Controller Programming

Relay Control

Relay Control -- Introduction

Two-position control, using a digital (relay) output, is used to turn something on and off. We use a differential and an offset to tell an output when to open and close based on the control variable and setpoint.

Relay Control -- Definitions

• Differential – amount of change in the control variable from when the output turns on to when it turns off

• Offset – a value that creates a deadband for a stage – the first stage typically has an offset of 0

Offsets and Differentials, 2 Setpoints

HeatSetpointOffset

DifferentialOutput turns OFF

Output turns ON

Offset

Differential Output turns OFF

Output turns ON

CoolSetpoint

"COOLING" or"HIGH ALARM"

"HEATING" or"LOW ALARM"

Offsets, Differentials and Deadband, 1 Setpoint

Offset

DifferentialOutput turns OFF

Output turns ON

Setpoint

Offset

Differential Output turns OFF

Output turns ON"COOLING" or"HIGH ALARM"

Deadband

"HEATING" or"LOW ALARM"

Deadband

Used

on the

SZ1025b

and

SZ1143b

Proportional Control

Proportional Control -- Introduction

Analog outputs are called modulating outputs. These outputs vary based on how far the input is away from setpoint. Modulating outputs provide tighter control than two position outputs.

Proportional Control -- Definitions

• Proportional Control – generates an output that is related to the distance between the active setpoint and the input

• Proportional Band/Throttling Range – number of degrees (or percent of span) that the input must change to drive the output from 0 to 100% (either 0 to 20 mA or 4 to 20 mA)

Proportional Control -- Definitions

• Setpoint Offset – a value that creates a deadband before modulation starts

• Aquastat – allows the action to reverse when a digital input is made (SZ1017a,

SZ1018, SZ1143b, SZ1051) or an analog input exceeds a certain value (SZ1025a, SZ1018, SZ1062, SZ1064)

Proportional Control -- Definitions

• Direct Acting – the output increases as the input increases

• Reverse Acting – the output decreases as the input increases

Direct Acting - Output 12mA @ Setpoint

Reverse Acting - Output 12mA @ Setpoint

Direct Acting - Output 4 or 20mA @ Setpoint

Cooling Heating

Reverse Acting - Output 4 or 20mA @ Setpoint

Cooling Heating

Keypad Programming

Thermostat Keypad Layout

fan

Occupied

Heating

Cooling

Fan

Service

Program/

COOLER

WARMERData

switch

systemswitch

programsetup

clocksetup

servicestatus

SZ1060 Series Keypad Layout

fan

Occupied

Heating

Cooling

Fan

Service

Program/

COOLER

WARMERData

switch

systemswitch

programsetup

clocksetup

servicestatus

Comparison of Thermostat Keypads

Typical Superstat™ Keypad SZ1060 Series Keypad

SL1001a & SZ1140 Series Keypad Layout

SCROLL

NEXT

UP

DOWN

Conventional Thermostats

• Menu-by-Menu Example– Follow Along Using Demo Panel– Slides Printed in Handout– Catalog Page 183

• All Thermostats Basically the Same

• Complete Sequences in Product Manuals

• All Sequences in Product Catalog

• www.tcsbasys.com

SZ-QD Trainer Demo Panel (SZ1031)

MON 01- 01- 97

72F12:00 AM

ENTER ACCESS

000CODE

programsetup

programsetup

248 always works!!!

Use down arrow to get to 248 more quickly.

SZ-QD Trainer Demo Panel (SZ1031) -- continued

SET ADDRESS:

000

SET BAUD RATE:

TEMPS SHOWN IN:

9.6K

FAHRENHEIT

programsetup

programsetup

programsetup

Use your badge number as the address

for your stat.

SZ-QD Trainer Demo Panel (SZ1031) -- continued

USER ACCESS TO

SET SYSTEM

MODE: AUTO

SYSTEM MODE?YES

programsetup

programsetup

SZ-QD Trainer Demo Panel (SZ1031) -- continued

USER ACCESS TOFAN MODE? YES

SET OCCUP IED FAN

MODE: ON

programsetup

programsetup

SET UNOCCUP IED

FAN MODE: AUTO

programsetup

SZ-QD Trainer Demo Panel (SZ1031) -- continued

This Screen is Repeated for

Occupied Periods B, C, and D

This Screen is Repeated for

Occupied Periods B, C, and D

SZ-QD Trainer Demo Panel (SZ1031) -- continued

UNOCCUP IED COOL

SETPOINT: 80F

programsetup

LIMIT SETPOINT

5FADJ UST +/-:

SET OVERRIDE

TIME: 180 MINUTES

programsetup

programsetup

Model Specific Features – SZ1035

ENABLE 3 HEAT &

3 COOL? YES

ENABLE STAGE 3 &

4 AS? HEAT

programsetup

programsetup

Additional Model Specific Features -- continued

ENABLE SECOND

STAGE HEAT? YES

ENABLE SECOND

STAGE COOL? YES

programsetup

programsetup

ENABLE THIRD

COOLSTAGE AS:

programsetup

ENABLE THIRD

COOLSTAGE AS:

programsetup

SZ-QD Trainer Demo Panel (SZ1031) -- continued

HEAT STAGE 1

2F

HEAT STAGE 1

OFFSET:

DIFF:

0F

HEAT STAGE 2

OFFSET: 2F

HEAT STAGE 2

2FDIFF:

programsetup

programsetup

programsetup

programsetup

HEAT STAGE 1

1F

HEAT STAGE 1

OFFSET:

DIFF:

0F

HEAT STAGE 2

OFFSET: 1F

HEAT STAGE 2

1FDIFF:

programsetup

programsetup

programsetup

programsetup

SZ-QD Trainer Demo Panel (SZ1031) -- continued

COOL STAGE 1

2F

COOL STAGE 1

OFFSET:

DIFF:

0F

programsetup

programsetup

COOL STAGE 1

1F

COOL STAGE 1OFFSET:

DIFF:

0F

programsetup

programsetup

COOL STAGE 2

OFFSET: 2F

programsetup

COOL STAGE 2

OFFSET: 1F

programsetup

SZ-QD Trainer Demo Panel (SZ1031) -- continued

COOL STAGE 2

2FDIFF:

programsetup

COOL STAGE 2

1FDIFF:

programsetup

COOL STAGE 3

OFFSET: 2F

COOL STAGE 3

DIFF: 1F

programsetup

programsetup

programsetup

programsetup

SZ-QD Trainer Demo Panel (SZ1031) -- continued

SZ-QD Trainer Demo Panel (SZ1031) -- continued

SZ-QD Trainer Demo Panel (SZ1031) -- continued

COOLING LOCKOUT

TEMP : 60F

HEATING LOCKOUT

TEMP : 70F

programsetup

programsetup

DI1 USED FOR:

FAN PROVING

programsetup

SZ-QD Trainer Demo Panel (SZ1031) -- continued

DI3 USED FOR:

FILTER SERVICE

programs e t u p

program

s e t u p

DI2 USED FOR:

SERVICE

SET DI2 SETP OINT

SHIFT: 02F

programsetup

SZ-QD Trainer Demo Panel (SZ1031) -- continued

DELAY ON POWERUP

60 SECONDS

ENABLE SMART

YESRECOVERY?

REQUIRE CODE FOR

P R OG R AMMING? YES

programs e tu p

program

s e t u p

programsetup

SZ-QD Trainer Demo Panel (SZ1031) -- continued

REQUIRE CODE FORYESCLOCK/ SCHED?

SET ACCESS

CODE: 000

MON 01- 01- 97

72F12:00 AM

programsetup

programsetup

NOTE:This is a secondary

access code.

Setting the Clock & Schedule (SZ1031)

248 always works!!!

Use down arrow to get to 248 more quickly.

Setting the Clock & Schedule (SZ1031) -- continued

This Screen is Repeated for

Occupied Periods C and D

Setting the Clock & Schedule (SZ1031) -- continued

These Screens are Repeated for Wed.,

Thurs., Fri., Sat., Sun., Plus

Holiday #1 & #2.

This Screen is Repeated for

Occupied Periods C and D

Setting the Clock & Schedule (SZ1031)-- continued

Total Possible Holidays

2 x 12 x 99 = 2,376scheds. instances days days .

Setting the Clock & Schedule (SZ1031)-- continued

Where to Get Help or Answers

• Instructions Sent with Product

• TCS Basys Controls Catalog

• Training & Reference Manual

• www.tcsbasys.com

• Call TCS Directly – 800-288-9383

Software Programming

PC Based Software -- Revelation Professional

• Menu Driven Programming• Use for Network Setup & Testing, Commissioning,

& Load Balancing• “Read” Before Making Changes• “Write” Before Going to NEXT Menu• “Write” vs. “Write Half / Write Page”• “Load All” & “Save All” Options

*** NOT SUPPORTED AS OF JAN 2009 ***

Superstat™ – conventional heat/cool…

Rev Pro Manual pg C-9

Superstat™ – conventional heat/cool…

Rev Pro Manual pg C-9

Superstat™ – conventional heat/cool…

Rev Pro Manual pg C-9

PC Based Software -- Insight

Similar to Revelation Professional…

• Tab Driven Interface

• Uses Same Datasheets as Ubiquity

• Use for Network Setup & Testing, Commissioning, & Load Balancing

• Shows Current Values (no “read” required)

• “Write Page” Before Going to New Tab

*** NEW SOLUTION AS OF JAN 2009 ***

Superstat™ – heat pump…

Superstat™ – heat pump…

Superstat™ – heat pump…

Superstat™ – heat pump…

Superstat™ – heat pump…

Superstat™ – heat pump…

Internet Style Software – Ubiquity

Similar to Revelation Professional…

• Single Page for All Programming Info• Shows Current Values (no “read” required)

• Writes All Values on “Submit”• “Read Controller” Option (if needed)

Single Page Programming Screen

General Info, Alarms, & Assigned Assets

Schedule

Controller Summary & Ubiquity Functions

System and Setpoints & Digital Inputs

Digital Outputs

Additional Functions, Comments & Buttons

Superstat™ – heat pump…SZ1033

Superstat™ with 1 analog output…SZ1017a

Superstat™ with 1 analog output…SZ1041

Superstat™ with 2 analog outputs…SZ1051

Superstat™ with 2 analog outputs…SZ1053

General Purpose Controller…SZ1143b

General Purpose Controller…SZ1143b - cont’d

General Purpose Monitor…SZ1145

General Purpose Monitor…SZ1145 - cont’d

General Purpose Monitor…SZ1145 - cont’d

VAV Box Controller…SZ1025b

VAV Box Controller…SZ1025b - cont’d

VAV Box Controller…SZ1025b - cont’d

2 Channel, 365-Day Time Clock…SL1001a

2 Ch., 365-Day Time Clock…SL1001a - cont’d

Where to Get Help or Answers

• Instructions Sent with Product

• TCS Basys Controls Catalog

• Training & Reference Manual

• www.tcsbasys.com

• Call TCS Directly – 800-288-9383

Controll r C re i ing