45 Series E Frame Tech Info (520L0519 Rev FK October 2008)

Series 45Axial Piston Open Circuit Pumps

Technical Information

2 520L0519 • Rev FK • October 2008

Series 45 Axial Piston Open Circuit PumpsTechnical Information

© 2008 Sauer-Danfoss. All rights reserved.Sauer-Danfoss accepts no responsibility for possible errors in catalogs, brochures and other printed material. Sauer-Danfoss reserves the right to alter its products without prior notice. This also applies to products already ordered provided that such alterations aren’t in conflict with agreed specifications. All trademarks in this material are properties of their respective owners. Sauer-Danfoss and the Sauer-Danfoss logotype are trademarks of the Sauer-Danfoss Group.

Front cover illustrations: F101 178, F101 180, F101 337, F101 168, P101 992

Revisions

Table of RevisionsDate Page Changed Rev.

October 2008 62, 65 add SAE-C two bolt housing FK

September 2008 58-62 dimension changes for Frame J FJ

June 2008 78, 93, 94, 95 various minor edits, removed S5 shaft from Frame E FI

May 2008 32, 74, 75, 92 correction to schematics drawings FH

April 2008 76 correction to S2 spline width (inch measurement only) FG

April 2008 52, 53 correction to schematics drawings FG

April 2008 27, 50, 72, 89 add Load sensing - RP and BP must be 20 bar FF

April 2008 76 Correction to S2 shaft - Class 6 and 37.91 mm length FF

March 2008 4 Correction to TOC FE

February 2008 Various Add LS setting to specifications for each frame FD

December 2007 Various Relocate F and E sections, add displacement limiter info. FC

November 2007 50 Change load sensing setting - bar increments FB

September 2007 Various Add Frame F, remove Frame G, and many edits FA

November 2006 51, 52, 53 Revised schematics information E

August 2005 - Removed Frame H, added Frame J D

April 2003 Added Frame E C

May 2001 - Added Frame H and Frame G B

May 1999 - First printing A

HistoRy of Revisions

3520L0519 • Rev FK • October 2008

Series 45 Axial Piston Open Circuit PumpsTechnical InformationContents

GeneRaL infoRmation

fRames L anD K

Overview ........................................................................................................................................................... 6Design ................................................................................................................................................................ 6Typical applications ....................................................................................................................................... 6

High performance .................................................................................................................................... 6Latest technology ..................................................................................................................................... 6Reliability ..................................................................................................................................................... 6

The Series 45 product family ...................................................................................................................... 7Basic units .................................................................................................................................................... 7

Load sensing open circuit system ............................................................................................................ 8Pressure compensated controls ................................................................................................................ 9

Operation ..................................................................................................................................................... 9Pressure compensated system characteristics ............................................................................... 9Typical applications for pressure compensated systems ........................................................... 9

Remote pressure compensated controls .............................................................................................10Remote pressure compensated system characteristics ............................................................10Typical applications for remote pressure compensated systems .........................................10

Load sensing controls .................................................................................................................................11Operation ...................................................................................................................................................11Load sensing system characteristics ................................................................................................11Typical applications for load sensing systems..............................................................................11

Electrical on/off pressure compensated controls .............................................................................12Operating parameters ................................................................................................................................13

Fluids ...........................................................................................................................................................13Viscosity......................................................................................................................................................13Temperature .............................................................................................................................................13Inlet pressure ............................................................................................................................................13Case pressure ...........................................................................................................................................13Pressure ratings .......................................................................................................................................14Speed ratings ...........................................................................................................................................14Duty cycle and pump life .....................................................................................................................14Speed, flow, and inlet pressure ...........................................................................................................14

Design parameters.......................................................................................................................................15Installation .................................................................................................................................................15Filtration .....................................................................................................................................................15Reservoir ....................................................................................................................................................15Fluid velocity ............................................................................................................................................16Shaft loads .................................................................................................................................................16Bearing life.................................................................................................................................................16Mounting flange loads ..........................................................................................................................17Auxiliary mounting pads ......................................................................................................................18Input shaft torque ratings ....................................................................................................................18Understanding and minimizing system noise .............................................................................19

Sizing equations ...........................................................................................................................................20

Design ..............................................................................................................................................................21Specifications .................................................................................................................................................22Performance L25C ........................................................................................................................................23Performance L30D .......................................................................................................................................24Performance K38C .......................................................................................................................................25Performance K45D .......................................................................................................................................26Order code ......................................................................................................................................................27

4 520L0519 • Rev FK • October 2008


fRames L anD K(continued)

fRame J

Controls ............................................................................................................................................................29Pressure compensated control (PC) .................................................................................................29Remote PC control (RP) .........................................................................................................................29Load sensing control (LS) .....................................................................................................................30Load sensing control with internal bleed orifice (LB) ................................................................30Normally closed on/off electric PC control (ED) .........................................................................31Normally open on/off electric PC control (AA) ............................................................................31Electric proportional control (EJ) (Normally closed) .................................................................32

Input shafts .....................................................................................................................................................33Auxiliary mounting pads ...........................................................................................................................35

SAE-A auxiliary mounting pad ...........................................................................................................35SAE-B auxiliary mounting pad ...........................................................................................................35 SAE-A Auxilliary Pad ..............................................................................................................................36 Mounting pads at 90 degrees ...........................................................................................................36Running cover ..........................................................................................................................................36 Special SAE-A 11 tooth ........................................................................................................................36

Displacement limiter ...................................................................................................................................37Installation drawings ...................................................................................................................................38

Axial ported endcap ..............................................................................................................................38Radial ported endcap ............................................................................................................................40Electric on/off control............................................................................................................................42

Design ..............................................................................................................................................................43Specifications .................................................................................................................................................44Performance J45B ........................................................................................................................................45Performance J51B ........................................................................................................................................46Performance J60B ........................................................................................................................................47Performance J65C ........................................................................................................................................48Performance J75C ........................................................................................................................................49Order code ......................................................................................................................................................50Controls ............................................................................................................................................................52

Pressure compensated control (PC, BC) ..........................................................................................52Remote PC control (RP, BP) ..................................................................................................................52Load sensing control (LS, BS) ..............................................................................................................53Load sensing control with internal bleed orifice (LB, BB) .........................................................53Normally closed on/off electric PC control (AG) .........................................................................54Normally open on/off electric PC control (AF) ............................................................................54


SAE-A auxiliary mounting pad (non-integral) ..............................................................................58SAE-B auxiliary mounting pad ...........................................................................................................58

Displacement limiter ...................................................................................................................................59SAE-C auxiliary mounting pad ...........................................................................................................60Running cover ..........................................................................................................................................60

Installation drawings ...................................................................................................................................61Axial ported endcap ..............................................................................................................................61Radial ported endcap ............................................................................................................................64Electric on/off control/Radial endcap .............................................................................................66

5520L0519 • Rev FK • October 2008


fRame e

fRame f Design ..............................................................................................................................................................68Specifications .................................................................................................................................................69Performance F74B ........................................................................................................................................70Performance F90C ........................................................................................................................................71Order code ......................................................................................................................................................72Controls ............................................................................................................................................................74

Pressure compensated control (PC) .................................................................................................74Remote PC Control (RP) ........................................................................................................................74Load sensing control with internal bleed orifice (LB) ................................................................75Load sensing control (LS) .....................................................................................................................75


SAE-A auxiliary mounting pad ...........................................................................................................77SAE-B auxiliary mounting pad ...........................................................................................................77

Displacement limiter ...................................................................................................................................78SAE-C auxiliary mounting pad ...........................................................................................................78

Adjustable displacement limiter and running cover .......................................................................79Axial ported endcap ....................................................................................................................................80Radial ported endcap .................................................................................................................................82

Design ..............................................................................................................................................................84Specifications .................................................................................................................................................85Performance E100B .....................................................................................................................................86Performance E130B .....................................................................................................................................87Performance E147C .....................................................................................................................................88Order code ......................................................................................................................................................89Controls ............................................................................................................................................................91

Pressure compensated control (PC) .................................................................................................91Remote PC control (RP) .........................................................................................................................91Load sensing control (LS) .....................................................................................................................92Load sensing control with internal bleed orifice (LB) ................................................................92


SAE-A auxiliary mounting pad ...........................................................................................................95SAE-B auxiliary mounting pad ...........................................................................................................95SAE-C auxiliary mounting pad ...........................................................................................................96Running cover ..........................................................................................................................................96

Displacement limiters .................................................................................................................................97Installation drawings ...................................................................................................................................98

Axial ported endcap, clockwise rotation ........................................................................................98Axial ported endcap, counterclockwise rotation ..................................................................... 100Radial ported endcap, clockwise rotation ................................................................................... 102Radial ported endcap, counterclockwise rotation ................................................................... 104

6 520L0519 • Rev FK • October 2008

Series 45 Axial Piston Open Circuit PumpsTechnical InformationGeneral information

oveRview Series 45 is a complete family of variable displacement, axial piston pumps for open circuit applications. Each frame within the Series 45 family is uniquely designed to optimize performance, size, and cost, matching the work function requirements of the demanding mobile equipment marketplace.

High performance• Displacements from 25 cm³ - 147 cm³ [1.53 - 8.97 in3/rev]• Speeds up to 3600 rpm• Pressures up to 310 bar [4495 psi] continuous, and 400 bar [5800 psi] peak• Variety of control system options including load sensing and pressure compensated• Through-drive capability for multi-circuit systems• Range of mounting flanges, shafts, and porting options for ease of installation

Latest technology• Customer-driven using quality function deployment (QFD) and design for

manufacturability (DFM) techniques• Optimized valve plates for maximum efficiency and quiet operation• Computer-modeled castings to optimize inlet conditions for maximum pump speed• Compact package size minimizing installation space requirements• Heavy-duty tapered roller bearings for long life• Single piece rigid housing to reduce noise and leak paths• Integrated controls for high speed response and system stability

Reliability• Designed to rigorous standards• Proven in both laboratory and field• Manufactured to rigid quality standards• Long service life• Significantly fewer parts• No gasketed joints• Robust input shaft bearings to handle large external shaft loads• Integrated gauge ports for monitoring operating conditions

• Cranes• Telescopic handlers• Forklift trucks• Wheel loaders• Sweepers• Backhoe loaders• Forestry and agricultural machinery• Fan drives• Other uses

DesiGn

tyPiCaL aPPLiCations

7520L0519 • Rev FK • October 2008


General performance specifications for the series 45 pump family

Pump Displacementspeed Pressure theoretical flow

(at rated speed)mounting

Continuous max. min. Continuous maximum

Model cm3 in3 min-1 (rpm) min-1 (rpm) min-1 (rpm) bar psi bar psi US gal/min l/min Flange

frame L See page 21

L25C 25 1.53 3200 3600 500 260 3770 350 5075 21.0 80.0 SAE B - 2 bolt

L30D 30 1.83 3200 3600 500 210 3045 300 4350 25.4 96.0 SAE B - 2 bolt

frame K See page 21

K38C 38 2.32 2650 2800 500 260 3770 350 5075 26.6 100.7 SAE B - 2 bolt

K45D 45 2.75 2650 2800 500 210 3045 300 4350 31.5 119.3 SAE B - 2 bolt

See page 43

J45B 45 2.75 2800 3360 500 310 4495 400 5800 33.3 126.0SAE B 2-bolt

SAE C 2 and 4-bolt

J51B 51 3.11 2700 3240 500 310 4495 400 5800 36.4 137.7SAE B 2-bolt

SAE C 2 and 4-bolt

J60B 60 3.66 2600 3120 500 310 4495 400 5800 41.2 156.0SAE B 2-bolt

SAE C 2 and 4-bolt

J65C 65 3.97 2500 3000 500 260 3770 350 5075 42.9 162.6SAE B 2-bolt

SAE C 2 and 4-bolt

J75C 75 4.58 2400 2880 500 260 3770 350 5075 47.5 180.0SAE B 2-bolt

SAE C 2 and 4-bolt

frame f See page 68

F74B 74 4.52 2400 2800 500 310 4495 400 5800 46.9 177.6 SAE B 2-boltSAE C 4-bolt

F90C 90 5.49 2200 2600 500 260 3770 350 5075 52.3 198 SAE B 2-boltSAE C 4-bol

frame e See page 84

E100B 100 6.10 2450 2880 500 310 4495 400 5800 64.7 245.0 SAE C 4-bolt

E130B 130 7.93 2200 2600 500 310 4495 400 5800 75.5 286.0 SAE C 4-bolt

E147C 147 8.97 2100 2475 500 260 3770 350 5075 81.5 308.7 SAE C 4-bolt

tHe seRies 45 PRoDuCt famiLy

Basic unitsThe series 45 family of open circuit, variable piston pumps, offers a range of displacements from 25 to 147 cm³/rev [1.53 to 8.97 in3/rev]. With maximum speeds up to 3600 rpm and continuous operating pressures up to 310 bar [4495 psi], you can tailor product selection to the flow and pressure requirements of your individual application.

K/L Frame E FrameF FrameJ Frame

8 520L0519 • Rev FK • October 2008


LoaD sensinG oPen CiRCuit system

The pump receives fluid directly from the reservoir through the inlet line. A screen in the inlet line protects the pump from large contaminants. The pump outlet feeds a PVG-32 multi-section, load sensing, directional control valve. The PVG valve directs pump flow to the cylinder and gear motor. A heat exchanger cools the fluid returning from the valve. A filter cleans the fluid before it returns to the reservoir.

Flow in the circuit determines the speed of the actuators. The position of the PVG valve determines the flow demand. A hydraulic pressure signal (LS signal) communicates demand to the pump control. The pump control monitors the pressure differential between pump outlet and the LS signal, and regulates servo pressure to control the swashplate angle. Swashplate angle determines pump flow.

Actuator load determines system pressure. The pump control monitors system pressure and will decrease the swashplate angle to reduce flow if system pressure reaches the PC setting. A system relief valve in the PVG valve acts as a back-up to control system pressure.

Pictorial circuit diagram

System pressure

Servo pressure

Actuator pressure

Load sense pressure

Actuator return

Suction / case drain /system return

K/L Frame Series 45open circuit axialpiston pump withload sensing control

PVG 32mulit-sectionloadsensingcontrolvalve

P101 658E

Reservoir FilterHeat exchanger

Double-acting cylinder

Bi-directionalgear motor

9520L0519 • Rev FK • October 2008


PRessuRe ComPensateD ContRoLs

operationThe PC control maintains constant system pressure in the hydraulic circuit by varying the output flow of the pump. Used with a closed center control valve, the pump remains in high pressure standby mode at the PC setting with zero flow until the function is actuated. This condition is often called a dead head condition.

P101 965

Simple closed-center circuit

Once the closed center valve is opened, the PC control senses the immediate drop in system pressure and increases pump flow by increasing the swashplate

00

Q max

Pressure

Flow

P101 166E

PC s

ettin

g

Typical operating curve

angle. The pump continues to increase flow until system pressure reaches the PC setting. If system pressure exceeds the PC setting, the PC control reduces the swashplate angle to maintain system pressure by reducing flow. The PC control continues to monitor system pressure and changes swashplate angle to match the output flow with the work function pressure requirements.

If the demand for flow exceeds the capacity of the pump, the PC control directs the pump to maximum displacement. In this condition, actual system pressure depends on the actuator load.

Each section includes control schematic diagrams, setting ranges, and response / recovery times for each control available. Response is the time (in milliseconds) for the pump to reach zero displacement when commanded by the control. Recovery is the time (in milliseconds) for the pump to reach full displacement when commanded by the control. Actual times can vary depending on application conditions.

Pressure compensated system characteristics• Constant pressure and variable flow• High pressure standby mode when flow is not needed• System flow adjusts to meet system requirements• Single pump can provide flow to multiple work functions• Quick response to system flow and pressure requirements

typical applications for pressure compensated systems• Constant force cylinders (bailers, compactors, refuse trucks)• On/off fan drives

For additional system protection, install a relief valve in the pump outlet

line.

10 520L0519 • Rev FK • October 2008


Remote PRessuRe ComPensateD ContRoLs

The remote PC control is a two-stage control that allows multiple PC settings. Remote PC controls are commonly used in applications requiring low and high pressure PC operation.

P101 966

Closed center circuit with remote PC

The remote PC control uses a pilot line connected to an external hydraulic valve. The external valve changes pressure in the pilot line, causing the PC control to operate at a lower pressure. When the pilot line is vented to reservoir, the pump maintains a low standby pressure of 15 to 20 bar [215 to 300 psi]. When pilot flow is blocked, the pump maintains pressure at the PC setting. An on-off solenoid valve can be used in the pilot line to create a low-pressure standby mode. A proportional solenoid valve, coupled with a microprocessor control, can produce an infinite range of operating pressures.


Size the external valve and plumbing for a pilot flow of 3.8 l/min [1 US gal/min]. For additional system protection, install a relief valve in the pump outlet line.

Remote pressure compensated system characteristics• Constant pressure and variable flow• High or low pressure standby mode when flow is not needed• System flow adjusts to meet system requirements• Single pump can provide flow to multiple work functions• Quick response to system flow and pressure requirements

typical applications for remote pressure compensated systems• Modulating fan drives• Anti-stall control with engine speed feedback• Front wheel assist

00

Q max

Pressure

Flo

w

P101 969EPC

set

tin

g

Rem

ote

PC

set

tin

g


11520L0519 • Rev FK • October 2008


LoaD sensinG ContRoLs

operationThe LS control matches system requirements for both pressure and flow in the circuit regardless of the working pressure. Used with a closed center control valve, the pump remains in low-pressure standby mode with zero flow until the valve is opened. The LS setting determines standby pressure.

P101 967

Load sensing circuit

Most load sensing systems use parallel, closed center, control valves with special porting that allows the highest work function pressure (LS signal) to feed back to the LS control. margin pressure is the difference between system pressure and the LS signal pressure. The LS control monitors margin pressure to read system demand. A drop in margin pressure means the system needs more flow. A rise in margin pressure tells the LS control to decrease flow.

LS control with bleed orificeThe load sense signal line requires a bleed orifice to prevent high-pressure lockup of the pump control. Most load-sensing control valves include this orifice. An optional internal bleed orifice is available, if needed.

Integral PC functionThe LS control also performs as a PC control, decreasing pump flow when system pressure reaches the PC setting. The pressure compensating function has priority over the load sensing function.


Load sensing system characteristics• Variable pressure and flow• Low pressure standby mode when flow is not needed• System flow adjusted to meet system requirements• Single pump can supply flow and regulate pressure for multiple circuits• Quick response to system flow and pressure requirements

typical applications for load sensing systems• Priority steering• Load independent flow control for boom lift, tilt, and rotation

00

P101 968E

PC s

etti

ng

Flo

w

Pressure

Q max


For additional system protection, install a relief valve in the pump outlet

line.

12 520L0519 • Rev FK • October 2008


eLeCtRiCaL on/off PRessuRe ComPensateD ContRoLs

The electrical on/off pressure compensated control allows the pump to operate as a PC type control under normal operating conditions. A solenoid valve overrides the PC control allowing the pump to operate in a low-pressure standby mode. This function provides reduced horsepower and torque loss in certain situations. It may be particularly useful to reduce loads on a system during engine start.

When closed, the solenoid valve prevents flow across the LS spool gain orifice,

ED schematic (normally closed)

M2

L2

S L1

X

P106 044

B

Solenoid

LS adjustment

PC adjustment

LS spool

PC spool

P106 183E

System pressure

Pilot PressureServo pressure

Drain

(ED) Electric control cross-section

defeating the LS spool. The pump then functions as a PC control pump. When open, the solenoid valve allows flow across the LS spool gain orifice to reservoir. This flow generates a pressure differential across the LS spool that shifts the spool and de-strokes the pump. The pump then operates in a low-pressure standby condition. The solenoid valve is available in a normally closed or normally open configuration.

ED is the nomenclature for a normally closed on/off control for the L and K frame pumps. Other frame sizes and configurations have different order code designations.

13520L0519 • Rev FK • October 2008


oPeRatinG PaRameteRs

fluidsRatings and performance data for Series 45 products are based on operating with premium hydraulic fluids containing oxidation, rust, and foam inhibitors. These include premium turbine oils, API CD engine oils per SAE J183, M2C33F or G automatic transmission fluids (ATF), Dexron II (ATF) meeting Allison C-3 or Caterpillar T0-2 requirements, and certain specialty agricultural tractor fluids. For more information on hydraulic fluid selection, see Sauer-Danfoss publications 520L0463 Hydraulic Fluids and Lubricants, Technical Information, and 520L0465 Experience with Biodegradable Hydraulic Fluids, Technical Information.

viscosityMaintain fluid viscosity within the recommended range for maximum efficiency and bearing life. minimum viscosity should only occur during brief occasions of maximum ambient temperature and severe duty cycle operation. maximum viscosity should only occur at cold start: Limit speeds until the system warms up.

temperatureMaintain fluid temperature within the limits shown in the table. minimum temperature relates to the physical properties of the component materials. Cold oil will not affect the durability of the pump components. However,

Fluid viscosity limitsCondition mm2/s (cst) sus

ν min.continuous 9 58

intermittent 6.4 47

ν max.continuous 110 500

intermittent (cold start)

1000 4700

Temperature limitsminimum (intermittent, cold start)

- 40° C [- 40° F]

Continuous 82° C [180° F]

maximum 104° C [220° F]

it may affect the ability of the pump to provide flow and transmit power. maximum temperature is based on material properties. Don’t exceed it. Measure maximum temperature at the hottest point in the system. This is usually the case drain.

Ensure fluid temperature and viscosity limits are concurrently satisfied.

inlet pressureMaintain inlet pressure within the limits shown in the table. Low inlet pressure (vacuum) may limit maximum pump speed and cause cavitation. Refer to Inlet pressure vs. speed charts for each displacement.

Case pressureMaintain case pressure within the limits shown in the table. The housing must always be filled with hydraulic fluid.

Inlet pressure limitsminimum(continuous)

0.8 bar absolute [6.7 in. Hg vac.](at reduced maximum speed)

minimum(cold start)

0.5 bar absolute [15.1 in. Hg vac.]

Case pressure limitsmaximum(continuous)

0.5 bar [7 psi] above inlet

intermittent(cold start)

2 bar [29 psi] above inlet

C CautionOperating outside of inlet and case pressure limits will damage the pump. To minimize this risk, use full size inlet and case drain plumbing, and limit line lengths.

14 520L0519 • Rev FK • October 2008


Pressure ratingsThe specification tables in each section give maximum and continuous pressure ratings for each displacement. Not all displacements within a given frame operate under the same pressure limits. Definitions of the operating pressure limits appear below.

system pressure is the differential pressure between the outlet and inlet ports. It is the dominant operating variable affecting hydraulic unit life. High system pressure, which results from high load, reduces expected life. System pressure must remain at or below rated pressure during normal operation to achieve expected life.

Continuous working pressure is the average, regularly occurring operating pressure. Operating at or below this pressure should yield satisfactory product life. For all applications, the load should move below this pressure.

maximum (peak) working pressure is the highest intermittent pressure allowed. Maximum machine load should never exceed this pressure.

speed ratingsThe specification tables in each section give minimum, maximum, and rated speeds for each displacement. Not all displacements within a given frame operate under the same speed limits. Definitions of these speed limits appear below.

Rated speed is the maximum recommended operating speed at full displacement and 1 bar abs. [0 in Hg vac] inlet pressure. Operating at or below this speed should yield satisfactory product life.

maximum speed is the highest recommended operating speed at full power conditions. Operating at or beyond maximum speed requires positive inlet pressure and/or a reduction of pump outlet flow. Refer to Inlet pressure vs. speed charts for each displacement.

minimum speed is the lowest operating speed allowed. Operating below this speed will not yield satisfactory performance.

Duty cycle and pump lifeKnowing the operating conditions of your application is the best way to ensure proper pump selection. With accurate duty cycle information, your Sauer-Danfoss representative can assist in calculating expected pump life.

speed, flow, and inlet pressureInlet pressure vs. speed charts in each section show the relationship between speed, flow, and inlet pressure for each displacement. Use these charts to ensure your application operates within the prescribed range.

The charts define the area of inlet pressures and speeds allowed for a given displacement. Operating at lower displacements allows greater speed or lower inlet pressure.

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

2800 3000 3200 3400 3600 3800 4000

100% 90% 80%

Shaft Speed min (rpm)-1

Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P101 972E

0

3

6

9

8

6

4

2

Sample inlet pressure vs. speed chart

Operating limit at 100% displacementOperating limit at 90% displacement

Operating limit at 80% displacement

Rated speed

Max. speed

oPeRatinG PaRameteRs(continued)

15520L0519 • Rev FK • October 2008


DesiGn PaRameteRs installationSeries 45 pumps may be installed in any position. To optimize inlet conditions, we recommend installing the pump at an elevation below the minimum reservoir fluid level. Design inlet plumbing to maintain inlet pressure within prescribed limits (see Inlet pressure limits, page 13)

Fill the pump housing and inlet line with clean fluid during installation. Connect the case drain line to the uppermost drain port (L1 or L2) to keep the housing full during operation.

To allow unrestricted flow to the reservoir, use a dedicated drain line. Connect it below the minimum reservoir fluid level and as far away from the reservoir outlet as possible. Use plumbing adequate to maintain case pressure within prescribed limits (see Case pressure limits, page 13).

filtrationTo prevent damage to the pump, including premature wear, fluid entering the pump inlet must be free of contaminants. Series 45 pumps require system filtration capable of maintaining fluid cleanliness at ISO 4406-1999 class 22/18/13 or better.

Sauer-Danfoss does not recommend suction line filtration. Suction line filtration can cause high inlet vacuum, which limits pump operating speed. Instead we recommend a 125 µm (150 mesh) screen in the reservoir covering the pump inlet. This protects the pump from coarse particle ingestion.

Return line filtration is the preferred method for open circuit systems. Consider these factors when selecting a system filter:• Cleanliness specifications• Contaminant ingression rates• Flow capacity• Desired maintenance interval

Typically, a filter with a beta ratio of β10 = 10 is adequate. However, because each system is unique, only a thorough testing and evaluation program can fully validate the filtration system. For more information, see Sauer-Danfoss publication 520L0467 Design Guidelines for Hydraulic Fluid Cleanliness.

ReservoirThe reservoir provides clean fluid, dissipates heat, and removes entrained air from the hydraulic fluid. It allows for fluid volume changes associated with fluid expansion and cylinder differential volumes. Minimum reservoir capacity depends on the volume needed to perform these functions. Typically, a capacity of one to three times the pump flow (per minute) is satisfactory.

Locate the reservoir outlet (suction line) near the bottom, allowing clearance for settling foreign particles. Place the reservoir inlet (return lines) below the lowest expected fluid level, as far away from the outlet as possible.

16 520L0519 • Rev FK • October 2008


DesiGn PaRameteRs(continued)

fluid velocityChoose piping sizes and configurations sufficient to maintain optimum fluid velocity, and minimize pressure drops. This reduces noise, pressure drops, and overheating. It maximizes system life and performance.

SI units

Q = flow (l/min)A = area (mm²)

Velocity = 16.67•Q (m/sec) A

Recommended fluid velocitiessystem lines 6 to 9 m/sec [20 to 30 ft/sec]

suction line 1 to 2 m/sec [4 to 6 ft/sec]

Case drain 3 to 5 m/sec [10 to 15 ft/sec]

typical guidelines; obey all pressure ratings.

Velocity equations US units

Q = flow (US gal/min)A = area (in²)

Velocity = 0.321•Q (ft/sec) A

shaft loadsSeries 45 pumps have tapered roller bearings capable of accepting external radial and thrust loads. The external radial shaft load limits are a function of the load position, orientation, and the operating conditions of the pump.

The maximum allowable radial load (Re) is based on the maximum external moment (Me) and the distance (L) from the mounting flange to the load. Compute radial loads using the formula below. Tables in each section give maximum external moment (Me) and thrust load (Tin , Tout) limits for each pump frame size and displacement.

Me = Re•LL = Distance from mounting flange

to point of loadMe = Maximum external moment Re = Maximum radial side load

Bearing lifeAll shaft loads affect bearing life. In applications where external shaft loads can not be avoided, maximize bearing life by orientating the load between the 150° and 210° positions, as shown. We recommend tapered input shafts or clamp-type couplings for applications with radial shaft loads. Tables in each section give B10 bearing life for each pump frame size and displacement.

Shaft load orientation

P101 080E

TinTout

L

Re

Mounting flange

0̊ Re

180˚ Re

90˚ Re 270˚ Re

150˚ 210˚

Axis of swashplaterotation

Radial load formula

17520L0519 • Rev FK • October 2008



mounting flange loadsAdding auxiliary pumps and/or subjecting pumps to high shock loads may overload the pump mounting flange. Tables in each section give allowable continuous and shock load moments for each frame size. Applications with loads outside allowable limits require additional pump support.

• shock load moment (MS) is the result of an instantaneous jolt to the system.

• Continuous load moments (Mc) are generated by the typical vibratory movement of the application.

Estimating overhung load momentsUse the equations below to estimate the overhung load moments for multiple pump mounting. See installation drawings in each section to find the distance from the mounting flange to the center of gravity for each frame size. Refer to the technical specifications in each section to find pump weight.

Shock load formula

Continuous load formula

Ms = Gs•K•(W1•L1+W2•L2+...Wn•Ln)

Mc = Gc•K•(W1•L1+W2•L2+...Wn•Ln)

mounting flange

Center of Gravity (CG)pump 1

L1L2

Center of Gravity (CG)pump 2

P101 081E

Overhung load example

SI unitsMs = Shock load moment (N•m)Mc = Continuous (vibratory) load

moment (N•m)Gs = Acceleration due to external

shock (G’s)Gc = Acceleration due to continuous

vibration (G’s)K = Conversion factor = 0.00981Wn = Mass of nth pump (kg)Ln = Distance from mounting flange

to nth pump CG (mm)

US unitsMs = Shock load moment (lbf•in)Mc = Continuous (vibratory) load

moment (lbf•in)Gs = Acceleration due to external

shock (G’s)Gc = Acceleration due to continuous

vibration (G’s)K = Conversion factor = 1Wn = Weight of nth pump (lb)Ln = Distance from mounting flange

to nth pump CG (in)

18 520L0519 • Rev FK • October 2008



auxiliary mounting padsAuxiliary mounting pads are available for all radial ported Series 45 pumps. Since the auxiliary pad operates under case pressure, use an O-ring to seal the auxiliary pump mounting flange to the pad. Oil from the main pump case lubricates the drive coupling.

• All mounting pads meet SAE J744 Specifications.

• The combination of auxiliary shaft torque and main pump torque must not exceed the maximum pump input shaft rating. Tables in each section give input shaft torque ratings for each frame size.

• Applications subject to severe vibratory or shock loading may require additional support to prevent mounting flange damage. Tables in each section give allowable continuous and shock load moments for each frame size.

• The drawing and table below give mating pump dimensions for each size mount. Refer to installation drawings in each section for auxiliary mounting pad dimensions.

Dimensionssae a sae B sae C

P82.55[3.250]

101.60[4.000]

127.00[5.000]

B6.35[0.250]

9.65[0.380]

12.70[0.500]

C12.70[0.500]

15.20[0.600]

23.37[0.920]

D58.20[2.290]

53.10[2.090]

55.60[2.190]

e15.00[0.590]

17.50[0.690]

30.50[1.200]

f13.50[0.530]

14.20[0.560]

18.30[0.720]

+0 -0.05[+0 -0.002]

mm[in.]

Dmax.

Emax.

F min. spline engagementfor full torque rating

Mountingflange (ref )

Undercutspline

Sled-runnerspline

P Ø

R 0.8 [0.03] max.

Bmax.

Cmax.

Coupling

Recommendedcutter clearance2.3 [0.090]

P101 079E

Mating pump specifications

input shaft torque ratingsInput shaft tables in each section give maximum torque ratings for available input shafts. Ensure that your application respects these limits.

maximum torque ratings are based on shaft strength. Do not exceed them.

Coupling arrangements that are not oil-flooded provide a reduced torque rating. Contact your Sauer-Danfoss representative for proper torque ratings if your application involves non oil-flooded couplings.

Sauer-Danfoss recommends mating splines adhere to ANSI B92.1-Class 5. Sauer-Danfoss external splines are modified class 5 fillet root side fit. The external major diameter and circular tooth thickness dimensions are reduced to ensure a good clearance fit with the mating spline. Tables in each section give full spline dimensions and data.

19520L0519 • Rev FK • October 2008


understanding and minimizing system noiseTables in each section give sound levels for each frame size and displacement. Sound level data are collected at various operating speeds and pressures in a semi-anechoic chamber. Many factors contribute to the overall noise level of any application. Here is some information to help understand the nature of noise in fluid power systems, and some suggestions to help minimize it.

Noise is transmitted in fluid power systems in two ways: as fluid borne noise, and structure borne noise.

fluid-borne noise (pressure ripple or pulsation) is created as pumping elements discharge oil into the pump outlet. It is affected by the compressibility of the oil, and the pump’s ability to transition pumping elements from high to low pressure. Pulsations travel through the hydraulic lines at the speed of sound (about 1400 m/s [4600 ft/sec] in oil) until there is a change (such as an elbow) in the line. Thus, amplitude varies with overall line length and position.

structure-borne noise is transmitted wherever the pump casing connects to the rest of the system. The way system components respond to excitation depends on their size, form, material, and mounting.

System lines and pump mounting can amplify pump noise. Follow these suggestions to help minimize noise in your application:

• Use flexible hoses.• Limit system line length.• If possible, optimize system line position to minimize noise.• If you must use steel plumbing, clamp the lines.• If you add additional support, use rubber mounts.• Test for resonants in the operating range, if possible avoid them.


20 520L0519 • Rev FK • October 2008


sizinG equations

Based on si units

Output flow Q = (l/min)

Input torque M = (N•m)

Input power P = = (kW)

Based on us units

Output flow Q = (US gal/min)

Input torque M = (lbf•in)

Input power P = = (hp)

SI units [US units]

Vg = Displacement per revolution cm3/rev [in3/rev]pO = Outlet pressure bar [psi]pi = Inlet pressure bar [psi]∆p = pO - pi (system pressure) bar [psi]n = Speed min-1 (rpm)ηv = Volumetric efficiencyηm = Mechanical efficiencyηt = Overall efficiency (ηv • ηm)

Variables

Vg • n • ηv

1000

Vg • ∆p

20 • π • ηm

Q • ∆p600 • ηt

M • n • π30 000

Vg • n • ηv

231

Vg • ∆p

2 • π • ηm

Q • ∆p1714 • ηt

M • n • π198 000

Use these equations to help choose the right pump size and displacement for your application:

Flow

Torque

Power

21520L0519 • Rev FK • October 2008

Series 45 Axial Piston Open Circuit PumpsTechnical InformationFrames L and K

DesiGn Series 45 Frame L and K pumps have a single servo piston design with a cradle-type swashplate set in polymer-coated journal bearings. A bias spring and internal forces increase swashplate angle. The servo piston decreases swashplate angle. Nine reciprocating pistons displace fluid from the pump inlet to the pump outlet as the cylinder block rotates on the pump input shaft. The block spring holds the piston slippers to the swashplate via the slipper retainer. The cylinder block rides on a bi-metal valve plate optimized for high volumetric efficiency and low noise. Tapered roller bearings support the input shaft and a viton lip-seal protects against shaft leaks.

An adjustable one spool (PC only, not shown) or two spool (LS and remote PC) control senses system pressure and load pressure (LS controls). The control ports system pressure to the servo piston to control pump output flow.

Servo piston

Tapered rollerbearing

Shaft seal

LS adjustment screw

LS spool

PC adjustment screw

PC spool

Swashplate

Input shaft

Cylinder block

Piston Slipper

Valve plate

Bias spring

Block spring

Slipper retainer

LS control(attached to endcap)

Endcap(axial ported)

P101 659E

Tapered roller bearing

Frame K/L cross section

22 520L0519 • Rev FK • October 2008


sPeCifiCations Features and options model

feature unit L25C L30D K38C K45D

Maximum Displacement cm³ [in³] 25 [1.53] 30 [1.83] 38 [2.32] 45 [2.75]

Flow at rated speed (theoretical) l/min [US gal/min]

80 [21]

96[25.4]

100.7[26.6]

119.3[31.5]

Input torque at maximum displacement (theoretical)

N•m/bar[lbf•in/1000 psi]

0.398[243]

0.477[291]

0.605[369]

0.716[438]

Mass moment of inertia of internal rotating components

kg•m²[slug•ft²]

0.00169[0.00125]

0.00161[0.00119]

0.00184[0.00135]

0.00203[0.00150]

Weight Axial ports kg [lb] 19 [42]

Radial ports 24 [53]

Rotation Clockwise, Counterclockwise

Mounting SAE-B

Auxiliary mounting (See page 35) SAE-A, SAE-B, SAE-BB

System ports (type) SAE O-ring boss

System ports (location) Axial, Radial

Control types (See page 29) EP, ED, AA, PC, Remote PC, LS, LS with internal bleed

Shafts (See page 33) Splined 13 tooth, 15 tooth

Tapered Ø 25.4 mm [1 in], 1:8 taperØ 22.23 mm [0.875 in], 1:8 taper

Straight Ø 22.23 mm [0.875 in](short)

Ø 22.23 mm [0.875 in](long)

Displacement limiters (See page 37) Optional, adjustable

Ratings model

Rating units L25C L30D K38C K45D

Input speed¹ minimum min-1 (rpm) 500 500 500 500

continuous 3200 3200 2650 2650

maximum 3600 3600 2800 2800

Working pressure continuous bar [psi] 260 [3770] 210 [3045] 260 [3770] 210 [3045]

maximum 350 [5075] 300 [4350] 350 [5075] 300 [4350]

External shaft loads

External moment (Me) N•m [lbf•in] 61 [540] 61 [540] 76 [673] 76 [673]

Thrust in (Tin), out (Tout) N [lbf ] 1000 [225] 1000 [225] 1200 [270] 1200 [270]

Bearing life at 140 bar [2030 psi] B10 hours 49 100 24 600 35 300 19 600

at 210 bar [3045 psi] 14 100 7230 11 400 6200

at 260 bar [3770 psi] 6590 — 5870 —

Mounting flange load moments

Vibratory (continuous) N•m [lbf•in] 1005 [8895]

Shock (max) 3550 [31 420]

1. Input speeds are valid at 1 bar absolute [0 in Hg vac] inlet pressure. See Inlet pressure vs. speed charts.

Sound levels²dB(a) 210 bar [3045 psi] 260 bar [3770 psi]

Pump model 1800 min-1(rpm) Rated speed 1800 min-1(rpm) Rated speed

L25C 65 69 66 70

L30D 66 70 — —

K38C 65 70 66 71

K45D 66 71 — —

2. Sound data was collected in a semi-anechoic chamber. Values have been adjusted (-3 dB) to reflect anechoic levels.

For general operating parameters, including fluid viscosity, temperature, and

inlet and case pressures, see page 13. For system

design parameters, including installation,

filtration, reservoir, and line velocities, see page 15.

For more information on noise levels, see page 19.

For definitions of pressure and speed ratings,

see page 14. For more information on external shaft loads, see page 16; mounting flange loads,

see page 17.

23520L0519 • Rev FK • October 2008


PeRfoRmanCe L25C

Input power vs. speed

Flow vs. speed

Inlet pressure vs. speed

Flow and power data valid at 49°C [120°F] and viscosity

of 17.8 mm²/sec [88 SUS].

The chart on the right shows allowable inlet

pressure and speed at various displacements.

Greater speeds and lower inlet pressures are possible

at reduced displacement. Operating outside of

acceptable limits reduces pump life.

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P101 970E

0

20

40

60

80

100

0 500 1000 1500 2000 2500 3000 35000

4

8

12

16

20

24

Pow

er (k

W)

Speed min (rpm)-1

Pow

er (h

p)

P101 971E

0

10

20

30

40

50

0 500 1000 1500 2000 2500 3000 35000

10

20

30

40

50

60

260 bar [3770 psi]

210 bar [3045 psi]

140 bar [2030 psi]

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

2800 3000 3200 3400 3600 3800 4000

100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P101 972E

0

3

6

9

8

6

4

2

24 520L0519 • Rev FK • October 2008


PeRfoRmanCe L30D


Flow vs. speed








0

20

40

60

80

100

0 500 1000 1500 2000 2500 30000

4

8

12

16

20

24

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P101 973E

0

10

20

30

40

50

0 500 1000 1500 2000 2500 30000

10

20

30

40

50

60

Pow

er (k

W)

Speed min (rpm)-1Po

wer

(hp

)P101 974E

210 bar [3045 psi]

140 bar [2030 psi]

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

2800 3000 3200 3400 3600 3800 4000

100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P101 972E

0

3

6

9

8

6

4

2


25520L0519 • Rev FK • October 2008


PeRfoRmanCe K38C


Flow vs. speed








0

25

50

75

100

125

0 500 1000 1500 2000 25000

5

10

15

20

25

30

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P101 975E

0

10

20

30

40

50

60

0 500 1000 1500 2000 25000

10

20

30

40

50

60

70

80

Pow

er (k

W)

Speed min (rpm)-1

Pow

er (h

p)

P101 976E

260 bar [3770 psi]

140 bar [2030 psi]

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

2200 2400 2600 2800 3000

100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P101 977E

0

3

6

9

8

6

4

2


26 520L0519 • Rev FK • October 2008


PeRfoRmanCe K45D



Flow vs. speed








0

20

40

60

80

100

120

140

0 500 1000 1500 2000 25000

5

10

15

20

25

30

35

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P101 978E

0

10

20

30

40

50

60

0 500 1000 1500 2000 25000

10

20

30

40

50

60

70

80

Pow

er (k

W)

Speed min (rpm)-1Po

wer

(hp

)P101 979E

210 bar [3045 psi]

140 bar [2030 psi]

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

2200 2400 2600 2800 3000

100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P101 977E

0

3

6

9

8

6

4

2

27520L0519 • Rev FK • October 2008


oRDeR CoDe

R ProductKR K Frame, variable displacement open circuit pump

LR L Frame, variable displacement open circuit pump

s RotationL Left hand (counterclockwise)

R Right hand (clockwise)

P Displacement and pressure rating025C 025 cm³/rev [1.53 in³/rev], 260 bar [3770 psi] continuous working pressure

030D 030 cm³/rev [1.83 in³/rev], 210 bar [3045 psi] continuous working pressure

038C 038 cm³/rev [2.32 in³/rev], 260 bar [3770 psi] continuous working pressure

045D 045 cm³/rev [2.75 in³/rev], 210 bar [3045 psi] continuous working pressure

C Control typePC Pressure compensated control

RP Remote pressure compensated control

Ls Load sensing / pressure compensating control

LB Load sensing / pressure compensating control with internal bleed orifice

eD Normally closed on/off electric PC control

eP Normally closed electric proportional control (fan drive applications)

aa Normally open on/off electric PC control

D PC setting (2 digit code, 10 bar increments)example 10 = 100

10–26 100 to 260 bar [1450 to 3770 psi] (025C and 038C)

10–21 100 to 210 bar [1450 to 3045 psi] (030D and 045D)

e Load sensing setting (2 digit code, 1 bar increments)example 20 = 20 bar

12–40 12 to 40 bar [174 to 580 psi]

nn Not applicable (use with PC and RP controls)

RP Must be 20 bar

f Not usednn Not applicable

G Pilot orificen None (standard)

H Gain orifice

R s P C D e f G H 1 2 3 1 2 3 L m n

– –

J K

28 520L0519 • Rev FK • October 2008


oRDeR CoDe (continued)

3 Standard orifice

J1 Input shaftC2 13 tooth, 16/32 pitch (ANSI A92.1 1970 - Class 5)

C3 15 tooth, 16/32 pitch (ANSI A92.1 1970 - Class 5)

t1 Ø 25.4 mm [1 in], 1:8 taper

t2 Ø 22.23 mm [0.875 in], 1:8 taper

K1 Ø 22.23 mm [0.875 in] (short)

K2 Ø 22.23 mm [0.875 in] (long)

J2 Auxiliary mounting flangen None

R Running cover

a SAE-A, 9-tooth output spline

t SAE-A, 11-tooth output spline

G SAE-A, 11 tooth rotated 90 degrees

B SAE-B, 13-tooth output spline

v SAE-BB, 15-tooth output spline

J3 System port size and locationCode Location Port type Inlet size Outlet size

K Radial 4 bolt split flange 38.1 mm [1.5 in] 25.4 mm [1 in]

m Axial 4 bolt split flange 31.8 mm [1.25 in] 25.4 mm [1 in]

f Axial O-ring boss 1 7/8 in. 1 5/16 in.

G Radial O-ring boss 1 7/8 in. 1 5/16 in.

K1 Shaft seala Single lip seal, viton

K2 Mounting flange and housing port style6 SAE-B 2-bolt, SAE O-ring boss housing ports

K3 Not usedn Not applicable

L Displacement limiterKnB None

PLB Endcap machined and plugged

aaa Adjustable, factory set at max angle

m Special hardwarennn None

n Special featuresnnn None

R s P C D e f G H 1 2 3 1 2 3 L m n

– –

J K

29520L0519 • Rev FK • October 2008


ContRoLs

PC schematic

M2

L2

S L1 P101 980

B

LegendB = OutletS = InletL1, L2 = Case drainM2 = System pressure gauge port

Remote PC control (RP)

Pressure compensated control (PC)

PC control setting rangemodel bar psi

L25C 100–260 1450–3770

L30D 100–210 1450–3045

K38C 100–260 1450–3770

K45D 100–210 1450–3045

Response/recovery times*(ms) Response Recovery

L25C 30 90

L30D 30 100

K38C 30 105

K45D 30 110

* For definitions, see page 9

Specifications

Schematic diagram


L25C 100–260 1450–3770

L30D 100–210 1450–3045

K38C 100–260 1450–3770

K45D 100–210 1450–3045


L25C 30 90

L30D 30 100

K38C 30 105

K45D 30 110

* For definitions, see page 10.

Specifications

Schematic diagram

LegendB = OutletS = InletL1, L2 = Case drainM2 = System pressure gauge portX = Remote PC port

Remote PC schematicX

B

M2

L2

S L1 P101 981

LS settingmodel bar psi

all 20 290

30 520L0519 • Rev FK • October 2008


ContRoLs (continued)

Load sensing control (Ls)

PC setting rangemodel bar psi

L25C 100–260 1450–3770

L30D 100–210 1450–3045

K38C 100–260 1450–3770

K45D 100–210 1450–3045


L25C 30 70

L30D 30 70

K38C 30 80

K45D 30 80


Specifications

Schematic diagramLS setting rangemodel bar psi

all 12–40 174–580

X

B

M2

L2

X L1 P101 982

LS Schematic

LegendB = OutletS = InletL1, L2 = Case drainM2 = System pressure gauge portX = LS signal port


L25C 100–260 1450–3770

L30D 100–210 1450–3045

K38C 100–260 1450–3770

K45D 100–210 1450–3045


L25C 30 70

L30D 30 70

K38C 30 80

K45D 30 80


Specifications


all 12–40 174–580

S

L2

M2

L1

B

X

P101 983

LB Schematic

LegendB = OutletS = InletL1, L2 = Case drainM2 = System pressure gauge portX = LS signal port

Load sensing control with internal bleed orifice (LB)

31520L0519 • Rev FK • October 2008



normally closed on/off electric PC control (eD)

Specifications

Schematic diagram


ED schematic

M2

L2

S L1

X

P106 044

B


L25C 30 90

L30D 30 100

K38C 30 105

K45D 30 110



L25C, K38C

100-240 bar [1450-3480 psi]

L30D, K45D

100-210 bar [1450-3045 psi]

normally open on/off electric PC control (aa)

Specifications

Schematic diagram


AA schematic

M2

L2

S L1

X

P106 049

B

Evaluate the system to decide if normally open on/off (failsafe) control is necessary.


L25C 30 90

L30D 30 100

K38C 30 105

K45D 30 110



L25C, K38C, L30D, K45D

100-210 bar [1450-3045 psi]

LS setting rangemodel bar psi

all 12-40 174-580


all 12-40 174-580

32 520L0519 • Rev FK • October 2008



electric proportional control (eJ) (normally closed)

Specifications

Schematic diagram LegendB = OutletS = InletL1, L2 = Case drainM2 = System pressure gauge portX = Remote PC port

EJ schematic

M2

L2

S L1

X

P106 687E

B


L25C, K38C

100-260 bar 1450-3370

L30D, K45D

100-210 bar 1450-3045


all 12-40 174-580

33520L0519 • Rev FK • October 2008


inPut sHafts

Code Descriptionmaximum torque rating¹N•m [lbf•in] Drawing

C2 13 tooth spline16/32 pitch(ANSI A92.1 1970 - Class 5)

288 [2546]

8 ± 0.475[0.31 ±0.02]

33[1.3]

15.2 ±0.5[0.6 ±0.02]

Ø21.72 ± 0.09[0.855 ±0.004]

Ø18.82[0.74] MAX

13 TOOTH16/32 PITCH30° PRESSURE ANGLE20.638 [0.813] PITCH DIAFILLET ROOT SIDE FITCOMPATIBLE WITH ANSI B92.1-1970CLASS 5 ALSO MATES WITHFLAT ROOT SIDE FIT

COUPLING MUST NOTPROTRUDE BEYONDTHIS POINT

P101 993E


404 [3575]

8± 0.475[0.31 ±0.02]

38[1.5]

23.35 ± 0.5[0.92 ±0.02]

Ø25.27 ± 0.12[0.995 ±0.005]

Ø21.92MAX [0.863]


15 TOOTH16/32 PITCH30° PRESSURE ANGLE23.813 [0.938] PITCH DIAFILLET ROOT SIDE FIT

CLASS 5 ALSO MATES WITHFLAT ROOT SIDE FIT

P101 994E

t1 Ø 25.4 mm [1 in]1:8 taper (SAE J501)

362 [3200]6.299 +0.025

-0.000

[0.248 +0.001 -0.000 ]

WOODRUFF KE Y

[0.875 +0.000 -0.010 ]

Ø22.22 [0.87]

GA UGE

3/4-16UNF-2A THD

9.42 ± 0.3[0.37 ±0.01]

25. 4 [1 ]

8 ± 0.8[0.31 ±0.03]

69.89 REF [2.75]

34.92± 0.63 [1.375 ±0.025]

26.97 [1.06]

C OUPLING MUST NO T PR OT RUDE BEY OND THIS POINT

125 TAPER PER METER SAE J501

GA UGE

P101 996E

22.225 +0.254 -0.000

COMPATIBLE WITH 25.4 [1] NOMINAL SHAFT DIAMETER

1. See Input shaft torque ratings, page 18 for an explanation of maximum torque.

34 520L0519 • Rev FK • October 2008


inPut sHafts (continued)


t2 Ø 22.23 mm [0.875 in]1:8 taper (SAE J501)

305 [2700]

8 ± 0.3[0.31 ±0.03]

28.68± 0.63 [1.129 ±0.025]

3.18± 0.3[0.13 ±0.01]

59.69 REF [2.35]

23.01 [0.91]

Ø22.22 [0.875]

Ø19.05 [0.75]

5/8-18 UNF 2A THD


GA UGE

GA UGE

6.299 +0.025 -0.000

[0.248 +0.001 -0.000 ]

WOODRUFF KE Y

[0.875 +0.000 -0.010 ]

P101 995E

22.225 +0.254 -0.000

125 TAPER PER METER SAE J501 COMPATIBLE WITH

22.2 [0.874] NOMINAL SHAFT DIAMETER

K1 Ø 22.23 mm [0.875 in]33 mm [1.3 in]

305 [2700]

8± 0.8[0.31 ±0.03]

33 [1.3]

Ø22.2 ±0.025[0.874 ±0.001]


6.35 [0.25]x 12.7 [0.50] LONGSQUARE KEY

P101 997E

[0.98 +0-0.01 ]

24.89+0-0.25

K2 Ø 22.23 mm [0.875 in]63 mm [2.48 in] long

305 [2700]

8 ± 0.3[0.315 ±0.035]

63 [2.48]

6.35 [0.25] x 38.1 [1.5] L ONG SQU ARE KE Y

CO UPLING MUST NO T PR OT RUDE BEY OND THIS POINT P101 998E

Ø22.2 ±0.025 [0.874 ±0.001]

[0.98 +0 -0.01 ]

24.89 +0 -0.25


35520L0519 • Rev FK • October 2008


auxiLiaRy mountinG PaDs

See page 18 for mating pump pilot and spline dimensions.

Dimensionssae-a auxiliary mounting pad

SpecificationsCoupling 9-tooth 11-tooth

spline minimum engagement

12.6 mm [0.50 in] 13.5 mm [0.53 in]

maximum torque 107 N•m [950 lbf•in] 147 N•m [1300 lbf•in]

Dimensionssae-B auxiliary mounting pad



13.2 mm [0.52 in] 16.1 mm [0.63 in]


53.2 [2.09]

106.4 [4.19]

59.65 [2.35]

228.53 [8.997]

1.95 [0.08]

8.1 ± 0.7 [0.319 ±0.028]

Ø88.62 [3.49]

3/8-16UNC-2BTHD 17.8 [0.70] MI N THD DEPTH

C OUPLING-SAE A: SPLINE: 11 TO OT H 16/32 PIT CH 30° PRESSURE ANGLE 17.463 [0.6875] PIT CH DI A FILLET RO OT SIDE FIT PER SAE B92.1-1970, CLASS 6

MOUNTIN G FLANGE

R 0.51 MA X [0.020]

8 ± 0.8 [0.32 ±0.03]

PER SAE J744

O-RING SEAL REQUIRED REF 82.22 [3.237] I.D. X 2.62 [0.103] CROSS SECTION

MIN SHAF T CLEARANC E

C OUPLING-SAE A: SPLINE: 9 T OO TH 16/32 PIT CH 30 PRESSURE ANGL E °14.288 [0.5625] PIT CH DI A FILLET RO OT SIDE FIT PER ANSI B92.1-1970, CLASS 6

Ø82. 6 +0.08 -0

[3.252 +0.003 -0 ]

P101999E

P/N 5000373

73 [2.87]

146 [5.75]

55.27 [2.18]

8 ± 0. 8 [0.31 ±0.03]

224.15 [8.82]

1. 3 [0.05]

11 ± 0.13 [0.43±0.01]

Ø105.64 [4.159]

1/2-13UNC-2BTHD 19.7 [0.76] MI N THD DEPTH

MOUNTIN G FLANGE

C OUPLING-SAE B SPLINE: 13 TO OT H 16/32 PIT CH 30° PRESSURE ANGLE 20.638 [0.8125] PIT CH DI A FILLET RO OT SIDE FIT PER ANSI B92.1-1970 CLASS 6

R2 MA X [0.08]

C OUPLING-SAE B-B SPLINE: 15 TO OT H 16/32 PIT CH 30 PRESSURE ANGL E °23.813 [0.9375] PIT CH DI A FILLET RO OT SIDE FIT PER ANSI B92.1-1970 CLASS 6

MIN SHAF T CLEARANC E

O-RING SEAL REQUIRED REF 101.32 [3.989] I.D .X 1.78 [0.070] CROSS SECTIO N

PER SAE J744

Ø101.65 +0.08 -0

[4.002 +0.003 -0 ]

P104000E

P/N 726935


36 520L0519 • Rev FK • October 2008


mounting pads at 90 degrees

P106 076E

DimensionsRunning cover

P106 077E

212.7[8.37]

auxiLLiaRy mountinG PaDs (continued)

P106 644E

sae-a auxilliary Pad special sae-a 11 tooth

37520L0519 • Rev FK • October 2008


DisPLaCement LimiteR L and K Frame open circuit pumps are available with an optional adjustable displacement limiter. This adjustable stop limits the pump’s maximum displacement.

Displacement limiter cross-section

Setting rangeL25C 0 to 25 cm³ [0 to 1.53 in³]

L30D 0 to 30 cm³ [0 to 1.83 in³]

K38C 0 to 38 cm³ [0 to 2.32 in³]

K45D 0 to 45 cm³ [0 to 2.75 in³] P104 084

Displacement per turnL25C 1.20 cm³/rev [0.07 in³/rev]

L30D 1.43 cm³/rev [0.09 in³/rev]

K38C 1.81 cm³/rev [0.11 in³/rev]

K45D 2.15 cm³/rev [0.13 in³/rev]

38 520L0519 • Rev FK • October 2008


instaLLation DRawinGs

Third-angleprojectionmm [in]

axial ported endcap

Clockwise rotation

Counterclockwise rotation

P106170E

[0.04]R1 MAX

[1.46]37

[3.999 0.001]± 101.57Ø 0.025±

[0.37]9.4

[6.89]175.1

[6.8]172.6

[3.15]80

[6.6]167.7

[5.29]134.3

[6.11]155.2

[2.44]62

LS SIGNALPORT X

SAE J1926/17/16-20 CASE DRAIN

PORT L1

SAE J1926/17/8-14

[8.79]223.2

[4.16]105.8

[2.77]70.4

[7.16]181.9

[2.67]67.7

[2.67]67.7

[0.59]15

[7.18]182.4

SYSTEM PRESSUREGAGE PORT M2

SAE J1926/19/16-18orM14x1.5-6H

[1.3]33

[1.3]33

SYSTEMPORT S (INLET)

SAE J1926/11 7/8-12

SYSTEMPORT B (OUTLET)

SAE J1926/11 5/16-12

PCPRESSUREADJUSTMENT

LS STANDBYPRESSUREADJUSTMENT

[1.3]33

[1.3]33

SYSTEMPORT B (OUTLET)

SAE J1926/11 5/16-12


SAE J1926/11 7/8-12

SYSTEM PORTS S & B SPOTFACE DEPTH

M2

CASE DRAINPORT L2 SPOTFACE DEPTH


SERVO PRESSUREGAGE PORT

SAE J1926/13/4-16

SERVO PRESSUREGAGE PORT

SAE J1926/13/4-16

ISO 11926-1

ISO 11926-1

ISO 11926-1

ISO 11926-1 ISO 11926-1

ISO 11926-1

ISO 11926-1 ISO 11926-1

ISO 11926-1

58.72[2.312]

52.37[2.062]

Ø31.8[1.25]INLETSYSTEM PORT ‘S’276 BAR [4000] PSI]SPLIT FLANGE BOSSPER ISO 6162SAE J518CODE 61with 7/16 - 14 UNCX 17 [0.669] MIN THD

30.18[1.188]

33[1.30]

26.19[1.031]

33[1.30]

Ø25.4[1]OUTLETSYSTEM PORT ‘B’345 BAR [5000] PSI]SPLIT FLANGE BOSSPER ISO 6162SAE J518CODE 61with 3/8 - 16 UNCX 20 [0.787] MIN THD

Split flange axial ports - counterclockwise rotation

39520L0519 • Rev FK • October 2008


P104064E

[3.9]99

[0.26]6.7

[2.87]73

[5.75]146

[4.8]121.9

[5.2]132

APPROXIMATECENTER OFGRAVITY

[1.26]32

[3.15]80

[1.02]25.8

[3.83]97.4


CASE DRAINPORT L2

SAE J1926/17/8-14

[3.28]83.3

[8.74]222

CCWCW

[0.563] 14.3Ø

2X

ISO 11926-1

axial ported endcap (continued)instaLLation DRawinGs (continued)


Adjustable displacement limiter

Split flange axial endcap (counterclockwise rotation shown)

40 520L0519 • Rev FK • October 2008


instaLLation DRawinGs (continued)

Radial ported endcap


Clockwise rotation


P106 171E

R1 MAX[0.04]

62[2.44]

166[6.54]

37[1.46]

80[3.15]

Ø101.57 ± 0.025 [3.999 ± 0.001]

9.4[0.37]

94.5[3.72]

94.5[3.72]

95[3.74]

95[3.74]

67.7[2.67]

67.7[2.67]

90.5[3.56]

207.9[8.19]

15[0.59]

207[8.15]

94.5[3.72]

94.5[3.72]

95[3.74]

95[3.74]

SYSTEM PORT B (OUTLET)

SAE J1926/11 5/16 -12

CASE DRAINPORT L1

SAE J1926/17/8 -14


SAE J1926/19/16 -18

B

SYSTEM PORT S SPOTFACE DEPTH

SYSTEM PORT B SPOTFACE DEPTH



SYSTEM PORT S SPOTFACE DEPTH

SYSTEM PORT B SPOTFACE DEPTH

ISO 11926-1

ISO 11926-1

ISO 11926-1

41520L0519 • Rev FK • October 2008


P104 065E

99[3.9]

4.4[0.17]

Ø14.3[0.563]

73[2.87]

146[5.75]

121.9[4.8]

132[5.2]

80[3.15]

166[6.54]

32[1.26]

134.3[5.29]

20.7[0.81]

155.2[6.11]

112.8[4.44]

146[5.75]

83.3[3.28]

222[8.74]


PCPRESSUREADJUSTMENT


CASE DRAINPORT L2

SAE J1926/17/8 -14


SAE J1926/11 7/8 -12


CCWCW

2X

LS SIGNAL PORT X SPOTFACE DEPTH

ISO 11926-1

ISO 11926-1

69.92[2.753]

Ø38.1[1.5]INLETSYSTEM PORT ‘S’207 BAR [3000] PSI]SPLIT FLANGE BOSSPER ISO 6162SAE J518CODE 61with 1/2 - 13 UNCX 27 [1.063] MIN THD

Ø25.4[1]OUTLETSYSTEM PORT ‘B’345 BAR [5000] PSI]SPLIT FLANGE BOSSPER ISO 6162SAE J518CODE 61with 3/8 - 16 UNCX 20 [0.787] MIN THD

35.85[1.411] 166

[6.54]

52.37[2.062]

29.19[1.031]

166[6.54]


Radial ported endcap (continued)


Adjustable displacement limiter

Split flange radial endcap (counterclockwise rotation shown)

42 520L0519 • Rev FK • October 2008



electric on/off control


P106 190E

Deutsch type(2) pin connector

16.9[0.67]

163.2[6.42]

7.8[0.31]

115.8[4.56]

9.5[0.375]

16.9[0.67]

(2) pin connectorDeutsch type

9.5[0.375]

197.9[7.79]

7.8[0.31]

163.3[6.43]

144.5[5.69]

2.9[0.11]

Electric solenoid control assembly (right side)

Electric solenoid control assembly (left side)

43520L0519 • Rev FK • October 2008

Series 45 Axial Piston Open Circuit PumpsTechnical InformationFrame J

DesiGn Series 45 Frame J pumps have a single servo piston design with a cradle-type swashplate set in polymer-coated journal bearings. A bias spring and internal forces increase swashplate angle. The servo piston decreases swashplate angle. Nine reciprocating pistons displace fluid from the pump inlet to the pump outlet as the cylinder block rotates on the pump input shaft. The block spring holds the piston slippers to the swashplate via the slipper retainer. The cylinder block rides on a bi-metal valve plate optimized for high volumetric efficiency and low noise. Tapered roller bearings support the input shaft and a viton lip-seal protects against shaft leaks.

An adjustable one spool (PC only, not shown) or two spool (LS and PC) control senses system pressure and load pressure (LS controls). The control ports system pressure to the servo piston to control pump output flow.

Frame J cross section

LS adjustment

PC adjustment

LS spool

PC spool


Servo piston

Swashplate

Taperedrollerbearing

Shaft seal

Tapered rollerbearing

Input shaft

Cylinderblock

Valveplate

Cylinderblockspring

Piston

Slipper

Slipper retainer

Bias springLS control

P104 204E

44 520L0519 • Rev FK • October 2008



feature unit J45B J51B J60B J65C J75C

Maximum Displacement cm³ [in³] 45 [2.75] 51 [3.11] 60 [3.66] 65 [3.97] 75 [4.58]


126.0[33.3]

137.7[36.4]

156.0[41.2]

162.6[42.9]

180.0[47.5]



0.716[436.9]

0.811[495.1]

0.956[583.6]

1.035[631.4]

1.193[728.1]



0.00455[0.00336]

0.00455[0.00336]

0.00455[0.00336]

0.00433[0.00319]

0.00433[0.00319]

Weight Axial ports kg [lb] 23.13 [51]

Radial ports 26.65 [58.8]


Mounting 2 bolt SAE-B and SAE-C, 4 bolt SAE-C

Auxiliary mounting (See page 58) SAE-A, SAE-B, SAE-BB, SAE-C

System ports (type) SAE O-ring boss. 4-bolt split flange


Control types (See page 52) AG, AF, PC, Remote PC, LS, LS with internal bleed

Shafts (See page 55) Splined 13 tooth, 14 tooth, 15 tooth

Tapered Ø 31.75 mm [1.25 in], 1:8 taper

Straight Ø 31.75 mm [1.25 in]

Displacement limiters Optional, adjustable

Ratings model

Rating units J45B J51B J60B J65C J75C

Input speed¹ minimum min-1 (rpm) 500 500 500 500 500

continuous 2800 2700 2600 2500 2400

maximum 3360 3240 3120 3000 2880

Working pressure

continuous bar [psi] 310 [4495] 310 [4495] 310 [4495] 260 [3770] 260 [3770]

maximum 400 [5800] 400 [5800] 400 [5800] 350 [5075] 350 [5075]


External moment (Me) N•m [lbf•in] 226 [2000] 226 [2000] 226 [2000] 226 [2000] 226 [2000]

Thrust in (Tin), out (Tout) N [lbf ] 2200 [495] 2200 [495] 2200 [495] 2200 [495] 2200 [495]

Bearing life at 140 bar [2030 psi] B10 hours 29 712 29 712 29 712 10 755 10 755

at 210 bar [3045 psi] 6834 6834 6834 2474 2474

at 260 bar [3770 psi] 3151 3151 3151 — —

at 310 bar [4495 psi] 1666 1666 1666 — —


Vibratory (continuous) N•m [lbf•in] SAE-C: 1500 [14 000], SAE-B: 735 [6500]

Shock (max) SAE-C: 5600 [50 000], SAE-B: 2600 [23 000]

1. Continuous input speeds are valid at 1 bar absolute [0 in Hg vac] inlet pressure. Maximum input speeds require changing the inlet pressure or reducing pump displacement. See Inlet pressure vs. speed charts.

Sound levels²dB(a) 210 bar [3045 psi] 260 bar [3770 psi] 310 bar [4495 psi]

model 1800 min-1 (rpm) Rated speed 1800 min-1 (rpm) Rated speed 1800 min-1 (rpm) Rated speed

J45B 75 79 77 80 76 80

J51B 75 79 77 78 77 78

J60B 75 79 77 79 76 79

J65C 75 78 77 77 — —

J75C 77 78 77 77 — —









see page 17.

45520L0519 • Rev FK • October 2008


PeRfoRmanCe J45B


Flow vs. speed









0

20

40

60

80

100

0 500 1000 1500 2000 2500 3000 35000

20

40

60

80

100

120

Pow

er (k

W)

Speed min (rpm)-1

Pow

er (h

p)

P104 205E

140 bar [2030 psi]

260 bar [3770 psi]

310 bar [4495 psi]

0

25

50

75

100

125

150

0 500 1000 1500 2000 2500 3000 35000

5

10

15

20

25

30

35

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P104 206E

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P104 207E

0

3

6

9

8

6

4

2

2400 2600 2800 3000 3200 3400 3600

46 520L0519 • Rev FK • October 2008



Flow vs. speed









0

25

50

75

100

125

150

175

0 500 1000 1500 2000 2500 3000 35000

10

20

30

40

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P104 209E

0

20

40

60

80

100

0 500 1000 1500 2000 2500 3000 35000

25

50

75

100

125

140 bar [2030 psi]

260 bar [3077 psi]310 bar [4

495 psi]

Pow

er (k

W)

Speed min (rpm)-1

Pow

er (h

p)

P104 208E

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P104 210E

0

3

6

9

8

6

4

2

2200 2400 2600 2800 3000 3200 3400 3600

PeRfoRmanCe J51B

47520L0519 • Rev FK • October 2008



Flow vs. speed









0

20

40

60

80

100

120

0 500 1000 1500 2000 2500 3000 35000

20

40

60

80

100

120

140

160

140 bar [2030 psi]

260 bar [3077 psi]310 bar [4495 psi]

Pow

er (k

W)

Speed min (rpm)-1

Pow

er (h

p)

P104 211E

0

25

50

75

100

125

150

175

200

0 500 1000 1500 2000 2500 3000 35000

10

20

30

40

50

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P104 212E

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P104 213E

0

3

6

9

8

6

4

2

2200 2400 2600 2800 3000 3200 3400

PeRfoRmanCe J60B

48 520L0519 • Rev FK • October 2008




Flow vs. speed








0

20

40

60

80

100

0 500 1000 1500 2000 2500 3000

0

20

40

60

80

100

120

140 bar [2030 psi]

210 bar [3045 psi]260 bar [3770 psi]

Pow

er (k

W)

Speed min (rpm)-1

Pow

er (h

p)

P104 214E

0

25

50

75

100

125

150

175

0 500 1000 1500 2000 2500 30000

5

10

15

20

25

30

35

40

45

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P104 215E

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P104 216E

0

3

6

9

8

6

4

2

2200 2400 2600 2800 3000 3200

PeRfoRmanCe J65C

49520L0519 • Rev FK • October 2008



Flow vs. speed









0

40

80

120

160

200

0 500 1000 1500 2000 25000

10

20

30

40

50

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P104 218E

0

20

40

60

80

100

0 500 1000 1500 2000 25000

20

40

60

80

100

120

Pow

er (k

W)

Speed min (rpm)-1

Pow

er (h

p)

P104 217E

260 bar [3770 psi]

210 bar [3045 psi]

140 bar [2030 psi]

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P104 219E

0

3

6

9

8

6

4

2

2000 2200 2400 2600 2800 3000 3200

PeRfoRmanCe J75C

50 520L0519 • Rev FK • October 2008


oRDeR CoDe

R ProductJR J Frame, variable displacement open circuit pump



P Displacement and pressure rating045B 045 cm³/rev [2.75 in³/rev], 310 bar [4495 psi] continuous working pressure

051B 051 cm³/rev [3.11 in³/rev], 310 bar [4495 psi] continuous working pressure




C Control typePC Pressure compensated control 100-280 bar [1450-4060 psi]

BC* Pressure compensated control 290-310 bar [4205-4495 psi]

RP Remote pressure compensated control 100-280 bar [1450-4060 psi]

BP* Remote pressure compensated control 290-310 bar [4205-4495 psi]

Ls Load sensing / pressure compensating control 100-280 bar [1450-4060 psi]

Bs* Load sensing / pressure compensating control 290-310 bar [4205-4495 psi]

LB Load sensing / pressure compensating control with internal bleed orifice 100-280 bar [1450-4060 psi]

BB* Load sensing / pressure compensating control with internal bleed orifice 290-310 bar [4205-4495 psi]

aG Pressure compensated control with electric on/off solenoid operated 2-way valve (normally closed)

af Pressure compensated control with electric on/off solenoid operated 2-way valve (normally open)

* Use only with 45, 51, and 60 cm³ displacements.

D PC setting (2 digit code, 10 bar increments)example 10 = 100 bar

10–26 100 to 260 bar [1450 to 3770 psi] (065C and 075C)

10–31 100 to 310 bar [1450 to 4495 psi] (045B, 051B and 060B)


10–40 10 to 40 bar [145 to 580 psi]

nn Not applicable (use with PC controls)

RP and BP Must be 20 bar



H Gain orifice3 Standard orifice

R s P C D e f G H 1 2 3 1 2 3 L m n

– –

J K

51520L0519 • Rev FK • October 2008



J1 Input shaftC2 13 tooth, 16/32 pitch (ANSI A92.1 1970 - Class 5)

C3 15 tooth, 16/32 pitch (ANSI A92.1 1970 - Class 5)

s1 14 tooth, 12/24 pitch (ANSI A92.1 1970 - Class 5)

K4 Ø 31.75 mm [1.25 in] straight key

to Ø 31.75 mm [1.25 in], 1:8 taper

J2 Auxiliary mounting flange type and couplingn None (Use with axial ported endcap options 3 and 4 below)

a SAE-A, 9-tooth output spline

B SAE-B, 13-tooth output spline

C SAE-C, 14-tooth output spline

t SAE-A, 11-tooth output spline

v SAE-BB, 15-tooth output spline

R Running cover (Radial ported endcap machined for aux. pad. Pad and coupling sold separately.)

G Special SAE-A, 11 tooth, rotated 90 degrees

J3 Endcap option (system port size and location)Code Port location Port type Inlet size Outlet size

2 Radial 4-bolt split flange 50.8 mm [2.0 in] 25.4 mm [1.0 in]

3 Axial O-ring boss 1 7/8 in. 1 5/16 in.

4 Axial 4-bolt split flange 50.8 mm [2.0 in] 25.4 mm [1.0 in]

v * Radial 4-bolt split flange 50.8 mm [2.0 in] 25.4 mm [1.0 in]

w ** Axial 4-bolt split flange 50.8 mm [2.0 in] 25.4 mm [1.0 in]

* must have auxilliary mounting flange or runnung cover

** must have displacement limiter FFF


K2 Mounting flange and housing port style2 SAE-C 4-bolt, SAE O-ring boss housing ports

8 SAE-B 2-bolt, SAE O-ring boss housing ports

9 SAE-C 2-bolt, SAE O-ring boss housing ports


L Displacement limiternnn None

fff * Adjustable, factory set at maximum angle

* can only be used with v and w endcap options



R s P C D e f G H 1 2 3 1 2 3 L m n

– –

J K

52 520L0519 • Rev FK • October 2008


ContRoLs

Remote PC control (RP, BP)

Pressure compensated control (PC, BC)

Specifications

Schematic diagram

Specifications

Schematic diagram

LegendB = OutletS = InletL1, L2 = Case drainM1* = System pressure gauge port* M1 port is available on axially ported endcaps

only

LegendB = OutletS = InletL1, L2 = Case drainX = Remote PC portM1* = System pressure gauge port* M1 port is available on axially ported endcaps

only

Attach remote PC valve at port X. Size the external valve and plumbing for a pilot flow of 3.8 l/min [1 US gal/min].

Remote PC schematic

M1

L2

S L1 P104 221

X

X

B

PC schematic

B

M1

L2

S L1 P104 220

PC control setting rangemodel RP BP

J45B, J51B, J60B

100-280 bar[1450-4060 psi]

290-310 bar[4205-4495 psi]

J65C, J75C

100-260 bar[1450-3770 bar]

N/A


J45B 33 140

J51B 33 150

J60B 39 170

J65B 45 140

J75B 45 150

* For definitions, see page 10


J45B 33 140

J51B 33 150

J60B 39 170

J65B 45 140

J75B 45 150


PC control setting rangemodel PC BC

J45B, J51B, J60B

100-280 bar[1450-4060 psi]

290-310 bar[4205-4495 psi]

J65C, J75C

100-260 bar[1450-3770 bar]

N/A


all 20 290

53520L0519 • Rev FK • October 2008



Load sensing control (Ls, Bs)

Specifications

Schematic diagram LS setting rangemodel bar psi

all 10-40 145–580

Specifications


all 10–40 145–580

Load sensing control with internal bleed orifice (LB, BB)

LegendB = OutletS = InletL1, L2 = Case drainX = LS signal portM1* = System pressure gauge port* M1 port is available on axially ported endcaps

only

LegendB = OutletS = InletL1, L2 = Case drainX = LS signal portM1* = System pressure gauge port* M1 port is available on axially ported endcaps

only

LS Schematic

M1

L2

S L1

X

X

P104 223

B

LSBSchematic

M1

L2

S L1

X

X

P104 222

B

Response/recovery times*(ms) J45B J51B J60B J65B J75B

Response 28 30 33 43 45

Recovery 111 125 140 101 140


PC control setting rangeCode Ls Bs

J45B, J51B, J60B

100-280 bar[1450-4060 psi]

290-310 bar[4205-4495 psi]

J65C, J75C

100-260 bar[1450-3770 bar]

N/A

PC control setting rangeCode LB BB

J45B, J51B, J60B

100-280 bar[1450-4060 psi]

290-310 bar[4205-4495 psi]

J65C, J75C

100-260 bar[1450-3770 bar]

N/A


Response 28 30 33 43 45

Recovery 111 125 140 101 140


54 520L0519 • Rev FK • October 2008



normally closed on/off electric PC control (aG)

Specifications

Schematic diagram


only

AG schematic

M1

L2

S L1

X

P106 656E

B


Response 33 33 39 45 45

Recovery 140 150 170 140 150


PC control setting rangeCode aG

J45B, J51B, J60B

100-280 bar[1450-4060 psi]

J65C, J75C

100-260 bar[1450-3770 bar]

normally open on/off electric PC control (af)

Specifications

Schematic diagram


only

AF schematic

M1

L2

S L1

X

P106 657E

B


Response 33 33 39 45 45

Recovery 140 150 170 140 150


AF control setting rangeCode af

J45B, J51B, J60B

100-280 bar[1450-4060 psi]

J65C, J75C

100-260 bar[1450-3770 bar]

Evaluate your system to decide if normally open or normally closed control override is required for failsafe operation.


all 10-40 145-580


all 10-40 145-580

55520L0519 • Rev FK • October 2008


inPut sHafts



For use with SAE-B

288 [2546]

Ø18.63 MAX

8± 0.8[0.31 ±0.03]

33[1.3]

15.2 ± 0.5[0.6 ±0.02]

Ø21.72 ± 0.09[0.855 ±0.004]



[0.733]

P104 224E


For use with SAE-B

404 [3575]

25.27 ± 0.13[0.995 ±0.005]

Ø21.96 MAX

8± 0.8[0.31 ±0.03]

38[1.5]

22.36 ± 0.5[0.88 ±0.02]



[0.864]

P104 225E


56 520L0519 • Rev FK • October 2008




s1 14 tooth spline12/24 pitch (ANSI A92.1 1970 - Class 5)

For use with SAE-C

734 [6495]

8± 0.8[0.31 ±0.03]

Ø25.5 MAX[1]

Ø31.14 ± 0.08[1.226 ±0.003]

28 ± 0.5[1.1 ±0.02]

47.6[1.87]

COUPLING MUST NOTPROTRUDE BETONDTHIS POINT

14 TOOTH 12/24 PITCH30° PRESSURE ANGLE29.634 [1.167] PITCHFILLET ROOT SIDE FITCOMPATIBLE WITHANSI B92.1-1970 CLASS 5ALSO MATES WITHFLAT ROOT SIDE FIT

P104 226E

K4 Ø 31.75 mm [1.25 in]straight key

For use with SAE-C

655 [5797] 56[2.2]

48.03±0.43

[1.89]±0.02

8± 0.8[0.31 ±0.03]

35.2 ± 0.13[1.39 ±0.01]

Ø31.72 ± 0.025[1.249 ±0.001]

7.94 [0.313]X 28.56 [1.125] LONGSQUARE KEY

COUPLING MUST NOTPROTRUDE BETONDTHIS POINT

P104 227E


57520L0519 • Rev FK • October 2008



to Ø 31.75 mm [1.25 in]1:8 taper

For use with SAE-C

734 [6495]

8± 0. 8 [0.31 ±0.03]

22. 4 ± 0. 3 [0.88 ±0.01]

Ø30.1625 [1.19]

42.92

[1.69]

30.96±0.25

[1.219]±0.01

GA UGE GA UGE

7.887

X Dia. 31.8

WOODRUFF KEY

1.00-20 UNF-2A THD


P104 228E

125 TAPER PER METER SAE J501 COMPATIBLE WITH

31.8 [1.25] NOMINAL SHAFT DIAMETER

+0.8-1.1

+.03-0.04

[0.3105]

+0.025- 0

+0.001- 0

[1.25]

+0- 0.010+0-0.25



58 520L0519 • Rev FK • October 2008


auxiLiaRy mountinG PaDs


Dimensionssae-a auxiliary mounting pad (non-integral)




13.5 mm [0.53 in] 15 mm [0.59 in]


3[0.12]

9.8[0.39]

53. 2 [2.09]

106. 4 [4.19]

3/8 -16 UNC-2B THD

137.1[5.4]

264.43[10.41]

59.4[2.34]

8.1[0.32]

1.95[0.08]

23 [0.91]

Ø82. 6 +0.08 -0

[3.25 ] Ø88.62 [3.49]

R1.2 MA X

17.8 [0.70] MI N FULL THD DEPTH 2X

APPR OX IM AT E CENTER OF GR AV IT Y APPR OX IM AT E

CENTER OF GR AV IT Y

MOUNTING FLANGE

O-RING SEAL REQUIRED REF 82.22 [3.23] I.D x2.62 [0.103] CROSS SECTIONP/N 5000373

P104 230E

C OUPLING-SAE A T SPLINE: 11 TO OT H 16/32 PI TC H 30° PRESSURE ANGLE 17.463 [0.6875] PIT CH DI A FILLET RO OT SIDE FI T PER ANSI B92.1-1970 CLASS 6

C OUPLING-SAE A A SPLINE: 9 T OO TH 16/32 PI TC H 30° PRESSURE ANGLE 14.288 [0.5625] PIT CH DI A FILLET RO OT SIDE FI T PER ANSI B92.1-1970 CLASS 6

+0.003 -0


73 [2.87]

146 [5.75]

3.1[0.122]

9.8[0.39]

260.05 [10.24]

22 [0.87]

R2.0 MA X [0.08]

Ø101.65 +0.08 - 0

[4.002 ] +.003 - 0

Ø105.64 [4.159]

1.3 [0.05]

11 ± 0.12 [0.433 ±0.005]

55[2.17]

136.1[5.4]

APPRO XIM AT E CENTER OF GRA VIT Y

MIN SHAFT CLEARANCE

C OUPLING-SAE B-B V SPLINE: 15 TO OT H 16/32 PIT CH 30° PRESSURE ANGL E 23.813 [0.9375] PIT CH DI A FILLET RO OT SIDE FIT PER ANSI B92.1-1970 CLASS 6


1/2 -13UNC-2B TH D 19.7 [0.76] MI N THD DEPTH 2X

O-RING SEAL REQUIRED REF 101.32 [3.989] I.D . X 1.78 [0.070] CROSS SECTIONP/N 726935

C OUPLING-SAE B B SPLINE: 13 TO OT H 16/32 PIT CH 30° PRESSURE ANGL E 20.638 [0.8125] PIT CH DI A FILLET RO OT SIDE FIT PER ANSI B92.1-1970 CLASS 6

MOUNTIN G FLANGE

P104 231E



14.2 mm [0.56 in] 18.9 mm [0.74 in]


59520L0519 • Rev FK • October 2008


DisPLaCement LimiteR J Frame open circuit pumps are available with an optional adjustable displacement limiter. This adjustable stop limits the pump’s maximum displacement.


Setting rangeJ45B 8.4 to 45 cm³ [0.51 to 2.75 in³]

J51B 13.7 to 51 cm³ [0.84 to 3.11 in³]

J60B 16.8 to 60 cm³ [1.03 to 3.66 in³]

J65B 25.4 to 65 cm³ [1.55 to 3.97 in³]

J75B 28.4 to 75 cm³ [1.73 to 4.58 in³]

P106 727E

Displacement per turnJ45B 6.2 cm³/rev [0.38 in³/rev]

J51B 6.2 cm³/rev [0.38 in³/rev]

J60B 6.2 cm³/rev [0.38 in³/rev]

J65B 7.2 cm³/rev [0.44 in³/rev]

J75B 7.2 cm³/rev [0.44 in³/rev]

Displacement limiters are only available for endcap options V and W.

60 520L0519 • Rev FK • October 2008



Dimensionssae-C auxiliary mounting pad

SpecificationsCoupling 14-tooth


18.3 mm [0.72 in]

maximum torque 339 N•m [3000 lbf•in]

auxiLiaRy mountinG PaDs (continued)

14 [0.55]

1. 3 [0.05]

11 [0.43]

Ø131.57 [5.18]

263.05 [10.36]

Ø127.03 +0.05 - 0

[5.001 ] +.002 - 0

58.0[2.28]

138.95[5.5]

57.3 [2.26]

114.6 [4.51]

57.3 [2.26]

114. 6 [4.51]

2.9[0.114]

9.7[0.38]

MIN SHAFT CLEARANCE

MOUNTIN G FLANGE


1/2 -13 UNC-2B TH D 22.7 [0.89] MI N THREAD DEPTH 4X


O-RING SEAL REQUIRED REF 126.72 [4.989] I.D. x 1.78 [0.070] CROSS SECTIONP/N 331256

C OUPLING-SAE C C SPLINE: 14 TO OT H 12/24 PIT CH 30° PRESSURE ANGL E 29.633 [1.1667] PIT CH DI A FILLET RO OT SIDE FIT PER ANSI B92.1-1970 CLASS 6

P104 232E

Running cover

Endcap and shaft machined to accommodate auxiliary

mounting pads; pad and coupling not included.

Conversion kits are available for installation in the field.

250.56[9.86]

MOUNTINGFLANGE

P104 233E

61520L0519 • Rev FK • October 2008



Clockwise rotation, O-ring boss ports

Counterclockwise rotation, O-ring boss ports

axial ported endcapinstaLLation DRawinGs

Ø101.58 ± 0.025[3.999 ±0.001]

R1 MA X [0.04]

9. 4 [0.37]

198. 8 [7.83]

15 [0.59]

82. 4 [3.24]

77. 5 [3.05]

113.6[4.5]

36. 2 [1.4 ]

44. 5 [1.75]

82.1[3.2]

262.3[10.33]

83.4[3.28]

47 [1.85]

28.9[1.14]

246.3[9.7]

73. 2 [2.88]

137. 1 [5.4 ]

37 [1.46]

APPR OX IM AT E CENTER OF GR AV IT Y

SY STEM PORT S

SY STEM PORT B

SY STEM PRESSURE

CASE DRAIN PORT L1

LS SIGNAL PORT X

CASE DRAIN PORT L2

CASE DRAI N PORT L1 SPO TF AC E DEPTH

CASE DRAI N PORT L2 SPO TF AC E DEPTH

(INLET POR T)

SAE J1926/1 1 7/8 -12

(OUTLET POR T)

SAE J1926/ 1 1 5/16 -12

BO TH SIDES

GA UGE PORT M1

SAE J1926/ 1 9/16 -18 SAE J1976/ 1

7/8 -14

SAE J1926/1 7/16 -20

BO TH SIDES

SAE J1926/ 1 7/8 -14

P106 172E

ISO 11926-1

ISO 11926-1

ISO 11926-1

ISO 11926-1 ISO 11926-1

ISO 11926-1 36. 2 [1.43]

44. 5 [1.8 ]

SY STEM PORTS

SY STEM PORT B

(INLET POR T)

SAE J1926/ 1 1 7/8 -12

(OUTLET POR T)

SAE J1926/1 1 5/16 -12

ISO 11926-1

ISO 11926-1

62 520L0519 • Rev FK • October 2008


73 [2.87]

146 [5.75]

Ø14. 4 [0.567]

77. 2 [3.04]

0. 9 [0.04]

11.2[0.4]

96.7[3.81]

53.3 [2.1 ]

92. 7 [3.65]

APPR OX IM AT E CENTER OF GR AV IT Y PC PRESSURE

LS ST ANDBY

ADJUSTMENT

PRESSURE ADJUSTMENT

LS SIGNAL PORT X AL TERNA TE

LS SIGNAL PORT X

2X

P104 234E

93 [3.66]

232. 3 [9.15]

Ø17.5[0.69]

90.5[3.56]

181[7.13]

2X

12.

Ø126.975 ± 0.025

57.25 [2.25]

114. [4.51]

2X

2X

Ø14.4 [0.567] X4

7 [0.5

[4.999 ±0.001]

5 ]

instaLLation DRawinGs(continued)


SAE-C four-bolt housing

PC only control

axial ported endcap (continued)

The drawings on these pages show a pump with

two-bolt SAE-B and SAE-C mounting flanges. This

pump is also available with a four-bolt SAE-C mounting

flange. The differences are detailed in the drawing

to the right. All other dimensions are common.

SAE-B two-bolt housing

SAE-C two-bolt housing

63520L0519 • Rev FK • October 2008


36.2[1.43]

44.5[1.75]

44.5[1.75]

36.2[1.43]

SYSTEM PORT SOUTLET Ø50.8 [2]

SYSTEM PORT B

(INLET PORT)

3000 PSISPLIT FLANGE BOSS

SAE J518(CODE 61)

(OUTLET PORT)


SAE J518(CODE 61)

P104 235E

207 bar

PER ISO 6162

with 1/2-13 UNCX 27 [1.063] MIN THREAD

OUTLETØ25.4 [1]

345 bar

PER ISO 6162

with 3/8-16 UNCX 18.61 [0.732] MIN THREAD

77.77[3.062]

42.88[1.688]

26.19[1.031]

52.37[2.062]

SYSTEM PORT SOUTLET Ø50.8 [2]

(INLET PORT)


SAE J518(CODE 61)

207 bar

PER ISO 6162

with 1/2-13 UNCX 23 [0.906] MIN THREAD

SYSTEM PORT B(OUTLET PORT)


SAE J518(CODE 61)

OUTLETØ25.4 [1]

345 bar

PER ISO 6162

with 3/8-16 UNCX 18.61 [0.732] MIN THREAD

77.77[3.062]52.37

[2.062]

42.88[1.688]

26.19[1.031]

Clockwise rotation, split-flange ports

Counter clockwise rotation, split-flange ports

instaLLationDRawinGs(continued)

axial ported endcap (continued)

64 520L0519 • Rev FK • October 2008



Clockwise rotation


Radial ported endcapinstaLLationDRawinGs

77.5[3.05]

194.6[7.66]

9.4[0.37]

242.4[9.54]

Ø101.58 ± 0.025[3.999 ±0.001]

R1 MAX[0.04]

15[0.59]

239.8[9.44]

200.4[7.89]

82.4[3.24]

SYSTEM PORT S

116.5[4.59]

44.9[1.77]

132[5.2]

76.2[3]

84[3.31]

99.4[3.9]

47[1.85]

82.1[3.23]

37[1.46]

137.1[5.4]76.2

[3]84

[3.31]

PC PRESSURE

LS STANDBY

LS SIGNAL PORT X

CASE DRAIN PORT L1

CASE DRAIN PORT L2

CASE DRAINPORT L2SPOTFACEDEPTH

LS SIGNAL PORT X

LS SIGNAL PORT XALTERNATE

CASE DRAINPORT L1SPOTFACEDEPTH

(INLET PORT)207 BAR [3000 PSI}SPLIT FLANGE

SAE J518(CODE 61)

ADJUSTMENT

PRESSUREADJUSTMENT

SAE J1926/10.4375-20

BOTHSIDES

SYSTEMPORT SINLET

SYSTEMPORT BOUTLET

BOTHSIDES

SAE J 1976/17/8-14

SAE J1926/17/8-14

SYSTEMPORT SINLET

SYSTEMPORT BOUTLET

P106 173E

PER ISO 11976-1

PER ISO 6162

with 1/2-13 UNCX 27 [1.063] MIN THREAD DEPTH

Ø50.8 [2]INLET

PER ISO 11926-1PER ISO 11926-1

65520L0519 • Rev FK • October 2008


Ø14. 4 [0.567]

73 [2.87]

146 [5.75]

77. 2 [3.04]

3.2[0.1 ] 10.4

[0.4]128.8

[5.1]

188.84 [7.43]

96. 7 [3.8 ]



SY STEM PORT B (OUTLET POR T) 345 BAR [5000 PSI] SPLIT FLANGE PER ISO 6162

2X

P104 236E

240. 1 [9.45]

106.62 [4.20]

Ø25.4 [1]

SAE J518 (C ODE 61) with 3/8-16 UNC X 22 [0.866] MINIMUM THREAD DEPTH

26.19 [1.031]

52.37 [2.062]

12.

Ø126.975 ± 0.025

57.25 [2.25]

114. [4.51]

2X

2X

Ø14.4 [0.567] X4

7 [0.5

[4.999 ±0.001]

5 ]

Ø17.5[0.69]

90.5[3.56]

181[7.13]

2X


SAE-C four-bolt housing

PC only control

Radial ported endcap (continued)

The drawings on these pages show a pump with

two-bolt SAE-B and SAE-C mounting flanges. This

pump is also available with a four-bolt SAE-C mounting

flange. The differences are detailed in the drawing

to the right. All other dimensions are common.


SAE-C two-bolt housing

SAE-B two-bolt housing

66 520L0519 • Rev FK • October 2008



electric on/off control/Radial endcap


P106 191E

287.3[11.31]

139.84[5.51]

20°

60.92[2.4]

99.4[3.91]

60.92[2.4]

99.4[3.91]

139.84[5.51]

287.3[11.31]

20°

Radial endcap with electric on/off right control (clockwise) Radial endcap with electric on/off left control (counterclockwise)

269.0[10.62]

141.0[5.55]

20°

83.4[3.28]

76.9[3.03]

141[5.55]

20°

Axial endcap with electric on/off right control (counter clockwise) Axial endcap with electric on/off left control (clockwise)

83.4[3.28]

76.9[3.03]

269.0[10.62]

141.0[5.55]

67520L0519 • Rev FK • October 2008


DisPLaCement LimiteR enDCaPs

P106 728E

Axial endcap - clockwiseRadial endcap - clockwise

Radial endcap - counterclockwise Axial endcap - counterclockwise

207.12[8.2]

167.72[6.6]

146.5[5.8]

241.65[9.5]

162.54[6.4]

207.12[8.2]

167.72[6.6]

146.5[5.8]

241.65[9.5]

162.54[6.4]

207.12[8.2]

167.72[6.6]

146.5[5.8]

241.65[9.5]

162.54[6.4]

207.12[8.2] 167.72

[6.6]

146.5[5.8]

241.65[9.5]

162.54[6.4]


68 520L0519 • Rev FK • October 2008

Series 45 Axial Piston Open Circuit PumpsTechnical InformationFrame F

DesiGn Series 45 Frame F pumps have a dual servo piston design with a cradle-type swashplate set in polymer-coated journal bearings. The bias piston increases swashplate angle. The servo piston decreases swashplate angle. At equal pressure, the larger diameter servo piston overpowers the bias piston. Nine reciprocating pistons displace fluid from the pump inlet to the pump outlet as the cylinder block rotates on the pump input shaft. The block spring holds the piston slippers to the swashplate via the slipper retainer. The cylinder block rides on a bi-metal valve plate optimized for high volumetric efficiency and low noise. Tapered roller bearings support the input shaft and a viton lip-seal protects against shaft leaks.

An adjustable one spool (PC only, not shown) or two spool (LS) control senses system pressure and load pressure (LS controls). The control ports system pressure to the servo piston to control pump output flow.

Frame F cross section

Slipper

LS adjustmen t

PC adjustmen t

LS spoo l

PC spoo l

LS contro l (attached to endcap)

Se rv o piston

Swashplat e

Ta pere d roller bearing

Shaf t seal

Ta pered roller bearing

Input shaf t

C ylinder block

V alv e plate

C ylinder block spring

Piston

Slipper retainer

Bias sprin g

P104 341E Bias piston

69520L0519 • Rev FK • October 2008


sPeCifiCations








see page 17.

Features and options model

feature unit f74B f90C

Maximum Displacement cm³ [in³] 74 [4.52] 90 [5.49]


177.6 [46.9]

198[52.3]



1.178[719]

1.432[874]



0.00630[0.00465]

0.00650[0.00480]


Radial ports 31.8 [70.1]


Mounting SAE B 2 bolt, SAE-C 4 bolt

Auxiliary mounting (See page 77) SAE-A, SAE-B, SAE-BB, SAE-C

System ports (type) 4-bolt split flange


Control types (See page 74) PC, Remote PC, LS, Electric

Shafts (See page 76) Splined 14 tooth, 17 tooth



Ratings model

Rating units f74B f90C

Input speed1 minimum min-1 (rpm) 500 500

continuous 2400 2200

maximum 2800 2600

Working pressure continuous bar [psi] 310 [4495] 260 [3770]

maximum 400 [5800] 350 [5075]


External moment (Me) N•m [lbf•in] 300 [2655]

Thrust in (Tin), out (Tout) N [lbf ] 2900 [650]

Bearing life at 150 bar [2175 psi] B10 hours 31300 17400

at 200 bar [2900 psi] 11100 5700

at 250 bar [3625 psi] 4810 2490

at 280 bar [4060 psi] 3080 1636


Vibratory (continuous) N•m [lbf•in] 3730 [33000]

Shock (max) 13220 [117000]

1. Input speeds are valid at 1 bar absolute [0 in Hg vac] inlet pressure. See Inlet pressure vs. speed charts next page.

Sound levels2

dB(a) 140 bar [2030 psi] 210 bar [3045 psi] 260 bar [3770 psi]

model 1800 min-1(rpm) Rated speed 1800 min-1(rpm) Rated speed 1800 min-1(rpm) Rated speed

F74B 72 76 74 78 75 79

F90C 76 77 76 77 79 79


70 520L0519 • Rev FK • October 2008


PeRfoRmanCe f74B


Flow vs. speed








0

40

80

120

160

200

0 500 1000 1500 2000 25000

10

20

30

40

50

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P104 004E

0

20

40

60

80

100

0 500 1000 1500 2000 25000

20

40

60

80

100

120

Pow

er (k

W)

Speed min (rpm)-1Po

wer

(hp

)P104 005E

140 bar [2030 psi]

210 bar [3045 psi]260 bar [3770 psi]

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P104 015E

0

3

6

9

8

6

4

2

2000 2200 2400 2600 2800 3000


71520L0519 • Rev FK • October 2008


PeRfoRmanCe f90C



Flow vs. speed








0

50

100

150

200

250

0 500 1000 1500 2000 25000

10

20

30

40

50

60

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P104 006E

0

20

40

60

80

100

120

0 500 1000 1500 2000 25000

25

50

75

100

125

150

124 bar [1798 psi]

186 bar [2697 psi]

255 bar [3698 psi]

Pow

er (k

W)

Speed min (rpm)-1

Pow

er (h

p)

P104 007E

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P104 015E

0

3

6

9

8

6

4

2

1800 2000 2200 2400 2600 2800

72 520L0519 • Rev FK • October 2008


oRDeR CoDe

R ProductfR F Frame, variable displacement open circuit pump






BC Pressure compensated control 290-310 bar [4205-4495 psi]


BP Remote pressure compensated control 290-310 bar [4205-4495 psi]


Bs Load sensing / pressure compensating control 290-310 bar [4205-4495 psi]


BB Load sensing / pressure compensating control with internal bleed orifice 290-310 bar [4205-4495 psi]


10–31 100 to 310 bar [1450 to 4495 psi] (074B)

10–26 100 to 260 bar [1450 to 3770 psi] (090C)


10–30 10 to 30 bar [145 to 435 psi]




G Choke orificen None (standard for PC control)

R s P C D e f G H 1 2 3 1 2 3 L m n

– –

J K

73520L0519 • Rev FK • October 2008



H Gain orifice3 Standard

J1 Input shafts1 14 tooth, 12/24 pitch (ANSI B92.1 1970 - Class 5)

s2 17 tooth, 12/24 pitch (ANSI B92.1 1970 - Class 5)

K4 Ø 31.72 mm [1.25 in], straight keyed


a SAE-A, 9-tooth coupling

t SAE-A, 11-tooth coupling

B SAE-B, 13-tooth coupling

v SAE-BB, 15-tooth coupling

C SAE-C, 14-tooth coupling

J3 System port size and locationCode Location Port type inlet size outlet size

2 Radial 4-bolt split-flange 2 in. 1 in.

4 Axial 4-bolt split-flange 2 in. 1 in.



3 SAE-B 2-bolt, SAE O-ring boss housing ports






R s P C D e f G H 1 2 3 1 2 3 L m n

– –

J K

74 520L0519 • Rev FK • October 2008


ContRoLs

Remote PC Control (RP)



f74B 100–310 1450–4495

f90C 100–260 1450–3770


f74B 35 120

f90C 35 135


Specifications

Schematic diagram


f74B 100–310 1450–4495

f90C 100–260 1450–3770


f74B 35 120

f90C 35 135


Specifications

Schematic diagram

LegendB = OutletS = InletL1, L2 = Case drainM2 = System pressure gauge portM4 = Servo pressure gauge port

LegendB = OutletS = InletL1, L2 = Case drainM2 = System pressure gauge portM4 = Servo pressure gauge portX = Remote PC port

Remote PC schematic

M2

L2

S L1 P107 789E

X

X

B

M4

PC schematic

B

M2

L2

S L1 P107 788E

M4


all 20 290

75520L0519 • Rev FK • October 2008





f74B 100–310 1450–4495

f90C 100–260 1450–3770


f74B 35 135

f90C 45 135


Specifications


all 10–30 145–435


f74B 100–310 1450–4495

f90C 100–260 1450–3770


f74B 35 135

f90C 40 135


Specifications


all 10–30 145–435


LegendB = OutletS = InletL1, L2 = Case drainM2 = System pressure gauge portM4 = Servo pressure gauge portX = LS signal port


LS Schematic

M2

L2

S L1

X

X

P107 791E

B

M4

LB Schematic

M2

L2

S L1

X

X

P107 790E

B

M4

76 520L0519 • Rev FK • October 2008


inPut sHafts

Shaft data


s1 14 tooth spline12/24 pitch(ANSI B92.1 1970 - Class 5)

594 [5257]

P104 349E

Ø25.52 MAX [1.005]

8 ± 0.8

[0.31 ± 0.03]

28 ± 0.15 [1.102± 0.006]

Ø31.14 ± 0.08

[1.226 ± 0.003]

14 TEETH 12/24 PITCH 29.634 [1.167] PITCH Ø 30° PRESSURE ANGLEFILLET ROOT SIDE FIT COMPATIBLE WITH

CLASS 5. ALSO MATES WITH FLAT ROOT SIDE FIT

MOUNTING FLANGE

COUPLING MUST NOT PROTRUDE BEYOND THIS POINT

ANSI B92.1-1970

47.6 ± 0.06 [1.874 ± 0.024]

s2 17 tooth spline12/24 pitch(ANSI B92.1 1970 - Class 5)

1044 [9240]

53.97 ± 0.6 [2.125 ± 0.24]

30.75 MAX [1.211]

8 ± 0.8

[0.31 ± 0.03]

39.91 ± 0.09[1.571 ± 0.0035]

Ø37.91 ± 0.09[1.49 ± 0.0035]

35.983 [1.417] PITCH Ø 17 TEETH 12/24 PITCH

30° PRESSURE ANGLE FILLET ROOT SIDE FIT COMPATIBLE WITH


MOUNTINGFLANGE

COUPLING MUST NOT PROTRUDE BEYOND THIS POINT

ANSI B92.1-1970

P104 350E

K4 Ø 31.75 mm [1.25 in]Straight keyed

734 [6495]

Ø31.72 ± 0.02[1.249 ± .001]

35.19 ± 0.13[1.385 ±0.005]

SQ. KEY X 28.58 LG[1.125 ±0.010]

8 ± 0.8[0.31 ± 0.03]

MOUNTINGFLANGE

COUPLING MUST NOTPROTRUDE BEYONDTHIS POINT P104 351E

48 ± 0.6[1.89 ±0.024]

7.938+0.0-0.05

[0.3125 ]+0.0-0.0020

1. See Input shaft torque ratings, page 18 for an explaination of maximum torque.

77520L0519 • Rev FK • October 2008


auxiLiaRy mountinG PaDs Dimensions

sae-a auxiliary mounting pad


spline minimum engagement 13.5 mm [0.53 in] 15 mm [0.59 in]


Dimension a 14.9 mm [0.59 in] 16.1 mm [0.63 in]



spline minimum engagement 14.2 mm [0.56 in] 18.9 mm [0.74 in]


Dimension a 20.7 mm [0.81 in] 12.7 mm [0.5 in]

MOUNTING FLANGE

P104 342E

53.2 [2.094]

106.4 [4.19]

Ø88.62 [3.49]

1.9 [0.077]

58.5 [2.30]

278.07 [10.95]

136.97 [5.39]

5.39 [0.21]

APPROXIMATE CENTER OF GRAVITY

9 TOOTH SPLINE, 16/32 PITCH 14.288 [0.5625] PITCH Ø FILLET ROOT SIDE FIT PER ANSI B92.1, CLASS 6


O-RING SEAL REQUIRED REF 82.27 [3.239] I.D. X 2.62 [0.103] CROSS SECTIONP/N 5000373

MIN COUPLING CLEARANCE

A

0.375-16 UNC-2B THD17.8 [0.70] MIN THD DEPTH 2X

1.3 [0.05] (REAR FLANGE OPTION T)

(REAR FLANGE OPTION A)

8.1 ± 0.7 [0.319 ± 0.028]


275.82 [10.86]

Ø82.6 +0.08 0

[3.252 ] +0.003 0

73 [2.87]

146 [5.75]

87 [3.425]

174 [6.85]

Ø101.65 +0.08 0

[4.002 ] +0.003 0

Ø105.6 [4.16]

0.50-13 UNC-2B THD 19.7 [0.76] MIN THREAD

O-RING SEAL REQUIREDREF 101.32 [3.989] I.D. X 1.78 [0.07] CROSS SECTIONP/N 9004104-0450

P104 343E

MOUNTING FLANGE

275.82 [10.86]

136.24 [5.36]

5.42 [0.21]



(REAR FLANGE OPTION B)

1.32 [0.05]

1.3 [0.051]

54.1 [2.13]

15 TOOTH SPLINE, 16/32 PITCH 23.813 [0.9375] PITCH Ø FILLET ROOT SIDE FIT PER ANSI B92.1, CLASS 6 (REAR FLANGE OPTION V)

DEPTH 2X 11±0.12

[0.433±0.005]


A

APPROXIMATE GRAVITY CENTER OF

273.69 [10.78]



78 520L0519 • Rev FK • October 2008



SpecificationsCoupling 14-tooth

spline minimum engagement 18.3 mm [0.72 in]

maximum torque 339 N•m [3000 lbf•in]


57.3 [2.26]

114.6 [4.51]

57.3 [2.26]

114.6 [4.51]

73.25 [2.88]

146.5 [5.77]

Ø131.57 [5.18]

0.50-13 UNC-2B THD22.7 [0.89] MIN THD DEPTH 4X

O-RING SEAL REQUIREDREF 126.67 [4.987] I.D. X 2.62 [0.103] CROSS SECTIONP/N 5000755

P104 344E

MOUNTING FLANGE

276.69 [10.89]

138.77 [5.46]

5.42 [0.21]



14 ± 0.13 [0.551 ± 0.005]


(REAR FLANGE OPTION C)

1.21 [0.05]

1.3 [0.051]

10.09 [0.4]

MINIMUM COUPLING CLEARANCE

57.1 [2.25]

MINIMUM SHAFT CLEARANCE

Ø127.03 +0.08 0

[5.001 ] +0.003 0

236.14 [9.3]


DisPLaCement LimiteR Series 45 F90C and F74B open circuit pumps are available with an optional adjustable displacement limiter. This adjustable stop limits the pump’s maximum displacement.


Setting rangef90C 45.6 to 90 cm³ [2.78 to 5.49 in³]

f74B 34.1 to 74 cm³ [1.92 to 4.52 in³] P104 345

Displacement per turnf90C 6.8 cm³/rev [0.41 in³/rev]

f74B 6.1 cm³/rev [0.37 in³/rev]

79520L0519 • Rev FK • October 2008


Endcap and shaft machined to accommodate auxiliary

mounting pads; pad and coupling not included.

Conversion kits are available for installation in the field.

aDJustaBLe DisPLaCement LimiteR anD RunninG CoveR

MOUNTING FLANGE

264.2[10.4]

275.82[10.86]

P104 346E

Dimensions

80 520L0519 • Rev FK • October 2008


axiaL PoRteD enDCaP


P104 347E

158.7[6.25]

89 [3.5]

Ø126.975 ± 0.025 [4.999 ± 0.001]

165.14 [6.5]

CASE DRAIN PORT L2

LS SIGNAL PORT X SAE J1926 7/16-20

SYSTEM PORT B AND S

143.2 [5.64]

103.54 [4.08]

121.83 [4.8]

16.44 [0.65]

6.44 [0.25]

12.7[0.5]

227.74 [8.97]

239.74 [9.44]

4X

61.24 [2.41]

53 [2.09]

CASE DRAIN PORT L1 SAE J1926 7/8-14

256.355 [10.09]

45 [1.77]

120.74 [4.75]

CASE DRAIN PORT L2 SAE J1926 7/8-14GAGE PORT M2

SAE J1926/1 7/16-20

SYSTEM PRESSURE

77.34 [3.04]

78.94 [3.11]

40 [1.57]

45 [1.77]

49.7 [1.96]

10.3 [0.41]

SYSTEM PORT S (INLET PORT) 2.00 in -3000 PSISPLIT FLANGE BOSS PER SAE J518 (CODE 61)with 1/2 13 UNCx 27 [1.06] Min.threads

SYSTEM PORT B (OUTLET PORT) 1.00 in -5000 PSISPLIT FLANGE BOSS PER SAE J518 (CODE 61)with 3/8-16 UNCx 22 [0.87] Min.threads

LS SIGNAL PORT X

LS SIGNAL PORT X ALTERNATE

SERVO PRESSURE GAUGE PORT M4 SAE J1926/1 3/4-16

40 [1.57]

45 [1.77]

SYSTEM PORT S (INLET PORT)2.00 in -3000 PSISPLIT FLANGE BOSSPER SAE J518(CODE 61)with 1/2 13 UNCx 27 [1.06] Min.threads


10.3 [0.41]


49.7 [1.96]

LS SIGNAL PORT X

SYSTEM PORT B (OUTLET PORT)1.00 in -5000 PSISPLIT FLANGE BOSSPER SAE J518(CODE 61)with 3/8-16 UNCx 22 [0.87] Min.threads

Clockwise rotation


81520L0519 • Rev FK • October 2008


axiaL PoRteD enDCaP (continued)


P106 628E

57.25 [2.25]

114.5 [4.51]

57.25 [2.25]

114.5 [4.51]

Ø14.3 [0.56]

LS STANDBY

PC PRESSURE

PRESSURE ADJUSTMENT

ADJUSTMENT


CCW CW 91 [3.58]

143.2 [5.64]

165.14 [6.5]

CASE DRAIN PORT L1

LS SIGNAL PORT X ALTERNATE SAE J1926 7/16-20

82 520L0519 • Rev FK • October 2008


RaDiaL PoRteD enDCaP


Clockwise rotation


P104 348E

45 [1.77]


120.74 [7.75]


49.7 [1.96]

10.3 [0.41]

75 [2.95]

82 [3.23]


LS SIGNAL PORT X

49.7 [1.96]

10.3 [0.41]

75 [2.95]

82 [3.23]


LS SIGNAL PORT X

61.24 [2.41]

53 [2.09]


143.2 [5.64]

158.7 [6.25]

103.54 [4.08]

LS SIGNAL PORT X SAE J1926 7/16-20

256.04 [10.08]

212.74 [8.38]

12.7 [0.5]

Ø126.975 ± 0.025 [4.999 ± 0.001]

89 [3.5]

CASE DRAIN PORT L2

5.98 [0.24]

R1 MAX [0.04]

16.44 [0.65]

165.14 [6.5]

133.45 [5.25]

4X

SYSTEM PRESSURE GAUGE PORT M2 SAE J1926 7/16-20

SYSTEM PORT B

SYSTEM PORT S

SYSTEM PORT B (OUTLET PORT)1.00 in -5000 PSISPLIT FLANGE BOSSPER SAE J518(CODE 61)with 3/8-16 UNCx 22 [0.87] Min.threads

83520L0519 • Rev FK • October 2008


RaDiaL PoRteD enDCaP (continued)


P106 629E

57.25 [2.25]

114.5 [4.51]

57.25 [2.25]

114.5 [4.51]

Ø14.3 [0.56]

LS STANDBY PRESSURE ADJUSTMENT

PC PRESSURE ADJUSTMENT

CCW CW

165.14 [6.5]

143.2 [5.64]

LS SIGNAL PORT X ALTERNATE SAE J1926 7/16-20

91 [3.58]

215.74 [8.49]

SYSTEM PORT S (INLET PORT)2.00 in -3000 PSISPLIT FLANGE BOSSPER SAE J518 (CODE 61)with 1/2-13 UNCx 27 [1.06] Min.threads

SERVO PRESSURE

SAE J1926 7/16-20

GAGE PORT M4

84 520L0519 • Rev FK • October 2008

Series 45 Axial Piston Open Circuit PumpsTechnical InformationFrame E

DesiGn Series 45 Frame E pumps have a dual servo piston design with a cradle-type swashplate set in polymer-coated journal bearings. The bias piston increases swashplate angle. The displacement piston decreases swashplate angle. At equal pressure, the larger diameter displacement piston overpowers the bias piston. Nine reciprocating pistons displace fluid from the pump inlet to the pump outlet as the cylinder block rotates on the pump input shaft. The block spring holds the piston slippers to the swashplate via the slipper retainer. The cylinder block rides on a bi-metal valve plate optimized for high volumetric efficiency and low noise. Tapered roller bearings support the input shaft and a viton lip-seal protects against shaft leaks.

An adjustable one spool (PC only, not shown) or two spool (LS) control senses system pressure and load pressure (LS controls). The control ports system pressure to the displacement piston to control pump output flow.

Frame E cross section

Adjustabledisplacementlimiter

Lifting lug

Displacement piston

Displacement piston guide

Swashplate

Input shaft

Shaft seal

Bias piston

Bias spring

Cylinderblock

Bias piston guide

Piston

Slipper

Blockspring

Valve plate


Slipper retainer


LS adjustment

PC adjustment

LS spool

PC spool


P104 001E

85520L0519 • Rev FK • October 2008



feature unit e100B e130B e147C

Maximum Displacement cm³ [in³] 100 [6.10] 130 [7.93] 147 [8.97]


245[64.7]

286 [75.6]

309[81.6]



1.592[972]

2.069[1263]

2.340[1428]



0.0128[0.0094]

0.0128[0.0094]

0.0128[0.0094]


Radial ports 56 [123.5]


Mounting SAE-C

Auxiliary mounting (See page 95) SAE-A, SAE-B, SAE-BB, SAE-C, SAE-CC

System ports (type) 4-bolt split flange


Control types (See page 91) PC, Remote PC, LS, LS with internal bleed

Shafts (See page 93) Splined 13-tooth, 14-tooth, 17-tooth



Ratings model

Rating units e100B e130B e147C

Input speed¹ minimum min-1 (rpm) 500 500 500

continuous 2450 2200 2100

maximum 2880 2600 2475

Working pressure continuous bar [psi] 310 [4495] 310 [4495] 260 [3770]

maximum 400 [5800] 400 [5800] 350 [5075]


External moment (Me) N•m [lbf•in] 455 [4030] 360 [3190] 396 [3500]

Thrust in (Tin), out (Tout) N [lbf ] 2846 [640] 1735 [390] 2113 [475]

Thrust out (Tout) 7740 [1740] 6672 [1500] 7117 [1600]

Bearing life at 140 bar [2030 psi] B10 hours 77 200 32 700 21 600

at 210 bar [3045 psi] 19 800 8400 5500

at 260 bar [3770 psi] 9700 4116 2700

at 310 bar [4495 psi] 5400 2300 —


Vibratory (continuous) N•m [lbf•in] 1920 [17 000]

Shock (max) 6779 [60 000]

1. Input speeds are valid at 1 bar absolute [0 in Hg vac] inlet pressure. See Inlet pressure vs. speed charts.

Sound levels²dB(a) 210 bar [3045 psi] 260 bar [3770 psi] 310 bar [4495 psi]

model 1800 min-1(rpm) Rated speed 1800 min-1(rpm) Rated speed 1800 min-1(rpm) Rated speed

E100B 75 77 77 78 77 80

E130B 77 81 78 81 78 81

E147C 77 78 78 78 — —









see page 17.

86 520L0519 • Rev FK • October 2008


PeRfoRmanCe e100B


Flow vs. speed








0

50

100

150

200

250

0 500 1000 1500 20000

10

20

30

40

50

60

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P104 008E

0

25

50

75

100

125

150

0 500 1000 1500 20000

25

50

75

100

125

150

175

200

Pow

er (k

W)

Speed min (rpm)-1Po

wer

(hp

)P104 009E

140 bar [2030 psi]210 bar [3045 psi]

310 bar [4495 psi]

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P104 017E

0

3

6

9

8

6

4

2

2000 2200 2400 2600 2800 3000 3200


87520L0519 • Rev FK • October 2008


PeRfoRmanCe e130B



Flow vs. speed








0

50

100

150

200

250

300

0 500 1000 1500 20000

10

20

30

40

50

60

70

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P104 010E

0

30

60

90

120

150

0 500 1000 1500 20000

25

50

75

100

125

150

175

200

Pow

er (k

W)

Speed min (rpm)-1

Pow

er (h

p)

P104 011E

310 bar [4495 psi]

210 bar [3045 psi]

140 bar [2030 psi]

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P104 018E

0

3

6

9

8

6

4

2

1800 2000 2200 2400 2600 2800

88 520L0519 • Rev FK • October 2008


PeRfoRmanCe e147C



Flow vs. speed








0

50

100

150

200

250

300

350

0 500 1000 1500 20000

10

20

30

40

50

60

70

80

90

Flo

w (l

/min

)

Speed min (rpm)-1

Flo

w (U

S g

al/m

in)

P104 012E

0

30

60

90

120

150

0 500 1000 1500 20000

25

50

75

100

125

150

175

200

Pow

er (k

W)

Speed min (rpm)-1Po

wer

(hp

)P104 013E

140 bar [2030 psi]

210 bar [3045 psi]260 bar [3770 psi]

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6100% 90% 80%


Inle

t Pr

essu

re (b

ar a

bs)

(psi

gau

ge)

(in H

g v

ac)

P104 019E

0

3

6

9

8

6

4

2

1800 2000 2200 2400 2600 2800

89520L0519 • Rev FK • October 2008


oRDeR CoDe

R ProducteR E Frame, variable displacement open circuit pump







BC* Pressure compensated control 290-310 bar [4205-4495 psi]


BP* Remote pressure compensated control 290-310 bar [4205-4495 psi]


Bs* Load sensing / pressure compensating control 290-310 bar [4205-4495 psi]


BB* Load sensing / pressure compensating control with internal bleed orifice 290-310 bar [4205-4495 psi]

* Use only with 100, and 130 cm³ displacements.


10–31 100 to 310 bar [1450 to 4495 psi] (100B, 130B)

10–26 100 to 260 bar [1450 to 3770 psi] (147C)


10–30 10 to 30 bar [145 to 435 psi]




R s P C D e f G H 1 2 3 1 2 3 L m n

– –

J K

90 520L0519 • Rev FK • October 2008




H Gain orifice3 Standard orifice

J1 Input shafts1 14-tooth, 12/24 pitch (ANSI B92.1 1970 - Class 5)

s2 17-tooth, 12/24 pitch (ANSI B92.1 1970 - Class 5)

s4 13-tooth, 8/16 pitch (ANSI B92.1 1970 - Class 5)

K5 Ø 38.08 mm [1.5 in], straight keyed

s5 14-tooth spline 12/24 pitch (ANSI B92.1 1970 - Class 5 (not available for units with auxiliary mounting pads)


a SAE-A, 9-tooth coupling

t SAE-A, 11-tooth coupling

B SAE-B, 13-tooth coupling

v SAE-BB, 15-tooth coupling

C SAE-C, 14-tooth coupling

w SAE-CC, 17-tooth coupling

J3 System port size and locationCode Location Port type inlet size outlet size

P Radial 4-bolt split-flange 2 ½ in. 1 ¼ in.

L Axial 4-bolt split-flange 2 ½ in. 1 ¼ in.








R s P C D e f G H 1 2 3 1 2 3 L m n

– –

J K

91520L0519 • Rev FK • October 2008


ContRoLs

Remote PC control (RP)



e100B 100–310 1450–4495

e130B 100–310 1450–4495

e147C 100–260 1450–3770


e100B 45 175

e130B 55 175

e147C 60 190


Specifications

Schematic diagram


e100B 100–310 1450–4495

e130B 100–310 1450–4495

e147C 100–260 1450–3770


e100B 45 175

e130B 55 175

e147C 60 190


Specifications

Schematic diagram

LegendB = OutletS = InletL1, L2 = Case drainM2 = System pressure gauge portM4 = Servo pressure gauge port

LegendB = OutletS = InletL1, L2 = Case drainM2 = System pressure gauge portM4 = Servo pressure gauge portX = Remote PC port

Remote PC schematicX

X

M2

M4

L1S

L2

M1

B

P104 022

PC schematic

B

M1

L2

S L1

M4

M2

P104 025


all 20 290

92 520L0519 • Rev FK • October 2008





e100B 100–310 1450–4495

e130B 100–310 1450–4495

e147C 100–260 1450–3770


e100B 45 200

e130B 50 200

e147C 60 200


Specifications


all 10–30 145–435


e100B 100–310 1450–4495

e130B 100–310 1450–4495

e147C 100–260 1450–3770


e100B 45 200

e130B 50 200

e147C 60 200


Specifications


all 10–30 145–435




LB Schematic

M2

X

X

B

M1

L2

S L1

M4

P107 792E

LS SchematicX

X

M2

M4

L1S

L2

M1

B

P104 024

93520L0519 • Rev FK • October 2008


inPut sHafts

Shaft data


s1 14-tooth spline12/24 pitch(ANSI B92.1 1970 - Class 5)

1093 [9675]

48[1.89]

Ø31.14 ± 0.08[1.226 ± 0.003]

33.7 ± 0.5[1.33 ±0.02]

14 TOOTH12/24 PITCH30° PRESSURE ANGLE29.634 [1.167] PITCH |FILLET ROOT SIDE FITCOMPATIBLE WITH ANSI B92.1-1970CLASS 5 ALSO MATES WITHFLAT ROOT SIDE FIT

8 ± 0.8[0.31 ± 0.03]

MAXIMUM FULL SPLINEENGAGEMENTSAUER-DANFOSSRECOMMENDS USINGA COUNTER-BORE INTHE COUPLING TO ENSURESPLINES DO NOTENGAGE BEYOND THISPOINT.

P104 038ECOUPLING MUST NOTPROTRUDE BEYOND THIS POINT


1044 [9240]

34 ± 0.15

Ø36.66 ± 0.08[1.443 ± 0.003]

[1.339 ± 0.006]

54[2.126]

Ø30.75 [1.211] MAX

8 ± 0.8[0.31 ± 0.03]


17 TOOTH12/24 PITCH30° PRESSURE ANGLE35.983 [1.417] PITCH DIAFILLET ROOT SIDE FITCOMPATIBLE WITH


ANSI B92.1-1970

P104 036E


1551 [13 730]

Ø43.94 ± 0.08[1.73 ± 0.003]Ø34.25 [1.348] MAX

42 ± 0.15[1.654 ± 0.006]

67[2.638]


8 ± 0.8[0.31 ± 0.03]

COUPLING MUST NOTPROTRUDE BEYONDTHIS POINTP104 035E


94 520L0519 • Rev FK • October 2008


inPut sHafts(continued)


K5 Ø 38.08 mm [1.5 in]Straight keyed

1161 [10 270]

54 [2.13]

9.525 [0.375] X 38.1 [1.5] LONG SQUARE KEY

Ø38.075 ± 0.025

[1.5 ± 0.0009]

8 ± 0.8

[0.31 ± 0.03] COUPLING MUST NOT PROTRUDE BEYOND THIS POINT P104 037E

Ø42.26 ±0.125 [1.664 ±0.005]


95520L0519 • Rev FK • October 2008


auxiLiaRy mountinG PaDs Dimensions

sae-a auxiliary mounting pad



13.5 mm [0.53 in] 13.5 mm [0.53 in]





14.2 mm [0.56 in] 16.1 mm [0.63 in]


P104 068E

Ø82.6 +0.076 0

[3.252 ] +.003 0

Ø88.62 [3.489]

301.7 [11.878]

1.956 [0.077]

8.1 ± 0.7 [0.319 ±0.028]

COUPLING-SAE A: SPLINE: 11 TOOTH 16/32 PITCH 30° PRESSURE ANGLE 17.463 [0.6875] PITCH DIA FILLET ROOT SIDE FIT PER SAE B92.1-1970 CLASS 6

COUPLING-SAE A: SPLINE: 9 TOOTH 16/32 PITCH 30° PRESSURE ANGLE 4.288 [0.5625] PITCH DIA FILLET ROOT SIDE FIT PER SAE B92.1-1970 CLASS 6

43.261 [1.703] MIN SHAFT CLEARANCE

9.061 [0.357]


MOUNTING FLANGE

O-RING SEAL REQUIRED REFERENCE 82.22 [3.237] I.D.2.62 [0.103] CROSS SECTIONP/N 5000373

Ø10.4 ± 0.12 3/8-16 UNC-2B THD 18 [0.71] MIN THD DEPTH 4X

53.2 [2.094]

2X 106.4

[4.189] 2X

P104 066E

1.956 [0.077]

328.2 [12.921]

Ø107.82 [4.245]

Ø101.65 +0.076 0

[4.002 ] +.003 0

1/2 -13UNC-2B THD 26.25 [1.03] MIN THD DEPTH 4X

COUPLING-SAE B: SPLINE: 13 TOOTH 16/32 PITCH 30° PRESSURE ANGLE 20.638 [0.8125] PITCH DIA FILLET ROOT SIDE FIT PER SAE B92.1-1970 CLASS 6

COUPLING-SAE B-B: SPLINE: 15 TOOTH 16/32 PITCH 30° PRESSURE ANGLE 23.813 [0.9375] PITCH DIA FILLET ROOT SIDE FIT PER SAE B92.1-1970 CLASS 6

9.761 [0.384] MIN COUPLING CLEARANCE

69.461 [2.735] MIN SHAFT CLEARANCE

MOUNTING FLANGE

O-RING SEALREQUIREDREFERENCE101.27 [3.987] I.D.2.62 [0.103] CROSS SECTIONP/N 5000099

146 [5.748]

2X

73 [2.874]

2X



96 520L0519 • Rev FK • October 2008





18.3 mm [0.72 in] 18.3 mm [0.72 in]



P104 067E

328.2 [12.921]

69.461 [2.735]

1.956 [0.077]

Ø127.05 +0.076 0

[5.002 ] +.003 0

Ø134.06 [5.278]

57.3 [2.256]

114.6 [4.512]

57.3 [2.256]

114.6 [4.512]

MOUNTING FLANGE 33.011

[1.30] MINIMUM COUPLING CLEARANCE

COUPLING-SAE C-C: SPLINE:17 TOOTH 12/24 PITCH 30° PRESSURE ANGLE35.992 [1.417] PITCH DIA FILLET ROOT SIDE FIT PER SAE B92.1-1970 CLASS 6

COUPLING-SAE C: SPLINE:14 TOOTH 12/24 PITCH 30° PRESSURE ANGLE29.633 [1.1667] PITCH DIA FILLET ROOT

O-RING SEAL REQUIRED REFERENCE 126.72 [4.989] I.D. 1.78 [0.07] P/N 331256

CROSS SECTION

MIN SHAFT CLEARANCE

Ø12.7 ± 0.12 1/2 -13 UNC-2B THD

26.25 [1.03] MIN THD DEPTH 4X See page 18 for mating pump

pilot and spline dimensions.

Running cover

314.222[12.371]

Mountingflange

P106 079E

Dimensions

97520L0519 • Rev FK • October 2008


DisPLaCement LimiteRs E Frame open circuit pumps are available with an optional adjustable displacement limiter. This adjustable stop limits the pump’s maximum displacement.

Setting rangee100B 40 to 100 cm³ [2.44 to 6.1 in³]

e130B 70 to 130 cm³ [4.27 to 7.93 in³]

e147C 87 to 147 cm³ [5.31 to 8.97 in³]


P104 003

Displacement per turne100B 8.4 cm³/rev [0.51 in³/rev]

e130B 8.4 cm³/rev [0.51 in³/rev]

e147C 8.4 cm³/rev [0.51 in³/rev]

98 520L0519 • Rev FK • October 2008


instaLLation DRawinGs


axial ported endcap, clockwise rotation

P106 176E

DISPLACEMENT LIMITER PORT PER ISO 11926-1 SAE J1926/1 3/4 - 16UNF - 2B

PER ISO 11926-1 SAE J1926/1 1-1/16 - 12UN - 2B

PER ISO 11926-1

275 [10.827]

167.4 [6.591]

191.1 [7.524]

R1 MAX [0.04]

282.315 [11.115]

111.9 [4.406]

Ø126.975 ± 0.025 [4.999 ±0.001]

182.9 [7.201]

132[5.197]

12.7 [0.5]

302.7 MAX [11.92]

50 [1.969]

50 [1.969]

27.3 [1.075]

66.7 [2.626]

98 [3.858]

98 [3.858]

52 [2.047]

76 [2.992]

52 [2.047]

161 [6.339]

SYSTEM PORTS S AND B

CASE DRAIN PORT L1 SPOTFACE DEPTH LS SIGNAL

PORT X

7/16-20UNF-2B SAE J1926/1

SERVO PRESSURE PORT M4

SAE J1926/1 9/16-18UNF-2B

ALTERNATE LS SIGNAL PORT X

LS SIGNAL PORT X

CASE DRAIN PORT L1

SAE J1926/1 1 1/16-12UN-2B

SYSTEM PRESSURE GAGE PORT M1

SAE J1926/1 9/16-18UNF-2B

CASE DRAIN PORT L2

19.09 [0.751] 4X

Ø63.5 [2.50] INLET SYSTEM PORT ‘S’ 172 BAR [2500 PSI] SPLIT FLANGE BOSS PER ISO 6162 SAE J518 CODE 61 WITH 1/2 - 13UNC X 30 [1.181] MIN THD

88.9 [3.50]

66.68 [2.63]

31.75 [1.25]

SYSTEM PRESSURE GAGE PORT ‘M2’ PER ISO 11926 - 1 SAE J1926/1 9/16 - 18UNF - 2B

Ø31.8 [1.25] OUTLET SYSTEM PORT ‘B’ 414 BAR [6000 PSI] SPLIT FLANGE BOSS PER ISO 6162 SAE J518 CODE 62 WITH 1/2 - 13UNC X 25 [0.984] MIN THD

PER ISO 11926-1

PER ISO 11926-1

PER ISO 11926-1

99520L0519 • Rev FK • October 2008


P104 076E

1.87[0.074]

5.2[0.205]

57.25[2.254]

114.5[4.508]

57.25[2.254]

114.5[4.508]

111.9[4.406]

148.05[5.829]

191.1[7.524]

167.4[6.591]


PC PRESSUREADJUSTMENT



ALTERNATELS SIGNALPORT X

SAE J1926/17/16-20UNF-2B

CW

Ø14.3[0.563]4X

PER ISO 11926-1

axial ported endcap, clockwise rotation (continued)instaLLation DRawinGs (continued)


282.32[11.115]

157.4[6.197]

P104 080

PC control

100 520L0519 • Rev FK • October 2008



axial ported endcap, counterclockwise rotation


SYSTEM PRESSUREGAGE PORT ‘M2’PERISO 11926 - 1SAE J1926/19/16 - 18UNF - 2B

Ø63.5[2.50]INLETSYSTEM PORT ‘S’172 BAR [2500 PSI]SPLIT FLANGE BOSSPERISO 6162SAE J518CODE 61WITH 1/2 - 13UNCX 30 [1.181]MIN THD

DISPLACEMENTLIMITER PORTPERISO 11926-1SAE J1926/13/4 - 16UNF - 2B

Ø31.8[1.25]OUTLETSYSTEM PORT ‘B’414 BAR [6000 PSI]SPLIT FLANGE BOSSPERISO 6162SAE J518CODE 62WITH 1/2 - 13UNCX 25 [0.984]MIN THD

66.68[2.63]

31.75[1.25]

88.9[3.50]

50.8[2.00]

SERVOPRESSUREPORT M4

SAE J1926/19/16-18UNF-2B

PER ISO 11926-1

LS SIGNALPORT X

7/16-20UNF-2BSAE J1926/1PER ISO 11926-1

12.7[0.5]

R1 MAX[0.04]

Ø126.975 ± 0.025[4.999 ± 0.001]

111.9[4.406]

191.1[7.524]

282.315[11.115]

302.7 MAX[11.92]

132[5.197]

50[1.969]

50[1.969]

52[2.047]

76[2.992]

98[3.858]

98[3.858]

52[2.047]

161[6.339]

BOTH SIDES

167.4[6.591]

BOTHSIDES


SAE J1926/19/16-18UNF-2B

275[10.827]

SYSTEM PORTS S AND B


BOTH SIDES

27.3[1.075]


66.7[2.626]LS SIGNALPORT X

CASE DRAINPORT "L2"

SAE J1926/11 1/16-12UN-2B

19.09[0.751]4X

P106 177E

182.9[7.201]

CASE DRAINPORT L1

SAE J1926/11 1/16-12UN-2B

PER ISO 11926-1

PER ISO 11926-1

PER ISO 11926-1

101520L0519 • Rev FK • October 2008


114.5[4.508]

57.25[2.254]

5.2[0.205]

114.5[4.508]

57.25[2.254]

1.87[0.074]

148.05[5.829]

111.9[4.406]

Ø14.3[0.563]4X






CCW

P104 078E


axial ported endcap, counterclockwise rotation (continued)


282.32[11.115]

157.4[6.197]

P104 081

PC control

102 520L0519 • Rev FK • October 2008



Radial ported endcap, clockwise rotationinstaLLation DRawinGs (continued)

31.75[1.25]

302.7 MAX[11.92]

111.9[4.406]

167.4[6.591]

Ø126.975 ± 0.025[4.999 ± 0.001]

191.1[7.524]

304[11.969]

251[9.882]

R1 MAX [0.04]

12.7 [0.5]

182.9[7.201]

132[5.197]

27.3[1.075]

66.7[2.626]

100.5[3.957]

100.5[3.957]

52[2.047]

76[2.992]

52[2.047]

161[6.339]

LS SIGNALPORT X

SAE J1926/17/16-20UNF-2B

CASE DRAINPORT L2

SAE J1926/11 1/16-12UN-2B


SAE J1926/19/16-18UNF-2B



SAE J1926/19/16-18UNF-2B

SYSTEMPORT B

SYSTEMPORT S


LS SIGNALPORT X

DISPLACEMENTLIMITER PORT

SAE J1926/13/4-16UNF-2B

CASE DRAINPORT L1

SAE J1926/11 1/16-12UN-2B

19.09 [0.751]4X

P106 178E

PER ISO 11926-1


SAE J1926/19/16-18UNF-2B

PER ISO 11926-1


PER ISO 11926-1

66.68[2.63]

PER ISO 11926-1

PER ISO 11926-1

PER ISO 11926-1

PER ISO 11926-1

103520L0519 • Rev FK • October 2008


57.25[2.254]

114.5[4.508]

57.25[2.254]

114.5[4.508]

2.02 [0.08]

4.86 [0.192]

156.79[6.173]

251[9.882]

191.1[7.524]

167.4[6.591]

111.9[4.406]





SAE J1926/17/16-20UNF-2B


CW

Ø14.3 [0.563]4X

P104 077E

Ø63.5[2.50]INLETSYSTEM PORT ‘S’172 BAR [2500 PSI]SPLIT FLANGE BOSSPER ISO 6162SAE J518CODE 61WITH 1/2 - 13UNCX 30 [1.181]MIN THD

PER ISO 11926-1

Radial ported endcap, clockwise rotation (continued)instaLLation DRawinGs (continued)


282.32[11.115]

157.4[6.197]

P104 082

PC control

104 520L0519 • Rev FK • October 2008



Radial ported endcap, counterclockwise rotation


SYSTEM PRESSUREGAGE PORT ‘M2’PERISO 11926 - 1SAE J1926/19/16 - 18UNF - 2B

DISPLACEMENTLIMITER PORTPERISO 11926-1SAE J1926/13/4 - 16UNF - 2B



SAE J1926/19/16-18UNF-2B

PER ISO 11926-1

LS SIGNALPORT X

7/16-20UNF-2BSAE J1926/1PER ISO 11926-1

PER ISO 11926-1


SAE J1926/19/16-18UNF-2B

PER ISO 11926-1SAE J1926/11-1/16 - 12UN - 2B

CASE DRAIN

PER ISO 11926-1SAE J1926/11-1/16 - 12UN - 2B

CASE DRAIN

66.68[2.63]

31.75[1.25]

251[9.882]

182.9[7.201]

132[5.197]

302.7 MAX [11.92]

304[11.969]

167.4[6.591]

12.7[0.5]

Ø126.975 ± 0.025[4.999 ± 0.001]

111.9[4.406]

R1 MAX[0.039]

27.3[1.075]

66.7[2.626]

100.5[3.957]

100.5[3.957]

52[2.047]

76[2.992]

161[6.339]

52[2.047]

19.09[0.751]4X


191.1[7.524]BOTH SIDES

BOTHSIDES

BOTH SIDES

ALTERNATELS SIGNALPORT X LS SIGNAL

PORT X

SYSTEMPORT B

SYSTEMPORT S

P106 179E

105520L0519 • Rev FK • October 2008


88.9 [3.50]

50.8 [2.00]

2.02 [0.08]

4.86 [0.191] 57.25

[2.254]

114.5 [4.508]

57.25 [2.254]

114.5 [4.508]

111.9 [4.406]

156.79 [6.173]

251 [9.882]

Ø14.3 [0.563] 4X

PC PRESSURE ADJUSTMENT

LS STANDBY PRESSURE ADJUSTMENT


CASE DRAIN PORT L2 SPOTFACE DEPTH


CCW

P104 079E

Ø63.5 [2.50] INLET SYSTEM PORT ‘S’ 172 BAR [2500 PSI] SPLIT FLANGE BOSS PER ISO 6162 SAE J518 CODE 61 WITH 1/2 - 13UNC X 30 [1.181] MIN THD


Radial ported endcap, counterclockwise rotation (continued)


282.32[11.115]

157.4[6.197]

P104 083

PC control

106 520L0519 • Rev FK • October 2008

Series 45 Axial Piston Open Circuit PumpsTechnical InformationNotes

107520L0519 • Rev FK • October 2008

Series 45 Axial Piston Open Circuit PumpsTechnical InformationNotes

sauer-Danfoss mobile Power and Control systems– market Leaders worldwide

Sauer-Danfoss is a comprehensive supplier providing complete systems to the global mobile market.

Sauer-Danfoss serves markets such as agriculture, construction, road building, material handling, municipal, forestry, turf care, and many others.

We offer our customers optimum solutions for their needs and develop new products and systems in close cooperation and partner ship with them.

Sauer-Danfoss specializes in integrating a full range of system components to provide vehicle designers with the most advanced total system design.

Sauer-Danfoss provides comprehensive worldwide service for its products through an extensive network of Global Service Partners strategically located in all parts of the world.

ouR PRoDuCts

Hydrostatic transmissions

Hydraulic power steering

Electric power steering

Electrohydraulic power steering

Closed and open circuit axial piston pumps and motors

Gear pumps and motors

Bent axis motors

Orbital motors

Transit mixer drives

Proportional valves

Directional spool valves

Cartridge valves

Hydraulic integrated circuits

Hydrostatic transaxles

Integrated systems

Fan drive systems

Electrohydraulics

Microcontrollers and software

Electric motors and inverters

Joysticks and control handles

Displays

Sensors

Local address:

Sauer-Danfoss (US) Company2800 East 13th StreetAmes, IA 50010, USAPhone: +1 515 239-6000Fax: +1 515 239-6618

Sauer-Danfoss ApSDK-6430 Nordborg, DenmarkPhone: +45 7488 4444Fax: +45 7488 4400

Sauer-Danfoss-Daikin LTDSannomiya Grand Bldg. 8F2-2-21 Isogami-dori, Chuo-kuKobe, Hyogo 651-0086, JapanPhone: +81 78 231 5001Fax: +81 78 231 5004

Sauer-Danfoss GmbH & Co. OHGPostfach 2460, D-24531 NeumünsterKrokamp 35, D-24539 Neumünster, GermanyPhone: +49 4321 871-0Fax: +49 4321 871 122

www.sauer-danfoss.com520L0519 • Rev FK • October 2008

45 Series E Frame Tech Info (520L0519 Rev FK October 2008)

Documents

frame h

frame fddecember

frame e fimay

frame j dapril

frame j fjjune

frame g bmay

sauerdanfoss logotype

sauerdanfoss group