MARINE DIESEL ENGINES 1GM10 Series Configuration 4-stroke, vertical, raw water-cooled diesel engine Maximum output at crankshaft * 6.7 kW@3600 rpm [9 mhp@3600 rpm] ** 6.6 kW@3600 rpm [9 mhp@3600 rpm] Displacement 0.318 ltr [19.41 cu in] Bore x stroke 75 mm x 72 mm [2.95 in x 2.83 in] Cylinders 1 Combustion system Indirect injection [special swirl type pre-combustion chamber] Aspiration Natural aspiration Starting system Electric starting 12V - 1.0 kW with manual combination Alternator 12V – 60A Cooling system Direct seawater cooling by rubber impeller seawater pump Lubrication system Enclosed, forced lubricating system Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side Dry weight with gear 76 kg [168 lbs] Environmental EU: RCD BSO II EMC Engine mounting Rubber type flexible mounting NOTE: Fuel condition: Density at 15°C = 0.84 g/cm 3 ; 1 kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 25°C at the inlet of the fuel injection pump [ISO 3046-1] ** Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006] Technical data is according to ISO 8665: 2006/3046-1 1GM10 with KM2P-1 marine gear DIMENSIONS Rear view max. 108 mm (4.3 in) min. 88 mm (3.5 in) 156 mm (6.1 in) 209 mm (8.2 in) 179 mm (7.1 in) Exhaust pipe o 45 mm (1.8 in) 554 mm (21.8 in) Right side view 410 mm (16.1 in) 188 mm (7.4 in) 188 mm (7.4 in) 370 mm (14.6 in) 485 mm (19.1 in) 100 mm (3.9 in) 142 mm (5.6 in) EN_DS1GM10_0813 www.yanmar.eu
52
Embed
1GM10 Series 1GM10 Series - · PDF fileMARINE DIESEL ENGINES PERFORMANCE CURVES Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
MARINE DIESEL ENGINES
1GM10 Series
Configuration 4-stroke, vertical, raw water-cooled diesel engine
Maximum output at crankshaft * 6.7 kW@3600 rpm [9 mhp@3600 rpm]
** 6.6 kW@3600 rpm [9 mhp@3600 rpm]
Displacement 0.318 ltr [19.41 cu in]
Bore x stroke 75 mm x 72 mm [2.95 in x 2.83 in]
Cylinders 1
Combustion system Indirect injection [special swirl type pre-combustion chamber]
Aspiration Natural aspiration
Starting system Electric starting 12V - 1.0 kW with manual combination
Alternator 12V – 60A
Cooling system Direct seawater cooling by rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight with gear 76 kg [168 lbs]
Environmental EU: RCD BSO II EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm3; 1 kW = 1.3596 mhp = 1.3410 HP* Fuel temperature 25°C at the inlet of the fuel injection pump [ISO 3046-1]** Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
1GM10 with KM2P-1 marine gear
DIMENSIONS
MARINE DIESEL ENGINES
1GM10 with KM2P-1 marine gear
www.yanmarmarine.com
1GM10 Series
Configuration 4-stroke, vertical, raw water cooled diesel engine
Maximum output at crankshaft * 6.7 kW (9 mhp) / 3600 rpm** 6.6 kW (9 mhp) / 3600 rpm
Combustion system Indirect injection (special swirl type pre-combustion chamber)
Aspiration Natural aspiration
Starting system Electric starting 12 V - 1.0 kW with manual combination
Alternator 12 V – 35 A
Cooling system Direct seawater cooling by rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 71 kg (157 lbs)
Environmental EU RCD, BSO II & EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 25°C at the inlet of the fuel injection pump (ISO 3046-1) **Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665:2006)
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
Rear view
max
. 10
8 m
m (4
.3 in
)m
in.
88 m
m (3
.5 in
)
156 mm(6.1 in)
209 mm(8.2 in)
179 mm(7.1 in)
Exhaust pipeo 45 mm (1.8 in)
554 mm (21.8 in)
Right side view410 mm (16.1 in)
188 mm (7.4 in) 188 mm (7.4 in)
370 mm (14.6 in)
485
mm
(19.
1 in
)
100
mm
(3.9
in)
142 mm(5.6 in)
EN
_DS
1GM
10_0
813
www.yanmar.eu
MARINE DIESEL ENGINES
PERFORMANCE CURVES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Function Digital B-type Panel A-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O X1-2 Push button switch for engine stop O X1-3 Moisture cap for key switch O X1-4 Key switch for ON/OFF (2-position switch) X O1-5 Push button switch for engine start X O2 Alarm lamp unit
2-1 Battery low charge alarm O O2-2 Coolant high temperature alarm O O2-3 Lubricating oil low pressure O O2-4 Water in sail drive seal alarm O O2-5 Water in fuel filter alarm X X2-6 Sea water insufficient flow alarm X X3 Meters
3-1 Lubricating oil pressure meter X X3-2 Coolant temperature meter X X3-3 Hour meter O X3-4 Tachometer O X4 Audible alarm buzzer O O
Note: O = Equipped on panel X = Not equipped on panel
Standard Package• Sensor for instrument panel• Rubber type flexible mounts• Exhaust mixing elbow (L-type)• Alternator 35 A
Optional• A-panel • New B-panel• Digital B-panel• Various extension wire harnesses• Hot water fittings
Accessories
1-1 1-33-4 3-3
2-2 2-3 2-4 2-1
DigitalB-typePanel
140
125
79.5180
165 145
13.5
1-2
Model KM2P-1 KM3V (V-drive) Saildrive (SD20)
Type Constant mesh gear with servo-cone clutch Constant mesh gear with servo-cone clutch Constant mesh gear with dog clutch
Dry weight 10 kg (22 lbs) 19 kg (42 lbs) 30 kg (66 lbs)
Reduction ratio (fwd/asn) 2.21/3.06 2.62/3.06 2.36/3.16 2.61/3.16 3.20/3.16 2.64/2.64
Direction of rotation Clockwise Clockwise Counter clockwise(propeller shaft - fwd) viewed from flywheel side viewed from flywheel side viewed from flywheel side
Dry weight engine and gear/drive 81 kg (179 lbs) 90 kg (198 lbs) 104 kg (229 lbs)
Length engine and gear/drive 554 mm (22 in) 680 mm (27 in) 723 mm (29 in)
Function Digital B-type Panel A-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O X1-2 Push button switch for engine stop O X1-3 Moisture cap for key switch O X1-4 Key switch for ON/OFF (2-position switch) X O1-5 Push button switch for engine start X O2 Alarm lamp unit
2-1 Battery low charge alarm O O2-2 Coolant high temperature alarm O O2-3 Lubricating oil low pressure O O2-4 Water in sail drive seal alarm O O2-5 Water in fuel filter alarm X X2-6 Sea water insufficient flow alarm X X3 Meters
3-1 Lubricating oil pressure meter X X3-2 Coolant temperature meter X X3-3 Hour meter O X3-4 Tachometer O X4 Audible alarm buzzer O O
Note: O = Equipped on panel X = Not equipped on panel
Standard Package• Sensor for instrument panel• Rubber type flexible mounts• Exhaust mixing elbow (L-type)• Alternator 35 A
Optional• A-panel • New B-panel• Digital B-panel• Various extension wire harnesses• Hot water fittings
Accessories
1-1 1-33-4 3-3
2-2 2-3 2-4 2-1
DigitalB-typePanel
140
125
79.5180
165 145
13.5
1-2
Model KM2P-1 KM3V (V-drive) Saildrive (SD20)
Type Constant mesh gear with servo-cone clutch Constant mesh gear with servo-cone clutch Constant mesh gear with dog clutch
Dry weight 10 kg (22 lbs) 19 kg (42 lbs) 30 kg (66 lbs)
Reduction ratio (fwd/asn) 2.21/3.06 2.62/3.06 2.36/3.16 2.61/3.16 3.20/3.16 2.64/2.64
Direction of rotation Clockwise Clockwise Counter clockwise(propeller shaft - fwd) viewed from flywheel side viewed from flywheel side viewed from flywheel side
Dry weight engine and gear/drive 81 kg (179 lbs) 90 kg (198 lbs) 104 kg (229 lbs)
Length engine and gear/drive 554 mm (22 in) 680 mm (27 in) 723 mm (29 in)
Function Digital B-type Panel A-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O X1-2 Push button switch for engine stop O X1-3 Moisture cap for key switch O X1-4 Key switch for ON/OFF (2-position switch) X O1-5 Push button switch for engine start X O2 Alarm lamp unit
2-1 Battery low charge alarm O O2-2 Coolant high temperature alarm O O2-3 Lubricating oil low pressure O O2-4 Water in sail drive seal alarm O O2-5 Water in fuel filter alarm X X2-6 Sea water insufficient flow alarm X X3 Meters
3-1 Lubricating oil pressure meter X X3-2 Coolant temperature meter X X3-3 Hour meter O X3-4 Tachometer O X4 Audible alarm buzzer O O
Note: O = Equipped on panel X = Not equipped on panel
Standard Package• Sensor for instrument panel• Rubber type flexible mounts• Exhaust mixing elbow (L-type)• Alternator 35 A
Optional• A-panel • New B-panel• Digital B-panel• Various extension wire harnesses• Hot water fittings
Accessories
1-1 1-33-4 3-3
2-2 2-3 2-4 2-1
DigitalB-typePanel
140
125
79.5180
165 145
13.5
1-2
Model KM2P-1 KM3V (V-drive) Saildrive (SD20)
Type Constant mesh gear with servo-cone clutch Constant mesh gear with servo-cone clutch Constant mesh gear with dog clutch
Dry weight 10 kg (22 lbs) 19 kg (42 lbs) 30 kg (66 lbs)
Reduction ratio (fwd/asn) 2.21/3.06 2.62/3.06 2.36/3.16 2.61/3.16 3.20/3.16 2.64/2.64
Direction of rotation Clockwise Clockwise Counter clockwise(propeller shaft - fwd) viewed from flywheel side viewed from flywheel side viewed from flywheel side
Dry weight engine and gear/drive 81 kg (179 lbs) 90 kg (198 lbs) 104 kg (229 lbs)
Length engine and gear/drive 554 mm (22 in) 680 mm (27 in) 723 mm (29 in)
Maximum output at crankshaft * 10.0 kW@3600 rpm [13.6 mhp@3600 rpm]
Displacement 0.570 ltr [34.7 cu in]
Bore x stroke 70 mm x 74 mm [2.75 in x 2.91 in]
Cylinders 2
Combustion system Indirect injection
Aspiration Naturel aspiration
Starting system Electric starting 12V - 1.4 kW
Alternator 12V - 125A
Cooling system Fresh water cooling with heat exchanger
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 103 kg [227 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier3
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³; 1 kW = 1.3596 mhp = 1.3410 HP* Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
2YM15 with KM2P-1 marine gear
www.yanmarmarine.com
2YM15 Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 10.3 kW (14 mhp) / 3600 rpm** 10.0 kW (13.6 mhp) / 3600 rpm
Cooling system Fresh water cooling with heat exchanger
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 103 kg (227 lbs)
Environmental EU RCD, BSO II, EPA TIER 3, EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 25°C at the inlet of the fuel injection pump (ISO 3046-1) **Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665 : 2006)Technical data is according to ISO 8665 / 3046
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
Rear view
600.
3 m
m (2
3.6
in)
370 mm (14.6 in)
215 mm (8.5 in)248 mm (9.7 in)
max
. 11
6 m
m (4
.6 in
)m
in.
102
mm
(4.0
in)
176.5 mm (6.9 in)258 mm (10.2 in)178.5 mm (7.0 in)
Exhaust pipeo 51 mm (2.0 in)
613 mm (24.1 in)
463 mm (18.2 in)
115
mm
(4.5
in)
Right side view
528
mm
( 20
.8 in
)
EN
_DS
2YM
15_0
713
www.yanmar.eu
2YM15 with KM2P-1 marine gear
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Direction of rotation Clockwise Counter clockwise(propeller shaft - fwd) viewed from flywheel side viewed from flywheel side
Dry weight engine and gear/drive 113 kg (249 lbs) 134 kg (295 lbs)
Length engine and gear/drive 613 mm (24 in) 793 mm (31 in)
Type of instrument panel Type of instrument panel
Function Digital B-type Panel Keyless B-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O X1-2 Push button switch for engine stop O X1-3 Moisture cap for key switch O X1-4 Rocker switch for Glow/Stop X O1-5 Rocker switch for On/Off/Start X O2 Alarm lamp unit
2-1 Battery low charge alarm O O2-2 Coolant high temperature alarm O O2-3 Lubricating oil low pressure O O2-4 Water in sail drive seal alarm O O2-5 Water in fuel filter alarm X X2-6 Sea water insufficient flow alarm X X3 Meters
3-1 Lubricating oil pressure meter X X3-2 Coolant temperature meter X X3-3 Hour meter O O3-4 Tachometer O O4 Audible alarm buzzer O O
Standard Package• Set of flexible mounts• Exhaust/water mixing elbow L type• V-belt safety cover• Expansion tank for fresh water cooling system• Alternator 12 V - 80 A• Electric stop solenoid• Operation Manual
Optional• Digital B Panel Horizontal• 3M / 6M Extension Wire harness• High Riser Mixing Elbow U type (Instead of L-Elbow)• Hotwaterkit with cocks• Dual Harness (For 2nd Station)• Cone Nut Kit SD20 (For SD20)
Accessories
165+0,5-0,5
125
+0,5
-0,5
140
+0,5
-0,5
180+0,5-0,5
145
,2±14
2 +0,2-0,2
MAX +HARNESS72
PANEL WITH COVERFOIL
RUBBER SEAL, B PANEL1-4
3-3 1-53-4
2-1
2-4
2-3
2-2
1:1
LABEL IMPULSE SETTINGS
GAUGE LABEL
2
4
1-5
KeylessB panel
PERFORMANCE CURVES
EN
_DS
2YM
15_0
713
www.yanmar.eu
Standard engine package• Set of flexible mounts • Exhaust mixing elbow [L-type]• V-belt safety cover • Expansion tank for fresh water cooling system • Alternator 12V - 125A • Electric stop solenoid • Operation manual • B20-panel• Sensor for instrument panel
Optional accesories• Extension wire harness [4m, 6m, 10m]• High-riser mixing elbow [instead of L-elbow] • Hot water kit with cocks • Second station harness• Propeller cone nut kit SD20
ACCESORIES
MARINE GEARS / DRIVE
Model
Type
Dry weight
Reduction ratio [fwd/asn]
Propeller speed [fwd/asn]
Direction of rotation
[propeller shaft - fwd]
Dry weight engine and gear/drive
Length engine and gear/drive
KM2P-1
Constant mesh gear with servo-cone clutch
10 kg [22 lbs]
2.21/3.06 2.62/3.06 3.22/3.06
1629/1176 1374/1176 1118/1176
Clockwise
viewed from flywheel side
113 kg [249 lbs]
613 mm [24 in]
Saildrive [SD20]
Constant mesh gear with dog clutch
30 kg [66 lbs]
2.64/2.64
1363/1363
Counterclockwise
viewed from flywheel side
134 kg [295 lbs]
793 mm [31 in]
NOTE: All data subject to change without notice. Text and illustrations are not binding.
Maximum output at crankshaft 28.7 kW@3000 rpm [38.5 mhp@3000 rpm]
Displacement 1.642 ltr [100 cu in]
Bore x stroke 88 mm x 90 mm [3.46 in x 3.54 in]
Cylinders 3 in line
Combustion system Direct injection
Aspiration Natural aspiration
Starting system Electric starting 12V - 1.4 kW
Alternator 12V – 125A
Cooling system Fresh water cooling by centrifugal fresh water pump and
rubber impeller sea water pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 173 kg [381 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier 3
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm3: 1 kW = 1.3596 mhp = 1.3410 HPFuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
3JH5E with KM35A marine gear
DIMENSIONS
MARINE DIESEL ENGINES
3JH5E with KM35A marine gear
www.yanmarmarine.com
3JH5E Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft 28.7 kW (38,5 mhp) / 3000 rpm
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller sea water pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 173 kg (381 lbs)
Environmental EU RCD, EPA TIER 3, EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm3
Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665 : 2006)
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
Right side viewFront view
622.
6 m
m (2
4.5
in)
517.6 mm (20.4 in)
max
. 11
0 m
m (4
.3 in
)m
in. 1
00 m
m (3
.9 in
)
420 mm (16.5 in)
Mixing elbowo 76 mm (3.0 in)
191.
2 m
m (7
.5 in
)
190 mm(7.5 in)412 mm (16.2 in)
168 mm(6.6 in)
770 mm (30.3 in)
EN
_DS
3JH
5E_0
713
www.yanmar.eu
MARINE DIESEL ENGINES
PERFORMANCE CURVES
www.yanmarmarine.com Yanmar Europe BV
Marine Gears/Drive
Performance Curves (Output is according ISO 8665)
Maximum output at crankshaft
Power Torque
Maximum output at prop shaft
Propeller power curve
Fuel Consumption
Instrument Panels
Standard Features• Set of flexible engine mounts• Exhaust mixing elbow (L-type)• V-belt safety cover• Fresh water expansion tank• Alternator 12 V - 80 A• Electric stop solenoid• Operation manual
Optional• Digital B panel keyless• Digital C panel with key switch or key less• Second Alternator 12V80A, 12V130A or 24V75A • High riser mixing (Instead of L-Elbow)• 4M, 6M, 10M Extension Wire harness• Hot water kit with cocks• Second station harness
Extra for all C-panels: Coolant temperature gauge, Lubricating oil pressure gauge
Propeller-curve calculated with exponent 3
DigitalC-panelkeyswitch
Version: 2011-07
www.yanmarmarine.com Yanmar Europe BV
Marine Gears/Drive
Performance Curves (Output is according ISO 8665)
Maximum output at crankshaft
Power Torque
Maximum output at prop shaft
Propeller power curve
Fuel Consumption
Instrument Panels
Standard Features• Set of flexible engine mounts• Exhaust mixing elbow (L-type)• V-belt safety cover• Fresh water expansion tank• Alternator 12 V - 80 A• Electric stop solenoid• Operation manual
Optional• Digital B panel keyless• Digital C panel with key switch or key less• Second Alternator 12V80A, 12V130A or 24V75A • High riser mixing (Instead of L-Elbow)• 4M, 6M, 10M Extension Wire harness• Hot water kit with cocks• Second station harness
Extra for all C-panels: Coolant temperature gauge, Lubricating oil pressure gauge
Propeller-curve calculated with exponent 3
DigitalC-panelkeyswitch
Version: 2011-07
www.yanmarmarine.com Yanmar Europe BV
Marine Gears/Drive
Performance Curves (Output is according ISO 8665)
Maximum output at crankshaft
Power Torque
Maximum output at prop shaft
Propeller power curve
Fuel Consumption
Instrument Panels
Standard Features• Set of flexible engine mounts• Exhaust mixing elbow (L-type)• V-belt safety cover• Fresh water expansion tank• Alternator 12 V - 80 A• Electric stop solenoid• Operation manual
Optional• Digital B panel keyless• Digital C panel with key switch or key less• Second Alternator 12V80A, 12V130A or 24V75A • High riser mixing (Instead of L-Elbow)• 4M, 6M, 10M Extension Wire harness• Hot water kit with cocks• Second station harness
Extra for all C-panels: Coolant temperature gauge, Lubricating oil pressure gauge
Propeller-curve calculated with exponent 3
DigitalC-panelkeyswitch
Version: 2011-07
EN
_DS
3JH
5E_0
713
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
Standard engine package• Set of flexible engine mounts • Exhaust mixing elbow [L-type] • V-belt safety cover • Fresh water expansion tank• Alternator 12V - 125A • Electric stop solenoid • Operation manual• B20-panel• Sensor for instrument panel
Optional accesories• Second alternator 12V - 130A or 24V - 75A incl. smart regulator• High-riser mixing elbow [instead of L-elbow]• Hot water kit with cocks • Second station harness• C30-panel• Sensor for C30-panel• Extension saildrive leg [75 mm]• Extension wire harness [4m, 6m 10m]• Propeller cone nut kit SD60
Maximum output at crankshaft * 15.3 kW@3600 rpm [21 mhp@3600 rpm]
Displacement 0.854 ltr [52.1 cu in]
Bore x stroke 70 mm x 74 mm [2.8 in x 2.9 in]
Cylinders 3
Combustion system Indirect injection
Aspiration Naturel aspiration
Starting system Electric starting 12V - 1.4 kW
Alternator 12V - 125A
Cooling system Fresh water cooling with heat exchanger
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 110 kg [243 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier3
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³; 1 kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665:2006]Technical data is according to ISO 8665:2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
3YM20 with KM2P-1 marine gear
www.yanmarmarine.com
3YM20 Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 15.3 kW (21 mhp) / 3600 rpm
Cooling system Fresh water cooling with heat exchanger
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 120 kg (265 lbs)
Environmental EU RCD, BSO II, EPA TIER 3, EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665)Technical data is according to ISO 8665 / 3046
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
Rear view Right side view
600.
3 m
m (2
3.6
in)
370 mm (14.6 in)
215 mm (8.5 in)248 mm (9.7 in)
max
. 11
6 m
m (4
.6 in
)m
in.
102
mm
(4.0
in)
178.5 mm (7.0 in)336 mm (13.2 in)178.5 mm (7.0 in)
Exhaust pipeo 51 mm (2.0 in)
693.5 mm (27.3 in)
463 mm (18.2 in)
115
mm
(4.5
in)
EN
_DS
3YM
20_0
813
www.yanmar.eu
3YM20 with KM2P-1 marine gear
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
www.yanmarmarine.com
Version: 2011-07
Yanmar Europe BV
Marine Gears/Drive
Instrument Panels
Model KM2P-1 Saildrive (SD20)
Type Constant mesh gear with servo-cone clutch Constant mesh gear with dog clutch
Dry weight 10 kg (22 lbs) 30 kg (66 lbs)
Reduction ratio (fwd/asn) 2.21/3.06 2.62/3.06 3.22/3.06 2.64/2.64
Standard Package• Set of flexible mounts• Exhaust mixing elbow (L-type)• V-belt safety cover• Expansion tank for fresh water cooling system• Alternator 12 V - 80 A• Electric stop solenoid• Operation Manual
Optional• Digital B Panel Horizontal• 3M / 6M Extension Wire harness• High Riser Mixing Elbow (Instead of L-Elbow)• Hot Water Kit 90/180 Cocks• Dual Harness (For 2nd Station)• Cone Nut Kit SD20 (For SD20)
Accessories
1-1 1-33-4 3-3
2-2 2-3 2-4 2-1
DigitalB-typePanel
140
125
79.5180
165 145
13.5
1-2
165+0,5-0,5
125
+0,5
-0,5
140
+0,5
-0,5
180+0,5-0,5
145
,2±14
2 +0,2-0,2
MAX +HARNESS72
PANEL WITH COVERFOIL
RUBBER SEAL, B PANEL1-4
3-3 1-53-4
2-1
2-4
2-3
2-2
1:1
LABEL IMPULSE SETTINGS
GAUGE LABEL
2
4
1-5
KeylessB panel
Type of instrument panel Type of instrument panel
Function Digital B-type Panel Keyless B-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O X1-2 Push button switch for engine stop O X1-3 Moisture cap for key switch O X1-4 Rocker switch for Glow/Stop X O1-5 Rocker switch for On/Off/Start X O2 Alarm lamp unit
2-1 Battery low charge alarm O O2-2 Coolant high temperature alarm O O2-3 Lubricating oil low pressure O O2-4 Water in sail drive seal alarm O O2-5 Water in fuel filter alarm X X2-6 Sea water insufficient flow alarm X X3 Meters
3-1 Lubricating oil pressure meter X X3-2 Coolant temperature meter X X3-3 Hour meter O O3-4 Tachometer O O4 Audible alarm buzzer O O
Note: O = Equipped on panel X = Not equipped on panel
PERFORMANCE CURVES
EN
_DS
3YM
20_0
813
www.yanmar.eu
MARINE GEARS / DRIVE
Model
Type
Dry weight
Reduction ratio [fwd/asn]
Propeller speed [fwd/asn]
Direction of rotation
[propeller shaft - fwd]
Dry weight engine and gear/drive
Length engine and gear/drive
KM2P-1
Constant mesh gear with servo-cone clutch
10 kg [22 lbs]
2.21/3.06 2.62/3.06 3.22/3.06
1629/1176 1374/1176 1118/1176
Clockwise
viewed from flywheel side
120 kg [265 lbs]
693 mm [27 in]
Saildrive [SD20]
Constant mesh gear with dog clutch
30 kg [66 lbs]
2.64/2.64
1364/1364
Counter clockwise
viewed from flywheel side
140 kg [309 lbs]
873 mm [34 in]
NOTE: All data subject to change without notice. Text and illustrations are not binding.
Standard engine package• Set of flexible mounts • Exhaust mixing elbow [L-type] • V-belt safety cover • Expansion tank for fresh water cooling system • Alternator 12V - 125A • Electric stop solenoid • Operation manual • Sensor for instrument panel• B20-panel
ACCESORIES
Optional accesories• Extension wire harness [4m, 6m, 10m]• High-riser mixing elbow [instead of L-elbow] • Hot water kit with cocks • Second station harness• Propeller cone nut kit SD20
Maximum output at crankshaft * 21.3 kW@3600 rpm [29.1 mhp@3600 rpm]
Displacement 1.115 ltr [68 cu in]
Bore x stroke 76 mm x 82 mm [2.9 in x 3.2 in]
Cylinders 3
Combustion system Indirect injection
Aspiration Naturel aspiration
Starting system Electric starting 12V - 1.4 kW
Alternator 12V - 125A
Cooling system Fresh water cooling with heat exchanger
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 123 kg [271 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier3
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³; 1 kW = 1.3596 mhp = 1.3410 HP* Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665:2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
3YM30 with KM2P-1 marine gear
www.yanmarmarine.com
3YM30 Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 21.3 kW (29.1 mhp) / 3600 rpm
Cooling system Fresh water cooling with heat exchanger
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 123 kg (271 lbs)
Environmental EU RCD, BSO II, EPA TIER 3, EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665)
Technical data is according to ISO 8665 / 3046
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
115
mm
(4.5
in)
370 mm (14.6 in)
545
mm
(21.
5 in
)
215 mm (8.5 in)247 mm (9.7 in)
max
. 11
6 m
m (4
.6 in
)m
in.
102
mm
(4.0
in)
182 mm (7.2 in)
355mm(14.0 in)
178.5 mm(7.0 in)
Exhaust pipeo 51 mm (2.0 in)
715.5 mm (28.2 in)
462 mm (18.2 in)
Right side viewRear viewE
N_D
S3Y
M3
0_0
813
www.yanmar.eu
3YM30 with KM2P-1 marine gear
MARINE DIESEL ENGINES
PERFORMANCE CURVES
EN
_DS
3YM
30
_081
3
www.yanmar.eu
Standard engine package• Set of flexible mounts • Exhaust mixing elbow [L-type] • V-belt safety cover • Expansion tank for fresh water cooling system • Alternator 12V - 125A • Electric stop solenoid • Operation manual • Sensor for instrument panel• B20-panel
ACCESORIES
MARINE GEARS / DRIVE
Model
Type
Dry weight
Reduction ratio [fwd/asn]
Propeller speed [fwd/asn]
Direction of rotation
[propeller shaft - fwd]
Dry weight engine and gear/drive
Length engine and gear/drive
KM2P-1
Constant mesh gear with servo-cone clutch
10 kg [22 lbs]
2.21/3.06 2.62/3.06 3.22/3.06
1629/1176 1374/1176 1181/1176
Clockwise
viewed from flywheel side
133 kg [293 lbs]
715 mm [28 in]
Saildrive [SD20]
Constant mesh gear with dog clutch
30 kg [66 lbs]
2.64/2.64
1364/1364
Counterclockwise
viewed from flywheel side
153 kg [337 lbs]
895 mm [35 in]
NOTE: All data subject to change without notice. Text and illustrations are not binding.
Optional accesories: • Extension wire harness [4m, 6m, 10m]• High riser mixing elbow [instead of L-elbow] • Hot water kit with cocks• Second station harness• Propeller cone nut kit SD20
Maximum output at crankshaft 110 kW@4000 rpm [150 mhp@4000 rpm]
132 kW@4000 rpm [180 mhp@4000 rpm]
Displacement 1.995 ltr [122 cu in]
Bore x stroke 84 mm x 90 mm [3.31 in x 3.54 in]
Cylinders 4 in line
Combustion system Direct injection with Bosch Common Rail System
Aspiration Turbocharger + charge air cooler
Low Idle rpm 650 - 950 rpm [adjustable]
Electric system 12V
Alternator 12V - 150A
Start-assist Glow-plug system
Cooling system Fresh water cooling by centrifugal fresh water pump
Sea water cooling by rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from fl ywheel side
Dry weight without gear 269 kg [593 lbs]
Environmental EU: RCD EMC BSO II
US: EPA Tier3
SOLAS MED 96/98/EC
Engine mounting Rubber type fl exible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
4BY3-180 with KMH41A marine gear
DIMENSIONS
Type 4BY3-1504BY3-180
Configuration 4-cylinder in line, 4-stroke, water cooled diesel engine
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665:2006)
Dimensions
4BY3-180 with KMH41A marine gear
www.yanmarmarine.com
FRONT VIEW RIGHT SIDE VIEW
Version 2012-10
EN
_DS
4BY
3_0
413
www.yanmar.eu
MARINE DIESEL ENGINESType 4BY3-150
4BY3-180
Performance Curves
Drive systems
ModelTypeDry WeightReduction Ratio 1,53 2,04 2,45 2,62Direction of rotationLub oil specificationsDry weight - engine & gear
Control system "Classic"
Engine Accesories
Standard engine package Single pole, 150A AlternatorL-type exhaust elbowAutomatic glow-plug controllerFlexible engine mountingAnalogue throttle with redundancy function
Optional accesories High-riser mixing elbowExhaust-side 2nd dipstickElectric gearshiftTrolling on gearbox [mechanical and Electrical]NMEA2000 Digital displayFull NMEA2000 electronic control system [CAN-bus]
Clockwise / Counterclockwise viewed from the stern
0
20
40
60
80
100
120
140
1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500
Pow
er [k
W]
Crankshaft speed [RPM]
4BY3-180
4BY3-150
0
50
100
150
200
250
300
350
400
1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500
Torq
ue [N
m]
Crankshaft speed [RPM]
4BY3-150
4BY3-180
Version 2012-10
Type 4BY3-1504BY3-180
Performance Curves
Drive systems
ModelTypeDry WeightReduction Ratio 1,53 2,04 2,45 2,62Direction of rotationLub oil specificationsDry weight - engine & gear
Control system "Classic"
Engine Accesories
Standard engine package Single pole, 150A AlternatorL-type exhaust elbowAutomatic glow-plug controllerFlexible engine mountingAnalogue throttle with redundancy function
Optional accesories High-riser mixing elbowExhaust-side 2nd dipstickElectric gearshiftTrolling on gearbox [mechanical and Electrical]NMEA2000 Digital displayFull NMEA2000 electronic control system [CAN-bus]
Clockwise / Counterclockwise viewed from the stern
0
20
40
60
80
100
120
140
1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500
Pow
er [k
W]
Crankshaft speed [RPM]
4BY3-180
4BY3-150
0
50
100
150
200
250
300
350
400
1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500
Torq
ue [N
m]
Crankshaft speed [RPM]
4BY3-150
4BY3-180
Version 2012-10
PERFORMANCE CURVES
DRIVE SYSTEMS
CONTROL SYSTEM “CLASSIC”
Optional accesories• High-riser mixing elbow [instead of L-elbow]• Exhaust-side 2nd dipstick• Electric gearshift• Trolling on gearbox [mechanical and electrical]• NMEA2000 digital display• Full NMEA2000 electronic control system [CAN-bus]
Standard engine package• Single pole, 150A Alternator• Exhaust mixing elbow [L-type]• Automatic glow-plug controller• Flexible engine mounting• Analogue throttle with redundancy function
ENGINE ACCESORIES
EN
_DS
4BY
3_0
413
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
KMH41A [down angle 8°]
Hydraulic Actuated Multi-friction disc clutch
34 kg excl. foot and cooler [=15.5 kg]
1.53
Clockwise & Counterclockwise viewed from the stern
Maximum output at crankshaft 110 kW@4000 rpm [150 mhp@4000 rpm]
132 kW@4000 rpm [180 mhp@4000 rpm]
Displacement 1.995 ltr [122 cu in]
Bore x stroke 84 mm x 90 mm [3.31 in x 3.54 in]
Cylinders 4 in line
Combustion system Direct injection with Bosch Common Rail System
Aspiration Turbocharger + charge air cooler
Low Idle rpm 650 - 950 rpm [adjustable]
Electric system 12V
Alternator 12V - 150A
Start-assist Glow-plug system
Cooling system Fresh water cooling by centrifugal fresh water pump
Sea water cooling by rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from fl ywheel side
Dry weight without gear 269 kg [593 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier3
Engine mounting Rubber type fl exible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
Type 4BY3-150Z4BY3-180Z
Configuration 4-cylinder in line, 4-stroke, water cooled diesel engine
ModelTypeDry WeightReduction Ratio 1,36 1,5 1,65Propeller speed 2941 2667 2424Direction of rotationLub oil specificationsDry weight - engine & gear1 - Inner and outer transom surface must be parallel within 3mm in area covered by transom plates and remain within transom thickness limits.
2 - Area covered by gimbal housing assembly must be flat to within 1.6mm.
3 - Area covered by inner transom plate must be flat to within 3.2mm
4 - Transom angle: 13° to 16°
5 - Also available with Bravo X-2 drive's, please contact your local supplier for support.
Control system "Classic"
Engine Accesories
Standard engine package Single pole, 150A AlternatorHigh Riser mixing exhaust elbowAutomatic glow-plug controllerFlexible engine mountingAnalogue throttle with redundancy function
Optional accesories Through transom exhaustExhaust-side 2nd dipstickElectric gearshiftNMEA2000 Digital displayVarious monitoring gaugesFull NMEA2000 electronic control system [CAN-bus]
Propellers Propeller size 20" - 22" - 24" - 26" - 28"Propellers with cup 24"- 26"
www.yanmarmarine.com
Mercury High Performance Gearlube373 kg
API class: GL5 SAE grade #80W90 or QuickSilver High Performance Gearlube388 kg
Mercruiser Bravo 1 Steerable Z-drive with single propellerMechanical cone-clutch type Sterndrive
59 kg [drive] / 48 kg [Transom + trim-pump] / 8 kg [Propeller]
Clockwise / Counterclockwise viewed from the stern
ModelTypeDry WeightReduction Ratio 1,36 1,5 1,65Propeller speed 2941 2667 2424Direction of rotationLub oil specificationsDry weight - engine & gear1 - Inner and outer transom surface must be parallel within 3mm in area covered by transom plates and remain within transom thickness limits.
2 - Area covered by gimbal housing assembly must be flat to within 1.6mm.
3 - Area covered by inner transom plate must be flat to within 3.2mm
4 - Transom angle: 13° to 16°
5 - Also available with Bravo X-2 drive's, please contact your local supplier for support.
Control system "Classic"
Engine Accesories
Standard engine package Single pole, 150A AlternatorHigh Riser mixing exhaust elbowAutomatic glow-plug controllerFlexible engine mountingAnalogue throttle with redundancy function
Optional accesories Through transom exhaustExhaust-side 2nd dipstickElectric gearshiftNMEA2000 Digital displayVarious monitoring gaugesFull NMEA2000 electronic control system [CAN-bus]
Propellers Propeller size 20" - 22" - 24" - 26" - 28"Propellers with cup 24"- 26"
www.yanmarmarine.com
Mercury High Performance Gearlube373 kg
API class: GL5 SAE grade #80W90 or QuickSilver High Performance Gearlube388 kg
Mercruiser Bravo 1 Steerable Z-drive with single propellerMechanical cone-clutch type Sterndrive
59 kg [drive] / 48 kg [Transom + trim-pump] / 8 kg [Propeller]
Clockwise / Counterclockwise viewed from the stern
ZT370 Steerable Z-drive with duo-propellerHydraulic Actuated Multi-friction disc Sterndrive
69 kg [drive] / 46 kg [Transom + trim-pump] / 15 kg [Propellers]
0
20
40
60
80
100
120
140
1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500
Pow
er [k
W]
Crankshaft speed [RPM]
4BY3-180
4BY3-150
0
50
100
150
200
250
300
350
400
1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500
Torq
ue [N
m]
Crankshaft speed [RPM]
4BY3-150
4BY3-180
Version 2012-10
PERFORMANCE CURVES
CONTROL SYSTEM “CLASSIC”
Optional accesories• Through transom exhaust• Exhaust-side 2nd dipstick• Electric gearshift• NMEA2000 digital display• Various monitoring gauges• Full NMEA2000 electronic control system [CAN-bus]
Propellers• Propeller size
20” - 22” - 24” - 26” - 28”• Propellers with cup
24”- 26”
Standard engine package• Single pole, 150A Alternator• High-riser mixing exhaust elbow• Automatic glow-plug controller• Flexible engine mounting• Analogue throttle with redundancy function
ENGINE ACCESORIES
EN
_DS
4BY
3Z_0
813
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
DRIVE SYSTEMS
1 - Inner and outer transom surface must be parallel within 3mm in area covered by transom plates and remain within transom thickness limits.2 - Area covered by gimbal housing assembly must be fl at to within 1.6 mm.3 - Area covered by inner transom plate must be fl at to within 3.2 mm.4 - Transom angle: 13° to 16°.5 - Also available with Bravo X-2 drive’s, please contact your local supplier for support.
ZT370 Steerable Z-drive with duo-propeller
Hydraulic Actuated Multi-friction disc Sterndrive
69 kg [drive] / 46 kg [Transom + trim-pump] / 15 kg [Propellers]
Maximum output at crankshaft * 89.1 kW@3800 rpm [121 mhp@3800 rpm]
** 91.9 kW@3800 rpm [125 mhp@3800 rpm]
Displacement 1.995 ltr [122 cu in]
Bore x stroke 84 mm x 90 mm [3.31 in x 3.54 in]
Cylinders 4
Combustion system Direct injection
Aspiration Turbocharged with intercooler
Starting system Electric starting 12V - 1.4 kW
Alternator 12V - 125A
Cooling system Fresh water cooling by centrifugal fresh water pump
and rubber impeller sea water pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from stern
Dry weight without gear 229 kg [504.8 lbs]
Environmental EU: RCD BSO II EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm3; 1 kW = 1.3596 mhp = 1.3410 HP* Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]** Fuel temperature 25°C at the inlet of the fuel injection pump [ISO 3046-1]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
4JH3-DTE with ZF25A marine gear
www.yanmarmarine.com
4JH3-DTE Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 89.1 kW (121 mhp) / 3800 rpm** 91,9 kW (125 mhp) / 3800 rpm
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller sea water pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from stern
Dry weight without gear 229 kg (504.8 lbs)
Environmental EU RCD, BSO II, EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665 : 2006)** Fuel temperature 25°C at the inlet of the fuel injection pump (ISO 3046-1)
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
Right side view
202
mm
(8 in
)
490 mm (19.3 in)
265 mm (10.4 in)315.5 mm (12.4 in)
max
. 11
0 m
m (4
.3 in
)m
in.
100
mm
(3.9
in)
143.2 mm(5.6 in)560 mm (22 in)
167.1 mm(6.6 in)
Mixing elbowo 76 mm (3.0 in)
1001.3 mm (39.4 in)
Rear view580.5 mm (22.9 in)
660.
3 m
m (2
6 in
)
EN
_DS
4JH
3-D
TE
_071
3
www.yanmar.eu
4JH3-DTE with ZF25A marine gear
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Function Digital B-type Panel Digital C-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O O1-2 Push button switch for engine stop O O1-3 Moisture cap for key switch O O2 Alarm lamp unit
2-1 Battery low charge alarm O O2-2 Coolant high temperature alarm O O2-3 Lubricating oil low pressure O O2-5 Water in fuel filter alarm X O2-6 Sea water insufficient flow alarm X O3 Meters
3-1 Lubricating oil pressure meter X O3-2 Coolant temperature meter X O3-3 Hour meter O O3-4 Tachometer O O4 Audible alarm buzzer O O
Note: O = Equipped on panel X = Not equipped on panel
Standard Package• Set of flexible mounts• Exhaust mixing elbow (L-type)• Expansion tank for fresh water cooling system• Alternator 12 V - 80 A• Electric stop solenoid
Optional• Digital B-type instrument panel• Digital C-type instrument panel • Exhaust mixing elbow, U-type (high riser) • Various extension wire harnesses (4M, 6M, 10M)• Hot water fitting with cocks• Secondary 80 A alternator
Direction of rotation Clockwise & counter Clockwise or counterclockwise Clockwise & counter clockwise(propeller shaft - fwd) clockwise viewed from stern viewed from flywheel side viewed from stern
Dry weight engine 260 kg (573 lbs) 237 kg (522 lbs) 259 kg (571 lbs)and gear/drive
Length engine 886 mm (35 in) 903 mm (35.6 in) 1001 mm (39 in)and gear/drive
DigitalC-typePanel
PERFORMANCE CURVES
Optional• High-riser mixing elbow [instead of L-elbow]• Extension wire harness [4m, 6m, 10m]• Hot water fitting with cocks• Second station harness• C30-panel• Sensor for C30-panel
Standard Package• Set of flexible mounts• Exhaust mixing elbow [L-type]• Expansion tank for fresh water cooling system• Alternator 12V - 125A• Electric stop solenoid • Operation manual• B20-panel• Sensor for instrument panel
ACCESSORIES
EN
_DS
4JH
3-D
TE
_071
3
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
Maximum output at crankshaft * 80.9 kW@3200 rpm [110 mhp@3200 rpm]
Displacement 1.995 ltr [121.7 cu in]
Bore x stroke 84 mm x 90 mm [3.31 in x 3.54 in]
Cylinders 4, 4-valves per cylinder
Combustion system Direct injection
Aspiration Turbocharged with intercooler
Starting system Electric starting 12V - 1.4 kW
Alternator 12V - 125A
Cooling system Fresh water cooling by centrifugal water pump
and rubber impeller sea water pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 217 kg [478 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier 2
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm3; 1 kW = 1.3596 mhp = 1.3410 HP* Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
4JH4-HTE with KMH4A marine gear
www.yanmarmarine.com
4JH4-HTE Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 80.9 kW ( 110 mhp) / 3200 rpm
Cooling system Fresh water cooling by centrifugal water pump and rubber impeller sea water pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 217 kg (478 lbs)
Environmental EU RCD, US EPA Tier2, BSO II & EMC
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665)Technical data is according to ISO 8665 / 3046
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com or contact your supplier)
470 mm (18.5 in)
235 mm (9.3 in) 235 mm (9.3 in)
30 m
m (1
.2 in
)
MAX.
110
mm (4
.3 in
)MI
N.10
0 mm
(3.9
in)
201.
5 mm
(7.9
in)
457.
6 mm
(18
in)65
9.1
mm (2
5.9
in)
288.6 mm (11.3 in) (BELT COVER)327.5 mm (12.9 in)(OPTIONAL ALTERNATOR)333.1 mm (13.1 in)
616.1 mm (24.2 in)(OPTIONAL)660.6 mm (26 in)
FUEL INLET
206.8 mm (8.1 in)
39.5 mm (1.6 in)
506 mm (20 in) 188.6 mm (7.4 in)901.4 mm (35.5 in)
256 mm (10.1 in)
8º11
4.9
mm
(4.5
in)
118.
4 m
m(4
.7 in
)
933 mm (36.7 in)
234.
6 m
m (9
.2 in
)18
3.6
mm
(7.2
in)
137 mm (5.4 in) 60 mm(2.4 in)
WATER INLET
Right side viewRear viewE
N_D
S4
JH4
-HT
E_0
813
www.yanmar.eu
4JH4-HTE with KMH4A marine gear
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
www.yanmarmarine.com
Version: 2011-01
Yanmar Europe BV
Marine Gears/Drive
Performance Curves (Output is according ISO 8665)
Power Torque Fuel Consumption
Instrument Panels
Type of instrument panel
Function Digital B-type Panel Digital C-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O O1-2 Push button switch for engine stop O O1-3 Moisture cap for key switch O O2 Alarm lamp unit
2-1 Battery low charge alarm O O2-2 Coolant high temperature alarm O O2-3 Lubricating oil low pressure O O2-5 Water in fuel filter alarm (optional) X O3 Meters
3-1 Lubricating oil pressure meter X O3-2 Coolant temperature meter X O3-3 Hour meter O O3-4 Tachometer O O4 Audible alarm buzzer O O
Note: O = Equipped on panel X = Not equipped on panel
Standard Package• Set of flexible mounts• Exhaust mixing elbow (L-type)• V-belt safety cover• Expansion tank for fresh water cooling system• Alternator 12 V - 80 A• Electric stop solenoid
Optional• Digital B or C type instrument panel• Second Alternator 12V130A or 24V75A• Exhaust mixing elbow (U-type))• Various extension wire harnesses (4M, 6M, 10M)• Hotwaterkit with cocks
Optional• Second alternator 12V - 130A or 24V - 75A, including smart regulator• High-riser mixing elbow [insted of L-elbow]• Extension wire harnesses [4m, 6m 10m]• Hot water kit with cocks • Second station harness• C30-panel• Sensor for C-30 panel
Standard Package• Set of flexible mounts• Exhaust mixing elbow [L-type]• V-belt safety cover• Expansion tank for fresh water cooling system• Alternator 12V - 125A• Electric stop solenoid • Operation manual• B20-panel• Sensor for instrument panel
ACCESSORIES
EN
_DS
4JH
4-H
TE
_081
3
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
Maximum output at crankshaft * 55.2 kW@3200 rpm [75 mhp@3200 rpm]
Displacement 1.995 ltr [121.7 cu in]
Bore x stroke 84 mm x 90 mm [3.31 in x 3.54 in]
Cylinders 4, 4-valves per cylinder
Combustion system Direct injection
Aspiration Turbocharged
Starting system Electric starting 12V - 1.4 kW
Alternator 12V - 125A
Cooling system Fresh water cooling by centrifugal water pump
and rubber impeller sea water pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 207 kg [456 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier 3
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm3; 1 kW = 1.3596 mhp = 1.3410 HP* Fuel temperature 40° C at the inlet of the fuel injection pump [ISO 8665]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
4JH4-TE with KM4A2 marine gear
www.yanmarmarine.com
4JH4-TE Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 55,2 kW ( 75 mhp) / 3200 rpm
Cooling system Fresh water cooling by centrifugal water pump and rubber impeller sea water pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 207 kg (456 lbs)
Environmental EU RCD, BSO II, EPA TIER 3, EMC
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665)Technical data is according to ISO 8665 / 3046
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
201.
5 m
m (7
.9 in
)
OPTIONAL ALTERNATOR 333.1 mm (13.1 in) incl. BELT COVER 327.5 mm (12.9 in)
470 mm (18.5 in)
235 mm (9.3 in) 235 mm (9.3 in)
457.
6 m
m (1
8 in
)
659.
1 m
m (2
5.9
in)
288.6 mm (11.3 in)
OPTIONAL660.6 mm (26 in)
616.1 mm (24.2 in)
FUEL INLET
MAX
.110
mm
(4.3
in)
MIN
. 100
mm
(3.9
in)
30 m
m(1
.2 in
)
208.5 mm (8.2 in)
39.5 mm (1.6 in)
506 mm 19.9 in) 188.6 mm (7.4 in)
271 mm (10.6 in)
35.4
mm
(1.4
in)
903.1 mm (35.6 in)
7º
7
Ø 33.5 mm
(1.3 in)
234.
6 m
m (9
.2 in
)
137 mm (5.4 in)
60.1 mm (2.4 in)
183.
6 m
m (7
.2 in
)
Right side viewRear viewE
N_D
S4
JH4
-TE
_071
3
www.yanmar.eu
4JH4-TE with KM4A2 marine gear
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
www.yanmarmarine.com
Version: 2011-07
Yanmar Europe BV
Marine Gears/Drive
Performance Curves (Output is according ISO 8665)
Maximum output at crankshaft
Power Torque
Propeller power curve 2.5
Fuel Consumption
Instrument Panels
Type of instrument panel
Function Digital B-type Panel Digital C-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O O1-2 Push button switch for engine stop O O1-3 Moisture cap for key switch O O2 Alarm lamp unit
2-1 Battery low charge alarm O O2-2 Coolant high temperature alarm O O2-3 Lubricating oil low pressure O O2-4 Water in sail drive seal alarm O O2-5 Water in fuel filter alarm X O2-6 Sea water insufficient flow alarm X O3 Meters
3-1 Lubricating oil pressure meter X O3-2 Coolant temperature meter X O3-3 Hour meter O O3-4 Tachometer O O4 Audible alarm buzzer O O
Note: O = Equipped on panel X = Not equipped on panel
Standard Package• Set of flexible mounts• Exhaust mixing elbow (L-type)• V-belt safety cover• Expansion tank for fresh water cooling system• Alternator 12 V - 80 A• Electric stop solenoid
Optional• Digital B or C type instrument panel• Second Alternator 12V130A or 24V75A• Exhaust mixing elbow (U-type)• Various extension wire harnesses (4M, 6M, 10M)• Hotwaterkit with cocks
Direction of rotation Clockwise viewed Clockwise or counterclockwise Clockwise or counterclockwise Clockwise & counter clockwise Clockwise & counter clockwise
(propeller shaft - fwd) from flywheel side viewed from flywheel side viewed from flywheel side viewed from flywheel side viewed from flywheel side
Dry weight engine 235 kg (518 lbs) 237 kg (522 lbs) 238 kg (524 lbs) 237 kg (522 lbs) 249 kg (549 lbs)
and gear/drive
Length engine 923 mm (36.3 in) 903 mm (35.6 in) 933 mm (36.7 in) 1017 mm (40 in) 782 mm (30.8 in)
Optional• Digital B or C type instrument panel• Second Alternator 12V - 130A or 24V - 75A, including smart regulator• High-riser mixing elbow [instead of L-elbow]• Extension wire harness [4m, 6m, 10m]• Hot water kit with cocks • Second station harness• C30-panel• Sensor for C30-panel• Extension saildrive leg [75mm]• Propeller cone nut kit SD60
Standard Package• Set of flexible mounts• Exhaust mixing elbow [L-type]• V-belt safety cover• Expansion tank for fresh water cooling system• Alternator 12V - 125A• Electric stop solenoid • Operation manual• B20-panel• Sensor for instrument panel
ACCESSORIES
EN
_DS
4JH
4-T
E_0
713
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
Maximum output at crankshaft * 39.6 kW@3000 rpm [53.1 mhp@3000 rpm]
Displacement 2.19 ltr [134 cu in]
Bore x stroke 88 mm x 90 mm [3.46 in x 3.54 in]
Cylinders 4 in line
Combustion system Direct injection
Aspiration Natural aspiration
Starting system Electric starting 12V - 1.4 kW
Alternator 12V - 125A
Cooling system Fresh water cooling by centrifugal water pump
and rubber impeller sea water pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 201 kg [443 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier 3
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm3: 1 kW = 1.3596 mhp = 1.3410 HP* Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
4JH5E with KM35P marine gear
www.yanmarmarine.com
4JH5E Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 39.6 kW (53,1 mhp) / 3000 rpm
Standard Features• Set of flexible engine mounts• Exhaust mixing elbow (L-type)• V-belt safety cover• Fresh water expansion tank• Alternator 12 V - 80 A• Electric stop solenoid• Operation manual
Optional• Digital B panel keyless• Digital C panel with key switch or key less• Second Alternator 12V80A, 12V130A or 24V75A • High riser mixing Elbow (Instead of L-Elbow)• 4M, 6M, 10M Extension Wire harness• Hot water kit with cocks• Second station harness
Accessories
Digital B-panel and C-panel with keyswitch Digital B-panel and C-panel keyless
Keyswitch Sealed rocker switch for engine on/start
Stop Button Sealed rocker switch for glow function
Extra for all C-panels: Coolant temperature gauge, Lubricating oil pressure gauge
DigitalB-panelkeyless
DigitalC-panelkeyswitch
PERFORMANCE CURVES
Optional• Second alternator 12V - 130A or 24V - 75A, including smart regulator• High-riser mixing elbow [instead of L-elbow]• Extension wire harness [4m, 6m, 10m]• Hot water kit with cocks• Second station harness • C30-panel• Sensor for C30-panel• Extension saildrive leg [75 mm] • Propeller cone nut kit SD60
Standard Package• Set of flexible engine mounts• Exhaust mixing elbow [L-type]• V-belt safety cover• Fresh water expansion tank• Alternator 12V - 125A• Electric stop solenoid• Operation manual • B20-panel• Sensor for instrument panel
ACCESSORIES
EN
_DS
4JH
5E_0
813
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
Maximum output at crankshaft * 147 kW@3300 rpm [200 mhp@3300 rpm]
** 140 kW@3300 rpm [190 mhp@3300 rpm]
Displacement 3.455 ltr [211 cu in]
Bore x stroke 100 mm x 110 mm [3.94 in x 4.33 in]
Cylinders 4 in line
Combustion system Direct injection
Aspiration Turbocharged with intercooler
Starting system Electrical starting 12V
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump
and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 365 kg [805 lbs]
Environmental EU: RCD BSO II EMC
SOLAS MED 96/98/EC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.842 g/cm3; 1 mhp = 1 ps = 0.7355 kW = 0.9863 bhp* Fuel temperature 25°C at the inlet of the fuel injection pump [ISO 3046-1]** Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006] Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
4LHA-DTP with ZF63A marine gear
www.yanmarmarine.com
4LHA-DTP Series
Rear view
222.5 mm(8.8 in)641 mm (25.2 in)
153 mm(6.0 in)
Mixing elbowo 102 mm (4 in)
1059.2 mm (41.7 in)
Right side view719.1 mm (28.3 in)
368.6 mm (14.5 in) 350.5 mm (13.8 in)
574 mm (22.6 in)
789
mm
(31.
1 in
)
238
mm
(9.4
in)
max
. 12
0 m
m (4
.7 in
)m
in.
111
mm
(4.4
in)
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 147 kW (200 mhp) / 3300 rpm** 140 kW (190 mhp) / 3300 rpm
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller seawater pump
Lubrication system Enclosed,forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 365 kg (805 lbs)
Environmental EU RCD, BSO II, EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.842g/cm3; 1 mhp = 1PS = 0.7355 kW = 0.9863 bhp * Fuel temperature 25°C at the inlet of the fuel injection pump (ISO 3046-1) **Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665 : 2006)
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
EN
_DS
4LH
A-D
TP_
041
3
www.yanmar.eu
4LHA-DTP with ZF63A marine gear
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
www.yanmarmarine.com
Version: 2011-09
Yanmar Europe BV
Instrument Panels
Note: O = Equipped on panel X = Not equipped on panel
Standard Package• Sensor for various panels• Exhaust/water mixing elbow (L-type)• Alternator 12 V - 80 A
Optional• Flexible mounts• Exhaust/water mixing elbow, U-type (high riser)• New C-type instrument panel• Dual station Y harness• Dipstick for opposite side• Air venting device for cooling water tank
Accessories
Performance Curves (Output is according ISO 8665 - Output includes +/- 3% tolerance)
Direction of rotation Clockwise & counter clockwise Clockwise & counter clockwise(propeller shaft - fwd) viewed from flywheel side viewed from flywheel side
Dry weight engine and gear/drive 409 kg (902 lbs) 393 kg (866 lbs)
*** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
www.yanmarmarine.com
Version: 2011-09
Yanmar Europe BV
Instrument Panels
Note: O = Equipped on panel X = Not equipped on panel
Standard Package• Sensor for various panels• Exhaust/water mixing elbow (L-type)• Alternator 12 V - 80 A
Optional• Flexible mounts• Exhaust/water mixing elbow, U-type (high riser)• New C-type instrument panel• Dual station Y harness• Dipstick for opposite side• Air venting device for cooling water tank
Accessories
Performance Curves (Output is according ISO 8665 - Output includes +/- 3% tolerance)
Direction of rotation Clockwise & counter clockwise Clockwise & counter clockwise(propeller shaft - fwd) viewed from flywheel side viewed from flywheel side
Dry weight engine and gear/drive 409 kg (902 lbs) 393 kg (866 lbs)
*** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
PERFORMANCE CURVES (Output is according ISO 8665 - Output includes +/- 3% tolerance)
MARINE GEARS*
INSTRUMENT PANELS
Optional• Flexible mounts• High-riser/water mixing elbow [instead of L-elbow]• New C-type instrument panel• Dual station Y harness• Dipstick for opposite side• Air venting device for cooling water tank
Standard Package• Sensor for various panels• Exhaust/water mixing elbow [L-type]• Alternator 12V - 80A
ACCESSORIES
EN
_DS
4LH
A-D
TP_
041
3
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
TyPe Of inSTrumenT PAneL
new C-TyPe PAneL
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
function
1-Switch unit
1-1 Key switch for GLOW/OFF/ON/START [4-position switch]
1-2 Engine stop switch
1-3 Alarm buzzer [C.W. Temp., L.O. Pressure]
1-4 Alarm buzzer stop switch
1-5 Illumination switch for meters
2-Alarm lamp unit
Battery not charging
C.W. high temperature
L.O. low pressure
Boost pressure high [for 4LHA-STP]
3-Tachometer with hour meter
4-Sub meter unit
4-1 L.O. pressure meter
4-2 C.W. Temperature meter
4-3 Boost meter [turbo]
5-Quartz clock
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Not equipped on panel
Not equipped on panel
* Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Maximum output at crankshaft * 118 kW@3300 rpm [160 mhp@3300 rpm]
** 113 kW@3300 rpm [154 mhp@3300 rpm]
Displacement 3.455 ltr [211 cu in]
Bore x stroke 100 mm x 110 mm [3.94 in x 4.33 in]
Cylinders 4 in line
Combustion system Direct injection
Aspiration Turbocharged with intercooler
Starting system Electrical starting 12V
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump
and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 360 kg [794 lbs]
Environmental EU: RCD BSO II EMC
SOLAS MED 96/98/EC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.842 g/cm3; 1 mhp = 1 ps = 0.7355 kW = 0.9863 bhp* Fuel temperature 25°C at the inlet of the fuel injection pump [ISO 3046-1]** Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006] Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
4LHA-HTP with ZF45A marine gear
www.yanmarmarine.com
4LHA-HTP Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 118 kW (160 mhp) / 3300 rpm** 113 kW (154 mhp) / 3300 rpm
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 360 kg (794 lbs)
Environmental EU RCD, BSO II, EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.842g/cm3; 1 mhp = 1PS = 0.7355 kW = 0.9863 bhp * Fuel temperature 25°C at the inlet of the fuel injection pump (ISO 3046-1) **Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665 : 2006)
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
Rear view
222.5 mm(8.8 in)209 mm (8.2 in)157.7 mm
(6.2 in)
Mixing elbowo 102 mm (4 in)
1021.9 mm (40.2 in)
719.1 mm (28.3 in)
368.6 mm (14.5 in) 350.5 mm (13.8 in)
574 mm (22.6 in)
811
mm
(31.
9 in
)
238
mm
(9.4
in)
max
. 12
0 m
m (4
.7 in
)m
in.
111
mm
(4.4
in)
Right side view
EN
_DS
4LH
A-H
TP_
041
3
www.yanmar.eu
4LHA-HTP with ZF45A marine gear
MARINE DIESEL ENGINES
Optional• Flexible mounts• High-riser/water mixing elbow [instead of L-elbow]• New C-type instrument panels• Dual station Y harness• Dipstick for opposite side• Air venting device for cooling water tank
Standard Package• Sensor for various panels• Exhaust/water mixing elbow [L-type]• Cooling water hoses• Alternator 12V - 80A
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Battery not charging OC.W. high temperature OL.O. low pressure OBoost pressure high (for 4LHA-STP O
3 Tachometer with hour meter O4 Sub meter unit O
4-1 L.O. pressure meter O
4-2 C.W. Temperature meter O4-3 Boost meter (turbo) X
5 Quartz clock X
Note: O = Equipped on panel X = Not equipped on panel
Standard Package• Sensor for various panels• Exhaust/water mixing elbow (L-type)• Cooling water hoses• Alternator 12 V - 80 A
Optional• Flexible mounts• Exhaust/water mixing elbow, U-type (high riser)• New C-type instrument panels• Dual station Y harness• Dipstick for opposite side• Air venting device for cooling water tank
Accessories
Performance Curves (Output is according ISO 8665 - Output includes +/- 3% tolerance)
Direction of rotation Clockwise & counter clockwise Clockwise & counter clockwise(propeller shaft - fwd) viewed from flywheel side viewed from flywheel side
Dry weight engine and gear/drive 404 kg (891 lbs) 388 kg (855 lbs)
*** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Battery not charging OC.W. high temperature OL.O. low pressure OBoost pressure high (for 4LHA-STP O
3 Tachometer with hour meter O4 Sub meter unit O
4-1 L.O. pressure meter O
4-2 C.W. Temperature meter O4-3 Boost meter (turbo) X
5 Quartz clock X
Note: O = Equipped on panel X = Not equipped on panel
Standard Package• Sensor for various panels• Exhaust/water mixing elbow (L-type)• Cooling water hoses• Alternator 12 V - 80 A
Optional• Flexible mounts• Exhaust/water mixing elbow, U-type (high riser)• New C-type instrument panels• Dual station Y harness• Dipstick for opposite side• Air venting device for cooling water tank
Accessories
Performance Curves (Output is according ISO 8665 - Output includes +/- 3% tolerance)
Direction of rotation Clockwise & counter clockwise Clockwise & counter clockwise(propeller shaft - fwd) viewed from flywheel side viewed from flywheel side
Dry weight engine and gear/drive 404 kg (891 lbs) 388 kg (855 lbs)
*** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
PERFORMANCE CURVES (Output is according ISO 8665 - Output includes +/- 3% tolerance
INSTRUMENT PANELS
ACCESSORIES
EN
_DS
4LH
A-H
TP_
041
3
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
MARINE GEARS*
New C-TyPe PANeL
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Function
1-Switch unit
1-1 Key switch for GLOW/OFF/ON/START [4-position switch]
1-2 Push button switch for engine stop
1-3 Moisture cap for key switch
1-4 Alarm buzzer stop switch
1-5 Illumination switch for meters
2-Alarm lamp unit
Battery not charging
C.W. high temperature
L.O. low pressure
Boost pressure high [for 4LHA-STP]
3-Tachometer with hour meter
4-Sub meter unit
4-1 L.O. pressure meter
4-2 C.W. Temperature meter
4-3 Boost meter [turbo]
5-Quartz clock
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Not equipped on panel
Not equipped on panel
TyPe OF iNSTrumeNT PANeL
* Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Maximum output at crankshaft * 177 kW@3300 rpm [240 mhp@3300 rpm]
** 169 kW@3300 rpm [230 mhp@3300 rpm]
Displacement 3.455 ltr [211 cu in]
Bore x stroke 100 mm x 110 mm [3.94 in x 4.33 in]
Cylinders 4 in line
Combustion system Direct injection
Aspiration Turbocharged with intercooler
Starting system Electrical starting 12V
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump
and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 365 kg [805 lbs]
Environmental EU: RCD BSO II EMC
SOLAS MED 96/98/EC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.842 g/cm3; 1 mhp = 1 ps = 0.7355 kW = 0.9863 bhp* Fuel temperature 25°C at the inlet of the fuel injection pump [ISO 3046-1]** Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
4LHA-STP with ZF63A marine gear
www.yanmarmarine.com
4LHA-STP Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 177 kW (240 mhp) / 3300 rpm** 169 kW (230 mhp) / 3300 rpm
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 365 kg (805 lbs)
Environmental EU RCD, BSO II, EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.842g/cm3; 1 mhp = 1PS = 0.7355 kW = 0.9863 bhp * Fuel temperature 25°C at the inlet of the fuel injection pump (ISO 3046-1) **Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665 : 2006)
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
Rear view
222.5 mm(8.8 in)641 mm (25.2 in)
153 mm(6.0 in)
Mixing elbowo 102 mm (4 in)
1059.2 mm (41.7 in)
Right side view719.1 mm (28.3 in)
368.6 mm (14.5 in) 350.5 mm (13.8 in)
574 mm (22.6 in)
789
mm
(31.
1 in
)
238
mm
(9.4
in)
max
. 12
0 m
m (4
.7 in
)m
in.
111
mm
(4.4
in)
EN
_DS
4LH
A-S
TP_
041
3
www.yanmar.eu
4LHA-STP with ZF63A marine gear
MARINE DIESEL ENGINES
Optional• Flexible mounts• High-riser/water mixing elbow [instead of L-elbow]• New C-type instrument panel• Dual station Y harness• Dipstick for opposite side• Air venting device for cooling water tank
Standard Package• Sensor for various panels• Exhaust/water mixing elbow [L-type]• Alternator 12V - 80A
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
www.yanmarmarine.com
Version: 2011-09
Yanmar Europe BV
Instrument Panels
Performance Curves (Output is according ISO 8665 - Output includes +/- 3% tolerance)
Direction of rotation Clockwise & counter clockwise Clockwise & counter clockwise(propeller shaft - fwd) viewed from flywheel side viewed from flywheel side
Dry weight engine and gear/drive 409 kg (902 lbs) 393 kg (866 lbs)
*** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
4-1 4-2 3 1-4
1-4
2
400
76
90
New C-type Panel1-5
1-21-3
180
160
190 190
1-1 12.711
180
Note: O = Equipped on panel X = Not equipped on panel
Battery not charging OC.W. high temperature OL.O. low pressure OBoost pressure high (for 4LHA-STP) O
3 Tachometer with hour meter O4 Sub meter unit O
4-1 L.O. pressure meter O
4-2 C.W. Temperature meter O4-3 Boost meter (turbo) X
5 Quartz clock X
Standard Package• Sensor for various panels• Exhaust/water mixing elbow (L-type)• Alternator 12 V - 80 A
Optional• Flexible mounts• Exhaust/water mixing elbow, U-type (high riser)• New C-type instrument panel• Dual station Y harness• Dipstick for opposite side• Air venting device for cooling water tank
Accessories
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
www.yanmarmarine.com
Version: 2011-09
Yanmar Europe BV
Instrument Panels
Performance Curves (Output is according ISO 8665 - Output includes +/- 3% tolerance)
Direction of rotation Clockwise & counter clockwise Clockwise & counter clockwise(propeller shaft - fwd) viewed from flywheel side viewed from flywheel side
Dry weight engine and gear/drive 409 kg (902 lbs) 393 kg (866 lbs)
*** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
4-1 4-2 3 1-4
1-4
2
400
76
90New C-type Panel
1-5
1-21-3
180
160
190 190
1-1 12.711
180
Note: O = Equipped on panel X = Not equipped on panel
Battery not charging OC.W. high temperature OL.O. low pressure OBoost pressure high (for 4LHA-STP) O
3 Tachometer with hour meter O4 Sub meter unit O
4-1 L.O. pressure meter O
4-2 C.W. Temperature meter O4-3 Boost meter (turbo) X
5 Quartz clock X
Standard Package• Sensor for various panels• Exhaust/water mixing elbow (L-type)• Alternator 12 V - 80 A
Optional• Flexible mounts• Exhaust/water mixing elbow, U-type (high riser)• New C-type instrument panel• Dual station Y harness• Dipstick for opposite side• Air venting device for cooling water tank
Accessories
PERFORMANCE CURVES (Output is according ISO 8665 - Output includes +/- 3% tolerance)
INSTRUMENT PANELS
ACCESSORIES
EN
_DS
4LH
A-S
TP_
041
3
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
MARINE GEARS*
digiTAL C-TyPe PAneL
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Function
1-Switch unit
1-1 Key switch for GLOW/OFF/ON/START [4-position switch]
1-2 Engine stop switch
1-3 Alarm buzzer [C.W. Temp., L.O. Pressure]
1-4 Alarm buzzer stop switch
1-5 Illumination switch for meters
2-Alarm lamp unit
Battery not charging
C.W. high temperature
L.O. low pressure
Boost pressure high [for 4LHA-STP]
3-Tachometer with hour meter
4-Sub meter unit
4-1 L.O. pressure meter
4-2 C.W. Temperature meter
4-3 Boost meter [turbo]
5-Quartz clock
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panel
Not equipped on panel
Not equipped on panel
TyPe OF inSTrumenT PAneL
* Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Maximum output at crankshaft 162 kW@4000 rpm [220 mhp@4000 rpm]
191 kW@4000 rpm [260 mhp@4000 rpm]
Displacement 2.993 ltr [183 cu in]
Bore x stroke 84 mm x 90 mm [3.31 in x 3.54 in]
Cylinders 6 in line
Combustion system Direct injection with Bosch Common-rail system
Aspiration Turbocharger + charge-air cooler
Low Idle rpm 650 - 950 rpm [adjustable]
Electric system 12V
Alternator 12V - 150A
Start-assist Glow-plug system
Cooling system Fresh water cooling by centrifugal fresh water pump
Sea water cooling by rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counter clockwise viewed from fl ywheel side
Dry weight without gear 328 kg [723 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier3
IMO: MARPOL 73/78 Annex VI
SOLAS MED 96/98/EC
Engine mounting Rubber type fl exible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
6BY3-260 with KMH51A Marine gear
DIMENSIONS
Type 6BY3-2206BY3-260
Configuration 6-cylinder in line, 4-stroke, water cooled diesel engine
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665:2006)
Dimensions
6BY3-260 with KMH51A Marine gear
www.yanmarmarine.com
FRONT VIEW RIGHT SIDE VIEW
Version 2012-10
EN
_DS
6B
Y3
_041
3
www.yanmar.eu
MARINE DIESEL ENGINES
Optional accesories• High-riser mixing elbow [instead of L-elbow]• Exhaust-side 2nd dipstick• Electric gearshift• Trolling on gearbox [mechanical and electrical]• NMEA2000 digital display• Full NMEA2000 electronic control system [CAN-bus]
Standard engine package• Single pole, 150A Alternator• Exhaust mixing elbow [L-type]• Automatic glow-plug controller• Flexible engine mounting• Analogue throttle with redundancy function
Type 6BY3-2206BY3-260
Performance Curves
Drive systems
ModelTypeDry WeightReduction Ratio 1,67/1,67 2,13/2,13 2,43/2,43Direction of rotationLub oil specificationsDry weight - engine & gear
ModelTypeDry WeightReduction Ratio 1,22/1,22 1,58/1,58 2,08/2,08 2,47/2,47Direction of rotationLub oil specificationsDry weight - engine & gear
Control system "Classic"
Engine Accesories
Standard engine package Single pole, 150A AlternatorL-type exhaust elbowAutomatic glow-plug controllerFlexible engine mountingAnalogue throttle with redundancy function
Optional accesories High-riser mixing elbowExhaust-side 2nd dipstickElectric gearshiftTrolling on gearbox [mechanical and Electrical]NMEA2000 Digital displayFull NMEA2000 electronic control system [CAN-bus]
www.yanmarmarine.com
395 kg
Hydraulic Actuated Multi-friction disc clutch59 kg excl. foot and cooler [=20 kg]
Clockwise / Counterclockwise viewed from the sternAPI class: CF or higher SAE grade #30
Clockwise / Counterclockwise viewed from the stern
KMH50V [Integral V-drive 12°]
0
20
40
60
80
100
120
140
160
180
200
1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500
Pow
er [k
W]
Crankshaft speed [RPM]
6BY3-260
6BY3-220
0
100
200
300
400
500
600
1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500
Torq
ue [N
m]
Crankshaft speed [RPM]
6BY3-220
6BY3-260
Version 2012-10
Type 6BY3-2206BY3-260
Performance Curves
Drive systems
ModelTypeDry WeightReduction Ratio 1,67/1,67 2,13/2,13 2,43/2,43Direction of rotationLub oil specificationsDry weight - engine & gear
ModelTypeDry WeightReduction Ratio 1,22/1,22 1,58/1,58 2,08/2,08 2,47/2,47Direction of rotationLub oil specificationsDry weight - engine & gear
Control system "Classic"
Engine Accesories
Standard engine package Single pole, 150A AlternatorL-type exhaust elbowAutomatic glow-plug controllerFlexible engine mountingAnalogue throttle with redundancy function
Optional accesories High-riser mixing elbowExhaust-side 2nd dipstickElectric gearshiftTrolling on gearbox [mechanical and Electrical]NMEA2000 Digital displayFull NMEA2000 electronic control system [CAN-bus]
www.yanmarmarine.com
395 kg
Hydraulic Actuated Multi-friction disc clutch59 kg excl. foot and cooler [=20 kg]
Clockwise / Counterclockwise viewed from the sternAPI class: CF or higher SAE grade #30
Maximum output at crankshaft 162 kW@4000 rpm [220 mhp@4000 rpm]
191 kW@4000 rpm [260 mhp@4000 rpm]
Displacement 2.993 ltr [183 cu in]
Bore x stroke 84 mm x 90 mm [3.31 in x 3.54 in]
Cylinders 6 in line
Combustion system Direct injection with Bosch Common Rail System
Aspiration Turbocharger + charge air cooler
Low Idle rpm 650 - 950 rpm [adjustable]
Electric system 12V
Alternator 12V - 150A
Start-assist Glow-plug system
Cooling system Fresh water cooling by centrifugal fresh water pump
Sea water cooling by rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from fl ywheel side
Dry weight without gear 328 kg [723 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier3
IMO: MARPOL 73/78 Annex VI
Engine mounting Rubber type fl exible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
Type 6BY3-220Z6BY3-260Z
Configuration 6-cylinder in line, 4-stroke, water cooled diesel engine
ModelTypeDry WeightReduction Ratio 1,36 1,5 1,65Propeller speed 2941 2667 2424Direction of rotationLub oil specificationsDry weight - engine & gear1 - Inner and outer transom surface must be parallel within 3mm in area covered by transom plates and remain within transom thickness limits.
2 - Area covered by gimbal housing assembly must be flat to within 1.6mm.
3 - Area covered by inner transom plate must be flat to within 3.2mm
4 - Transom angle: 13° to 16°
5 - Also available with Bravo X-2 drive's, please contact your local supplier for support.
Control system "Classic"
Engine Accesories
Standard engine package Single pole, 150A AlternatorHigh Riser mixing exhaust elbowAutomatic glow-plug controllerFlexible engine mountingAnalogue throttle with redundancy function
Optional accesories Through transom exhaustExhaust-side 2nd dipstickElectric gearshiftNMEA2000 Digital displayVarious monitoring gaugesFull NMEA2000 electronic control system [CAN-bus]
Propellers Propeller size 20" - 22" - 24" - 26" - 28"Propellers with cup 24"- 26"
www.yanmarmarine.com
Mercury High Performance Gearlube430 kg
API class: GL5 SAE grade #80W90 or QuickSilver High Performance Gearlube445 kg
Mercruiser Bravo 1 Steerable Z-drive with single propellerMechanical cone-clutch type Sterndrive
59 kg [drive] / 48 kg [Transom + trim-pump] / 8 kg [Propeller]
Clockwise / Counterclockwise viewed from the stern
ModelTypeDry WeightReduction Ratio 1,36 1,5 1,65Propeller speed 2941 2667 2424Direction of rotationLub oil specificationsDry weight - engine & gear1 - Inner and outer transom surface must be parallel within 3mm in area covered by transom plates and remain within transom thickness limits.
2 - Area covered by gimbal housing assembly must be flat to within 1.6mm.
3 - Area covered by inner transom plate must be flat to within 3.2mm
4 - Transom angle: 13° to 16°
5 - Also available with Bravo X-2 drive's, please contact your local supplier for support.
Control system "Classic"
Engine Accesories
Standard engine package Single pole, 150A AlternatorHigh Riser mixing exhaust elbowAutomatic glow-plug controllerFlexible engine mountingAnalogue throttle with redundancy function
Optional accesories Through transom exhaustExhaust-side 2nd dipstickElectric gearshiftNMEA2000 Digital displayVarious monitoring gaugesFull NMEA2000 electronic control system [CAN-bus]
Propellers Propeller size 20" - 22" - 24" - 26" - 28"Propellers with cup 24"- 26"
www.yanmarmarine.com
Mercury High Performance Gearlube430 kg
API class: GL5 SAE grade #80W90 or QuickSilver High Performance Gearlube445 kg
Mercruiser Bravo 1 Steerable Z-drive with single propellerMechanical cone-clutch type Sterndrive
59 kg [drive] / 48 kg [Transom + trim-pump] / 8 kg [Propeller]
Clockwise / Counterclockwise viewed from the stern
ZT370 Steerable Z-drive with duo-propellerHydraulic Actuated Multi-friction disc Sterndrive
69 kg [drive] / 46 kg [Transom + trim-pump] / 15 kg [Propellers]
0
20
40
60
80
100
120
140
160
180
200
1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500
Pow
er [k
W]
Crankshaft speed [RPM]
6BY3-260
6BY3-220
0
100
200
300
400
500
600
1.000 1.500 2.000 2.500 3.000 3.500 4.000 4.500
Torq
ue [N
m]
Crankshaft speed [RPM]
6BY3-220
6BY3-260
Version 2012-10
PERFORMANCE CURVES
CONTROL SYSTEM “CLASSIC”
Optional accesories• Through transom exhaust• Exhaust-side 2nd dipstick• Electric gearshift• NMEA2000 digital display• Various monitoring gauges• Full NMEA2000 electronic control system [CAN-bus]
Propellers• Propeller size
20” - 22” - 24” - 26” - 28”• Propellers with cup
24”- 26”
Standard engine package• Single pole, 150A alternator• High-riser mixing exhaust elbow• Automatic glow-plug controller• Flexible engine mounting• Analogue throttle with redundancy function
ENGINE ACCESORIES
EN
_DS
6B
Y3Z
_081
3
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
1 - Inner and outer transom surface must be parallel within 3 mm in area covered by transom plates and remain within transom thickness limits.2 - Area covered by gimbal housing assembly must be fl at to within 1.6 mm.3 - Area covered by inner transom plate must be fl at to within 3.2 mm.4 - Transom angle: 13° to 16°.5 - Also available with Bravo X-2 drive’s, please contact your local supplier for support.
DRIVE SYSTEMS
2.18
Mercruiser Bravo 1 Steerable Z-drive with single propeller
Mechanical cone-clutch type Sterndrive
59 kg [drive]/48 kg [Transom + trim-pump]/8 kg [Propeller]
1.36
2424
Clockwise & Counterclockwise viewed from the stern
Mercury High Performance Gearlube
430 kg
Model
Type
Dry weight
Reduction ratio [fwd/asn]
Propeller speed [fwd/asn]
Direction of rotation
Lub oil specifi cations
Dry weight - engine & gear
1.5 1.65
2667 2424
1835
393.
3 m
m (1
5.5
in)
206.5 mm (8.1 in)966.6 mm (38 in) 373.4 mm (14.7 in)429.5 mm (16.9 in)
1769.5 mm (69.5 in)
149
mm
(5.9
in)
7°
502.2 mm (19.7 in)
933.
5 m
m (3
6.7
in)31
9.5
mm
(12.
6 in)
614
mm
(24.
1 in)
673 mm (26.4 in)
384.3 mm (15.1 in)886.4 mm (34.8 in)
56.2
mm
(2.2
in)
MARINE DIESEL ENGINES
6CX-530 Series
DIMENSIoNS [uNIt: MM]
EN
_DS
6CX
-53
0_0
813
www.yanmar.eu
Front view with gearbox KMH70A Right side view with gearbox KMH70A
Configuration
Maximum output at crankshaft
Continuous rating output at crankshaft
Displacement
Bore x stroke
Cylinders
Combustion system
Aspiration
Starting system
Alternator
Cooling system
Lubrication system
Direction of rotation [crankshaft]
Dry weight without gear
Environmental
Engine mounting
4-stroke, vertical, water cooled diesel engine
* 390 kW@2900 rpm [530 mhp@2900 rpm]
355 kW@2809 rpm [482 mhp@2809 rpm]
7.413 ltr [452 cu in]
110 mm x 130 mm [4.33 in x 5.12 in]
6 in-line
Direct injection
Dry turbocharger with water-cooled jacket, charge-air cooler
Electric starting 12V [24V = optional]
12V - 120A [24V - 60A = optional]
Fresh water cooling by centrifugal fresh water pump
and rubber impeller seawater pump
Enclosed, forced lubricating system
Counter clockwise viewed from flywheel side
837 kg [1845 lb]
Eu: RCD
uS: EPA tier2 EMC
Rubber type flexible mounting
NotE: Fuel condition: Density at 15°C = 0.84 g/cm3
* Fuel temperature 40°C at the inlet of the fuel injection pump [ISo 8665: 2006]
MARINE DIESEL ENGINES
PERFoRMANCE CuRVES
EN
_DS
6CX
-53
0_0
813
www.yanmar.eu
NotE: All data subject to change without notice. text and illustrations are not binding.
Maximum output at crankshaft * 232 kW@3800 rpm [315 mhp@3800 rpm]
** 225 kW@3800 rpm [306 mhp@3800 rpm]
Displacement 4.164 ltr [254 cu in]
Bore x stroke 94 mm x 100 mm [3.7 in x 3.94 in]
Cylinders 6 in line, 4-valves per cylinder
Combustion system Direct injection
Aspiration Turbocharged with intercooler
Starting system Electric starting 12V - 2.5 kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and
rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 408 kg [899 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier2
IMO: MARPOL 73/78 Annex VI
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³; 1 kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 25°C at the inlet of the fuel injection pump [ISO 3046-1]** Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
6LPA-STP2 / KMH50A marine gear
www.yanmarmarine.com
6LPA-STP2 Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 232 kW (315 mhp) / 3800 rpm** 225 kW (306 mhp) / 3800 rpm
Cylinders 6 in line cylinders, 4-valves per cylinder
Combustion system Direct injection
Aspiration Turbocharged with intercooler
Starting system Electrical starting 12 V - 2.5 kW
Alternator 12 V - 80 A
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 408 kg (899 lbs)
Environmental EU RCD, US EPA Tier2, BSO II, EMC & Marpol 73/78 Annex VI
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.86 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 25°C at the inlet of the fuel injection pump (ISO 3046-1) **Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665)Technical data is according to ISO 8665 / 3046
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
321 mm(12.6 in)
260 mm(10.2 in)
MIN
.138
mm
(5.4
in)
MAX
.148
mm
(5.8
in)
739
mm
(29.
1 in
)
237
mm
(9.3
in)
502
mm
(19.
8 in
)
287 mm(11,3 in)
287 mm(11,3 in)
32 m
m(1
.3 in
)
47 m
m(1
.9 in
)
345 mm(13.6 in)
666 mm (26.2 in)riser mixing elbow (option)
mixing elbow o 102
748.4 mm (29.5 in)
132
mm
(5.2
in)
389
mm
(15.
3 in
)
497.
1 m
m (1
9.6
in)
15º m
m (0
.6 in
)
55º m
m (2
.2in
)
328.2 mm(12.9 in)
248.1 mm(9.8 in)
98.8 mm (3.9 in)
333
mm
(13.
1 in
)
131 m
m (5.2i
n)
8º mm
(0.3 in)
1220 mm (48 in)
Rear view Right side view
EN
_DS
6LP
A-S
TP
2_0
413
www.yanmar.eu
6LPA-STP2 with KM2P-1 marine gear
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Note: O = Equipped on panel X = Not equipped on panel
Type of instrument panel
Function New B-type Panel New C-type Panel New D-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O O O1-2 Engine stop switch O O O1-3 Alarm buzzer (C.W. Temp., L.O. Pressure) O O O1-4 Alarm buzzer stop switch O O O1-5 Illumination switch for meters O O O2 Alarm lamp unit
Battery not charging O O OC.W. high temperature O O OL.O. low pressure O O OF.O. drain separator (water level) O O OSea water flow O O OC.W. level for fresh water tank X O OBoost pressure high O O O
3 Tachometer with hour meter O O O4 Sub meter unit
4-1 L.O. pressure meter X O O
4-2 C.W. Temperature meter X O O4-3 Boost meter (turbo) X X O
5 Quartz clock X X O
*** Gear also available in; ZF63 (Parallel) reduction ratio: 1.51 & 1.93; ZF63IV (V-drive) reduction ratio: 1.29, 1.56 & 2.00*** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Standard Package• Sensor for instrument panel • Cooling water hoses
(New B, C and D-type) • Fuel water separator (integrated with fuel filter)• Exhaust/water mixing elbow (L-type) • Alternator 12 V - 80 A
Optional• Flexible mounts (2 pcs) • Sensor for VDO instrument panels • Control heads • Exhaust mixing elbow, U-type (high riser) • Control heads • Air venting device for cooling water tank• Analog instrument panels • Various Wire Harnesses (4, 6, 10M) • VDO instrumentation for main panel
(New B,C and D-type) • Lub oil evacuation pump and fly bridge• Dual station Y harness • Dipstick for opposite side
Note: O = Equipped on panel X = Not equipped on panel
Type of instrument panel
Function New B-type Panel New C-type Panel New D-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O O O1-2 Engine stop switch O O O1-3 Alarm buzzer (C.W. Temp., L.O. Pressure) O O O1-4 Alarm buzzer stop switch O O O1-5 Illumination switch for meters O O O2 Alarm lamp unit
Battery not charging O O OC.W. high temperature O O OL.O. low pressure O O OF.O. drain separator (water level) O O OSea water flow O O OC.W. level for fresh water tank X O OBoost pressure high O O O
3 Tachometer with hour meter O O O4 Sub meter unit
4-1 L.O. pressure meter X O O
4-2 C.W. Temperature meter X O O4-3 Boost meter (turbo) X X O
5 Quartz clock X X O
*** Gear also available in; ZF63 (Parallel) reduction ratio: 1.51 & 1.93; ZF63IV (V-drive) reduction ratio: 1.29, 1.56 & 2.00*** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Standard Package• Sensor for instrument panel • Cooling water hoses
(New B, C and D-type) • Fuel water separator (integrated with fuel filter)• Exhaust/water mixing elbow (L-type) • Alternator 12 V - 80 A
Optional• Flexible mounts (2 pcs) • Sensor for VDO instrument panels • Control heads • Exhaust mixing elbow, U-type (high riser) • Control heads • Air venting device for cooling water tank• Analog instrument panels • Various Wire Harnesses (4, 6, 10M) • VDO instrumentation for main panel
(New B,C and D-type) • Lub oil evacuation pump and fly bridge• Dual station Y harness • Dipstick for opposite side
Standard engine package• S ensor for instrument panel [New B, C and D-type] • E xhaust/water mixing elbow [L-type] • C ooling water hoses • F uel water separator [integrated with fuel filter] • A lternator 12V - 80A
Optional accesories• Flexible mounts [2 pcs] • High-riser mixing elbow [instead of L-elbow]• Analog instrument panels [New B,C and D-type] • Dual station Y-harness • Sensor for VDO instrument panels • Control heads • Extension wire harness [4m, 6m, 10m] • Lub oil evacuation pump • Air venting device for cooling water tank • VDO instrumentation for main panel and fly bridge • Dipstick for opposite side
ACCESORIES
MARINE GEARS / DRIVE
Length engine and gear/drive
KMH50A
8° down hydraulic
43 kg [95 lbs]
1.67/1.67 2.13/2.13 2.43/2.43 1.22/1.21
3115/3140
1.56/1.58
2436/2405
2.04/2.10
1863/1810
2.52/2.53
1429/14232275 1784 1564
Counterclockwise
viewed from flywheel side
449 kg [990 lbs]
Model
Type
Dry weight
Reduction ratio [fwd/asn]
Propeller speed [fwd/asn]
Direction of rotation
[propeller shaft - fwd]
Dry weight engine and gear/drive
1190 mm [46.9 in]
ZF63A
8° down hydraulic
44 kg [97 lbs]
Counterclockwise
viewed from flywheel side
452 kg [996 lbs]
1205 mm [47.4 in]
NOTE: All data subject to change without notice. Text and illustrations are not binding.
Not equipped on panel
Not equipped on panel
Not equipped on panel
Not equipped on panel
Equipped on panel
Equipped on panel
DigiTAL B-TyPe PAneL new c-TyPe PAneL new D-TyPe PAneL
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Function
1-Switch unit
1-1 Key switch for GLOW/OFF/ON/START [4-position switch]
1-2 Engine stop switch
1-3 Alarm buzzer [C.W. Temp., L.O. Pressure]
1-4 Alarm buzzer stop switch
1-5 Illumination switch for meters
2-Alarm lamp unit
2-1 Battery not charging
2-2 C.W. high temperature
2-3 L.O. low pressure
2-4 F.O. drain seperator
2-5 Sea water flow
2-6 C.W. level for fresh water tank
2-7 Boost pressure high
3-Tachometer with hour meter
4-Sub meter unit
4-1 L.O. pressure meter
4-2 C.W. Temperature meter
4-3 Boost meter [turbo]
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Not equipped on panel Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panelEquipped on panel
Equipped on panel Equipped on panel Equipped on panel
Not equipped on panel Equipped on panel Equipped on panel
Not equipped on panel Equipped on panel Equipped on panel
TyPe OF inSTruMenT PAneL
5 Quartz clock
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Note: O = Equipped on panel X = Not equipped on panel
Type of instrument panel
Function New B-type Panel New C-type Panel New D-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O O O1-2 Engine stop switch O O O1-3 Alarm buzzer (C.W. Temp., L.O. Pressure) O O O1-4 Alarm buzzer stop switch O O O1-5 Illumination switch for meters O O O2 Alarm lamp unit
Battery not charging O O OC.W. high temperature O O OL.O. low pressure O O OF.O. drain separator (water level) O O OSea water flow O O OC.W. level for fresh water tank X O OBoost pressure high X O O
3 Tachometer with hour meter O O O4 Sub meter unit X
4-1 L.O. pressure meter X O O
4-2 C.W. Temperature meter X O O4-3 Boost meter (turbo) X X O
5 Quartz clock X X O
Accessories Standard Package
• Sensor for instrument panel (New B, C and D-type) • Fuel water separator (integrated with fuel filter)• Exhaust mixing elbow (L-type thru' drive) • Hydraulic Steering pump• Cooling water hoses • Alternator 12 V - 80 A
Optional• Analog instrument panels (New B,C and D-type) • Dipstick for opposite side• Flexible mounts (2pcs) • Various Wire Harnesses (4,6,10 m)• Exhaust mixing elbow, U-type (high riser transom type) • Tie Bar (for twin installation)• Lub oil evacuation pump • VDO instrumentation for main panel and fly bridge• Remark: Engine also available without Hydraulic steering pump for twin installation
New B-type Panel New C-type Panel New D-type Panel
Drive systems
Model ZT370 (Steerable Z-drive with dual prop)
Type Hydraulic Actuated Multi-friction disc clutch
Dry Weight 100 Kg
Reduction Ratio 1,65/1,65 1,78/1,78
propellor speed 2424/2424 2247/2247
Direction of rotation viewed from the stern Clockwise (rear prop) & Counterclockwise (front prop)
Lub oil specifications API class: GL5 SAE grade #80W90
Dry weight engine with sterndrive 550 kg (1213 lbs)
Maximum output at crankshaft * 232 kW@3800 rpm [315 mhp@3800 rpm]
** 225 kW@3800 rpm [306 mhp@3800 rpm]
Displacement 4.164 ltr [254 cu in]
Bore x stroke 94 mm x 100 mm [3.7 in x 3.94 in]
Cylinders 6 in line, 4-valves per cylinder
Combustion system Direct injection
Aspiration Turbocharged with intercooler
Starting system Electric starting 12V - 2.5 kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and
rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 428 kg [944 lbs]
Environmental EU: RCD BSO II EMC
US: EPA Tier2
IMO: MARPOL 73/78 Annex VI
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³; 1 kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 25°C at the inlet of the fuel injection pump [ISO 3046-1]** Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
6LPA-STZP2 with ZT370 Sterndrive
www.yanmarmarine.com
6LPA-STZP2 Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 232 kW (315 mhp) / 3800 rpm** 225 kW (306 mhp) / 3800 rpm
Cylinders 6 in line cylinders, 4- valves per cylinder
Combustion system Direct injection
Aspiration Turbocharged with intercooler
Starting system Electrical starting 12 V - 2.5 kW
Alternator 12 V - 80 A
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without sterndrive 428 kg (944 lbs)
Environmental EU RCD, US EPA Tier 2, BSO II, EMC & Marpol 73/78 Annex VI
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 25°C at the inlet of the fuel injection pump (ISO 3046-1) **Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665 : 2006)
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
230.
4 m
m (9
.1in)
504
mm
(19.
8 in)
734.
4 m
m (2
8.9
in)
MAX
.112
mm
(4.4
in)
MIN
.92
mm
(3.6
in)
784.
3 m
m (3
0.8
in)
363 mm (14.3in)406 mm (16in)769 mm (30.2in)
716.4 mm (28.2 in) 114 mm (4.5 in)830.4 mm (32.6 in)338.9 mm (13.3 in)
1169.3 mm (46 in) 856.3 mm (33.7 in)
775.
6 m
m (3
0.5
in)55
3.5
mm
(21.
8 in)
Rear view Right side view
EN
_DS
6LP
A-S
TZ
P2_
0113
www.yanmar.eu
6LPA-STZP2 with KM2P-1 marine gear
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Note: O = Equipped on panel X = Not equipped on panel
Type of instrument panel
Function New B-type Panel New C-type Panel New D-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O O O1-2 Engine stop switch O O O1-3 Alarm buzzer (C.W. Temp., L.O. Pressure) O O O1-4 Alarm buzzer stop switch O O O1-5 Illumination switch for meters O O O2 Alarm lamp unit
Battery not charging O O OC.W. high temperature O O OL.O. low pressure O O OF.O. drain separator (water level) O O OSea water flow O O OC.W. level for fresh water tank X O OBoost pressure high X O O
3 Tachometer with hour meter O O O4 Sub meter unit X
4-1 L.O. pressure meter X O O
4-2 C.W. Temperature meter X O O4-3 Boost meter (turbo) X X O
5 Quartz clock X X O
Accessories Standard Package
• Sensor for instrument panel (New B, C and D-type) • Fuel water separator (integrated with fuel filter)• Exhaust mixing elbow (L-type thru' drive) • Hydraulic Steering pump• Cooling water hoses • Alternator 12 V - 80 A
Optional• Analog instrument panels (New B,C and D-type) • Dipstick for opposite side• Flexible mounts (2pcs) • Various Wire Harnesses (4,6,10 m)• Exhaust mixing elbow, U-type (high riser transom type) • Tie Bar (for twin installation)• Lub oil evacuation pump • VDO instrumentation for main panel and fly bridge• Remark: Engine also available without Hydraulic steering pump for twin installation
New B-type Panel New C-type Panel New D-type Panel
Drive systems
Model ZT370 (Steerable Z-drive with dual prop)
Type Hydraulic Actuated Multi-friction disc clutch
Dry Weight 100 Kg
Reduction Ratio 1,65/1,65 1,78/1,78
propellor speed 2424/2424 2247/2247
Direction of rotation viewed from the stern Clockwise (rear prop) & Counterclockwise (front prop)
Lub oil specifications API class: GL5 SAE grade #80W90
Dry weight engine with sterndrive 550 kg (1213 lbs)
Shift control Mechanical or Electro-magnetic
Trim range -6° - +10°
Trailer limit 51°
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Note: O = Equipped on panel X = Not equipped on panel
Type of instrument panel
Function New B-type Panel New C-type Panel New D-type Panel1 Switch unit
1-1 Key switch for GLOW/OFF/ON/START (4-position switch) O O O1-2 Engine stop switch O O O1-3 Alarm buzzer (C.W. Temp., L.O. Pressure) O O O1-4 Alarm buzzer stop switch O O O1-5 Illumination switch for meters O O O2 Alarm lamp unit
Battery not charging O O OC.W. high temperature O O OL.O. low pressure O O OF.O. drain separator (water level) O O OSea water flow O O OC.W. level for fresh water tank X O OBoost pressure high X O O
3 Tachometer with hour meter O O O4 Sub meter unit X
4-1 L.O. pressure meter X O O
4-2 C.W. Temperature meter X O O4-3 Boost meter (turbo) X X O
5 Quartz clock X X O
Accessories Standard Package
• Sensor for instrument panel (New B, C and D-type) • Fuel water separator (integrated with fuel filter)• Exhaust mixing elbow (L-type thru' drive) • Hydraulic Steering pump• Cooling water hoses • Alternator 12 V - 80 A
Optional• Analog instrument panels (New B,C and D-type) • Dipstick for opposite side• Flexible mounts (2pcs) • Various Wire Harnesses (4,6,10 m)• Exhaust mixing elbow, U-type (high riser transom type) • Tie Bar (for twin installation)• Lub oil evacuation pump • VDO instrumentation for main panel and fly bridge• Remark: Engine also available without Hydraulic steering pump for twin installation
New B-type Panel New C-type Panel New D-type Panel
Drive systems
Model ZT370 (Steerable Z-drive with dual prop)
Type Hydraulic Actuated Multi-friction disc clutch
Dry Weight 100 Kg
Reduction Ratio 1,65/1,65 1,78/1,78
propellor speed 2424/2424 2247/2247
Direction of rotation viewed from the stern Clockwise (rear prop) & Counterclockwise (front prop)
Lub oil specifications API class: GL5 SAE grade #80W90
Dry weight engine with sterndrive 550 kg (1213 lbs)
Shift control Mechanical or Electro-magnetic
Trim range -6° - +10°
Trailer limit 51°
PERFORMANCE CURVES
INSTRUMENT PANELS
EN
_DS
6LP
A-S
TZ
P2_
0113
www.yanmar.eu
Standard engine package• Sensor for instrument panel [New B, C and D-type] • Exhaust/water mixing elbow [L-type] • Cooling water hoses • Fuel water separator [integrated with fuel filter] • Alternator 12V - 80A
Optional accesories • Flexible mounts [2 pcs] • High-riser mixing elbow [instead of L-elbow] • Analog instrument panels [New B,C and D-type] • Dual station Y-harness • Sensor for VDO instrument panels • Control heads • Extension wire harness [4m, 6m, 10m] • Lub oil evacuation pump • Air venting device for cooling water tank • VDO instrumentation for main panel and fly bridge • Dipstick for opposite side
ACCESORIES
MARINE GEARS / DRIVE
NOTE: All data subject to change without notice. Text and illustrations are not binding.
Maximum output at crankshaft * 324 kW@3300 rpm [440 HP@3300 rpm]
** 225 kW@3300 rpm [427 HP@3300 rpm]
Displacement 5.813 ltr [354 cu in]
Bore x stroke 106 mm x 110 mm [4.17 in x 4.33 in]
Cylinders 6 in line
Combustion system Direct injection
Aspiration Turbocharged with watercooled turbine housing
Starting system Electric starting 12V - 2.5 kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and
rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counter clockwise viewed from stern
Dry weight without gear 535 kg [1179 lbs]
Environmental EU: RCD EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.842 g/cm³; 1HP = 0.7355 kW * Fuel temperature 25°C at the inlet of the fuel injection pump [ISO 3046-1]** Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
6LY2A-STP w/o marine gear
www.yanmarmarine.com
6LY2A-STP Series
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 324 kW (440 hp) / 3300 rpm** 315 kW (427 hp) / 3300 rpm
Aspiration Turbocharged with watercooled turbine housing
Starting system Electrical starting 12V - 2.5kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from stern
Dry weight without gear 535 kg (1179 lbs)
Environmental 2003/44/EC, EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.842 g/cm3; 1 hp = 0.7355 kW * Fuel temperature 25°C at the inlet of the fuel injection pump (ISO 3046-1) **Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665)
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
238
mm
(9.4
in)
574 mm (22.6 in)
321 mm (12.6 in)
498 mm (19.6 in)
843
mm
(33.
2 in
)
819 mm (32.2 in)Rear view
min
. 80
mm
(3.1
in)
max
. 10
0 m
m (3
.9 in
)
226.5 mm (8,9 in)
740.5mm (29.2 in)45.5 mm (1.8 in)
Mixing elbowo 127 mm (5 in)
1274.9 mm (50.2 in)
Right side viewE
N_D
S6
LY2
A-S
TP_
041
3
www.yanmar.eu
6LY2A-STP with KM2P-1 marine gear
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior noti�cation.
www.yanmarmarine.com
Version: 2011-09
Yanmar Europe BV
0.0
50.0
100.0
150.0
200.0
250.0
300.0
350.0
1600 1800 2000 2200 2400 2600 2800 3000 3200 3400
0.0
50.0
100.0
150.0
200.0
250.0
300.0
350.0
400.0
450.0
500.0
Marine Gears/Drive
Performance Curves (Output is according ISO 8665 - Output includes +/- 6% tolerance)
Maximum output at crankshaft 353 kW@3300 rpm [480 HP@3300 rpm]
Displacement 5.813 ltr [354 cu in]
Bore x stroke 106 mm x 110 mm [4.17 in x 4.33 in]
Cylinders 6 in line
Combustion system Direct injection
Aspiration Turbocharged with seawater cooled intercooler
Starting system Electric starting 12V - 3 kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and
rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 640 kg [1411 lbs]
Environmental EU: RCD EMC
US: EPA Tier2
IMO: MARPOL 73/78 Annex VI
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.86 g/cm³; 1 kW = 1.3596 mhp = 1.3410 HP Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
6LY3-ETP with Yanmar KMH61A marine gear
www.yanmarmarine.com
6LY3-ETP Series
Configuration 24 valve, 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 353 kW (480 mhp) / 3300 rpm
Aspiration Turbocharged with seawater cooled intercooler
Starting system Electrical starting 12V - 3kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 640 kg (1411 lbs)
Environmental EPA Tier2, EU RCD, EMC, Marpol 73/78 Annex VI
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.86 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665)Technical data is according to ISO 8665 / 3046
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com or contact your supplier)
538.
6 m
m (2
1.2
in)
381 mm (15 in) 420.3 mm (16.5 in)
254.
8 m
m (1
0 in
)
793.
4 m
m (3
1.2
in)
266.6 mm (10.5 in)
39 m
m (1
.5 in
)M
IN.
MAX
. 103
mm
(4 in
)83
mm
(3.3
in)
801.3 mm (31.5 in)
843
mm
(33.
2 in
)
Front view
285 (11.2 in)1071 mm (42.2 in)
950 mm (37.4 in)122 mm (4.8 in)
145.
4 m
m (5
.7 in
)
1458.3 mm (57.4 in)
786 mm (30.9 in)
8º
256.5 mm (10.1 in)
LUB. OIL FILTERSFUEL FILTER
FUEL OUTLET
FUEL INLET
U - type elbow (optional)
Right side viewE
N_D
S6
LY3
-ET
P_0
413
www.yanmar.eu
6LY3-ETP with Yanmar KMH61A marine gear
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Multi function LCD display:- engine information - maintenance information- diagnosis messages
CAN Bus system
Engine Accessories Electronic Control System
Standard Engine Package Standard Electronic Control System• Alternator 12V- 80A • CANBUS-NMEA 2000 electronic control system• Exhaust elbow (L-type) • Ignition panel with rocker switches• Air heater • Multi-function LCD display
• Electronic control head
Optional Engine Package Optional Electronic Control system• Fuel / water separator • Second station kit for Flybridge• Exhaust elbow, U-type • Ignition panel with Keyswitch• Lub oil evacuation pump • Extension wire harnesses• Remote oil filter opposite side • Various control heads• Air vent for coolant tank • Trolling mode kit• Flexible mounts
** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Marine gear (example) **
Model KMH61A KMH61V
Type Hydraulically actuated multi-disc clucth Hydraulically actuated multi-disc clucth
Dry weight 78 kg (172 lbs) 83,9 kg (185 lbs)
Reduction ratio (fwd/asn) 1.55/1.55 2.04/2.04 2.43/2.43 1.24/1.24 1.49/1.49 1.98/1.98 2.43/2.43
Direction of rotation Clockwise & counter clockwise viewed Clockwise & counter clockwise viewed(propeller shaft - fwd) from flywheel side from flywheel side
Dry weight engine with gear 718 kg (1583 lbs) 723,9 (1596 lbs)
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Multi function LCD display:- engine information - maintenance information- diagnosis messages
CAN Bus system
Engine Accessories Electronic Control System
Standard Engine Package Standard Electronic Control System• Alternator 12V- 80A • CANBUS-NMEA 2000 electronic control system• Exhaust elbow (L-type) • Ignition panel with rocker switches• Air heater • Multi-function LCD display
• Electronic control head
Optional Engine Package Optional Electronic Control system• Fuel / water separator • Second station kit for Flybridge• Exhaust elbow, U-type • Ignition panel with Keyswitch• Lub oil evacuation pump • Extension wire harnesses• Remote oil filter opposite side • Various control heads• Air vent for coolant tank • Trolling mode kit• Flexible mounts
** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Marine gear (example) **
Model KMH61A KMH61V
Type Hydraulically actuated multi-disc clucth Hydraulically actuated multi-disc clucth
Dry weight 78 kg (172 lbs) 83,9 kg (185 lbs)
Reduction ratio (fwd/asn) 1.55/1.55 2.04/2.04 2.43/2.43 1.24/1.24 1.49/1.49 1.98/1.98 2.43/2.43
Direction of rotation Clockwise & counter clockwise viewed Clockwise & counter clockwise viewed(propeller shaft - fwd) from flywheel side from flywheel side
Dry weight engine with gear 718 kg (1583 lbs) 723,9 (1596 lbs)
PERFORMANCE CURVES
INSTRUMENT PANELS
EN
_DS
6LY
3-E
TP_
041
3
www.yanmar.eu
Standard engine package • A lternator 12V - 80A • E xhaust mixing elbow [L-type] • A ir heater
Optional engine package • F uel/water separator • H igh-riser mixing elbow [instead of L-elbow] • Lub oil evacuation pump • Remote oil filter opposite side • A ir vent for coolant tank • Flexible mounts
Standard electronic control system • CANBUS-NMEA 2000 electronic control system • Ignition panel with rocker switches • Multi-function LCD display • Electronic control head
Optional electronic control system: • Second station kit for flybridge • Ignition panel with keyswitch • Extension wire harnesses • Various control heads • Trolling mode kit
ACCESORIES ELECTRONIC CONTROL SYSTEM
NOTE: All data subject to change without notice. Text and illustrations are not binding.
MARINE GEARS / DRIVE
* Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Maximum output at crankshaft 324 kW@3300 rpm [440 mhp@3300 rpm]
Displacement 5.813 ltr [354 cu in]
Bore x stroke 106 mm x 110 mm [4.17 in x 4.33 in]
Cylinders 6 in line
Combustion system Direct injection
Aspiration Turbocharged with seawater cooled intercooler
Starting system Electric starting 12V - 3 kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and
rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 640 kg [1411 lbs]
Environmental EU: RCD EMC
US: EPA Tier2
IMO: MARPOL 73/78 Annex VI
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.86 g/cm³; 1 kW = 1.3596 mhp = 1.3410 HP Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
6LY3-ETP with Yanmar KMH61A marine gear
www.yanmarmarine.com
6LY3-ETP Series
Configuration 24 valve, 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 353 kW (480 mhp) / 3300 rpm
Aspiration Turbocharged with seawater cooled intercooler
Starting system Electrical starting 12V - 3kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 640 kg (1411 lbs)
Environmental EPA Tier2, EU RCD, EMC, Marpol 73/78 Annex VI
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.86 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665)Technical data is according to ISO 8665 / 3046
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com or contact your supplier)
538.
6 m
m (2
1.2
in)
381 mm (15 in) 420.3 mm (16.5 in)
254.
8 m
m (1
0 in
)
793.
4 m
m (3
1.2
in)
266.6 mm (10.5 in)
39 m
m (1
.5 in
)M
IN.
MAX
. 103
mm
(4 in
)83
mm
(3.3
in)
801.3 mm (31.5 in)
843
mm
(33.
2 in
)
Front view
285 (11.2 in)1071 mm (42.2 in)
950 mm (37.4 in)122 mm (4.8 in)
145.
4 m
m (5
.7 in
)
1458.3 mm (57.4 in)
786 mm (30.9 in)
8º
256.5 mm (10.1 in)
LUB. OIL FILTERSFUEL FILTER
FUEL OUTLET
FUEL INLET
U - type elbow (optional)
Right side viewE
N_D
S6
LY3
-ST
P_0
413
www.yanmar.eu
6LY3-STP with Yanmar KMH61A marine gear
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Multi function LCD display:- engine information - maintenance information- diagnosis messages
CAN Bus system
Engine Accessories Electronic Control System
Standard Engine Package Standard Electronic Control System• Alternator 12V- 80A • CANBUS-NMEA 2000 electronic control system• Exhaust elbow (L-type) • Ignition panel with rocker switches• Air heater • Multi-function LCD display
• Electronic control head
Optional Engine Package Optional Electronic Control system• Fuel / water separator • Second station kit for Flybridge• Exhaust elbow, U-type • Ignition panel with Keyswitch• Lub oil evacuation pump • Extension wire harnesses• Remote oil filter opposite side • Various control heads• Air vent for coolant tank • Trolling mode kit• Flexible mounts
** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Marine gear (example) **
Model KMH61A KMH61V
Type Hydraulically actuated multi-disc clucth Hydraulically actuated multi-disc clucth
Dry weight 78 kg (172 lbs) 83,9 kg (185 lbs)
Reduction ratio (fwd/asn) 1.55/1.55 2.04/2.04 2.43/2.43 1.24/1.24 1.49/1.49 1.98/1.98 2.43/2.43
Direction of rotation Clockwise & counter clockwise viewed Clockwise & counter clockwise viewed(propeller shaft - fwd) from flywheel side from flywheel side
Dry weight engine with gear 718 kg (1583 lbs) 723,9 (1596 lbs)
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Multi function LCD display:- engine information - maintenance information- diagnosis messages
CAN Bus system
Cran
ksha
ft To
rque
lb-
ft
Engine Accessories Electronic Control System
Standard Engine Package Standard Electronic Control System• Standard Engine Package • CANBUS-NMEA 2000 electronic control system• Exhaust mixing elbow (L-type) • Ignition panel with rocker switches• Air heater • Multi-function LCD display
• Electronic control head
Optional Engine Package Optional Electronic Control system• Fuel/Water separator • Second station kit for Flybridge• High riser mixing elbow, U-type (instead of L-elbow) • Ignition panel with Keyswitch• Lub oil evacuation pump • Extension wire harnesses• Remote oil filter opposite side • Various control heads• Air vent for coolant tank • Trolling mode kit• Flexible mounts
** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Marine gear (example) **
Model KMH61A KMH61V
Type Hydraulically actuated multi-disc clucth Hydraulically actuated multi-disc clucth
Dry weight 78 kg (172 lbs) 83,9 kg (185 lbs)
Reduction ratio (fwd/asn) 1.55/1.55 2.04/2.04 2.43/2.43 1.24/1.24 1.49/1.49 1.98/1.98 2.43/2.43
Direction of rotation Clockwise & counter clockwise viewed Clockwise & counter clockwise viewed(propeller shaft - fwd) from flywheel side from flywheel side
Dry weight engine with gear 718 kg (1583 lbs) 723,9 (1596 lbs)
PERFORMANCE CURVES
INSTRUMENT PANELS
EN
_DS
6LY
3-S
TP_
041
3
www.yanmar.eu
Standard engine package • Standard engine package • E xhaust mixing elbow [L-type] • A ir heater
Optional engine package • F uel/water separator • H igh-riser mixing elbow [instead of L-elbow] • Lub oil evacuation pump • Remote oil filter opposite side • A ir vent for coolant tank • Flexible mounts
Standard electronic control system • CANBUS-NMEA 2000 electronic control system • Ignition panel with rocker switches • Multi-function LCD display • Electronic control head
Optional electronic control system: • Second station kit for flybridge • Ignition panel with keyswitch • Extension wire harnesses • Various control heads • Trolling mode kit
ACCESORIES ELECTRONIC CONTROL SYSTEM
NOTE: All data subject to change without notice. Text and illustrations are not binding.
MARINE GEARS / DRIVE
* Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Maximum output at crankshaft 279 kW@3300 rpm [380 mhp@3300 rpm]
Displacement 5.813 ltr [354 cu in]
Bore x stroke 106 mm x 110 mm [4.17 in x 4.33 in]
Cylinders 6 in line
Combustion system Direct injection
Aspiration Turbocharged with seawater cooled intercooler
Starting system Electric starting 12V - 3 kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and
rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 640 kg [1411 lbs]
Environmental EU: RCD EMC
US: EPA Tier2
IMO: MARPOL 73/78 Annex VI
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.86 g/cm³; 1 kW = 1.3596 mhp = 1.3410 HP Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
6LY3-UTP with Yanmar KMH61A marine gear
www.yanmarmarine.com
6LY3-UTP Series
Configuration 24 valve, 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 279 kW (380 mhp) / 3300 rpm
Aspiration Turbocharged with seawater cooled intercooler
Starting system Electrical starting 12V - 3kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from flywheel side
Dry weight without gear 640 kg (1411 lbs)
Environmental EPA Tier2, EU RCD, EMC, Marpol 73/78 Annex VI
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.86 g/cm 3; 1kW = 1.3596 mhp = 1.3410 HP * Fuel temperature 40°C at the inlet of the fuel injection pumpTechnical data is according to ISO 8665 / 3046
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com or contact your supplier)
538.
6 m
m (2
1.2
in)
381 mm (15 in) 420.3 mm (16.5 in)
254.
8 m
m (1
0 in
)
793.
4 m
m (3
1.2
in)
266.6 mm (10.5 in)
39 m
m (1
.5 in
)M
IN.
MAX
. 103
mm
(4 in
)83
mm
(3.3
in)
801.3 mm (31.5 in)
843
mm
(33.
2 in
)
Front view
285 (11.2 in)1071 mm (42.2 in)
950 mm (37.4 in)122 mm (4.8 in)
145.
4 m
m (5
.7 in
)
1446.3 mm (56.9 in)
786 mm (30.9 in)
8º
256.5 mm (10.1 in)
LUB. OIL FILTERSFUEL FILTER
FUEL OUTLET
FUEL INLET
U - type elbow (optional)
Right side view
EN
_DS
6LY
3-U
TP_
041
3
www.yanmar.eu
6LY3-UTP with Yanmar KMH61A marine gear
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
Multi function LCD display:- engine information - maintenance information- diagnosis messages
CAN Bus system
Engine Accessories Electronic Control System
Standard Engine Package Standard Electronic Control System• Alternator 12V- 80A • CANBUS-NMEA 2000 electronic control system• Exhaust elbow (L-type) • Ignition panel with rocker switches• Air heater • Multi-function LCD display
• Electronic control head
Optional Engine Package Optional Electronic Control system• Fuel / water separator • Second station kit for Flybridge• Exhaust elbow, U-type • Ignition panel with Keyswitch• Lub oil evacuation pump • Extension wire harnesses• Remote oil filter opposite side • Various control heads• Air vent for coolant tank • Trolling mode kit• Flexible mounts
** Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Marine gear (example) **
Model KMH61A KMH61V
Type Hydraulically actuated multi-disc clucth Hydraulically actuated multi-disc clucth
Dry weight 78 kg (172 lbs) 83,9 kg (185 lbs)
Reduction ratio (fwd/asn) 1.55/1.55 2.04/2.04 2.43/2.43 1.24/1.24 1.49/1.49 1.98/1.98 2.43/2.43
Direction of rotation Clockwise & counter clockwise viewed Clockwise & counter clockwise viewed(propeller shaft - fwd) from flywheel side from flywheel side
Dry weight engine with gear 718 kg (1583 lbs) 723,9 (1596 lbs)
MARINE DIESEL ENGINES
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
www.yanmarmarine.com
Version: 2011-06
Yanmar Europe BV
Instrument Panels
Multi function LCD displayVarious Control heads
Engine ECU Interface
Multi function LCD display:- engine information - maintenance information- diagnosis messages
CAN Bus system
Engine Accessories Electronic Control System
Standard Engine Package Standard Electronic Control System• Standard Engine Package • CANBUS-NMEA 2000 electronic control system• Exhaust mixing elbow (L-type) • Ignition panel with rocker switches• Air heater • Multi-function LCD display
• Electronic control head
Optional Engine Package Optional Electronic Control system• Fuel/Water separator • Second station kit for Flybridge• High riser mixing elbow, U-type (instead of L-elbow) • Ignition panel with Keyswitch• Lub oil evacuation pump • Extension wire harnesses• Remote oil filter opposite side • Various control heads• Air vent for coolant tank • Trolling mode kit• Flexible mounts
Direction of rotation Clockwise & counter clockwise viewed Clockwise & counter clockwise viewed(propeller shaft - fwd) from flywheel side from flywheel side
Dry weight engine with gear 718 kg (1583 lbs) 723,9 (1596 lbs)
PERFORMANCE CURVES
INSTRUMENT PANELS
EN
_DS
6LY
3-U
TP_
041
3
www.yanmar.eu
Standard engine package • Standard engine package • E xhaust mixing elbow [L-type] • A ir heater
Optional engine package • F uel/water separator • H igh-riser mixing elbow [instead of L-elbow] • Lub oil evacuation pump • Remote oil filter opposite side • A ir vent for coolant tank • Flexible mounts
Standard electronic control system • CANBUS-NMEA 2000 electronic control system • Ignition panel with rocker switches • Multi-function LCD display • Electronic control head
Optional electronic control system: • Second station kit for flybridge • Ignition panel with keyswitch • Extension wire harnesses • Various control heads • Trolling mode kit
ACCESORIES ELECTRONIC CONTROL SYSTEM
NOTE: All data subject to change without notice. Text and illustrations are not binding.
MARINE GEARS / DRIVE
* Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Maximum output at crankshaft * 272 kW@3300 rpm [370 mhp@3300 rpm]
** 264 kW@3300 rpm [359 mhp@3300 rpm]
Displacement 5.184 ltr [316 cu in]
Bore x stroke 100 mm x 110 mm [3.94 in x 4.33 in]
Cylinders 6 in line
Combustion system Direct injection
Aspiration Turbocharged with watercooled turbine housing
Starting system Electric starting 12V - 2.5 kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and
rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from stern
Dry weight without gear 530 kg [1168 lbs]
Environmental EU: RCD EMC
Engine mounting Rubber type flexible mounts
NOTE: Fuel condition: Density at 15°C = 0.842 g/cm³; 1 mhp = 1 PS = 0.7355 kW = 0.9863 bhp* Fuel temperature 25°C at the inlet of the fuel injection pump [ISO 3046-1]** Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
6LYA-STP w/o marine gear
www.yanmarmarine.com
6LYA-STP Series23
8 m
m(9
.4 in
)
574 mm (22.6 in)
min
. 80
mm
(3.1
in)
max
. 10
0 m
m (3
.9 in
)
321 mm (12.6 in)
498 mm (19.6 in)
843
mm
(33.
2 in
)
226.5 mm (8,9 in)
740.5mm (29.2 in)
1274.9 mm (50.2 in)
819 mm (32.2 in)
45.5 mm (1.8 in)
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft * 272 kW (370 mhp) / 3300 rpm** 264 kW (359 mhp) / 3300 rpm
Aspiration Turbocharged with watercooled turbine housing
Starting system Electrical starting 12V - 2.5kW
Alternator 12V - 80A
Cooling system Fresh water cooling by centrifugal fresh water pump and rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation (crankshaft) Counter clockwise viewed from stern
Dry weight without gear 530 kg (1168 lbs)
Environmental 2003/44/EC, EMC
Engine mounting Rubber type flexible mounting
NOTE: Fuel condition: Density at 15°C = 0.842g/cm3; 1 mhp = 1PS = 0.7355 kW = 0.9863 bhp * Fuel temperature 25°C at the inlet of the fuel injection pump (ISO 3046-1) **Fuel temperature 40°C at the inlet of the fuel injection pump (ISO 8665)
Dimensions (For detailed line-drawings, please refer to our web-site: www.yanmarmarine.com)
Right side viewRear view
Mixing elbowo 127 mm (5 in)
EN
_DS
6LY
A-S
TP_
041
3
www.yanmar.eu
6LYA-STP w/o marine gear
Texts and illustrations are not binding. Yanmar Marine reserves the right to introduce adaptations without prior notification.
www.yanmarmarine.com
Version: 2011-09
Yanmar Europe BV
Marine Gears/Drive
Performance Curves (Output is according ISO 8665 - Output includes +/- 6% tolerance)
Power Torque Fuel Consumption
Instrument Panels
Standard Package• Sensor for various panels• Exhaust/water mixing elbow (L-type)
Optional• Flexible mounts • Fuel water separator• Exhaust/water mixing elbow, U-type (high riser)• Sensor for VDO instrument panels
• Alternator 12 V - 80 A
• Analog and digital (New B-type, New C-type and New D-type) instrument panels
• Control heads• Lub oil evacuation pump• Dipstick for opposite side
Function New B-type Panel New C-type Panel New D-type Panel1 Switch unit
1-1 1-1 Key switch (starter switch) O O O1-2 Engine stop switch O O O1-3 Alarm buzzer (C.W. Temp., L.O. Pressure) O O O1-4 Alarm buzzer stop switch O O O1-5 Illumination switch for meters O O O2 Alarm lamp unit
Battery not charging O O OC.W. high temperature O O OL.O. low pressure O O OSea water flow O O OC.W. level for fresh water tank O O OBoost pressure high O O O
3 Tachometer with hour meter O O O4 Sub meter unit
4-1 L.O. pressure meter X O O
4-2 C.W. Temperature meter X O O4-3 Boost meter (turbo) X X O5 Quartz clock X X O
Note: O = Equipped on panel X = Not equipped on panel
Model ZF80-1A: 8° Angle MG5050A: 10° Angle KMH60AType Wet and multi-disc clutch Wet and multi-disc clutch Hydraulically actuated multi-disc clucth
Dry weight 64 kg (141 lbs) 80 kg (176 lbs) 58 kg (128 lbs)
Function New B-type Panel New C-type Panel New D-type Panel1 Switch unit
1-1 1-1 Key switch (starter switch) O O O1-2 Engine stop switch O O O1-3 Alarm buzzer (C.W. Temp., L.O. Pressure) O O O1-4 Alarm buzzer stop switch O O O1-5 Illumination switch for meters O O O2 Alarm lamp unit
Battery not charging O O OC.W. high temperature O O OL.O. low pressure O O OSea water flow O O OC.W. level for fresh water tank O O OBoost pressure high O O O
3 Tachometer with hour meter O O O4 Sub meter unit
4-1 L.O. pressure meter X O O
4-2 C.W. Temperature meter X O O4-3 Boost meter (turbo) X X O5 Quartz clock X X O
Note: O = Equipped on panel X = Not equipped on panel
Model ZF80-1A: 8° Angle MG5050A: 10° Angle KMH60AType Wet and multi-disc clutch Wet and multi-disc clutch Hydraulically actuated multi-disc clucth
Dry weight 64 kg (141 lbs) 80 kg (176 lbs) 58 kg (128 lbs)
NOTE: All data subject to change without notice. Text and illustrations are not binding.
MARINE GEARS / DRIVE
* Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
Model
Type
Dry Weight
Reduction Ratio [fwd/asn]
Propeller speed [fwd/asn]
Direction of rotation
[propeller shaft - fwd]
Dry weight engine and gear/drive
Length engine and gear/drive
ZF80-1A: 8° Angle
Wet and multi-disc clutch
64 kg [141 lbs]
Clockwise & Counterclockwise
viewed from stern
594 kg [1310 lbs]
1556 mm [61 in]
Mg5050A: 10° Angle
Wet and multi-disc clutch
80 kg [176 lbs]
Clockwise & Counterclockwise
viewed from stern
610 kg [1345 lbs]
1556 mm [61 in]
KMH60A
Hydraulically actuated multi-disc clutch
58 kg [128 lbs]
Clockwise & Counterclockwise
viewed from stern
588 kg [1296 lbs]
1556 mm [61 in]
2.00/2.00 1.55/1.55
2000/2000
1.20/1.20
1550/15502583/2583
2.50/2.50 2.04/2.04
1520/1520
1.41/1.41
1240/12402199/2199
2.85/2.85 2.55/2.55
1216/1216
1.57/1.57
1088/10881975/1975
Not equipped on panel Not equipped on panel Equipped on panel
DigiTAL B-TYPe PAneL new c-TYPe PAneL new D-TYPe PAneL
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Function
1-Switch unit
1-1 Key switch [starter switch]
1-2 Engine stop switch
1-3 Alarm buzzer [C.W. temp., L.O. pressure]
1-4 Alarm buzzer stop switch
1-5 Illumination switch for meters
2-Alarm lamp unit
2-1 Battery not charging
2-2 C.W. high temperature
2-3 L.O. low pressure
2-4 Sea water flow
2-5 C.W. level for fresh water tank
2-6 Boost pressure high
3-Tachometer with hour meter
4-Sub meter unit
4-1 L.O. pressure meter
4-2 C.W. temperature meter
4-3 Boost meter [turbo]
5 Quartz clock
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel Equipped on panel
Equipped on panel Equipped on panel
Equipped on panel
Equipped on panel
Equipped on panelEquipped on panel
Not equipped on panel Equipped on panel Equipped on panel
Not equipped on panel Equipped on panel Equipped on panel
Not equipped on panel Not equipped on panel Equipped on panel
TYPe oF inSTruMenT PAneL
Standard engine package• Sensor for various panels• E xhaust/water mixing elbow [L-type] • A lternator 12V - 80A
ACCESORIES
optional accesories: • Flexible mounts• Fuel water separator• High-riser/water mixing elbow [instead of L-elbow]• Sensor for VDO instrument panels• Analog and digital [new B-type, new C-type and new D-type] instrument panels• Control heads• Lub oil evacuation pump• Dipstick for opposite side
MARINE DIESEL ENGINES
8LV-320/350/370 Series
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft 235 kW @ 3.800 rpm / 272 kW @ 3.800 rpmaccording ISO 8665:2006 (320 mhp @ 3.800 rpm) / (370 mhp @ 3.800 rpm)
NOTE: All data subject to change without notice. Text and illustrations are not binding.
DRIVE SySTEMS
* Other marine gearboxes and configurations available upon request. Contact your local supplier for more information.
• yanmar CAN-bus control system • Electronic CAN-bus control-head • Multi-function colour display • N MEA2000 or J1939 gauge output • S econd or third station - optional
CONTROL SySTEM
KMH50A [down angle 8°]
KMH52V [integral V-drive 12°]
Hydraulic Actuated Multi-friction disc clutch
Hydraulic Actuated Multi-friction disc clutch
43 kg excl. foot and cooler [=15.5 kg]
59 kg excl. foot and cooler [=20 kg]
1.22/1.22
Clockwise & Counterclockwise viewed from the stern
Clockwise & Counterclockwise viewed from the stern
API class: CF or higher SAE grade #30
API class: CF or higher SAE grade #30
494 kg [1089 lbs]
514 kg [1133 lbs]
Model
Type
Dry weight
Reduction ratio [fwd/asn]
Direction of rotation
Lub oil specifications
Dry weight engine and gear
Model
Type
Dry weight
Reduction ratio [fwd/asn]
Direction of rotation
Lub oil specifications
Dry weight engine and gear
1.67/1.67
1.58/1.58
2.13/2.13
2.08/2.08
2.43/2.43
2.47/2.47
EN
_DS
8LV
320
/350
/370
_071
3
MARINE DIESEL ENGINES
8LV-320Z/350Z/370Z Series
NOTE: Fuel condition: Density at 15°C = 0.84 g/cm³Fuel temperature 40°C at the inlet of the fuel injection pump [ISO 8665: 2006]Technical data is according to ISO 8665: 2006/3046-1
DIMENSIONS
MARINE DIESEL ENGINES
Configuration 4-stroke, vertical, water cooled diesel engine
Maximum output at crankshaft 235 kW @ 3.800 rpm / 272 kW @ 3.800 rpmaccording ISO 8665:2006 (320 mhp @ 3.800 rpm) / (370 mhp @ 3.800 rpm)
Maximum output at crankshaft 235 kW@3800 rpm [320 mhp@3800 rpm]
according ISO 8665: 2006 257 kW@3800 rpm [350 mhp@3800 rpm]
272 kW@3800 rpm [370 mhp@3800 rpm]
Displacement 4.46 ltr [272.24 cu in]
Bore x stroke 86 mm x 96 mm [3.38 in x 3.78 in]
Cylinders 8 in V-90°
Combustion system Direct injection Common Rail System
Compression ratio 15:8
Low Idle rpm 550 rpm
Aspiration Turbocharged with twin TC
Electric system 12V
Alternator 12V - 180A
Start-assist Glow-plug system
Cooling system Fresh water cooling by centrifugal fresh water pump
Sea water cooling by rubber impeller seawater pump
Lubrication system Enclosed, forced lubricating system
Direction of rotation [crankshaft] Counterclockwise viewed from flywheel side
Dry weight without gear 435 kg [959 lbs]
Environmental EU: RCD EMC
US: EPA Tier3
Engine mounting Rubber type flexible mounting
EN
-8LV
Z_0
813
MARINE DIESEL ENGINES
EN
-8LV
Z_0
813
www.yanmar.eu
NOTE: All data subject to change without notice. Text and illustrations are not binding.
DRIVE SySTEMS
• yanmar CAN-bus control system • Electronic CAN-bus control-head • Multi-function colour display • N MEA2000 or J1939 gauge output • S econd or third station - optional