01/16/22 1 WORLD UNIVERSITY o f B a n g l a d e s h
04/17/23 1
WORLD UNIVERSITY
o f B a n g l a d e s h
04/17/23 2
welcome to our presentation
04/17/23 3
Project Report on…………….
ANALYSIS OF SHEAR WALL
DUE TO
LATERAL LOAD
04/17/23 4
Supervisor:
Ahmed Shiblee NomanAsst. ProfessorDept. of Civil EngineeringWorld University of Bangladesh
Project Work Done By:
MD. ABDUL BATEN MD. ABUL KASHEM MD. ZAHIRUL HOQUE RANZU AHMED & MD. MASUD RANA
04/17/23 5
Introduction:
High rise building is a structure vertically cantilevered from the ground level subjected to axial loading and lateral forces.
Lateral forces generated either due to wind blowing against the building or due to the inertia forces induced by ground shaking.
For building taller than ten stories, frame action obtain by the interaction of slabs and columns is not adequate to give the required lateral stiffness.
However it can be improved by statically placing shear walls as it very effective in maintaining the stability of tall buildings under severe wind or earthquake loading.
04/17/23 6
ABSTRACT
The purpose of this study is to model and analyze the non planar shear wall assemblies of shear wall-frame structures.
These models are based on conventional wide column analogy.
For modeling closed section shear walls, in addition to this the torsional stiffness of the wide columns are adjusted by using a series of equations.
Shear wall systems having different shapes of wall-frame & Flat Plate shear wall assemblies are analyzed by static lateral load
04/17/23 7
Objectives:
To carry out a frame analysis on shear wall models using ETABS non linear version 8.5 software.
To check the reliability of frame analysis method compare to wall frame shear wall and flat plate shear wall.
The study is focused on the determination of the ultimate lateral load due to wind and earthquake.
To find out and compare the different calculated value of those wall frame and flat plate shear wall structures.
To draw few recommendations based on the study.
04/17/23 8
Scope of the Study :
The main intention of the research work presented in this thesis is to study the majority of the high rise building structures in Bangladesh have shear wall-frame systems.
The study is to model and analyze shear wall-frame structures having non-planar shear walls.
Proper analysis and design of building structures that are subjected to static and dynamic loads is obtaining acceptable accuracy in the results.
04/17/23 9
Shear wall system:
Shear walls have been the most common lateral force resisting
elements for tall building besides frame
system.
04/17/23 10
Monolithic shear wall can be classified as short, squat or cantilever as shown in figure according to there
height/depth ratio.
Shape of Shear Wall
04/17/23 11
Method of Analysis of Shear wall
structures
Analysis on shear wall structures can be made in thefollowing three types of methods
Finite Element Analysis (FEA) Continuous connection method (CCM): Equivalent Frame Analysis (EFA)
This manual presents a set of simple building systems thathave been analyzed using ETABS Version 8.5 software.
04/17/23 12
modeling of shear walls
Shear wall models in the literature can be divided into two:
1. Models developed for elastic analysis of building structures.
2. Models developed for nonlinear analysis of building structures.
04/17/23 13
Open Section Shear Walls
It is a common assumption that due to the highin-plane stiffness of floor slabs, open sectionshear walls can be considered as thin-walled
beams of non-deformable contour
04/17/23 14
Fig: Open Section Shear Wall
04/17/23 15
Fig: Open Section Shear Wall
04/17/23 16
04/17/23 17
04/17/23 18
0
5000
10000
15000
20000
25000
30000
35000
40000
EQ-X EQ-Y
Plate
Column
Axis (X, Y)
Comparative values of Base Moment due to Lateral Load
04/17/23 19
0
200
400
600
800
1000
1200
1400
1600
WIND-X WIND-Y
Plate
Column
Axis (X, Y)
04/17/23 20
Conclusion:
▶ Analyzed of Plate shear wall and column shear wall structures find base moment values are very closed.
▶ According to analysis of two methods that we get more accurate results in frame method as a alternate for plate element method.
▶ The frame element method is more economical and memory efficient.
▶ Frame analysis method is very simple rather than plate element method.
04/17/23 21
Recommendation:
◊ The study is used for building structure, but it also be used in Bridge structure.
◊ We have done this method by static analysis, but dynamic analysis should also be performed.
04/17/23 22
Special Thanks
04/17/23 23
04/17/23 24