.5-150 150 5.5 1.0 250 5.5 0.1046680870 2150 6.5-200 200 6.5 1.2 310 6.0 0.152

2160 PH 3C SCREWDRIVERSfor cross-head screws PH

› According to DIN ISO 8764. › Tip according to DIN ISO 8764-1 PH. › 3-component handles. › Power-Grip3 with hanging hole. › Ergonomic handle design enables precise and fatigue-free working. › Positive-�t joint of handle and blade for optimum transmission of force. › Type of drive marked at end of the handle. › Size 3 blade with hexagon bolster. › Blade from Gedore Molybdenum-Vanadium-plus tempered steel.

Code No. + N ; PH 0

6683110 2160 PH 0 M1,6-M2 145 0 0.0326683380 2160 PH 1 M2-M3 200 1 0.0806683460 2160 PH 2 M3,5-M5 210 2 0.1196683540 2160 PH 3 M5,5-M7 270 3 0.192

2160 PZ 3C SCREWDRIVERSfor cross-head screws Pozi PZ

› Acc. to DIN ISO 8764, tip acc. to DIN ISO 8764-1 PZ. › 3-component handles. › Power-Grip3 with hanging hole. › Ergonomic handle design enables precise and fatigue-free working. › Positive-�t joint of handle and blade for optimum transmission of force. › Type of drive marked at end of the handle. › Size 3 blade with hexagon bolster. › Blade from GEDORE Molybdenum-Vanadium-Plus tempered steel.

Code No. + N < PZ 0

6683970 2160 PZ 0 M1,6-M2 145 0 0.0386684000 2160 PZ 1 M2-M3 180 1 0.0806684190 2160 PZ 2 M3,5-M5 210 2 0.1196684270 2160 PZ 3 M5,5-M7 270 3 0.189

68

SCREWDRIVER

Electrician’sPhillips

POZIDRIV ®

Mechanic’sTORX ®

2153 3C SCREWDRIVERfor slotted head screws, stubby

› Acc. to DIN ISO 2380-2A, blade tip acc. to DIN ISO 2380-1 Form B. › For con�ned spaces. › 3-component handles. › Power-Grip3 with hanging hole. › Ergonomic handle design enables precise and fatigue-free working. › Positive-�t joint of handle and blade for optimum transmission of force. › Type of drive marked at end of the handle. › Blade from GEDORE Molybdenum-Vanadium-Plus tempered steel.

Code No. ? K L N 0

1482432 2153-5.5 5.5 1.0 81 0.036

2161 PH 3C SCREWDRIVERfor cross-head screws PH, stubby

› Acc. to DIN ISO 8764, tip acc. to DIN ISO 8764-1 PH. › For con�ned spaces. › 3-component handles. › Power-Grip3 with hanging hole. › Ergonomic handle design enables precise and fatigue-free working. › Positive-�t joint of handle and blade for optimum transmission of force. › Type of drive marked at end of the handle. › Blade from GEDORE Molybdenum-Vanadium-Plus tempered steel.

Code No. + N 0

1531204 2161 PH 2 M3,5 - M5 81 0.036

2163 TX 3C-SCREWDRIVERSfor recessed TORX® head screws

› 3-component handles. › Power-Grip3 with hanging hole. › Ergonomic handle design enables precise and fatigue-free working. › Positive-�t joint of handle and blade for optimum transmission of force. › Type of drive marked at end of the handle. › Blade from GEDORE Molybdenum-Vanadium-Plus tempered steel. › TORX® = reg. trademark of Acument Intellectual Properties, LLC. USA.

Code No. 7 + & N 0

6685400 2163 TX T6 T6 M2 1,69 145 0.0296685590 2163 TX T7 T7 M2,5 1,99 145 0.0386685670 2163 TX T8 T8 M2,5 2,31 145 0.0386685750 2163 TX T9 T9 M3 2,50 145 0.0386685830 2163 TX T10 T10 M3 - M3,5 2,74 165 0.0396685910 2163 TX T15 T15 M3,5 - M4 3,27 165 0.054

Code No. 7 + & N 0

6686050 2163 TX T20 T20 M4 - M5 3,86 185 0.0606686130 2163 TX T25 T25 M4,5 - M5 4,43 200 0.0826686210 2163 TX T27 T27 M4,5 - M6 4,99 215 0.0986686480 2163 TX T30 T30 M6 - M7 5,52 225 0.1236686560 2163 TX T40 T40 M7 - M8 6,65 240 0.1446686640 2163 TX T45 T45 M8 - M10 7,82 250 0.176

69

3C-Screwdriver Sets

2150-2160 PH-06 MS 3C SCREWDRIVER SET6 pieces

Code No. Contents 0

1482319 2150-2160 PH-06 MS ? 2150 4 5.5 6.5 8 0.660; 2160 PH1 PH2

2163 TX 3C-TORX® SCREWDRIVER SET10 pieces

› Practical set composition in environmentally-friendly cardboard box. › For recessed TORX® head screws. › 3-component handles. › Power-Grip3 with hanging hole. › Ergonomic handle design enables precise and fatigue-free working. › Positive-�t joint of handle and blade for optimum transmission of force. › Type of drive marked at end of the handle. › Blade from GEDORE Molybdenum-Vanadium-Plus tempered steel. › TORX® = reg. trademark of Acument Intellectual Properties, LLC. USA.

Code No. Contents 0

1482335 2163TX 7 2163 T7 T8 T9 T10 T15 T20 T25 T27 T30 T40 0.740

2150-2160 PH-06 ELS 3C SCREWDRIVER SET6 pieces

Code No. Contents 0

1482320 2150-2160 PH-06 ELS ? 2150 6.5 3-150 4-150 6.5-200 0.660; 2160 PH1 PH2

› Practical set composition in environmentally-friendly cardboard box. › For slotted and cross-head screws PH. › 3-component handles. › Power-Grip3 with hanging hole. › Ergonomic handle design enables precise and fatigue-free working. › Positive-�t joint of handle and blade for optimum transmission of force. › Type of drive marked at end of the handle. › Blade from GEDORE Molybdenum-Vanadium-Plus tempered steel.

› Practical set composition in environmentally-friendly cardboard box. › For slotted and cross-head screws PH. › 3-component handles. › Power-Grip3 with hanging hole. › Ergonomic handle design enables precise and fatigue-free working. › Positive-�t joint of handle and blade for optimum transmission of force. › Type of drive marked at end of the handle. › Blade from GEDORE Molybdenum-Vanadium-Plus tempered steel.

70

SCREWDRIVER

Code No. 0

6698650 4611 115

Electronic Screwdrivers

165-171-06 ELECTRONIC SCREWDRIVER SET6 pieces

› For slotted head and cross-slotted head screws PH. › Blade in high-alloy Chrome Vanadium Molybdenum steel, chrome-plated. › Tip additionally coated for highest precision and corrosion protection. › 2-component handle in ergonomic design. › Pivoting end cap with micro anti-slip surface. › Colour coding of the drive type. › In plastic case. › With Gedore Check-Tool-System: 2-colour foam insert to check that the set is complete

165 TX-06 ELECTRONIC SCREWDRIVER SET6 pieces

› For recessed TORX® head screws. › Blade in high-alloy Chrome Vanadium Molybdenum steel, chrome-plated. › Tip additionally coated for highest precision and corrosion protection. › 2-component handle in ergonomic design. › Pivoting end cap with micro anti-slip surface. › Colour coding of the drive type. › In plastic case. › With GEDORE Check-Tool-System: 2-colour foam insert to check that the set is complete.

Code No. Contents 0

1902849 165-171-06 ; 165 PH 000 00 0 0.385? 171 IS 1,2 1,8 2,5

Code No. Contents 0

1902857 165-TX-06 7 165 TX T5 T6 T7 T8 T9 T10 0.415

4611 POWER TESTING SCREWDRIVER › For 6-24 Volt with clamp cable.

Code No. $ Ø ! N 0

1746731 2133 5,5mm - 5 5.5 225 0.1071746758 2133 6mm - 5 6.0 225 0.1091746766 2133 7mm - 6 7.0 235 0.1351746855 2133 8mm - 6 8.0 235 0.1521746863 2133 9mm - 6 9.0 235 0.1681746898 2133 10mm 10 6 10.0 245 0.1981746901 2133 11mm 13 8 11.0 245 0.2021746928 2133 12mm 13 8 12.0 245 0.2211746944 2133 13mm 13 8 13.0 245 0.225

71

Nut Drivers

2133 NUT DRIVERS WITH 3C HANDLE › Acc. to DIN 3125, ISO 2725-1. › 3-component handles. › Power-Grip3 with hanging hole. › Ergonomic handle design enables precise and fatigue-free working. › Positive-�t joint of handle and blade for optimum transmission of force. › Head depth 25 mm, blade length 125mm. › 10 mm and larger with hexagon bolster. › Blade from GEDORE Molybdenum-Vanadium-Plus steel.

2133 NUT DRIVER SETSfor hexagon nuts

› Made up of most popular sizes.

Code No. Contents 0

1746947 2133-06S 2133 5,5 6,0 7,0 8,0 9,0 10,0 0.6481746946 2133-06L 2133 8,0 9,0 10,0 11,0 12,0 13,0 0.9371746948 2133-09 2133 5,5 6,0 7,0 8,0 9,0 10,0 11,00 12,00 13,00 1.300

55 SPARK PLUG SPANNER 102 VDE NUT DRIVERS 148

72

SCREWDRIVER

Code No. y 0

6342200 42 0,7mm 32 16342390 42 0,9mm 34 16342470 42 1,3mm 40 16340260 42 1,5mm 45 26340340 42 2mm 50 26340420 42 2,5mm 56 36340500 42 3mm 63 46340690 42 4mm 70 106340770 42 5mm 80 186340850 42 6mm 90 306340930 42 7mm 95 426341070 42 8mm 100 606341150 42 9mm 106 806341230 42 10mm 112 1006341231 42 11mm 117 1306341310 42 12mm 125 1606341580 42 14mm 140 2606341581 42 16mm 150 3206341660 42 17mm 160 4406341740 42 19mm 180 6206341820 42 22mm 200 950

Code No. y 0

6341900 42 24mm 224 12506342550 42 27mm 244 17606342040 42 1/16 AF 45 16342041 42 5/64 AF 50 26344330 42 3/32 AF 53 36344410 42 1/8 AF 59 56344411 42 9/64 AF 62 76344680 42 5/32 AF 65 96344760 42 3/16 AF 72 156344840 42 7/32 AF 78 206344920 42 1/4 AF 84 306345060 42 5/16 AF 97 556345140 42 3/8 AF 110 906345141 42 7/16 AF 114 1406345220 42 1/2 AF 122 1906345300 42 9/16 AF 136 2706345490 42 5/8 AF 146 3606345491 42 11/16 AF 156 4206345570 42 3/4 AF 175 6006345571 42 7/8 AF 195 9006345572 42 1 AF 218 1400

Code ! Contents 0

6347510 42-7M 2 2,5 3 4 5 6 8 0.2006349050 42-8M 3 4 5 6 8 10 12 14 0.700 6349051 42-88M 2 2,5 3 4 5 6 8 10 0.3006349052 42-100M 2 2,5 3 4 5 6 7 8 9 10 0.400012112 42-22M 0,7 0,9 1,3 1,5 2 2,5 3 4 5 6 7 8 9 10 11 12 14 16 17 19 22 24 6.2006349053 42-88P 3/32” 1/8” 5/32” 3/16” 7/32” 1/4” 5/16” 3/8” 0.2006348910 42-9P 1/16” 5/64” 3/32” 1/8” 5/32” 3/16” 1/4” 5/16” 3/8” 0.3006351974 42L-7M 2 2,5 3 4 5 6 8 0.2006351975 42L-9M 1,5 2 2,5 3 4 5 6 8 10 0.4006351976 42L-14M* 1,5 2 2,5 3 4 5 6 7 8 9 10 11 12 14 2.200

42-88M

42L-9M

42 (MM) / (AF) HEXAGON ALLEN KEYSfor hexagon screws

› For hexagon socket head bolts. › Chrome Vanadium steel 59CrV4. › Gunmetal �nish. › Short series. › In accordance with SANS 1210 and DIN 911.

Allen Keys

42 / 42L (MM) / (AF) HEXAGON ALLEN KEY SETS

› Made up of most popular sizes.

73

Code No. y 0

6350809 42L-1,5 90 26350810 42L-2 100 36351030 42L-2,5 112 56351110 42L-3 125 86351380 42L-4 142 206351460 42L-5 163 306351540 42L-6 184 502977486 42L-7 194 706351620 42L-8 205 1006351621 42L-9 216 1406351700 42L-10 231 1806351890 42L-11 244 2406351891 42L-12 259 2906351970 42L-14 290 4456351971 42L-17 333 600

1543375 42L-1/16 80 21543376 42L-5/64 80 31543377 42L-3/32 84 41543318 42L-1/8 94 71543319 42L-9/64 102 101543326 42L-5/32 103,5 131543334 42L-3/16 111 301543342 42L-7/32 122,5 401543369 42L-1/4 130 451543350 42L-5/16 150 821543385 42L-3/8 168 1301543386 42L-7/16 188 2001543393 42L-1/2 206 2901543407 42L-9/16 266 400

Code No. y 0

2647257 42T-2 140 352647265 42T-2,5 152 402647273 42T-3 165 452647281 42T-4 182 552647303 42T-5 200 702647311 42T-6 220 902681439 42T-7 230 1302647386 42T-8 240 1502647338 42T-10 264 230

2647351 42T-5/64 140 352647352 42T-3/32 152 402647354 42T-1/8 166 502647361 42T-9/64 182 502647362 42T-5/32 182 502647370 42T-3/16 200 602647388 42T-7/32 220 802647389 42T-1/4 220 952647397 42T-5/16 240 1502647400 42T-3/8 264 220

Code ! Contents 0

6351977 42KL-7M 1,5 2 2,5 3 4 5 6 0.2506351978 42KL-9M 1,5 2 2,5 3 4 5 6 8 10 0.395 6351979 42KL-8P 3/64” 1/16” 5/64” 3/32” 7/64” 1/8” 9/64” 5/32” 0.300

Code ! Contents 0

6351972 42SCL-6M 3 4 5 6 8 10 0.1706351973 42SCL-7M 2 2,5 3 4 5 6 8 0.175

42SCL HEXAGON ALLEN KEY SETS

› Chrome Vanadium steel 59CrV4. › Blackened �nish and blue

polypropylene holder. › Easy to handle. › Indispensable pocket set for

electricians.

42L (MM) / (AF) HEXAGON ALLEN KEYSfor in-hex screws

› For hexagon socket head bolts. › Chrome Vanadium steel 59CrV4. › Gunmetal �nish. › Long pattern for use in hard to access areas. › Cranked shaft, resulting in a lever e�ect during tightening or loosening operation.

42KL (MM) / (AF) HEXAGON ALLEN KEY SETSfor in-hex screws

› Hexagon socket key with ball end and holder. › Chrome Vanadium steel 59CrV4. › Gunmetal �nish.

42T (MM) / (AF) HEXAGON ALLEN KEYSfor in-hex screws

› Chrome Vanadium steel 59CrV4. › Blackened �nish and blue polypropylene handle. › T-shaped handle, making tightening or loosening operations easier for users.


43 KTX CRANKED SOCKET KEY SETfor recessed TORX® screws, with ball end

Code ! Contents 0

6367897 43KTX-8M T9 T10 T15 T20 T25 T27 T30 T40 0.130

74

SCREWDRIVER

Code No. + & y 0

6363550 43 TX-T6 M2 1,67 42 46363630 43 TX-T7 M2,5 1,99 48 56363710 43 TX-T8 M2,5 2,31 48 56363980 43 TX-T9 M3 2,50 48 56364010 43 TX-T10 M3-M3,5 2,74 51 86364280 43 TX-T15 M3,5-M4 3,27 54 86364360 43 TX-T20 M4-M5 3,86 57 116364440 43 TX-T25 M4,5-M5 4,43 60 146364520 43 TX-T27 M4,5-M5-M6 4,99 64 226364600 43 TX-T30 M6-M7 5,52 70 296364790 43 TX-T40 M7-M8 6,65 76 416364870 43 TX-T45 M8-M10 7,82 83 616364950 43 TX-T50 M10 8,83 95 876365090 43 TX-T55 M12 11,22 108 1766365170 43 TX-T60 M14 13,25 120 180


*PACKAGING SUBJECT TO CHANGE WITHOUT NOTICE.

42SCKL HEXAGON ALLEN KEY SETfor in-hex screws

› Hexagon socket key with ball end and holder. › Chrome Vanadium steel 59CrV4. › Gunmetal �nish.

Code ! Contents 0

6351980 42SCKL 5M 5 6 7 8 10 0.270

43TX CRANKED SOCKET KEYSfor recessed TORX® screws

› Made from Chrome Vanadium steel 59CrV4. › L-shaped. › Long pattern for use in hard to access areas. › Gunmetal �nish.

43TX CRANKED SOCKET KEY SETSfor recessed TORX® screws

› Hexagon socket key with ball end and holder. › Chrome Vanadium steel 59CrV4. › Gunmetal �nish. › Supplied in plastic wallet.

Code ! Contents 0

6360959 43TX-09 Plastic Holder T9 T10 T15 T20 T25 T27 T30 T40 0.0906360961 43TX-15* Plastic Holder T6 T7 T8 T9 T10 T15 T20 T25 T27

T30 T40 T45 T50 T55 T600.500

› Made from Chrome Vanadium steel 59CrV4. › L-shaped. › Cranked shaft, resulting in a lever e�ect during tightening or loosening operation. › Blackened �nish.


TORX® Keys

163 TX TORX® SCREWDRIVER SETS 69

75

Code No. y 0

654124 690 PH 1 25 5654132 690 PH 2 25 5655279 690 PZD - 1 25 5655287 690 PZD - 2 25 5

Code No. + & y 0

654183 687 TX - T6 M2 1,67 25 0.005654191 687 TX - T7 M2,5 1,99 25 0.005654205 687 TX - T8 M2,5 2,31 25 0.005654213 687 TX - T9 M3 2,50 25 0.005654221 687 TX - T10 M3-M3,5 2,74 25 0.005654248 687 TX - T15 M3,5-M4 3,27 25 0.005654256 687 TX - T20 M4-M5 3,86 25 0.005654264 687 TX - T25 M4,5-M5 4,43 25 0.005654272 687 TX - T27 M4,5-M5-M6 4,99 25 0.005654280 687 TX - T30 M6-M7 5,52 25 0.005654299 687 TX - T40 M7-M8 6,65 25 0.005

POZIDRIV® = Registered Trademark of GKN Fasteners.




Code No. + & y 0

6367106 43 TXL-T6 M2 1,67 90 0.0076367107 43 TXL-T7 M2,5 1,99 100 0.0076367108 43 TXL-T8 M2,5 2,31 110 0.0076367109 43 TXL-T9 M3 2,50 124 0.0086367110 43 TXL-T10 M3-M3,5 2,74 138 0.0106367380 43 TXL-T15 M3,5-M4 3,27 158 0.0206367460 43 TXL-T20 M4-M5 3,86 178 0.0206367540 43 TXL-T25 M4,5-M5 4,43 190 0.0306367620 43 TXL-T27 M4,5-M5-M6 4,99 200 0.0506367700 43 TXL-T30 M6-M7 5,52 210 0.0606367890 43 TXL-T40 M7-M8 6,65 215 0.0856367891 43 TXL-T45 M8-M10 7,82 224 0.1106367892 43 TXL-T50 M10 8,83 232 0.1856367893 43 TXL-T55 M12 11,22 248 0.2006367894 43 TXL-T60 M14 13,25 278 0.415

687 / 690 SCREWDRIVER BITS › 687 For TORX® screws. › 690 For Phillips and POZIDRIV® screws. › Manufactured from high quality Molybdenum tool steel. › Gun metal �nish.

TORX®

POZIDRIV®

43TXL CRANKED SOCKET KEYSfor recessed TORX® screws

› Made from Gedore Chrome Vanadium steel 59CrV4 › L-shaped. › Long pattern for use in hard to access areas. › Gun-metal �nish.

43TV TORX® GAUGE TESTER

› Easy determination of internal or external TORX® sizes

43TXL CRANKED SOCKET KEY SETSfor recessed TORX® screws

› L-shaped. › Long pattern for use in hard to access areas.

Code ! Contents 0

6367895 43TXL 09 T7 T8 T9 T10 T15 T20 T25 T30 T40 0.3006367896 43TXL 15

T6 T7 T8 T9 T10 T15 T20 T25 T27 T30 T40 T45 T50 T55 T60

1.200

Code No. 0

024700 43 TV 23


Screwdriver Bits

PLIERS

76

PLIERS

SETS

LOCKGRIP / UNIVERSAL

95

CIRCLIP

88

FLAT / ROUND NOSE

81

CABLE STRIPPERS / CRIMPERS

86

PIPE WRENCHES

92

MECHANICS / FENCING

83

CUTTERS

96

TIN SNIPS / PIPE CUTTERS

97

COMBINATION PLIERS

79

78

PLIERS

TL pliers are painted black by a robot, using water soluble paint.

Blank cropped to size from C50 steel. The blanks are ‘normalised’ to obtain an even finer grain and a more uniform structure with optimum strength. After descaling, the blanks are coined for subsequent

operations.

Hot forged in a drop forging die. The excess burr is removed using an eccentric press.

1. 2. 3.

The head is machined in a CNC-controlled machining centre. The rivet hole is drilled and counter-bored.

The joint clearance and the outer contour are milled. The geometry of the joint area and the gripping

geometry are broached.

The moving and fixed pliers legs are riveted together. A smooth-moving joint with no play is an essential

requirement for a safe one-handed operation.

The joint faces are precision milled. The pliers head takes on its final form.

4. 5. 6.

In a chamber hardening kiln, the pliers are hardened in a protective gas atmosphere, quenched in oil and finally annealed. The design of the hardening kiln ensures that the process gases are uniformly distributed, which has a

positive effect on the material properties.

The pliers head is ground to achieve a flush geometry.The cutting edges of GEDORE pliers are once again induction hardened. The additional hardness that this

achieves ensures a good cutting performance and extended durability of the tool.

7. 8. 9.

8250 Combination Pliers Manufacturing Process

The surface is cleaned by sand blasting. The removal of scale and grease is necessary in

preparation for the electroplating process.

The pliers are laser marked and the joint is oiled.

Tip: an occasional drop of oil on the joint will ensure that your pliers retain ease of movement.

VDE pliers are subjected to an individual test in accordance with DIN EN 60900 / IEC 60900:2004.

GEDORE Austria has been a certified manufacturing plant for VDE protective insulated plierssince 2003.

Nickel plated and matt-chrome plated. The electrolytically deposited nickel coating provides the corrosion protection. The electroplated chrome improves

the look and gives the pliers a perfect finish.

10. 11. 12.

The two-component handles are pressed on and bonded.

13.

79

Code No. y

6707070 8250 - 180 JC 180 2406707310 8250 - 200 JC 200 320

R

JC TL

R

8250 POWER COMBINATION PLIERS › According to DIN ISO 5746. › For heavy continuous use. › Good lever action for easy cutting. › For �at and round material.

› To cut all wire types including piano wire, 1.6 mm. › Gedore special hardened and tempered steel, drop-forged, oil-hardened and annealed. › JC = chrome plated, with 2-component handles. › TL = steel-grey, with blue dipped non-slip handles.

Maximum cutting performance yet

with a low level of e�ort expended

thanks to an optimum interaction

of cutting geometry, eccentric rivet

bearing and ergonomic handle

design.

› Identi�es the GEDORE Power Pliers range, o�ering increased cutting and gripping force with up to 35% less e�ort.

High-grade 2-component handles

with �nger protection enable work

to be done ergonomically and to the

exclusion of tiredness.

Roughly toothed gripping surfaces for

securely holding screws, pipes etc.

Gripping surface with �le-cut

for a particularly e�ective

hold

Inductively hardened cutting edges

(62 - 64 HRC) ensure constant cutting

power over a long time span.

8250 POWER COMBINATION PLIERS

8250-225 TL POWER COMBINATION PLIERS

› For heavy, continuous use. › Good lever action for easy cutting. › Induction hardened precision cutting edge. › Hardness approximately 63HRC. › To cut all wire types, inclusing piano wire. › DIN ISO 5756.

Combination Pliers

Code No. y

6708040 8250 - 225 TL 225 400

R

8260 FENCING PLIERS

› For heavy duty, continuous use. › CrV material. › Hardened and tempered. › Cutting edges induction hardened.

Code No. y

670250 8260 - 250 250 570670300 8260 - 300 310 930

80

PLIERS

P

VDE 8316 H POWER SIDE CUTTER 150 S 8303 JC PLIERS SET 85

JC TL

8316 POWER SIDE CUTTER

› According to DIN ISO 5749. › Good lever action for easy cutting. › For hard wire/piano wire. › Maximum cutting capacity Ø 1.4 - 2.0mm.

› Gedore special hardened and tempered steel, drop-forged, oil-hardened and annealed. › JC = chrome plated, with 2-component handles. › TL = steel-grey, with blue dipped non-slip handles.

Maximum cutting performance with

a low level of e�ort expended due to

an optimum interaction of cutting

geometry, eccentric rivet bearing and

ergonomic handle design.

Inductively hardened cutting

edges (63 - 65 HRC) ensure

constant cutting power over a

long time span.

8316 POWER SIDE CUTTERSAmerican pattern

Code No. Ø y

6711930 8316 - 140TL 1,4 140 1326744190 8316 - 140 JC 1,4 140 1526744510 8316 - 160 JC 1,6 160 2106745080 8316 - 200 JC 2,0 200 305

Side Cutters / Pincers

81

P Q 8380 TOWER PINCERS › Heavy-duty wire braid and mesh-cutting pincers. › Accoding to DIN ISO 9242, Form A. › Induction hardened precision cutting edges, hardness 61-63 HRC. › For medium-hard wire, 1.6 mm. › Heads ground, steel-grey, with blue dipped non-slip handles (TL). › Geometrically optimised head and handle areas for ergonomic use. › In high quality tool steel.

8381 PINCERS › Standard heavy-duty pincers. › Accodingto DIN ISO 9243, Form A. › Induction hardened precision cutting edges, hardness 61-63 HRC. › Heads ground, steel-grey, with blue dipped non-slip handles (TL). › In high quality tool steel.

Code No. y

6752370 8381 - 160 TL 160 2256751990 8381 - 200 TL 200 4106752450 8381 - 225 TL 224 450

Code No. y

6752020 8380 - 225 TL 225 3156752100 8380 - 250 TL 250 400

Flat Nose / Round Nose Pliers

S

JC

8112 ROUND NOSE PLIERSserrated

› Similar to DIN ISO 5745. › Short jaws, serrated gripping faces. › For gripping and bending. › Gedore special hardened and tempered steel, drop-forged, oil-hardened and annealed. › JC = chrome-plated, with 2-component handles. › TL = steel-grey, with blue dipped non-slip handles.

R

JC

8120 FLAT NOSE PLIERSwithout cutting edge, serrated gripping faces

› Accoding to DIN ISO 5745. › Long jaws, serrated gripping faces. › For holding and bending. › Gedore special hardened and tempered steel, drop-forged, oil-hardened and annealed. › JC = chrome plated, with 2-component handles. › TL = steel-grey, with blue dipped non-slip handles.

TL

Code No. y

6710370 8120 - 160 TL 160 1216715170 8120 - 160JC 160 140

TL

Code No. y

6713200 8112 - 140 TL 140 926713390 8112 - 140 JC 140 117

82

PLIERS

› Accoding to DIN ISO 5745. › Long, �at-round jaws, straight gripping faces, serrated. › For holding, gripping, bending and cutting. › Induction hardened precision cutting edges, hardness 61-63 HRC. › Gedore special hardened and tempered steel, drop-forged, oil-hardened and annealed. › JC = chrome plated, with 2-component handles. › TL = steel-grey, with blue dipped non-slip handles.

T

TL

8132 AB BENT NOSE TELEPHONE PLIERSwith cutting edge, serrated, angled pattern

› Similar to DIN ISO 5745. › Long, �at-round jaws, angled gripping surfaces, serrated. › 45 ° angled tips make gripping round the corner possible. › Induction hardened precision cutting edges, hardness 61-63 HRC. › Gedore special hardened and tempered steel, drop-forged, oil-hardened and annealed. › JC = chrome plated, with 2-component handles. › TL = steel-grey, with blue dipped non-slip handles.

T

JC

TL

8132 TELEPHONE PLIERSwith cutting edge, serrated, straight pattern

8135 TELEPHONE PLIERSwithout cutting edge, serrated, straight pattern

› Accoding to DIN ISO 5745, straight pattern. › Flat-round tapered jaws, cross-hatched gripping surfaces and �ne-tipped nose. › Also suitable as needle nose soldering pliers. › Gedore special hardened and tempered steel, drop-forged, oil-hardened and annealed. › Steel-grey, with blue dipped non-slip handles.

Code No. y

6710610 8132 - 140 TL 140 1036718860 8132 - 140 JC 140 1186719240 8132 - 160 JC 160 1406719670 8132 - 200 JC 200 200

JC

Code No. y

6711180 8132 - AB - 160 TL 160 1206720920 8132 - AB - 160 JC 160 1406711260 8132 - AB - 200 TL 200 1756721300 8132 - AB - 200 JC 200 200

T

Code No. y

6722460 8135 - 140 TL 140 956722620 8135 - 160 TL 160 128

83

T 8136 MECHANIC‘S PLIERSwithout wire cutter, straight pattern

› According to DIN ISO 5745. › Flat-round tapered jaws, cross-hatched

gripping surfaces. › For holding, gripping and bending. › Fine-tipped nose, for safe work in con�ned

spaces. › Gedore special hardened and tempered steel,

drop-forged, oil-hardened and annealed.

› JC = chrome-plated, with 2-component handles. › TL = steel-grey, with blue dipped non-slip

handles.

JC

TL

8133 MULTIPLE PLIERSwith cutting edge, serrated, straight pattern

8133 MULTIPLE PLIERS › Multifunctional pliers for the mechanical and electronic �elds. › For holding, cutting, insulation-stripping, crimping, squeezing. › Flat-round jaws, straight gripping faces, serrated. › For medium-hard wire, 1.6 mm. › Gedore special hardened and tempered steel, drop-forged, oil-hardened and annealed.

› JC = chrome plated, with 2-component handles. › TL = steel-grey, with blue dipped non-slip handles.

Gripping faces with �le-cut for safe holding.

Cutting edge induction hardened (62-64 HRC).

Crimping of conductor end-sleeves 0.5-2.5mm2.

Squeezing of insulated �at plugs 1.0-2.5mm2.

Stripping of wire sizes 0.5/1.5/2.5mm2.

T

Code No. y

6722110 8133 - 180 JC 160 120

Mechanic‚s Pliers

Code No. y

6722890 8136 - 200 TL 200 178

84

PLIERS

Pliers sets › Produced in-house by GedoreAustria. › Combination, �at-nosed, round-nosed and mechanic‘s pliers made from Gedore special hardened

and tempered steel. › Side cutters and end cutting nippers made from GEDORE high-performance hardened and tempered steel. › Chrome-plated, 2-component handle protectors. › Hot-forged tempered steel. › Precision-machined, oil-hardened and annealed.

› Induction-rehardened cutting edges. › Protective nickel and chrome plating. › Optimum transfer of force. › High cutting performance. › Fatigue-free, even in constant use. › Guaranteed GEDORE quality.

S 8003 JC PLIERS SET3 pieces

› Practical set in environmentally friendly cardboard box.

Code No. Contents

6701110 S 8003 JC8132-200 JC Telephone Pliers8250-200 JC Combination Pliers8316-200 JC Side Cutters

1025

1102-003 PLIERS SET3 pieces

› In Gedore L-BOXX® Mini, including divider set.

Code No. Contents

1692305 1102-0038132-160 JC Telephone Pliers8250-180 JC Combination Pliers8316-160 JC Side Cutters

940

NEW

85

Cable cutters

BOLT CUTTERS

› Notch cut; the cutters press into the material and create a notch. The material is compacted and thus separated. › The wire rope is compressed and thus loses its circular cross-

section at the cut. The wire rope fans out as a result.

GEDORE WIRE ROPE CUTTERS

› The cutting plates slide past each other dissecting the material. › The wire rope is cleanly cut and retains its circular cross-

section. It does not fan out.

Splicing: › The old seafaring ability to separate the rope into its individual strands so as

to then braid them into a loop or lengthen the rope with another rope without knotting.

8320 JL WIRE ROPE CUTTERS

Execution: › Easy-to-change cutting plates. › Cutting plates of powder metallurgical high-speed steel (HSS). Manufactured in the MIM process

(Metal Injection Moulding). › Extremely high durability compared to traditional wire rope cutters. › Extremely soft shearing cut reliably prevents the wire rope from fanning out. › Tip: Can be operated with one hand of an average size up to a 5mmØ. Therefore optimally suited as

shears in an emergency at sea.Jaws/cutting edges: › Specially arched cutting edges. › Easy to replace cutting plates if worn. › Hardness 62-65 HRC. › Low force needed due to the optimum cutting-edge geometry. › Two integrated press pro�les for Bowden cable terminal sleeves and cable end sleeves.

Cutting performance: › Wire ropes up to 1800N/mm2 with maximum 6mmØ. (e.g. stainless steel wire ropes, wire ropes with

steel and textile cores, Bowden cables, shears). › Wire up to 750N/mm2 with maximum 4mmØ. (e.g. nails/wire nails, screws, bolts, ceiling banners). › Single- and multi-core copper and aluminium cables with maximum 6mmØ.

Joint: › Adjustable joint for precise cutting plate guidance. › Latch to prevent unwanted opening.

Handles: › With 2-component handles.

Material/�nish: › Plier body hot drop-forged. › Chrome plated.

Fanning out: › Separation into individual strands is not wanted when cutting wire ropes. It is a very laborious

business to splice wire ropes. That is why more up-to-date ways are available to incorporate loops in wire ropes. However, they require a smooth cut without any spliced strands.

Code No. y

2788799 8320 - 200 JL 200 480

S8303 JC PLIERS SET3 pieces

› Practical set in environmentally friendly cardboard box.

Code No. Contents

6703160 S 8303 JC142 10 JC Universal Pliers8250-180 JC Combination Pliers8316-160 JC Side Cutters

1005

NEW

86

PLIERS

8148 PRECISION STRIPPING TOOLfor data cables

› User-friendly, easy to handle, all-round cut. › Precision adjustment of cutting depth (adjuster wheel with 9 positions). › Replaceable blade. › Safe, rounded, pocket design. › Stripping capacity: 2.5 - 11mm. › Insulation thickness: up to 1.0mm.

8147 HEAVY-DUTY CABLE STRIPPING TOOL › Professional wire stripping tool with 2 cable hooks. › Compact and user-friendly, even in the most di�cult conditions. › For cables (up to 40mmØ) with any kind of insulation. › Blade can be locked in one of three positions (circular, straight or spiral cuts). › Cable capacity: 4.5 - 40mmØ. › Insulation thickness: up to 4.5mm.

Dimensions: › with small cable hook: 150 x 42 x 30.5mm. › with large cable hook: 167 x 52 x 30.5mm. › E-8147 = Spare blade.

Code No. Ø

1830856 8147 4,5-40 1961884719 E-8147 Spare Blade 2

Code No. Ø

1830864 8148 2,5-11 431884727 E-8148 Spare Blade 2

Dimensions: › 90.5 x 39.5 x 19mm. › E-8148 = Spare blade.

Stripping Tools

8146-1 8146-2

8146 STRIPPING PLIERSwith exchangeable module inserts, self-adjusting

› Self-adjusting cutting and stripping tool for modern electrical installations and equipment circuitry (90% of all wires can be stripped without any adjustment of the tool). › The use of easily exchangeable module inserts allows accurate stripping

of a wide range of insulation materials, including PVC and PTFE, with just one tool. › Flat blade included in delivery. › Dimensions: 191 x 123 x 20mm.

Stripping capacity: › 8146-1 with �at blade: 0.02-10mm2 / AWG 34-8 (for PVC insulation). › 8146-2 with round blade: 4-16mm2 / AWG 10-5.

Cutting values: › Flexible wires up to 10mm2 / AWG 8. › Rigid wires up to 1.5mm2 / AWG 16.

Code No. Description mm2 AWG 1830805 8146 Stripping pliers including module insert 8146-1 0,02-10 34-8 1801830813 8146-1 Module insert with �at blade 0,02-10 34-8 151830821 8146-2 Module insert with round blade 4-16 12-6 16

8146

87

ADVANTAGES: › Reliable: parallel action ensures precision crimping. › Easy to handle: components kept in view throughout the crimping process, easily accessible release function allows

quick change of insert modules without the use of additional tools. › Comfortable: lightweight, plastic-sheathed tool frame for comfort grip - even at low temperatures. › Practical: insert modules, easy to change and clearly labelled, supplied in pairs on an pin in a storage box to prevent

loss (storage boxes interconnect - like a jigsaw puzzle). › Versatile and economical: just one tool base frame can be used with all the various insert modules to carry out a

wide range of crimping processes, including heavy plug and socket connectors, coaxial connectors, optic �bres and RJ45 plugs.

CHANGING OF THE CRIMPING INSERTS › By pressing the release of the crimping insert you can easily remove the insert. › Remove the crimping insert and put in the required insert

while pressing down the release.

Crimp Wrench modular

S 8140 A

8140-05 8140-09 8140-11

S 8140 D

8140-14 8140-16 8140-17

Crimp Wrench Sets

S 8140 A CRIMPING PLIERS SET AUTOMOTIVE4 pieces

› Practical set made up for speci�c requirements in automotive engineering. › Ideal for high-standard crimping. › Can be individually upgraded by purchasing

additional module inserts. › Module inserts changeable without tools. › In practical blister packaging.

S 8140 D CRIMPING PLIERS SET DATA COM4 pieces

› Practical set made up for speci�c requirements in data-communications installations. › Ideal for high-standard crimping. › Can be individually upgraded by purchasing additional

module inserts. › Module inserts changeable without tools. › In practical blister packaging.

Code No. Contents

1830190 S 8140 A Cripmer 8140 Inserts 05 09 11 754

Code No. Contents

1830937 S 8140 D Cripmer 8140 Inserts 14 16 17 711

88

PLIERS

S 8140 E

8140-01 8140-02 8140-05

S 8140 J

8140-02 8140-06 8140-18

S 8140 E CRIMPING PLIERS SET ELECTRONIC4 pieces

› Practical set made up for speci�c requirements for electricians. › Ideal for high-standard crimping. › Can be individually upgraded by purchasing additional


S 8140 J CRIMPING PLIERS SET INDUSTRIAL4 pieces

› Practical set made up for speci�c requirements in industrial maintenance. › Ideal for high-standard crimping. › Can be individually upgraded by purchasing additional


Code No. Contents

1830899 S 8140 E Cripmer 8140 Inserts 01 02 05 760

Code No. Contents

1830929 S 8140 J Cripmer 8140 Inserts 02 06 18 752

Circlip pliers for external retaining rings (shafts)

B M 8000 A 0 - A 4 - STRAIGHT

CIRCLIP PLIERS FOR EXTERNAL RETAINING RINGSForm A

› For retaining rings as per DIN 471, DIN 983. › DIN 5254 Form A. › Straight tips. › With opening spring . › With clamping protection.

› Forged Gedore Chrome Vanadium special hardened and tempered steel. › Precision machined, oil hardened and

annealed. › Black, with red dipped handles.

B N 8000 A 01 - A 41 - BENT

CIRCLIP PLIERS FOR EXTERNAL RETAINING RINGSForm B

› For retaining rings as per DIN 471, DIN 983. › DIN 5254 Form B. › 90° angled tips. › With opening spring. › With clamping protection.

› Forged Gedore Chrome Vanadium special hardened and tempered steel. › Precision machined, oil hardened and

annealed. › Black, with red dipped handles.

Code No. F E

6701380 8000 A 0 5/32-3/8 3-10 966701460 8000 A 1 3/8-1 10-25 986701540 8000 A 2 3/4-2.3/8 19-60 1866701620 8000 A 3 1.5/8-4 40-100 3106701700 8000 A 4 3.3/8-5.1/2 85-140 555

Code No. F E

6702270 8000 A 01 5/32-3/8 3-10 976702350 8000 A 11 3/8-1 10-25 976702430 8000 A 21 3/4-2.3/8 19-60 1826702510 8000 A 31 1.5/8-4 40-100 3176702780 8000 A 41 3.3/8-5.1/2 85-140 563

89

B M

B N 8000 A 5 - STRAIGHT

CIRCLIP PLIERS FOR EXTERNAL RETAINING RINGS

› Straight tips. › Black, tips and lock lever zinc plated. › The toothed bracket stops the pliers legs from

straddling beyond the permitted working area. › This ensures safe working even in hidden

�tting positions. › Locking pin can be replaced.

› Non-crush type release lever with handle recesses, red dip insulated. › Precision machined, oil hardened and

annealed. › E-8000 A = pair of spare tips.

8000 A 51 - BENT CIRCLIP PLIERS FOR EXTERNAL RETAINING RINGS

› 90° angled tips. › Tips and lock lever zinc plated. › Lever handle end red dip insulated. › Finger protection.

› Reinforced safety arms. › Precision machined, oil hardened and

annealed. › E-8000 A = pair of spare tips.

A M

A N

Circlip pliers for internal retaining rings (bores)

8000 J 0 - J 4 - STRAIGHT CIRCLIP PLIERS FOR INTERNAL RETAINING RINGSForm C

› For retaining rings as per DIN 472, DIN 984. › DIN 5256 Form C. › Straight tips. › Forged Gedore Chrome Vanadium special

hardened and tempered steel.

› Precision machined, oil hardened and annealed. › Black, with blue dipped handles.

8000 J 01 - J 41 - BENT CIRCLIP PLIERS FOR INTERNAL RETAINING RINGSForm D

› For retaining rings as per DIN 472, DIN 984 › DIN 5256 Form D. › 90° angled tips. › Forged Gedore Chrome Vanadium special

hardened and tempered steel.

› Precision machined, oil hardened and annealed. › Black, with blue dipped handles.

Code No. D C

6703240 8000 J 0 3/8-9/16 8-13 806703320 8000 J 1 3/8-1 12-25 816703400 8000 J 2 3/4-2.3/8 19-60 1646703590 8000 J 3 1.5/8-4 40-100 2816703670 8000 J 4 3.3/8-5.1/2 85-140 472

Code No. D C

6704130 8000 J 01 3/8-9/16 8-13 806704210 8000 J 11 3/8-1 12-25 826704480 8000 J 21 3/4-2.3/8 19-60 1616704560 8000 J 31 1.5/8-4 40-100 2796704640 8000 J 41 3.3/8-5.1/2 85-140 484

Code No. F E y

6701890 8000 A 5 4.13/16-11.7/8 122-300 550 1900

Code No. 5701840 E-8000 A 5 Spare Tips 72

Code No. F E y

6702860 8000 A 51 4.13/16-11.7/8 122-300 560 1898

Code No. 5702810 E-8000 A 51 Spare Tips 112

90

PLIERS

A M

A N 8000 J 5 - STRAIGHT

CIRCLIP PLIERS FOR INTERNAL RETAINING RINGS

8000 J 51 - BENT CIRCLIP PLIERS FOR INTERNAL RETAINING RINGS

› 90° angled tips. › Black, tips and lock lever zinc plated. › Lever handle end blue dip insulated. › Finger protection.

› Reinforced safety arms. › Precision machined, oil hardened and

annealed. › E-8000 J = pair of spare tips.

Code No. D C y

6703750 8000 J 5 4.13/16-11.7/8 122-300 565 1836

Code No. 5703700 E-8000 J 5 Spare Tips 72

Code No. D C y

6704720 8000 A 51 4.13/16-11.7/8 122-300 575 1898

Code No. 5704780 E-8000 J 51 Spare Tips 116

› Straight tips. › Black, tips and lock lever zinc plated. › The toothed bracket stops the pliers legs from

straddling beyond the permitted working area. › This ensures safe working even in hidden

�tting positions.

› Locking pin can be replaced. › Non-crush type release lever with handle

recesses, blue dip insulated. › Precision machined, oil hardened and

annealed. › E-8000 J = pair of spare tips.

B A M N

S 8000 SET OF CIRCLIP PLIERS4 pieces

› Most popular sizes, packed in environmentally friendly cardboard box. › Particularly suitable for barely accessible places. › For internal and external circlip rings. › With straight and 90° angled tips.

Code No. Contents

6701030

S 8000 External: 8000-A2 Straight 8000-A21 AngledInternal: 8000-J2 Straight 8000-J21 Angled

756

S 8003 JC PLIERS SET 841425/27/PL MODULAR FOAM ASSORTMENTS 133

Circlip Pliers Assortment

91

137 GRIP WRENCHES

Code No. O y

640662 137 / 175 25 185 293640670 137 / 250 32 230 546

134 STRAIGHT JAW GRIP WRENCH

› For secure clamping, gripping and holding. › Chrome Vanadium steel 31CrV3. › Nickel plated. › Jaws hardened to 50HRC. Three-point shaped bottom jaw, upper jaw with wire groove. › With adjusting screw and release lever with moulded plastic grip. › Safe release.

› For secure clamping, gripping and holding. › Chrome Vanadium steel 31CrV3. › Nickel plated. › Jaws hardened to 50HRC. › With adjusting screw and release lever with moulded plastic grip. › Safe release.

Code No. O y

745995 134 / 250 25 230 570

Grip Wrenches

503 HANDY 3-PIECE SET 107

B A M N

1101-001 SET OF CIRCLIP PLIERS8 pieces

› Most popular sizes, packed in sturdy plastic case. › Particularly suitable for barely accessible places. › For internal and external circlip rings. › With straight and 90° angled tips. › In Gedore i-BOXX® 72, with transparent cover for easy view.

Code No. Contents

1692275

1101-001 External: 8000-A1 Straight 8000-A11 Angled 8000-A2 Straight 8000-A21 AngledInternal: 8000-J1 Straight 8000-J11 Angled 8000-J2 Straight 8000-J21 Angled

1550

NEW

92

PLIERS

138 WELDER'S GRIP WRENCH

138 Y PROFILE-SECTION GRIP WRENCH

Code No. y

6407350 138 280 960

› For clamping strips and pro�le sections when welding. › Cast steel jaws. › Nickel plated. › Release lever blue dip insulated.

› For clamping bulky pro�le and angle sections. › Strong forged jaws. › GEDORE special chrome-vanadium steel, nickel-plated. › Release lever blue dip insulated.

Code No. O P y

6407860 138 Y 95 75 280 763

Pipe Wrenches

Permit No. 9668 / 15323

SABS System Certification p 8/30/07 10:50 AM Page 2

Composite

C M Y CM MY CY CMY K

227 - AMERICAN PATTERN

DID YOU KNOW?

Gedore heavy duty pipe wrenches are the ONLY pipe wrenches in South Africa with

the SABS certified mark.

Jaw teeth induction hardened.

Spheroidal graphite cast handle.

Drop forged hook, hardened and tempered from selected carbon steel.

Blue epoxy powder coated.

93

Code No. O [ y

645036 225/250 34 1 250 580645044 225/300 44 1.1/4 300 770645052 225/350 49 1.1/2 350 1035645060 225/450 60 1.1/2 450 1630645079 225/600 76 2.1/2 600 3000645087 225/900 102 3.1/2 920 6780

Code No. O y

645303 227/200 34 190 415645311 227/250 49 245 785645344 227/300 55 300 1180645346 227/350 60 320 1625645354 227/450 76 410 2780645362 227/600 90 550 4190645370 227/900 140 800 95956453740 227/1200 210 1040 14500

Code No. 545376 E 227 A / 200 Spring545384 E 227 A / 250 Spring545392 E 227 A / 350 Spring545406 E 227 A / 450 Spring545414 E 227 A / 600 Spring545422 E 227 A / 900 Spring545368 E 227 B / 200 Knurl545430 E 227 B / 250 Knurl545449 E 227 B / 350 Knurl545457 E 227 B / 450 Knurl545465 E 227 B / 600 Knurl545597 E 227 B / 900 Knurl545473 E 227 C / 200 Jaw & Pin545481 E 227 C / 250 Jaw & Pin545503 E 227 C / 350 Jaw & Pin545511 E 227 C / 450 Jaw & Pin545538 E 227 C / 600 Jaw & Pin545635 E 227 C / 900 Jaw & Pin545546 E 227 D / 200 Hook545554 E 227 D / 250 Hook545562 E 227 D / 350 Hook545570 E 227 D / 450 Hook545589 E 227 D / 600 Hook545643 E 227 D / 900 Hook

225 PIPE WRENCHESStillson type

227 PIPE WRENCHESAmerican pattern

› For heavy duty applications. › Drop forged hook, hardened and tempered from selected carbon steel. › Jaw teeth induction hardened. › Spheroidal graphite cast handle. › Blue epoxy powder coated. › In accordance with SANS 1028.

› Drop forged, CHROME VANADIUM handle, hardened and tempered. › Drop forged hook, hardened and tempered from selected carbon steel. › Jaw teeth induction hardened. › Blue epoxy powder coated. › In accordance with SANS 1028.

Code No.

544027 E 225 A / 250 Frame544035 E 225 A / 300 Frame544043 E 225 A / 350 Frame544051 E 225 A / 450 Frame544078 E 225 A / 600 Frame544086 E 225 A / 900 Frame544825 E 225 B / 250 Knurl544833 E 225 B / 300 Knurl544841 E 225 B / 350 Knurl544868 E 225 B / 450 Knurl544876 E 225 B / 600 Knurl544884 E 225 B / 900 Knurl544922 E 225 C / 250 Hook544930 E 225 C / 300 Hook544949 E 225 C / 350 Hook544957 E 225 C / 450 Hook544965 E 225 C / 600 Hook544973 E 225 C / 900 Hook545007 E 225 D / 250 Pin545015 E 225 D / 300 Pin545023 E 225 D / 350 Pin545031 E 225 D / 450 Pin545058 E 225 D / 600 Pin545066 E 225 D / 900 Pin545252 E 225 EF / 250 Rivet & Spring545260 E 225 EF / 300 Rivet & Spring545309 E 225 EF / 350 Rivet & Spring545279 E 225 EF / 450 Rivet & Spring545317 E 225 EF / 600 Rivet & Spring545287 E 225 EF / 900 Rivet & Spring

225 SPARES

227 SPARES

UNIVERSAL PLIERS 95

94

PLIERS

Code No. Pipe Size y

032000 210 / 50 10-60mm 510 1600032005 210 / 75 15-90mm 710 4400032010 210 / 100 27-115mm 950 8000032020 210 / 150 35-165mm 1140 11500032040 210 / 200 45-220mm 1320 13000

Code No. 032049 E 210 B / 50 Pair of Jaws032050 E 210 B / 75 Pair of Jaws032051 E 210 B / 100 Pair of Jaws032052 E 210 B / 150 Pair of Jaws032054 E 210 B / 200 Pair of Jaws

210 PIPE WRENCHChain pipe wrench

› Double sided replaceable serrated jaws. › Selected carbon steel. › Drop forged, heat treated. › Red epoxy powder coated handle.

E 210A SPARE CHAIN

E 210A SPARE JAWS (PAIR)

Code No. Chain Lengths032099 E 210 A / 50 Chain 396mm032100 E 210 A / 75 Chain 478mm032101 E 210 A / 100 Chain 603mm032102 E 210 A / 150 Chain 637mm032104 E 210 A / 200 Chain 1305mm

BOLT CUTTERS 96 TIN SNIPS 97BOLT CUTTERS

95

142 10 JC 142 10 C

Water Pump / Universal Pliers

142 UNIVERSAL PLIERS › According to DIN ISO 8976 Form C. › With safety box joint and protection against blocking. › Fine adjustment. › 142 10 = 15 settings. › Single-hand adjustment for safe clamping.

› Slender pliers head for places that are hard to access. › Long slim jaws. › O�set gripping faces for self-gripping – no slipping o�. › Gedore special Chrome Vanadium steel. › Induction rehardened serrated faces.

› Model C = slim handles with forged serrations. › Model JC = chrome-plated, with 2-component handles › Chrome Vanadium special steel.

143 UNIVERSAL PLIERS6 settings

› According to DIN ISO 8976 Form B. › Slim head. › Forged twin-groove lay-on slip joint and toothed recess. › O�set gripping faces for self-gripping of nuts and pipes. › Pinch protector. › For pipes up to 1.1/2" and nuts up to 38mm. › Chrome Vanadium steel 31CrV3. › Induction hardened teeth. › Model C = slim handles with forged serrations

145 10 C

145 WATER PUMP PLIERS › Chrome Vanadium steel 31CrV3. › Chrome plated. › Pinch protector. › Induction hardened teeth. › 145 10C = 7 settings. › 145 15C = 9 settings.

Code No. O y

6416260 142 10 C 38 250 0.3806416340 142 10 JC 38 260 0.4176416180 142 10 TL 38 255 0.3715537190 E 142 A/10 Spare Screw and Nut

Code No. O y

6410650 143 10 C 38 256 0.3405410600 E 143 A/10 Spare Screw and Nut

Code No. O y

6412000 145 10 C 39 250 0.3656412190 145 15 C 50 375 0.8542962683 E 145 A/10 Spare Screw and Nut

142 10 TL

96

PLIERS

Code No. y 0

2541300 8340 - 200JL 200 0.389

Code No. max. E z y 0

2675137 8178 - 460 5 18 460 1.6802675145 8178 - 620 7 24 620 2.4602675153 8178 - 780 8 30 780 4.7002675161 8178 - 900 9 36 900 5.000

Code No. y 0

2666324 8340Z - 200JL 200 0.389

1.

2.

10 N

10 N

300 N

30 : 1

8340 8340 Z

8340-200 JL

8340 Z-200 JL

Bolt Cutters

8340 / 8340 Z BOLT CUTTERS › Compact power bolt cutters with e�ective cutting performance. › Optimum lever action requires less e�ort. › Wear-free rotating/thrust block bolt to reduce sliding friction when cutting.

› From soft to hard wires up to 4mmØ. › The grooves in the blades prevent sliding while cutting.

› With a two-cut process, from soft to hard wires 4 to 6mmØ. › The extra cutting edge (1) serves as a �rst cut for thick bolts and engraves them. › In the second step, the main cutting edge (2) cuts through the bolt completely.

8340 MINI BOLT CUTTERS › The positioning of the blades close to the joint

creates a particularly e�ective power to cutting ratio. › Blades additionally induction hardened

(63-65HRC).

› Precision cutting edges for soft wire up to 6.0mmØ, hard and piano wire up to 3.8mmØ. › Model JL = steel-grey, with blue dipped handle

protectors.

8340 Z MINI BOLT CUTTERS › Optimum lever action requires less e�ort. › Cutting edges additionally inductively hardened

(63 - 65HRC). › Double-sided milling near the joint ensures best

leverage for thicker wire diameters.

› Precision blades that can cut soft wire up to 6.0mmØ, hard wire up to 5,5mmØ and piano wire up to 3,8mmØ. › Model JL = steel-grey, with blue dipped handle

protectors.

› The e�ective force multiplication ratio of 1:30 near the cutting edge. › Force optimised, cutting near joint is guaranteed.

Code No. 2675196 E 8178 460 Replacement Cutting Head2675218 E 8178 620 Replacement Cutting Head2675226 E 8178 780 Replacement Cutting Head2675234 E 8178 900 Replacement Cutting Head

8178 BOLT CUTTERS

› Accoding to DIN ISO 5743. › Double cam bolt adjustment. › Cutting head replaceable. › Cutters from Chrome Vanadium steel. › Maximum cutting performance 48HRC.

97

Code No. , Wall thickness y 0

4503400 220020 1/8-2” 10-60 2.0-6.3 380 2.90

Code No. 220220 Spare Wheel

Code No. y 0

675504 8516/250 250 0.525675547 8516/300 300 0.675

Code No. y 0

675784 8531/200 Left-hand Cutting 200 0.290675792 8531/250 Left-hand Cutting 250 0.455675806 8531/300 Left-hand Cutting 300 0.660

Code No. y 0

4515410 424-260 Right-hand Cutting 160 530

Code No. y 0

4515760 425-260 Right-hand Cutting 260 480

Pipe Cutter

Tin Snips

8516 scissors pattern

8531 straight pattern

424 ideal pattern snips

425 figure snips

› American Pattern. › Carbon steel SAE1045. › Drop forged and heat treated.

› Cutting surfaces induction hardened. › Precision ground cutters. › Blue epoxy powder coated.

› English Pattern. › Carbon steel SAE1045. › Drop forged and heat treated.

› Cutting surfaces induction hardened. › Precision ground cutters. › Blue epoxy powder coated.

› For straight continuous and �gure cuts. › With lever action. › Self-opening with installed spring and lock. › Polished cutting edges.

› Sheet thickness maximum 1.2mm at strength of 600N/mm2. › Non-slip two-component handles.

› For straight continuous and �gure cuts. › With lever action. › Self-opening with installed spring and lock. › Polished cutting edges.

› Sheet thickness maximum 1.2mm at strength of 600N/mm2. › Non-slip two-component handles.

220 for steel pipes

› Heavy duty pipe cutters. › Frame in malleable cast steel. › TUBEX®

AUTOMOTIVE TOOLS / KITS

98

AUTOMOTIVE TOOLS

TYRE FITMENT TOOLS

100

PISTON / VALVE TOOLS

104

MEASURING TOOLS

106

FILTER / SPARK PLUG TOOLS

102

SPECIAL PLIERS

105

SAWS

107

LIFTERS

103

TOOLKITS

112

BRAKE TOOLS

105

26R DOUBLE ENDED BOX SPANNERS

› In tubular steel, hardened. › Chrome plated.

26RS STEPPED TOMMY BAR

KD-26R BOX SPANNER SET7 pieces

› Chrome Vanadium steel 31CrV3, hardened. › Chrome plated.

100

AUTOMOTIVE TOOLS

Code No. y

6210050 26R 6x 7 105 286210210 26R 8x 9 110 356210640 26R 10x 11 120 456210990 26R 12x 13 140 756211370 26R 14x 15 140 906211610 26R 16x 17 150 1206211880 26R 17x 19 160 180

Code No. y

652806 26RS 1 - Fits 26R 6x7 - 10x11 190 40652814 26RS 2 - Fits 26R 12x13 - 16x17 240 140652822 26RS 3 - Fits 26R 17x19 - 36x41 330 500

Code No. y

6211960 26R 18x 19 160 1806212260 26R 20x 22 170 2106212340 26R 21x 23 170 2156212690 26R 24x 27 190 3006212770 26R 25x 28 200 3506213070 26R 30x 32 200 3806213310 26R 36x 41 220 650

Code No. Contents Accessories 0

621846 KD-26R 8x9 10x11 12x13 14x15 16x17 18x19

26RS 2 Tommy Bar 0.685

STUD EXTRACTOR 196PULLERS 193

Box Spanners

27 WHEEL SOCKET WRENCH

28 4-WAY WHEEL WRENCH

› Chrome Vanadium steel 31CrV3. › Chrome plated.

› Chrome Vanadium steel 31CrV3. › Blue epoxy powder coated.

38 / 39 TYRE LEVERS

› Chrome Vanadium steel 31CrV3. › Drop forged. › 38 = Chrome plated. › 39 = Blue epoxy powder coated.

39

38

101

Code No. Size y 0

622761 28 PU 17x19 21x22 420x420 1360622869 28 CV 19x20 24x27 595x583 36906229150 28 LV 34.5x38 45x25.3 4900

Code No. y 0

026050 27-22x24 19 500 1700026060 27-24x27 19 500 1800026150 27-27x30 19 500 2300026155 27-27x32 21 500 2300026156 27-27x33 21 500 2300026165 27-30x32 21 500 2300026168 27-30x33 21 500 2300026170 27-32x33 21 500 2400026175 27-21x38 19 500 2300026180 27-21x41 21 500 2500

026052 27d/35d-19 (19.05mmx500) 19 500 1095026152 27d/35d-21 (20.89mmx500) 21 500 1300

Code No. y 0

633267 38 / 400 400 0.458633283 38 / 500 500 0.576633305 39 / 610 610 1.463

139 PRY BARS

› Chrome Vanadium steel 31CrV3. › Drop forged. › 38 = Chrome plated. › 39 = Blue epoxy powder coated.

Code No. y 0

1396596 139 - 350X13 Pry Bar 350 0.3961396597 139 - 350X19 Pry Bar 350 0.7971396598 139 - 450X19 Pry Bar 450 1.02

Pry Bars

IMPACT SOCKETS 56

NEW

Wheel Wrenches

Tyre Levers

36 OIL FILTER STRAP WRENCH › Chrome Vanadium steel 31CrV3. › Chrome plated. › Strong wide strap. › Light duty.

1.75 OIL FILTER HOOK › Three-arm pattern. › For removing �rmly seated oil �lters.

50 SPARK PLUG SOCKET › Chrome Vanadium steel 31CrV3. › Chrome plated. › To be used in conjuction with 1/2” drive socket accessories.

54 SPARK PLUG SOCKET › Chrome Vanadium steel 31CrV3. › Chrome plated. › To be used in conjuction with 1/2” drive socket accessories.

55 SPARK PLUG SPANNER

58 SPARK PLUG SPANNER

› Chrome Vanadium steel 31CrV3. › Chrome plated. › Hot forged socket head with plug retainer, swivel joint. › Handle with blue PVC sleeve.

› Chrome Vanadium steel 31CrV3. › Hot forged socket head with plug retainer. › Chrome plated. › Swivel joint.

102

AUTOMOTIVE TOOLS

Code No. y

6327320 36 / 1 220 3076327400 36 / 2 285 4705327380 E 36 / 1 Strap5327460 E 36 / 2 Strap

Code No. y

8117420 1.75/1 60-120 600

Code No. y

636614 50/20,8mm-13/16 63 119Code No. y

636622 54 / 16mm 63 96

Code No. y

636606 55 / 20,8mm 238 298

Code No. y

636355 58 / 16mm 301 330636339 58 / 20,8 mm 500 340636347 58 / 16 & T-Bar 301 455636312 58 / 20,8 & T-Bar 500 465636320 58 Tommy Bar 199 125

Filter Tools

Spark Plug Tools

647 SPARK PLUG BRUSH

› With plastic handle and brass wire bristles.

103

Code No. Bristle Length y

6531950 647 15mm 180 22

121 G SUCTION CUP LIFTER

› Two hinged suction heads with safety locking. › Oil and acid resistant ABS plastic. › Lifting capacity approximately 80kg.

121 G-3 SUCTION CUP LIFTER

› Three hinged suction heads with safety locking. › Oil and acid resistant ABS plastic. › For curved glass and panels. › Lifting capacity approximately 120kg.

Code No. , y 0

6391170 121 G 120 390 1.25Code No. , 0

6390870 121 G-3 120 1.27

642 SP MAGNETIC LIFTERwith lamp, mirror and clip

640 MAGNETIC LIFTER

› For searching and lifting small metal parts in con�ned areas. › Magnet can be removed if necessary. › Mirror diameter 30mm.

› With �exible shaft and plastic handle. › Bright nickel plated.

Code No. Diameter of magnet y

6536750 642 SP 12mm 500 172

Code No. Diameter of magnet y

6531280 640 12mm 520 230

Lifters

125 PISTON RING CLAMP BAND

› Made from special spring strip steel with continuous adjustment. › With tightening key.

126-060 PISTON RING PLIERS

› For secure �tting of piston rings. › With prism holder and adjusting screw.

Code No. , y 0

6396800 125-1 57-125 80 0.3106396990 125-2 90-175 80 0.3506397020 125-3 90-175 165 0.650

Code No. , y 0

6397100 126 0-60 30-60 210 0.160

126 PISTON RING PLIERS

› For secure �tting of piston rings. › Handles with blue sleeves.

128 VALVE SPRING TENSIONER

› For overhead valve engines with one each straight and o�set pair of hooks. › Bright nickel plated. › Type 2-225 handle with blue sleeve.

Code No. O y 0

6397370 126 1-100 55-100 200 0.2506397450 126 2-120 80-120 240 0.410

Code No. , y 0

6398500 128 2-225 60-225 290 1.206398690 128 1-280 120-280 390 3.25

104

AUTOMOTIVE TOOLS

Pistons / Valves / Special Pliers

132 HOSE CLAMP PLIERS

132 CLIC CLIC HOSE CLAMP PLIERS

› For self-clamping hose clips. › Chrome plated handles.

› For CLIC-R hose clamps. › Polished, bright nickel plated, joint gunmetal �nished. › Forged for clip sizes 5-30mm.

Code No. y 0

6399900 132-220 220 0.215

Code No. y 0

1396714 132-180 180 0.247

8134 INSTALLATION PLIERS

8276 BALANCE WEIGHT PLIERS

› Chrome Vanadium steel 31CrV3. › Chrome Vanadium steel 31CrV3.

Code No. y 0

6722030 8134-170C 170 0.200

Code No. y 0

6739350 8276-250C 250 0.315

› Chrome Vanadium steel 31CrV3. › For drum brakes. › With special holder and support crown, especially suitable for adhesive brake linings. › Chrome plated.

Code No. y 0

6405300 135 - 13 330 0.3706405490 135 -19 480 0.850

105

135 BRAKE SPRING PLIERS

Brake Tools

› With protective handle. › Handle nickel plated. › Folding. › Blade length 100mm.

702 FEELER GAUGE SET

106

AUTOMOTIVE TOOLS

Code No. Contents 0

6547790 702 13 M 5 10 15 20 25 30 40 50 60 70 80 90 100 0.0656547870 702 20 M 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 0.100 6547950 702 21 M 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 0.0686548680 702 13 A .002AF .003AF .004AF .005AF .006AF .008AF .010AF .012AF .015AF .020AF .025AF .030AF .035AF 0.0556548760 702 22 A .004 - .025 increasing by 1/1000” 0.0816548840 702 26 A .0015 - .025 increasing by 1/1000” 0.080

STEEL RULER 300MM

ENGINEERS SQUARE

Code No. Blade Length y 0

0110100 Engineers Square - 75mm 75 0.1150110200 Engineers Square - 100mm 100 0.1330110300 Engineers Square - 150mm 150 0.288

Code No. y q 0

0134000 Measuring Rule - 150mm 150 6 0.0500134100 Measuring Rule - 300mm 300 12 0.0600134300 Measuring Rule - 600mm 600 24 0.120

› Stainless steel with polished �nish. › Permanently engraved. › Metric to imperial conversion table on reverse side.

› Hardened blade. › Accurately ground blade and stock ensures

straightness and parallelism. › Accurate right angles on inside and outside. › Ideal for setting up and checking machinery.

PRECISION ENGINEERING TOOLS

INSIDE SPRING CALIPERINSIDE SPRING CALIPER

Code No. y q 0

0141100 Outside Spring Caliper 100 4 0.0800141200 Outside Spring Caliper 150 6 0.1330141300 Outside Spring Caliper 200 8 0.1800141400 Outside Spring Caliper 250 10 0.2500141500 Outside Spring Caliper 300 12 0.260

Code No. y q 0

0142000 Spring Divider 75 3 0.0800142100 Spring Divider 100 4 0.0800142200 Spring Divider 150 6 0.1330142300 Spring Divider 200 8 0.1800142400 Spring Divider 250 10 0.267

Code No. y q 0

0140100 Inside Spring Caliper 100 4 0.???0140200 Inside Spring Caliper 150 6 0.1330140300 Inside Spring Caliper 200 8 0.1800140400 Inside Spring Caliper 250 10 0.2400140500 Inside Spring Caliper 300 12 0.260

OUTSIDE SPRING CALIPER SPRING DIVIDER

NEW

NEW NEW

Measuring Tools

107

NEW

NEW

NEW

403 HACKSAW

407 HACKSAW

› Adjustable tubular steel frame. › For 10” and 12” hacksaw blades. › Shatterproof blades.

› Pressure cast aluminium. › Ergonomic soft rubber grips. › Adjust saw blade by turning blue clamping element in the hand grip.

Code No. y 0

039010 403 435 0.3605500350 403A Hacksaw Blade 24TPI - Pack of 10 300 0.120

Code No. 0

1879375 407 0.650

Saws

JUNIOR HACKSAW

› Powder coated, steel wire frame. › Easy blade replacement. › Shatterproof blade. › Finger guard prevents injury.

Code No. 0

3012000 Junior Hacksaw 0.083

Code No. y 0

0321001 Engineers Scriber 190 0.045

ENGINEERS SCRIBER

› Double-ended with one straight point and the other at 90 degrees. › Ideal for use in con�ned spaces.

› Protection from unwanted scratches, dents and dirt. › Magnetic attachment keeps paintwork safe from damage – also attaches to galvanised steel. › Rugged, padded imitation leather and reinforced edges provide a perfect, cushioned working area. › Dimensions: 1100x650mm with wheel cut-out to allow easy acccess.

907 FENDER PROTECTOR

› Dome shaped body. › Brass suction pump. › Heavy gauge tin. › Powder coated. › Pump has two ball valves. › No spring on the bottom suction

valve prevents malfunctioning.

108

AUTOMOTIVE TOOLS

Code No. y 0

1942956 907 1100 0.620

SAFETY GLASSES

› Euro type spectacles, polycarbonate lens CE (EN 166-2001). › Clear anti-scratch lens.

Code No. 0

200638 DV026C Safety Glasses & Bag 0.035

4530 TOWROPE

Code No. y 0

669776 4530- 2 Ton 3500 0.310669806 4530- 4 Ton 3500 1.70

299 DRAIN PLUG SPANNER › Chrome Vanadium steel 31CrV3. › Chrome plated. › For square bungs on engine pumps, tanks and drums for oil and chemicals. › Five square sizes: 8.7 9.5 10.5 11.5 13mm › Four tapered sizes: 6.8-8.7 10.5-13 15.2-18 16.5-19mm › One screwdriver blade: 5.5 x 18mm

Code No. y 0

6464580 299 220 0.450

BRASS PUMP OIL CAN

G-CLAMPS

Code No. y q 0

3580000 G-Clamp 75 3 0.5003580100 G-Clamp 100 4 0.9003580200 G-Clamp 150 6 1.4003580300 G-Clamp 200 8 1.500

Code No. Capacity (ml) 0

4163300 Brass Pump Oil Can 500 0.278

NEW

Miscellaneous

NEW

109

Basic Toolsets

503 HANDY 3-PIECE SET3 pieces

› Practical set composition in environmentally-friendly cardboard box › JC = chrome-plated, with 2-component handles

Code No. Contents 0

651133 50362-200 Shifting Spanner8250-200 JC Combination Pliers137-250 Vice Grip

1.52

505 BASIC HOME TOOLSET5 pieces

› Practical set composition in environmentally friendly cardboard box. › JC = chrome plated, with 2-component handles.

Code No. Contents 0

651141 505 62-200 Shifting Spanner8250-200 JC Combination Pliers137-250 Vice Grip2150 4-1502160 PH2

3.30

110

AUTOMOTIVE TOOLS

Waist Pouch

See pg. 228 for complete Rucksack Toolset.

› Fabric construction in 600D polyester canvas. › Water repellent and durable. › Toolbag: 38mm reinforced polypropylene webbing straps. › Waist Pouch: 25mm reinforced polypropylene webbing straps. › YKK zip and nickel rivets for additional reinforcing. › Reinforced loops for screwdrivers and pliers.

Code No. 0

545200 Zipped Tool Bag 0.350

Code No. 0

545210 Waist Pouch 0.200

TOOLS NOT INCLUDED

Code No. 0

545220 Tool case - EMPTY 2.25

TOOLS NOT INCLUDED

Code No. 0

545190 Rucksack - EMPTY 1.00

See pg. 223 for complete Electrcians Toolset.See pg. 223 for complete Electrcians Toolset.See pg. 223 for complete Electrcians Toolset.See pg. 223 for complete Electrcians Toolset.

Zipped Tool Bag

Tool Bags

TOOL BELTS TOOL BAG / WAIST POUCH

› Double stitched and bound. › Very durable water repellent inner lining. › Heavy duty zip. › Reinforced inners.

ELECTRICIAN‘S TOOL CASE

› 600x600D water repellent polyester fabric. › Double stitched and bound. › 10cf-thick extra heavy duty zip. › Three front velcro-closing pockets with re�ective strip. › Inside detachable divider with fabric sleeves to hold tools with clear velcro sleeve cover. › Reinforced padded back with reinforced padded back straps.

TOOL RUCKSACK

111

› High quality tear resistant fabric made from 600D polyester. › Strong industrial seams. › Universal size with four lateral buckles for resizing. › One back pocket with zips. › Two right-hand pockets and four left-hand pockets. › Elastic screwdriver holder. › Re�ector strips front and back for improved visibility.

Code No. 0

1818260 Tool Jacket 0.730

Code No. 0

1938614 9210 12 (XXL) 0.080

TOOL JACKET

› For universal use. › Close �tting for retention of feel and dexterity. › Kind on the skin. › Rugged imitation leather and synthetic material. › Stage 5 classi�cation as per EN 420/03 (scale from 0-5).

TOOL BOXES 116 TOOL ASSORTMENTS 119

920 WORK GLOVES

112

AUTOMOTIVE TOOLS

SORTIMO GENERAL TOOL ASSORTMENT39 pieces

› Dimensions: L=442 x W=357 x H=151mm.

Code Contents 0

677001 9.06Allen KeysScrewdrivers

Sockets

42-88M 2 2.5 3 4 5 6 8 102150 6.5 5.5-1502160 PH1 PH2 PH3D19 10 11 12 13 14 15 16 17 18 19 21 22 24

Accessories145-250 Waterpump Pliers95-200 Flat Cold ChiselVoltage Tester 140-2K1993U-10T Reversible Ratchet1987 Sliding T-bar

8601-500 Ball Pein Hammer

8250-200 JC Combination Pliers8316-200 JC Side Cutters1990-125 Extension1990-250 ExtensionNo.62 Adjustable Wrench - 200mm

SMALL LEISURE BOAT TOOLKIT11 pieces

› Toolkit �oats. › Tools as recommended for category ‘R’ – estuary and internal waters. › Nine pieces in a splash-proof bag.

Code Contents 0

668096 2.62Screwdrivers 2150 6.5

2160 PH2

Accessories26RST x 175 Socket & T-Bar60CP-250 Shifting Spanner145/250 Universal Pliers4530 Tow Rope – 2-Ton

8250/200 JC Combination PliersTorch – Hiker’s HeadlampLeather Gloves

5017 JAZZ TOOL ASSORTMENT59 pieces

› Dimensions: L=440 x W=400 x H=100mm.

Code Contents 0

677010 9.12SpannersAllen KeysScrewdrivers

Sockets

No.7 10 11 12 13 14 15 16 17 1942-88M 2 2.5 3 4 5 6 8 102150 3-150 4-150 6.5 2160 PH1 PH2C19 10 11 12 13 14 15 17 19 22 24 No.20 5 6 7 8 9 10 11 12 13

Accessories1993 Z-94 Ratchet 2093 Z-94 Ratchet2087 Sliding T-Bar2088 Flexible Extension2090-4 ExtensionVoltage Tester 140-2K137-250 Grip Pliers8601-500 Ball Pein Hammer

1990-250 Extension1990-125 Extension1995 Universal Joint55/20.8 Spark Plug Spanner2090-6 Extension145-250 Universal Pliers8250 200JC Combination Pliers

113

CARAVAN TOOLKIT20 pieces

› In a black canvas case with zip fastener.

Code Contents 0

668098 4.13SpannersScrewdrivers

1B 10 11 13 14 17 192150 3-150 6.52160 PH1 PH2

Accessories26R 17x19 Box Spanner8250/200 JC Combination Pliers137-250 Grip Pliers9930 TorchLeather Gloves

26R Tommy-Bar60CP-250 Shifting Spanner8316/200 JC Side CuttersRe�ective Vest

502 MOTORIST TOOLKIT24 pieces

› In a black canvas case with zip fastener and carry strap.

Code Contents 0


Sockets

NO.6 10x11 12x13 14x15 16x17 19x222150 6.5 3-1502160 PH1 PH2C19 10-3/8 12 13-1/2 17 19-3/4 22

Accessories1990/125 Extension1993U-10K Plastic Ratchet9534-05 Tape Measure9930 Torch

62/200 Adjustable Wrench145/250 Universal Pliers4530 Tow Rope – 2-Ton9999.900 Multifunction Pliers

507 LEISURE MOTORIST TOOLKIT15 pieces

› In a black canvas case with zip fastener.

Code Contents 0


NO.6 8x9 10x11 12x13 14x15 16x17 19x222150 6.5 2160 PH2

Accessories26RST x 175 Socket & T-Bar60CP-250 Shifting Spanner145/250 Universal Pliers

Re�ective VestLeather Gloves

114

SHEETMETAL / TOOL ASSORTMENTS

SHEETMETAL

TOOL ASSORTMENTS

TOOLBOXES / TRAYS / TRUNKS

116

VICES

129

TOOL CHESTS

130

ASSORTMENTS / CABINETS

119

TOOL PANELS

129

ARTISANS WORKSTATIONS

128

DRAWER UNITS

129

MODULAR ASSORTMENTS

134

TOOL TROLLEYS

132

Code No. 0

660868 1260 4.70

Code No. 0

660876 1261 6.20

1261 TOOLBOX5 compartments

› With riveted joins. › Strong structure, smooth and easy opening and closing. › Maximum access to bottom tray. › Lockable, phosphated and powder coated to prevent corrosion. › L=460 x W=248 x H=220mm.

Code No. 0

660957 1282/5 7.50

1282 / 5 TOOLBOX5 compartments

› With riveted joins. › Strong structure, smooth and easy opening and closing. › Maximum access to bottom tray. › Plastic Handle: ZA Registration Design 2005/0507. › Lockable, phosphated and powder coated to prevent corrosion. › L=400 x W=248 x H=220mm. › Designed to accommodate all modular kits.

116


Toolboxes


› With riveted joins. › Strong structure, smooth and easy opening and closing. › Maximum access to bottom tray. › Lockable, phosphated and powder coated to prevent corrosion. › L=460 x W=248 x H=173mm.

Code No. 0

660949 1281 6.50


› Robust, rust-free, rounded corners. › Cast-in lid hinges with non-removeable pins. Lockable. › Plastic Handle: ZA Registration

Design 2005/0507. › Phosphated and powder coated

to prevent corrosion. › L=460 x W=240 x H=220mm.

Code No. 0

661058 1335 6.00


› With riveted joins › Strong structure, smooth and

easy opening and closing. › Maximum access to bottom tray. › Lockable, phosphated and

powder coated to prevent corrosion. › L=550 x W=248 x H=220mm.

Code No. 561347 1280/81-7M INS561134 1280/81-1B INS561169 1280/81-1B AF INS561142 1280/81-DI9 INS561126 1280/81-D19ACC INS561185 1280/81-22-ACC INS561193 1281/82-1B 62H INS561207 1280/81-D19/IN19 INS561215 1280/81-D19 ACC/SKT INS561258 1280/81-D32/6 INS561274 1280/81-PL/137/36 INS561282 1282-SD-PH-STB INS561290 1282-SD-MEC-EL INS561304 1282-4/ACC INS561312 1282 - EXT INS561320 1282 - 6SD INS561339 1282 - UTILITY INS561355 1282 - D20 EZ INS561363 1282 - PLIER INS561371 1282 - 1B 18 INS561398 1282 - 8601 ACC INS

TRAYSSHEETMETAL TRAYS

VACUUM MOULDED INSERTS

› Inserts Fit Into: 1281 / 1282 Toolboxes 1425 Tool Chest 1575 / 1581 Tool Trolleys 1502 Drawer Unit 1401 / 1404 Tool Cabinets

INSERTS

Code No. 561150 1280/81 - Metal Tray561266 1280/81 - D32 Metal Tray561401 1282 - Metal Tray561428 1282 - D32 Metal Tray

› Trays Fit Into: 1280 / 1281 / 1282 Toolboxes

MODULAR ASSORTMENTS 134

117

Die-cast Aluminium Toolbox

Tool Trunks

1460 / 1460L TOOL TRUNKS

› Strong structure, smooth operating hinges. › Lockable. › Phosphated and powder coated to prevent corrosion. › 1460: Silver galvanized tray is purchased separate. › 1460: Nests. › 1460 L: 4x4 tool trunk. › 1460 L: With tray. › 1460L: Chrome plated re-inforced corner pieces.

Code No. L H W 0

663837 1460-59 587 252 203 7.0663839 1460-65 651 284 280 7.0663840 1460-65S 651 284 280 7.0663841 1460-70 717 314 388 10.0663843 1460-80 801 379 471 14.0663844 1460-80S 801 379 471 14.0663845 1460-91 910 431 554 14.0

1460 TRAYS

Code No. L H W 0

663856 1460-59 Tray 341 58 172 0.95663857 1460-65 Tray 341 58 249 1.17663858 1460-70 Tray 341 58 357 1.70663860 1460-80 Tray 341 58 439 1.90 663861 1460-91 Tray 341 58 524 2.20

MODULAR ASSORTMENTS 133 MODULAR ASSORTMENTS 136

118


Code

663837663839663840663841663843663844

12

34

5

1460-91

Tool Assortments

1281-C19-1BM TOOL ASSORTMENT65 pieces

d

1281 / 1282-C19-1BM-62H TOOL ASSORTMENT77-79 pieces

Code No. 1B Spanners Allen Keys Screwdrivers Toolbox / Inserts / Tray C19 Sockets Accessories 0

678511679003

1281-C19-1BM-62H1282-C19-1BM-62H

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 sockets5 6 8 10 12 14

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1281 / 1282 Toolbox1281/82-1B/62H Insert1280/81-D19/IN19 Insert1280/81-D19 ACC/SKT Insert1282-SD-PH-STB Insert1282-SD-MEC-EL Insert1281 - 1280/81 Tray1282 - 1282 Tray

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug Socket143/250 Universal Pliers1990-75 Extension1990-125 Extension 1990-250 Extension 1995 Universal Joint62/250H Adjustable Wrench1987 Sliding T-Bar1993U-10T Ratchet

16.0017.00

d

Code No. 1B Spanners 42-88M Allen Keys Screwdrivers Toolbox / Inserts / Tray C19 Sockets Accessories 0

678155 1281-C19-1BM 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

2 2,5 3 4 5 6 8 10

215045.56.582160PH1PH2

1281 Toolbox1280/81 D19 ACC Insert1280/81 1B Insert1280/81 D19 Insert1280/81 Tray

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4

50/20.8 Spark Plug Socket145/250 Universal Pliers1990-75 Extension1990-125 Extension1990-250 Extension137/250 Grip Pliers 1987 Sliding T-Bar 1993U-10T Rev. Ratchet1997/375 Power Bar1995 Universal Joint

15.86

119

Die-cast Aluminium

Die-cast Aluminium

1281 / 1282-D19-1BM-62H TOOL ASSORTMENT77-79 pieces

Code No. 1B Spanners Allen Keys Screwdrivers Toolbox / Inserts / Tray D19 Sockets Accessories 0

678554679070

1281-D19-1BM-62H1282-D19-1BM-62H

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 sockets5 6 8 10 12 14

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1281 / 1282 Toolbox1281/82-1B/62H Insert1280/81-D19/IN19 Insert1280/81-D19 ACC/SKT Insert1282-SD-PH-STB Insert1282-SD-MEC-EL Insert1281 - 1280/81 Tray1281 - 1282 Tray

8 10 11 12 13 14 15 16 17 19 21 22 23 24 26 27 28 30 32 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug Socket143/250 Universal Pliers1990-75 Extension1990-125 Extension 1990-250 Extension 1995 Universal Joint62/250H Adjustable Wrench1987 Sliding T-Bar1993U-10T Rev. Ratchet

16.0017.00

Die-cast Aluminiumd

1281-D19-1BA-U3 TOOL ASSORTMENT71 pieces

Die-cast Aluminium d


678597 1281-D19-1BA-U3 1/4AF 5/16AF 3/8AF 7/16AF 1/2AF 9/16AF 5/8AF 11/16AF 3/4AF 13/16AF 7/8AF 15/16AF 1. AF

42-88P 3/32AF 1/8AF 5/32AF 3/16AF 7/32AF 1/4AF 5/16AF 3/8AF

IN19 sockets3/16AF 1/4AF 5/16AF 3/8AF 1/2AF 9/16AF

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1281 Toolbox1280/81-1B AF. Insert1280/81-D19 ACC Skt Insert1280/81-D19/IN19 Insert1280/81 Tray

5/16AF 3/8AF 13/32AF 7/16AF 1/2AF 9/16AF 19/32AF 5/8AF 11/16AF 3/4AF 25/32AF 13/16AF 7/8AF 15/16AF 1. AF 1.1/16 1.1/8 1.3/16 1.1/4

50/20.8 Spark Plug Socket142/250 Universal Pliers137/250 Grip Pliers702/13 A Feeler Gauge Set1987 Sliding T-Bar1990-75 Extension 1990-125 Extension 1990-250 Extension 1995 Universal Joint1993U-3 Rev. Ratchet

16.22

120


1282-C19-1BM-62H-PL TOOL ASSORTMENT78 pieces

d


679240 1282-C19-1BM-62H-PL 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 sockets5 6 8 10 12 14

215045.56.582160PH1PH2

1282 Toolbox1281/82-1B/62H Insert1280/81-D19/IN19 Insert1280/81-D19 ACC/SKT Insert1282 - 6SD Insert1282 - pliers Insert1282 Tray

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug Socket62/250H Adjustable Wrench143/250 Universal Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension 1990-250 Extension 1995 Universal Joint1993U-10T Rev. Ratchet

Pliers8132-200 JC Telephone Pliers8250-200 JC Combination Pliers8316-200 JC Side Cutters

18.50

1282-D19-1BM-62H-PL TOOL ASSORTMENT78 pieces

d


679267 1282-D19-1BM-62H-PL 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 sockets5 6 8 10 12 14

215045.56.582160PH1PH2

1282 Toolbox1281/82-1B/62H Insert1280/81-D19/IN19 Insert1280/81-D19 ACC/SKT Insert1282 - 6SD Insert1282 - pliers Insert1282 Tray

8 10 11 12 13 14 15 16 17 19 21 22 23 24 26 27 28 30 32 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug Socket62/250H Adjustable Wrench143/250 Universal Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension 1990-250 Extension 1995 Universal Joint1993U-10T Rev. Ratchet


18.50

121

1282-C19Z-1BM-62H TOOL ASSORTMENT79 pieces

With high-density foam inserts

d


679119 1282-C19Z-1BM-62H 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 sockets5 6 8 10 12 14

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1282 Toolbox1281/82-1B/62H Insert1280/81-D19/IN19 Insert1280/81-D19 ACC/SKT Insert1282-SD-PH-STB Insert1282-SD-MEC-EL Insert1282 Tray

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug Socket143/250 Universal Pliers62/250H Adjustable Wrench1987 Sliding T-Bar1990-75 Extension1990-125 Extension 1990-250 Extension 1995 Universal Joint1993Z-94 Ratchet +Coupler

18.50

1282-C19-1BMZ-PL-6SD TOOL ASSORTMENT67 pieces

d


679232 1282-C19-1BMZ-PL-6SD

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

215045.56.582160PH1PH2

1282 Toolbox1280/81-DI9 Insert1280/81-1B Insert1282 - ext Insert1282 - 6SD Insert1282 - pliers Insert1282 Tray

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4

137/250 Grip Pliers 145/250 Universal Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension1990-250 Extension 1993Z-94 Ratchet + Coupler


18.00

122


With high-density foam inserts

1282-D19-1BMZ-PL-6SD TOOL ASSORTMENT67 pieces

d

1282-C19-1BMZ-10SD TOOL ASSORTMENT68 pieces

d


679259 1282-D19-1BMZ-PL-6SD

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

215045.56.582160PH1PH2

1282 Toolbox1280/81-DI9 Insert1280/81-1B Insert1282 - ext Insert1282 - 6SD Insert1282 - pliers Insert1282 Tray

8 10 11 12 13 14 15 16 17 19 21 22 23 24 26 27 28 30 32

137/250 Grip Pliers145/250 Universal Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension1990-250 Extension 1993Z-94 Ratchet + Coupler


18.50

Code No. 1B Spanners Allen Keys Screwdrivers Toolbox / Inserts / Tray C19 Sockets (679135) Accessories 0

679135679291

1282-C19-1BMZ-10SD 1282-D19-1BMZ-10SD

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1282 Toolbox1280/81-DI9 Insert1280/81-1B Insert1282 - ext Insert1282-SD-PH-STB Insert1282-SD-MEC-EL Insert1282 Tray

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4

D19 Sockets (679291)8 10 11 12 13 14 15 16 17 18 19 21 22 24 26 27 29 30 32

137/250 Grip Pliers145/250 Universal Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension1990-250 Extension1993Z-94 Ratchet + Coupler

19.5019.50

123

1281-C19/22-1BA-U3 TOOL ASSORTMENT68 pieces

d


678589 1281-C19/22-1BA-U3 1/4AF 5/16AF 3/8AF 7/16AF 1/2AF 9/16AF 5/8AF 11/16AF 3/4AF 13/16AF 7/8AF 15/16AF 1.AF

42-88P 3/32AF 1/8AF 5/32AF 3/16AF 7/32AF 1/4AF 5/16AF 3/8AF

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1281 Toolbox1280/81-1B AF. Insert1280/81-DI9 Insert1280/81-22 ACC Insert1280/81 Tray

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug Socket137/250 Grip Pliers141/250 Universal Pliers1987 Sliding T-Bar1990-75 Extension 1990-125 Extension 1990-250 Extension1997/375 Power Bar 1995 Universal Joint1993U-3 Rev. Ratchet

16.42

1281/1282-C19/22-1BM-10SD TOOL ASSORTMENT72-74 pieces

d


678538679011

1281-C19/22-1BM-10SD1282-C19/22-1BM-10SD

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 sockets5 6 8 10 12 14

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1281/1282 Toolbox1281/2 1280/81-1B Insert 1280/81-D19 Insert 1280/81-22-ACC Insert1282 1282-SD-PH-STB Insert1282-SD-MEC-EL Insert1280/81 Tray1282 Tray

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug Socket137/250 Grip Pliers145/250 Universal Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension 1990-250 Extension 1997/375 Power Bar1995 Universal Joint1993U-10T Rev. Ratchet

16.5018.50

Die-cast Aluminium

Die-cast Aluminium

124


1281/1282-D19/22-1BM-10SD TOOL ASSORTMENT72-74 pieces

d


678546679089

1281-D19/22-1BM-10SD1282-D19/22-1BM-10SD

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1281/1282 Toolbox1281/2 1280/81-1B Insert 1280/81-D19 Insert 1280/81-22-ACC Insert1282 1282-SD-PH-STB Insert1282-SD-MEC-EL Insert1280/81 Tray1282 Tray

8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 26 27 28 29 30 32

50/20.8 Spark Plug Socket137/250 Grip Pliers145/250 Universal Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension 1990-250 Extension 1997/375 Power Bar1995 Universal Joint1993U-10T Rev. Ratchet

16.5018.50

Die-cast Aluminium

1281/1282-C32/19-1BM-62H TOOL ASSORTMENT88-90 pieces

d

e

Code No. 1B Spanners Allen Keys Screwdrivers Toolbox / Inserts / Tray C19 / C32 Sockets Accessories 0

678740679038

1281-C32/19-1BM-62H1282-C32/19-1BM-62H

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 sockets5 6 8 10 12 14

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1281/1282 Toolbox1281/2 1281/82-1B/62H Insert 1280/81-D19/IN19Insert 1280/81-D19 ACC/SKT Insert1280/81-D32/6 Insert1282 1282-SD-PH-STB Insert1282-SD-MEC-EL Insert1280/81 - D32 Tray1282 - D32 Tray

C19 8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4 7/16AF 9/16AF 7/8AF

C32 1.3/8AF 36-1.7/16 38-1.1/2 41-1.5/8 46-1.13/16 50-2.

50/20.8 Spark Plug Socket62/250H Adjustable Wrench143/250 Universal Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension 1990-250 Extension 1995 Universal Joint1993U-10T Rev. Ratchet3287/447 Sliding T-Bar3290-200mm Extension3290-400mm Extension3293U-1/440 Ratchet

25.5026.50

Die-cast Aluminium

125

1282-D32/19-1BM-62H TOOL ASSORTMENT90 pieces

d

e

Code No. 1B Spanners Allen Keys Screwdrivers Toolbox / Inserts / Tray D19 / D32 Sockets Accessories 0

679097 1282-D32/19-1BM-62H 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 5 6 8 10 12 14

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1282 Toolbox1280/81-1B/62H Insert1280/81-D19/IN19 Insert1280/81-D19 ACC/SKT Insert1280/81-D32/6 Insert1282-SD-PH-STB Insert1282-SD-MEC-EL Insert1282 - D32 Tray

D19 8 10 11 12 13 14 15 16 17 19 21 22 23 24 26 27 28 30 32 7/16AF 9/16AF 7/8AF

D32 34 36 38 41 46 50

50/20.8 Spark Plug Socket62/250H Adjustable Wrench143/250 Universal Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension 1990-250 Extension 1995 Universal Joint1993U-10T Rev. Ratchet3287/447 Sliding T-Bar3290-200mm Extension3290-400mm Extension3293U-1/440 Rev. Ratchet

25.61

Tool Cabinets

1401 / 1401 PRO TOOL CABINET / ASSORTMENT76 pieces

d

Code No. 1B Spanners Allen Keys Screwdrivers Tool Cabinet C19 Sockets Accessories 0

661163 1401 PRO - With Accessories and Tools

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 5 6 8 10 12 14

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1401

Accessories30 x Plastic Holders with Pins1 x Tool Rack: 17-Pin1 x Double Storage Tray1 x Screwdriver Rack: 6-Piece1 x Punch Holder

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug Socket62/250H Adjustable Wrench137/250 Grip Pliers143/250 Universal Pliers225/250 Pipe Wrench1987 Sliding T-Bar1990-75 Extension1990-125 Extension 1990-250 Extension 1993Z-94 Ratchet + Coupler1995 Universal Joint8531/300 Tin Snips8601/500 Ball Pein Hammer

55.00

› Ideal for the professional workshop. › Rigid sheetmetal structure with precision CNC punched pegboard. › Three easy-slide drawers incorporating extra strong ball bearing slide mechanisms. › One moveable tray, spanner and screwdriver rack and an assortment of moveable hanging

hooks for maximum �exibility. › Lockable. › Phosphated to prevent corrosion. Blue and grey powder coated. › L=650 x W=250 x H=970. * Picture for illustration purposes only.

Contents/accessories may di�er.

Code No. Accessories 0

661155 1401 - EMPTY with Accessories 30 x Plastic Holders with Pins 1 x Tool Rack: 17-Pin 1 x Screwdriver Rack: 6-Piece 1 x Double Storage Tray 1 x Punch Holder 45.00

126


1401L / 1401L PRO TOOL CABINET / ASSORTMENT159 pieces

d

Code No. Spanners Allen Keys Screwdrivers Tool Cabinet C19 Sockets Accessories 0

662608 1401L PRO - With Accessories and Tools

1B/17M 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

No.2/11M 6x7 8x9 10x11 12x13 14x15 16x17 17x19 18x19 20x22 21x23 24x30

534/9M 10 11 12 13 14 15 16 17 19

42-88M 2 2,5 3 4 5 6 8 10

IN19 5 6 8 10 12 14

42KL-7M 1,5 2 2,5 3 4 5 6

43TX-9M T7 T8 T9 T10 T15 T20 T25 T30 T40

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1401L

Accessories1 x Hook 1 Pin: 10-piece1 x Tool Rack: 17-Pin1 x Double Storage Tray1 x Screwdriver Rack: 10-Piece

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 19-3/4 22 23 24-15/16 26-1. 27-1.1/16 28 30-1.3/16 32-1.1/4

43TV Torx® Gauge Tester403 Hacksaw9534.05 Tape Measure9930.000 Torch1987 Sliding T-Bar1995 Universal Joint1990-75 Extension1990-125 Extension1990-250 Extension1993Z-94 PZK Ratchet & Coupler227/350 Pipe Wrench1993 U-10K Plastic Ratchet36/1 Strap Wrench145/250 Multigrip Pliers62/300 Adjustable Wrench8380-250TL Tower Pincers8516-300 Tin Snips8601-500 Ball Pein Hammer106 Tool Punch Set137/250 Grip Pliers4611 Power Tester8132-200JC Telephone Pliers8316-200JC Side Cutters8250-200JC Combination PliersS8000 Circlip Pliers Set50-20.8 Spark Plug SocketD30 FMZ Socket SetVDE ELS/PH Screwdriver Set

115.40

› Ideal for the professional workshop. › Rigid sheetmetal structure with precision

CNC punched pegboard. › Five easy-slide drawers incorporating

extra strong ball bearing slide mechanisms. › One moveable tray, spanner and screwdriver

rack and an assortment of moveable hanging hooks for maximum �exibility. › Lockable. › Phosphated to prevent corrosion. Blue and grey

powder coated. › L=1300 x W=250 x H=970.

* Picture for illustration purposes only. Contents/accessories may di�er.


662607 1401L - EMPTY with Accessories 1 x Hook 1 Pin: 10-Piece 1 x Double Storage Tray 1 x Tool Rack: 17-Pin 1 x Screwdriver Rack: 10-Piece 90.00

PEGBOARD ACCESSORIES 130 WORKSTATIONS 128

127

1404 / 1404 PRO TOOL CABINET / ASSORTMENT83 pieces

d

Code No. 1B Spanners Allen Keys Screwdrivers Tool Cabinet C19 Sockets Accessories 0

663115 1404 PRO - With Accessories and Tools

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 5 6 8 10 12 14

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1404

Accessories30 x Plastic Holders with Pins1 x Tool Rack: 6-Pin1 x Tool Rack: 17-Pin2 x Large Storage Trays6 x Small Storage Trays1 x Screwdriver Rack

8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug Socket62H/250 Adjustable Wrench137/250 Grip Pliers143/250 Universal Pliers225/250 Pipe Wrench403 Hacksaw1987 Sliding T-Bar1990-75 Extension1990-125 Extension1990-250 Extension 1993Z-94 Ratchet + Coupler1995 Universal Joint9534.05 Tape Measure8132-200 JC Telephone Pliers8250-200 JC Combination Pliers8316-200 JC Side Cutters8531/300 Tin Snips8601/500 Ball Pein Hammer

55.00

› Ideal for the professional workshop. › Rigid sheetmetal structure with precision

CNC punched pegboard. › Three easy-slide drawers incorporating

extra strong ball bearing slide mechanisms. › 80mm-deep doors to accommodate numerous accessories – moveable

shelves, hanging rack and screwdriver rack. › Doors: ZA Registered Design – A2006/01314 & F2006/01315. › Lockable. › Phosphated to prevent corrosion. Blue and grey powder coated. › L=650 x W=345 x H=970.

* Picture for illustration purposes only. Contents/accessories may di�er.


662976 1404 - EMPTY with Accessories 30 x Plastic Holders with Pins 1 x Tool Rack: 17-Pin 1 x Tool Rack: 6-Pin 6 x Small Storage Trays 2 x Large Storage Trays 1 x Screwdriver Rack 47.00

Workstations / Vices / Drawer Units / Tool Panels

1500W / 1500M ARTISAN WORKSTATION

› Ideal for the professional workshop or DIY enthusiast.Galvanised Metal Top

Wooden Top

Code No. Surface L W H 0

663166 1500-12 W Wooden 1200 mm 700 mm 900 mm 34.00663174 1500-15 W Wooden 1500 mm 700 mm 900 mm 43.90663182 1500-20 W Wooden 2000 mm 700 mm 900 mm 53.00663557 1500-12 M Galvanised Metal 1200 mm 700 mm 900 mm 47.80663565 1500-15 M Galvanised Metal 1500 mm 700 mm 900 mm 53.20663573 1500-20 M Galvanised Metal 2000 mm 700 mm 900 mm 59.00

Drawer unit not included

128


MV100 / MV150 MECHANIC

,S VICE

EV150 / EV200 ENGINEERING VICE

› All steel construction. › Cast iron nut on spindle. › Robotic welded construction. › Steel anvil block.

› Heavy duty engineering vice made to SABS 1026:2008 speci�cations. › All steel robot welded construction. › Robust sturdy design which can withstand hammer strikes. › Replaceable spindle and nut, the nut being virtually unbreakable. › Replaceable jaw plates, which are serrated for better grip. › Jaw inserts case hardened to between 540-650 HV (52-57 Rockwell). › Proof load kn (kiloNewton): 150mm-54kN 200mm-90kN. › Tensile strength of handle – 425 MPa – complies with SANS 6892.

Code No.

7400001 MV-100mm Jaw Set Insert7400002 MV-150mm Jaw Set Insert7400100 MV-100mm Spindle & Nut Set7400150 MV-150mm Spindle & Nut Set

MV100 / MV150 SPARES

Code No.

7500001 EV-150mm Jaw Set Insert7500002 EV-200mm Jaw Set Insert7500004 EV-150mm & EV-200mm Spring7500005 EV-150mm & EV-200mm Handle7500006 EV-150mm & EV-200mm Spindle Only7500003 EV-150mm & EV-200mm Nut Only

EV150 / EV200 SPARES

1502 DRAWER UNITS

› Sheetmetal drawer units for 1500 workbenches. › Ideal for the professional workshop or DIY enthusiast. › Rigid sheetmetal pegboard structure. › Numerous accessory options available. › Phosphated to prevent corrosion. › Grey powder coated. › L=570 x W=20 x H=1010mm.

1450S TOOL PANEL

* Tools not included.

SABS System Certification p 8/30/07 10:50 AM Page 2

Composite

C M Y CM MY CY CMY K

Code No. O y 0

6500640 MV-100mm 125 100 7.606500720 MV-150mm 175 150 13.40

Code No. O y 0

3351150G EV-150mm 175 150 25.003350200G EV-200mm 225 200 45.50

Code No. L W H 0

663506 1502 / 2 565 395 365 18.50663522 1502 / 3 565 395 365 19.20

Code No. 0

663123 1450S - Pegboard Only 4.90663352 1450S - With Accessories (Tools Not Included) 5.20

Accessories 1 x PA-H3 Tool Rack: 17-Pin 10 x PA-H1 Hook: 1-Pin

129

Pegboard Accessories › The following accessories are for the 1401, 1401L, 1404 and 1450S

A B C

D E F G

Code No. 664111 PA-H1 Hook: 1-Pin, 10-Piece A664014 PA-H2 Tool Rack: 6-Pin B

664022 PA-H3 Tool Rack: 17-Pin C

664030 PA-T1 Small Storage Tray D

664049 PA-T2 Large Storage Tray E

664057 PA-T3 Double Storage Tray F

Code No. 664065 PA-T4 Screwdriver Rack - Holds 11 Screwdrivers G664138 PA- Starter Pack

Contents

10 x PA-H1 Hook: 1-Pin 1 x PA-H3 Tool Rack: 17-Pin 1 x PA-T4 Screwdriver Rack - Holds 11 Screwdrivers 1 x PA-T3 Double Storage Tray

1425 / 3 TOOL CHEST / ASSORTMENT123 pieces

bd

Code No. Tool Chest 1425/41/1B Foam Insert 1425/41/D19 Foam Insert 1425/27/SP Foam Insert

660967 1425 / 3 Workshop - With Tools

1425 / 3 1B 6-24 Spanners (18)60CP-250 Shifting Spanner

C19 8-32 Sockets (24)No.50/20.8 Spark Plug SKT1987 Sliding T-BarIN19 5-19 Sockets (10)TX19 E10-24 Sockets (8)1990/75mm Extension1990/125mm Extension1990/250mm Extension

ITX19 T20-T50 Sockets (7)No.20 4-13 Sockets (11)2093Z/94 Ratchet + Coupler2090/4 Extension2098 Driving Handle1993-U10T Rev. Ratchet1997/375mm Swivel Handle1995 Universal Joint

2150 8 (Mechanic’s S/D)2150 6.5 (Mechanic’s S/D)2150 4-150 (Electrician’s S/D)2150 6.5-200 (Electrician’s S/D)2160 PH1 (Phillips S/D)2160 PH2 (Phillips S/D)2160 PH3 (Phillips S/D)42/88M Allen Key Set

8132/200 Telephone Pliers8250/200 Combination Pliers8316-200 Side Cutters137/250 Vice Grip145/250 Universal Pliers43TX/09 TORX® Allen Key Set

› Four-compartment sheetmetal tool chest. › Lockable. › Three easy-slide drawers, incorporating full extension ball bearing slide mechanisms. › Drawer latch incorporated into each drawer. › Strong structure, smooth operating hinges. › Retractable spring-loaded handles. › Load capacity per drawer 35kg. › Phosphated and powder coated to prevent corrosion. › High-density foam inserts. › L=687 x W=400 x H=362mm.

Code No. 0

660963 1425 / 3 Tool Chest - EMPTY 35.50

130


Tool Chests / Assortments

1410 ARTISAN‘S TOOL CHEST

› Four-drawer sheetmetal tool chest. › Lockable. › Strong structure, full extension ball bearing slides. › Rubber anti-slip mats in each drawer. › Drawer latch incorporated into each drawer. › Can be stacked on 1510 tool trolley and other 1410 tool chests. › Retractable spring-loaded handles. › Phosphated and powder coated to prevent corrosion. › Load capacity per drawer 35kg. › L=574 x W=417 x H=384mm.

Code No. 0

660817 1410 23.00

1425 / 5 TOOL CHEST / ASSORTMENT149 pieces

bd

Code No. Tool Cabinet 1425/41/1B Foam Insert 1425/41/D19 Foam Insert 1425/27/PL Foam Insert 1425/27/SD Foam Insert 1425/27/HM Foam Insert660969 1425 / 5

Comprehesive - With Tools

1425 / 5 1B 6-24 Spanners (18)60CP-250 Shifting Spanner

C19 8-32 Sockets (24)50/20.8 Spark Plug SKT1987 Sliding T-BarIN19 5-19 Sockets (10)TX19 E10-24 Sockets (8)1990/75mm Extension1990/125mm Extension1990/250mm ExtensionITX19 T20-T50 Sockets (7)No.20 4-13 Sockets (11)2093Z/94 Ratchet + Coupler2090/4 Extension2098 Driving Handle1993-U10T Rev. Ratchet1997/375mm Swivel Handle1995 Universal Joint

8000/A21 Circlip Pliers8000/J21 Circlip Pliers8000/A2 Circlip Pliers8000/J2 Circlip Pliers137/250 Vice Grip145/250 Universal Pliers8132/200 JC Telephone Pliers8250/200 JC Combination Pliers8316-200 JC Side Cutters42/88M Allen Key Set43TX/09 TORX® Allen Key Set

2150 4-150 6.5 6.5-200 82153 5.52160 PH1 PH2 PH32161 PH2No.400 8 x 10 Flare Nut SpannerNo.400 11 x 13 Flare Nut SpannerNo.400 12 x 14 Flare Nut SpannerNo.400 17 x 19 Flare Nut SpannerNo.400 22 x 24 Flare Nut Spanner26R Tubular Box Spanners - 8x9 10x11 12x13 14x1526RS/2 Stepped Tommy Bar

403 Hacksaw9000.00 Digital Vernier702/21M Feeler - Gauge Set9100 Utility Knife9534.05 Tape Measure267/40 Recoil Free-Hammer8601/500g Hammer106 Chisel & Punch Set (6-Piece)95/200 Flat Chisel

› Six-compartment sheetmetal tool chest. › Lockable. › Five easy-slide drawers, incorporating full extension ball bearing slide mechanisms. › Drawer latch incorporated into each drawer. › Strong structure, smooth operating hinges. › Can be stacked on 1525 tool trolley. › Retractable spring-loaded handles. › Load capacity per drawer 35kg. › Phosphated and powder coated to prevent corrosion. › High-density foam inserts. › L=687 x W=400 x H=491mm.

Code No. 0

660965 1425 / 5 Tool Chest - EMPTY 35.50

131

1410

1510

1410

Code No. 1B Spanners Allen Keys Screwdrivers Trolley / Inserts / Tray C19 Sockets Accessories 0

661310 1510 Classic - With Tools

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 5 6 8 10 12 14

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1510 Tool Trolley1281/82-1B62H Insert1280/81-D19/IN19 Insert1280/81-D19 Acc/Skt Insert1282-SD-PH-STB Insert1282-SD-MEC-EL Insert1280/81-PL/137/36 Insert1581 Filler

C19 8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4 7/16AF 9/16AF 7/8AF

36/1 Oil Filter Strap Wrench62/250H Adjustable Wrench143/250 Universal Pliers50/20.8 Spark Plug Socket137/250 Grip Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension1990-250 Extension1993U-10T Rev. Ratchet1995 Universal Joint8000-A2 Circlip Pliers8000-J2 Circlip Pliers8250-200 JC Combination Pliers8132-200 JC Telephone Pliers8316-200 JC Side Cutters

60.00

132


1510 TOOL TROLLEY / ASSORTMENT87 pieces

d

› Ideal for the professional workshop. › Rigid sheetmetal structure. › Five standard and one deep easy-slide drawers incorporating extra strong ball bearing slider mechanisms. › Central drawer locking mechanism. › Two swivel castors (one with safety brake) for maximum mobility and safety. › Handle for easy manoeuvrability. › Load capacity of 300kg. › Load capacity per drawer 35kg. › Blue and grey powder coated. › Drawer latch incorporated into each drawer. › L=651 x W=585 x H=877mm.

Code No. 0

662792 1510 Trolley - EMPTY 48.00

Tool Trolleys / Assortments

1410 + 1510 CONCEPT

1425

15251525

Code No. Tool Trolley 1425/41/1B Foam Insert 1425/41/D19 Foam Insert 1425/27/PL Foam Insert 1425/27/SD Foam Insert 1425/27/HM Foam Insert 0

661325 1525 Comprehesive - With Tools

1525 1B 6-24 Spanners (18)60CP-250 Shifting Spanner

C19 8-32 Sockets (24)No.50/20.8 Spark Plug SKT1987 Sliding T-BarIN19 5-19 Sockets (10)TX19 E10-24 Sockets (8)1990/75mm Extension1990/125mm Extension1990/250mm ExtensionITX19 T20-T50 Sockets (7)No.20 4-13 Sockets (11)2093Z/94 Rev. Ratchet2098 Driving Handle1993-U10T Rev. Ratchet1997/375mm1995 Universal Joint

8000/A21 Circlip Pliers8000/J21 Circlip Pliers8000/A2 Circlip Pliers8000/J2 Circlip Pliers137/250 Vice Grip145/250 Universal Pliers8132/200JC Telephone Pliers8250/200JC Combination Pliers8316-200 JC Side Cutters42/88M Allen Key Set43TX/09 TORX® Allen Key Set

2150 4-150 6.5 6.5-200 82153 5.52160 PH1 PH2 PH32161 PH2400 8 x 10 Flare Nut Spanner400 11 x 13 Flare Nut Spanner400 12 x 14 Flare Nut Spanner400 17 x 19 Flare Nut Spanner400 22 x 24 Flare Nut Spanner26R Tubular Box Spanners - 8x9 10x11 12x13 14x1526RS/2 Stepped Tommy Bar

403 Hacksaw9000.00 Digital VernierNo.702/21M Feeler-Gauge Set9100.00 Utility Knife9534.05 Tape Measure267/40 Recoil Free- Hammer8601/500g Ball Pein-Hammer106 Chisel & Punch- Set (6-Piece)95/200 Flat Chisel

84.40

Code No. 0

662794 1525 Tool Trolley - EMPTY 55.00

133


d

› Ideal for the professional workshop. › Rigid sheetmetal structure. › Five standard and two deep easy-slide drawers incorporating extra strong ball bearing slider mechanisms. › Central drawer locking mechanism. › Two swivel castors (one with safety brake) for maximum mobility and safety. › Handle for easy manoeuvrability. › Load capacity of 300kg. › Load capacity per drawer 35kg. › Blue and grey powder coated. › Drawer latch incorporated into each drawer. › L=758 x W=602 x H=914mm.

1425 + 1525 CONCEPT

Modular Assortments › All assortments are packed in a high-density foam insert that will �t into an appropriate compartment of the 1425 / 3, 1425 / 5 Tool Chest and 1525 Comprehensive Kit.

Code No. 1B Spanners Allen Keys Screwdrivers Trolley / Inserts / Tray C19 Sockets Accessories 0

661306 1581 Classic - With Tools

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

42-88M 2 2,5 3 4 5 6 8 10

IN19 5 6 8 10 12 14

21503-15044-1505.56.5821535.52160PH1PH22161PH2

1581 Tool Trolley1281/82-1B/62H Insert1280/81-D19/IN19 Insert1280/81-D19 Acc/Skt Insert1282-SD-PH-STB Insert1282-SD-MEC-EL Insert1280/81-PL/137/36 Insert1581 Filler Insert

C19 8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4 7/16AF 9/16AF 7/8AF

36/1 Oil Filter Strap Wrench62/250H Adjustable Wrench143/250 Universal Pliers50/20.8 Spark Plug Socket137/250 Grip Pliers1987 Sliding T-Bar1990-75 Extension1990-125 Extension1990-250 Extension1993U-10T Rev. Ratchet1995 Universal Joint8000-A2 Circlip Pliers8000-J2 Circlip Pliers8250-200 JC Combination Pliers8132-200 JC Telephone Pliers8316-200 JC Side Cutters

68.00


d

› Ideal for the professional workshop. › Rigid sheetmetal structure with pegboard back. › Six standard and one deep easy-slide drawers incorporating extra strong ball bearing slider mechanisms. › Working platform with three compartments for small parts. Raised edges. › Central drawer locking mechanism. › Two swivel castors (one with safety brake) for maximum mobility and safety. › Handle for easy manoeuvrability. › Load capacity of 300kg. › Load capacity per drawer 35kg. › Blue and grey powder coated. › Drawer latch incorporated into each drawer. › L=635 x W=495 x H=932mm.

Code No. 0

662801 1581 Trolley - EMPTY 56.00

134


Code No. 0

663023 1425/41/D19 7.82Contents C19 8-32 Sockets (24) 2098 Driving Handle 50/20.8 Spark Plug SKT

1987 Sliding T-Bar 1993-U10T Rev. Ratchet IN19 5-19 Sockets (10)1990/75mm Extension 1997/375mm Swivel Handle TX19 E10-24 Sockets (8)1990/125mm Extension 2090/4 Extension ITX19 T20-50 Sockets (7)1990/250mm Extension 2093Z-94 Ratchet + Coupler No.20 4-13 Sockets (11)1995 Universal Joint 1425/41/D19 Foam Insert

Code No. 0

663024 1425/41/1B 3.21Contents 1B 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24

1425/41/1B Foam Insert 60CP-250 Shifting Spanner

1425 / 41 / D1972 pieces

1425 / 41 / 1B 20 pieces

Code No.

562860 1425 / 41 / D19562865 1425 / 41 / 1B562870 1425 / 27 / PL562875 1425 / 27 / SD562880 1425 / 27 / HM562885 1425 / 27 / SP

1425 / 3 / 5 SPARES

ARTISAN‘S TOOLKITS 218

135

2150 4-150 (Electrician’s) 2160 PH1 (Phillips) 8132/200 Telephone Pliers2150 6.5-200 (Electrician’s) 2160 PH2(Phillips) 8250/200 Combination Pliers2150 6.5 (Mechanic’s) 2160 PH3 (Phillips) 8316-200 JC Side Cutters2150 8 (Mechanic’s) 42/88M Allen Key Set 137/250 Vice Grip145/250 Universal Pliers 1425/27/SP Foam Insert 43TX/09 TORX® Allen Key Set

Code No. 0

663037 1425/27/SP 3.17Contents 8000/A21 Circlip Pliers 137/250 Vice Grip 8250/200JC Combination Pliers

8000/J21 Circlip Pliers 145/250 Universal Pliers 8316-200 JC Side Cutters8000/A2 Circlip Pliers 1425/27/PL Foam Insert 42/88M Allen Key Set8000/J2 Circlip Pliers 8132/200JC Telephone Pliers 43TX/09 TORX® Allen Key Set

Code No. 0

663025 1425/27/PL 3.25Contents

403 Hacksaw 9000.00 Digital Vernier 267/40 Recoil Free Hammer106 Chisel & Punch Set 8601/500g Ball Pein Hammer No.702/21M Feeler Gauge Set9534.05 Tape Measure 9100.00 Utility Knife 95/200 Flat Chisel 1425/27/HM Foam Insert

Code No. 0

663036 1425/27/HM 4.07Contents 2150 4-150 6.5 6.5-200 8 No.400 8 x 10 Flare Nut Spanner

2153 5.5 No.400 11 x 13 Flare Nut Spanner2160 PH1 PH2 PH3 No.400 12 x 14 Flare Nut Spanner2161 PH2 No.400 17 x 19 Flare Nut Spanner26RS-2 Stepped Tommy Bar No.400 22 x 24 Flare Nut Spanner1425/27/SD Foam Insert 26R - 8x9 10x11 12x13 14x15

Code No. 0

663035 1425/27/SD 2.15Contents

› Foam inserts are not covered by the GEDORE guarantee and may be subject to degradation as well as wear and tear. Replacement foam inserts can therefore be purchased separately.

1425 / 27 / SP30 pieces

1425 / 27 / PL 27 pieces

1425 / 27 / HM15 pieces

1425 / 27 / SD 20 pieces

Modular Assortments › Toolbox, Tool Cabinet, Tool Trolley and Modular Assortments.

Code No. / Insert Sockets Accessories 0

662208 REF A-C19/22/ACCInsert1280/81-22-ACC

C19 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug Socket1990-75 Extension1990-125 Extension1990-250 Extension1997/375 Power Bar1987 Sliding T-Bar1995 Universal Joint

2.37


662216 REF B-C19 Insert1280/81-D19

C19 8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4

1993U-10T Rev. Ratchet 2.71

REF A-C19/22/ACC

REF B-C19


663086 REF RF-C19/Z94 C19 8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4

1993 Z-94 Ratchet + Coupler

2.33

REF RF-C19/Z94

Code No. / Insert/Tray 1B Spanners Accessories 0

662224 REF C-1BInsert1280/81-1BMetal Tray1280/81

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

137/250 Grip Pliers145/250 Universal Pliers42/88M Allen Key Set

4.10

REF C-1B

Code No. / Insert/Tray 1B Spanners Accessories 0

663087 REF SF-1B/145Insert1280/81-1BMetal Tray1282

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

137/250 Grip Pliers145/250 Universal Pliers42/88M Allen Key Set

3.96

136


REF SF-1B/145

Code No. / Insert Sockets Allen Key Sockets 0

662232 REF D-C19/IN19Insert1280/81-D19/IN19

C19 8-5/16 10-3/8 11 12 13-1/2 14 15-19/32 16-5/8 17 18-11/16 19-3/4 21-13/16 22 24-15/16 26-1. 27-1.1/16 29-1.1/8 30-1.3/16 32-1.1/4

IN19 5 6 8 10 12 14

2.67

REF D-C19/IN19

11 pieces 29 pieces

21 pieces 29 pieces

21 pieces 26 pieces


662275 REF H-D19/22/ACCInsert1280/81-22-ACC

D19 9 18 20 50/20.8 Spark Plug Socket1987 Sliding T-Bar1990-75 Extension1990-125 Extension1990-250 Extension1995 Universal Joint1997/375 Power Bar

2.36


662283 REF I-D19Insert1280/81-D19

D19 8 10 11 12 13 14 15 16 17 19 21 22 24 26 27 28 29 30 32

1993U-10T Rev. Ratchet 2.36

REF H-D19/22/ACC

REF I-D19

Code No. / Insert Sockets Allen Key Sockets 0

662291 REF J-D19/IN19Insert1280/81-D19/IN19

D19 8 10 11 12 13 14 15 16 17 18 19 21 22 24 26 27 29 30 32

IN19 5 6 8 10 12 14 2.72

REF J-D19/IN19

21 pieces

11 pieces 26 pieces

137

Code No. / Insert 1B Spanners Accessories 0

662240 REF E-1B/62HInsert1281/82-1B/62HMetal Tray1280/81

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

62/250H Adjustable Wrench143/250 Universal Pliers42/88M Allen Key Set

4.12


662259 REF F-D19/ACC/SKT Insert1280/81-D19 ACC/SKT

D19 7/16AF 9/16AF 7/8AF

50/20.8 Spark Plug SKT1987 Sliding T-Bar1990-75 Extension1990-125 Extension1990-250 Extension1995 Universal Joint1993U-10T Rev. Ratchet

2.18

REF E-1B/62H

REF F-D19/ACC/SKT


662267 REF G-C32/6Insert1280/81-D32/6

C32 1.3/8AF 36-1.7/16 38-1.1/2 41-1.5/8 46-1.13/16 50-2.

3287/447 Sliding T-Bar3290-200 Extension3290-400 Extension3293U-1/440 Rev. Ratchet

8.70

REF G-C32/6

29 pieces 11 pieces

11 pieces

Code No. / Insert Pliers/Circlip Pliers Accessories 0

662356 REF L-PL/137/36 Insert1280/81-PL137/36

Pliers8132/200 JC Telephone Pliers8250/200 JC Universal Pliers8316/200 JC Side CuttersCirclip Pliers8000-A28000-J2

36/1 Strap Wrench137/250 Grip Pliers

2.39

REF L-PL/137/36

Code No. / Insert Pliers 0

662941663082

REF M-PL/81/82/83 Ass.REF MF-PL/81/82/83 Ass.Insert1282-Pliers

8132/200 JC Telephone Pliers8250/200 JC Universal Pliers8316/200 JC Side Cutters

2.702.01

REF M/MF-PL/81/82/83


662321 REF K-D32/6Insert1280/81-D32/6

D32 1.3/8AF 36 38 41 46 50

3287/447 Sliding T-Bar3290-200 Extension3290-400 Extension3293U-1/440 Rev. Ratchet

8.71

REF K-D32/6 REF-10SD

Code Description 2150 2153 2160 2161 0

662348 10SD 4 5.5 6.5 83-150 4-150

5.5 PH1 PH2 PH2 1.83

REF N-10

Code Insert 2150 2153 2160 2161 0

662968 1282-2161 ELS+PH 1282-2150 MEC

4 5.5 6.5 83-150 4-150

5.5 PH1 PH2 PH2 2.10

11 pieces 10 pieces

8 pieces 12 pieces

4 pieces 6 pieces

138


REF WF/VF

Code Inserts 2150 2160 2161 2153 0

663092663091

REF WF-2153REF VF-2161

4 5.5 6.5 8 5.53-150 4-150 PH1 PH2 PH2

0.580.45

7 pieces 5 pieces

5 pieces

5 pieces5 pieces

7 pieces

139

REF OF

Code No. / Insert Accessories 0

663020 REF P-4 Ext – T-bar AssInsert1282 EXT

1990-75 Extension1990-125 Extension1990-250 Extension1987 Sliding T-Bar

1.10

REF P-4 EXT T-BAR

REF 0-6SD

REF Q-4

REF QF-4

Code No. 2150 2160 0

663018 REFO-6SDInsert1282-6SD 3C

45.56.58

PH1PH2

1.78

Code No. 2150 2160 0

663083 REF OF-6SD InsertREF OA-2150-6SD Foam Insert

45.56.58

PH1PH2

0.73


663084 REF PF-4 Ext – T-bar AssInsertFoam

1990-75 Extension1990-125 Extension1990-250 Extension1987 Sliding T-Bar

1.08

REF PF-4 EXT T-BAR


663022 REF Q-4 ACC – Power Bar Ass.Insert1282-4 ACC.

1990-75 Extension1990-250 Extension1995 Universal Joint1997-375 Swivel Handle

1.30


663085 REF QF-4 ACC – Power Bar Ass.InsertFoam

1990-75 Extension1990-250 Extension1995 Universal Joint1997-375 Swivel Handle

1.30

HAMMERS / STRIKING TOOLS

140

HAMMERS, CHISELS, PUNCHES

SETS

RECOIL FREE HAMMERS

142

CHISELS

142

PUNCH SETS

143

BALL PEIN HAMMERS

142

CENTRE PUNCHES

142

PUNCH NUMBER/LETTER SET

143

HAND GUARD

142

CHISEL & PUNCH SET

143

SLEDGE HAMMERS

144

› Splinter-proof, shatter-proof and wear resistent polymide heads. › Powder coated with silver hammer-e�ect enamel. › Robust and durable steel tube handle.

› Drop forged. › Striking faces induction hardened

and precision ground › Blue epoxy powder coated. › In accordance with SANS 387. › Hardwood handles.

› Made from Chrome Molybdenum Vanadium air hardened 45CrMoV7 steel, in accordance with DIN 6453. › Carefully hardened and tempered

along the full length. › Striking head induction tempered to

prevent shattering. › Working edge polished and clear varnished, free of burrs.

› Made from Chrome Molybdenum Vanadium air hardened 45CrMoV7 steel, in accordance with DIN 6451. › Carefully hardened and tempered along the

full length. › Striking head induction tempered to prevent shattering. › Working edge polished and clear varnished, free of burrs.

NEW

142


* With Guard

Hammers / Striking Tools

248 ST RECOIL-FREE HAMMERS

95 FLAT COLD CHISELS

96 CROSS-CUT CHISELS

8601 BALL PEIN HAMMERS

Code No. y 0

8828950 248 ST 30mm 295 0.6008829170 248 ST 40mm 305 0.8008829250 248 ST 50mm 315 1.0058829330 248 ST 60mm 340 1.8008830260 E 248 / 30 Replacement Head (1 Piece) 0.0158830420 E 248 / 40 Replacement Head (1 Piece) 0.0318830500 E 248 / 50 Replacement Head (1 Piece) 0.0508830690 E 248 / 60 Replacement Head (1 Piece) 0.090

Code No. y 0

676381 8601 / 100 280 0.160676403 8601 / 200 310 0.320676411 8601 / 300 325 0.420676438 8601 / 500 370 0.610676446 8601 / 700 375 0.840676519 8601 / 900 400 1.140676527 8601 / 1100 410 1.240

Code No. Tip y 0

8698640 95 - 125 15mm 125 0.1258698720 95 - 150 18mm 150 0.2258698800 95 - 175 21mm 175 0.2708698990 95 - 200 24mm 200 0.2708699100 95 - 250 28mm 250 0.4808699370 95 - 300 30mm 300 0.7008699960 95 HS-250 with guard 28mm 250 0.7208700640 95 HS-300 with guard 30mm 300 0.860

Code No. y 0

8702180 96 - 125 125 0.1408702260 96 - 150 150 0.2208702340 96 - 175 175 0.2708702420 96 - 200 200 0.3808702500 96 - 250 250 0.5358702770 96 - HS-250 with guard 250 0.695

› Made from PVC. › Ergonomic design. › Rectangular shape ensures no rolling away. › Optimum hold – avoids hand fatigue and injuries. › For use with 95, 2095 and 2096 chisels.

› Made from Chrome Molybdenum Vanadium air hardened 45CrMoV7 steel, in accordance with DIN 7250. › Hardened and tempered along the full length. › Striking head induction tempered to prevent

shattering. › Working edge polished and clear varnished.

108 UNI HAND GUARD

100 CENTRE PUNCHS

Code No. 0

8658500 108 UNI 160

Code No. Tip y 0

8721050 100 - 10 4mm 120 608721130 100 - 12 5mm 120 958721210 100 - 15 5mm 150 1208721480 100 - 16 8mm 150 240

› 6mm print height. 9 numbers. › To label �nished parts such as signs, tools etc. › In blue plastic box. › Made from hardened steel, with hardened handle and

tempered striking head to prevent shattering.

› 6mm print height. 27 letters. › To label �nished parts such as signs, tools etc. › In blue plastic box. › Made from hardened steel, with hardened handle and

tempered striking head to prevent shattering.

143

2201 LETTER SET

99 DRIFT PUNCHS

2200 NUMBER SET

› Made from Chrome Molybdenum Vanadium air hardened 45CrMoV7 steel, in accordance with DIN 6458. › Hardened and tempered along the full length. › Striking head induction tempered to prevent

shattering. › Working edge polished and clear varnished.

Code No. y 0

8708700 99 10-1 120 608708970 99 10-2 120 608709190 99 10-3 120 608711170 99 12-4 120 908711330 99 12-5 120 908711410 99 12-6 120 908711680 99 12-7 120 1008711760 99 12-8 120 105

Code No. 0

8605140 2200 - 6 0.300

Code No. 0

8605220 2201 - 6 1.30

› Made from Chrome Molybdenum Vanadium air hardened 45CrMoV7 steel. › Hardened and tempered along the full length. › Striking head induction tempered to prevent

shattering. › Working edge polished and clear varnished. › Comes in a PVC stand.

Code No. Contents 0

8725200 10697 - 125 97 - 150 98 - 125 99 - 12-3 100 - 10 119 - 4

0.550



113 DRIFT PUNCH SET6 pieces

116 PIN PUNCH SET6 pieces

106 CHISEL & PUNCH SET6 pieces



Code No. Contents 0

8753680 11399 - 10-1 99 - 10-2 99 - 10-3 99 - 12-4 99 - 12-5 100 - 10

0.450

Code No. Contents 0

8757670 116 A119 - 3 119 - 4 119 - 5 119 - 6 119 - 7 119 -8

0.510

SLEDGE HAMMERDeveloped in 1975 to withstand the rigorous hard rock mining conditions with hard hitting power that delivers more than 36 000 strikes smoothly and efficiently.

640S 622C 620C

Forged head Superior grain structure.Striking faces hardened to 50-58HRC.

Positive locking plate Head will not seperate from the handle.

Thickened boss Further protects the hammer fromoverstrikes.

Non-slip grip Secure grip in both wet and dry conditions.

Hich tensile steel rodsHigh strength rubber-to-metal bonding makes the handle extremely strong.

Ergonomic shape Handle is shaped to provide a comfortable and safe grip.

Impact absorbing handle Heavy duty rubber cushions impact, redusing fatigue and injury.

Locked-in lanyard hole Totally safe attachment.

144


Sledge / Club Hammers

620C CLUB HAMMERS

640S SLEDGE HAMMERS

› Handle consists of a core that contains high tensile steel rods moulded in abrasive-resistent rubber ensuring outstanding durability. › Superior quality rubber handle provides excellent grip in wet and dry conditions

allowing for versatility and safety. › Head 99.98% copper reduces damage to workpieces and reduces chance of sparking

in hazardous areas.

Applications: Mining, Petrochemical, Engineering, Toolmaking

622C COPPER SLEDGE HAMMERS

› Handle consists of a core that contains high tensile steel rods moulded in abrasive-resistent rubber ensuring outstanding durability. › Locking plate design ensures head will not seperate from the handle. › The abrasive-resistent rubber is injected all the way into the eye of the hammer head. › Superior quality rubber handle provides excellent grip in wet and dry conditions

allowing for versatility and safety. › Hammer head hardened to 50-58HRC and confroms to ANSI, BS876 & ISO15601 Speci�cations.

Applications: Mining, Building & Construction, Demolition, Heavy Industry, Military, Emergency Serrvices.

› Handle consists of a core that contains high tensile steel rods moulded in abrasive-resistent rubber ensuring outstanding durability. › Locking plate design ensures head will not seperate from the handle. › The abrasive-resistent rubber is injected all the way into the eye of the hammer head. › Superior quality rubber handle provides excellent grip in wet and dry conditions

allowing for versatility and safety. › Hammer head hardened to 50-58HRC and confroms to ANSI, BS876 & ISO15601 Speci�cations.

Applications: Mining, Construction, Steelwork, Fencing, Electrical Engineering, Chiseling and Chasing, Surveying

NEW

NEW

NEW

145

Code No. y 0

676530 620C Club Hammer 250 1.10676531 620C Club Hammer 250 1.80

Code No. y 0

676532 640S Steel Sledge Hammer 535 3.60676533 640S Steel Sledge Hammer 710 6.30

Code No. y 0

676534 622C Copper Sledge Hammer 250 1.80676536 622C Copper Sledge Hammer 535 3.60676538 622C Copper Sledge Hammer 710 6.30

INSULATED SAFETY TOOLS

146

VDE INSULATED

SAFETY TOOLS

SPANNERS

148

TORQUE WRENCH

149

CABLE SHEARS

152

NUT DRIVERS

148

SCREWDRIVERS

149

VOLTAGE TESTER

152

ADJUSTABLE WRENCH

149

PLIERS / SIDE CUTTERS

150

TOOLSETS

153

VDE 2 E 19

VDE 2 E 13

VDE 894 12

VDE 894 22

VDE 2 E VDE SINGLE ENDED RING SPANNERSdeep offset

› Gedore Vanadium steel 31CrV3. › VDE insulation up to 1000 V, according to EN 60900/IEC 60900, two-ply Check-Tool insulation.

VDE 894 VDE SINGLE OPEN ENDED SPANNERS

› Gedore Vanadium steel 31CrV3. › VDE insulation up to 1000 V, according to EN 60900/IEC 60900, two-ply Check-Tool insulation. › Jaw set at 15 °.

iO ö 1000 V VDE 2133

NUT DRIVERSwith 3C handle

› 3-component handles Power-Grip3 with hanging hole. › Ergonomic handle design. › Head depth 25mm, blade length 125mm. › VDE insulation up to 1000 V, according to EN 60900/IEC 60900.

Code No. Contents 0

1747260 VDE 2133 / 102133 5,0 6,0 7,0 8,0 9,0 10,0 11,0 12,0 13,0 14,0

1.30

VDE 2133 NUT DRIVER SET10 pieces

› Only tools bearing these test symbols are classed as insulated tools.

› VDE insulation as per standard EN60900, IEC/CEI900, VDE0680.

› Safe working in high-voltage areas.

› Up to 1000V alternating current.

› Up to 1500V direct current.

iO ö 1000 V

148


Code No. y 3 0

6036000 VDE 2 E10mm 170 10 0.0976036190 VDE 2 E11mm 180 11 0.0936036350 VDE 2 E13mm 190 13 0.1306036430 VDE 2 E14mm 210 14 0.1516036780 VDE 2 E17mm 220 17 0.1996036860 VDE 2 E19mm 240 19 0.2446037320 VDE 2 E32mm 330 32 0.683

Code No. y 3 0

6572120 VDE 894 10mm 105 10 0.0346572200 VDE 894 11mm 115 11 0.0446572470 VDE 894 13mm 135 13 0.0676572550 VDE 894 14mm 145 14 0.0816572980 VDE 894 17mm 160 17 0.1176573010 VDE 894 19mm 175 19 0.1616574920 VDE 894 32mm 280 32 0.558

Code No. N 1 Head Ø 0

1747045 VDE 2133 3 225 3 9 0.1091747053 VDE 2133 4 225 4 10 0.1111747061 VDE 2133 5 225 5 11 0.1121747088 VDE 2133 6 225 6 12 0.1141747096 VDE 2133 7 235 7 14 0.1521747118 VDE 2133 8 235 8 15 0.1541747126 VDE 2133 9 235 9 16 0.1541747134 VDE 2133 10 245 10 17 0.1611747142 VDE 2133 11 245 11 19 0.1931747150 VDE 2133 12 245 12 20 0.1961747169 VDE 2133 13 245 13 21 0.1991747177 VDE 2133 14 245 14 22 0.1981747185 VDE 2133 17 245 17 26 0.222

V 62 ADJUSTABLE WRENCH

› Chrome Vanadium steel 31CrV3. › Swedish pattern. Jaw set at 15o. › Blackened �nish. Ground head. › Moulded PVC handle. › Insulated up to 1000V. › Protective guard. › Due to the adjsuting knurl not being insulated, › this tool is not certi�ed to VDE.

ö 1000 V VDE 4507 TORQUE WRENCH 1/2"5-50 N·m / 4-37 lbf·ft

› Controlled screw tightening in the most common range of 5 - 50Nm / 4 - 37 lbf·ft. › Automatic short-path actuation with tactile impulse and audible signal. › Dual scale with a scale graduation of 5Nm and 5lbf·ft. › Fine toothed ratchet with square drive as per DIN 3120 - A 12.5, ISO 1174. › VDE insulation up to 1000V, according to EN 60900/IEC 60900, two-ply

Check-Tool insulation.

VDE 2160 PH PHILLIPS SCREWDRIVERSfor cross-head screws PH

VDE 2170 ELECTRICIAN‘S SCREWDRIVERSfor slotted head screws

Code No. + ; N 0

1612115 VDE 2160 PH1 M2 - M3 1 180 0.0821612123 VDE 2160 PH2 M3,5 - M5 2 210 0.1191612131 VDE 2160 PH3 M5,5 - M7 3 270 0.188

iO ö 1000 V

› Individually tested, VDE insulation up to 1000 V, acc. to EN 60900/IEC 60900, fully insulated blade › Tip to DIN ISO 2380-1 form B › 3-component handles Power-Grip3 with hanging hole › Ergonomic handle design enables precise and fatigue-free working › Positive-�t joint of handle and blade for optimum transmission of force › Type of drive marked at end of the handle › Blade from GEDORE molybdenum-vanadium-Plus tempered steel

iO ö 1000 V

› Individually tested, VDE insulation up to 1000 V, acc. to EN 60900/IEC 60900, fully insulated blade › Blade tip to DIN ISO 8764-1 PH › 3-component handles Power-Grip3 with hanging hole › Ergonomic handle design enables precise and fatigue-free working › Positive-�t joint of handle and blade for optimum transmission of force › Type of drive marked at end of the handle › Blade from GEDORE molybdenum-vanadium-Plus tempered steel

Code No. ? K N 0

1612220 VDE 2170 2,5 2.5 160 0.0381612247 VDE 2170 3,5 3.5 185 0.0551612255 VDE 2170 4 4.0 185 0.0581612271 VDE 2170 5,5 5.5 225 0.0951612298 VDE 2170 6,5 6.5 260 0.134

VDE 2160-2170 SCREWDRIVER SET6 pieces

Code No. Contents 0

1616048 VDE 2170-2160 PH 06 ? VDE 2170 3.5 4 5.5 6.5 660; VDE 2160 PH1 PH2

149

Code No. y O 0

636854 V 62 / 200H* 200 25 0.250636858 V 62 / 250H 250 30 0.460636862 V 62 / 300H 300 36 0.700


6681920 VDE 4507-4 1/2 12.5 370 1.251

P iO ö 1000 V

VDE 8316 H VDE POWER SIDE CUTTERSwith VDE insulating sleeves

› For hard wires. › Oil hardened, chrome plated. › Cutting edges inductively rehardened, approximately 64HRC. › Handles with VDE dipped insulation as per DIN EN 60900.

P iO ö 1000 V

VDE 8314 H VDE SIDE CUTTERSwith VDE insulating sleeves

› With slender head - ideal for con�ned spaces. › For medium-hard wire, 1.6 mm. › Cutting edges inductively rehardened, approximately 64HRC. › Oil hardened, chrome plated. › GEDORE special hardened and tempered steel, chrome plated. › Handles with VDE dipped insulation as per DIN EN 60900.

iO ö 1000 V VDE 8098 H

VDE STRIPPING PLIERSwith VDE insulating sleeves

› Opening stop, spring and brass adjusting screw. › For cables 0.8 - 6.0 mm2. › GEDORE special hardened and tempered steel, chrome-plated. › Handles with VDE insulation as per DIN EN 60900.

Code No. Ø y 0

1552155 VDE 8314-140 H 1.6 140 0.1771552163 VDE 8314-160 H 1.6 160 0.231

150


R iO ö 1000 V

VDE 8250 H VDE HEAVY DUTY COMBINATION PLIERSwith VDE insulating sleeves

› For consistent use under tough working conditions. › To cut all wire types including piano wire. › Good lever action for easy cutting. › In heat treated steel as per DIN EN 10083. › Oil hardened, chrome plated. › Cutting edges inductively rehardened, approximately 64HRC. › Handles with VDE dipped insulation as per DIN EN 60900.

Code No. y 0

1550942 VDE 8250-160 H 160 0.2281550950 VDE 8250-180 H 180 0.2881550969 VDE 8250-200 H 200 0.369

Code No. y 0

1551000 VDE 8316 - 200 H 200 0.350

Code No. y 0

1552074 VDE 8098-160 H 160 0.204

R iO ö 1000 V

VDE 8120 H VDE FLAT NOSE PLIERSwith VDE insulating sleeves

› Long, �at jaws and serrated gripping surfaces. › GEDORE special hardened and tempered steel, chrome plated. › Handles with VDE insulation as per DIN EN 60900.

S iO ö 1000 V

VDE 8122 H VDE ROUND NOSE PLIERSwith VDE insulating sleeves

› Long, round jaws and serrated gripping surfaces. › GEDORE special hardened and tempered steel, chrome plated. › Handles with VDE insulation as per DIN EN 60900.

VDE 8132 AB H VDE BENT NOSE TELEPHONE PLIERSwith VDE insulating sleeves, angled pattern

› Long, �at jaws and angled gripping surfaces. › Face hardness approximately 62HRC. › GEDORE special hardened and tempered steel, chrome plated. › Handles with VDE insulation as per DIN EN 60900.

Code No. y 0

1552104 VDE 8122 -160 H 160 0.180

iO ö 1000 V VDE 8099 H

VDE STRIPPING PLIERSwith VDE insulating sleeves

› Self adjusting for wires 0,5-5,0mm2. › GEDORE special hardened and tempered steel, chrome plated. › Handles with VDE insulation as per DIN EN 60900.

Code No. y 0

1552090 VDE 8120 - 160 H 160 0.210

Code No. y 0

1552139 VDE 8132AB-160 H 160 0.1501552147 VDE 8132AB-200 H 200 0.210

T iO ö 1000 V

151

Code No. y 0

1552082 VDE 8099-160 H 160 0.170

152


iO ö 1000 V VDE 4522

CABLE KNIFE

› Strong, straight blade made from hardened and tempered steel. › Tough, resilient plastic handle. › With VDE insulation as per DIN EN 60900.

ö 1000 V V 180 CABLE SHEARS

› Cuts cable up to 27mm, solid material up to 200 mm2. › Individually tested, insulation up to 1000V.

ö 1000 V V 4614 PLUS

VOLTAGE TESTER 1000 Vtwo-pole with LED display

Code No. y 0

6430330 180-23 620 2.12

T iO ö 1000 V

VDE 8132 H VDE TELEPHONE PLIERSwith VDE insulating sleeves, straight pattern

› Long, �at jaws and straight gripping surfaces. › Face hardness approximately 62HRC. › GEDORE special hardened and tempered steel, chrome plated. › Handles with VDE insulation as per DIN EN 60900.

Code No. y 0

1552112 VDE 8132 - 160 H 160 0.1501552120 VDE 8132 - 200 H 200 0.210

Code No. y 0

6690400 VDE 4522 180 0.104

Code No. 0

2241137 V 4614 0.270

› AC and DC voltages from 12-690V. › Accoustic continuity testing up to 500KOhm. › Single pole phase testing > 100VAC. › With VDE insulation as per DIN EN 60900. › Twin-pole with LED display. › 2x batteries type AAA. › Integrated LED torch (white). › Automatic on/o� function. › Protection classi�cation IP65, dust-proof, hose-proof. › Safety outlet and CEE one-hand operation. › Displays polarity in case of direct current (DC).

ELECTRICIAN‘S TOOLSET 37 pieces

1100-1094VDE TOOL ASSORTMENT HYBRID 53 pieces

n c

iO ö 1000 V

153

o d ? 5

iO ö 1000 V

VDE 1001 VDE TOOLSET14 pieces

› With practical foam insert in sturdy PVC case. › Dimensions: 395 x 295 x 106mm. › Cranked allen socket screwdriver no. 42 is for locking

the adjusting screw of extension no. VDE 1990, not VDE insulated.

o d 5

iO ö 1000 V

› Double stitched and bound. › Very durable water repellent inner lining. › Heavy duty zip. › Reinforced inners.

VDE 1101-003 VDE TOOLSET8 pieces in i-BOXX® 72

› In Gedore i-BOXX® 72, with transparent cover for easy view of tools. › Dimensions: 367 x 316 x 72mm.

Code No. Contents 0

1828045 1101-003 VDE 8132-200H VDE 2170 4 5,5 VDE 8250-180H VDE 2160 PH1 PH2 VDE 8314-160H VDE 4615 3

2.00

T P

? ;

iO ö 1000 V

› Perfect range of tools for all vehicle types. › Comes in Gedore L-BOXX´®

NEW

Code No. Allen Keys Sockets Accessories 0

6602560 1001 VDE Toolset

42 2,5 VDE 19 10 12 13 14 17 19 22 24

VDE 1993 UVDE 1990-5 -10VDE 1989 TVDE 2170 5,5

3.40

VDE Nut Drivers Accessories 0

2133 4 6 8 10 13

Electrician’s ToolcaseVDE 8098-160H Stripping PliersVDE 8250-200H Combination PliersVDE 8314-160H Side CuttersVDE 8132-200H Telephone Pliers137-175 Grip PliersV62-250 Shifting Spanner

145-250 Waterpump Pliers9930.000 Torch9534.05 Tape MeasureVDE 4522 Cable KnifeDigital Multimeter8601-300 Ball Pein Hammer

6.10

Code No. 1B Spanners 42-88M Allen Keys VDE Screwdrivers668122 Electrician’s

Tool Set8 10 13 17 19 2 2,5 3 4 5 6

8 10160PHS1x802x1003x150170ELS0.5x3x1000.8x4x1001.2x6.5x150

Code No. Contents 02979063 1100-1094 VDE 30 6 8 9 10 11 12 13 14

15 16 17 18 19 20 22VDE INX 30 8 10 12VDE 3090-3 3093-6VDE 3093-UVDE 2170 2,5 3,5 4 5,5VDE 2160 PH1 2 3VDE 2163 TX T20 T25 T30VDE 8094

VDE 146 10VDE 8250-200HVDE 8314-180HVDE 8132 AB-200HVDE 8120-160HVDE 4522V914 1 2 3

8.04

iOö

No. 1B Spanners

NEW

TORQUE TOOLS

154

TORQUE TOOLS

TORCOFIX

158

TORQUE SLIPPERS

168

CALIBRATION ANALYSERS

175

DREMASTER

160

TORQUE BREAKERS

170

FITTINGS / RATCHET HEADS

178

DREMOMETER

162

TORQUE SCREWDRIVERS

174

MULTIPLIERS

180

1

1

1

1

1

1

1

1

3

3

2

3

OVERVIEW OF GEDORE

TORQUE TOOLS

Page Series/Type Precision +/- Drive Ratchet ScaleOperation length independent

Release types

0,4 – 3.000Nm Mechanical Torque Wrenches Mechanical torque wrench

163 Dremometer Mini 3% b

160 Dremometer 3% b g

157 Dremaster DMK 3% d e

157 Dremometer DMSE 3% } ~

155 Torcofix K 3% b e

155 Torcofix SE 3% } ~

155 Torcofix FS 3% } ~

164 TSN Slipper 4% b d 3

167 TBN Breaker 4%, 6% j }165 TSP Slipper 6% b

165 TSC Slipper 6% b

169 Typ 83 4% b d168 Typ 88 4% e

0,04 – 13,6Nm Torque screwdriver

170 TLS Pro 6% i

170 Typ 756 S 6% i

2 – 1.000Nm Electronic torque wrench

168 Torcotronic III 1% d

Torque testers

171 Dremotest E 1% b f

TORCOFIX 158 DREMASTER 160

156

TORQUE TOOLS

Different Torque Tool Mechanisms Range N·m

When the preset torque value is reached the operator will hear a click, feel an impulse and there will be approximately 3° of tool movement. Resetting takes place when the hand pressure is released. Work can then immediately continue.These tools are generally length dependent (exception DREMOMETER models AM - F), thus the position of the hand on the tool alters the torque produced. Continued application of force after the 3° of movement will cause the torque applied to increase above the required preset limit.

When the preset torque value is reached, these tools break at a speci�c point along the tool’s length - usually at a pivot point near the tool’s head. In most cases the movement is approximately 20°. The tool is automatically reset by allowing the handle to return to its in line position. These tools are length dependent, thus the position of the hand on the tool alters the torque produced. Continued application of force after 20° of tool movement will increase the torque applied above the preset limit but with the greater angle of tool movement this is less likely.

When the preset torque value is reached, a mechanism in the tool causes the application of torque to cease and the tool slips free for a short time until resetting occurs. Even if the application of force is repeated, the preset torque value will not be exceeded, therefore making it impossible to overtighten a fastener. These tools are not length dependent.

Click ToolsOvertightening Possible

Breaking ToolsOvertightening Unlikely

Slipping ToolsOvertightening Impossible

Torque

50 10 15 20 40 60 80 100 150 200 300 400 500 750 1000 1500 2000

Torque

Torque

approx. 3° m

ovement

approx. 20° movement

Preset Torque Value

Preset Torque Value

Preset Torque Value

Applied Force

Applied Force

Applied Force

1

2

3

Overtightening Possible

Overtightening Unlikely

Overtightening Impossible

2,5 – 12Nm

6 – 3.000Nm

20 – 850Nm

20 – 400Nm

1 – 750Nm

5 – 50Nm

2 – 200Nm

3 – 125Nm

5 – 200Nm

1 – 10Nm

0.8 – 2000Nm

100 – 1500Nm

5 – 125Nm

0,05 – 25Nm

0,05 – 9Nm

1 – 10Nm

70 – 350Nm

1 – 10Nm

0,9 – 3150Nm

Page Series/Type Precision +/- Drive Ratchet ScaleOperation length independent

Release types

0,4 – 3.000Nm Mechanical Torque Wrenches Mechanical torque wrench

163 Dremometer Mini 3% b

160 Dremometer 3% b g

157 Dremaster DMK 3% d e

157 Dremometer DMSE 3% } ~

155 Torcofix K 3% b e

155 Torcofix SE 3% } ~

155 Torcofix FS 3% } ~

164 TSN Slipper 4% b d 3

167 TBN Breaker 4%, 6% j }165 TSP Slipper 6% b

165 TSC Slipper 6% b

169 Typ 83 4% b d168 Typ 88 4% e

0,04 – 13,6Nm Torque screwdriver

170 TLS Pro 6% i

170 Typ 756 S 6% i

2 – 1.000Nm Electronic torque wrench

168 Torcotronic III 1% d

Torque testers

171 Dremotest E 1% b f

DREMOMETER 162

157

K b - e 1 - 750Nm FS }~ 2 - 200Nm

SE FS K

SE } 5 - 50Nm

TORCOFIXRobust torque wrench with square drive and integrated ratchet-head function for controlled bi-directional tightening.

Scale Easily readable double scale (Nm/lbf.ft), well protected behind a window with a magnifying glass effect. The torque setting is readable on the scale or, more particularly, on the scale in combination with the scale ring.

Micrometre scale Optimised shape, stable scale frame with red-shaded micrometer scale ring. Model-dependent intervals of 0.025, 0.1, 0.25, 0.5 or 1Nm allow very accurate settings.

Ligthweight and reliable Locking button enables reliable locking of the torque setting.

Handgrip with a user aid Black plastic handgrip, new ergonomically enhanced shape, with an indentation in the middle of the handgrip. User aid and reference points for calibration.

Automatic actuation The TORCOFIX actuates with a clear tactile impulse and audible signal and is immediately ready for operation again.

Robust steel tube With high corrosion protection, copper clad and chrome plated, silk-matt.

Chrome-plated ratchet head All 1/4“-1/2“ square drives of the TORCOFIX K series have a black plastic cap – also referredto as a mushroom head. This mushroom head prevents an unintentional pulling out of the whole square drive when changing the nut socket.

Classi�ed to DIN EN ISO 6789:2003 Type II Class A, with a factory certi�cate allowing for operations to be traced back. Calibrated to a permitted +/- 3% deviation and better. The speci�cations of the standard (+/- 4%) are exceeded.

Maximum +/- 3% tolerance:Guaranteed TORCOFIX accuracy of +/- 3% of relevant scale value reading for each 5,000 tightening cycles. Includes test certificate as per DIN EN ISO 6789. Serial number on the wrench and on the certificate allows clear product identification, traceable to national norms.

158

TORQUE TOOLS

4550 TORQUE WRENCH TORCOFIX K40-750Nm / 30-550lbf·ft

4549 TORQUE WRENCH TORCOFIX K1-50Nm / 0.75-37lbf·ft

4150-4151 TORQUE WRENCH TORCOFIX FS2-200Nm

4101 TORQUE WRENCH TORCOFIX SE5-50Nm / 3.5-37lbf·ft

Use: › For use in almost all industrial manufacturing areas. › For controlled nut and bolt tightening.

Features: › Adjustable torque wrench with a square drive and integrated ratchet head function. › For controlled bi-directional tightening. › Interchangeable mushroom head square drive with ball-locking mechanism as per DIN 3120. › In accordance with DIN EN ISO 6789, traceable to national norms. › Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Lever breaking mechanism with a castor guarantee tactile impulse and audible actuation signals. › Double scale Nm and lbf.ft behind window with magnifying e�ect. › Black plastic handgrip with slip-resistant ribbed surface. › Full-metal construction from high strength aluminium alloy. › Additional micrometer scale with a Nm graduation of 0.1, 0.25, 0.5 or 1Nm. › Supplied with a calibration certi�cate. › Unique serial number for traceability.


Features: › Adjustable torque wrench with a square drive and integrated ratchet head function. › For controlled bi-directional tightening. › Interchangeable mushroom head square drive with ball-locking mechanism as per DIN 3120. › In accordance with DIN EN ISO 6789, traceable to national norms. › Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Lever breaking mechanism with a castor guarantee tactile impulse and audible actuation signals. › Double scale Nm and lbf.ft behind window with magnifying e�ect. › Black plastic handgrip with slip-resistant ribbed surface. › Sturdy, varnished tubular steel construction, with zinc plated ratchet head and top grade plastic parts. › Additional micrometer scale with a Nm graduation of 0.1, 0.25, 0.5 or 1Nm. › Supplied with a calibration certi�cate. › Unique serial number for traceability.

9x12 9x12

14x18Use: › For use in almost all industrial manufacturing areas. › For controlled nut and bolt tightening.

Features: › Adjustable torque wrench with a 9x12 or 14x18 rectangular cavity. › For controlled bi-directional tightening. › With pin-locking mechanism for replaceable 9x12 or 14x18 spanner end �ttings. › In accordance with DIN EN ISO 6789, traceable to national norms. › Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Lever breaking mechanism with a castor guarantee tactile impulse and audible actuation signals. › Double scale Nm and lbf.ft behind window with magnifying e�ect. › Full-metal construction from high strength aluminium alloy. › Supplied with a calibration certi�cate. › Unique serial number for traceability.


Features: › Adjustable torque wrench with a 9x12 rectangular cavity. › For controlled bi-directional tightening. › With pin-locking mechanism for replaceable 9x12 spanner end �ttings. › In accordance with DIN EN ISO 6789, traceable to national norms. › Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Lever breaking mechanism with a castor guarantee tactile impulse and audible actuation signals. › Double scale Nm and lbf.ft behind window with magnifying e�ect. › Full-metal construction from high strength aluminium alloy. › Supplied with a calibration certi�cate. › Unique serial number for traceability.

TORCOFIX K / SE / FS

159

Code No. a „

a Nm lbf·in y 0

2201429 4549-00 1/4 6.3 1-5 0,75-3,7 225 0.3231545132 4549-02 1/4 6.3 2-25 1,5-18 285 0.4501545140 4549-05 3/8 10.0 10-50 7,5-37 335 0.540

Code No. a „

a Nm lbf·ft y 0

7601610 4550-20 1/2 12.5 40-200 30-150 485 1.107674330 4550-40 3/4 20.0 80-400 60-300 665 1.867674760 4550-55 3/4 20.0 110-550 80-405 960 3.561521365 4550-75 3/4 20.0 150-750 110-550 1240 4.50

Code No. : „ Nm lbf·in y 0

1646206 4101-05 9x12 5-50 3,5-37 325 0.640

Code No. : „ Nm y 0

7601960 4150-25 9x12 2-25 180 0.2107602180 4150-50 9x12 5-50 240 0.2707602850 4150-85 9x12 15-85 320 0.3407603580 4151-20 14x18 20-200 400 0.750

DREMASTER ®Robust torque wrench with square drive and integrated ratchet-head function for controlled bi-directional tightening and interchangeable mushroom head with push-button release.

Handgrip with a user aid Black plastic handgrip, new ergonomically enhanced shape, with an indentation in the middle of the handgrip. User aid and reference points for calibration.

Ligthweight and reliable Locking button enables reliable locking of the torque setting. Torque adjustable reference by means of opened lock symbol. Provision for rapid setting from the separate hexagon allen key �xture.

Nonius Model-dependent intervals of 1 or 0.5Nm allow for very accurate settings.

Dual scale with main and alternative unit (Nm/Ibf·ft). Main unit Nm with vernier. At all times only one unit in the viewing area = avoids any reading errors. Change-over switch next to the scale for straightforward unit selection.

Chrome plated ratchet head All 1/2” square drives of the DREMASTER DMK-series have a black plastic cap – also referred to as a mushroom head. This mushroom head prevents an unintentional pulling out of the whole square drive when changing the socket.

Classi�ed to DIN EN ISO 6789:2003Type II Class A, with a factory certi�cate allowing for operations to be traced back. Calibrated to a permitted +/- 3% deviation and better. Exceeding the speci�cations standard of +/- 4%.

Robust steel tube With high corrosion protection, chrome plated, satin powder coated.

Additional protection of the serial number Concealed setting drill hole = secured adjusting/setting system serial number on the wrench and on the certi�cate for unambiguous product identi�cation, traceable via in-house DAkkS laboratory to national standards.

Automatic actuation The DREMASTER® DMK actuates with a clear tactile impulse and audible signal and is immediately ready for operation again.

2995832 01/16

GEDORE Werkzeugfabrik GmbH & Co. KGRemscheider Straße 14942899 Remscheid · GERMANY

Vertrieb DEUTSCHLANDFon +49 2191 596-900 Fax +49 2191 596-999 [email protected]

Sales INTERNATIONALFon +49 2191 596-910 Fax +49 2191 596-911www.gedore.com

1

2

3

180°

Technical informationAnti-loss attachment

Function

All the benefits at a single glance

In order to change the turning direction of the DREMASTER® DMK:Press on the push-button with your thumb and take out the mushroom head. Turn the wrench and re-insert the square drive.

› Additional protection of the serial number. › Concealed setting drill hole. › Engaging adjusting button with locking reference (lock symbol). › Rapid adjustment provision using a separate hexagon allen key. › Mushroom head with release button and soft component.

› Plastic grip with soft component. › Dual scale (main unit with vernier). › At all times only one unit in the viewing area (Nm or lbf·ft). › Change-over switch for selecting the unit. › Controlled safety via in-house DAkkS test laboratory.

160

TORQUE TOOLS

DREMASTER®

DMK TORQUE WRENCH DREMASTER®20-850Nm / 15-630lbf·ft

Use: › For use in all areas of industrial manufacturing. › For controlled nut and bolt tightening.

Features: › Adjustable torque wrench with a square drive and integrated ratchet head function. › For controlled bi-directional tightening. › Interchangeable mushroom head square drive with ball-locking mechanism as per DIN 3120. › In accordance with DIN EN ISO 6789, traceable to national norms. › Lever breaking mechanism with a castor guarantee tactile impulse and audible actuation signals.

› Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Sturdy, satin-chrome plated tubular steel construction, with chrome plated

ratchet head and top grade plastic parts. › Ergonomically shaped, two-component plastic grip with calibration aid. › Double scale Nm and lbf.ft behind window with magnifying e�ect. › Additional micrometer scale with a Nm graduation of 0.1, 0.25, 0.5 or 1Nm. › Supplied with a calibration certi�cate. › Unique serial number for traceability.

Code No. a „

a Nm lbf·ft 9 Scale ring y 0

2641232 DMK 100 1/2 12.5 20-100 15-75 5 N·m 0,5 N·m 423.5 1.102641240 DMK 200 1/2 12.5 40-200 30-150 10 N·m 1 N·m 514.5 1.302641259 DMK 300 1/2 12.5 60-300 45-220 10 N·m 1 N·m 606.4 1.502641267 DMK 400 3/4 20.0 80-400 60-300 10 N·m 1 N·m 714.8 2.402641275 DMK 550 3/4 20.0 110-550 80-405 10 N·m 1 N·m 953.2 3.802641283 DMK 750 3/4 20.0 150-750 110-550 10 N·m 1 N·m 1,228.2 4.902641291 DMK 850 3/4 20.0 250-850 185-630 10 N·m 1 N·m 1,375.2 5.20

DMSE TORQUE WRENCH DREMASTER® 20-400Nm / 15-300lbf·ft

Code No. : Nm lbf·ft 9 Scale ring y 0

2641445 DMSE 100 9x12 20-100 15-75 5 N·m 0,5 N·m 398.5 1.002641453 DMSE 150 9x12 30-150 22-110 10 N·m 1 N·m 489.5 1.162641461 DMSE 200 14x18 40-200 30-150 10 N·m 1 N·m 499.5 1.252641488 DMSE 300 14x18 60-300 45-220 10 N·m 1 N·m 590.4 1.402641496 DMSE 400 14x18 80-400 60-300 10 N·m 1 N·m 677.2 2.00

Use: › For use in all areas of industrial manufacturing. › For controlled nut and bolt tightening.

Features: › Adjustable torque wrench with a spigot end. › For controlled bi-directional tightening. › Interchangeable mushroom head square drive with ball-locking mechanism as per DIN 3120. › In accordance with DIN EN ISO 6789, traceable to national norms. › Lever breaking mechanism with a castor guarantee tactile impulse and audible actuation signals.

› Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Sturdy, satin-chrome plated tubular steel construction, with chrome plated ratchet

head and top grade plastic parts. › Ergonomically shaped, two-component plastic grip with calibration aid. › Double scale Nm and lbf.ft behind window with magnifying e�ect. › Additional micrometer scale with a Nm graduation of 0.1, 0.25, 0.5 or 1Nm. › Supplied with a calibration certi�cate. › Unique serial number for traceability.

9x12

161

1

2

3

t L b - f 6-2000Nm

Z 8-1000Nm

SE } ~ 8-400Nm

s b - g 6-3000Nm

DREMOMETER PERMANENT PRECISIONTorque wrench made of high-strength aluminium alloy

Drive in accordance with application DREMOMETERS are available for a large variety of applications in controlled screw tightening. The single square drive for controlled clockwise tightening or the double square drive (L) for controlled bi-directional tightening. Special utilisation areas for DREMOMETER with spigot end (Z) and rectangular cavity (SE) particularly for hard-to-access locations and where space is tight. Almost all DREMOMETER models have separate ratchet heads, and there are good reasons for that: It is possible to work with or without the ratchet head function as desired.

Robust and unsusceptible The full-metal construction of the DREMOMETER makes it particularly unsusceptible to grime and rough handling on construction sites, in workshops and in industry.

ModelClassi�ed to DIN EN ISO 6789:2003 Type II Class A, with a factory certi�cate allowing for operations to be traced back. Calibrated to a permitted +/- 3% deviation and better. The speci�cations of the standard (+/- 4%) are exceeded.

Automatic resetting The DREMOMETER gives the operator an audible signal and tactile impulse and is back in operation in an instant.

The quality lever chain produced in Gedore‘s own drop forge reduces the strain on the mechanics to a minimum. The proportioning of the individual levers, which are optimally attuned to each other, gives the DREMOMETER its unique precision and its long tool life.

1 Position of the lever chain without impact of force (in starting position).

2 Position of the lever chain with impact of force before the set torque is achieved. The force is transferred from the primary lever to the intermediary and �nal lever until the �nal lever slips past the so-called release lever through the sliding back of the angle-lever body.

3 Position of the lever chain when the force impacts after the torque setting is achieved. Immediate position after the clear tactile impulse and audible signal click. On relief, the lever chain moves back into the starting position (1).

Working principle

162

TORQUE TOOLS

A+S

Maximum precision Extended tool life and long life-cycle even if used intensely.

› Serial number on the wrench and on the certi�cate for product identi�cation and traceability.

Scale Clear dual scale Nm and lbf·in/lbf·ft on every DREMOMETER (apart from models E / EL / EK / EKL / F).

Regardless of where you apply the force, at the centre of the handgrip or another part of the DREMOMETER, with both hands or using an extension tube, your torque setting will always be attained, without shifts in value. Due to its unique single-axis location of the centre of rotation and the output square drive, the DREMOMETER is a tool that can be operated free from errors. In contrast to conventional torque wrenches, this single lever enables tightening without shifts in the measured value and without interference caused by activation outside of the handgrip.

Setting of the torque value to Nm or alternatively to lbf·in / lbf·ft by the non-losable hexagon key in the handgrip. The smooth-running mechanism enables the setting to be made quickly without signi�cant force needing to be applied.

All DREMOMETERS are also available with locking and safely device (A+S).

However, value shifts are possible when activating the DREMOMETER with special wrenches or when using wrenches with di�erent depth gauges.

DREMOMETER Operable without inaccuracies

Features

Lightweight and pleasant The aluminium housing and the ergonomically designed handgrip enable simple and safe operation over wide tightening ranges.

1

2

3

163

164

TORQUE TOOLS

8554 TORQUE WRENCH DREMOMETER6-30Nm / 50-270lbf·in

DREMOMETER

Code Type No. a „

a Contents 9 Nm lbf·in y 0

7775440 s 8554-01 1/4 6.3 ! in plastic box 1Nm / 10lbf·in 6-30 50-270 265 0.580

8560 TORQUE WRENCH DREMOMETER8-40Nm / 70-350lbf·in

Code Type No. a „


7682000 s 8560-01 3/8 10 ! in plastic box 5Nm / 50lbf·in 8-40 70-350 338 1.00

8561 TORQUE WRENCH DREMOMETER20-120Nm / 15-90lbf·ft

Code Type No. a „

a Contents 9 Nm lbf·ft y 0

7683320 s 8561-01 1/2 12.5 ! in plastic box 5Nm / 5lbf·ft 20-120 15-90 462 1.50


Features: › Adjustable torque wrench with a 1/2”single square drive for controlled clockwise tightening. › 1/2” square drive with ball-locking mechanism as per DIN 3120. › In accordance with DIN EN ISO 6789, traceable to national norms. › Automatic short path actuation with tactile impulse and audible signal. › Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Full-metal construction from high strength aluminium alloy. › Double scale Nm and lbf.ft with scale graduation of 1Nm and 10lbf.in. › Supplied with a calibration certi�cate. › Unique serial number for traceability.


Features: › Adjustable torque wrench with a 1/4” single square drive for controlled clockwise tightening. › 1/4” square drive with ball-locking mechanism as per DIN 3120. › In accordance with DIN EN ISO 6789, traceable to national norms. › Automatic short path actuation with tactile impulse and audible signal. › Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Full-metal construction from high strength aluminium alloy. › Double scale Nm and lbf.ft with scale graduation of 1Nm and 10lbf.in. › Supplied with a calibration certi�cate. › Unique serial number for traceability.


Features: › Adjustable torque wrench with a 3/8”single square drive for controlled clockwise tightening. › 3/8” square drive with ball-locking mechanism as per DIN 3120. › In accordance with DIN EN ISO 6789, traceable to national norms. › Automatic short path actuation with tactile impulse and audible signal. › Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Full-metal construction from high strength aluminium alloy. › Double scale Nm and lbf.ft with scale graduation of 1Nm and 10lbf.in. › Supplied with a calibration certi�cate. › Unique serial number for traceability.

165


Code Type No. a „





8573 TORQUE WRENCH DREMOMETER40-200Nm / 30-150lbf·ftUse: › For use in almost all industrial manufacturing areas. › For controlled nut and bolt tightening.


Code Type No. a „



Code Type No. a „


7670180 s 8563-01 with extension tube 3/4 20 ! in plastic box 5Nm / 5lbf·ft 140-760 105-560 1400 5.007691500 s 8563-10 3/4 20 ! in plastic box 140-760 105-560 812 2.90



8563 D & DR TORQUE WRENCH DREMOMETER140-760Nm / 105-560lbf·ft

166

TORQUE TOOLS

8564 TORQUE WRENCH DREMOMETER750-2000Nm


Code Type No. a „


7688470 s 8570-10 3/4 20 ! in plastic box 5Nm / 5lbf·ft 80-360 60-260 718 2.40






Code Type No. a „


7694010 s 8571-01 3/4 20 ! in plastic box with ALU extension tube

10Nm / 10lbf·ft 520-1000 380-730 800-1400 5.10

Code Type No. a „

a Contents 9 Nm y 0

7695250 s 8564-01 1 25 ! with 2 extension tubes 50Nm 750-2000 932-2353 11.60


Features: › Adjustable torque wrench with a 1” single square drive for controlled clockwise tightening. › 1” square drive with ball-locking mechanism as per DIN 3120. › In accordance with DIN EN ISO 6789, traceable to national norms. › Automatic short path actuation with tactile impulse and audible signal. › Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Full-metal construction from high strength aluminium alloy. › Single scale Nm with scale graduation of 50Nm. › Extension tube with maximum lever length of 1998mm. › Supplied with a calibration certi�cate. › Unique serial number for traceability.

167

8572 TORQUE WRENCH DREMOMETER1500-3000Nm

Code Type No. a „

a Contents 9 Nm y 0

7717160 s 8572-01 1.1/2 40 ! with 2 extension tubes 50Nm 1500-3000 1423-2343 13.20


Features: › Adjustable torque wrench with a 1.1/2” single square drive for controlled clockwise tightening. › 1.1/2” square drive with ball-locking mechanism as per DIN 3120. › In accordance with DIN EN ISO 6789, traceable to national norms. › Automatic short path actuation with tactile impulse and audible signal. › Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Full-metal construction from high strength aluminium alloy. › Double scale with scale graduation of 50Nm. › Extension tube with maximum lever length of 2343mm. › Supplied with a calibration certi�cate. › Unique serial number for traceability.

753 TORQUE WRENCH DREMOMETER MINI2-12Nm

Code Type No. a „


1957694 Mini 753-11 1/4 6.3 ! in plastic box 0,5Nm / lbf·in + 0,05Nm 2-12 18-106 211 0.320


Features: › Adjustable torque wrench with a 1/4” single square drive for controlled clockwise tightening. › 1/4” square drive with ball-locking mechanism as per DIN 3120. › In accordance with DIN EN ISO 6789, traceable to national norms. › Automatic short path actuation with tactile impulse and audible signal. › Actuation accuracy: +/- 3% tolerance of the scale set to torque. › Window with a magnifying-glass e�ect. › Double scale with a scale graduation of 0.5Nm and 5 lbf·in. › Additional micrometer scale for setting interim values with Nm, graduations of 0.05Nm › Supplied with a calibration certi�cate. › Unique serial number for traceability.

8200 TORQUE ANGLE INDICATOR

Code No. a „

Q „

, A° 0

1195980 8200-01 1/2 1/2 80 0-360 0.330

Use: › Additional angle regulated tightening for controlled torque and angle activation.

Features: › F or additional precise angle tightening (0 - 360°) › 1/2“ square drive with ball-locking device. › With sliding magnetic and gripping arm. › For use with a suitable torque wrench. › The maximum output of the torque wrench must not be exceeded.

168

TORQUE TOOLS

TSN SLIPPERPre-set ratchet head torque wrench with automatic actuation and slip function. Over-tightening is not possible.

Integrated ratchet function Particularly dependable ratchet having 36 teeth (759-00/-01) or 48 teeth (759-02/-03). Slip-through function guarantees controlled and safe screw tightening, even in hard-to-access locations.

High repeatability Guarantees constant tightening torques.

Output square drive Made of quality steel with ball-locking mechanism

Robust casting part Made of corrosion-resistant, rustproof material.

Rubber handgrip Ergonomic and pleasant to hold in your hand. Prevents slipping.

Technical information

TSN SLIPPER & TBN BREAKER

Working principle

TSN SLIPPER All TSN Slipper and TBN Breaker torque wrenches (apart from 760-00/-01) are �tted with the patented Mechanical Torque Adjustment Locking Device to modify torque tester.

When the pre-set torque value is achieved, the mechanism slips through over the ball (without the possibility of over-tightening). The torque wrench is then immediately ready for the next operation.

Use: › For use in all areas of production line assembly. › For controlled nut and bolt tightening.

Features: › Pre-set production torque wrench without scale. › Square drive with ball-locking mechanism. › Integrated ratchet function for bi-directional tightening. › In accordance with DIN EN ISO 6789, traceable to national norms.

› Actuation accuracy: +/-4% tolerance of the set torque. › Precision mechanism slides through very noticeably and audibly when the pre-set

torque is achieved – over tightening is not possible. › Automatic resetting to the starting position. › Lightweight yet stable and corrosion resistant construction design. › Black, non-slip rubber handgrip. › Supplied with a calibration certi�cate. › Unique serial number for traceability.

759 TORQUE WRENCH TSN SLIPPER3-125Nm / pre-set

Code No. a „

a Nm y 0

7091900 759-00 1/4 6.3 5-25 216 0.3407092040 759-01 1/4 6.3 5-25 216 0.3407092120 759-02 3/8 10.0 15-55 324 0.8007092200 759-03 1/2 12.5 40-125 460 1.360

Use: › For use in all areas of assembly work where controlled tightening with low torque values is required

(eg electronic hardware sector). › For controlled nut and bolt tightening.

Features: › Pre-set production torque wrench without scale. › Square drive with ball-locking mechanism. › Integrated ratchet function for bi-directional tightening. › In accordance with DIN EN ISO 6789, traceable to national norms.

› Actuation accuracy: +/-6% tolerance of the set torque. › Precision mechanism slides through very noticeably and audibly when the pre-set

torque is achieved – over tightening is not possible. › Automatic resetting to the starting position. › Lightweight yet stable and corrosion resistant construction design. › ESD (electrostatic discharge) = electrostatically protected. › Black, non-slip rubber handgrip. › Supplied with a calibration certi�cate. › Unique serial number for traceability.



Features: › Improved control of the fastening process by reducing the risk of both under and over tightening. › Unique slipping mechanism, which gives the operator more time to react once the target torque is

reached. › Actuation accuracy: +/- 6% tolerance of the set torque.

› Maintains production output by minimising operator fatigue through the tool’s ergonomic design. › Maximises productivity in restricted space through its compact slimline design. › EPA compliant for use in electrostatically sensitive applications. › Drive type made of stainless steel. › Supplied with a calibration certi�cate. › Unique serial number for traceability. › Accessories available.



Features: › Square drive with ball-locking mechanism. › Integrated ratchet function for bi-directional tightening. › In accordance with DIN EN ISO 6789, traceable to national norms. › Actuation accuracy: +/-6% tolerance of the set torque.

› Precision mechanism slides through very noticeably and audibly when the pre-set torque is achieved – over tightening is not possible. › Automatic resetting to the starting position. › Lightweight yet stable and corrosion resistant construction design. › ESD (electrostatic discharge) = electrostatically protected. › Black, non-slip rubber handgrip. › Supplied with a calibration certi�cate. › Unique serial number for traceability.

169

762 TORQUE WRENCH TSC SLIPPER1-10Nm

761 TORQUE WRENCH TSP SLIPPER1-10Nm / pre-set

Code No. a „

a Nm y 0

1196650 761-05 1/4 6.3 1-5 185 0.1901196731 761-10 1/4 6.3 2-10 185 0.190

Code No. a „

a Nm y 0

1196480 762-05 1/4 6.3 1-5 195 0.2351196510 761-10 1/4 6.3 2-10 195 0.235

TSC TORQUE WRENCH ADJUSTABLE SLIPPER10-90Nm

Code No. a „

a Nm y 0

056060 TSC-45 1/4 6.3 10-45 195 0.235056080 TSC-90 1/4 6.3 20-90 195 0.235

170

TORQUE TOOLS

TBN BREAKERPre-set torque wrench with automatic snap actuation. Torque wrench offering maximum accuracy. Guaranteed tightening values without over-tightening.

Drive 16mm spigot end or 9x12mm rectangular cavity made of quality steel with pin-locking mechanism.

Breaking All TBN breaking torque wrenches break by 20° at the pivot point when the set torque is achieved. The models 760-00/-01 can also be set to a breaking angle of 90°.

Lightweight steel tube Firm, solid, and free of corrosion.

Patented mechanism Guarantees a long product lifespan with guaranteed accuracy values.

Working principle

TBN BREAKER

Technical information

TBN BREAKERWhen the TBN breaking torque wrench is operated, the rear section of the driver unit presses the roller. When the pre-set torque value is achieved, the lever switches over and the front section of the drive unit breaks.

TBN Breaker 760-00/-01 values are changed using the Double Positive adjustment system.

As an option, Gedore also manufactures the TBN Breaker models 760-00/-01 with interchangeable �ttings directly positioned on the tool.

TBN Knicker j 5 - 135Nm

TBN Knicker } 0,2 - 135Nm

Rubber handgrip: Ergonomic and pleasant to hold in your hand. Prevents slipping.

9x12 16

TBN-65

TBN-135G

TBN-25G

171

Code No. Ø : EPA Nm lbf·in y 0

7090690 TBN-2G 9x12 x 0.4-2 1.8-18 133 0.125

7090770 TBN-10G 9x12 x 1-10 9-89 133 0.145

1824694 TBN-25G 9x12 5-25 44-221 265 0.405

1824716 TBN-65G 9x12 10-65 89-575 302 0.745

1824732 TBN-135G 9x12 25-135 177-1195 408 1.03

050310 TBN-200G 14x18 40-200 520 1.40

1825686 TBN-25 16 5-25 44-221 265 0.4101824708 TBN-65 16 10-65 89-575 302 0.7501824724 TBN-135 16 20-135 177-1195 408 1.03050300 TBN-200 16 40-200 520 1.40

Use: › For controlled nut and bolt tightening. › For use in all areas of production line assembly. › Extremely durable.

Features: › Pre-set production torque wrench – without scale › With 9x12mm rectangular cavity end or 16mm spigot-end. › For bi-directional tightening (the wrench only has to be turned by 180°). › Actuation accuracy: +/- 4% tolerance of the set torque. › Precision mechanism slides through very noticeably and audibly when the pre-set

torque is achieved – over tightening is not possible. › Automatic resetting to the starting position. › Lightweight yet stable and corrosion resistant construction design. › Black, non-slip rubber handgrip. › No. 760-00/-01: EPA (Electrostatic Protected Area) compliant. › The TBN range is available with a variety of end �tting styles.

ATB SE ADJUSTABLE BREAKING TORQUE WRENCH1-10Nm

Code No. : ISO y 0

2839636 ATB-5G 9x12 1-5 230 0.2902839644 ATB-10G 9x12 2-10 230 0.300

Use: › Controlled bolt and nut tightening. › For use in all areas of production line assembly. › Extremely durable.

Features: › Compact design allows easy access where space is restricted. › With 9x12 mm rectangular end. › O�ers improved control of the tightening process by reducing the risk of under and over

tightening. This is achieved by Torqueleader’s unique breaking mechanism that allows the operator more time to react once the target torque is achieved. › Accuracy +/- 6% of reading. › Reduces the likelihood of warranty and rework by assuring process control through accurate and

repeatable torque application. › Automatic resetting to the starting position. › Fast and accurate to set using the quick and clear to read micrometer setting scale. › Black, non-slip rubber handgrip. › This tool is length dependent, with hand position altering the torque applied. › Accessories available.

TBN-65

TBN-135G

760 BREAKING TORQUE WRENCH TBN0,4-200Nm / 44-147lbf·in / pre-set

9x12

Torque wrench Type 88

8801 TORQUE WRENCH150-1500Nm

Use: › Controlled bolt and nut tightening in the range 100 - 1500Nm. › For use in all areas of industry, automotive sector and machine maintenance.

Features: › Adjustable torque wrench with scale. › 3/4"square drive with integrated ratchet function. › Push-through square drive for bi-directional tightening. › In accordance with DIN EN ISO 6789, traceable to national norms.

› Breaker mechanism (handle snaps over) is seen and felt when selected torque is reached, reducing the likelihood of over tightening. › Dual scale in Nm and lbf·ft › Actuation accuracy: +/- 4% tolerance of the value setting. › 4 models in the range 150 - 1500Nm › Robust construction. › Supplied with a calibration certi�cate and unique serial number for traceability. › Delivered in sturdy cardboard packaging

TT3KH ELECTRONIC TORQUE WRENCH TORCOTRONIC III70-350Nm / 51.6-258.2lbf·ft

Use: › For everyday requirements in installation and torque control. › For use in all areas of manufacturing and development.

Features: › Microprocessor controlled, electronic torque wrench with CE symbol. › For controlled bi-directional tightening › Broad measurement range in Nm, can be switched to lbf·ft. › With 1/2” reversible ratchet. The ratchet is exchangeable, providing the option of using a 9x12mm (8455-120) or 14x18mm (8455-350) square socket.

Characteristics: › Torque and torque angle measure. › 5 di�erent measuring modes. › 5 parameters storable. › USB interface for data exchange. › 2000 storage places › High measurement accuracy: +/-1% tolerance for all read-o� values, +/-1 digit. › Di�erent depth gauges for end �ttings programmable. › Simple to operate with easy to understand icon-menu navigation and 4 functional keys. › Clearly readable, illuminated LCD display.

› Resolution torque: 0.1Nm. › Resolution torque angle: 0.1°. › PC-software easy to operate for uncomplicated programming and

documentation of data. › Data can be transfered to MS Excel®. › Keyboard lock. › Operation with standard Mignon AA or optional with rechargeable-battery (NiMH). › Visual signal: 3x LED (yellow, green, red). › Acoustic signal: buzzer.

Scope of delivery: › Electronic torque wrench TorcoTronic III HighLine. › Reversible ratchet 1/2". › USB cable. › Software on CD-R. › Supplied with a calibration certi�cate. › Delivered in a transparent plastic box with insert.

Attention: › A PC, running Windows® operating system (from Windows XP®) is required to obtain the full bene�t of

all the functions of this product.

Torcotronic 3

172

TORQUE TOOLS

Code Code a „

a 9 Nm y 0

3022854 8801-01 3/4 20 10Nm 150-700 915 5.503022862 8801-02 3/4 20 10Nm 200-800 1090 6.003022870 8801-03 3/4 20 20Nm 300-1000 1470 7.303022889 8801-04 3/4 20 25Nm 700-1500 1470 10.00

Code Code a „

a : N·m lbf·ft 0

2648644 TT3KH-350 1/2 12.5 14x18 51.6-258.2 70-350 1.20

8301

8302

8301 - 8302 TORQUE WRENCH WITH SLAVE POINTER0.8-200Nm

Use: › Controlled tightening and veri�cation of tightening values. › For use in all areas of industrial manufacturing and quality control. › Working ranges of 0.8 to 200Nm are covered.

Features: › Dial-indicating torque wrench with dual scale and multi-functional slave pointer. › 1/4", 3/8", 1/2" double-square drive with ball locking device for controlled bi-directional tightening. › Models 8301-04 to 8302-20: With integrated ratchet function. › For controlled screw tightening and torque measurements. › Working accuracy: +/- 4% tolerance of the indicated torque. › Double scale in Nm and lbf·in or lbf·ft double tinted clearly readable face. › Integrated overload protection – mechanical stop up to maximum 25% overload of the maximum

value. › Housing made of lightweight, robust special aluminium construction – lacquered, silver-grey. › Black, non-slip rubber handgrips. › Models 8301-04 to 8301-40: EPA-conformant (Electrostatic Protected Area), for use in sensitive

electrostatic applications.

Scope of delivery: › Dial-measuring torque wrench type 83. › Test certi�cate accoring to DIN EN ISO 6789. › Delivered in a sturdy black plastic box (no. 8301-04 to 8302-20).

Torque wrench Type 83

TORQUE WRENCHES WITH SLAVE POINTERIDEAL FOR TEST, CONTROL AND MAINTENANCE WORK

Clear product identi�cation: Provided by the type plate/lable.

The article number and the serial number always ensure traceabili-

ty in the scope of your test- and checking-tool management.

Practical handgrip: Handgrip shaped in

accordance with the most recent ergonomic

�ndings. Resistant to grease and oil.

Solid tube: Light-metal tube

with plastic sleeving.

Dual scale: Nm and lbf·in/lbf·ft with main

and slave pointers, protected by a strong

window made of Trogamid T.

Integrated ratchet spindle: With double square drive enab-

les high-speed bi-directional

tightening.

FEATURES

The working principle of the torque wrench with slave pointer type 83

173

Code Code Type a „

a 9 Nm lbf·in Height y EPA 0

7651390 8301-04 t 1/4 6.3 0,1Nm / 1lbf·in 0,8-4 7-35 61 244 x 0,507651470 8301-12 t 1/4 6.3 0,5Nm / 2lbf·in 2,4-12 21-105 61 244 x 0,507651550 8301-25 t 3/8 10.0 1Nm / 10lbf·in 5-25 44-240 69 244 x 0,507651630 8301-40 t 3/8 10.0 1Nm / 10lbf·in 8-40 72-360 69 244 x 0,507651710 8302-08 t 1/2 12.5 2Nm / 1lbf·ft 16-80 12-60 86 435 1.407651980 8302-20 t 1/2 12.5 5Nm / 5lbf·ft 40-200 30-160 86 435 1.40

TORQUE SCREWDRIVERS 756

1/4" drive type: Made

of stainless steel, for

industry-standard bits.

Sliding T-Bar: Made of qua-

lity steel, can be adapted to

enhance users, transmission

of power.

Rubber handgrip: Ergonomic, can

be held securely in your hand.

Scale: Clearly readable scale ring; enables

you to make the setting accurately, quickly

and without error.

Positive-Lock system: Locks the

set torque, reliably preventing it from

wrong setting.

756 TORQUE SCREWDRIVER TYPE S0.24-9Nm

Code Code a „

a - „

- 9 Nm cN.m Height y 0

1400150 756-01 1/4 6.3 1/4 6.3 1cNm 0,24-1,2 20-120 61 183 0,1651400169 756-06 1/4 6.3 1/4 6.3 0,1Nm 1-6 120-600 61 196 0,3401400177 756-09 1/4 6.3 1/4 6.3 0,1Nm 4-9 400-900 69 196 0,340

Use: › For controlled screw tightening. › For use in electrical hardware, industrial manufacturing or in quality control.

Features: › Adjustable torque screwdriver – with scale. › With 1/4" female hexagon drive for use with 1/4" hexagon bits. › Actuation accuracy: +/- 6% tolerance of the set torque. › In accordance with DIN EN ISO 6789, traceable to national norms. › Precision radial ball clutch and cam design for controlled bi-directional tightening › Precision mechanism slips through very noticeably when the pre-set torque is achieved. › Automatic resetting to the starting position. › With set-torque-locking ‘positive-lock’ system, automatically �xes the set torque. › Non-slip rubber handgrip. › Micrometer scaling: 1cNm and 0.1Nm.

› EPA-conformant (Electrostatic Protected Area), for use in sensitive electrostatic applications

Scope of delivery: › Torque wrench type 756. › 1/4" square/hexagon drive adapter (no. 757-20). › Models 756-06/-09 with additional sliding T-bar for ease of use. › Supplied with a calibration certi�cate. › Unique serial number for traceability.

TLS PRO PRESET TORQUE SCREWDRIVER0.05-13.5Nm

Code Code - „

- Nm cNm y 0

065400 TLS PRO 25H 1/4 6.3 0.05-0.25 5-25 132 0.210065500 TLS PRO 150H 1/4 6.3 0.2-1.5 20-150 132 0.210065600 TLS PRO 450H 1/4 6.3 0.5-4.5 50-450 140 0.230065700 TLS PRO 1350H 1/4 6.3 2.5-13.5 250-1350 140 0.230

› Accurate process control is ensured by eliminating under and over tightening due to Torqueleader’s proven slipping technology. › Years of dependable service is provided by the robust design especially if regularly calibrated. › Calibration stickers can be easily applied to the purpose designed nose. › To allow for customisation and clear identi�cation, interchangeable coloured end caps are available. › Increased production e�ciency by reducing operator fatigue due to a speci�cally

designed ergonomic handgrip combined with a smooth tool reset action. › To assist with higher torque, T-bars come standard with the Pro and ESD 450 and 1350 models.

174

TORQUE TOOLS

Torque calibration analysers

8612 ELECTRONIC TORQUE TESTER DREMOTEST E0.9-3150Nm

8612-050 – 8612-3150Use: › For verifying and setting clockwise torque wrenches and torque screwdrivers.

Features: › Simple, electronic torque tester with integrated torque transducer (DMS). › 4 models in the range from 0.9 to 3150Nm. › Model 8612-3150 with 10mm, 17mm and 36mm hexagonal socket (size dependent). › Model 8612-3150 with 1“ square drive adapter. › Models 8612-050 - 8612-1000 with 1/4", 3/8" or 1/2"square drive adapter (depending on the size). › High measurement accuracy: +/- 1 % tolerance of reading, +/- 1 digit. › Break-point measurement (1st peak). › Auto reset. › Can be switched from Nm to lbf·ft. › Serial RS232 interface.

Scope of delivery: › Electronic torque tester. › RS232 cable. › Power supply unit. › 100 - 240 V, 50 - 60 Hz, maximum 500mA (see type plate). › 2 sockets (size and drive model-dependent). › Adapter for 8612-3150. › Operating instructions.

8612-720 – 8612-740 › Guaranteed measuring accuracy: +/-2% of read-out in the core range of 20-100% of the scale. › Double scale in cNm and ozf.in or Nm and lbf.in. › For testing and setting clockwise torque wrenches and screwdrivers in the lower torque

range of 0-25Nm.

8612-720

8612-300

8612-3150

502 MOTORIST TOOLKIT 113 1425/41/D19 134

175

Code No. - - „

a „ Resolution Adapter Q

„ lbf·ft Nm cNm/Nm ozf.in/lbf.in Gradation 0

1824635 8612-720 1/4 1/4 26-130 36-180 2cNm/2ozf.in 10.01824651 8612-740 1/4, 3/8 2.4-12 0.2-2 0.2Nm/2lbf.in 3.2

1947699 8612-050 10 0.01 1/4, 3/8 0.7-40.6 0.9-55 3.01856111 8612-300 17 0.1 3/8, 1/2 7-236 90-320 3.01947702 8612-1000 36 1 1/2, 3/4 66-811 90-1100 10.02529858 8612-3150 1 1 369-2323 500-3150 26.0

CAPTURE SYSTEM A NEW STANDARD IN TORQUE ANALYSER SYSTEMS:

CAPTURE MANAGER PC SOFTWARE

KEY BENEFITS OF CAPTURE MANAGERPC software – e�ectively manage your data: › Manage tool and test data through the Capture Manager PC software.

The software also makes analysing the data quick and easy through integration with Microsoft Excel. › The Capture Manager PC software allows unlimited storage of tools and data readings which can be

uploaded and downloaded to the Capture Display via a USB connection. › Ensures tools are performing to the required standard through the ISO 6789:2003 test wizard.

This clear and easy to use feature guides the user through the test procedure. › Tool traceability can be achieved as the Capture Manager PC software can generate customised

calibration certi�cates to the requirements of ISO 6789:2003.

Code Code036710 Captura manager software

176

TORQUE TOOLS

Highly accurate measurement of hand and power torque tools, the System has been designed and tested in conjunction with the National Physical Laboratory in the UK, a world leader in electronic measurement systems.

Designed to allow users to become productive quickly, as the System is quick to set up and requires little training due to the System’s intuitive easy to use menus and Plug & Play connectivity.

The Capture System maximises torque tool test e�ciency as the Display, Sensor and Manager PC software have been designed to work together, automating many functions.

Versatile design allows static laboratory use and mobile data collection using an onboard memory and rechargeable battery. The data can then be transferred to PC via a USB connection.

CAPTURE DISPLAY

KEY BENEFITS OF CAPTURE DISPLAYIntuitive - easy to use: › Designed to allow users to become productive quickly due to its intuitive features, such as

easy to navigate menus, tool database and Plug & Play integration with Capture Sensors. › Versatile design allows static laboratory use and mobile data collection using an onboard memory and

rechargeable battery. The data can then be transferred to PC via a USB connection. › Minimise investment, as the Capture Display is designed to integrate with customers’ existing industry

standard nominal 2mV/V transducers. › To protect the Capture Display when not in use, it is supplied complete in a high-impact plastic carry-case.

In addition, the following items are included with the display and are stored in the case: USB power cable (for charging from mains or PC and also used for data transfer), power supply (multi-national), calibration certi�cate, start up guide and instructions. › Work for longer between battery charges as the unit is �tted with a long-life Lithium-ion battery and has an

auto power down mode.Technical information: › Capture Display can store 500 tools and 2000 data readings in the onboard memory.

Code Code036700 Capture display

CAPTURE SENSOR

KEY BENEFITS OF CAPTURE SENSOR › Built-in �exibility as the sensor can be mounted horizontally or vertically without the need for any accessories. › Fast to set up when used with a Capture Display due to the imbedded Quicktec technology which passes all the Sensor

information to the Display. › Remove human error from testing by using the Capture Sensor with the ISO 1500/90 Torque

Loading System (adaptor required). › To protect the Sensor when not in use it is supplied in a high-impact plastic carry-case. › Easy to repair due to a modular design that allows for simple component replacement. › For users with limited space who need to change Sensors between tests the Quick Change Plate increases

calibration productivity.Technical information: › Sensors come complete with UKAS certi�cate to BS 7882:2008 Class 1 or better. › Calibrated range is 10% to 100% of capacity. › Ranges covered 0.2-1500Nm.

Code No. Mounting hole size Nm Hole centres a „ H x W x D 0

036805 CS-2 M8 x 1.25 (10 Deep Min.) 0.2-2 56mm 1/4 62 x 85 x 65 0.500036810 CS-10 M8 x 1.25 (10 Deep Min.) 1-10 56mm 1/4 62 x 85 x 65 0.500036820 CS-50 M8 x 1.25 (10 Deep Min.) 5-50 56mm 3/8 62 x 85 x 65 0.570036830 CS-250 M12 x 1.75 (16 Deep Min.) 25-250 79mm 1/2 82 x 120 x 87 1.45036845 CS-1500 M16 x 2.00 (20 Deep Min.) 15-1500 125mm 1 100 x 165 x 134 4.00

Code Model036226 Capture Cable - CAPTURE to CUSTOM Sensor036246 Capture Cable - CAPTURE to CAPTURE Sensor036771 CAPTURE Sensor ISO 1500/90 AdapterD18205 CAPTURE Sensor ISO-A Mount036772 CAPTURE Sensor Quick Change Plate

177

7112-13

7118-19

7212-19

7218-19

178

TORQUE TOOLS

› For accessing bolts in cramped and hard-to-reach locations, easy to change. › Forged. › Chrome Vanadium steel, matt chrome plated. › With eject-pin for unlocking.

End fittings 9x12 / 14x18 SE

7112 / 7118 RECTANGULAR OPEN END FITTING9x12-14x18

7212 / 7218 RECTANGULAR RING END FITTING9x12-14x18

› For accessing bolts in cramped and hard-to-reach locations, easy to change. › Forged. › Chrome Vanadium steel, matt chrome plated. › With eject-pin for unlocking.

9x12

14x18

Code No. ! : 4 r Depth gauge 0

7688390 7112-07 7 9 x 12 5.5 20.0 17.5 0.0357688550 7112-08 8 9 x 12 5.5 21.5 17.5 0.0357679050 7112-09 9 9 x 12 5.5 23.0 17.5 0.0357688630 7112-10 10 9 x 12 5.5 24.5 17.5 0.0407688980 7112-11 11 9 x 12 5.5 26.0 17.5 0.0307679560 7112-12 12 9 x 12 5.5 27.5 17.5 0.0357689010 7112-13 13 9 x 12 5.5 29.0 17.5 0.0357689360 7112-14 14 9 x 12 7.5 31.0 20.0 0.0407689440 7112-15 15 9 x 12 7.5 33.0 20.0 0.0407679990 7112-16 16 9 x 12 7.5 35.0 20.0 0.0457689600 7112-17 17 9 x 12 7.5 37.0 20.0 0.0507684560 7112-18 18 9 x 12 7.5 39.0 20.0 0.0607689790 7112-19 19 9 x 12 7.5 41.0 20.0 0.060


7689870 7118-13 13 14 x 18 7 30.0 25.0 0.1207690020 7118-14 14 14 x 18 7 32.0 25.0 0.1207690100 7118-15 15 14 x 18 7 34.0 25.0 0.1207685610 7118-16 16 14 x 18 9 35.5 25.0 0.1307690370 7118-17 17 14 x 18 9 37.0 25.0 0.1307686180 7118-18 18 14 x 18 9 39.0 25.0 0.1307690450 7118-19 19 14 x 18 9 41.0 25.0 0.1307686420 7118-21 21 14 x 18 11 45.0 25.0 0.1557690610 7118-22 22 14 x 18 11 47.0 25.0 0.1507690880 7118-24 24 14 x 18 11 51.0 25.0 0.1707690960 7118-27 27 14 x 18 13 58.5 32.5 0.1857691260 7118-30 30 14 x 18 13 67.5 32.5 0.2207687740 7118-32 32 14 x 18 13 67.5 32.5 0.220


7691340 7212-07 7 9 x 12 8 13.0 17.5 0.0307691420 7212-08 8 9 x 12 8 14.2 17.5 0.0357691690 7212-10 10 9 x 12 8 17.2 17.5 0.0407691770 7212-11 11 9 x 12 8 18.6 17.5 0.0307677940 7212-12 12 9 x 12 12 20.0 17.5 0.0357691930 7212-13 13 9 x 12 12 21.5 17.5 0.0357692230 7212-14 14 9 x 12 12 23.0 17.5 0.0407692580 7212-15 15 9 x 12 12 24.0 17.5 0.0407678080 7212-16 16 9 x 12 13 26.0 17.5 0.0407692740 7212-17 17 9 x 12 13 27.0 17.5 0.0407678160 7212-18 18 9 x 12 13 28.5 17.5 0.0407692820 7212-19 19 9 x 12 13 30.5 17.5 0.0407678240 7212-21 21 9 x 12 15 33.0 17.5 0.040


7693120 7218-13 13 14 x 18 12.0 21.5 25 0.1207693390 7218-14 14 14 x 18 12.0 23.0 25 0.1207693470 7218-15 15 14 x 18 12.0 24.2 25 0.1207678320 7218-16 16 14 x 18 12.0 25.7 25 0.1257693630 7218-17 17 14 x 18 12.0 27.2 25 0.1257678830 7218-18 18 14 x 18 12.0 28.5 25 0.1257693710 7218-19 19 14 x 18 12.0 30.5 25 0.1257678910 7218-21 21 14 x 18 15.0 33.0 25 0.1407693980 7218-22 22 14 x 18 15.0 34.5 25 0.1407694280 7218-24 24 14 x 18 15.0 37.5 25 0.1407694440 7218-27 27 14 x 18 17.5 41.5 31 0.1507694790 7218-30 30 14 x 18 17.5 45.0 31 0.1607695920 7218-32 32 14 x 18 17.5 47.5 31 0.165

9x12

14x18

7412 / 7418 RECTANGULAR REVERSIBLE RATCHET HEAD9x12-14x18

› For accessing bolts in cramped and hard-to-reach locations, easy to change. › Forged. › Chrome Vanadium steel, matt chrome plated. › With eject-pin for unlocking. › Fine-toothed. › 7412 with return angle of 5 degrees › 7418 with return angle of 7 degrees › Maximum continuous load of ratchet according to DIN EN ISO 6789:2003 and/or maximum load of cavity.

754 RATCHET HEAD1/2“-1“

› Enables controlled torque tightening in combination with a DREMOMETER torque wrench. › Forged. › Made from Chrome Vanadium steel. › Fine-pitched, sturdy ratchet head. › With 1/2”, 3/4” and 1” output square drive. › For clockwise tightening.

7418

7412

179

9x12

14x18

Code No. a " : 4 r Depth gauge 0

7672710 7412-00 1/4 9 x 12 16.6 25 17.5 0.0607686500 7412-01 3/8 9 x 12 23.2 34 17.5 0.1407687230 7412-02 1/2 9 x 12 24.2 34 17.5 0.150

Code No. a „ : 4 r Depth gauge 0

7687580 7418-02 1/2 14 x 18 28.8 47 25 0.3507687660 7418-04 3/4 14 x 18 35.5 64 33 0.780

Code No. a „ 0

7680650 754-02 1/2 0.3507680730 754-04 3/4 1.007680810 754-06 1 2.50

180

TORQUE TOOLS

181

ToToTrque

ToToT rque950 lbf·f

tftf

200 lbf·ftftf

270 N·m

2011

Serien-No. DV02.00018

Ratio

Max.Output

ModelMax.Input

1 : 5

1300 N·m

TORQUE MULTIPLIERS

DREMOPLUS ALU

Safety Plus Your advantage

› The slender, lighter structure of the appliances ensures convenient and safe working – even where conditions are particularly cramped. › Repetition-accurate and precise results – supported by individual factory test certi�cates – ensure a maximum degree of job safety. › High degree of resilience and long life of the appliances attributable to a low-backlash planet gear with Ceramic-Te�on® coating. › A 30%+ lighter steel housing thanks to the use of high-performance aluminium. › Each torque multiplier is examined as to its torque range at the factory and provided with an individual factory test certi�cate. › Precise, reliable �gures – even under extreme climatic conditions › Easy to operate: The most common input/output torques on the torque multiplier.

182

WHAT MAKES A GOOD TORQUE

MULTIPLIER?

› Light yet with the appliance remaining sturdy. › The torque and repeatability accuracy is at +/-3%. Only in this way is dependable

screw tightening work assured with reproducible accuracy. › Both the torque settings and individual appliance components can be traced back. › A factory test certi�cate ensures traceability of operations on the basis of ISO 9000.

An individual factory test certi�cate is prepared for each and every torque multiplier and contains comprehensive information on readings, deviations, torque sensors and environmental in�uences.

› Particularly when unloosening seized screw connections, minimised impacts on the tooth �anks appear in a low backlash planet gear. The greater the precision with which the components �t together, the more stable the overall structure and the longer the service life. This precision can only be assured by a high in-house manufacturing proportion and consistent quality checks. › An overload safety mechanism should be integrated at torques upwards of 2000Nm.

No damage occurs to the gear should it be overloaded.

Selection criteria

1. Torque Select your torque multiplier on the basis of the maximum output torque.

2. Loading factor and frequency (load spectrum) It would be wrong to constantly operate the appliance at its maximum capacity – just as it would be for any machine or any car. This also holds good for the choice of the torque multiplier. Permanently operating a torque multiplier for screw- tightening applications at maximum torque may impact negatively on its service life.

3. Supporting situation Various supporting situations may be a determining factor in the selection of the torque multiplier.

Support at a raised position: The L-form reaction arm would be suitable should you want to attach the reaction arm to a point above the screw-tightening level. A warning here in that the inputted bending forces result in a reduction of the maximum permitted torque! Support at the level of the screw: Our recommendation – should you want to attach the reaction arm at the screw-tightening level – is either for a Z-form reaction arm or the straight L-form with adjustable reaction square.

4. Anti-wind-up ratchet A minimum 180° torque wrench �eld of movement should be on hand. As such, the recommendation is for an appliance complete with an anti-wind-up ratchet. In this way, pre-tension in the appliance is maintained and does not need to be recreated with each lift.

8000 screws a year are to be tightened at 4000Nm. The following calculation needs to be carried out on the basis of the diagram to �nd the right appliance:

Torque x 100%

Loading = 4.000Nm x 100%

62 %

Choose an appliance with a max. 6452 N·m torque. The DVV-60ZRS would be ideally suitable here.

Plan for a su�cient reserve in unloosening the screw connection. The torque needed to unloosen a screw connection can be many times the tightening torque.

Screw connections - quantity per year

Application case

182

TORQUE TOOLSTORQUE MULTIPLIERS

PRODUCT OVERVIEW TORQUE MULTIPLIERS

DREMOPLUS ALU

DVV-13 Z 3% 1/2" 3/4" 1:5 Z 250 – 1.300Nm

DVI-20 Z 3% 3/4" 1" 1:4 Z 500 – 2.000Nm

DVI-20L 3% 3/4" 1" 1:4 L 500 – 2.000Nm

DVI-28Z 3% 3/4" 1" 1:5,5 Z 500 – 2.800Nm

DVI-28L 3% 3/4" 1" 1:5,5 L 500 – 2.800Nm

DVV-40Z 3% 1/2" 1" 1:16 Z 500 – 4.000Nm

DVV-40ZRS 3% 1/2" 1" 1:16 Z 500 – 4.000Nm

DVV-60ZRS 3% 3/4" 1.1/2" 1:18 Z 700 – 6.000Nm

DVV-80ZRS 3% 3/4" 1.1/2" 1:22 Z 750 – 8.000Nm

DVV-100ZRS 3% 3/4" 1.1/2" 1:28,5 Z 1.000 – 10.000Nm

DVV-130ZRS 3% 3/4" 1.1/2" 1:39 Z 1.200 – 13.000Nm

DVV-540RS 3% 3/4" 2.1/2" 1:175 – 7.000 – 54.000Nm

Serie

s / Ty

pe

Ratio

Reac

tion

arm

Anti-

win

d-up

ratc

het

Overload safety mechanism

Sun

gear

Shea

ring

squa

re

Slip

per

non-

destr

uctiv

e

Cera

mic-

Te�o

n®

coat

ing

Rang

e Nm

te

sted a

nd ce

rti�c

ated

Outp

ut d

rive

Drive

Accu

racy

+ / -

183

INPUTN·m / lbf·ft

OUTPUTN·m/lbf·ft

INPUTN·m / lbf·ft

OUTPUTN·m/lbf·ft

INPUTN·m / lbf·ft

OUTPUTN·m/lbf·ft

INPUTN·m / lbf·ft

OUTPUTN·m/lbf·ft

INPUTN·m / lbf·ft

OUTPUTN·m/lbf·ft

INPUTN·m / lbf·ft

OUTPUTN·m/lbf·ft

INPUTN·m / lbf·ft

OUTPUTN·m/lbf·ft

INPUTN·m / lbf·ft

OUTPUTN·m/lbf·ft

N . mINPUT

N·m / lbf·ftOUTPUTN·m/lbf·ft

N . mINPUT


N . mINPUT


The chart representation elucidates the principle of torque multiplication. Let us assume a 60Nm input torque and a 240Nm output torque.

At a 1:4 ratio, 4 revolutions are needed at the input for 1 revolution with a 240Nm torque to be obtained at the output.

This is substantiated in terms of the physical formula:Power = torque x revolution

With gear e�ciency deducted, the output power is to be considered as a constant equal to the input power. Thus multiplication of the torque can only be obtained from an increased number of revolutions at the input.

When working with a torque multiplier, torsion wind-up is built up in the gear when the screw is tightened. This stress must be reduced. A reaction absorbed by a reaction arm and abutment is produced.

Working principleTorque - velocity

Working principleForce and reaction

Input torque with torque wrench 60Nm

4 revolutions

approximately 1 revolution

Output torque 240Nm

Torque Turning direction Reaction

L-form reaction arm with adjustable reaction square:The reaction acts on the adjacent impact socket.

Reaction arm in Z-form:The reaction acts on the adjacent screw connection.

L-form reaction arm without adjustable reaction square:The reaction acting on the wall is possible, but the tilting movement which arises causes the maximum permitted torque to drop by 20 %.

184


› A �exible o�set reaction arm which has proved itself as the standard solution. › Supporting situations are, for instance, adjoining screws, walls, machine parts and

other stable abutments. › This reaction arm can be ideally used where conditions are quite cramped.

Choosing the right reaction armReaction arm Z-form

› This straight reaction arm with adjustable reaction square is admirably suited for �ange screw connections. › The L-form reaction arm has in terms of support a larger radius

than the Z-form.

The L-form is also ideal for those points above the screw-tightening level. However, the resulting tilting moment causes the maximum permitted torque to drop by 20%.

Choosing the right reaction armReaction arm L-form

› It is vital that use is made of a torque wrench complete with ratchet function (integrated or separate) for torque multipliers without anti-wind-up ratchet. › For models with an anti-wind-up ratchet, we recommend the use of torque tools

complete with ratchet function (integrated or separate) for ease of working.

Choosing the right torque assembly tool for screws and nuts

185

Torque

Torque2930 lb

f·ft

220 lbf·ft

300 N·m

2011

Serien-No.

Ratio

Max.Output

ModelMax.Input

1 : 16

4000 N

·mDV07.00009

1:164.000Nm

1:186.000Nm

1:228.000Nm

1:28.510.000Nm

1:3913.000Nm

1:17554.000Nm

› Delivery including factory test certi�cate. › The most common input/output torques

on the torque multiplier.

100% quality check

DREMOPLUS ALU FAMILY 1

DVV-40Z, DVV-40ZRS - DVV-540RS

1/2" or 3/4" input square.

Lightweight and slim: High-performance aluminium housing is 30% lighter than a steel one.

Stable, shuttle-impacted gear housing.

Flexible: With detachable Z-form reaction arm, can be optionally retro�tted with L-form reaction arm and adjustable reaction square.

A coating of the tooth �anks consisting of ceramic and te�on enables the gear to be constantly lubricated with a minimum of grease.

A 1", 1.1/2" or 2.1/2" output square with drill hole for impact sockets with safety pin and ring.

A Z-form forged reaction arm of chrome vanadium steel absorbs any countering force that arises. Optional: L-form reaction arm on request.

Overload safety mechanism: Non-destructive overload safety mechanism - Slipper - �led as a patent. Triggers overload at 10% and again clicks into place. Clockwise and anti-clockwise.

Convenient: Integrated RS anti-wind-up ratchet for safe working. Bi-directional (apart from model DVV-40Z).

Low backlash, 2-stage planet gear for a long service life.

186


B

A

a

Q

Cmin.

Cmax.

DVV-40Z

DVV-40ZRS

DVV-40Z & DVV-40ZRS TORQUE MULTIPLIER DREMOPLUS ALU4000Nm / 2930lbf·ft

Particularly suitable for: › Machinery and plant engineering. › Cable cars, lifts and masts. › Heavy industry, construction sites. › Bridge construction. › Ship building, aircraft and railway construction. › Re�neries, plastics industry. › Power plants of all kinds.

Features: › Mechanical hand torque multiplier for controlled screw tightening.

and unloosening screw connections. › With a two-stage planet gear. › High-performance aluminium housing. › Torque multiplication ratio: 1:16. › DVV-40ZRS model with anti-wind-up ratchet (RS). › With non-destructive Slipper overload safety mechanism .

for gear protection - clockwise and anti-clockwise. › Z-form, o�set reaction arm depending on model made of Chrome Vanadium steel. › Can be optionally retro�tted with L-form straight reaction arm -

with adjustable reaction arm - of lightweight metal. › Guaranteed accuracy: Better than +/- 3% tolerance. › For operation in combination with a torque wrench. › 2 models for a maximum load at around a maximum 4000Nm. › Output square drive with a drill hole for sockets or

impact sockets with safety pin and ring.

Scope of delivery: › Torque Multiplier DREMOPLUS ALU. › With Z-form o�set reaction arm. › Delivery in sturdy shipping case with foam insert. › Factory test certi�cate and setting table. › Detailed technical information is available on request

OPTIONAL ACCESSORIES:

Code No. < max. Nm Output

< max.lbf·ft Output

g Q „ C a

„ D A B Cmin Cmax Dmin Dmax ; max.

Nm Input$

; max. lbf·ft Input$

0

2653087 DVV-40Z 4000 2930 1:16 1/2 1 88 212 71 136 250 256 300 220 5.42653109 DVV-40ZRS 4000 2930 1:16 1/2 1 88 227 71 136 264 270 310 230 5.7

Code No. Description A B Cmin Cmax 0

2653184 RL-DVV40 Reaction arm L-form straight for DVV40, 1“ 88 212 86 234 1.7

187

B

A

a

Q

Cmin.

Cmax.

DVV-60ZRS - DVV-130ZRS TORQUE MULTIPLIER DREMOPLUS ALU6000-13000Nm / 4400-9530lbf·ft

Particularly suitable for: › Machinery and plant engineering. › Cable cars, lifts and masts. › Heavy industry, construction sites. › Bridge construction. › Ship building, aircraft and railway construction. › Re�neries, plastics industry. › Power plants of all kinds.

Features: › Mechanical hand torque multiplier for controlled screw

tightening and unloosening screw connections. › With a two-stage planet gear. › High-performance aluminium housing. › Torque multiplication ratio: 1:18, 1:22, 1:28.5, 1:39. › All models with anti-wind-up ratchet (RS). › With non-destructive Slipper overload safety mechanism

for gear protection - clockwise and anticlockwise. › Z-form, o�set reaction arm depending on model made of Chrome Vanadium steel. › Can be optionally retro�tted with L-form straight reaction arm

- with adjustable reaction arm - of lightweight metal. › Guaranteed accuracy: Better than +/- 3% tolerance. › For operation in combination with a torque wrench. › 4 models for maximum load in the range between maximum 6000Nm and maximum 13000Nm. › Output square drive with a drill hole for sockets or

impact sockets with safety pin and ring.

Scope of delivery: › Torque Multiplier DREMOPLUS ALU › With Z-form o�set reaction arm › Delivery in sturdy shipping case with foam insert › Factory test certi�cate and setting table › Detailed technical information is available on request




g Q „ C a


Nm Input$


0

2653117 DVV-60ZRS 6000 4400 1:18 3/4 1.1/2 102 257 110 190 316 324 400 300 10.52653125 DVV-80ZRS 8000 5870 1:22 3/4 1.1/2 128 277 110 190 338 342 420 310 13.42653133 DVV-100ZRS 10000 7330 1:28,5 3/4 1.1/2 142 292 120 216 350 356 410 305 13.92653141 DVV-130ZRS 13000 9530 1:39 3/4 1.1/2 175 306 (126) (229) (372) (379) 380 280 20.9


2654091 RL-DVV60-80 Reaction arm L-form straight for DVV60-80, 1.1/2“ 102/128 256,2/276,5 120/120 315/315 4.0

188


DVV-540RS TORQUE MULTIPLIER DREMOPLUS ALU54000Nm / 40330lbf·ft

Particularly suitable for: › Heavy industry. › Oil industry. › Petrochemicals.

Features: › Mechanical hand torque multiplier for controlled screw tightening and

unloosening screw connections. › With a three-stage planet gear. › High-performance aluminium housing. › Chrome Vanadium steel reaction arm. › Multiplication at the ratio of 1:175. › With anti-wind-up ratchet (RS). › With non-destructive Slipper overload safety mechanism

for gear protection - clockwise and anti-clockwise. › With �xture for welding on a reaction arm (optional). › Guaranteed accuracy: Better than +/- 3% tolerance. › For operation in combination with a torque wrench. › 1 model for a maximum load of around a maximum 54000Nm. › Output square drive with a drill hole - for sockets or impact sockets with a safety

pin and ring.

Scope of delivery: › Torque Multiplier DREMOPLUS ALU. › Delivery in a sturdy crate on pallet. › Setting table. › Detailed technical information is available on request.

SPECIAL REACTION ARMS CAN BE OBTAINED ON REQUEST INCLUDING

TECHNICAL ADVICE.

› Just turn to us - We would be glad to tender any advice. › Any problems you have represent our assignments!



g Q „ C a

„ D A B ; max.

Nm Input$


0

2653168 DVV-540RS 54000 40330 1:175 3/4 2.1/2 270 415 380 280 64.5

189

Torque

Torque2930 lb

f·ft

220 lbf·ft

300 N·m

2011

Serien-No.

Ratio

Max.Output

ModelMax.Input

1 : 16

4000 N

·mDV07.00009


DVI-20L/Z AND DVI-28L/Z

Lightweight: High-performance

aluminium housing is 30 %

lighter than a steel one.

A Z-form forged reaction arm of

chrome-vanadium steel absorbs

any countering force that arises.

DVI-20Z and DVI-28Z › Reaction arm Z-form o�set › �x integrated

DVI-20L and DVI-28L › Reaction arm L-form with adjustable

reaction square drive › �x integrated

3/4" input square

Low backlash, single-stage

planet gear for a long

service life

Output square 1" with drill

hole for impact sockets with

safety pin and ring

Overload safety mechanism

achieved from a classic

shearing square

› Delivery including factory test certi�cate › The most common INPUT/OUTPUT torques

on the torque multiplier

100% quality check

1:4 2.000 N-M

1:4 2.000 N-M

1:5,5 2.000 N-M

1:5,5 2.000 N-M

190


DVI-28Z

DVI-28L

DVI-20L/Z & DVI-28L/Z TORQUE MULTIPLIER DREMOPLUS ALU2000-2800Nm / 1500-2050lbf·ft

Particularly suitable for: › Industry, construction sites, car and truck garages, agricultural technology, construction machinery. › Bridge, aircraft and railway construction, ship building, re�neries. › Machinery and plant engineering, maintenance.

Features: › Mechanical hand torque multiplier for controlled screw tightening

and unloosening screw connections. › With a single-stage planet gear. › High-performance aluminium housing. › Multiplication at the ratio of 1:4, 1:5.5. › Guaranteed accuracy: Better than +/- 3% tolerance. › For operation in combination with a torque wrench. › 2 models for maximum load in the range between maximum 2000Nm and 2800Nm. › Z model: with Z-form, o�set reaction arm of Chrome Vanadium steel. › L model: with L-form straight reaction arm - with adjustable reaction square - of lightweight metal. › Output square with drill hole for impact sockets with safety pin and ring.

Scope of delivery: › Torque Multiplier DREMOPLUS ALU. › With �rmly integrated reaction arm of an Z- or L-form depending on model. › Delivery in sturdy shipping case with foam insert. › Factory test certi�cate and setting table. › Detailed technical information

is available on request.




g Reaction arm Q „ C a

„ D A B Cmin Cmax ; max.

Nm Input$


0

2653265 DVI-20Z 2000 1500 1:4 o�set 3/4 1 88 131 100 150 580 430 2.92653273 DVI-28Z 2800 2050 1:5,5 o�set 3/4 1 106 146 100 150 550 410 3.92653249 DVI-20L 2000 1500 1:4 straight 3/4 1 88 131 73 152 580 430 3.02653257 DVI-28L 2800 2050 1:5,5 straight 3/4 1 106 146 83 199 550 410 4.1

Code No. Description 0

2653303 RL-DVI20 Reaction arm L-form straight for DVI20, 1“ 1.22653338 RL-DVI28 Reaction arm L-form straight for DVI28, 1“ 1.7

191

Torque

Torque2930 lb

f·ft

220 lbf·ft

300 N·m

2011

Serien-No.

Ratio

Max.Output

ModelMax.Input

1 : 16

4000 N

·mDV07.00009


DVV-13Z

1/2" input square.

Low backlash, single-stage planet

gear for a long service life.

Flexible: With detachable Z-form

reaction arm; can be optionally

retro�tted with long reaction

arm incorporating an adjustable

reaction square (L-form) of

lightweight metal.

Lightweight: High-performance aluminium housing is 30% lighter than a steel one.

Output square 3/4" with drill

hole for impact sockets with

safety pin and ring.

The GEDORE maintenance service promoting service life and safety

› Regular maintenance can considerably lengthen the service life of your GEDORE torque multiplier and also contribute to your safety. › Maintenance involves our quali�ed personnel examining the individual components, testing their

functional precision and verifying the factory certi�cate. › In such an instance, we would willingly draft an estimate for you. › We will, of course, continue to support you should you have any questions on and problems with the

former DREMOPLUS models - just get in touch with us ! › Should a guarantee case arise - then either hand the appliance to your dealer or send it directly to

your nearest Gedore agency.

› Delivery including factory test certi�cate › The most common input/output torques

on the torque multiplier.

100% quality check

Reaction arm: Forged reaction

arm absorbs any counter force

arising.

192


DVV-13ZG

DVV-13Z

DVV-13Z TORQUE MULTIPLIER DREMOPLUS ALU1300Nm / 950lbf·ft

Particularly suitable for: › Industry, construction sites, car and truck garages, agricultural technology. › Bridge, aircraft and railway construction, ship building, re�neries. › Machinery and plant engineering, maintenance.

Features: › Mechanical hand torque multiplier for controlled screw tightening

and unloosening screw connections. › With a single-stage planet gear. › High-performance aluminium housing. › With Z-form o�set reaction arm of Chrome Vanadium steel. › Can be optionally retro�tted with L-form straight reaction arm – with adjustable reaction arm

– of lightweight metal. › Multiplication at the ratio of 1:5. › Guaranteed accuracy: Better than +/- 3% tolerance. › For operation in combination with a torque wrench. › 1 model for a maximum load of around a maximum 1300Nm. › Also available as set (No. DVV-13ZG) with three di�erent impact sockets – sizes 27, 30, 32mm. › Output square with drill hole for impact sockets with safety pin and ring.

Scope of delivery: › Torque Multiplier DREMOPLUS ALU. › With Z-form o�set reaction arm. › Delivery in sturdy shipping case with foam insert. › Factory test certi�cate and setting table. › Detailed technical information is available on request.

DVV-13Z

OPTIONAL ACCESSORIES



g Q „ C a


Nm Input$


0

2653370 DVV-13Z 1300 950 1:5 1/2 3/4 80 133 56 95 165 173 270 200 1.9


2653400 RL-DVV13 Reaction arm L-form straight for DVV-13, 3/4“ 80 133 60 159 0.800

193

PULLERS

194

PULLERS

UNIVERSAL PULLERS

197

NUT SPLITTERS

200

EXTRACTOR SETS

202

HSP SPINDLES

199

STUD EXTRACTORS

200

PULLER KITS

203

SAFETY COVER

200

SPECIAL PULLERS

201

PEGBOARD KITS

204

196

PULLERS

> >= >

YOUR PATH TO

THE RIGHT PULLERA How can the component to be extracted be gripped? B Is a support possible either externally or internally? C Which clamping spread/reach has to be obtained?

› The component to be extracted can only be gripped externally. › The centre axle is for supporting purposes.

› The component to be extracted can only be gripped internally. › Centre axle supporting is not possible.

The ball bearing to be pulled is �tted on a shaft and in a housing and, as such, can neither be internally or externally gripped.

› Automotive tool for: › Ball joints. › Oil �lters /cartridges. › Steering wheel. › Springs. › Wheel hubs etc.

› The component to be extracted is well set into, thus ruling out the use of pulling legs. › The centre axle is for supporting purposes.

› Nut splitters. › Stud extractors.

› Flange separators. › Threaded inserts.

1. EXTERNAL PULLING 2. INTERNAL PULLING

3. BALL BEARING EXTRACTION 4. EXTRACTION USING A SPECIAL- PURPOSE TOOL

› Supporting possible outside of the component.

› No support possible - thus the use of extracting aids.

› Centre axle supporting is possible.

› Supporting possible outside of the component.

max. 580

max

. 200

*

max

. 200

*

max

. 400

*40/120 - 140/440

max. 580 5-250

5 - 160 5 - 160

max

. 500

*

60 - 640

max

. 85

20 - 32

SAFETY NOTES 201/238

FOR PULLERS

Code No Running Depth Max. Opening 0

040150 8220-10 105 110 1.20040180 8220-20 160 180 3.10040210 8220-30 210 280 8.50040160 8220-10L 200 110 1.80040190 8220-20L 310 180 4.50040220 8220-30L 410 280 11.60

8220-20

8220-20HSP

Code No y 0

040170 8220-10P 151 0.900040200 8220-20P 220 2.0040230 8220-30P 308 5.0


040460 8220-20HSP1 Puller & Spindle 90 180 3.6040470 8220-30HSP3 Puller & Spindle 100 280 9.9040480 8220-20L HSP1 Puller & Spindle 90 180 5.1040490 8220-30L HSP3 Puller & Spindle 100 280 13.1

› For the safe and fast removal of discs, pulleys, wheels, ball bearings etc. › Strong drop forged design. › Reversible hooks permit use as an internal or external puller. › Available in standard length or with extensions for extra length.


040427 8562-1 50 60 0.20040428 8562-2 70 70 0.22


040417 8563-1 55 60 0.31

8220P

197

8220 TWIN GRIP PULLERS

Universal Pullers

› For removing small parts such as battery terminals, pulleys, wheels, ball bearings etc.


› For removing small parts such as battery terminals, pulleys, wheels, ball bearings etc.

8563 TRIPLE GRIP PULLER


040010 8564-2 100 110 1.0040030 8564-3 140 150 1.9040050 8564-4 200 200 2.3040440 8564-4 HSPIL Puller & Spindle 105 200 3.7


040020 8565-2 80 120 1.3040040 8565-3 140 160 2.5040060 8565-4 200 220 4.0040450 8564-4 HSPIL Puller & Spindle 105 220 4.6


040070 8566-1 300 300 9.8040080 8566-2 400 400 10.8040495 8566-1 HSP3 Puller & Spindle 105 300 10.1040500 8566-2 HSP3 Puller & Spindle 110 370 11.1


040090 8567-1 400 350 11.9040100 8567-2 400 420 13.0040505 8567-1 HSP3 Puller & Spindle 110 345 12.1040510 8567-2 HSP3 Puller & Spindle 110 350 13.3


040110 8568-1 100 150 0.800040130 8568-2 140 200 1.9


040120 8569-1 80 150 1.1040140 8569-2 140 200 2.7

198

PULLERS


8565 TRIPLE GRIP PULLERS





› Suitable for industrial purposes and heavy agricultural as well as construction machines.

› Heavy duty model for the removal of discs, pulleys, wheels, ball bearings etc.



8006190 1.15/1 140 130 1.2

8006350 1.15/2 210 200 3.3

Code No Force Capacity Puller Ref. 0

040350 HSP1L 6-ton - Twin Grip10-ton - Triple Grip

8564-48565-4

1.30

040360 HSP1 6-ton - Twin Grip 8220-208220-20L

1.20

040400 HSP3 8-ton - Twin Grip12-ton - Twin Grip15-ton - Triple Grip

8220-308220-30L8566-18566-28567-18567-2

3.30

1.15 TRIPLE GRIP PULLERS

HSP GREASE HYDRAULIC PRESSURE SPINDLES

› The grease hydraulic pressure spindle has been designed for controlled and safe pulling work, and is set up for a pressure of up to 15t.

199

2

5 6

43Hydraulic bolt

Grub screw

Hydraulic spindle

Tip

Ball Ø 9/16“ or 5/8“

Adjusting cap nut

1

HSP GREASE HYDRAULIC PRESSURE SPINDLEThe grease hydraulic pressure spindle has been designed for controlled and safe extraction forces of up to 15t.

› Before using, check whether the pressure spindle is screwed far enough out of the cap, so that the pressure pad is in the initial position in the hydraulic cylinder. › Unscrew the cap from the spindle body. First slacken o� the grub screw. › Screw the spindle body into the crossbeam of the puller from below until the body protrudes

approximately 60mm from the crossbeam. › Screw the cap onto the spindle body until the stop, and then �x it in position by turning in

the grub screw.

› Place the puller into position and pre-tension the spindle body using a size 32mm or 41mm wrench. › Screw the pressure spindle size 12mm or 17mm into the cap. The hydraulic process will come into

play. The workpiece that has been loosened by the hydraulic force may be pulled o� completely by turning the spindle body with the 32mm or 41mm cap. › After use, the pressure spindle (size 12mm or 17mm) is turned back into its initial position and the

pressure pad is pushed into the hydraulic cylinder.

Preperation for use: Preperation for use:


Code No 0

1868195 5.10 1.5Code No for nuts $ max. t 0

040790 1.26/1 7-22 mm, M4-M14 12 5.0 0.80040870 1.26/2 22-36 mm, M14-M24 12 13.0 3.40

Code No Ø-Stud 0

041010 8600-1 4-10 0.290041020 8600-2 8-25 0.570

Code No C p $ 0

8012750 1.30/0 5-8 M10 10 0.128012830 1.30/1 8-12 M10 10 0.128012910 1.30/2 12-15 M10 10 0.138013130 1.30/3 15-19 M10 14 0.178013480 1.30/4 19-25 M10 14 0.208013560 1.30/4A 25-30 M10 14 0.308013640 1.30/5 30-35 M10 14 0.408013720 1.30/6 35-45 M14 x 1,5 17 0.65

200

PULLERS

Special Tools

5.10 SAFETY COVER

› At pulling forces of 18t, these PVC safety covers provide maximum active safety protection from suddenly detaching ball bearings, driving pinions or small parts. The safety covers are extremely �exible, making them suitable for all applications. › Dimensions 510 x 915mm. › Double-ply welded = double safety (total thickness at 0.5mm = 1.0mm). › Tear strength: longitudinal 23N/mm2 - lateral 21N/mm2.

› Two straps for variable adjustment. › Press stud fasteners for added safety - no �apping ends. › UV resistant. › Temperature resistant at -25 °C to +50 °C. › Supplied in a carry bag which guarantees a long service life.

1.26/1 HYD

1.26/2 HYD

1.26/HYD NUT SPLITTERShydraulic

› With strong chisel, additionally induction hardened. › At the cutting edge for breakage resistance. › The chamfer at the chisel's edge improves the

splitting e�ect and prevents breakage. › With smooth chisel function.

› Channel walls rolled, thus mirror-smooth and wear resistant. › For nuts up to property class 10. › Chisel replaceable. › For splitting jammed or stripped nuts without .

damaging the bolt thread.

8600 STUD EXTRACTORS

› For inserting and removing studs. › Suitable for extremely short stud ends.

1.30/N INTERNAL EXTRACTORSwith reinforced shoulder

› For extremely tightly packed ball bearings,bearing races, bushes, shaft seals and circlips. › The shoulder of the shell jaw must be applied behind the bearing.

201

Code No $ p 0

8016580 1.36 / 1 27 M10 0.758016660 1.36 / 2 32 M14 x 1,5 1.65

Code No A O for puller C 0

8019680 1.40/0 5-60 1.38/0 M10 1.108019760 1.40/1 12-75 1.38/1 M10 3.608019840 1.40/2 22-115 1.38/2 M14x1,5 2.308019920 1.40/3 30-155 1.38/3 M18x1,5 4.40

Code No For separator a b $ 0

8017550 1.38/0 1.40/0 40-120 125 17 1.08017630 1.38/1 1.40/1 60-165 180 19 1.18017710 1.38/2 1.40/2 70-215 195 22 3.48017980 1.38/3 1.40/3 90-300 205 27 6.5

Code No Leg length up to Clamping reach $ 0

8028240 1.67/1 135 35-90 17 0.90

1.36 SUPPORT BRACE

› Operation: The counter-support brace is placed on the housing and the spindle screwed onto the spindle of the internal extractor. The toggle is held �rmly, and the bearing extracted by tightening the nut.

C

A

1.40 SEPARATORS

› For removing taper roller and ball bearings, inner bearing races, and other tightly-seated or thin-walled parts. › Operation: The sharp edges of the separator blades are pressed behind

the part and it is then withdrawn using the 1.38 puller. › To avoid damage to delicate parts, the �at surfaces of the separator

are used. › This produces a large support surface that prevents deformation.

c

d

1.38 SEPARATOR PULLERS

› These separator pullers are used together with the bearing separators 1.40. › The tension bolts are screwed into the threaded

holes in the bearing separators.

1.67 STEERING WHEEL PULLERfor cars

› Contains 1 pair of short legs, 1 pair of long legs, and a protective cap for the thread of the steering column.

202

PULLERS

1.85/1 PROFESSIONAL PLASTIC BEARING INSTALLATION SET

› Sturdy plastic bearing installation set. › Impact resistant plastic is light but as robust

as metal variants. › This set guarantees that the installed bearings

will not su�er the damage that might have

Code No. Contents 0

1120778 1.85/1 33 impact rings, 10-50mm for external Ø 26-110mm3 aluminium impact sleeves1 recoil-free bodywork hammer with nylon heads (1.2kg)

5.2

1101-1.29/3K BALL BEARING EXTRACTOR SET

Code No. Contents For ball bearing No. 0

2964392 1101-1.29/3K 4 Heads with spindle no. 1.29/1-1.29/57 Heads with spindle no. 1.29/10-1.29/451 Handle no. 1.29/0

6000 6001 6002 6003 6004 6005 6006 6007 6008 6009 6010 6011 6012 6200 6201 6202 6203 6204 6205 6206 6207 6208 6209 6210 6211 6212 6213 6300 6301 6302 6303 6304 6305 6306 6307 6308 6309 6310 6311 6403 6404 6405 6406 6407

5.8

occured when working ‘metal to metal’. › Ensures no deformations of the bearing

housings, sealing rings or shafts.

› Ball bearing extractor set for more than 40 ball bearings. › For removing ball bearings that are both

on a shaft and in a housing. › Non-destructive removal of deep-groove ball

bearings without dismantling the shaft; no necessity to drill open the bearing cage (no chippings).

› With Check-Tool insert. › Insert for use in drawers with minimum

dimensions 340 x 260 x 60mm. › In GEDORE i-BOXX® 72 No. 1101 L. › Dimensions: 367 x 316 x 72mm.

Code No 0

6759890 8551-88 Bolt Extractor Set 0.724Sizes 1 2 3 4 5 6 7 8

Code No Clamping height Fork Depth O 0

8030810 1.73/1 65 24 23 0.730

8551 BOLT EXTRACTOR SET

› Made from Chrome Vanadium steel-35HRC. › In sturdy plastic case.

Operation › Drill a central hole into the briken bolt. › Turn the bolt extractor to the left into the

hole until it grips and removes the bolt. › Always use the maxiumum extractor

size.

1.73 UNIVERSAL BALL JOINT PULLER

› For removing ball joints on cars.

NEW

203

Puller Kits

Code No. Contents 0

2838362 1100-1.04 L-Boxx® 136 no. 1100L+ Assortment no. 1100 CT2-1.04

6.3

1101-1.29/3K BALL BEARING EXTRACTOR SET

1100-1.04 UNIVERSAL PULLER SETin L-BOXX® 136

› Maximum capacity up to 5t. › 2- and 3-arm cross-beam. › With rigid and slim legs and extensions. › Extra-slim pulling legs for cramped spaces are attached for

self-mounting. › The forged leg feet are very slim particularly suitable for

barely accessible places.

› 12 di�erent pullers can be combined. › External Ø up to 130mm, internal Ø up to 170mm with a

200mm clamping reach. › 1100 CT2-1.04 to retro�t existing L-BOXX®es 136. › As tools are fully sunk in the foam, the equipped insert

can be stacked.

1.07/K PULLER SETwith 9 legs

› In plastic case. › Dimensions: 120 x 250mm.

Code No. Contents a b max.t A $ c d e 0

8117340 1.07/K 2-arm Cross Piece3-arm Cross Piece3 x Pulling Hooks - 100mm3 x Pulling Hooks - 200mm3 x Slim Pattern Pulling Hooks - 250mm

130 100 / 200 / 250 2.5 M 14x1,5 x 140 17 27 7.5 3.7 5.8

1.31 INTERNAL EXTRACTOR SET

› For extremely tightly packed ball bearings, bearing races, bushes, shaft seals and circlips.

Code No. Contents 0

8014610 1.31/1 6 internal extractors 12-46mm, No. 1.30/2 - /62 counter-support braces No. 1.36/1 - /2

6.4

204

PULLERS

2.10 CAR WORKSHOP KIT

› Clearly arranged modular system on pegboard.

2.20 TRUCK WORKSHOP KIT

2.30 INDUSTRIAL PULLER KIT

› For the assembly of 1.06 and 1.07 pullers. › Clearly arranged modular system on pegboard.

2.40 CONSTRUCTION MACHINE KIT

› Clearly arranged modular system on pegboard.

› For the assembly of 1.14 and 1.15 pullers. › Clearly arranged modular system on pegboard.

Code No. Contents 0

1088696 2.10PKW 2-arm Cross Piece - 140mm3-arm Cross Piece - 140mm3 x Pulling Hooks - 100mm3 x Slim Pattern Pulling Hooks - 100mm2-arm Battery Terminal PullerNut SplitterStud ExtractorDismantling & Assembly ForkUniversal Ball Joint PullerOil Filter Hook

13.8Code No. Contents 0

1088718 2.20LKW 2-arm Cross Piece - 260mm3-arm Cross Piece - 260mm3 x Pulling Hooks - 100mm3 x Pulling Hooks - 300mm3 x Slim Pattern Pulling Hooks - 220mmSpindleHydraulic Pressure SpindleBearing Separator

25.0

Code No. Contents 0

1393014 2.30 4 x 2-arm cross pieces 140 180 220 260mm4 x 3-arm cross pieces 140 180 220 260mm2 x SpindlesHydraulic Pressure Spindle6 x Pulling Hooks


1393030 2.40 2 x 2-arm Heads2 x 3-arm Heads3 x Pulling Hooks - 210mm3 x Pulling Hooks - 260mm3 x Pulling Hooks - 390mm2 x SpindlesHydraulic Pressure Spindle

24.9

205

= > > >

SAFETY NOTESPULLERS

› Read the operating instructions! › Use only original spare parts and accessories for your Gedore puller. Never use worn, modi�ed or

defective spare parts or accessories. › Wear goggles and protective clothing when working. For added safety, use the Gedore safety

cover 5.10!

› Before pulling, ensure that the legs are in contact with the part to be pulled and are �rmly tightened so that the spindle operates centrally along the axis of the puller. › Attention! When using a puller, forces of up to several tons are generated! Take care to ensure

that the puller is correctly positioned and is vertical to the component being pulled. › Do not use electric or pneumatic power or percussion drivers.

INDUSTRIAL KIT11 pieces

CAR WORKSHOP KIT15 pieces

› Clearly arranged modular system on pegboard. › Clearly arranged modular system on pegboard.

Code No. Contents 0

634840 Industrial Puller Kit (7-Piece)

8220-20 Universal Twin Grip Puller8220-20P Extension8565-4 Triple Grip PullerHSP 1 Hydraulic Pressure Spindle8569-2 Universal Triple Grip Puller8600-2 Stud Extractor248 ST Recoil Free Hammer1450S Tool Panel (Including Hooks)


634859 Car Workshop Puller Kit (11-Piece)

8220-10 Universal Twin Grip Puller8220-10P Extensions8562-2 Battery Terminal Puller8565-2 Triple Grip Puller8569-1 Universal Triple Grip Puller8600-2 Stud Extractor1.38-0 Separator Puller1.40-0 Bearing Separator1.73-1 Ball Joint Puller1.75-1 Oil Filter Hook248 ST Recoil Free Hammer1450S Tool Panel (Including Hooks)

13.6

NON-SPARKING TOOLS

206

NON SPARKING

TOOLS

SPANNERS / SETS

208

(1/4”) SOCKET SET

210

ADJUSTABLE WRENCH

211

(1/2”) SOCKETS

209

SCREWDRIVER SET

210

COMBINATION PLIERS

211


209

PIPE WRENCH

211

SIDE CUTTERS

211

208

NON-SPARKING TOOLS

WHY THE NEED FOR NON-SPARKING TOOLS

› Made either from proven, low-sparking special bronze and copper/beryllium alloys or from other non-spark inducing materials. › The spanners are cast and not forged for your own safety. › Corrosion resistant, even against salt water. › Copper/beryllium tools are non-magnetic. › Non-sparking tools are not as hard as conventional ones and must be used

with care.

› Using non-sparking tools must not be the only protective measure taken in aeas of �re or explosion risk. › It would be more accurate to refer to ‘low spark’ since ignitable sparks cannot

be 100% prevented with the use of non-sparking tools.

The recommendation is to use GEDORE non-sparking tools in all areas where combustible or easily ignitable vapours, liquids and dusts are; as well as where there is potential for �re or explosion caused by sparks.

Non-Sparking Combination Spanners

GED0130 COMBINATION SPANNERS

› With same size on each end. › Bi-hexagon ring.

Code No. ! y 0

2510855 GED0130006S 6 130 0.0502510847 GED0130007S 7 130 0.0552510839 GED0130008S 8 135 0.0 552510820 GED0130009S 9 150 0.0 952509148 GED0130010S 10 150 0.0852509121 GED0130011S 11 150 0.0 902509113 GED0130012S 12 190 0.1702509105 GED0130013S 13 190 0. 1652509091 GED0130014S 14 190 0. 1602509083 GED0130015S 15 210 0.2302509075 GED0130016S 16 210 0.2302509067 GED0130017S 17 210 0.2202509040 GED0130018S 18 230 0.330

Code No. ! y 0

2509032 GED0130019S 19 230 0.3302509024 GED0130020S 20 230 0.3252509016 GED0130021S 21 250 0.3602509008 GED0130022S 22 250 0.3552508990 GED0130023S 23 250 0.3502508982 GED0130024S 24 270 0.5002508974 GED0130025S 25 270 0.4752508966 GED0130026S 26 270 0.4702508958 GED0130027S 27 280 0.6652508923 GED0130028S 28 280 0.6802508915 GED0130029S 29 280 0.6302508907 GED0130030S 30 300 0.7302508893 GED0130032S 32 300 0.650

GED0130 COMBINATION SPANNER SETS

› Sets made up of the most popular sizes.

Code No. Contents 0

2493551 GED0130003S-11 Pieces 8 10 11 12 13 14 16 17 18 19 22 2.202493578 GED0130001S-12 Pieces 10 11 12 13 14 17 19 22 24 27 30 32 4.10

209

Non-Sparking Sockets & Accessories 1/2“

GED035 HEXAGON SOCKETS 1/2“

› Hand operated.

Code No. ! y 0


Code No. ! y 0


GED0360 REVERSIBLE RATCHET 1/2

GED042 EXTENSIONS 1/2

GED410 SWIVEL HANDLES 1/2

› For hand operated sockets. › For hand operated sockets.

› For hand operated sockets.

Code No. y 0

2513684 GED0360012C 250 0.590

Code No. y 0

2506335 GED0420002S 100 0.1802506270 GED0421434S 200 0.3152506319 GED0420121S 250 0.360

Code No. y 0

2507927 GED0410013S 250 5602507897 GED0410016S 300 920

1B (AF) COMBINATION SPANNERS 9

210

NON-SPARKING TOOLS

GED0400 SLIDING T-BAR 1/2


GED0400 UNIVERSAL JOINT 1/2

GED0430 SOCKET SET 1/2

› In plastic case. › Picture may di�er from actual product.

GED080 SCREWDRIVER SET5 pieces

› Picture may di�er from actual product.

Code No y 0

2511886 GED0400114S 250 0.450


Code No y 0

2514788 GED0400118S 70 0.135

Code No. Contents 02503239 GED0430002S Reversible Ratchet 1/2”

Extension 1/2” 150mmSliding T-bar 1/2” 320mmSwivel handle 1/2” 380mmSockets: 10 11 12 13 14 15 16 17 18 19 2 0 21 22 23 24 25 26 27 28 29 30 32mm

4.10Code No. Contents 02499061 GED0800002C 4,5x100mm

6x100mm 6x150mm 8x150mm PH1 PH2

0.515

211

Code No y 0

2522659 GED0662650C 190 0.290

GED053 PIPE WRENCH

› American pattern.

GED048 ADJUSTABLE WRENCHES

GED060 COMBINATION PLIERS

GED066 POWER SIDE CUTTERS

› With two-component handle.

Non-Sparking Wrenches/Pliers

Code No y 0

2514753 GED0602000C 200 0.425

› With two-component handle.

Code No y 0

2517310 GED0530385S 385 1.37Code No y 0

2503166 GED0482000C 200 0.2002503158 GED0482500C 250 0.4002503131 GED0483000C 300 0.700

APPRENTICE TOOLKITS

ELECTRICIAN‘S & REFRIGERATION MECHANIC‘S

218

APPRENTICE

TOOLKITS

CONSTRUCTION MACHINERY

214

MECHANIC‘S / AUTOMOTIVE

216-217

APPRENTICE TRUNK

219

214

APPRENTICE TOOLKITS

CONSTRUCTION MACHINERY TOOLKITFor construction apprentices and tradesman.

261 pieces

b

c

d

e

1525 Tool Trolley

1425 Tool Chest

Foam Inserts 1525-41-1B 1525-41-400 1525-41-403 1525-41-4550 1525-41-D321525-41-8601 1525-27-621525-27-PH 1525-27-PL

62-150, 450mm Adjustable Wrenchs

145-10CUniversal Pliers

137-250Grip Pliers

8000-A2Circlip Pliers

8000-J2Circlip Pliers

8250-200 JCCombination Pliers

8132-200 JCTelephone Pliers

8316-200 JCSide Cutters

8531-250Tin Snips

8601-500, 900Ball Pein Hammers

248-STReccoil Free Hammer

9270-02Rubber Mallet

95-125, 150, 175Flat Chisel

116APin Punch Set

4550-20Torque Wrench

702-21MFeeler Gauge Set

9300.00Key File Set

9534.05Tape Measure - 5m

Scriber-MS/ST-190mm

Digital Multimeter

Code No. 0

668119 Construction Machinery Toolkit 145.53

215

Caliper-Vernier -150x0.02mm

File Thread Restorer

403Hacksaw

3081L-Handle

3090-125, 250Extensions

3019Adapter

3095Universal Joint

3087Sliding T-bar

3093-Z94Reversible Ratchet

1995Universal Pliers

1990-75,125,250Extensions

1985Speed Brace

1987Sldiing T-bar

1997-375Swivel Handle

1993-U10TReversible Ratchet

3295Universal Joint 3/4”


3287Sliding T-bar

3293-U1Reversible Ratchet

3296Swivel Handle


4179-70Slidng T-bar

4179-80Universal Joint

4190-50Reversible Ratchet

4177 Sockets-4, 4.5, 5, 5.5, 6, 7, 8, 9, 10, 11, 12, 13, 14

D30 Sockets-8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 7/16 AF, 9/16 AF, 7/8 AFC19 Sockets- 8-5/16, 10-3/8, 11, 12, 13-1/2, 14, 15-19/32, 16-5/8, 17, 18-11/16, 19-3/4, 21-13/16, 22, 24-15/16, 26-1., 27-1.1/16, 29-1.1/8, 30-1.3/16, 32-1.1/4

D19 Sockets- 5/16 AF, 3/8 AF, 7/16 AF, 1/2AF, 9/16 AF, 5/8 AF, 11/16 AF, 3/4 AF, 13/16 AF, 7/8 AF, 15/16 AF, 1 AF, 1.1/16 AF, 1.1/8 AF

C32 Sockets-19-3/4, 22-7/8, 24-15/16, 26-1, 27-1.1/16, 29-1.1/8, 30-1.3/16, 32-1.1/4, 33-1.5/16, 38-1.1/2, 41-1.5/8, 46-1.13/16, 50-2

D32 Sockets-1.3/8 AF, 1.7/16 AF, 1.11/16 AF, 1.3/4 AF, 1.7/8 AF

4171 Sockets-T10, T15, T20, T25, T27, T30, T40

4172 Sockets-PZ 0, PZ 1, PZ 2, PZ 3

4178 Sockets-3, 4, 5, 6, 8, 10

4179 Sockets-PH 0, PH 1, PH 2, PH 3

4174 Sockets-E5, E6, E7, E8, E10

ITX19 Sockets-T20, T25, T27, T30, T40, T45, T50

TX19 Sockets-E10, E12

TX30 Sockets-E5, E6, E7, E8

IN19 Sockets-5/16 AF, 3/8 AF, 1/2 AF, 9/16 AF, 5/8 AF

1B Combination Spanners-6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 321.1/4AF, 1.5/16AF, 1.3/8AF, 1.1/2AF, 1.1/8 AF, 1.1/16 AF

1B13A-1/4AF, 5/16AF, 3/8AF, 7/16AF, 1/2AF, 9/16AF, 5/8AF, 11/16AF, 3/4AF, 13/16AF, 7/8AF, 15/16AF, 1AF400 Flare Nut Spanners-17x19, 22x24, 7/16x1/2, 9/16x5/8, 5/16x3/8

42L-9M Long Allen Keys Set-1.5, 2, 2.5, 3, 4, 5, 6, 8, 10

42-9P Allen Keys Set-1/16”, 5/64”, 3/32”, 1/8”, 5/32”, 3/16”, 1/4”, 5/16”, 3/8”2150 3C Screwdriver 4 6.5 10

2160 3C ScrewdriverPH1 PH2 PH3

216

APPRENTICE TOOLKITS

MECHANIC‘S TOOLKIT

95-300 Flat ChiselCode: 86993700 0.5609000.00 VernierCode: 18249100 0.3209534-05 Tape MeasureCode: 22503810 0.200227-350 Pipe WrenchCode: 6453460 1.62Suction-19mmCode: 01201300 0.020SuctionLifter-22mmCode: 01201200 0.020Circuit TesterCode: 01201000 0.040Tyre Pressure GaugeCode: 01201100 0.120400-5M Flare Nut Spanner SetCode: 6340260 0.710INX19 PM-5D Allen Key Socket SetCode: 6179890 1.32

For diesel, forklift, motor, tractor, motorcycle, diesel fuel injection mechanic, and diesel fitter apprentices and tradesmen.

1410 Tool Chest

D19 Sockets- 8, 10, 11, 12, 13, 14, 15, 16, 17, 19, 21, 22, 23, 24, 26, 27, 28, 30, 321B Combination Spanners-6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 24534 Swivel Head Spanners-10, 11, 12, 13, 14, 15, 16, 17, 19

62-200, 300mmAdjustable Wrenches


248-STRecoil Free Hammer

42-88M-2, 2.5, 3, 4, 5, 6, 7, 8, 9, 10Allen Keys Set

42-88P-3/32”, 1/8”, 5/32”, 3/16”, 7/32”, 1/4”, 5/16”, 3/8”Allen Keys Set116APin Punch Set

2160PH1 PH2

21504 5.5 6.5 8 10

8531-250Tin Snips

36/1Oil Filter Wrench

Safety Glasses

10pc Drill Bit Set

Thread Restorer

Flat File-250

Round File-250

Half-Round File-250

100-16Centre Punch

95-175, 200Flat Chisel

Stainless Steel Ruler-300mm

Engineers Square-100mm

Engineer‘s Scriber 190mm


403Hacksaw







137-250Grip Pliers

Oil Can-300

1993-Z94Reversible Ratchet

1985Feeler Gauge Set

1987Speed Brace


1995Universal Joint

50-20,8mmSpark Plug Socket

54-16mmSpark Plug Socket

Optional Extras

Code No. 0

668036 Mechanic’s Toolkit 41.50

d

217

AUTOMOTIVE ELECTRICIAN‘S TOOLKIT

Code No. 0

668028 Automotive Electrician’s Toolkit 35.50

b

d

95-300 Flat Chisel Code: 86993700 0.40095-200 Flat ChiselCode: 86989900 0.400Junior HacksawCode: 01202100 0.100134-250 Grip PliersCode: 7459950 0.5709000.00 VernierCode:0 0.3209534-05 Tape MeasureCode: 22503810 0.2001985 Speed BraceCode: 6143350 0.58550-20.8mm Spark Plug SocketCode: 6366140 0.11954-16mm Spark Plug SocketCode: 6366220 0.096702-21M Feeler Gauge SetCode: 65479500 0.070D19HMZ Socket SetCode: 6146100 1.9310pc Drill Bit SetCode: 01200000 0.510

1410 Tool Chest

1B Combination Spanners-6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 2244000.00-52 Piece 1/4” Socket Set

Tube Spanner Set-8x9, 10x11, 12x13, 14x15, 16x17, 18x19

26-RS2 To be used with Tube Spanner Set

42-88M Allen Keys Set-2, 2.5, 3, 4, 5, 6, 8, 10

42-88P Allen Keys Set-3/32”, 1/8”, 5/32”, 3/16”, 7/32”, 1/4”, 5/16”, 3/8”

2160PH1 PH2

21504 5.5 6.5 8

116APin Punch Set

100-10, 16Centre Punches

8601-700Ball Pein Hammer

267-40Recoil Free Hammer

Circuit Tester

8132-160 JCTeelphone Pliers



8132AB-160 TLTelephone Pliers


62-200Adjustable Wrench

Heavy Duty Crimping Pliers

8516-250Tin Snips

Wire Stripper

Digital Multimeter

Stainless Steel Ruler-300

9100.00Utility Knife

403Hacksaw

Safety Glasses

Engineer‘s Scriber

Box Wrench Set-8 Piece

Needle File Set-6 Piece

Optional Extras

218

APPRENTICE TOOLKITS

ELECTRICIAN‘S & REFRIGERATIONMECHANIC‘S TOOLKIT

Code No. 0

668001 Electrician’s & Refrigeration Mechanic’s Toolkit

38.50

95-200 Flat ChiselCode: 86989900 0.400Engineers SquareCode: 01200600 0.2209530-0300 Spirit LevelCode: 22503300 0.630227-350 Pipe WrenchCode: 6453460 1.629000.00 VernierCode: 18249100 0.3209534-05 Tape MeasureCode: 22503810 0.2008000-A2 Circlip PliersCode: 67015400 0.1678000-J2 Circlip PliersCode: 67034000 0.146

1410 Tool Chest

1B Combination Spanners-6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 2244000.00-52 Piece 1/4” Socket Set

D19HMZ Socket Set

42-88M Allen Keys Set-2, 2.5, 3, 4, 5, 6, 8, 10

42-88P Allen Keys Set-3/32”, 1/8”, 5/32”, 3/16”, 7/32”, 1/4”, 5/16”, 3/8”

2160PH1 PH2

21504 5.5 6.5 8

116APin Punch Set

100-16Centre Punches

Flat File-250

Round File-250

Half-Round File-250





248-STRecoil Free Hammer


62-200, 300Adjustable Wrenches

Heavy Duty Crimping Pliers

Wire Stripper

Digital Multimeter

Stainless Steel Ruler-300


403Hacksaw

Safety Glasses


Box Wrench Set-8 Piece

137-250Grip Pliers

Optional Extras

Circuit Tester

95-100Flat Chisel

b

d

219

APPRENTICE TRUNK TOOLKIT

Code No. 0

668109 Apprentice Trunk Toolkit 48.63

1460 Tool Trunk

1B 6 ,7, 8, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 32, 34, 36

1B 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 7/8, 15/16, 1, 1.1/16, 1.1/8, 1.3/16, 1.1/4






137-250Grip Pliers


116APin Punch Set

100-16Centre Punches

Flat File-250

4550-20Torque Wrench

403Hacksaw

8601-100Ball Pein Hammers

D32-EMZ3/4“ Socket Set

2160PH1 PH2

21506.5 3-150 4-150 6.5-200

42KL-9M1,5 2 2,5 3 4 5 6 8 10


D306 7 8 9 10 11 12 13 14 15 16 17 18 19 21 223081L-Handle

3090 Extension125mm

3093Z-94Ratchet

1993Z-94Reversible Ratchet

D19 Sockets 8, 10, 11, 12, 13, 14, 15, 16, 17, 19, 21, 22, 23, 24, 26, 27, 28, 30, 32

5/16 AF, 3/8 AF, 7/16 AF, 1/2AF, 9/16 AF, 5/8 AF, 11/16 AF, 3/4 AF, 13/16 AF, 7/8 AF, 15/16 AF, 1 AF, 1.1/16 AF, 1.1/8 AF, 1.3/16 AF, 1.1/4 AF

1997-450Power Bar

1987Sliding T-Bar

1990 Extensions125, 250mm

d

c

e

3/4“ Socket Set

› 4x Sliding trays with high-density foam inserts.

220

APPRENTICE TOOLKITSCUSTOMISED

GEDORE INDIVIDUAL

PRECISE – CUSTOMISED

High-density foam

Plastic references

Why not create your perfect tool assortment to match your

corporate design requests and your process speci�cations.

We look forward to hearing from you!

All assortments are packed in high-density foam inserts or

plastic references and will �t into an appropriate

compartment of the GEDORE tool chests, trolleys or

toolboxes.

Minimum quantities apply.

221

Tidy, uncluttered look and always easily accessible

› Ready to be used straight after delivery: simply unpack and screw on the handle.

› Whether for mobile use or stationary, every tool has its place.

› Modular arrangement systems make daily routine that much easier (no more

scratching for tools)

› Compact tool assortments make for easy tool selection.

› Customised equipment/tool sets in module systems and/or trolleys/benches in

company design/colours.

ADVANTAGES:

› Easy assessment of what tools to buy.

› Spend less time ‘looking for tools’.

› Tidier workplace.

› Easy identi�cation and easy access of the correct tool.

› Easily check whether the toolset is complete.

› Elimination of unnecessary tool purchases – no surplus

tool accumulation.

Custom colour choices

222

ARTISAN TOOLKITS

ARTISAN‘S

TOOLKITS

ELECTRICIANS LIGHT CURRENT 214

GENERAL ARTISAN‘S

227

ELECTRICIANS MEDIUM CURRENT 215

TECHNICIAN‘S RUCKSACK

228

FARMER‘S

226

ELECTRICIAN‘S

229

224

ARTISAN TOOLKITS

ELECTRICIAN‘S LIGHT CURRENT TOOLKIT

Code No. 0

668110 Electrician’s Light Current Toolkit32.20

1410 Tool Chest

1B Combination Spanners-6, 7, 8, 9, 10, 11, 12, 13

62-150Adjustable Wrench

42-88M Allen Keys Set-2, 2.5, 3, 4, 5, 6, 7, 8, 9, 10

60CP-250Adjustable Wrench

21506.5 3-150 4-150 6.5-200

2160PH1 PH2


Junior Hacksaw

137-250Grip Pliers




Universal Panel Key

Digital Multimeter

Wire Stripper

8601-500


403Hacksaw

9930.000LED Torch


225

ELECTRICIAN‘S MEDIUM CURRENT TOOLKIT

1410 Tool Chest

1B Combination Spanners-6, 7, 8, 9, 10, 11, 12, 13

62-150, 300mm Adjustable Wrenches

42-88M Allen Keys Set-2, 2.5, 3, 4, 5, 6, 8, 10

Circuit Voltage Tester

VDE 2133 Nut Drivers6, 7, 8, 9, 10, 11, 12, 13

VDE 2160PH1 PH2

VDE 2170 3.5 4 5.5 6.5


Junior Hacksaw

137-250Girp Pliers

VDE 8132-160 HTelephone Pliers

VDE 8250-200 HCombination Pliers

VDE 8314-140 HSide Pliers

Universal Panel Key

Digital Multimeter

Wire Stripper


9534-05Tape Measure

403Hacksaw

9930.000LED Torch

VDE 4522Cable Knife

Heavy-Duty Crimping Pliers

D19HMZSocket Set

Code No. 0

668113 Electrician’s Medium Current Toolkit32.20

226

ARTISAN TOOLKITS

1335 Tool Box

1B Combination Spanners-6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 2462-300Adjsutable Wrench

42-88M Allen Keys Set-2, 2.5, 3, 4, 5, 6, 7, 8, 9, 10

403Hacksaw

21504 5.5 6.5 8

2160PH1 PH2


Junior Hacksaw

137-250Grip Pliers




Leather Gloves

Digital Multimeter

8531-250Tin Snips


9534-05Tape Measure

Yale Padlock

9930.000LED Torch

Fencing Pliers 8260-300

Flat File-250

Round File-250

Half-Round File-250

50-20.8Spark Plug Socket

95-250Flat Chisel


38-500Tyre Lever

106Chisel and Punch Set

C19TMZ Socket Set 1/2“


227-350Pipe Wrench

FARMER‘S TOOLKIT

Code No. 0

668111 Farmer’s Toolkit32.40

227

1410 Tool Chest

1B Combination Spanners-6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 2462-300Adjustable Wrench

42-88M Allen Keys Set-2, 2.5, 3, 4, 5, 6, 8, 10

8133-180 JCTriple Pliers

21504 5.5 6.5 8

2160PH1 PH2


403HAcksaw

137-250Grip Pliers


8250-200 JCCombiantion Pliers


Flat File-250

Round File-250

Half-Round File-250

8601-700Ball Pein Hammers

9534-05Tape Measure

267-40Recoil Free Hammer

9930.000LED Torch

8531-250Tin Snips

50-20.8Spark Plug Socket

C19HMZ Socket Set 1/2“

227-350Pipe Wrench


Stainless Steel Ruler-300mm


Safety Glasses

Engineers Square

116APin Punch Set

44000.00-52 Piece 1/4” Socket Set

Vernier

95-250Flat Chisel

100-16Centre Punch

GENERAL ARTISAN‘S TOOLKIT

Code No. 0

668112 General Artisan’s Toolkit42.0

228

ARTISAN TOOLKITS

TECHNICIAN‘S RUCKSACK TOOLKIT

Code No. 0

668120 Technician’s Rucksack Toolkit8.61

Gedore Rucksack

No.6 Open-Ended Spanners-6x7, 8x9, 10x11, 12x13, 14x15, 16x17, 18x19, 20x2262-200HAdjustable Wrench

42-7M Allen Keys Set-2, 2.5, 3, 4, 5, 6, 8

21506.5 3-150 4-150 6.5-200

2160PH1 PH2


Leather Gloves




SRC-C19Z-10 Socket Set 1/2“

9930.00LED Torch


229

VDE 8132-200 HTelephone Pliers

VDE 8250-200 HCombination Pliers

VDE 8314-160 HSide Cutters

VDE 8098-160 HStripping Pliers


9534-05Tape Measure

9930.000LED Torch

VDE 4522Cable Knife

VDE 2133 Nut Drivers4 6 8 10 13

ELECTRICIAN‘S TOOLSET

Code No. 0

668122 Electrician’s Toolset6.1

Electrician‘s Toolcase

1B Combination Spanners-8, 10, 13, 17, 19

42-88M Allen Keys Set-2, 2.5, 3, 4, 5, 6, 8, 10

Digital Multimeter

VDE 2160PH1 PH2 PH3

VDE 2170 4 5.5 6.5


137-175Grip Pliers

V62-250Adjustable Wrench

230

ARTISAN TOOLKITS

1425 Tool Chest

1B 6 ,7, 8, 9, 10,11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 32

1B 34, 36, 41, 46, 1. 5/16, 1. 3/8, 1. 7/16, 1. 1/2

1B 1/4, 5/16, 3/8, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1, 1.1/16, 1.1/8, 1.3/16, 1.1/4



8132AB-200 JCTelephone Pliers


145-250Water Pump Pliers

137-250Grip Pliers

225-450Pipe Wrench

62-24“ 600mmAdjustable Wrench

702-20M Feeler Gauge Set 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100

42-9P Allen Keys Set

42-22M 0.7, 0.9, 1.3 , 1.5, 2, 2.5, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 14, 16, 17, 19, 22, 24

21504 5.5 6.5 8

2160PH1 PH2

S8000 External 8000-A2 Straight , 8000-J2 Straight Internal 8000-A21 Angled , 8000-J21 Angled

D19 8, 10,11,12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 23, 24, 26, 27, 28, 30, 32 mm1993Z-94Ratchet

1985Speed Brace

1995Universal Joint

1990-125mmExtension

1990-250mmExtension

1987Sliding T-Bar

36/1Oil Filter Strap Wrench


116APin Punch Set

95-150Flat Chisel

100-12Centre Punch

ARTISAN 1425/5 TOOLCHEST

Code No. 0

663059 Artisan 1425/5 Toolchest35.0

› 4x Drawers with customised high-density foam inserts. › Extra space provided for storing additional tools in 1 empty drawer.

231

CUSTOMISED TRUCKING TOOLKIT

Code No. 0

668123 Customised Trucking Toolkit145.0

1425 Tool Chest +1525 Trolley

1B 6 ,7, 8, 9, 10,11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 32, 36

No.7 6 ,7, 8, 9, 10,11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 32

No.534 10,11, 12, 13, 14, 15, 16, 17, 19




D30HMZ 3/8“Socket Set

145-10CWater Pump Pliers

137-250Grip Pliers

62 200, 300, 375mmAdjustable Wrench

1997 450mmPower Bar

702-20M Feeler Gauge Set 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80, 85, 90, 95, 100D19 8, 10,11,12, 13, 14, 15, 16, 17, 18, 19, 21, 22, 23, 24, 26, 27, 28, 30, 32 mm1993Z-94Ratchet

9534.055M Tape Measure

1995Universal Joint

1990-125, 250mmExtension

1987Sliding T-Bar


403Hacksaw

4430.210 Socket Set1/4“

116APin Punch Set

119-3 , 119-4, 119-5, 119-6, 119-7, 119-8

95-150, 95-200mmFlat Chisel

100-16mmCentre Punch

42KL-9M Allen Keys Set1.5, 2, 2.5, 3, 4, 5, 6, 8, 10, 11, 12, 1442KL-8P 3/64” 1/16” 5/64” 3/32” 7/64” 1/8” 9/64” 5/32”

S8000 External 8000-A2 Straight , 8000-J2 Straight , 8000-A4 Straight Internal 8000-A21 Angled , 8000-J21 Angled, 8000-J4 Straight

ITX19 T20, T25, T27, T30, T40, T45, T50

IN19 5, 6, 7, 8, 9, 10, 12, 14, 17, 19mm

TX19 E10, E11, E12, E14, E16 E18, E20, E24

D19L 10, 27mm


Half Round & Round Files 200mm

267-50mmRecoil free hammer

9250Club Hammer

4611Power Tester 6-24V

9000Vernier

163 / TX TORX® Screwdrivers T6, T7, T8, T9, T10, T15 T20, T25, T27, T30, T40

9175.060Scraper

150MS 1.2x6.5x150, 1.2x8.0x175, 1.6x10x200

Stubby 2x25, 5.5x25

160PH PH 1x80, PH2x100, PH 3x150

170ELS 0.5x3.50x100, 0.8x4.0x125, 1.2x6.5x200

› 9x Drawers with customised high-density foam inserts. › Extra space provided for storing additional tools in 3 empty drawers.

SORTIMO

232

SORTIMO

GENERAL TOOL ASSORTMENT

236

I-BOXX® RACK AKTIV

237

L-BOXX®

236

I-BOXX® 72

237

L-BOXX® ROLLER

237

UNIVERSAL PULLER KIT

237

234

SORTIMOSORTIMO

THE CHALLENGE

› Tools, machines and materials must be easily, safely, quickly and conveniently transported to the place of use i.e. in a preferably, resources saving manner. › Lengthy loading times must be avoided at all cost – guaranteed load securing a pre-condition here! › GEDORE’s Sortimo® transport box system relies on a tried-and-tested mobility standard. › The perfect alliance for intelligent, e�cient process and project design planning.

THE SOLUTION

› Well structured and logical tool assortments and tool modules in the Sortimo® transport box system. › GEDORE L-BOXX® 136 with front grip and GEDORE i-BOXX® 72 powered by Sortimo® form the tried-and-tested basis for

GEDORE ‘MIXX AND CLICK’. › Every GEDORE L-BOXX® is supplied with a diagram in the lid to maintain order and optimise storage space. › The ‘To Go’ workshop is perfectly suited for mobile deployments. › Multiple compatibility and thus extremely �exible and highly individualised:

• The GEDORE ‘MIXX AND CLICK’ kit features untold combinations based on your requirements and also on the modules of other manufacturers (e.g. Bosch electrical tools). • This in combination with other Sortimo® components (transport boxes and system components) gives rise to a well organised mobile workshop. • Perfectly tailored to your personal needs.

235

THE ADVANTAGES:

› Intelligent order systems.

› Flexible, modular and individual.

› Ideal for mobile deployments.

› Diverse and highly e�cient.

› Quick accessing of tools – perfect organisation.

› Transport box standard – e.g. compatible with electrical tool manufacturers.

› Guaranteed safety.

236

SORTIMO

THE HEART OF THE KIT - GEDORE L-BOXX® 136 WITH FRONT GRIP, POWERED BY SORTIMO®.

FEATURES

› Sturdy construction. › Easy and convenient transportation of tools to the place of use. › Impact-resistant ABS plastic. › Standard lid handle to carry the L-BOXX® horizontally. › Additional kind-to-hands front grip to carry the L-BOXX® vertically. › Spray protected. › With diagram to maintain order and optimise storage space. › Easy-click system: Practical connector for two or more L-BOXX®es, for secure grip and easy transport. › No-problem integration in vehicles with the TÜV-tested Sortimo® vehicle fttings.

T ! SORTIMO GENERAL

TOOL ASSORTMENT 1/2"39 pieces

› Dimensions: 442x357x151mm.

Code No. Screwdrivers Allen Keys Ratchet Sockets Accessories 0

677001 Sortimo Tool Assortment including box + insert

21505.5-1506.52160PH1PH2PH3

42-88M 2 2.5 3 4 5 6 8 10

$ 1993 U-10 T D19 10 11 12 13 14 15 16 17 18 19 21 22 24

1990-125 1990-250

+ 1987-375145-10C95-200Voltage Tester8601-5008250-200 JC8316-200 JC62-200

8.90

1100L GEDORE L-BOXX®

› Rugged construction. › Impact-resistant ABS plastic. › Splashproof. › Top and front handle for variable transport of the L-BOXX®. › With tool board for order and more storage space. › Easy-click plug system: Practical plug connection for two or more

L-BOXX®es, for secure grip and easy transport. › For integration in vehicles with Sortimo® vehicle equipment. › Dimensions: W=442 x D=357 x H=151mm.

Code No. 0

2823691 1100L 2.20

!

237

1101L GEDORE I-BOXX®

1101K GEDORE I-BOXX® RACK AKTIV

› Shelf-like holder for any i-BOXX® 72 (No. 1101 L, 1101 CT). › Easy click attaching system, thus compatible with the GEDORE L-BOXX® 136 or with any other

L-BOXX® on the market.

Code No. w d h 0

2823713 1101 K 442 357 100 1.10

1100R GEDORE L-BOXX® ROLLER

1100-1.04 UNIVERSAL PULLER ASSORTMENT IN L-BOXX® › 2- and 3-arm cross-beam. › With rigid slim legs and extensions. › Extra-slim pulling legs for cramped spaces are attached for self-mounting. › 12 di�erent pullers can be combined. › External Ø up to 130mm, internal Ø up to 170mm with a 200mm clamping reach.

Code No. Contents 0

2838362 1100-1.04 L-Boxx® 136 no. 1100L+ assortment no. 1100 CT2-1.04

6.30

Code No. w d h 0

2823705 1101 L 367 316 72 0.900Code No. w d h 0

2823756 1101 R 646 492 184 3.80

› Small parts case with practical transparent cover. › Ideal for keeping small parts and accessories. › Optional inset boxes i3 for an individual range. › Comfort handle.

› Practical, mobile platform for all L-BOXX®. › Simply �t and click into place. › Four swivel castors for self-assembly of which two have brakes. › Load capacity up to 100kg.

MERCHANDISERS

238

MERCHANDISERS

CONCEPTS

240

SOCKET DISPLAY BOX

243

DISPLAY UNITS

243

SCREWDRIVER DISPLAY UNIT

243

240

MERCHANDISERS

No. Code Opening Order 1B-6mm 600040C 11B-7mm 600059C 11B-8mm 600067C 11B-9mm 600075C 11B-10mm 600083C 11B-11mm 600091C 11B-12mm 600105C 11B-13mm 600113C 11B-14mm 600121C 11B-15mm 600148C 11B-16mm 600156C 11B-17mm 600164C 11B-18mm 600172C 11B-19mm 600180C 11B-20mm 600199C 11B-21mm 600202C 11B-22mm 600210C 1D19 8mm 613304C 1D19 9mm 613312C 1D19 10mm 613320C 1

No. Code Opening Order

D19 11mm 613339C 1D19 12mm 613347C 1D19 13mm 613355C 1D19 14mm 613363C 1D19 15mm 613371C 1D19 16mm 613398C 1D19 17mm 613401C 1D19 18mm 613428C 1D19 19mm 613436C 1D19 20mm 613444C 1D19 21mm 613452C 1D19 22mm 613460C 142-88M 012104 11985 614335C 11987 614343C 11990/75mm 614378C 11990/125mm 614386C 11990/250mm 614394C 11993 Z/94 614459C 11995 614475C 1

No. Code Opening Order

1997/375 614491C 1D19 HMZ 614610 136/1 6327320 162 / 200mm 636819 162 / 250mm 636827 1137/250mm 640670 1145 / 250mm 641200 1225 / 250mm 645036 1534 10mm 651206C 1534 11mm 651214C 1534 12mm 651222C 1534 13mm 651230C 1534 14mm 651249C 1534 15mm 651257C 1534 16mm 651265C 1534 17mm 651273C 1534 18mm 651516C 1534 19mm 651281C 1

1282-C19-1BMZ-PL-6SD 679232 1

CONCEPT OPTION 1 1 STAND MERCHANDISER

THE PICTURES SHOWN ON THIS PAGE IS FOR ILLUSTRATION PURPOSES ONLY. ACTUAL PRODUCTS MAY VARY DEPENDING ON CUSTOMERS REQUIREMENTS.THE PICTURES SHOWN ON THIS PAGE IS FOR ILLUSTRATION PURPOSES ONLY. ACTUAL PRODUCTS MAY VARY DEPENDING ON CUSTOMERS REQUIREMENTS.

Code No. Opening order Code No. Opening order Code No. Opening order

241

1B-6mm 600040C 11B-7mm 600059C 11B-8mm 600067C 11B-9mm 600075C 11B-10mm 600083C 11B-11mm 600091C 11B-12mm 600105C 11B-13mm 600113C 11B-14mm 600121C 11B-15mm 600148C 11B-16mm 600156C 11B-17mm 600164C 11B-18mm 600172C 11B-19mm 600180C 11B-20mm 600199C 11B-21mm 600202C 11B-22mm 600210C 11B-23mm 600229C 11B-24mm 600237C 11B/04M 601152 11B/17M 601268 11B/26M 601276 1D19 8mm 613304C 1D19 9mm 613312C 1D19 10mm 613320C 1D19 11mm 613339C 1D19 12mm 613347C 1D19 13mm 613355C 1D19 14mm 613363C 1D19 15mm 613371C 1D19 16mm 613398C 1D19 17mm 613401C 1D19 18mm 613428C 1D19 19mm 613436C 1D19 20mm 613444C 1D19 21mm 613452C 1D19 22mm 613460C 1D19 23mm 613479C 1D19 24mm 613487C 1

IN19 5mm 615315C 1IN19 6mm 615323C 1IN19 7mm 615331C 1IN19 8mm 615358C 1IN19 9mm 615366C 1IN19 10mm 615374C 1IN19 12mm 615382C 1IN19 14mm 615390C 1IN19 17mm 615404C 1IN19 19mm 615412C 142-88M 6349051 142KL-9M 6351978 143TX-09 6360959 11985 614335C 11987 614343C 11990/75mm 614378C 11990/125mm 614386C 11990/250mm 614394C 11993 U-10T 614262C 11993 Z/94 614459C 11995 614475C 11997/375 614491C 11997/450 614556C 1D19 HMZ 614610 1D19 TMZ 614831 128 PU 622761 136/1 6327320 138/400mm 633267C 162 / 150mm 636800 162 / 200mm 636819 162 / 250mm 636827 162 / 300mm 636835 162 / 375mm 636843 162 / 450mm 636851C 1137/250mm 640670 1145 / 250mm 641200 12150-2160 PH-06 ELS 1482320 1VDE 2160-2170 PH-06 1616048 1

2150-6.5 6679510C 1 2150-8.0 6679780C 1 2160 PH1 6683380C 1 2160 PH2 6683460C 1 2160 PH3 6683540C 12150 3-150 6680280C 1 2150 4-150 6680360C 1 2150 6.5-200 6680870C 1 2153 5.5 1482432C 1 2161 PH2 1531204C 1225 / 250mm 645036 1225 / 300mm 645044 1534 10mm 651206C 1534 11mm 651214C 1534 12mm 651222C 1534 13mm 651230C 1534 14mm 651249C 1534 15mm 651257C 1534 16mm 651265C 1534 17mm 651273C 1534 18mm 651516C 1534 19mm 651281C 11261 660876 1MV-150mm 6500720 1106 8725200 1113 8753680 1116A 8757670 14550 / 20 7601610 1S8000 6701030 18132-200JC 6719670 18250-200JC 6707310 18316-200JC 6745080 1S8003JC 6701110 18380-250TL 6752100 18531/250mm 675792 18531/300mm 675806 1

1282-C19-1BMZ-PL-6SD 679232 1

CONCEPT OPTION 2 2 STAND MERCHANDISERS

THE PICTURES SHOWN ON THIS PAGE IS FOR ILLUSTRATION PURPOSES ONLY. ACTUAL PRODUCTS MAY VARY DEPENDING ON CUSTOMERS REQUIREMENTS.

Code No. Opening order Code No. Opening order Code No. Opening order

242

MERCHANDISERS

1B 6mm 600040C 1 1B 7mm 600059C 1 1B 8mm 600067C 1 1B 9mm 600075C 1 1B 10mm 600083C 1 1B 11mm 600091C 1 1B 12mm 600105C 1 1B 13mm 600113C 1 1B 14mm 600121C 1 1B 15mm 600148C 1 1B 16mm 600156C 1 1B 17mm 600164C 1 1B 18mm 600172C 1 1B 19mm 600180C 1 1B 20mm 600199C 1 1B 21mm 600202C 1 1B 22mm 600210C 1 1B 23mm 600229C 1 1B 24mm 600237C 1 1B 25mm 600245C 1 1B 26mm 600253C 1 1B 27mm 600261C 1 1B 28mm 600288C 1 1B 29mm 600296C 1 1B 30mm 600318C 1 1B 32mm 600326C 1 1B / 04M 601152 1 1B / 17M 601268 1 1B / 26M 601276 1 D30 FMZ 623202 1 D19 8mm 613304C 1 D19 9mm 613312C 1 D19 10mm 613320C 1 D19 11mm 613339C 1 D19 12mm 613347C 1 D19 13mm 613355C 1

D19 14mm 613363C 1 D19 15mm 613371C 1 D19 16mm 613398C 1 D19 17mm 613401C 1 D19 18mm 613428C 1 D19 19mm 613436C 1 D19 20mm 613444C 1 D19 21mm 613452C 1 D19 22mm 613460C 1 D19 23mm 613479C 1 D19 24mm 613487C 1 D19 25mm 613495C 1 D19 26mm 613509C 1 D19 27mm 613517C 1 D19 28mm 613525C 1 D19 29mm 613533C 1 D19 30mm 613541C 1 D19 32mm 613576C 1 IN19 5mm 615315C 1 IN19 6mm 615323C 1 IN19 7mm 615331C 1 IN19 8mm 615358C 1 IN19 9mm 615366C 1 IN19 10mm 615374C 1 IN19 12mm 615382C 1 IN19 14mm 615390C 1 IN19 17mm 615404C 1 IN19 19mm 615412C 1 D19L 10mm 015705C 1 D19L 12mm 015706C 1 D19L 13mm 015701C 1 D19L 17mm 015703C 1 D19L 19mm 015704C 1 42 88M 6349051 1 42KL-9M 6351978 1 43TX-09 6360959 1

1985 614335C 1 1987 614343C 1 1990 / 75 614378C 1 1990 / 125 614386C 1 1990 / 250 614394C 1 1993U-10T 614262C 1 1993 Z/94 614459C 1 1995 614475C 1 1997 / 375 614491C 1 1997 / 450 614556C 1 D19 HMZ 614610 1 D19 TMZ 614831 1 SR-D19Z-10 616834 1 D32 EMZ 628026 1 KD 26R-6 621846 1 28 PU 622761 1 33 / 6S 96660 1 36 / 1 6327320 1 38 / 400 633267C 1 38 / 500 633283C 1 62 / 150mm 636800 1 62 / 200mm 636819 1 62 / 250mm 636827 1 62 / 300mm 636835 1 62 / 375mm 636843C 1 62 / 450mm 636851C 1137 / 175 6406620 1 137 / 250 640670 1 145 / 250 6412000 1 2150-2160 PH-06 ELS 1482320 1 VDE 2160-2170 PH-06 1616048 1 2150-6.5 6679510C 1 2150-8.0 6679780C 1 2160 PH1 6683380C 1 2160 PH2 6683460C 1 2160 PH3 6683540C 1

2150 3-150 6680280C 1 2150 4-150 6680360C 1 2150 6.5-200 6680870C 1 2153 5.5 1482432C 1 2161 PH2 1531204C 1 225/250 645036 1 225/300 645044 1 225/350 645052 1 225/450 645060 1 225/600 645079 1 534 10mm 651206C 1 534 11mm 651214C 1 534 12mm 651222C 1 534 13mm 651230C 1 534 14mm 651249C 1 534 15mm 651257C 1 534 16mm 651265C 1 534 17mm 651273C 1 534 18mm 651516C 1 534 19mm 651281C 1 1261 660876 1 MV 150mm 6500720 1 106 8725200 1 113 8753680 1 116A 8757670 1 4550-20 760161 1 S 8000 6701030 1 8132 - 200 JC 6719670 1 8250 - 200 JC 6707310 1 8316 - 200 JC 6745080 1 S 8003 JC 6701110 18380 - 250 TL 6752100 1 8531 / 250 675792 1 8531 / 300 675806 1 1282-C19-1BMZ-PL6SD T/ASS 679232 1 1282-C19-1BMZ-10SD T/ASS 679135 11282-FM-C19-1BMZ-2PL T/ASS 679415 1

CONCEPT OPTION 3 3 STAND MERCHANDISERS

Code No. Opening orderCode No. Opening order Code No. Opening order Code No. Opening order


243

2150 3-150 6680280C 1 2150 4-150 6680360C 1 2150 6.5-200 6680870C 1 2153 5.5 1482432C 1 2161 PH2 1531204C 1 225/250 645036 1 225/300 645044 1 225/350 645052 1 225/450 645060 1 225/600 645079 1 534 10mm 651206C 1 534 11mm 651214C 1 534 12mm 651222C 1 534 13mm 651230C 1 534 14mm 651249C 1 534 15mm 651257C 1 534 16mm 651265C 1 534 17mm 651273C 1 534 18mm 651516C 1 534 19mm 651281C 1 1261 660876 1 MV 150mm 6500720 1 106 8725200 1 113 8753680 1 116A 8757670 1 4550-20 760161 1 S 8000 6701030 1 8132 - 200 JC 6719670 1 8250 - 200 JC 6707310 1 8316 - 200 JC 6745080 1 S 8003 JC 6701110 18380 - 250 TL 6752100 1 8531 / 250 675792 1 8531 / 300 675806 1 1282-C19-1BMZ-PL6SD T/ASS 679232 1 1282-C19-1BMZ-10SD T/ASS 679135 11282-FM-C19-1BMZ-2PL T/ASS 679415 1

10002 MERCHANDISER DISPLAY UNIT

› Ideal for displaying GEDORE tools.

VB 19E SOCKET DISPLAY BOX

› Sturdy structure. › Ideal for displaying GEDORE sockets. › L=530 x W=320 x H=260mm.

SCREWDRIVER DISPLAY UNIT

› Clear perspex, embossed with GEDORE logo. Metal legs. › Ideal for displaying GEDORE screwdrivers. › L=500 x W=255 x H=420mm.

Code No. / Sizes 0

662844 MDS 50S Merchandiser & Screwdrivers 6.0

2150 4 2150 4-1502150 5.5 2160 PH12150 6.5 2160 PH22150 8 2161 PH22150 3-150 2153 5.5

Code No. / Sizes 0

515248 VB 19 E Display Box - Empty 3.8662845 VB 19 E Display Box with C19 Sockets 20.56662846 VB 19 E Display Box with D19 Sockets 21.02

Code No. / Sizes 0

580940 Gedore Merchandiser 52.0

1282-C19-1BMZ-PL-6SD TOOL ASSORTMENT 120


244

TECHNOLOGY AND SAFETY

Warranty

In terms of GEDORE’S warranty policy, all torque wrenches are covered by a lifetime guarantee against defective materials and workmanship. Provided that the tool has been correctly used for its intended purpose and allowances have been made for the wear and tear of moving parts, the torque wrench will be repaired free of charge.



Calibration

All new GEDORE torque wrenches are supplied with a SANAS certi�cate. A standard calibration and the issue of a test certi�cate will be provided as standard practice on any repair conducted.

A SANAS calibration and the issue of a SANAS calibration certi�cate will be done on request at an additional nominal charge.

OUR TORQUE WRENCH SERVICE - QUALIFIED AND CUSTOMISED

Please note that the torque wrench is an item of measuring equipment.

We recommend › Calibration once a year (DIN EN ISO 6789:2003)

or after 5000 load cycles (DIN EN ISO 6789:2003)

Your advantage › Torque wrench o�ering measurement accuracy. › Free* calibration service at Torque Tech GmbH & Co. KG.

Regular calibration, adjustment and certification. Why is this so important?

› Only then can we guarantee the precision and reliability of our torque tools over the long term. We attach a great deal of importance to this as your safety is of the utmost importance. › Because we o�er you the safety you require for everyday controlled tightening.

GEDORE - competent control at the highest level

245

S1 S2

S1 S2

WE TAKE YOUR HEALTH SERIOUSLY.

Spanners

Tool trolley

To ensure that you use our tools safely, please make youself familiar with the following information.*

Tool chests

› Do not climb or step onto the tool chest. › Never store pointed or sharp items loosely in the tool chest. Scribers can be made safe by sticking them in a cork. › To avoid injury keep your back straight when attempting to lift the tool chest.

› Only use spanner sizes and pro�les which �t the bolt or nut head. › Do not use spanners as levers or as striking tools. › Select the spanner in accordance with the screwed connection. This particularly applies to screwed connections

with high torques. › Never extend the tool lever arm except when the tools are designed especially for this purpose, e.g. single ended

ring spanners. › Never hit a spanner with a hammer except when the tools have an area designed especially for this purpose, e.g.

slogging spanners. › Always apply the spanner at a right angle to the bolt axis. › Always pull the spanner towards you. Never push the spanner away from you. If for any reason you can only press

the spanner away from you, use your open hand to prevent injuring your knuckles. › Ring spanners transmit the forces more consistently. Ring spanners are therefore more suitable for large torques. › Apply open ended spanners in such a way that the angle of the jaw is facing in the direction

of rotation. › If a torque is required for the screwed connection, use a torque wrench. › Never work with damaged spanners or attempt to repair them, rather replace them.

› Read the operating instructions. › Open only one drawer at a time, when more than one drawer is open it increases the chance of the trolley

tipping over. › Always keep the heaviest tools in the lower (heavy) drawer. Storage in the top drawers increases the chance of

the trolley tipping over. › Take note of the permissible load capacity of each drawer and the total carrying capacity of the trolley. › Never store pointed or sharp items loosely in the tool chest. Scribers can be made safe by sticking them in a

cork. › Only move the trolley when all the drawers are closed and locked. › When the trolley is staionary always set the safety brake on the swivel castors to avoid movement.

* Furthermore, the relevant safety guidelines of various institutions apply, e.g. the guidelines of the trade associations, employers' instructions and the statutory speci�cations of the respective country.

› Always wear safety goggles for tasks involving chips or the possibility of parts splintering.

› Only use the hand tools for their intended purpose. › Never modify or tamper with tools. Exceptions: Professional regrinding of

chisels, scrapers, cutting tools as well as hammer edges. › Never work with damaged tools. Damaged tools must be replaced

immediately. › Handles must be free of oil and grease. › Depending on the task, protect your hands by wearing work gloves. › Work on live circuits may only be performed by quali�ed personnel using

suitable VDE tools. › Choose a safe surface to ensure stability. Wear safety shoes. › Wear the speci�ed ear protection when working in noisy environments.

General

› Always store the heaviest tools in the bottom (heavy duty) drawer. › When the bottom drawer is opened, the centre of gravity is relocated to a

safe range. › Storing heavy tools in the upper drawers relocates the centre of gravity

upwards. › When the drawer is opened, the centre of gravity is relocated to a critical

range. › This makes the tool trolley very susceptible to lateral forces. If the trolley is

exposed to lateral forces such as impact, it can overturn. › Always observe the load capacity for each drawer to ensure that

you always stay in the safe range.

› S 1 = tool trolley centre of gravity when the drawer is closed › S 2 = tool trolley centre of gravity when the drawer is opened › Red = critical range-danger of overturning

Why should heavy tools be stored in the bottom drawer?

Screwdrivers

› Choose the screwdriver which is suitable for the respective bolt head pro�le. › Place the workpiece on a ledge or clamp it. This helps to avoid injuries incurred by sliding blades. › Avoid cuts by directing the requisite pressure for releasing or tightening

the bolt head away from your body. › Wear protective gloves when working with screwdrivers. › If the screwdriver is too long, do not under any circumstances shorten

the blade or handle. Choose a shorter screwdriver. › Do not use the screwdriver as a caulking or crushing tool. › Light hammer impact may only be applied for loosening screws using suitable screwdrivers with striking cap

or continuous blade. › If the bolt fails to loosen, use the GEDORE impact driver set

No. K 1900-013 to release the bolt without destroying it. › Insulated and tested screwdrivers must be used when working on electrical systems.

246


> >

= >

VDE tools

› Work on electrically live equipment may only be carried out by trained electricians. › Only tools and safety equipment marked with the double triangle or bell 1000V symbol

may be used. › Before commencing any work, check the insulation for damage. › Damaged tools must not be used. › The regulations of the employers’ liability insurance associations and power supply companies must

be complied with. › GEDORE VDE tools are approved for work on live circuits at voltages up to 1000V AC and 1500V DC. › Tools must not be combined unless they are designed to be securely joined together.

Pullers

› Read the operating instructions. › Use only original spare parts and accessories for your GEDORE puller. Never use worn, modi�ed

or defective spare parts or accessories. › Wear goggles and protective clothing when working. For added safety, use the GEDORE safety

cover 5.10. › Before pulling, ensure that the legs are in contact with the part to be pulled and are �rmly

tightened so that the spindle operates centrally along the axis of the puller. › Attention! When using a puller, forces of up to several tons are generated. Take care to ensure

that the puller is correctly positioned and is vertical to the component being pulled. › Do not use electric or pneumatic power or percussion drivers.

Ratchets, tools and sockets

› Ratchets are suitable for quick loosening and tightening. › Avoid jerky movements with the ratchet, e.g. caused by hammer impact. › The square drive and the tool and socket square drive must be of the same size. › Select the drive size in accordance with the screwed connection. This particularly applies to screwed

connections with high torques. › Ensure that the ball engages properly in the ball catch. › Always pull the spanner towards you. Never push the spanner away from you. If for any reason you

can only press the spanner away from you, use your open hand to prevent injuring your knuckles. › Only use suitable sockets and connections for the impact driver. Use a safety pin and ring to secure

the connection between the socket, extension and machine. › When using reducers, the smaller drive's torque always applies. › Do not use ratchets as levers or as striking tools.

Torque tools

Pipe bending systemsCutting tools

Safety notes for striking tools

› Read the operating instructions. › Never use defective or worn pipe bending systems. › Replace defective or worn parts with original parts. › Use suitable systems and tools for bending. › Wear safety goggles, safety shoes and protective clothing. › Ensure stability of the pipe bending system during the bending process.

› Always set cutting tools down on a clearly visible place. Handles should always point towards you.

› Sharpen your cutting tools regularly. Blunt cutting tools represent a greater risk of injury than sharp ones. Blunt cutting tools require more force to be applied.

› Store cutting tools separately. This protects the blades and your �ngers. › Set shears down with their tips closed. This protects the blades and your �ngers.

Chisels › Wear safety glasses and safety gloves. › Before starting work, check that the chisel blade is sharp and the striking end is burr-free. The blades

must be properly wet-sharpened. › Select the appropriate type and size of chisel for the work to be carried out. › Hold the chisel with a �rm grip. › When working, keep your eyes on the chisel tip. › Wherever possible, use a chisel with hand guard. › Never use chisels on workpieces harder than 40 HRC. › Set safety guards in place to prevent splinters and chips posing a hazard for other people.

Centre punches, drifts and mortise chisels › These tools are subject to the same safety rules as chisels.

› Read the operating instructions. › Only use correctly calibrated torque wrenches. › Treat torque wrenches as measuring equipment. Store torque wrenches carefully. › Only use torque wrenches within the permissible torque range. › Stop tightening the bolt immediately once you feel and hear the click signal. › Apply the torque wrench at a right angle to the screwed connection. › Only use original end �ttings or accessories which �t the respective torque wrench. › Where possible, do not use any reducers. › Never loosen bolts using a torque wrench. › Never use the torque wrench as a hammer. › Slacken the torque wrench after completing work. › Never use defective or worn accessory parts. Replace defective or worn parts

with original parts. › Only use one hand on the handle of the torque wrench;

two-handed operation is only possible using DREMOMETER A - F.

247

Torque multipliers

› Read the operating instructions. › Wear safety goggles, safety shoes and protective clothing. › Always inspect the torque multiplier for damage before use. › Never use electric, pneumatic or battery operated torque multipliers or impact wrenches. › Never exceed the speci�ed maximum input torque. › Always use impact sockets in accordance with DIN 3129 or ISO 2725-2 and ISO 1174. › Always securely connect the reaction arm to the support bolt. › Never extend the impact socket or connector between bolt and torque multiplier. › Never use a universal or cardan joint. › Never hit the torque multiplier with a hammer. › Do not drop the torque multiplier. › Never use the torque multiplier if it has been dropped, used to strike other objects,

or if anything has fallen on it. › Always keep hands and �ngers away from the reaction arm. › Always select an anchor point (wall, another bolt) su�cient to withstand torque

reaction forces. Reaction torque equals output torque. › Never allow the gearbox to touch a wall or other object. › Never modify the reaction arm without consulting with the manufacturer.

Hammers

Safety notes

Work gloves

Safety goggles

Ear protection

Pliers

› Always wear safety glasses and safety gloves. › Use the hammer only for its intended purpose. › Never misuse the hammer as a lever. › Before starting work, check that the hammer head is securely attached to the shaft. › Select the appropriate size hammer for the work to be carried out. › Never hit two hammers together. › Never use steel hammers on workpieces harder than 46HRC. Use suitable plastic-faced

hammers for this. If in doubt, rather use a suitable plastic-faced hammer. › Avoid bouncing blows. › Use only the work faces of the hammer. Blows with the side face damage the non-hardened

hammer eye. This can loosen the grip of the shaft in the hammer head. › If a burr forms on the pein or face of the hammer head, this must be immediately removed.

Failure to do this can pose the risk of splintering when the hammer is in use. › Grip the hammer shaft as far away from the hammer head as possible. This improves the

impact e�ect and avoids vibrations. › Do not store hammers with wooden shafts in warm, dry environments. Wood is a natural

product. Dry, warm storage conditions can cause the shaft to lose moisture and shrink, so that the hammer shaft is no longer a tight �t in the hammer head.

› Do not store the wooden shaft in too damp conditions! Too much moisture causes the wooden shaft to swell up and damages the wooden �bres. This can result in the wooden shaft snapping behind the eye area.

› For engines with ignition coils integrated in the spark plug connector (coil-on-plug), use only spark plug sockets with retainer springs. (No. 50 - 59).

› Do not use magnetic spark plug spanners on coil-on-plug spark plugs. › This can result in control unit faults.

› Read the operating instructions. › Ensure that your work gloves are suitable for the respective task to be performed. › Examine your work gloves for damage before use. Damaged work gloves must be

replaced. › Only work using work gloves which �t your hands perfectly. › Store your work gloves in a clean and dry place.

› Read the operating instructions. › Ensure that your safety goggles are suitable for the respective task to be performed. › Examine your safety goggles for damage before use. Damaged safety goggles must

be replaced. › Store safety goggles in dry areas. Use the black plastic bag provided for this purpose.

This will help you to avoid scratches on the lenses. › Clean the lenses regularly under running water, not when dry. › Do not wear safety goggles on top of standard spectacles. Mechanical e�ects can be

transferred which may be dangerous.

› Read the operating instructions. › Ensure that your ear protection is suitable for the respective task to be performed. › Examine your ear protection for damage before use. Ear protection displaying damage

must be replaced. › Wear ear protection for the entire duration of your stay in noisy areas. › Store your ear protection in a clean and dry place. › Avoid impact against the earpieces. Otherwise, this can lead to a noise level which is

harmful for your ears.

› Wear protective goggles when working with pliers. Ejected bits of wire and circlips not positioned correctly in the tip of the pliers pose a risk to your eyes.

› Check on the jaws for wear and tear. Worn jaws result in slipping and thus in accidents.

› The joint of the pliers is not to have any noticeable play. Exceptions are the sliding joints.

› When cutting wire, choose pliers that match the wire diameter and wire hardness. › Never use pliers as hammers. › Only insulated and tested pliers are to be used when working on electrical equipment. › Grip wrenches are only for brie�y �xing workpieces.

248


b1

a1a2

b2

h

L

10°

15°

a

b2b1

L

15°

a

lwc

b

70

lw

c

b

a

W3

L3

W4

T1

T2

b d

c

e

a2a1

b d

c

e

a2a1

985

775 475 400

480 x 67

480 x 137

480 x 207

480 x 67

480 x 137

480 x 207

480 x 67

480 x 137

480 x 207

985

775 475 400

480 x 67

480 x 137

480 x 207

1100

985

1100

985

640585Hub

1625

1000

985

640

550400

<

c1

bc2b

e

d

cc cc

c

dd

d

d d

e e ee

ef

b b b b

130

100200

250

TIGHTENING / TEST TORQUE

Suggested bolt tightening torque in Nm (Newton metres) Wrench/spanner test torques in accordance with DIN ISO 1711-1 (minimum guaranteed values) Nm

These torque levels are guideline values for metric standard threads in accordance with DIN ISO 261 and head sizes in accordance with DIN EN ISO 4762, DIN EN ISO 4032, DIN EN ISO 4014, and DIN 931-2, 6912, 7984 und 7990. These produce a 90% utilisation of the bolt yield strength. The calculations are based on a friction coe�cient of 0.14 (new bolt) without any after treatment, (non-lubricated). Please note: in extreme cases, e.g. for bolts lubricated with MOS2 compound and with cadmium plated connecting elements on both sides, the tightening torque should be reduced by around 20 %.

No. 2, 2A, 2B

No. 1B, 308, 7

No. 4No. 6,

No. 1B, 7, 400

No. 25 No. 26 R No. 626

No. 35 A No. 35 B No. 3112

No. 894 No. 895

Tightening values for quality grade as per DIN 267

4.6 5.6 6.9 8.8 10.9 12.9

M 2 0,123 0,162 0,314 0,373 0,520 0,628 4 1,90

M 2,2 0,196 0,265 0,510 0,598 0,843 1,010 4,5* 2,64

M 2,5 0,284 0,373 0,726 0,863 1,206 1,451 5 11,5 3,55

M 3 0,441 0,588 1,128 1,344 1,883 2,256 5,5 14,4 4,64 14,4 2,32

M 3,5 0,677 0,902 1,736 2,060 2,893 3,481 6* 17,6 7,4 5,92 17,6 2,96

M 4 1,000 1,344 2,599 3,040 4,315 5,148 7 25,2 11,4 9,12 25,2 4,56

M 5 1,916 2,648 5,099 6,031 8,483 10,2008

9*34,5 45,4

16,6 23

13,3 18,4

34,5 45,4

34,5 45,4

6,65 9,20

M 6 3,432 4,511 8,728 10,300 14,710 17,652 10 58,1 31 24,8 58,1 58,1 58,1 12,4

M 7 5,590 7,453 14,220 17,162 24,517 28,43911

12*72,7 89,1

40,4 51,5

32,3 41,2

72,7 89,1

72,7 89,1

72,7 89,1

16,1 20,6

M 8 8,238 10,787 21,575 25,497 35,304 42,16813

14*107 128

64,5 79,4

51,6 63,5

107 128

107 128

107 128

25,8 31,7

M 10 16,67 21,575 42,168 50,014 70,608 85,31715 16

17*

150 175 201

96,2 115 134

77,0 92,3 107

150 175 201

150 175 201

150 175 201

38,5 46,1 53,5

M 12 28,44 38,246 73,550 87,279 122,60 147,1018

19* 20*

230 261 294

160 186 215

128 149 172

230 261 294

230 261 294

230 261 294

64,0 74,5 86,0

M 14 45,11 60,801 116,70 138,30 194,20 235,4021

22* 23*

330 368 408

247 281 319

198 225 255

330 368 408

330 368 408

330 368 408

99,0 112 127

M 16 69,63 93,163 178,5 210,80 299,10 357,9024

25* 26*

451 496 544

359 402 449

287 322 359

451 496 544

451 496 544

451 496 544

143 161 179

M 18 95,12 127,50 245,20 289,3 411,90 490,3027

28*594 647

499 552

399 442

594 647

594 647

594 647

199 221

M 20 135,3 180,45 384,10 411,90 578,60 696,30 30 760 670 536 760 760 760 268

M 22 182,4 245,16 470,70 559,00 784,50 941,4032* 34

884 1019

804 951

643 761

884 1019

884 1019

884 1019

321 381

M 24 230,5 308,91 598,20 711,00 1000 1196 36 1165 1117 894 1165 1165 1165 447

M 27 343,2 460,90 887,50 1049 1481 1775 41 1579 1442 1154 1579 1579 1579 577

M 30 465,8 622,72 1206 1422 2010 2403 46 2067 1816 1453 2067 2067 2067 726

M 33 632,5 848,30 1628 1932 2716 3266 50 2512 2145 1716 2512 2512 2512 858

M 36 814,0 1089 2099 2481 3491 4197 55 3140 2077 3140 3140 3140 1038

M 39 1059 1412 2716 3226 4531 5443 60 3849 2471 3849 3849 1235

M 42 1304 1746 3364 3991 5609 6727 65 4021 2900 4021 4021 1422

M 45 1638 2177 4207 4992 7012 8414 70 4658 3364 4658 4658 1618

M 48 1981 2638 5080 6021 8473 10150 75 5394 3862 5394 1765

M 52 2540 3393 6541 7747 10885 13092 80 6178 4394 6178 1912

M 56 3168 4227 8149 9650 13582 16279 85 6963 6963 2059

M 60 3932 5247 10101 11964 16867 20202 90 7845 7845 -

M 64 4737 6306 12160 14416 20300 24320 95 8336 8336 -

Note: In reference to the spanner test torque as per DIN ISO 1711-1 column, we explicitly point out that these are minimum guarantee values.

Bolts from M39 in quality grades 4.6, 5.6, 6.9, 8.8, 10.9 and 12.9 are not standardised.

* These sizes are not included in DIN ISO 272

249

b1

a1a2

b2

h

L

10°

15°

a

b2b1

L

15°

a

lwc

b

70

lw

c

b

a

W3

L3

W4

T1

T2

b d

c

e

a2a1

b d

c

e

a2a1

985

775 475 400

480 x 67

480 x 137

480 x 207

480 x 67

480 x 137

480 x 207

480 x 67

480 x 137

480 x 207

985

775 475 400

480 x 67

480 x 137

480 x 207

1100

985

1100

985

640585Hub

1625

1000

985

640

550400

<

c1

bc2b

e

d

cc cc

c

dd

d

d d

e e ee

ef

b b b b

130

100200

250

b1

a1a2

b2

h

L

10°

15°

a

b2b1

L

15°

a

lwc

b

70

lw

c

b

a

W3

L3

W4

T1

T2

b d

c

e

a2a1

b d

c

e

a2a1

985

775 475 400

480 x 67

480 x 137

480 x 207

480 x 67

480 x 137

480 x 207

480 x 67

480 x 137

480 x 207

985

775 475 400

480 x 67

480 x 137

480 x 207

1100

985

1100

985

640585Hub

1625

1000

985

640

550400

<

c1

bc2b

e

d

cc cc

c

dd

d

d d

e e ee

ef

b b b b

130

100200

250

b1

a1a2

b2

h

L

10°

15°

a

b2b1

L

15°

a

lwc

b

70

lw

c

b

a

W3

L3

W4

T1

T2

b d

c

e

a2a1

b d

c

e

a2a1

985

775 475 400

480 x 67

480 x 137

480 x 207

480 x 67

480 x 137

480 x 207

480 x 67

480 x 137

480 x 207

985

775 475 400

480 x 67

480 x 137

480 x 207

1100

985

1100

985

640585Hub

1625

1000

985

640

550400

<

c1

bc2b

e

d

cc cc

c

dd

d

d d

e e ee

ef

b b b b

130

100200

250

TIGHTENING / TEST TORQUE

Wrench/spanner test torques in accordance with DIN ISO 1711-1 (minimum guaranteed values) Nm

Test torques for tightening tools for hexagon socket head screws

With internal square as per DIN 3120 DIN EN ISO 4762

No. 42T, DT42

No. 42, 42EL

No. IN 34 With hexagon head as per DIN 7422

6,3 10 12,5 20 25 6,3 10 12,5 20 25

No. 20 No.

D 20

No. 30 No.

D 30

No. 19 No.

D 19

No. 32 No.

D 32

No. D 21

No. IN 20 No. IN30 No. IN 19 No. IN 32 No. IN 21

1/4“ 3/8“ 1/2“ 3/4“ 1“ 1/4“ 3/8“ 1/2“ 3/4“ 1“

M 2 4 10,4 1,5 0,82

M 2,2 4,5* 12,6 2 1,9 1,9

M 2,5 5 15,1

M 3 5,5 17,8 2,5 3,8 3,8

M 3,5 6* 20,6 23,2

M 4 7 26,8 33,2 3 6,6 6,6 6,6

M 5 8 9*

33,6 41,1

45,5 59,9

94,1 119,2

4 16 16 16 16 16

M 6 10 49,1 76,7 147 5 30 30 30 30 30

M 7 11 12*

57,8 67,0

96 118

178 212

M 8 13 14*

68,6 68,6

141 169

249 288

67

5280

52 52 5278

5278

M 1015 16

17*

198 225 225

331 377 425

8

9

120

165

120 120 120 120

165

M 1218

19* 20*

225 225 225

477 531 569

10

12

220

370

220

370

220 220

370

M 1421

22* 23*

225 225

569 569 569

569 569

M 1624

25* 26*

569 569 569

569 583 624

14 590 590 590 590

M 18 27 28*

569 569

665 707

M 20 30 569 795 17 980 980 1000 1000 1000

M 22 32* 34

569 569

888 984

M 24 36 1084 1677 19 1360 1360 1400 1400 1400

M 27 41 1353 1910

M 30 46 1569 2143 22 2110 2100 2100

M 33 50 1569 2329 24 2750 2700

M 36 55 1569 2562 27 3910

M 39 60 1569 2795 30 4000

M 42 65 2795 32 4000

M 45 70 2795

M 48 75 2795 36 4000

M 52 80 2795

M 56 85

M 60 90

M 64 95

Note: Hand tightening sockets are unsuited to use with impact drivers. Inappropriate use poses an accident risk.

The matching test torques are derived from the theoretical load capability of the connecting square drive.

250


HEAD WIDTHS AND THREAD DIAMETERS

Nominal size DIN ISO 272

normal (large)

Thread diameter Ø Nominal size Nominal size Thread diameter Ø Nominal size

Metric as per DIN ISO 272

Metric for high-tensile bolted

structural joints as per EN 14399-4

Inch mm BS 916, 1083 Inch mm

3,2 (–)4 (–)

1,62

5 (–)5,5 (–)

2,53

5/32

3/16

0,1562

0,1875

3,97

4,76

8 BA 7 BA 6 BA

0,152 0,172 0,193

3,86 4,37 4,90

7 (–)8 (–)

45

7/32 1/4

0,2187 0,2500

5,56 6,35

5 BA 4 BA

1/16 W

0,220 0,248 0,256

5,59 6,30 6,90

10 (–)11 (–)

67

9/32

5/16

0,2812

0,3125

7,14

7,94

3 BA 3/32 W

2 BA

0,282 0,297 0,324

7,16 7,54 8,23

13 (–)16 (–)

810

11/32 3/8

13/32

0,3438 0,3750 0,4062

8,73 9,52

10,32

1/8 W 1 BA 0 BA

(3/16)

(7/32)

0,340 0,365 0,413

8,64 9,27

10,49

18 (21)21 (24)

22

1214

12

7/16

1/2

0,4375

0,5000

11,11

12,70

3/16 W

1/4 W

1/4

5/16

0,445

0,525

11,30

13,34

24 (27)27 (30)

1618 16

9/16 19/32

5/8

0,5625 0,5938 0,6250

14,29 15,08 15,88

5/16 W 3/8 0,600 15,24

30 (34)32

34 (36)

20

2220

11/16

3/4

0,6875

0,7500

17,46

19,053/8 W 7/16 0,710 18,03

36 (41)41 (46)

2427

2224

25/32 13/16

7/8

0,7812 0,8125 0,8750

19,84 20,64 22,22

7/16 W 1/2 0,820 20,83

46 (50)50 (55)

3033

2730 15/16

1.0,9375 1,0000

23,81 25,40

1/2 W

9/16

0,920

23,37

55 (60)60 (65)

3639 36

1.1/16 1,0625 26,99

9/16 W

5/8 W

5/8

(11/16)

1,010

1,100

25,65

27,94

65 70

4245

1.1/8 1.3/16 1.1/4

1,1250 1,1875 1,2500

28,58 30,16 31,75

11/16 W 3/4 1,200 30,48

7580

4852

1.5/16 1.3/8

1.7/16

1,3125 1,3750 1,4375

33,34 34,92 36,51

3/4 W 13/16 W

7/8 (15/16)

1,300 1,390

33,02 35,31

8590

5660

1.1/2 1.5/8

1.11/16

1,5000 1,6250 1,6875

38,10 41,28 42,86

7/8 W

1. W

1.

1.1/8

1,480

1,670

37,59

42,42

95100

6468

1.3/4 1.13/16

1.7/8

1,7500 1,8125 1,8750

44,45 46,04 47,62

1.1/8 W 1.1/4 1,860 47,24

105110

7276

2. 2.1/16 2.3/16

2,0000 2,0625 2,1875

50,80 52,39 55,56

1.1/4 W 1.3/8 2,050 52,07

115120

8085

2.1/4 2.3/8

2.7/16

2,2500 2,3750 2,4375

57,15 60,32 61,91

1.3/8 W

1.1/2 W

1.1/2

1.5/8

2,220

2,410

56,39

61,21

130 90 2.9/16 2.5/8 2.3/4

2,5625 2,3750 2,7500

65,09 66,68 69,85

1.5/8 W

1.3/4 W

1.3/4

2.

2,580

2,760

65,53

70,10

135 95 2.13/16 2.15/16

3

2,8125 2,9375 3,0000

71,44 74,61 76,20

(1.7/8W) 76,70

145 100 3.1/8 3.3/8 3.1/2

3,1250 3,3750 3,5000

79,38 85,72 88,90

2.1/4

2.1/2

3,150

3,550

80,01

90,17

150 105 3.3/4 3.7/8

3,7500 3,8750

95,25 98,42 2.3/4 3,890 98,81

155 110 4.1/8 4.1/4 4.1/2

4,1250 4,2500 4,5000

104,78 107,95 114,30

3.

3.1/4

4,180

4,530

106,17

115,06

165 115

4.5/8 4.7/8

5.

4,6250 4,8750 5,0000

117,48 123,82 127,00

3.1/2 4,850 123,19

170 120 5.1/4 5.3/8 5.5/8

5,2500 5,3750 5,6250

133,35 136,52 142,88

3.3/4

4.

5,180

5,550

131,57

140,97

180 125 5.3/4 6.

6.1/8

5,7500 6,0000 6,1250

146,05 152,40 155,58 4.1/2 6,380 162,05

185 130

200 140210 150

251

!

SPANNER SIZES TOLERANCE FOR BOLTS AND SOCKET WRENCHES

Nominal size/s in mm

Tolerance class 1 as per ISO 691 dimensions

Tolerance class 2a as per ISO 691 dimensions

min. max. min. max.

2 ≤s < 33 ≤s < 44 ≤s < 6

+ 0,02+ 0,02+ 0,02

+ 0,08+ 0,10+ 0,12

+ 0,02+ 0,02+ 0,02

+ 0,12+ 0,14+ 0,16

3 ≤s < 1010 ≤s < 1212 ≤s < 14

+ 0,03+ 0,04+ 0,04

+ 0,15+ 0,19+ 0,24

+ 0,03+ 0,04+ 0,04

+ 0,19+ 0,24+ 0,30

14 ≤s < 1717 ≤s < 1919 ≤s < 26

+ 0,05+ 0,05+ 0,06

+ 0,27+ 0,30+ 0,36

+ 0,05+ 0,05+ 0,06

+ 0,35+ 0,40+ 0,46

26 ≤s < 3333 ≤s < 5555 ≤s < 75

+ 0,08+ 0,10+ 0,12

+ 0,48+ 0,60+ 0,72

+ 0,08+ 0,10+ 0,12

+ 0,58+ 0,70+ 0,92

75 ≤s < 105105 ≤s < 150150 ≤s < 210

+ 0,15+ 0,20+ 0,25

+ 0,85+ 1,00+ 1,22

+ 0,15+ 0,20

-

+ 1,15+ 1,40

-

This tolerance class applies only to ring spanners or socket wrenches that have not been manufactured by material removal.

Spanner sizes in accordance with this international standard must be marked with:a) Spanner head size.b) Reference to the international standard, i.e. ISO 691.c) Nominal sizes in millimetres.d) Tolerance class 1 or 2.

Conversion tables Inch to decimal-inches and mm

in. dec.in. mm.01/641/323/64

00.0156250.031250.046875

00,39690,79381,1906

1/165/643/327/64

0.06250.0781250.093750.109375

1,58751,98442,38122,7781

1/89/645/3211/64

0.1250.1406250.156250.171875

3,17503,57193,96884,3656

3/1613/647/3215/64

0.18750.2031250.218750.234375

4,76255,15945,55625,9531

1/417/649/3219/62

0.250.2656250.281250.296875

6,35006,74697,14387,5406

5/1621/6411/3223/64

0.31250.3281250.343750.359375

7,93758,33448,73129,1281

3/825/6413/3227/64

0.3750.3906250.406250.421875

9,5250 9,921910,318810,7156

7/1629/6415/3231/64

0.43750.4531250.468750.484375

11,112511,509411,906212,3031

in. dec.in. mm.1/233/6417/3235/64

0.50.5156250.531250.546875

12,700013,096913,493813,8906

9/1637/6419/3239/64

0.56250.5781250.593750.609375

14,287514,684415,081215,4781

5/841/6421/3243/64

0.6250.6406250.656250.671875

15,875016,271916,668817,0656

11/1645/6423/3247/64

0.68750.7031250.718750.734375

17,462517,859418,256218,6531

3/449/6425/3251/62

0,750,7656250,781250,796875

19,050019,446919,843820,2406

13/1653/6427/3255/64

0,81250,8281250,843750,859375

20,637521,034421,431221,8281

7/857/6429/3259/64

0,875 0,8906250,906250,921875

22,2250 22,621923,018823,4156

15/1661/6431/3263/641

0,93750,9531250,968750,9843751

23,812524,209424,606225,003125,4000

252


TORQUE CONVERSION TABLES

Conversion formula: Units to be converted x factor = corresponding unit

Example: Conversion of 5lbf·ft in cNm

Solution: 5 x 135.6 = 678cNm

ApplicationCorresponding unit

= mNm = cNm = Nm = ozf·in = lbf·in = lbf·ft = gf·cm = f·cm (kp·cm) = kgf·m (kp·m)

1 mN·m 1 0,1 0,001 0,142 0,009 0,0007 10,2 0,01 0,0001

1 cN·m 10 1 0,01 1,416 0,088 0,007 102 0,102 0,001

1 N·m 1000 100 1 141,6 8,851 0,738 10197 10,2 0,102

1 ozf·in 7,062 0,706 0,007 1 0,0625 0,005 72 0,072 0,0007

1 lbf·in 113 11,3 0,113 16 1 0,083 1152,1 1,152 0,0115

1 lbf·ft 1356 135,6 1,356 192 12 1 13826 13,83 0,138

1 gf·cm 0,098 0,01 0,0001 0,014 0,0009 0,00007 1 0,001 0,00001

1 kgf·cm (kp·cm) 98,07 9,807 0,098 13,89 0,868 0,072 1000 1 0,01

1 kgf·m (kp·m) 9807 980,7 9,807 1389 86,8 7,233 100000 100 1

Conversion from m in kgf·m (kp·m) 1N·m = 0,102 kgf·m

N·m 0 1 2 3 4 5 6 7 8 9

0 0,00 0,10 0,20 0,31 0,41 0,51 0,61 0,71 0,82 0,92

10 1,02 1,12 1,22 1,33 1,43 1,53 1,63 1,73 1,84 1,94

20 2,04 2,14 2,24 2,35 2,45 2,55 2,65 2,75 2,86 2,96

30 3,06 3,16 3,26 3,37 3,47 3,57 3,67 3,77 3,87 3,98

40 4,08 4,18 4,28 4,38 4,49 4,59 4,69 4,79 4,89 5,00

50 5,10 5,20 5,30 5,40 5,51 5,61 5,71 5,81 5,91 6,02

60 6,12 6,22 6,32 6,42 6,53 6,63 6,73 6,83 6,93 7,04

70 7,14 7,24 7,34 7,44 7,55 7,65 7,75 7,85 7,95 8,06

80 8,16 8,26 8,36 8,46 8,57 8,67 8,77 8,87 8,97 9,08

90 9,18 9,28 9,38 9,48 9,59 9,69 9,79 9,89 9,99 10,10

100 10,20 10,30 10,40 10,50 10,60 10,71 10,81 10,91 11,01 11,11

Conversion from kgf·m (kp·m) in Nm 1 kgf·m (kp·m) = 9,807 N·m

kgf·m(kp·m)0 1 2 3 4 5 6 7 8 9

0 0,00 9,81 19,61 29,42 39,23 49,03 58,84 68,65 78,45 88,26

10 98,07 107,87 117,68 127,49 137,29 147,10 156,91 166,71 176,52 186,33

20 196,13 205,94 215,75 225,55 235,36 245,17 254,97 264,78 274,59 284,39

30 294,20 304,01 313,81 323,62 333,43 343,23 w353,04 362,85 372,65 382,46

40 392,27 402,07 411,88 421,69 431,49 441,30 451,11 460,91 470,72 480,53

50 490,33 500,14 509,95 519,75 529,56 539,37 549,17 558,98 568,79 578,59

60 588,40 598,21 608,01 617,82 627,63 637,43 647,24 657,05 666,85 676,66

70 686,47 696,27 706,08 715,89 725,69 735,50 745,31 755,11 764,92 774,73

80 784,53 794,34 804,15 813,95 823,76 833,57 843,37 853,18 862,99 872,79

90 882,60 892,41 902,21 912,02 921,83 931,63 941,44 951,25 961,05 970,86

100 980,67 990,47 1000,28 1010,08 1019,89 1029,70 1039,50 1049,31 1059,12 1068,92

Conversion from N·m in Ibf·ft 1N·m=0,7376 lbf·f t

N·m 0 1 2 3 4 5 6 7 8 9

0 0,00 0,74 1,48 2,21 2,95 3,69 4,43 5,16 5,90 6,64

10 7,38 8,11 8,85 9,59 10,33 11,06 11,80 12,54 13,28 14,01

20 14,75 15,49 16,23 16,96 17,70 18,44 19,18 19,91 20,65 21,39

30 22,13 22,86 23,60 24,34 25,08 25,81 26,55 27,29 28,03 28,76

40 29,50 30,24 30,98 31,72 32,45 33,19 33,93 34,67 35,40 36,14

50 36,88 37,62 38,35 39,09 39,83 40,57 41,30 42,04 42,87 43,52

60 44,25 44,99 45,73 46,47 47,20 47,94 48,68 49,42 50,15 50,89

70 51,63 52,37 53,10 53,84 54,58 55,32 56,05 56,79 57,53 58,27

80 59,00 59,74 60,48 61,22 61,96 62,69 63,43 64,17 64,91 65,64

90 66,38 67,12 67,86 68,59 69,33 70,07 70,81 71,54 72,28 73,02

100 73,76 74,49 75,23 75,97 76,71 77,44 78,18 78,92 79,66 80,39

Conversion from Ibf·ft in N·m 1 lbf·f t = 1,356 N·m

Ibf·ft 0 1 2 3 4 5 6 7 8 9

0 0,00 1,36 2,71 4,07 5,42 6,78 8,13 9,49 10,85 12,20

10 13,56 14,91 16,27 17,63 18,98 20,34 21,69 23,05 24,40 25,76

20 27,12 28,47 29,83 31,18 32,54 33,90 35,25 36,61 37,96 39,32

30 40,67 42,03 43,39 44,74 46,10 47,45 48,81 50,16 51,52 52,88

40 54,23 55,59 56,94 58,30 59,66 61,01 62,37 63,72 65,08 66,43

50 67,79 69,15 70,50 71,86 73,21 74,57 75,93 77,28 78,64 79,99

60 81,35 82,70 84,06 85,42 86,77 88,13 89,48 90,84 92,20 93,55

70 94,91 96,26 97,62 98,97 100,33 101,69 103,04 104,40 105,75 107,11

80 108,46 109,82 111.18 112,53 113,89 115,24 116,60 117,96 119,31 120,67

90 122,02 123,38 124,73 126,09 127,45 128,80 130,16 131,51 132,87 134,23

100 135,58 136,94 138,29 139,65 141,00 142,36 143,72 145,07 146,43 147,78

Conversion from Nm in Ibf·in 1 N·m = 8,851 lbf·in

N·m 0 1 2 3 4 5 6 7 8 9

0 0,00 8,85 17,70 26,55 35,40 44,25 53,10 61,96 70,81 79,66

10 88,51 97,36 106,21 115,06 123,91 132,76 141,61 150,46 159,31 168,16

20 177,02 185,87 194,72 203,57 212,42 221,27 230,12 238,97 247,82 256,67

30 265,52 274,37 283,22 292,08 300,93 309,78 318,63 327,48 336,33 345,18

40 354,03 362,88 371,73 380,58 389,43 398,28 407,14 415,99 424,84 433,69

50 442,54 451,39 460,24 469,09 477,94 486,79 495,64 504,49 513,34 522,20

60 531,05 539,90 548,75 557,60 566.45 575,30 584,15 593,00 601,85 610,70

70 619,55 628,40 637,26 646,11 654,96 663,81 672,66 681,51 690,36 699,21

80 708,06 716,91 725,76 734,61 743,46 752,32 761,17 770,02 778,87 787,72

90 796,57 805,42 814,27 823,12 831,97 840,82 849,67 858,52 867,38 876,23

100 885,08 893,93 902,78 911,63 920,48 929,33 938,18 947,03 955,88 964,73

Conversion from Ibf·in in Nm 1 lbf·in = 0,113 N·m

Ibf·in 0 1 2 3 4 5 6 7 8 9

0 0,00 0,11 0,23 0,34 0,45 0,56 0,68 0,79 0,90 1,02

10 1,13 1,24 1,36 1,47 1,58 1,69 1,81 1,92 2,03 2,15

20 2,26 2,37 2,49 2,60 2,71 2,82 2,94 3,05 3,16 3,28

30 3,39 3,50 3,62 3,73 3,84 3,95 4,07 4,18 4,29 4,41

40 4,52 4,63 4,75 4,86 4,97 5,08 5,20 5,31 5,42 5,54

50 5,65 5,76 5,87 5,99 6,10 6,21 6,33 6,44 6,55 6,67

60 6,78 6,89 7,00 7,12 7,23 7,34 7,46 7,57 7,68 7,80

70 7,91 8,02 8,13 8,25 8,36 8,47 8,59 8,70 8,81 8,93

80 9,04 9,15 9,26 9,38 9,49 9,60 9,72 9,83 9,94 10,06

90 10,17 10,28 10,39 10,51 10,62 10,73 10,58 10,96 11,07 11,19

100 11,30 11,41 11,52 11,64 11,75 11,86 11,98 12,09 12,20 12,31

Torque conversion factorsUnits to be

253

Examples

Comparison table of Vickers-Brinell-Rockwell hardness and tensile strength

Important pre�x characters

Giga G 1.000.000.000 = 109

Mega M 1.000.000 = 106

Kilo k 1.000 = 103

Hecto H 100 = 102

Deca Da 10 = 101

Deci d 0,1 = 10-1

Centi c 0,01 = 10-2

Milli m 0,001 = 10-3

Micro µ 0,000001 = 10-6

Nano n 0,000000001 = 10-9

Conversion table, force and torque1 newton = 0,102 kp

= 9,81 N= 9,81 Nm

1 kilopond1 kilopond metre

Important SI units with conversions to old but still commonly used units

Length metre mMasa kilogramme Time second sForce newton N = m/s2 1 N = 0,102 kpTorque newton metre Nm 9,81 N·m = 1 kp·mEnergy (work) joule J = NmHeat quantity joule J 1 J = 0,239 calPower watt W = Nm/s 1 kW = 1,36 PS = 860 kcal/hPressure pascal Pa = N/m2 100 000 Pa = 1 bar = 10 mWSElectrical current ampere ATemperature kelvin K 1 K = 1 °C

Material propertiesDensity Expansion Melting point Modulus of elasticityg/cm3 1/°C °C N/mm

Aluminium 2,7 0,000024 660,1 72 000Lead 11,3 0,000029 327,3 16 000Iron (Steel) 7,86 0,000012 1540 210 000Gold 19,3 0,000014 1063 79 000Copper 8,9 0,000017 1083 126 000Zinc 7,1 0,000026 419 94 000Glass 2,2–2,9 0,000008 800–1500 68 000Air 0,0013 0,0036Wood 0,5–0,7 10 000

Plastics / synthetic materials: PS, 1,05 0,00008 3 400PP, 0,9 0,00018 1 200ABS 1,05 0,00010 2 500

Conversion table, mass and weight1 megagramme (Mg) = 1.000 kg = 10.000 hg = 100.000 dag = 1.000.000 g1 ton (to.) = 1.000 kg1 kilogramme (kg) = 10 hg = 100 dag = 1000 g1 hectogramme (hg) = 10 dag = 100 g1 decagramme (dag) = 10 g1 gramme (g) = 10 dg = 100 cg = 1000 mg1 decigramme (dg) = 10 cg = 100 mg1 centigramme (cg) = 10 mg1 miligramme (mg) = 1 mg

Example 1:Expansion of a steel body of 100mm in length at a temperature of 10°C. Lengthy expansion coe�cient x °C exp. = 100mm x 0,000012 x 10 = 0,012mm = 12µm

Example 2:Elastic expansion e = s/E. A body of 100mm in length made of ABS is stretched with s = 50N/mm2. e = 50N/mm2: 2500N/mm2 = 0.02. The expansion is: 10 mm x 0.02 = 2mm.

Example 3:Two steel plates with a total thickness of 20mm are pre-stressed by means of a screw connection of s = 50N/mm2: e = 50: 210000 = 0.00024. The compression in the surrounding area of the screw is 2 mm x 0.00024 = 0,0048mm = 5µm.

The elastic compression induces a continuous pre-tension of the screw connection. A properly tensed screw connection is sel�nhibiting.

Vickers hardness Brinell hardness Rockwell hardness Rockwell hardness Tensile strengthHV 30 HB 30 HRB HRC sB

N/mm2

80 80,7 36,4 – 270 85 85 42,4 – 290 90 90 47,4 – 310 95 95 52,0 – 320100 100 56,4 – 340105 105 60,0 – 360110 110 63,4 – 380115 115 66,4 – 390120 120 69,4 – 410125 125 72,0 – 420130 130 74,4 – 440135 135 76,4 – 460140 140 78,4 – 470145 145 80,4 – 490150 150 82,2 – 500155 155 83,8 – 520160 160 85,4 – 540165 165 86,8 – 550170 170 88,2 – 570175 175 89,6 – 590180 180 90,8 – 600185 185 91,8 – 620190 190 91,5 – 640195 195 94,0 – 660200 200 95,0 – 670205 205 95,8 – 680210 210 96,6 – 710215 215 97,4 – 720220 220 98,2 – 730225 225 99,0 – 750230 230 – 19,2 760235 235 – 20,2 780240 240 – 21,2 800245 245 – 22,1 820250 250 – 23,0 830255 255 – 23,8 850260 260 – 24,6 870265 265 – 25,4 880270 270 – 26,9 900275 275 – 27,1 920280 280 – 27,6 940285 285 – 28,3 950290 290 – 29,0 970295 295 – 29,6 990300 300 – 30,3 1010310 310 – 31,5 1040320 320 – 32,7 1080330 330 – 33,8 1110340 340 – 34,9 1140350 350 – 36,0 1170360 359 – 37,0 1200370 368 – 38,0 1230380 376 – 38,9 1260390 385 – 39,8 1290400 392 – 40,7 1320410 400 – 41,5 1350420 408 – 42,4 1380430 415 – 43,2 1410440 423 – 44,0 1430450 430 – 44,8 1460460 – – 45,6 (1490)470 – – 46,3 (1520)480 – – 47,0 (1550)490 – – 47,7 (1580)500 – – 48,3 (1600)510 – – 49,1 (1630)520 – – 49,7 (1660)530 – – 50,4 (1690)540 – – 51,0 (1710)550 – – 51,6 (1740)560 – – 52,2 (1770)570 – – 52,8 (1790)580 – – 53,3 (1820)590 – – 53,9 (1850)600 – – 54,4 (1870)610 – – 55,0 (1900)620 – – 55,5 (1930)630 – – 56,0 (1950)640 – – 56,5 (1980)650 – – 57,0 (2000)660 – – 57,5 (2030)670 – – 58,0 (2050)680 – – 58,5 (2080)690 – – 59,0 (2110)700 – – 59,5 (2130)720 – – 60,4 (2170)740 – – 61,2 (2220)760 – – 62,0 (2260)780 – – 62,8 (2300)800 – – 63,6 –820 – – 64,3 –840 – – 65,0 –860 – – 65,7 –880 – – 66,3 –900 – – 66,9 –920 – – 67,5 –940 – – 68,0 –

254

TECHNOLOGY AND SAFETYARTICLE INDEX

ARTICLE INDEXPageArticle No.


1.07/K ........................... Puller Set ....................................................................................203

1.15 ............................... Triple Grip Puller .......................................................................199

1.26 .............................. Nut Splitter - Hydraulic ..........................................................200

1.30 ............................... Internal Extractor .....................................................................200

1.31 ............................... Internal Extractor Set ..............................................................203

1.36 ............................... Support Brace ...........................................................................201

1.38 ............................... Separator Puller ........................................................................201

1.40 ............................... Bearing Separator ....................................................................201

1.67 ............................... Steering Wheel Puller .............................................................201

1.73 ............................... Ball Joint Puller .........................................................................202

1.75 ............................... Oil Filter Hook ............................................................................102

1.85 ............................... Bearing Installation Set ..........................................................202

100 ................................ Centre Punch .............................................................................142

106 ................................ Chisel & Punch Set ...................................................................143

108 ................................ UNI Hand Guard .......................................................................142

1001 .............................. Electricians VDE Toolset .........................................................153

1100-1.04 ................... Universal Puller Set ........................................................203/237

1100L ........................... Sortimo L-Boxx..........................................................................236

1100R .......................... Sortimo L-Boxx Roller .............................................................237

1101K ........................... Rack for Sortimo Box ..............................................................237

1101L ........................... Sortimo I-Boxx ..........................................................................237

1101-001 ..................... Circlip Pliers Set ..........................................................................91

1101-1.29/3K ............. Ball Bearing Extractor Set ......................................................202

1102-003 ..................... Pliers Set ........................................................................................84

113 ................................ Drift Punch Set ..........................................................................143

116 ................................ Pin Punch Set.............................................................................143

121 G ............................ Suction-Cup Lifter ..................................................................103

121 G-3 ........................ Suction-Cup Lifter ..................................................................103

125 ................................ Piston Ring Clamp Band ........................................................104

126 ................................ Piston Ring Pliers ......................................................................104

126-060 ....................... Piston Ring Pliers ......................................................................104

1260 ............................. Toolbox - 3 Compartments ..................................................116


128 ............................... Valve Spring Tensioner ...........................................................104

1280 .............................. Toolbox - 3 Compartments - Aluminium.........................117

1280/1281/1282 - Trays & Inserts ................................................................................117

1281 .............................. Toolbox - 5 Compartments - Aluminium.........................117

1281/1282 ................. Tool Assortments ............................................................119-126

1282/5.......................... Toolbox - 5 Compartments ..................................................116

132 ................................ Hose Clamp Pliers ...................................................................105

132 CLIC ...................... Hose Clamp Pliers ....................................................................105

133 ................................ Open Ended Slogging Spanner ...........................................20


134 ............................... Straight Jaw Grip Wrench .......................................................91

135 ................................ Brake Spring Pliers ...................................................................105

137 ................................ Grip Wrenches .............................................................................91

138 ................................ Welding Grip Pliers ....................................................................92

138 Y ............................. C-Grip Pliers .................................................................................92

139 ................................ Pry Bars ........................................................................................101

1401 .............................. PRO Cabinet & Tools ................................................................126

1401 .............................. Tool Cabinet ...............................................................................126

1401L ........................... Large Tool Cabinet ...................................................................127

1401L ........................... PRO Cabinet & Tools ................................................................127

1404 .............................. PRO Cabinet & Tools ................................................................128

1404 .............................. Tool Cabinet ...............................................................................128

1410 .............................. Artisan’s Tool Chest..................................................................131

142 ................................ Universal Pliers ............................................................................95

1425/3/5 ..................... Foam Inserts Spares ................................................................135

1425/27/HM .............. Modular Assortment ...............................................................135

1425/27/PL................. Modular Assortment ...............................................................135

1425/27/SD ............... Modular Assortment ...............................................................135

1425/27/SP ................ Modular Assortment ...............................................................135

1425/3.......................... Tool Chest ...................................................................................130

1425/3.......................... Workshop Tool Assortment ..................................................130

1425/41/D19 ............. Modular Tool Assortment .....................................................134

1425/41/IB ................. Modular Tool Assortment .....................................................134

1425/5.......................... Comprehensive Tool Assortment .......................................131

1425/5.......................... Tool Chest ...................................................................................131

143 ................................ Universal Pliers ............................................................................95

145 ................................ Waterpump Pliers ......................................................................95

1450S ........................... Tool Panel & Accessories .......................................................129

1460 .............................. Trays ..............................................................................................118

1460 .............................. Tool Trunk ..................................................................................118

1460L ........................... Tool Trunk 4x4 ...........................................................................118

1500 .............................. Metal Work Bench ....................................................................128

1500 .............................. Wooden Work Bench ..............................................................128

1502 ............................. Drawer Unit ................................................................................129

1510 ............................. Classic Tool Assortment .........................................................132

1510 ............................. Tool Trolley .................................................................................132

1525 ............................. Comprehensive ........................................................................133

1525 ............................. Tool Trolley .................................................................................133

1581 ............................. Tool Trolley .................................................................................134

1581 .............................. Classic Tool Assortment ........................................................134

165-171-06 ................. Electronic Screwdriver Set ......................................................70

165-TX-06 ................... Electronic Screwdriver Set ......................................................70

180 ................................ Cable Shears - Insulated ........................................................152

19 ................................... Boxes & Inserts ............................................................................52

32 ................................... Repair Kits .....................................................................................52

1930 .............................. Reducer 1/2” to 3/8” ..................................................................46

1932 .............................. Converter 1/2” to 3/4” ...............................................................46

255

ARTICLE INDEX



1985 .............................. Speed Brace Handle 1/2” .........................................................46

1987 .............................. Sliding T-Bar 1/2” ........................................................................47

1990 ............................. Extension Bar 1/2” ......................................................................47

1990M ......................... Extension with Magnet 1/2” ...................................................47

1993 U-3...................... Reversible Ratchet 1/2” ............................................................41

1993 U-10K ................ Reversible Plastic Ratchet 1/2” .............................................41

1993 U-10T ................. Reversible Ratchet 1/2” ............................................................41

1993 Z-94 ................... Reversible Ratchet & Coupler 1/2” .......................................41

1994 ............................. Square Coupler 1/2” ..................................................................47

1995 ............................. Universal Joint 1/2” ....................................................................47

1996 ............................. Power Bar 1/2” .............................................................................46

1997 .............................. Power Bar 1/2” .............................................................................46

19L ................................ Extra Deep Socket (MM) (AF) .................................................43

1B .................................. Spanner Sets ................................................................................10

1B .................................. Spanners (AF) ..............................................................................10

1B .................................. Spanners (MM) ...............................................................................9

2 ..................................... Ring Spanner Sets ......................................................................14

2 ..................................... Ring Spanners (MM) (AF)......................................................... 14

20 ................................... Socket (MM) 1/4” ........................................................................25

20L ................................ Socket Long Pattern 1/4” .........................................................26

2.10 .............................. Car Workshop Kit ......................................................................204

2.20 .............................. Truck Workshop Kit .................................................................204

2.30 .............................. Industrial Puller Kit ..................................................................204

2.40 ............................... Construction Machine Puller Kit .........................................204

20 EAU-3 ..................... Socket Set 1/4” ............................................................................24

20 EMZ ........................ Socket Set 1/4” ............................................................................24

2030 ............................. Converter 1/4” to 3/8” ...............................................................27

2087 .............................. Sliding T-Bar 1/4” ........................................................................27

2088 .............................. Flexible Extension 1/4” .............................................................27

2090 .............................. Extension 1/4” .............................................................................27

2093-U3 ...................... Reversible Ratchet 1/4” ............................................................25

2093-U10 ................... Reversible Ratchet 1/4” ............................................................25

2093-Z/94 .................. Reversible Ratchet 1/4” ............................................................25

2094 ............................. Coupler 1/4” .................................................................................27

2095 .............................. Universal Joint 1/4” ....................................................................27

2097 .............................. Swivel Handle 1/4” .....................................................................27

2098 .............................. Driving Handle 1/4” ...................................................................27

210 ................................ Chain Pipe Wrench ....................................................................94

2132 .............................. Reducer 1“ to 3/4” AF ................................................................55

2133 .............................. 3C Nut Drivers .............................................................................71

2133 .............................. 3C Nut Driver Sets ......................................................................71

2150 .............................. 3C Screwdriver ...........................................................................67

2153 .............................. 3C Stubby Screwdriver............................................................. 68

2150-2160 PH............ 3C Screwdriver Sets ...................................................................69

2160 PH ....................... 3C Screwdriver ............................................................................67

2160 PZ........................ 3C Screwdriver ............................................................................67

2161 PH ....................... 3C Stubby Screwdriver - Philip ..............................................68

2163 TX........................ 3C Torx® Screwdrivers............................................................... 68

2163 TX........................ 3C Torx® Screwdriver Set .........................................................69

2187 .............................. Sliding T-Bar 1” ............................................................................54

2190 .............................. Extension Bar 1” ..........................................................................55

2193 U-3...................... Reversible Ratchet .....................................................................53

2193-Z94..................... Reversible Ratchet .....................................................................53

2194 .............................. Square Coupler ...........................................................................55

2195 .............................. Universal Joint.............................................................................55

220 ................................ Steel Pipe Cutter .........................................................................97

2200 .............................. Number Set ................................................................................143

2201 .............................. Letter Set .....................................................................................143

225 ................................ Pipe Wrench - Stillson Type ....................................................93

227 ................................ Pipe Wrench - American Pattern .......................................... 93

227S .............................. Slogging Pipe Wrench ..............................................................94

229 ................................ Copper Pipe Cutter ....................................................................97

26 R ............................... Double Ended Box Spanners ...............................................100

26 RS ............................. Stepped Tommy Bar ................................................................100

248ST ........................... Recoil-free Hammer ................................................................142

27 ................................... Wheel Socket Wrench - Trucks ............................................101

28 PU ............................ 4-Way Wheel Wrench ..............................................................101

29 I ................................ Construction Ratchet ..............................................................13

299 ................................ Drain Plug Spanner .................................................................108

2A .................................. Heavy Duty Ring Spanner .......................................................16

2AR ............................... Extension Tube ...........................................................................16

3019 ............................. Converter 3/8” to 1/2” ...............................................................30

3020 ............................. Reducer 3/8” to 1/4” ..................................................................31

304 ................................ Half-Moon Ring Spanner Sets ...............................................15

304 ................................ Half-Moon Ring Spanners (MM) (AF) .................................. 15

306 ................................ Ring Slogging Spanners (MM) (AF) .................................... 20

3081 .............................. L-handle 3/8”................................................................................31

3087 .............................. Sliding T-bar 3/8” ........................................................................31

3090 .............................. Extension 3/8” .............................................................................31

3093-U3 ...................... Reversible Ratchet 3/8” ............................................................29

3093-Z/94 .................. Reversible Ratchet & Coupler 3/8” .......................................29

3094 ............................. Coupler 3/8” .................................................................................30

3095 ............................. Universal Joint 3/8” ....................................................................30

3096 ............................. Power Bar 3/8” .............................................................................31

3114 .............................. Crowfoot Spanner .....................................................................21

3219 .............................. Reducer 3/4” to 1/2” .................................................................52

3221 .............................. Converter 3/4” to 1” ...................................................................52

3287 .............................. Sliding T-bar 3/4” ........................................................................51

3290 .............................. Extension Bar 3/4” ......................................................................51

3293 DJ ........................ Repair Kit 3/4” ..............................................................................52

256


ARTICLE INDEX

PageArticle No.

ARTICLE INDEX

PageArticle No.


3293 U-1...................... Repair Kit 3/4” ..............................................................................52


3293 U-2...................... Repair Kit 3/4” ..............................................................................52

3293 Z .......................... Repair Ki 3/4” t .............................................................................52

3293 Z/94 .................. Reversible Ratchet 3/4” ............................................................49

3293/500 .................... Double Johnny Ratchet 3/4” ..................................................50

3293/500-24x30 ....... Double Johnny Ratchet 3/4” ..................................................50

3294 ............................. Square Coupler 3/4” ..................................................................52

3295 .............................. Universal Joint 3/4” ....................................................................52

3296 .............................. Power Bar 3/4” .............................................................................51

3296 .............................. Repair Kit 3/4” ..............................................................................52

36 ................................... Oil Filter Strap Wrench ...........................................................102

38 ................................... Tyre Lever ....................................................................................101

39 ................................... Tyre Lever ....................................................................................101

40 ................................... Hook Spanner .............................................................................21

400 ................................ Flare Nut Spanner (MM) (AF) .................................................17

4400 .............................. Flare Nut Spanner Set............................................................... 17

403 ................................ Hacksaw ......................................................................................107

40Z ................................ Pin Spanner ..................................................................................21

407 ................................ Hacksaw ......................................................................................107

4101 .............................. Torco�x SE - Torque Wrench .................................................159

4150 / 4151 ................ Torco�x FS - Torque Wrench .................................................159

42 ................................... Allen Key Sets ..............................................................................72

42 ................................... Allen Key (MM) (AF) ...................................................................72

424 ................................ Tin Snips - Ideal Pattern ...........................................................97

425 ................................ Tin Snips - Figure Pattern ........................................................97

42KL ............................. Ball Head Allen Key Set ............................................................73

42L ................................ Allen Key .......................................................................................73

42L ................................ Allen Key Sets ..............................................................................72

42SCKL......................... Ball Head Allen Key Set ............................................................74

42SCL ........................... Allen Key Set ................................................................................73

42T ................................ Allen Key (MM) (AF) ...................................................................73

43KTX ........................... Ball Head Torx Key Set ..............................................................74

43TV ............................. Torx Gauge Tester ......................................................................75

43TX ............................ Torx Allen Key ..............................................................................74

43TX ............................. Torx Allen Key Set ......................................................................74

43TXL .......................... Long Torx Allen Key ...................................................................75

43TXL ........................... Long Torx Allen Key Sets .........................................................75

44 ................................... Caliper Face Spanner ................................................................21

4530 .............................. Towrope ......................................................................................108

4549 .............................. Torco�x K - Torque Wrench ...................................................159

4550 .............................. Torco�x K - Torque Wrench ...................................................159

4611 .............................. Power Testing Screwdriver .....................................................70

5.10 ............................... Puller Safety Cover ..................................................................200

50 ................................... Spark Plug Socket ....................................................................102

5017 .............................. JAZZ Tool Assortment ............................................................112

502 ................................ Motorist Toolkit .........................................................................113

503 ................................ Handy 3-Piece Set ....................................................................109

505 ................................ Basic Home Toolset .................................................................109

507 ............................... Leisure Motorist Toolkit .........................................................113

534 ................................ Swivel Wrench .............................................................................13

534 ................................ Swivel Wrench Sets ...................................................................13

54 ................................... Spark Plug Socket ....................................................................102

55 ................................... Spark Plug Spanner .................................................................102

58 ................................... Spark Plug Spanner .................................................................102

6 .................................... Open Ended Spanners .............................................................18

62 ................................... Adjustable Wrench ....................................................................19

62H ............................... Adjustable Wrench ....................................................................19

620C ............................. Club Hammers ..........................................................................145

622C ............................. Copper Sledge Hammers ......................................................145

640S .............................. Sledge Hammers ......................................................................145

640 ................................ Magnetic Lifter ..........................................................................103

642 SP .......................... Magnetic Lifter ..........................................................................103

647 ................................ Spark Plug Brush ......................................................................103

687 ................................ Screwdriver Bits - Torx ..............................................................75

690 ................................ Screwdriver Bits - PH .................................................................75

690 ................................ Screwdriver Bits - PZD ..............................................................75

7 ..................................... Combination Spanners ............................................................11

7 ..................................... Combination Spanner Sets ....................................................11

702 ................................ Feeler Gauge Set - Fan Pattern ............................................106

7112 ............................. Open End Fitting ......................................................................178

7118 ............................. Open End Fitting ......................................................................178

7212 ............................. Ring End Fitting ........................................................................178

7218 ............................. Ring End Fitting ........................................................................178

7412 ............................. Ratchet Head ............................................................................179

7418 ............................. Ratchet Head .............................................................................179

753 ................................ Dremometer - Mini Torque Wrench...................................167

754 ................................ Ratchet Head ............................................................................179

756 ................................ Torque Screwdriver .................................................................174

759 ............................... TSN Slipper Torque Wrench ..................................................168

760 .............................. Breaking Torque Wrench .......................................................171

761 ............................... TSP Slipper Torque Wrench ..................................................169

762 ............................... Slipping Torque Wrench ........................................................169

7R ................................. Ratchet Spanner Sets ...............................................................12

7R ................................. Ratchet Spanners .......................................................................12

8000 - A0-A4 .............. Circlip Pliers - External Straight .............................................88

8000 - A01-A41 ......... Circlip Pliers - External Bent ...................................................88

8000 - A5 ..................... Circlip Pliers - External Staright .............................................89

8000 - A51 .................. Circlip Pliers - External Bent ...................................................89

257

ARTICLE INDEX

PageArticle No.

ARTICLE INDEX

PageArticle No.

8000 - J0-J4 ................ Circlip Pliers - Internal Straight.............................................. 89

8000 - J01-J41 ........... Circlip Pliers - Internal Bent ....................................................89

8000 - J5 ...................... Circlip Pliers - Internal Straight.............................................. 90

8000 - J51 ................... Circlip Pliers - Internal Bent ....................................................90

8112 ............................. Round Nose Pliers ......................................................................81

8120 .............................. Flat Nose Pliers ............................................................................81

8132 .............................. Telephone Pliers - Straight...................................................... 82

8132AB ........................ Telephone Pliers - Angled .......................................................82

8133 .............................. Multiple Pliers..............................................................................83

8134 .............................. Installation Pliers ......................................................................105

8135 ............................ Telephone Pliers .........................................................................82

8136 .............................. Mechanic’s Pliers ........................................................................83

8146 .............................. Wire Stripping Pliers .................................................................86

8147 .............................. Heavy Duty Cable Stripping Tool .........................................86

8148 ............................. Stripping Tool for Data Cable ................................................86

8178 ............................ Bolt Cutters ..................................................................................96

8178 ............................ Bolt Cutter Spares ......................................................................96

8200 .............................. Torque Angle Indicator ..........................................................167

8220 ............................. Universal Puller with Twin Grip ...........................................197

8250 ............................. Combination Pliers - Heavy Duty .........................................79

8260 .............................. Fencing Pliers ..............................................................................79

8276 ............................. Balance-Weight Pliers .............................................................105

8301 / 8302 ............... Dial Measuring Torque Wrench ...........................................173

8316 ............................. Side Cutters - American Pattern ........................................... 80

8320 JL......................... Wire Rope Cutters ......................................................................85

8340 / 8340Z ............. Mini Bolt Cutters.........................................................................96

8380 .............................. Tower Pincers ..............................................................................81

8381 .............................. Pincers ............................................................................................81

8516 .............................. Tin Snips - Scissors Pattern .....................................................97

8531 .............................. Tin Snips - Straight Pattern .....................................................97

8551 .............................. Bolt Extractor Set .....................................................................202

8554 .............................. Dremometer Torque Wrench ...............................................164



8562 .............................. Puller - Twin Grip ......................................................................197


8563 .............................. Puller - Triple Grip ....................................................................197

8563 D & DR ............... Dremometer Torque Wrench ...............................................165

8564 ............................. Puller - Twin Grip ......................................................................198



8566 .............................. Puller - Twin Grip ......................................................................198


8568 .............................. Puller - Twin Grip .....................................................................198






8600 .............................. Stud Extractor ...........................................................................200

8601 .............................. Ball Pein Hammer.....................................................................142

8612 ............................ Torque Calibration Analyser .................................................175

8612 ............................ Electronic Tester .......................................................................175

8612-3150 ................. Electronic Tester .......................................................................175

8801 .............................. Torque Wrench ..........................................................................172

907 ................................ Fender Protector ......................................................................108

95 ................................... Flat Cold Chisel .........................................................................142

95 HS ............................ Flat Cold Chisel & Hand Guard ............................................142

96 ................................... Cross-Cut Chisel........................................................................142

96 HS ............................ Cross-Cut Chisel & Hand Guard ..........................................142

99 ................................... Drift Punch .................................................................................143

920 ................................ Work Gloves ...............................................................................111

10002 ........................... Merchandiser Display Unit ...................................................243

AApprentice Toolkits ................................................................................................212-219

Artisan’s Toolkits. ......................................................................................................222-231

ATB SE Adjustable Breaking Torque Wrench...........................................................171

Automotive Electrician’s Toolkit ..................................................................................217

BBrass Pump Oil Can ..........................................................................................................108

Breaker Torque Wrenches .....................................................................................170-171

CC19 ................................ Socket (MM) (AF) 1/2” ...............................................................42

C19 ................................ Socket Sets .............................................................................32-38

C32 ................................ Socket (MM) (AF) 3/4” ..............................................................50

C32 ................................ Socket Sets ...................................................................................48

Capture Sensor Capture Cable ....................................................................................177

Capture Display .................................................................................................................177

Capture Manager - PC Software .................................................................................176

Capture Sensor - Adapter ..............................................................................................177

Capture Sensor - ISO A Mount .....................................................................................177

Capture Sensor Plate ....................................................................................................177

Caravan Toolkit ..................................................................................................................113

Car Workshop Puller Kit ..................................................................................................205

Club Hammers ...................................................................................................................145

Construction Machinery Toolkit .........................................................................214/215

CS 10 Capture Sensor ....................................................................................................177

258


ARTICLE INDEX

PageArticle No.

ARTICLE INDEX

PageArticle No.

CS 1500 Capture Sensor .................................................................................................177

CS 2 Capture Sensor ........................................................................................................177

CS 250 Capture Sensor ...................................................................................................177

CS 50 Capture Sensor ....................................................................................................177

DD19 ............................... Socket (MM) (AF) 1/2” ...............................................................42

D19 ............................... Socket Sets .............................................................................32-38

D19L ............................ Extra Deep Socket Bi-hexagon.............................................. 43

D21 ............................... Sockets 1” ......................................................................................54

D21 EMU ..................... Socket Set 1” ................................................................................53

D30 ............................... Socket (MM) (AF) 3/8” ...............................................................29

D30FMZ ....................... Socket Set 3/8” ............................................................................28

D30HMZ ...................... Socket Set 3/8” ............................................................................28

D32 ............................... Socket (MM) (AF) ........................................................................50

D32 ............................... Socket Sets ...................................................................................48

DMK .............................. Dremaster Torque Wrench ....................................................161

DMSE ............................ Dremaster Torque Wrench ....................................................161

Dremaster Torque Wrenches ...............................................................................160-161

Dremometer Torqure Wrenches .........................................................................162-167

DVI-20L/Z & 28L/Z ... Dremoplus Torque Multiplier ..............................................191

DVV-13Z ..................... Dremoplus Torque Multiplier ..............................................193

DVV-540RS ................ Dremoplus Torque Multiplier ..............................................189

DVV-40Z & 40ZRS .... Dremoplus Torque Multiplier ..............................................187

DVV-60-130ZRS ........ Dremoplus Torque Multiplier ..............................................188

EE 142 A/10 .................. Spares - Screw & Nut .................................................................95

E 143 A/10 .................. Spares - Screw & Nut .................................................................95

E 145 A/10 .................. Spares - Screw & Nut .................................................................95

E 210 A ......................... Spares - Chain..............................................................................94

E 210 B ......................... Spares - Pair of Jaws ..................................................................94

E 225 A ......................... Spares - Frame .............................................................................93

E 225 B ......................... Spares - Knurl ..............................................................................93

E 225 C ........................ Spares - Hook ..............................................................................93

E 225 D ....................... Spares - Pin ...................................................................................93

E 225 EF ...................... Spares - Rivet & Spring .............................................................93

E 227 A ........................ Spares - Spring ............................................................................93

E 227 B ......................... Spares - Knurl ..............................................................................93

E 227 C ......................... Spares - Jaw & Pin ......................................................................93

E 227 D ........................ Spares - Hook ..............................................................................93

EE 62 A ......................... Spares - Jaws ................................................................................19

E 62 BCD ..................... Spares - Knurl/Pin/Spring........................................................ 19

E8000A ........................ Spares - Tips .................................................................................89

E8000J ......................... Spares - Tips .................................................................................90

E-8147 .......................... Spare Blade ..................................................................................86

E-8148 .......................... Spare Blade ..................................................................................86

E-8178 .......................... Replacement Cutting Head ....................................................96

Electrician’s Light Current Toolkit ...............................................................................224

Electrician’s Medium Current Toolkit .........................................................................225

Electrician’s & Refrigeration Mechanic’s Toolkit .....................................................218

Electrician’s Toolcase .......................................................................................................110

Electrician’s Toolset .................................................................................................153/229

Engineers Scriber ..............................................................................................................107

Engineers Square ..............................................................................................................106

EV 150/200 ................. Spares - Engineering Vice .....................................................129

EV150/200 .................. Engineering Vice ......................................................................129

FFarmer’s Toolkit .................................................................................................................226

GG-Clamps .............................................................................................................................108

General Artisan’s Toolkit .................................................................................................227

GED0130 ..................... Non-Sparking Combination Spanners .............................208

GED0130 ..................... Non-Sparking Combination Spanners Sets ....................208

GED035 ....................... Non-Sparking Hexagon Sockets 1/2”................................209

GED0360 ..................... Non-Sparking Reversible Ratchet 1/2” .............................209

GED042 ....................... Non-Sparking Extensions 1/2” ............................................209

GED410 ....................... Non-Sparking Swivel HAndles 1/2” ...................................209

GED0400 ..................... Non-Sparking Sliding T-Bar 1/2” .........................................210

GED0400 ..................... Non-Sparking Universal Joint 1/2” .....................................210

GED0430 ..................... Non-Sparking Socket Set 1/2” .............................................210

GED080 ....................... Non-Sparking Screwdriver Set ...........................................210

GED053 ....................... Non-Sparking Pipe Wrench ..................................................211

GED048 ....................... Non-Sparking Adjustable Wrenches .................................211

GED060 ....................... Non-Sparking Combination Pliers .....................................211

GED066 ....................... Non-Sparking Power Side Cutters .....................................211

HHSP ............................... Hydraulic Pressure Spindle ...................................................199

IIKS19 ............................ Allen Key Socket - Phillips & Pozzidriv Bits 1/2”............... 45

IKS20 ............................ Screwdriver Bit Socket 1/4” ....................................................26

IKS20 PZD ................... Screwdriver Bit Socket 1/4” ....................................................26

IN19 .............................. Allen Key Socket (MM) (AF) 1/2” ...........................................43

IN19 .............................. Allen Key Socket Sets .........................................................38-39

IN19L ............................ Extra Long Allen Key Socket 1/2” .........................................44

IN20L ............................ Screwdriver Bit Socket 1/4” ....................................................26

IN30 .............................. Allen Key Socket 3/8” ................................................................30

259

ARTICLE INDEX

PageArticle No.

ARTICLE INDEX

PageArticle No.

IN32 .............................. Allen Key Socket 3/4” ................................................................51

Industrial Puller Kit ...........................................................................................................205

INK19 ............................ Impact Allen Key Socket 1/2” .................................................59

INK21 ............................ Impact Allen Key Socket 1” .....................................................62

INK32 ............................ Impact Allen Key Socket 3/4” .................................................60

INR19L ......................... Allen Key Socket - Long Spline Ribe 1/2” ........................... 44

INX19 - INX19L .......... Allen Key Socket - Spline Bit 1/2” .........................................44

IS20 ............................... Screwdriver Bit Socket 1/4” ....................................................26

ITX19 ............................ Torx Allen Key Socket - Male 1/2” .........................................44

ITX19 ............................ Torx Allen Key Socket Set - Male 1/2” ................................. 39

ITX19B .......................... Torx Allen Key Socket - Male 1/2” .........................................45

ITX19L .......................... Long Torx Allen Key Socket - Male 1/2” .............................. 45

ITX20 ............................ Screwdriver Bit Socket 1/4” ....................................................26

ITX30 ............................ Torx Allen Key Socket - Male 3/8” .........................................30

ITX19/TX19 FMT ....... Torx Allen Key Socket Set - Male & Female ....................... 40

JJunior Hacksaw .................................................................................................................107

KK19 ................................ Impact Sockets 1/2” ..................................................................58

K19 ................................ Impact Socket Set ......................................................................58

K1900 ........................... Impact Driver ...............................................................................59

K1900 ........................... Impact Driver Set .....................................................................58

K19L .............................. Impact Socket .............................................................................58

K21 ................................ Impact Socket .............................................................................62

K21L .............................. Impact Socket - Long Pattern ................................................62

K32 ................................ Impact Socket .............................................................................60

K32L .............................. Impact Socket .............................................................................60

K37 ................................ Impact Socket .............................................................................63

KB1932 ........................ Impact Socket Converter ........................................................59

KB1970/75 .................. Safety Rings & Pins ....................................................................59

KB1990 ........................ Impact Extension .....................................................................59

KB1995 ........................ Impact Universal Joint .............................................................59

KB2132 ........................ Impact Socket Reducer ............................................................62



KB2190 ........................ Impact Extension .......................................................................63










KD-26R ......................... Tubular Box Spanner Set .......................................................100

MMechanic’s Toolkit ............................................................................................................216

Merchandiser Concepts ........................................................................................240-242

MV 100/150 ............... Spares - Mechanic’s Vice .......................................................129

MV 100/150 ............... Mechanic’s Vice .........................................................................129

NNon-Spark Range ....................................................................................................206-211

PPA Starter Pack ...................................................................................................................130

Pegboard Accessories ....................................................................................................130

Precision Engineering Tolls ...........................................................................................106

RREF 10SD .................... 10 ScrewdriverAssortment ...................................................138

REF A ............................ C19/22 Assortment .................................................................136

REF B ............................. C19 Assortment ........................................................................136

REF C ............................ 1B Assortment ..........................................................................136

REF D ............................ C19/IN19 Assortment .............................................................136

REF E ............................. 1B/62H Assortment .................................................................137

REF F ............................. D19/ACC/SKT Assortment ....................................................137

REF G ............................ C32/6 Assortment ....................................................................137

REF H ............................ D19/22/ACC Assortment .......................................................137

REF I .............................. D19 Assortment .......................................................................137

REF J ............................. D19/IN19 Assortment ............................................................137

REF K ............................. D32/6 Assortment ...................................................................138

REF L ............................. PL/137/36 Assortment ...........................................................138

REF MF ......................... PL/81/82/83 3 Pliers Assortment ........................................138

REF M ........................... PL/81/82/83 3 Pliers Assortment ........................................138

REF N-10 ..................... 10 ScrewdriverAssortment ...................................................138

REF O ........................... 6 Screwdriver Assortment ...................................................139

REF OF ......................... 6 Screwdriver Assortment ...................................................139

REF P ............................ 4 EXT - T/BAR Assortment .....................................................139

REF PF ......................... 4 Extension+T/Bar Assortment ...........................................139

REF Q ........................... 4 ACC - POWER BAR Assortment .......................................139

REF QF.......................... 4 Acc+Power Bar Assortment ..............................................139

REF RF .......................... C19/Z94 Assortment...............................................................139

REF SF .......................... 1B/145 Assortment .................................................................139

REF VF ......................... Ph&Stubby Screwdriver Assortment ................................138

REF WF ........................ Mec&Elec Screwdriver Assortment ...................................138

260

TECHNOLOGY AND SAFETYARTCILE INDEX

ARTICLE INDEX

PageArticle No.

ARTICLE INDEX

PageArticle No.

RL-DVV13 .................... Reaction Arm .............................................................................193

RL-DVV-60-80 ............ Reaction Arm .............................................................................188

RL-DVI 20/28 .............. Reaction Arm .............................................................................191

RL-DVV40 ................... Reaction Arm .............................................................................187

SS8000 ........................... Circlip Pliers Set ..........................................................................90

S8003 JC ..................... Pliers Set ........................................................................................84

S8140 A ....................... Crimping Pliers Set - Automotive ......................................... 87

S8140 D ....................... Crimping Pliers Set - Data Com............................................. 87

S8140 E ........................ Crimping Pliers Set - Electronics ...........................................88

S8140 J ........................ Crimping Pliers Set - Industustrial .......................................88

S8303 JC ...................... Pliers Set ........................................................................................85

Sortimo General Tool Assortment ....................................................................112/236

Safety Glasses & Bag ....................................................................................................108

Screwdriver Display Unit ...............................................................................................243

Sledge Hammers ..............................................................................................................145

Slipper Torque Wrenches ......................................................................................168-169

Small Leisure Boat Toolkit ..............................................................................................112

SR - C19Z-10 Socket Set ...................................................................................................32

SR - D19Z-10 Socket Set ...................................................................................................32

SR - IN19 PM-6 Allen Key Socket Set ............................................................................ 38

SR - IN19 PM-9 Allen Key Socket Set ............................................................................ 39

SR - ITX19 MT Torx Socket Set ........................................................................................39

SR - TX19 FT Torx Socket Set ...........................................................................................40

Steel Ruler ...........................................................................................................................106

TTBN Breaking Torque Wrench ......................................................................................171

Technician’s Rucksack Toolkit .......................................................................................228

TLS PRO Preset Torque Screwdriver ...........................................................................174

Tool Bags & Rucksacks ....................................................................................................110

Tool Jacket ..........................................................................................................................111

Torco�x Torque Wrenches ....................................................................................158-159

Torque Secrewdrivers ....................................................................................................174

TSC Slipper Torque Wrench ...........................................................................................169

TT3KH 350 ................. Torcotronic III Electronic Torque Wrench .........................172

TX19 ............................. Torx Socket - Female 1/2” ........................................................45

TX19 ............................. Torx Socket Set - Female 1/2” ................................................40

TX30 ............................. Torx Socket - Female 3/8” ........................................................30

TX4 ................................ Flat Ring Spanner .......................................................................15

VV 4614 PLUS .............. Voltage Tester ............................................................................152

V 62 .............................. Adjustable Wrench ..................................................................149

VB19E .......................... C19 Socket Set ..........................................................................243

VB19E .......................... D19 Socket Set ..........................................................................243

VB19E ........................... Socket Display Box ..................................................................243

VDE 2160 PH ............. Phillips Screwdriver .................................................................149

VDE 2170 ................... Electrician’s Screwdriver ........................................................149

VDE 2133 .................... Nut Driver ...................................................................................148

VDE 2133 .................... Nut Driver Set ............................................................................148

VDE 2E ......................... Single Ended Spanner ............................................................148

VDE 4507 .................... Torque Wrench ..........................................................................149

VDE 4522 .................... Cable Knife .................................................................................152

VDE 8098 H ................ Stripping Pliers..........................................................................150

VDE 8099 H ................ Stripping Pliers .........................................................................151

VDE 8120 H ................ Flat Nose Pliers .........................................................................151

VDE 8122 H ................ Round Nose Pliers ....................................................................151

VDE 8132 H ................ Telephone Pliers .......................................................................152

VDE 8132AB H ........... Telephone Pliers - Angled .....................................................151

VDE 8250 H ................ Combination Pliers ..................................................................150

VDE 8314 H ................ Side Cutters ................................................................................150

VDE 8316 H ................ Side Cutters - American Pattern .........................................150

VDE 894 ...................... Single Open Ended Spanner................................................148

VDE 2160-2170 ......... Screwdriver Set .........................................................................149

261

ACCREDITATIONACCREDITATION

262

TECHNOLOGY AND SAFETYACCREDITATION

263

264

TECHNOLOGY AND SAFETYACCREDITATION

WarrantyIn terms of GEDORE’S warranty policy, all torque wrenches are covered by a lifetime guarantee against defective materials and workmanship. Provided that the tool has been correctly used for its intended purpose and allowances have been made for the wear and tear of moving parts, the torque wrench will be repaired free of charge.



CalibrationA standard calibration and the issue of a test certi�cate will be provided as standard practice on any repair conducted.

A SANAS calibration and the issue of a SANAS calibration certi�cate will be done on request at a nominal charge.

ObsolescencePlease note that while GEDORE uses its best endeavours to carry signi�cant stocks of spares to support its torque wrench product range, some spares for older discontinued items are no longer available. In such cases, repair of the torque wrench may not be possible.

“Our guarantee covers all tools against breakage under normal working conditions and is subject to fair wear and tear.”

At GEDORE we take pride in the quality of our products and services and we review all warranty claims with the aim of using the information gained for further product improvement.

Every GEDORE tool is covered by a lifetime guarantee against defective material and workmanship. Provided that the tool has been used correctly for its intended purpose and allowances have been made for wear and tear, this guarantee will allow for the repair or exchange of the tool.

While some deterioration through extensive use might be unavoidable, we will adopt a generous approach when viewing warranty claims. We do, however, set warranty limitations on wear and tear, obvious misuse, missing parts and purposely altered tools to protect ourselves against unreasonable claims.

Should the product fall outside the parameters of the warranty criteria, we will advise the customer on the repair or replacement cost of the article.

© Copyright by Gedore Tools SA (Pty) Ltd.

Gedore strives to be the leading supplier of superior quality tools in Africa and other designated markets.

We seek to build and maintain lasting relationships with customers by responsively o�ering suitable products at fair prices, which consistently conform to the highest level of product and service quality standards.

We strive to increase the value for all stakeholders and to be a preferred supplier, employer and customer.

Quality We strive to be the best that we can be in everything that we do.

Innovation and Knowledge We strive for continuous improvement in all aspects of our business through learning, benchmarking and having a general uneasiness with the status quo.

Responsiveness We have a bias for action by feeling a sense of urgency in everything that we do, and encourage employees to be proactive.

Team Work and Mutual Respect We encourage and support team participation, e�ective communication and mutual respect.

Motivation and People Centred We acknowledge that our employees are the key to our success.

We motivate employees by providing opportunities for advancement, sharing information, fair treatment, training, job security and workplace safety.

Customer Focused We expect all employees to maintain a customer focus in all aspects of their work.

Care for the EnvironmentWe are sensitive of the need to care for the environment and apply ourbusiness processes accordingly.

Corporate Governance We enforce good corporate governance by encouraging honesty, transparency, trust, equity and social responsibility.

DISCLAIMER

As we are constantly improving our products, we reserve the right to make changes as we deem necessary. The actual products delivered may therefore vary from those depicted in the catalogue.We do not provide any warranties in connection with technical and safety information provided in this catalogue. All customers are therefore advised to refer directly to their manufacturer’s speci�cations and the advice and standards of the relevant professional/trade associations. All products remain the property of Gedore Tools SA (Pty) Ltd until paid for in full.We cannot accept any liability for printing errors. Reproduction of any part of this catalogue requires the prior written permission of Gedore Tools SA (Pty) Ltd. All rights reserved worldwide.

GEDORE TOOLS SA WARRANTY POLICY

TORQUE WRENCH WARRANTY &

CALIBRATION POLICY

MISSION STATEMENT

VALUE SYSTEM

TOTALRANGE

TO

TA

LR

AN

GE

17 1

8

HEAD OFFICE & FACTORY

NATIONAL NUMBER

0861-GEDORE (0861-433673)

Durban (Latitude: 29.799364 Longitude: 30.880337)

103 Qashana Khuzwayo Road, New Germany, 3610PO Box 68, New Germany, 3620Tel: +27 (0)31 705-3587Fax: +27 (0)31 705-3277Email: [email protected] / [email protected]: www.gedore.co.za

SALES OFFICESJohannesburg (Latitude: 26.078448 Longitude: 28.117125)

26 Village Crescent, Linbro Business ParkPO Box 72, Linbro Park, 2065Tel: +27 (0)11 608-5959Fax: +27 (0)11 608-2953

Cape Town (Latitude: 33.875969 Longitude: 18.500760)

No. 8 Woodbridge Business Park, Koeberg Road, MilnertonPO Box 37299, Chempet, 7442Tel: +27 (0)21 529-6360Fax: +27 (0)21 552-8397 17

18

www.gedore.co.za

catalogue.pdf - Gedore South Africa

Documents