-
ELEMEN MESIN(RI.1232)
Dosen:Fahmi Mubarok, ST., MSc.Metallurgy LaboratoryMechanical
EngineeringITS- Surabaya2008
SambunganSambungan Las
Analisa dan PerhitunganApplikasi
LECTURE IV & VLECTURE IV & V
http://www.its.ac.id/personal/material.php?id=fahmi
-
Fahmi Mubarok
IV 2Mech. Eng. Dept. ITS Surabaya
Elemen Pengikat (Fasteners, Connectors, Joints): Introduksi
Fasteners
Permanent Detachable
Rivets
Weldments
Metal Stitching
Bolts
Cotter Pins
Keys
Snap Rings
Sambungan permanen: sambungan yang rusak bila dilepas. Sambungan
detachable : sambungan yang dapat digunakan atau dilepas se-
waktu-waktu tanpa merusak sambungan itu sendiri.
-
Fahmi Mubarok
IV 3Mech. Eng. Dept. ITS Surabaya
Sambungan Las: Apliklasi
-
Fahmi Mubarok
IV 4Mech. Eng. Dept. ITS Surabaya
WeldingWhat is welding?Welding is a fusion process, in which
metal parts are heated to the melting point and fused together,
usually with a filler of the same material melted along with the
parent material.
Temperaturecontrol is themost importantparameterassociated with
obtaining agood weld.
-
Fahmi Mubarok
IV 5Mech. Eng. Dept. ITS Surabaya
Welding
Welding is a very efficient way of joining metals
Welding is labour intensive In a welded structure subject to
fluctuating loads, the strength of the welds determine the
strength of the structure
It is important to select the right weld type for the right
job
Will perform its intended functionWill have the desired
reliability & safetyIs capable of being constructed fabricated
inspected transported assembledHas minimum cost
Basic Weld Design ObjectivesAdvantages
-
Fahmi Mubarok
IV 6Mech. Eng. Dept. ITS Surabaya
Modern Welding Processes
-
Fahmi Mubarok
IV 7Mech. Eng. Dept. ITS Surabaya
Arc Welding
Electric current flowing through ahigh resistance air gap
generates anintense arc with temperatures rangingfrom 6,000 to
10,000 oF.
Arc welding is themost commonmethod used withstructural
steelwelding.
Arc Welding Instructions for the Beginner, Lincoln Arc Welding
Foundation, Fig. 9&13
-
Fahmi Mubarok
IV 8Mech. Eng. Dept. ITS Surabaya
Metode Pengelasan: Arc Welding
Shielded Metal-Arc-Welding Process
-
Fahmi Mubarok
IV 9Mech. Eng. Dept. ITS Surabaya
Metode Pengelasan: Arc Welding
Submerged Arc-Welding Process
-
Fahmi Mubarok
IV 10Mech. Eng. Dept. ITS Surabaya
Metode Pengelasan: Arc Welding
Flux-Cored Arc-Welding Process
-
Fahmi Mubarok
IV 11Mech. Eng. Dept. ITS Surabaya
Metode Pengelasan: Arc Welding
Plasma-Arc-Welding Processes
-
Fahmi Mubarok
IV 12Mech. Eng. Dept. ITS Surabaya
MIG or GMAW
Argon and CO2 are common inert gases used in the MIG process. A
mixture of 75% Argon and 25% CO2 (C-25) is also very common.
Continuously fed filler wire makes MIG welding suited to high
volume, machine assisted industrial welding applications.
-
Fahmi Mubarok
IV 13Mech. Eng. Dept. ITS Surabaya
TIG or GTAW
The shielding gas in the TIG process is Helium. This gives rise
to the term heli-arc welding.
The TIG process is considered the most precise, most
controllable, and cleanest method of welding.
The TIG process can be used to make welds of great strength and
quality in thin, light, and dissimilar materials.
-
Fahmi Mubarok
IV 14Mech. Eng. Dept. ITS Surabaya
Sambungan Las: Metode Pengelasan
Electrogas-WeldingProces
-
Fahmi Mubarok
IV 15Mech. Eng. Dept. ITS Surabaya
Sambungan Las: Metode Pengelasan
Electroslag-WeldingProcess
-
Fahmi Mubarok
IV 16Mech. Eng. Dept. ITS Surabaya
Soldering and Brazing
Soldering and brazing are common methods of joining two
metals.
Soldering and brazing are not
In brazing, the filler material (silver, brass, bronze) has a
melting point above 425 C; and,In soldering, the filler material
(lead, tin) has a melting point well below 425 C.Capillary forces
for the wetting and flow of the liquid metal into the gaps.Proper
fluxes for lowering surface tension, remove oxides, and prevent
oxidation.
welding processes because they do not melt the parent
material.
In soldering and brazing, the parent metal is heated and the the
filler metal is melted into the joint where it cools.
Lead based filler metals are used in soldering and brass based
filler metals are used in brazing.
-
Fahmi Mubarok
IV 17Mech. Eng. Dept. ITS Surabaya
Filler Metals
Filler metal rods and wires are designated by a system
established by the American
Welding Society (AWS).
The static strength of a good weld isoften higher than the base
material.
-
Fahmi Mubarok
IV 18Mech. Eng. Dept. ITS Surabaya
Identifikasi Elektrode Pengelasan
Identifikasi tatanama elektrode telah dilakukan oleh AWS
(American Welding Sosiety), misalnya:
1/8" E6011dimana 1/8" = diameter elektrode (variasinya antara
1/16" sd 5/16".
E = simbol standar untuk elektrode.60 = kekuatan tarik (tensile
strength) , 60.000 psi = 60 ksi.
1 = posisi elektrode. EXX1X: semua posisi
EXX2X: posisi flat dan horisontal
EXX3X: posisi flat
1 = tipe pelapisan eletrode dan arus dalam pengelasan. EXX10:
DC+ (DC reverse or DCRP) electrode positive. EXX11: AC or DC- (DC
straight or DCSP) electrode negative. EXX12: AC or DC+ EXX13: AC,
DC- or DC+
-
Fahmi Mubarok
IV 19Mech. Eng. Dept. ITS Surabaya
Residual Stresses
The uneven heating and cooling in welding operations gives rise
to significant residual stresses in the vicinity of the weld.The
residual stresses may distort the part.The residual stresses and
discontinuities in a weld have a significant influence on the
fatigue life of a part.The fatigue life of a weld is often less
than the base material.Residual stresses are influenced by the %
carbon found in the material being joined.Residual stresses may be
removed by annealing.
-
Fahmi Mubarok
IV 20Mech. Eng. Dept. ITS Surabaya
AWS
-
Fahmi Mubarok
IV 21Mech. Eng. Dept. ITS Surabaya
AWS (contd)
-
Fahmi Mubarok
IV 22Mech. Eng. Dept. ITS Surabaya
Typical Welding Symbol
-
Fahmi Mubarok
IV 23Mech. Eng. Dept. ITS Surabaya
Typical Welding Symbol (contd)
-
Fahmi Mubarok
IV 24Mech. Eng. Dept. ITS Surabaya
Sambungan Las: Model Sambungan
-
Fahmi Mubarok
IV 25Mech. Eng. Dept. ITS Surabaya
Klasifikasi Mode Pembebanan
Welding
SymmetricallyLoaded
EccentricallyLoaded
In Tension In Shear On Plane Out of Plane
-
Fahmi Mubarok
IV 26Mech. Eng. Dept. ITS Surabaya
Butt Welds
-
Fahmi Mubarok
IV 27Mech. Eng. Dept. ITS Surabaya
Welds Loaded in Shear
-
Fahmi Mubarok
IV 28Mech. Eng. Dept. ITS Surabaya
Welds Loaded in Shear (contd)
-
Fahmi Mubarok
IV 29Mech. Eng. Dept. ITS Surabaya
ExampleThe figure shows a horizontal steel bar, 3/8 in thick,
loaded in tension andwelded to a vertical support. Find the load F
that will cause a shear stress in the welds of 20 kpsi.
-
Fahmi Mubarok
IV 30Mech. Eng. Dept. ITS Surabaya
Answer
AF
=
LhA ..7071.0=
Diketahui:= 20 kpsitbar= 3/8hlasan=5/16Llasan = 2
)"22("1657071.0
000.20xxx
Fpsi =
2884.0000.20 inxinlbF =
F = 22.6 kip
-
ELEMEN MESIN(RI.1232)
Dosen:Fahmi Mubarok, ST., MSc.Metallurgy LaboratoryMechanical
EngineeringITS- Surabaya2008
LECTURE VILECTURE VI
Sambungan-Sambuangan Baut dan Mur
-Sambungan Pen- Sambungan Pasak
Selamat Idul Fitri!
Elemen Pengikat (Fasteners, Connectors, Joints):
IntroduksiSambungan Las: ApliklasiWeldingWeldingModern Welding
ProcessesArc WeldingMetode Pengelasan: Arc WeldingMetode
Pengelasan: Arc WeldingMetode Pengelasan: Arc WeldingMetode
Pengelasan: Arc WeldingMIG or GMAWTIG or GTAWSambungan Las: Metode
PengelasanSambungan Las: Metode PengelasanSoldering and
BrazingFiller MetalsIdentifikasi Elektrode PengelasanResidual
StressesAWSAWS (contd)Typical Welding SymbolTypical Welding Symbol
(contd)Sambungan Las: Model SambunganKlasifikasi Mode
PembebananButt WeldsWelds Loaded in ShearWelds Loaded in Shear
(contd)ExampleAnswer