IMPORTANT READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS CAUTION 1. Read these instructions and rules careully. Failure to ollow them could cause serious body injuries and/or property damages. 2. Check your local electrical saety and plumbing codes. The installation must comply with these guidelines. 3. No modifcations, additio ns or deletions should be made to the blower without actory approval. 4. Do not relocate blower without prior app roval rom the actory. 5. Ensure that a class A ground ault interrupter (G.F .I.) is installed as part othe wiring. 6. Wiring should be permanent . Do not use an extension cord. Have the electrical part othe installation done by, or approved by, a qualifed electrician. 7. The blower has no serviceable parts. INSTALLATION Air massage bathtub installation 1. Never handle your air massage bathtu b by the piping. 2. Do not rest your bath unit on the jets located underneath the bathtub. Make sure that back jets are adequately protected when entering the unit into your bathroom. Be careul not to hit a wall or door rame with the back jets. IMPORTANT An ac cess panel o30" x 15" (75cm x 40cm) must be located near the blower to allow easy ser vicing ineed be. Final installation 1. IMPORTANT: The blower must not be insulated and must have sucient air space to permit proper unctioning. Surrounding air should be able to reach the room under the apron or the podium oyour bathtub. 2. Iactory installed, the optio nal heating element on your air massa ge system heats the air blown into the bathtub or the comort othe customer. It will not, under any circumstances, reheat or maintain the temperature othe bath water . 3. Area underneath and around the bath tub must be cleaned beore fnalizing the installation to ensure that no wood shavings or other particles enter into the air blower and are blown through the jets. 4. Beore flling with water, clean bathtub rom installation debris and d irt. Inecessary use a vacuum cleaner. 5. Veriy connection and unctio ning otouch pad and air blower beore fnalizing the installation. AIR MASSAGE SYSTEM Introduction Thank you or your confdence in CG Air Systèmes inc. by purchasing your new air massage system. We can assure you that CG Air Systèmes inc. uses the best materials and applies the most strict quality control measures to ensure that each and every unit meets the highest standards othe Canadian Standard Association (CSA) and Underwriters Laboratories (UL). The origins oAir Massage... Air massage, also known as balneotherapy , is the use oair mixed with water to gently but eciently massage the body. Its soothing and pain relieving virtues were already recognized by the Romans. But, unlike the Romans who could only aord the pleasures oa relaxing and invigorating bath every now and then, the technology developed by CG Air Systèmes inc. allows you to enjoy the benefts obalneotherapy every day in your own bathroom. Sae use oyour air ma ssage batht ub Your new massage system provides you with a gentle, overall massage. The m assage eect is o btaine d by inject ing w arm a ir t hrough air j ets i nto the bathwater . Using the blower or too long a period at too high water temperature will cause a tiring eect. When you frst begin to use your luxury bath unit, set the blower duration at fve minutes maximum. Regulate the water temperature to a moderately warm level. These levels can be later increased or additional massaging eects. Your physiological response to a hot massage bath depends on your age, health and medical history. Iyou develop a headache or become dizzy or nauseous, get out at once and cool ounder the shower . Get medical help ithe symptoms persist. Consult your doctor beore you use the massage bath or physical therapy oan injury or disorder . Do not take a massage bath without your doctor’s consent iyou are ill, pregnant or iyou suer rom high blood pressure, heart disease or other health problems. Never take a massage bath while under the inuence omedication, drugs or alcohol. C aut ion: Children or incapacitade d people should not use the massage bath unattended. Your bath water temperature should not exceed 40ºC (104ºF). Ater having cleaned the tub rom all installation debris and dirt, fll with water at normal bathing water level ie. maximum 2” below the overow when bather is sitting in the tub. Never fll the tub with water above the overow level. When flling your tub make sure that water temperature does not exceed 70ºC (158ºF). The use owater that is too hot might shorten the lietime othe o’rings and gaskets othe air jets. TROUBLESHOO TING Blower ails to operate 1. Veri y that electronic touch control is connected properly (Reer to wiring diagram). 2. Check electric power supply . Reset circuit breaker or replace use inecessary. 3. Check ground ault circuit interrupter . Reset itripped. 4 Ithe system has been unctioning or quite some time, it is possible that the thermic protection has shut othe motor. Let it cool oor at least 30 minutes beore using it again. Motor runs, but no air c omes through the jets 1. Veriy that the main air hose rom mani old to blower is properly connected. Inecessary, reconnect and tighten clamps. Air outl ets of et heads are obst ruded 1. Ithe air outlets oa jet head are obstructed by soap or o ther residues, fll tub with warm water, then switch system ON and OFF several times. The air outlet s should be cleared, ithis is not sucient, careully tap on the jet heads with the handle oa screw driver or a similar tool (plastic) while the blower is running. The air heater seems not to work1. To veriy the operation othe air heater , fll the bathtub to working level and operate blower on high turbulence or approximately 5 minutes. Careully eel the exible connection hose where it connects to the blower. The hose and its immediate area should eel warm to the touch. Inot, contact your local distributor. 2. Iyour tub is installed against two outside walls, it is recommended to ensure adequate insulation or these outside walls to minimize heat loss. 3. Skin sensitive peopl e might experience the so-called “cold air eect ” which is caused by the sensation oair bubbles running along the wet skin and providing the bather with a shivering sensation. Just move your body slightly away rom the closest jet to stop the sensation ocold air. (NOTE : Even ithe outcoming air would be hot enough to burn the skin, this shivering eect would still persist.) Note: The air heater is not designed to heat your bath water, just to preheat the incoming air to body temperature. The drying cycle 1. Veriy with our elect ronic control instruction s. For blower models MILLENIUM: ME · ME-LL · M0 · M0-LL · M3 · MAS · MAST · MS PIGGY: PE · P0 · P3 · PAS · PAST MILLENIUM & PIGGY 1000 _ 10-JANV.-2005
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
1. Read these instructions and rules careully. Failure to ollow themcould cause serious body injuries and/or property damages.
2. Check your local electrical saety and plumbing codes. Theinstallation must comply with these guidelines.
3. No modifcations, additions or deletions should be made to the blowerwithout actory approval.
4. Do not relocate blower without prior approval rom the actory.
5. Ensure that a class A ground ault interrupter (G.F.I.) is installed as parto the wiring.
6. Wiring should be permanent. Do not use an extension cord. Have theelectrical part o the installation done by, or approved by, a qualifed
electrician.
7. The blower has no serviceable parts.
INSTALLATION
Air massage bathtub installation
1. Never handle your air massage bathtub by the piping.
2. Do not rest your bath unit on the jets located underneath the bathtub.Make sure that back jets are adequately protected when entering the
unit into your bathroom. Be careul not to hit a wall or door rame withthe back jets.
IMPORTANT
An ac cess panel o 30" x 15" (75cm x 40cm) must be
located near the blower to allow easy servicing i need be.
Final installation
1. IMPORTANT: The blower must not be insulated and must have sucient
air space to permit proper unctioning. Surrounding air should beable to reach the room under the apron or the podium o your bathtub.
2. I actory installed, the optional heating element on your air massagesystem heats the air blown into the bathtub or the comort o the
customer. It will not, under any circumstances, reheat or maintain
the temperature o the bath water.
3. Area underneath and around the bathtub must be cleaned beore
fnalizing the installation to ensure that no wood shavings or otherparticles enter into the air blower and are blown through the jets.
4. Beore flling with water, clean bathtub rom installation debris and dirt.I necessary use a vacuum cleaner.
5. Veriy connection and unctioning o touch pad and air blower beore
fnalizing the installation.
AIR MASSAGE SYSTEM
Introduction
Thank you or your confdence in CG Air Systèmes inc. by purchasing
your new air massage system.We can assure you that CG Air Systèmes inc. uses the best materials and
applies the most strict quality control measures to ensure that each andevery unit meets the highest standards o the Canadian Standard
Association (CSA) and Underwriters Laboratories (UL).
The origins o Air Massage...
Air massage, also known as balneotherapy, is the use o air mixed with
water to gently but eciently massage the body.
Its soothing and pain relieving virtues were already recognized by the
Romans. But, unlike the Romans who could only aord the pleasures o a relaxing and invigorating bath every now and then, the technology
developed by CG Air Systèmes inc. allows you to enjoy the benefts o
balneotherapy every day in your own bathroom.
Sae use o your air massage bathtub
Your new massage system provides you with a gentle, overall massage.
The massage eect is obtained by injecting warm air through air jets intothe bathwater. Using the blower or too long a period at too high water
temperature will cause a tiring eect. When you frst begin to use yourluxury bath unit, set the blower duration at fve minutes maximum.Regulate the water temperature to a moderately warm level. These
levels can be later increased or additional massaging eects.
Your physiological response to a hot massage bath depends on your
age, health and medical history. I you develop a headache or becomedizzy or nauseous, get out at once and cool o under the shower. Get
medical help i the symptoms persist.
Consult your doctor beore you use the massage bath or physicaltherapy o an injury or disorder. Do not take a massage bath without your
doctor’s consent i you are ill, pregnant or i you suer rom high bloodpressure, heart disease or other health problems. Never take a massage
bath while under the inuence o medication, drugs or alcohol.
C a ution: Children or incapacitaded people should not use the massage
bath unattended. Your bath water temperature should not exceed 40ºC
(104ºF).
Ater having cleaned the tub rom all installation debris and dirt, fll withwater at normal bathing water level ie. maximum 2” below the overowwhen bather is sitting in the tub. Never fll the tub with water above the
overow level.
When flling your tub make sure that water temperature does not exceed
70ºC (158ºF). The use o water that is too hot might shorten the lietime
o the o’rings and gaskets o the air jets.
TROUBLESHOOTING
Blower ails to operate
1. Veriy that electronic touch control is connected properly
(Reer to wiring diagram).
2. Check electric power supply. Reset circuit breaker or replace use i
necessary.
3. Check ground ault circuit interrupter. Reset i tripped.
4 I the system has been unctioning or quite some time, it is possible
that the thermic protection has shut o the motor. Let it cool o or atleast 30 minutes beore using it again.
Motor runs, but no air comes through the jets
1. Veriy that the main air hose rom maniold to blower is properly
connected. I necessary, reconnect and tighten clamps.
Air outlets of et heads are obstruded
1. I the air outlets o a jet head are obstructed by soap or other residues,
fll tub with warm water, then switch system ON and OFF several times. The air outlets should be cleared, i this is not sucient, careully tap
on the jet heads with the handle o a screw driver or a similar tool(plastic) while the blower is running.
The air heater seems not to work
1. To veriy the operation o the air heater, fll the bathtub to working level
and operate blower on high turbulence or approximately 5 minutes.
Careully eel the exible connection hose where it connects to theblower. The hose and its immediate area should eel warm to the
touch. I not, contact your local distributor.
2. I your tub is installed against two outside walls, it is recommended to
ensure adequate insulation or these outside walls to minimizeheat loss.
3. Skin sensitive people might experience the so-called “cold air eect”
which is caused by the sensation o air bubbles running along the wetskin and providing the bather with a shivering sensation. Just move
your body slightly away rom the closest jet to stop the sensation o cold air. (NOTE: Even i the outcoming air would be hot enough to burn
the skin, this shivering eect would still persist.)
Note: The air heater is not designed to heat your bath water, just to
preheat the incoming air to body temperature.
The drying cycle
1. Veriy with our electronic control instructions.
For blower models
MILLENIUM: ME · ME-LL · M0 · M0-LL · M3 · MAS · MAST · MS PIGGY: PE · P0 · P3 · PAS · PAST
All air blowers are warranted to be ree o deects in manuacturing,material and workmanship or a period o one year rom the date o purchase by the owner/end-user.
Limitations
This warranty does not apply to the bath tub and/or spa but solely tothe components manuactured by CG AIR SYSTÈMES INC.
This warranty shall not apply to the ollowing incorrect operatingprocedures, breakage or damages caused by ault, abuse, misuse,carelessness, misapplication, alteration, modifcation, impropermaintenance o the unit, as well as act o God, fre, chemical or naturalcorrosion or any other casualty.
The owner o the product covered by the present warranty is entirelyresponsible or the proper installation o the product in accordance withthe installation manual provided. CG AIR SYSTÈMES INC. neither installsnor supervises nor contracts or the installation and consequently cannotbe held responsible or the installation.
CG AIR SYSTÈMES INC. is not responsible or any damages or claimsresulting rom deects that could have been discovered, repaired oravoided by inspection and testing prior to installation.
CG AIR SYSTÈMES INC. makes no express warranty , no warranty ormerchantability, no warranty o ftness or particular purposes, neitherany other warranty implied or statutory or its products other thanspecifed above.
In no event shall CG AIR SYSTÈMES INC. liability exceed the purchaseprice o the deective part.
I within the warranty period, any such product shall prove to bedeective, CG AIR SYSTÈMES INC. reserves the right to repair or replacethe deective product with one o equal value.
Commercial limitations
In addition to the above conditions and limitations, i the product is tobe used as a display, the warranty period begins when the product hasbeen placed on display. Under no circumstances willCG AIR SYSTÈMES INC. be responsible or any proft loss due to amalunction o the unit. This warranty gives the owner/end-user specifc
ME · ME-LL · MO · MO-LL · PE · PO AIR BLOWERS
legal rights and the owner/end-user may have other rights which varyrom one state/province to another.
CG AIR SYSTÈMES INC. reserves the right to discontinue and/or changemodels, colors and specifcations in design together with replacementparts without notice and without incurring any obligations.
ELECTRICAL INSTALLATION
1. The electrical installation is subject to inspection and approval bylocal authorities. All electrical connections must be made by alicensed electrician.
2. Beore beginning installation make sure that electric power is
disconnected at use box.3. The blower must be located out o reach rom the person in the
bathtub and fxed in position with screws.4. The blower connection is pre-installed. Do not remove the blower
cover, this will void the warranty.
5. Reer to your local electrical code i your distance between theinstallation site o the bath unit and the main use box is more than100 eet (30,4 m).
120V Use the actory pre-installed type SJ wire to connect to junctionbox (not provided by the tub manuacturer). Run a separate120V, 60Hz, 15A G.F.I. (Class A protected) electric circuit rom the mainuse box to the junction box. Use a 14 gage three conductor cable(2 wires plus ground) in connections up to 100 eet (30,4m) rom themain use box.
240V Use the actory pre-installed type SJ wire to connect to junction
box (not provided by the tub manuacturer). Run a separate240V, 60Hz, 15A G.F.I. (Class A protected) electric circuit rom the mainuse box to the junction box. Use a 14 gage three conductor cable(2 wires plus ground) in connections up to 100 eet (30,4m) rom themain use box.
FUNCTIONS ME · ME-LL · PE
This blower can be operated by an independent electronic control, air switch or wall timer.
One speed or multispeed depending o the control model. Please reer to the instructions o the electronic control, air switch or wall timer or theoperation o your air system.
FUNCTIONS MO · M0-LL · PO
Your blower is equipped with an integrated air heating element.
This blower can be operated by an independent electronic control, air switch or wall timer.
One speed or multispeed depending o the control model. Please reer to the instructions o the electronic control, air switch or wall timer or theoperation o your air system.