xA 2004-2007 xB 2004-2008 tC 2005-2007 xD 2008 99-8209 · 2010. 7. 11. · Scion tC 2005-2007 4 Disconnect the negative battery ter-minal to prevent an accidental short circuit. 1
Post on 23-Apr-2021
2 Views
Preview:
Transcript
INSTALLATION INSTRUCTIONS FOR PART 99-8209
99-8209
APPLICATIONSSCION
xA 2004-2007 xB 2004-2008tC 2005-2007xD 2008
KIT FEATURES
• DIN Radio Provision with Pocket• ISO Mount Radio Provision with Pocket
A) Radio Housing • B) Brackets Set 1 • C) Brackets Set 2 • D) ISO Snap-In Brackets • E) Trim Plate
KIT COMPONENTS
A
Phillips Screwdriver • Panel Removal Tool • Socket Set
1-800-221-0932 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
C
TOOLS REQUIRED:
D E
Dash Disassembly- SCION xA 2004-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1- SCION xB 2004-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2- SCION xB 2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3- SCION tC 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4- SCION xD 2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Kit Assembly- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6- ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .7
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
TABLE OF CONTENTS
99-8209
*Note: Refer also to the instructions included with the aftermarket radio.
99-8209 DASH DISASSEMBLY
Scion xA 2004-2007A
OFF
HI
B
OFF
HI
C
OFF
HI
D
OFF
HI
E
1
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
1
Pull outward on the (3) climate con-trol knobs and remove. (Figure A)
2
Remove (2) Phillips screws frombehind the outer two climate knobs.(Figure B)
3
Unsnap and remove the trim pieceson each side of the climatecontrol/ashtray/pocket assembly.(Figure C)
4
Remove (2) Phillips screws from thebottom of the climate control/radiotrim panel and unsnap and removethe entire panel. (Figure D)
5
Remove (4) 10 MM bolts securing theradio. Unplug and remove the radio.(Figure E)
6
Continue to final assembly.
99-8209 DASH DISASSEMBLY
Scion xB 2004-2007
2
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
1
Pull outward on the (3) climate con-trol knobs and remove. (Figure A)
2
Remove (2) Phillips screws frombehind the outer (2) knobs. (Figure B)
3
Unsnap and remove the entire panelsurrounding the climate controls andthe radio. (Figure C)
4
Remove (4) 10 MM bolts securing theradio. Unplug and remove the radio.
5
Continue to final assembly.
OFF
HI
A
OFF
HI
B
OFF
HI
C
99-8209 DASH DISASSEMBLY
Scion xB 2008
3
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
1
Unclip and remove the trim panelaround the radio including the a/cvents. (Figure A)
2
Unclip and remove the trim panel atthe bottom edge of the dash cavity.(Figure A)
3
Remove (4) 10 MM bolts securing theradio. Unplug and remove the radio.(Figure B)
4
Continue to final assembly.
A
B
99-8209 DASH DISASSEMBLY
Scion tC 2005-2007
4
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
1
Unsnap trim from around shifter. (Notnecessary to be removed). (Figure A)
2
Unsnap and remove panel fromaround radio. (Including climate con-trols and radio door). (Figure B)
3
Remove (2)10MM nuts from the topmounting locations and two Phillipsscrews from the bottom mountinglocations to remove the radio. (Figure C)
4
Continue to final assembly.
A
B
C
99-8209 DASH DISASSEMBLY
Scion xD 2008
5
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.
1
Unclip radio trim panel. Unplug andremove panel. (Figure A)
2
Remove (4) Phillips screws securingthe radio. Unplug and remove radio.(Figure B)
3
Remove factory brackets from radio.Retain brackets for use during kitassembly. (Figure C)
4
Continue to final assembly.
A
B
C
99-8209 KIT ASSEMBLY
6
A
B
CD
Slide the Mounting Brackets onto thesides of the Radio Housing until theside clips engage. Note: Use bracketset 1 for xA, xB, and tC. Use bracketset 2 for the 2008 xB and xD. (Figure A)
1
For bracket set 1 cut and remove allmounting tabs except the tabs beingused for your application. Note: Tabsare marked xA, xB and tC. For bracketset 2 skip to step 3. (Figure B)
2
Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs outward. (Figure C)
3
Slide the aftermarket radio into thecage until it snaps into place. (Figure D)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
DIN RADIO PROVISION WITH POCKET
99-8209 KIT ASSEMBLY
7
Slide the corresponding mountingbrackets onto the sides of the RadioHousing until the side clips engage.Note: Use bracket set 1 for xA, xB,and tC Use bracket set 2 for the 2008xB and xD. (Figure A)
1
For bracket set 1 cut and remove allmounting tabs except the tabs beingused for your application. Note: Tabsare marked xA, xB and tC. For bracketset 2 skip to step 3. (Figure B)
2
Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure C)
3
Slide the radio into the radio housinguntil it snaps into place. (Figure D)
4
Snap the Trim Plate onto the front ofthe Radio Housing. (Figure D)
5
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
ISO MOUNT RADIO PROVISION WITH POCKET
A
B
CD
99-8209 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.
8
NOTES
9
99-8209
99-8209 INSTRUCTIONS
1-800-221-0932 REV. 10/05/07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-8209
www.metraonline.com
top related