Transcript
Highway Safety
Methods Adopted By
Civil Engineers
Haider Ali JafferiCivil Engineer
The main purpose of adopting safety measures for highways and road sides is:• To reduce no. of accidents,• To facilitate safer journey,• To increase the quality of transit
system,• To maintain the regular traffic flow.
Introduction:
Safe
ty
Met
hods
Ad
opte
dBy
Civ
il En
gine
er
• Cross Section• Rumble Strips• Design Of Roadside• Junctions• Linear villages• Roundabouts• Traffic calming road design• Innovative Interchange and
Intersection design• Traffic signs• Pedestrian Crossing• Barriers
The main elements of a road cross section are:
The pavement with the vehicle lanes, edge strip and markings
The emergency zone and obstacle free zone
The embankment and cutting slopes The width of the cross section is
determined by the pavement related to the number of lanes
The required width of the edge strip The shoulders and earthwork slopes
and depth
Cross section
To reduce the number and severity of roadway departure crashes, or run-off-the-road and cross center line crashes on 2-lane, rural, undivided roads.
Rumble Strips
Rumble Strips (cont)
Shoulder rumble strips: Placed on highway shoulders along the edge of the travel lane, to prevent single vehicle run-off-the-road crashes.
Center line rumble strips:
Placed on or near the center line, to prevent head-on crashes and opposite direction sideswipe crashes. They can also be helpful to prevent some crashes when a driver veers across the center line
Rumble Strips (cont)
Advantages: Alert drivers upon drifting or
deviation. The reflective paint helps to increase
visibility. Reduce the number of crashes.
Design Of Road-Side
Design of road side must comply the following essential requirements:
i. The road must be free from ditches and screeding should be done properly.
ii. Shoulders and edge strips must be provided.
iii. Super elevations must not be too steep.
Design of Road-Side (cont)iv. Avoid sharper turns.v. Emergency zones/lanes must be
provided.vi. Wider Obstacle free zones to reduce
the risk in case of road run-off accidents.
Junctions
“A road junction is a location where multiple roads intersect, allowing vehicular traffic to change from one road to another.”
Junctions (cont)
A road junction has to fulfill following requirements:
i. Visibleii. Oversee-able iii. Comprehensibleiv. Completeness
Linear Villages
“A linear village is that part of a (transit) road which lies within a built-up area.”
Passing a road from public areas must comply with the special safety needs:
i. Pedestrian Safetyii. Speed reduction measuresiv. Footpaths, side railings and
shouldersv. Avoid Sharp turns and blind corners
Originated in Europe over 35 years ago.
Intended to calm (or slow down) traffic.
Used primarily as a safety measure on low volume & low speed roadways.
Traffic calming may involve “physical changes" to the roadway that slow traffic down. Some examples:
Traffic Calming Road Design
Using innovative design interchanges & intersections to help move large volumes of traffic through limited amounts of space safely and efficiently.
Following are the main types:i. Diverging Diamond Interchange
(DDI)ii. Echelon Interchangeiii. Single Point Interchange (SPI)
Innovative Interchange and Intersection Design
Innovative Interchange and Intersection Design (Cont)i. Diverging Diamond Interchange (DDI)This innovative interchange, sometimes called a “double crossover diamond,” .
Innovative Interchange and Intersection Design (Cont)
Purpose: Increase capacity Safety Decrease
congestion Minimize the cost
of new infrastructure.
Advantages: Safety Greater
capacity and efficiency
Easy navigation
Suitability
Innovative Interchange and Intersection Design (Cont)
ii. Echelon InterchangeThis innovative interchange is designed to accommodate two high-volume streets. An echelon introduces a bridge, splitting traffic into two levels, creating two separated intersections of one-way streets. Because there is no opposing traffic for left turns there is more green light time for all movements.Advantages
Safety Greater capacity
and efficiency
Innovative Interchange and Intersection Design (Cont)
iii. Single Point InterchangeAll traffic is controlled by a single set of traffic signals located in the center of the intersection.
Innovative Interchange and Intersection Design (Cont)
Reasons for considering SPI: Better Safety Greater capacity and efficiency than
conventional designs Also accommodates large trucks. Ease of Navigation
Traffic Signs
Traffic signs or road signs are signs erected at the side of or above roads to give instructions or provide information to road users.
Traffic signs generally :• Control the flow of traffic• Warns about hazards ahead• Guide to destination• Informs roadway services.
Traffic signs are intentionally color coded to assist the operator.
In traffic signs, fluorescent material is used.
Various sign
boards are used, such as:
i. Stop & Yield Sign Boards
A STOP sign is a traffic sign to notify drivers to completely halt while YIELD means to slow down to at a point
ii. Warning Signs
Alerts to hazards or changing in conditions such as changes in road layout, proximity to a school zone, sharp turns etc.
iii. Guide signs
Indicates route markers, distance-and-destination signs, and informational signs.
iv. Construction & Maintenance Road Work Warnings The work areas are protected from
traffic by orange (or yellow) warning signs during the construction or repairing works.
Help to guide pedestrians and vehicle traffic safely through a work zone and past any hazards.
Roundabouts
“A roundabout is a type of circular intersection or junction in which road traffic flows almost continuously in one direction around a central point.”
Improved safety Due to Roundabouts
top related