Pneumatic tools - Unior tools - Hand toolsuniortools.com/media/Attachments/Rocno_orodje/Eng/ostalo/pneumatic... · Unior’s pneumatic tools are a welcome addition ... • Cutting
Post on 06-Feb-2018
219 Views
Preview:
Transcript
www.uniortools.com
Pneumatic tools
Future tools
Such tools have a lot of advantages over electric tools due to its safety, duration, and economy. Up until now, these tools have convinced many vehicle painters, welders or construction workers, but they found their place also in industrial manufactur-ing and in the process of setting up various products.
Unior’s pneumatic tools are a welcome addition during hard work on steel constructions, bridges and in shipbuilding. There are always tasks which demand feeling and accuracy, or diffi cult-to-reach places which cannot be reached with larger tools.
With Unior’s pneumatic tools, each task will be mas-tered properly and with feeling, and you will save hours of time-consuming handwork.
Warning!
• Read instructions before using the tool!
• Always wear protective equipment!
Have you ever asked yourself why modern industri-al plants and workshops are equipped with pneu-matic and not with electric hand tools?
Guarantee 2 y
ears
Hig
h quality
Hig
h quality
2 years of Guarantee
Hig
h quality
2 years of Guarantee
Vis
oka kakovost
2 leti garancije
Why pneumatic tools?
EconomyThe advantage over pneumatic tools can already be noticed on the electricity bill. It is considerably lower when these tools are used intensely, because the compressor for the production of certain kinetic energy uses less electricity than an equal sum of electric tools.
DurabilityPneumatic tools last for hours of uninterrupted intense work and have longer useful life than electric tools. Because they do not have a motor, they cannot overheat and overload. Practically they do not need any maintenance.
SafetyThere is no risk of electrical stroke or explosion – among all working appliances with their own propulsion, pneumatic tools are the safest and can be used with no hesitation also in damp places or wet surfaces.
ErgonomicsBecause there is no (electro) motor that could hinder work, planners can closer the form to ideal ergonomic shape and intended use. For the same reason, pneumatic tools are lighter than electric tools, which is especially important when working with the tools the whole day.
Legend of symbols used in catalogue
Code
Weight in grams
Dimension
Number of items
Outer dimension in mm
1/2” point
3/8” point
3/4” point
1” point
1. 1/2” point
Guarantee 2 y
ears
Hig
h quality
Hig
h quality
2 years of Guarantee
Hig
h quality
2 years of Guarantee
Vis
oka kakovost
2 leti garancije
Contact information
Photographs in this catalogue are symbolic.
UNIOR d.d.Kovaška cesta 10, 3214 ZREČE, Slovenia
T: +386 3 757 81 00F: +386 3 576 26 43
I: www.uniortools.comE: sales@unior.si
4
1/4”
3/8”
3/4”
1/4”
3/8”
1/2”
1/4”
3/8”
1/2”
1/4”
3/4”
3/8”
1/2”
1/2”
1/2”
1/2”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”1/4”
1/4”
3/8”
3/8”
1/4”
1/2”
3/8”
1506KN7 617795 1/4" 20
1506KN7 617796 3/8" 20
1506KZ7 617793 1/4" 20
1506KZ7 617794 3/8" 20
1506KZ10 621452 3/8" 24
1506KZ10 621453 1/2" 24
1506KZ10 621454 3/4" 27
1507Z7 617797 1/4” 14
1507Z7 617798 3/8” 19
1507Z7 618483 1/2” 22
1507Z10 621455 3/8" 17
1507Z10 621456 1/2" 24
1507Z10 621457 3/4" 27
4
How to fasten with the right wrench?
How to connect Unior Pneumatic tools?
Alternative connection between article 1508 A and 1508 B when working on the cleanest surfaces (for example the dashboard of a car).
Air supply
Maximum air pressure: 9,5 bar
621473 Art. 1503
617736 Art. 1501
617737 Art. 1502
617735 Art. 1500
621453 Art. 1506 KZ10
617794 Art. 1506 KZ7621452 Art. 1506 KZ10
621454 Art. 1506 KZ10
617793 Art. 1506 KZ7
617797 Art. 1507 Z7
617798 Art. 1507 Z7621455 Art. 1507 Z10
Art. 1505
3/8” = 617745 (11x16/9m)3/8” = 617748 (11x16/12m)
1/4” = 617743 (6.5x10/9m)1/4” = 617744 (8x12/9m)1/4” = 617746 (6.5x10/12m)1/4” = 617747 (8x12/12m)
617767 Art. 1508 A
617768 Art. 1508 B
Code Inlet thread mm
5
1/4”
3/8”
3/4”
1/4”
3/8”
1/2”
1/4”
3/8”
1/2”
1/4”
3/4”
3/8”
1/2”
1/2”
1/2”
1/2”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”1/4”
1/4”
3/8”
3/8”
1/4”
1/2”
3/8”
5
How to connect Unior Pneumatic tools?
Alternative connection between article 1508 A and 1508 B when working on the cleanest surfaces (for example the dashboard of a car).
www.uniortools.com
617793 Art. 1506 KZ7
617794 Art. 1506 KZ7621452 Art. 1506 KZ10
617797 Art. 1507 Z7
618483 Art. 1507 Z7621456 Art. 1507 Z10
617798 Art. 1507 Z7621455 Art. 1507 Z10
617728 Art. 1517 P
617729 Art. 1517 S
615320 Art. 1541
615322 Art. 1561
615319 Art. 1551
615321 Art. 1562
615324 Art. 1571
617718 Art. 1514 A1
617719 Art. 1514 A2
617720 Art. 1514 A3
617721 Art. 1514 A4
617722 Art. 1514 A5
617723 Art. 1514 A6
615325 Art. 1591
615326 Art. 1592
617690 Art. 1596
617691 Art. 1597
615323 Art. 1572
617733617713 Art. 1510
617714617715 Art. 1514
617726 Art. 1515
617727 Art. 1515 H
617731 Art. 1516
617732 Art. 1516 A
615318 Art. 1531
617730 Art. 1518
Art. 1205/1610501 D = 115 mm610502 D = 125 mm
Art. 1205/2610505 D = 115 mm610506 D = 125 mm
Art. 1207/2610509 D = 115 mm610510 D = 115 mm610511 D = 125 mm610512 D = 125 mm
Art. 1200/1610484 D = 115 mm610485 D = 125 mm
Art. 1200/2610488 D = 115 mm610489 D = 125 mm
Art. 1202/2610492 D = 115 mm610493 D = 115 mm610494 D = 125 mm610495 D = 125 mm
Art. 1216610539 D = 115 mm610540 D = 115 mm610541 D = 115 mm610542 D = 115 mm610543 D = 115 mm610544 D = 125 mm610545 D = 125 mm610546 D = 125 mm610547 D = 125 mm610548 D = 125 mm
6
Pneumatic sanderPneumatic sanderPneumatic sander
For a perfect surfaceThe advantage of this silent and compact tool is its ergonomically shaped handle, which al-lows good grip and prevents slipping, on the other hand it is suitable for left-handers as well as for right-handers. The sander has an additional function of sucking dust that is produced during work. It is also distinguished with a handy switch and a silent and powerful drive. It operates on the principle of eccentric circular moves without producing vibrations. On the working platform, the pneumatic sander does not leave edges and is therefore suitable for larger surfaces. An integrated speed regulator allows all kinds of works – from aggressive sanding to soft smoothening during fi nishing works.
Pneumatic sander
No. L A D 617733 2.5 220 105 150 1186
617713 5 220 105 150 1186
Advantages• The ergonomic shape of the handle enables good
grip and prevents gliding
• Suitable for left-handers as well as for right-handers
• Silent and powerful drive
• Handy on/off switch
• Exhaustion of parts into a bag for a cleaner workplace
• Flexible and robust pipe for cleaning dust
• It does not leave edges on the working platform
• Better work conditions due to minimal vibrations
• Extreme power based on its weight (1.2 kg)
Use• Vehicle workshops
• Preparation of different working platforms for further process
• Ideal for grinding construction steel, metals and wood
• Free speed 10.000 revolutions per minute
• Maximum workingpressure: 6.2 bar
• Air consumption: 212 l/min
• Air inlet: 1/4”
• VELCRO™ sander pad
1510
7
Operating principle of the sanderIt operates on the principle of eccentric circular
moves, as shown in the picture. The VELCRO™ system enables a simple fastening of the sanding
pad. An additional exhaust of the sander prevents dusting in the room.
Environmentally friendly polyurethane foam which prevents vibrations
Durable and fiberglass-covered surface
The VELCRO™ system for fastening sander pads
Suction of dust from the working platform
The basis of sander is VELCRO™ system which is: quick,
simple and safe to mount and unmount various sander pads.
This system is being used for various occasions - the best known example is training
shoes with VELCRO™ fastening.
The advantage of the sander pad
8
• Used for cutting sheet, bolts and removing welding slags, rivets, plaster and tiles
• With spring, quick change retainer as spare parts
• Bore diameter: 9.1 mm
• Air consumption: 250 l/min
• Air inlet: 1/4”
Stroke pneumatic hammerStroke pneumatic hammerStroke pneumatic hammerStroke pneumatic hammerStroke pneumatic hammerStroke pneumatic hammer
Enormous striking powerThe stroke pneumatic hammer is used for repairing and handling of bodywork, cutting body sheet and screws, removing welds and other things.
Besides that, it is also suitable for working on various types of walls, concrete, stones, bricks, steel, and alloy of light metals. For each type of material and work, a suitable Unior chisel is needed. The pneumatic stroke hammer has a change retainer, with which change of chisels is much easier, so the work with such tool becomes more effi cient and safe to use.
Stroke pneumatic hammer
Advantages• Light and compact tool, used also
in small rooms
• Wide range of use
• Change retainer
Use• Car industry
• Cutting of sheet metal and screws
• Removal of welds
• Working on walls, concrete, stones, bricks, steel, light metals
Spare parts
alternate change retainer for art. 1514 (617717)
alternate spring forart. 1514 (617716)
stroke per minute L A HEX
617714 3000 170 150 10 1600
617715 2100 225 150 10 2400
1514
9
Chisels for stroke pneumatic hammer art. 1514
Flat chisel 1514 A1Shaping and cleaning of welds, trimming of bolts and nails, production of slots, cleaning and evening of uneven surfaces.
Pointed chisel 1514 A2 Removing pins and rivets, making holes.
Rivet and welding slag chisel 1514 A3Removing rivets and welding slags.
Sheet cutting chisel 1514 A4 Cutting sheet metal.
“v” edge chisel 1514 A5Cutting sheet metal.
Spade chisel 1514 A6Shaping and cleaning of welds, trimming of bolts and nails, production of slots, cleaning and evening of uneven surfaces.
10
• Reversible turning
• Free speed: 1.800 revolutions per minute
• Maximum working pressure: 6.2 bar
• Air consumption: 113 l/min
• Air inlet: 1/4”
• Chuck capacity: 1.0 - 10 mm
• Spindle thread: 3/8”, 24 UNF
• Internal hose size: 10 mm
Pneumatic drillsPneumatic drillsPneumatic drills
Less vibrations, more powerThe pneumatic drill enables exact drilling into metals. The speed and rotation direction are adaptable, the handle, made of plastic material, eases the vibrations, which enables full controlled drilling. This lightweight, handy, but powerful drill is suitable also because of its quick change retainer. The robust body and qualitative production ensure a long useful life of the product. Pneumatic drills are an ideal working solution in workshops and industrial manufacturing.
L A 617726 190 150 1150
Advantages• Extreme power based on its size
• Lightweight, compact and easy-to-master tool
• Handy turn-on switch
• Ergonomically shaped handle of plastics material dampens vibrations
• Reversible turning
• Quick change retainer
Quick change retainer 3/8”enables simple exchange ofvarious drills
Fast switch which needs a minimal force for turning on the tool
The handle is soft and protects the user from “cold” and vibrations.
Durable housing with very goodweight/power ratio
Simple switching of the direction of rotation
Pneumatic drill 1515
11
• Reversible turning
• Free speed: 800 revolutions per minute
• Maximum working pressure: 6.2 bar
• Air consumption: 113 l/min
• Air Inlet: 1/4”
• Chuck capacity: 1.5 - 13 mm
• Spindle thread: 3/8”, 24 UNF
• Internal hose size: 10 mm
L A 617727 220 150 1570
Pneumatic drill with handle
Advantages• Extreme power based on size
• Lightweight and easy-to-master tool
• Adjustable handle for better support
• Handy turn-on switch
• Ergonomically shaped handle for work without effort
• Plastic cover for handle dampens vibrations
• Reversible turning
• Quick change retainer
Quick change retainer 3/8” enables simple exchange of various drills
Fast switch which needs a minimal force for turning on the tool
The handle is soft and protects the user from “cold” and vibrations
Durable housing with very goodweight/power ratio
Simple switching of the direction of rotation
The adjustable handle offers additional support, prevents slipping of hands
1515H
12
• Free speed 25.000 revolutions per minute
• Maximum working pressure: 6.2 bar
• Air consumption: 113 l/min
• Air inlet: 1/4”
• Collet capacity: 6 mm
• Internal hose size: 10 mm
Pneumatic die grinderPneumatic die grinderPneumatic die grinderPneumatic die grinderPneumatic die grinderPneumatic die grinder
Extensive power in small packagesThe pneumatic die grinder is meant for fi nishing precision engineering, tooling, car- and aero-nautical industry. It is especially suitable for grinding, polishing, milling, shaping or cleaning of welds and products of metal, glass, plastic materials or wood. All kinds of standard grind, polish plugs and grinding caps that are available on the market can be used.
Pneumatic die grinder
L A 617731 155 60 390
Quick change retainer of the grinder makes the work much easier and saves time when retaining due to two enclosed wrenches
The rubber protecting the user from vibrations is soft to the touchFast and simple
continuously variable regula-tion of rpm
Safety lever which prevents accidental turn-on and
injuries to the user
Advantages• Safety lever for prevention of accidental
turn-on
• Simple clamping of thin cut-off wheels (grinding/polishing pins) and other parts/extensions
• Extreme power based on size
• Lightweight and compact tool
• Continuously variable regulation of rpm
Use• Precise grinding
• Full grinding
• Tool industry
• Car industry
• Aeronautical industry
• Cleaning of welds
• Cleaning of concrete and wall surfaces
• Cleaning of wooden surfaces
• Removal of colours and varnish
• Removal of rust
• Grinding of bearings
• Grinding of motor valves
• Grinding of gears and coils
• Various other surfaces
1516
13
• Free speed: 20.000 revolutions per minute
• Maximum working pressure: 6.2 bar
• Air consumption: 113 l/min
• Air inlet: 1/4”
• Collet capacity: 6 mm
• Internal hose size: 10 mm
Advantages• This angle edition enables access to
difficult-to-reach places which normal grinders cannot reach
• Safety lever which prevents accidental turn-on
• Simple clamping of thin cut-off wheels (grinding/polishing pins) and other parts/extensions
• Extreme power based on size
• Small and compact tool
• Continuously variable regulation of rpm
Use• Precise grinding
• Full grinding
• Tool industry
• Car industry
• Aeronautical industry
• Cleaning of welds
• Cleaning of concrete and wall surfaces
• Cleaning of wooden surfaces
• Removal of colours and varnish
• Removal of rust
• Grinding of bearings
• Grinding of motor valves
• Grinding of gears and coils
• Various other surfaces
L A 617732 162 76 520
Quick change retainer of the grinder makes the work much easier and saves time when retaining due to two enclosed wrenches
The rubber protecting the user from vibrations is soft to the touchFast and simple
continuously variable regula-tion of rpm
Safety lever which pre-vents accidental turn-on and injuries to the user
The angle type of the pneumatic die grinder allows us to reach places unable to reach with standard pneumatic die grinders.
Pneumatic angle die grinder 1516A
14
• Free speed: 4.500 revolutions per minute
• Maximum working pressure: 6.2 bar
• Air consumption: 340 l/min
• Air inlet: 1/4”
• Internal hose size: 10 mm
• Spindle thread: 5/8”
Pneumatic sanderPneumatic sanderPneumatic sander
Adaptability on requestThe handy pneumatic angle sander is used for light works in manufacturing, especially in the car industry.
This angle sander is well-built and equipped with a handle which can be placed on the left or on the right side of the tool. When trying to work in small and diffi cult-to-reach places, the handle can be removed.
The polishing paper is placed on the carrying surface of the tool with the help of a fastening nut, which has to be fastened by hand fi rst and afterwards with the enclosed wrench.
Pneumatic angle sander
Advantages• Light and compact tool
• Suitable for left-handers as well as right-handers
• Removable handle
• Handy turn-on switch
Use• Grinding of welds
• Grinding of sharp edges
• Reparation of small uneven surfaces
L A D 617729 375 100 175 2165
1517S
15
Pneumatic polisherPneumatic polisherPneumatic polisherPneumatic polisherPneumatic polisherPneumatic polisherPneumatic polisherPneumatic polisherPneumatic polisherPneumatic polisherPneumatic polisherPneumatic polisher
Polishing without effortThe pneumatic polisher is used especially in the car industry. The polisher is well-built and equipped with an adjustable handle which can be placed on the left or on the right side of the tool. When trying to work in small and diffi cult-to-reach places, the handle can be removed.
This polisher has less rpm than grinding machines; therefore special polishing textile can be placed on the carrying surface. It is not fastened with a nut, but only with a suction cup to the polishing textile.
Advantages• Light and compact tool
• Suitable for left-handers as well as right-handers
• Removable handle
• Handy turn-on switch
Use• Grinding of welds
• Grinding of sharp edges
• Reparation of small uneven surfaces
Pneumatic angle polisher
• Free speed 2.500 revolutions per minute
• Maximum working pressure: 6.2 bar
• Air consumption: 340 l/min
• Air inlet: 1/4”
• Internal hose size: 10 mm
• Spindle thread: 5/8”
L A D 617728 375 100 175 2165
1517P
16
Pneumatic grinderPneumatic grinderPneumatic grinderPneumatic grinderPneumatic grinderPneumatic grinder
Without extra layersIt is used to perform various kinds of work. It removes extra material like rust, colour and similar very fast. It is suitable for shaping of welds and for grinding various complex forms and cutting construction materials.
Tool is supplied with replaceable handle and protection from fast spinning parts which pro-tects the user from injuries of potential fl ying parts.
A tool safety mechanism prevents unwanted switch-on of the tool and so protects the user from accidental threats or injuries. Saying so, the user cannot turn on the switch by pressing only the switch, but fi rst has to shift the safety lever which prevents unwanted turn-on.
Pneumatic angle grinder
Advantages• Safety lever prevents unwanted turn-on
• Removable handle
• Protection from rotating parts
• Also usable in small rooms/places
Use• Tooling
• Cleaning of welds
• Cutting profile carriers and sheet metal
• Cleaning of concrete, walls and wooden surfaces
• Removal of colours varnish and rust
• Other home use
L A D 617730 230 90 125 1920
• Free speed: 11.000 revolutions per minute
• Maximum working pressure: 6.2 bar
• Air consumption: 170 l/min
• Air inlet: 1/4”
• Spindle thread: 3/8”
1518
17
Pneumatic ratchetsPneumatic ratchetsPneumatic ratchetsPneumatic ratchetsPneumatic ratchetsPneumatic ratchets
Unlimited ways of useThe Unior ratchet is a must-have tool in car repairs, domestic workshops, and nearly all other demanding industrial businesses. This well-produced implementation of the tool’s head ena-bles greater fl exibility in diffi cult-to-reach places and a wider spectrum of use.
It is adaptable to the user's hand, making it easy to use and at the same time enables fast change of the tool working direction. Endurable gear wheels are produced in accordance with the most demanding quality standards.
A L Torque 615319 1/2” 45 254 81 1200
A L Torque 615318 3/8” 37 165 27 520
Pneumatic reversible ratchet 3/8”
• Free speed: 250 revolutions per minute
• Max. torque: 27 Nm
• Maximum working pressure: 6.2 bar
• Air consumption: 71 l/min
• Air inlet: 1/4”
• Max. bolt size: M6
Pneumatic reversible ratchet 1/2”
• Free speed: 160 revolutions per minute
• Max. torque: 81 Nm
• Maximum working pressure: 6.2 bar
• Air consumption: 113 l/min
• Air inlet: 1/4”
• Max. bolt size: M10
Advantages• Light and compact tool
• Quality production
• Handy turn-on switch
• Fast and handy adjustment of the rotation direction
• Sluice-gate enabling prevention of air inlet into the tool
Use• Car industry
• Agricultural equipment
• Heavy industry
• Larger construction machinery
• Individual mountingImportant!
• The use of Unior IMPACT sockets is recommended.
1531 1551
18
Universal use for different types of workUnior’s pneumatic hammers with controlled torque enable fast screwing (fastening and unfastening) and can handle the most hard-to-handle nuts and oxidized screws. They are uni-versal and can therefore be used in diff erent types of mounting where maximum torques and forces are needed. They are becoming more and more popular also in domestic garages.
The basic functions of all Unior pneumatic hammers are the same as – they all enable torque adjustment and determination of the direction of rotation, but diff er from the maximum torque, way of regulation and overall maximum socket size.
Pneumatic hammersPneumatic hammersPneumatic hammers
3/8” pneumatic reversible hammer
A L Torque 615320 3/8” 175 139 244 1350
• Free speed: 10.000 revolutions per minute
• Max. torque: 244 Nm
• Maximum working pressure: 6.2 bar
• Air consumption: 71 l/min
• Air inlet: 1/4”
• Max. bolt size: M10
Advantages• Controlled torque
• Fast screwing
• Wide range of use
Use• Car industry
• Agricultural equipment
• Heavy industry
• Shipbuilding
• Aeronautical industry
• Larger construction machinery
• Individual mounting
How to set the rotation direction of the tool.
Important!
• Always use Unior IMPACT sockets.
1541
244 Nmart. 1541
678 Nmart. 1561
813 Nmart. 1562
1016 Nmart. 1571
1491 Nmart. 1572
2439 Nmart. 1591
2439 Nmart. 1592
3388 Nmart. 1596
4065 Nmart.1597
19
1/2” pneumatic reversible hammer
1/2” pneumatic reversible hammer
A L Torque 615321 1/2” 192 204 813 2800
A L Torque 615322 1/2” 190 188 678 2600
• Free speed: 8.000 revolution per minutes
• Max. torque: 678 Nm
• Maximum working pressure: 6.2 bar
• Air consumption: 113 l/min
• Air inlet: 1/4”
• Max. bolt size: M16
• Free speed: 7.000 revolution per minutes
• Max. torque: 813 Nm
• Maximum working pressure: 6.2 bar
• Air consumption: 119 l/min
• Air inlet: 1/4”
• Max. bolt size: M18
Max. torque [Nm]
1561 1562
20
A L Torque 615325 1” 180 495 2439 12500
A L Torque 615323 3/4” 235 220 1491 5600
3/4” pneumatic reversible hammer
1” pneumatic reversible hammer
1” pneumatic reversible hammer
1.1/2” pneumatic reversible hammer
1.1/2” pneumatic reversible hammer
A L Torque 617690 1.1/2” 145 450 3388 15800
A L Torque 617691 1.1/2” 145 465 4065 19700
• Free speed: 5.500 revolution per minutes
• Max. torque: 1.491 Nm
• Maximum woking pressure: 6.2 bar
• Air consumption: 269 l/min
• Air inlet: 3/8”
• Max. bolt size: M30
• Free speed: 4.000 revolution per minutes
• Max. torque: 2.439 Nm
• Maximum working pressure: 6.2 bar
• Air consumption: 340 l/min
• Air inlet: 1/2”
• Max. bolt size: M36
• Free speed: 4.000 revolution per minutes
• Max. torque: 2.439 Nm
• Maximum working pressure: 6.2 bar
• Air consumption: 340 l/min
• Air inlet: 1/2”
• Max. bolt size: M36
A L Torque 615326 1” 280 307 2439 10620
• Free speed: 3.000 revolution per minutes
• Max. torque: 3.388 Nm
• Maximum working pressure: 6.2 bar
• Air consumption: 410 l/min
• Air inlet: 1/2”
• Max. bolt size: M45
• Free speed: 3.000 revolution per minutes
• Max. torque: 4.065 Nm
• Maximum working pressure: 6.2 bar
• Air consumption: 453 l/min
• Air inlet: 1/2”
• Max. bolt size: M52
3/4” pneumatic reversible hammer
A L Torque 615324 3/4” 240 236 1016 4550
• Free speed: 6.500 revolution per minutes
• Max. torque: 1.016 Nm
• Maximum working pressure : 6.2 bar
• Air consumption: 198 l/min
• Air inlet: 1/4”
• Max. bolt size: M24
1571 1591
1572 1596
1592 1597
2121
Sets of stroke pneumatic hammersSets of stroke pneumatic hammersSets of stroke pneumatic hammersSets of stroke pneumatic hammersSets of stroke pneumatic hammersSets of stroke pneumatic hammersSets of stroke pneumatic hammersSets of stroke pneumatic hammersSets of stroke pneumatic hammersSets of stroke pneumatic hammersSets of stroke pneumatic hammersSets of stroke pneumatic hammers
Pneumatic ratchet and IMPACT socket set 3/8” in plastic box
615513 13
Art. Dim.
1531 37
230.4/4 75, 125
230.8/4 6-12, 13-21
230/4 6p 8, 10, 11, 12, 13, 15, 17
1374 50 ml
Pneumatic hammer and IMPACT socket set 3/8” in plastic box
615514 13
Art. Dim.
1541 175
230.4/4 75, 125
230.8/4 6-12, 13-21
230/4 6p 8, 10, 11, 12, 13, 15, 17
1374 50 ml
Pneumatic ratchet and IMPACT socket set 1/2” in plastic box
615515 12
Art. Dim.
1551 45
231.4/4 75, 125
231.8/4 10-14, 15-32
231/4 6p 10, 13, 14, 17, 19, 21, 22, 24
1374 50 ml
Pneumatic hammer and IMACT socket set 3/4”in plastic box
617161 7
Art. Dim.
1571 240
232/4 6p 19, 24, 27, 32, 36, 41
Pneumatic hammer and IMPACT socket set 1/2” in plastic box
615516 20
Art. Dim.
1561 175
231.4/4 75, 125
231.8/4 10-14, 15-32
231/4 6p 10, 13, 14, 17, 19, 21, 22, 24, 27
231/4L6p 17, 19, 21, 22, 24, 27
1374 50 ml
Stroke pneumatic hammer, with set of chisels in plastic box
619964 8
Art. Dim.
1514 170
1514 A1 182
1514 A2 180
1514 A3 180
1514 A4 180
1514 A5 190
1514 A6 178
981 PB2 307
1514PB 1555
1535 1565
1545 1575
22
Pneumatic equipmentPneumatic equipmentPneumatic equipmentPneumatic equipmentPneumatic equipmentPneumatic equipment
• Maximum working pressure: 10.9 Bar
• Air consumption: 220 l/m
• Maximum working pressure: 10.9 bar
• Air consumption: 220 l/min
Long pneumatic duster
Pneumatic duster
• Air inlet: 1/4”
• Maximum working pressure: 9.5 bar
• Air consumption: 600 l/min
• Working pressure: 0.5-8.5 bar
• Working temperature: 5-60 °C
• Filtering grade: 5µ
• Filter capacity: 15 ml
• Lubricator capacity: 25 m
• Air inlet: 3/8”
• Maximum working pressure: 9.5 bar
• Air consumption: 1.800 l/min
• Working pressure: 0,5-8,5 bar
• Working temperature: 5-60 °C
• Filtering grade: 5µ
• Filter capacity: 60 ml
• Lubricator capacity: 90 ml
Pneumatic filter regulator and lubricator 1/4”
Pressure gauge for 1501 and 1502
Pneumatic filter regulator and lubricator 3/8”
Pressure gauge for 1500
L A D 617768 420 135 6 145
L A D
617767 260 135 6 130
L A 617736 150 220 1195
L A 617735 90 155 415
• Air inlet: 1/2”
• Maximum working pressure: 9.5 bar
• Air consumption: 2.300 l/min
• Working pressure: 0.5-8.5 bar
• Working temperature: 5-60 °C
• Filtering grade: 5µ
• Filter capacity: 100 ml
• Lubricator capacity: 160 ml
Pneumatic filter regulator and lubricator 1/2”
L A 617737 150 220 1395
617741 20
617742 20
1508A 1500
1508B
1500PG
1501
1501PG
1502
2323
• Metal housing
• Outside thread
• Inside hole diameter ø 7 mm
• Metal housing
• Outside thread
• Inside hole diameter ø 7 mm
• Metal housing
• Outside thread
• Inside hole diameter ø 10 mm
• Outside thread
• Inside hole diameter ø 7 mm
• Outside thread
• Inside hole diameter ø 10 mm
Coupling, female part
Coupling, female part
Coupling, female part
Coupling, male part
Coupling, male part
L 617797 1/4” 14 34 18
617798 3/8” 19 36.5 28
618483 1/2” 22 39 38
L 617793 1/4” 20 58 104
617794 3/8” 20 54 94
L 617795 1/4" 20 54.5 110
617796 3/8" 20 55 102
L
621452 3/8” 24 62.5
621453 1/2” 24 65.0
621454 3/4” 27 67.1
L
621455 3/8” 17 39.4
621456 1/2” 24 39.4
621457 3/4” 27 48.5
Spiral pneumatic hose
L D 617743 1/4” 9 m 6.5 x 10 660
617744 1/4” 9 m 8 x 12 860
617745 3/8” 9 m 11 x 16 1360
617746 1/4” 12 m 6.5 x 10 830
617747 1/4” 12 m 8 x 12 1100
617748 3/8” 12 m 11 x 16 19000
• Air inlet: 3/4”
• Maximum working pressure: 9.5 bar
• Working pressure: 0.5-8.5 bar
• Working temperature: 5-60 °C
• Filtering grade: 5µ
• Filter capacity: 100 ml
• Lubricator capacity: 160 ml
• Air consumption 2500 l/min
L A 621473 150 220 1395
Pneumatic filter regulator and lubricator 3/4”
1506KZ7
1506KN7
1505
1506KZ10
1507Z7
1507Z10
1503
621515
UNIOR d.d.Kovaška cesta 10
3214 ZrečeSlovenia
T: +386 (0) 3 757 81 00F: +386 (0) 3 576 26 43
E: sales@unior.siI: www.uniortools.com
top related