Condition Monitoring of Subsea Equipment for Enhanced Equipment and Production Performance

Image Area

Condition Monitoring of Subsea Equipment for Enhanced Equipment and Production Performance

Tomi EntabanSabah Oil & Gas Conference & Exhibition

26th May 2014

2

Contents

Introduction– Multiphase Flowmeters– Subsea Boosting

FRIEND® Concept Monitoring Methodology Operational Experience FRIEND® Applications Summary

Contents

Introduction

4

Introduction – Multiphase Flowmeters

Well / production monitoring Production optimization

Gas lift and ESP

Allocation metering Flow Assurance Immediate detection of water/gas breakthrough Calibration of reservoir models Material balance Mapping remaining reserves Reservoir monitoring

Water/gas breakthrough

Introduction –Multiphase Flowmeters

5

OneSubsea™ has a focused and proven portfolio of subsea multiphase meters and measurement systems:

PhaseWatcher Subsea Multiphase and Wet Gas Flow Meter

Subsea sampling

Additional measurements: sand burst rate, H2S, scale identification, conductivity

Proven, accurate flow measurement of three-phase flow in all environments

Introduction – Multiphase Flowmeters

Introduction –Multiphase Flowmeters

6

Introduction – Multiphase Flowmeters

15,000 psi rated: tested, approved and in operation

3500 m / 11,500 ft water depth rated

205º C / 400º F rated

Introduction –Multiphase Flowmeters

7

Introduction – Subsea Boosting

Enables production from remote locations/deepwater fields Kick off dead wells Accelerate production and

extend production plateau Increase recovery by lowering well head pressure Overcome static height and header frictional losses Stabilize flow conditions in flowlines Combine high and low pressure reservoir in single flowline Flexibility and ease of installation and operation

Introduction – Subsea Boosting

8

Up to 300,000 bpd (~ 2000 m3/hr) Differential pressure 30 – 200 bar (~3000

psi) GVF up to 95% (0-100% Mechanical)

Pressure rating up to 13,500psi Water depth to 3000m Shaft power rating 300 – 3000 kW

Height ~ 5m Weight 7 – 20 metric tons < 4m2 foot print

Introduction – Subsea Boosting

Introduction – Subsea Boosting

9

Mot

or S

ectio

nP

ump

Sec

tion

Impeller Diffuser

Introduction – Subsea Boosting

Introduction – Subsea Boosting

HELICO-AXIAL Pump design

Oil submerged electric motor Integrated flow homogenizer

FRIEND® Concept

11

FRIEND® Concept - Objectives

Facilitate 24/7 Remote Expert Assistance

Increase Equipment availability Improve Lifespan of Subsea

Equipment Support Intervention Campaigns Improve Communication and

Collaboration w/ Operators Enhance production performance

FRIEND® Concept

12

FRIEND® Concept - Services

FRIEND® Concept

Portal with online tools

24/7 Support

Expert reporting

Condition Monitoring

Updated documentation

Product improvement

Alarms and notifications

Performance Monitoring

TM

13

FRIEND® Concept - Data Collection

FRIEND® Concept

Control System

24/7 Support Alerts, Reports & Revised Documentation Equipment Storage & Logistics Maintenance Information Live Process Displays & Trending

Collaboration Workspace

Web Server

Historian

Calculation Engine Secure Access

14

FRIEND® Concept - Monitored Equipment

Pumps & Subsea Process Systems17 |12 more on the way

Multiphase Metering Systems84 | 33 more on the way

Swivels & Marine Systems2 | 2 more on the way

Subsea Trees & Production SystemsNew service offering!

15

FRIEND® Concept - Statistics

FRIEND® Concept

The availability of the FRIEND service has been 99.82 % since the startup in 2006

FRIEND has proven to be an important tool in pursuing a preventive maintenance philosophy and promoting collaboration with client personnel and experts

16

FRIEND® Concept - Typical Monitored Parameters

Vx Multiphase Meter

–Differential Pressure

–Pressure

–Temperature

–Nuclear Count Rates

FRIEND® Concept

17

FRIEND® Concept - Typical Monitored Parameters

Pump Operation–Electrical Parameters–Suction Pressure–Discharge Pressure–Choke Position

Barrier Fluid System–Consumption–Temperature & Pressure–Tank Level

Control Fluid System–Consumption–Function Pressures–Valve Operations

VSD–Electrical Parameters–Pump Speed

FRIEND® Concept

18

FRIEND® Concept – Live Pump Process Display

FRIEND® Concept

19

FRIEND® Concept – Site Dashboard

FRIEND® Concept

20

FRIEND® Concept – Vx Dashboard

FRIEND® Concept

21

FRIEND® Concept – Vx Solution Triangle

FRIEND® Concept

22

FRIEND® Concept – Vx OPI

FRIEND® Concept

Monitoring Methodology

24

Monitoring Methodology

Best Practice

Operation

Adapt Operation to Individual Fields

Highlight Critical Aspects to Maintain Pump Availability

Practice 24/7 Proactive Philosophy

Category ACategory BCategory C

Condition

Establish Baseline Signature

Evaluate PossibleFailure Modes

Categorize FailureModes by Severity

Automate Detection of Failure Modes

Signature

Category ACategory BCategory C

Predictive Models

Analysis

Analyze Process Transients

Flow Assurance Mitigation Actions

Recommend Changes to Operational Procedures

Initiate Offline Expert Studies

FRIEND® Monitoring Methodology

Actions

Customer

One Subsea

Recommendations

OneSubsea

Operational Experience

26

Operational Experience

Operational Experience

Excellent relationship with client, OneSubsea always updated.

Planned maintenance/upgrade of equipment done in minimum time.

Reduced operating and maintenance costs.

Optimal use of the equipment (configuration).

27

Operational Experience - Corrective Sequence

Operational Experience

ObservationHigh variations in both suction pressure and pump power consumption

ActionRecommended the Customer to open the recirculation choke

28

Operational Experience - Corrective Sequence

Operational Experience

ObservationA drop in barrier pressure during a flowline pressure test caused negative seal dP towards process

ActionCalled the Operators, and recommended bleeding off the flowline pressure

29

Operational Experience - Corrective Sequence

Operational Experience

ObservationDiverging temperature readings from two neighbouring transmitters, which if left unattended will reach HH and trip the pump in 2-3 months

ActionInform Customer & Agree on Solutions

FRIEND® Applications

31

FRIEND® Applications - Trending Tools

FRIEND® Applications

32

FRIEND® Applications - Equipment Operational Envelope

FRIEND® Applications

33

FRIEND® Applications - Operational Performance Indicator (OPI)

Monitoring operational health.

Highlight information to identify

suboptimal conditions.

Status indicators for continuous

operational improvement.

Metrics to measure performance.

Utilize expert experience.

FRIEND® Applications

34

FRIEND® Applications - Monthly Status Report / Review

Status of the delivered equipment, as seen from an equipment vendor’s perspective.

Evaluation of condition and performance Recommendations / Areas of Concern Actual data from the field used as input List of ongoing work (reports, studies,

status of ongoing work orders, repair jobs, site work)

Commercial details (progress reporting on open PO’s)

FRIEND® Applications

35

The Way Forward

OneSubsea Alignment–Knowledge Base System

–Equipment Reliability Classification

–Further Footprint Analysis

–Enhanced Condition Based Maintenance

Cross-functional Decision-making Real-time Flow Assurance

Management–Applications

–Offline Studies

–Reporting

Summary

Summary

37

Main Goal: Increased Availability of the Equipment

Summary

Summary

7 years experience with real-time data

We perform equipment integrity monitoring and performance evaluation

Real-time data allows for effective 24/7 proactive service approach

This integrated working methodology has greatly improved the working relationship with Customer

!

Thank You for Your Attention

Tomi.Entaban@OneSubsea.com