1 E D C 2 3 4 B A 1 2 3 4 UNIVERSITY OF SOUTH CAROLINA MECHANICAL RENOVATIONS SOUTH TOWER 5 6 7 E SHEET: SHEET TITLE: DRAWN BY: D REV. DRAWING: DESCRIPTION 03/15/12 DATE: PROJECT TITLE: C CHECKED BY: DATE ORIG. BY DRAWN BY 5 6 Facsimile: (803) 791-0830 B SEAL SEAL Swygert & Associates C O N S U L T I N G E N G I N E E R S Post Office Box 11686 DBA Swygert & Assoc. Ltd. A Telephone: (803) 791-9300 Columbia, S.C. 29211 [email protected] 7 STATE PROJECT NUMBER H27-6082-NA THIS DRAWING AND THE DESIGN THEREON ARE THE PROPERTY OF SWYGERT & ASSOCIATES, LTD. THE REPRODUCTION, COPYING, OR USE OF THIS DRAWING WITHOUT THE WRITTEN CONSENT OF SWYGERT & ASSOCIATES IS PROHIBITED AND ANY INFRINGEMENT WILL BE SUBJECT TO LEGAL ACTION. BID DOCUMENTS UP BASEMENT S101 ELEV EV03 1 1 1 2 8 8 CONSTRUCTION PHASING LINE. PHASE B CONSTRUCTION AREA AREA NOT TO BE DISTURBED BY CONSTRUCTION PHASE A CONSTRUCTION AREA, LIMITED SCOPE IN PHASE B, SEE ALL NOTES DEMOLITION - TO BE NOTED ON DEMO PLANS ONLY EXISTING TEXTURE CEILING (ASBESTOS) REMOVE EXISTING WALL. REMOVE EXISTING DOOR AND FRAME. REMOVE EXISTING PARTIAL CHASE WALL AS INDICATED TO ALLOW FOR REMOVAL OF EXISTING DUCTWORK AND INSTALLATION OF NEW MECHANICAL SYSTEMS. SEE MECHANICAL FOR ADDITIONAL SCOPE AND DETAILS. REMOVE EXISTING DRYER VENT CONSTRUCTION AND PREPARE FOR NEW DRYER VENT/WALL INFILL CONSTRUCTION. SEE MECHANICAL DRAWINGS FOR SCOPE AND DETAILS. COORDINATE WITH MEP FOR FULL SCOPE OF DEMOLITION/CONSTRUCTION IN ELECTRICAL ROOMS AND PIPE CHASES AND MECHANICAL CHASE. REMOVE ALL FLOORING AND BASE TO CONCRETE SLAB IN TYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION 010000 - SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD -BASED PAINT INVESTIGATION REPORT. SAND AND PREPARE ALL WALLS FOR PAINT/PRIMER IN TYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION 010000 - SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT. REMOVE EXISTING CHAIN LINK FENCE AND GATE COMPLETELY. SEE REFLECTED CEILING DEMOLITION PLANS AND RELFECTED CEILING PLANS FOR PHASE A SCOPE IN THIS AREA. 1 2 3 4 5 6 7 8 9 REMOVE EXISTING RUBBER BASE AND VCT INSTALLED IN PHASE A IN TYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18. PREPARE CONCRETE FOR CARPET INSTALLATION REMOVE EXISTING FAN COIL UNITS AND WOODEN BASE, SEE MEP FOR FULL SCOPE OF DETAILS. REMOVE SELECTIVE BASE AND FLOORING TO CONCRETE DECK AROUND EXISTING RESIDENT ROOM FAN COIL UNITS AND VANITIES TO NEAREST FULL TILE, 2'-4" MIN. PREPARE CONCRETE FOR NEW FLOORING INSTALLATION. SEE FINISH SCHEDULE AND PLANS FOR EXTENT. REMOVE BASE AND FLOORING TO CONCRETE DECK AND PREPARE CONCRETE FOR NEW FLOORING INSTALLATION. EXISTING VCT TO REMAIN UNDER EXISTING CABINETS, CUT AT PERIMETER OF BASE CABINETS. REMOVE EXISTING DRAWER BANK, MIRROR, BACK WOOD WALL PARTITION AND ASSOCIATED CHASE UTILITIES AS NOTED ON MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS. PROTECT ADJACENT CASEWORK AND TRANSITE CURTAINWALL PANEL. SEE SPEC. SECTION 010000 - SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT. REMOVE PARTIAL EXISTING CONCRETE SLAB. SEE MECHANICAL AND STRUCTURAL FOR FULL SCOPE OF DEMOLITION AND DETAILS. REMOVE EXISTING WALL. A B C D E F G 1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE B HAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALL SEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A. 2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE. 3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGS PROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARE TO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION. 4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TO COMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE- CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO. 5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FOR REQUIRED UTILITY ROUTING. 6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK. 7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION ARE IDENTIFIED WITHIN THE SPECIFICATIONS. 8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED IN DEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGED AREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NO ADDITIONAL COST TO THE OWNER. 9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPET ON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVE DEMOLITION. 10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURING THE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS. 11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION. 12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION. 1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE B HAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALL SEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A. 2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE. 3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGS PROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARE TO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION. 4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TO COMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE- CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO. 5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FOR REQUIRED UTILITY ROUTING. 6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK. 7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION ARE IDENTIFIED WITHIN THE SPECIFICATIONS. 8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED IN DEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGED AREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NO ADDITIONAL COST TO THE OWNER. 9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPET ON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVE DEMOLITION. 10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURING THE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS. 11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION. 12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION. N PHASE A WORK - NOTE TO CONTRACTORS: 1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR. 2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTER THE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHER PARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THE GYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTS ASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING. PHASE B WORK - NOTE TO CONTRACTORS: 1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHER MATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THE PARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THE CEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTS ASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING. 2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEW PARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILL BE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR. REFERENCED ON: 1/4" = 1'-0" D1.00 1 BASEMENT DEMOLITION PLAN LEGEND PHASE A - TYPICAL DEMOLITION PLAN KEYNOTES PHASE B - TYPICAL DEMOLITION PLAN KEYNOTES PHASE A - GENERAL DEMOLITION PLAN NOTES PHASE B - GENERAL DEMOLITION PLAN NOTES D1.00 BASEMENT DEMOLITION PLAN RMB SAL
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
UP
BASEMENTS101
ELEVEV03
11
1
2
8
8
CONSTRUCTION PHASING LINE.
PHASE B CONSTRUCTION AREA
AREA NOT TO BE DISTURBED BYCONSTRUCTION
PHASE A CONSTRUCTION AREA, LIMITEDSCOPE IN PHASE B, SEE ALL NOTES
DEMOLITION - TO BE NOTED ONDEMO PLANS ONLY
EXISTING TEXTURE CEILING(ASBESTOS)
REMOVE EXISTING WALL.
REMOVE EXISTING DOOR AND FRAME.
REMOVE EXISTING PARTIAL CHASE WALL AS INDICATED TO ALLOW FORREMOVAL OF EXISTING DUCTWORK AND INSTALLATION OF NEW MECHANICALSYSTEMS. SEE MECHANICAL FOR ADDITIONAL SCOPE AND DETAILS.
REMOVE EXISTING DRYER VENT CONSTRUCTION AND PREPARE FOR NEWDRYER VENT/WALL INFILL CONSTRUCTION. SEE MECHANICAL DRAWINGS FORSCOPE AND DETAILS.
COORDINATE WITH MEP FOR FULL SCOPE OF DEMOLITION/CONSTRUCTION INELECTRICAL ROOMS AND PIPE CHASES AND MECHANICAL CHASE.
REMOVE ALL FLOORING AND BASE TO CONCRETE SLAB IN TYPICALCORRIDORS HFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION010000 - SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOSINVESTIGATION REPORT/LEAD -BASED PAINT INVESTIGATION REPORT.
SAND AND PREPARE ALL WALLS FOR PAINT/PRIMER IN TYPICAL CORRIDORSHFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION 010000 -SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOS INVESTIGATIONREPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING CHAIN LINK FENCE AND GATE COMPLETELY.
SEE REFLECTED CEILING DEMOLITION PLANS AND RELFECTED CEILING PLANSFOR PHASE A SCOPE IN THIS AREA.
1
2
3
4
5
6
7
8
9
REMOVE EXISTING RUBBER BASE AND VCT INSTALLED IN PHASE A INTYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18.PREPARE CONCRETE FOR CARPET INSTALLATION
REMOVE EXISTING FAN COIL UNITS AND WOODEN BASE, SEE MEP FORFULL SCOPE OF DETAILS.
REMOVE SELECTIVE BASE AND FLOORING TO CONCRETE DECKAROUND EXISTING RESIDENT ROOM FAN COIL UNITS AND VANITIES TONEAREST FULL TILE, 2'-4" MIN. PREPARE CONCRETE FOR NEWFLOORING INSTALLATION. SEE FINISH SCHEDULE AND PLANS FOREXTENT.
REMOVE BASE AND FLOORING TO CONCRETE DECK AND PREPARECONCRETE FOR NEW FLOORING INSTALLATION. EXISTING VCT TOREMAIN UNDER EXISTING CABINETS, CUT AT PERIMETER OF BASECABINETS.
REMOVE EXISTING DRAWER BANK, MIRROR, BACK WOOD WALLPARTITION AND ASSOCIATED CHASE UTILITIES AS NOTED ONMECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS. PROTECTADJACENT CASEWORK AND TRANSITE CURTAINWALL PANEL. SEESPEC. SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
REMOVE PARTIAL EXISTING CONCRETE SLAB. SEE MECHANICAL ANDSTRUCTURAL FOR FULL SCOPE OF DEMOLITION AND DETAILS.
REMOVE EXISTING WALL.
A
B
C
D
E
F
G
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENTWALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALSOR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED ORALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITIONAND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGSPROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARETO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OFPHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ONTHIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FORREQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONALITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDINGDATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION AREIDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NOADDITIONAL COST TO THE OWNER.9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPETON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVEDEMOLITION.10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURINGTHE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BEPROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WEREFOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENTWALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALSOR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED ORALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITIONAND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGSPROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARETO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OFPHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ONTHIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FORREQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONALITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDINGDATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION AREIDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NOADDITIONAL COST TO THE OWNER.9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPETON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVEDEMOLITION.10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURINGTHE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BEPROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WEREFOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.
N
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
REFERENCED ON: 1/4" = 1'-0"D1.001 BASEMENT DEMOLITION PLAN
LEGEND
PHASE A - TYPICAL DEMOLITION PLAN KEYNOTES
PHASE B - TYPICAL DEMOLITION PLAN KEYNOTES
PHASE A - GENERAL DEMOLITION PLAN NOTES
PHASE B - GENERAL DEMOLITION PLAN NOTES
D1.00
BASE
MENT
DEMO
LITIO
N PL
AN
RMB
SAL
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
UP
DN
UP
TRASH002A
TRASH002
VENDING001
OFFICE012A
CUST.012
STORAGE011
CUST.009
LAUNDRY007
TLT008
TLT006
LAUNDRY007A
BEDROOM005
LIVING003
CHASE004
HALLH004
HALLH003
HALLH002
HALLH005
HALLH001
ELEC010
STAIRST01
OPENTOBELOW
PANTRY003B
MECH003A
ELEVEV01
ELEVEV02
3
4
5
5
5
EVEV03
CONSTRUCTION PHASING LINE.
PHASE B CONSTRUCTION AREA
AREA NOT TO BE DISTURBED BYCONSTRUCTION
PHASE A CONSTRUCTION AREA, LIMITEDSCOPE IN PHASE B, SEE ALL NOTES
DEMOLITION - TO BE NOTED ONDEMO PLANS ONLY
EXISTING TEXTURE CEILING(ASBESTOS)
REMOVE EXISTING RUBBER BASE AND VCT INSTALLED IN PHASE A INTYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18.PREPARE CONCRETE FOR CARPET INSTALLATION
REMOVE EXISTING FAN COIL UNITS AND WOODEN BASE, SEE MEP FORFULL SCOPE OF DETAILS.
REMOVE SELECTIVE BASE AND FLOORING TO CONCRETE DECKAROUND EXISTING RESIDENT ROOM FAN COIL UNITS AND VANITIES TONEAREST FULL TILE, 2'-4" MIN. PREPARE CONCRETE FOR NEWFLOORING INSTALLATION. SEE FINISH SCHEDULE AND PLANS FOREXTENT.
REMOVE BASE AND FLOORING TO CONCRETE DECK AND PREPARECONCRETE FOR NEW FLOORING INSTALLATION. EXISTING VCT TOREMAIN UNDER EXISTING CABINETS, CUT AT PERIMETER OF BASECABINETS.
REMOVE EXISTING DRAWER BANK, MIRROR, BACK WOOD WALLPARTITION AND ASSOCIATED CHASE UTILITIES AS NOTED ONMECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS. PROTECTADJACENT CASEWORK AND TRANSITE CURTAINWALL PANEL. SEESPEC. SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
REMOVE PARTIAL EXISTING CONCRETE SLAB. SEE MECHANICAL ANDSTRUCTURAL FOR FULL SCOPE OF DEMOLITION AND DETAILS.
REMOVE EXISTING WALL.
A
B
C
D
E
F
G
REMOVE EXISTING WALL.
REMOVE EXISTING DOOR AND FRAME.
REMOVE EXISTING PARTIAL CHASE WALL AS INDICATED TO ALLOW FORREMOVAL OF EXISTING DUCTWORK AND INSTALLATION OF NEW MECHANICALSYSTEMS. SEE MECHANICAL FOR ADDITIONAL SCOPE AND DETAILS.
REMOVE EXISTING DRYER VENT CONSTRUCTION AND PREPARE FOR NEWDRYER VENT/WALL INFILL CONSTRUCTION. SEE MECHANICAL DRAWINGS FORSCOPE AND DETAILS.
COORDINATE WITH MEP FOR FULL SCOPE OF DEMOLITION/CONSTRUCTION INELECTRICAL ROOMS AND PIPE CHASES AND MECHANICAL CHASE.
REMOVE ALL FLOORING AND BASE TO CONCRETE SLAB IN TYPICALCORRIDORS HFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION010000 - SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOSINVESTIGATION REPORT/LEAD -BASED PAINT INVESTIGATION REPORT.
SAND AND PREPARE ALL WALLS FOR PAINT/PRIMER IN TYPICAL CORRIDORSHFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION 010000 -SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOS INVESTIGATIONREPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING CHAIN LINK FENCE AND GATE COMPLETELY.
SEE REFLECTED CEILING DEMOLITION PLANS AND RELFECTED CEILING PLANSFOR PHASE A SCOPE IN THIS AREA.
1
2
3
4
5
6
7
8
9
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENTWALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALSOR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED ORALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITIONAND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGSPROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARETO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OFPHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ONTHIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FORREQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONALITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDINGDATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION AREIDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NOADDITIONAL COST TO THE OWNER.9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPETON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVEDEMOLITION.10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURINGTHE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BEPROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WEREFOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENTWALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALSOR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED ORALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITIONAND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGSPROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARETO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OFPHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ONTHIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FORREQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONALITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDINGDATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION AREIDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NOADDITIONAL COST TO THE OWNER.9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPETON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVEDEMOLITION.10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURINGTHE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BEPROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WEREFOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.
N
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
REFERENCED ON: 1/4" = 1'-0"D1.011 GROUND LEVEL DEMOLITION PLAN
LEGEND
PHASE B - TYPICAL DEMOLITION PLAN KEYNOTES
PHASE A - TYPICAL DEMOLITION PLAN KEYNOTESPHASE A - GENERAL DEMOLITION PLAN NOTES
PHASE B - GENERAL DEMOLITION PLAN NOTES
D1.01
GROU
ND LE
VEL
DEMO
LITIO
NPL
AN
RMB
SAL
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
DN
UP
UP
DN
VESTIBULEV101
VESTIBULEV102
HALLH101
RA KITCHEN103D
RA LIVING103
RA BEDROOM103A
OFFICE102
CLST103C
TLT103B
MEN105CUST
104
CHASE104A
ELEC106
STUDY107
LOBBY101
COVEREDENTRY
3
cpt
cptcpt
cptcpt
cpt
5
5
5
5
CONSTRUCTION PHASING LINE.
PHASE B CONSTRUCTION AREA
AREA NOT TO BE DISTURBED BYCONSTRUCTION
PHASE A CONSTRUCTION AREA, LIMITEDSCOPE IN PHASE B, SEE ALL NOTES
DEMOLITION - TO BE NOTED ONDEMO PLANS ONLY
EXISTING TEXTURE CEILING(ASBESTOS)
REMOVE EXISTING WALL.
REMOVE EXISTING DOOR AND FRAME.
REMOVE EXISTING PARTIAL CHASE WALL AS INDICATED TO ALLOW FORREMOVAL OF EXISTING DUCTWORK AND INSTALLATION OF NEW MECHANICALSYSTEMS. SEE MECHANICAL FOR ADDITIONAL SCOPE AND DETAILS.
REMOVE EXISTING DRYER VENT CONSTRUCTION AND PREPARE FOR NEWDRYER VENT/WALL INFILL CONSTRUCTION. SEE MECHANICAL DRAWINGS FORSCOPE AND DETAILS.
COORDINATE WITH MEP FOR FULL SCOPE OF DEMOLITION/CONSTRUCTION INELECTRICAL ROOMS AND PIPE CHASES AND MECHANICAL CHASE.
REMOVE ALL FLOORING AND BASE TO CONCRETE SLAB IN TYPICALCORRIDORS HFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION010000 - SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOSINVESTIGATION REPORT/LEAD -BASED PAINT INVESTIGATION REPORT.
SAND AND PREPARE ALL WALLS FOR PAINT/PRIMER IN TYPICAL CORRIDORSHFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION 010000 -SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOS INVESTIGATIONREPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING CHAIN LINK FENCE AND GATE COMPLETELY.
SEE REFLECTED CEILING DEMOLITION PLANS AND RELFECTED CEILING PLANSFOR PHASE A SCOPE IN THIS AREA.
1
2
3
4
5
6
7
8
9
REMOVE EXISTING RUBBER BASE AND VCT INSTALLED IN PHASE A INTYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18.PREPARE CONCRETE FOR CARPET INSTALLATION
REMOVE EXISTING FAN COIL UNITS AND WOODEN BASE, SEE MEP FORFULL SCOPE OF DETAILS.
REMOVE SELECTIVE BASE AND FLOORING TO CONCRETE DECKAROUND EXISTING RESIDENT ROOM FAN COIL UNITS AND VANITIES TONEAREST FULL TILE, 2'-4" MIN. PREPARE CONCRETE FOR NEWFLOORING INSTALLATION. SEE FINISH SCHEDULE AND PLANS FOREXTENT.
REMOVE BASE AND FLOORING TO CONCRETE DECK AND PREPARECONCRETE FOR NEW FLOORING INSTALLATION. EXISTING VCT TOREMAIN UNDER EXISTING CABINETS, CUT AT PERIMETER OF BASECABINETS.
REMOVE EXISTING DRAWER BANK, MIRROR, BACK WOOD WALLPARTITION AND ASSOCIATED CHASE UTILITIES AS NOTED ONMECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS. PROTECTADJACENT CASEWORK AND TRANSITE CURTAINWALL PANEL. SEESPEC. SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
REMOVE PARTIAL EXISTING CONCRETE SLAB. SEE MECHANICAL ANDSTRUCTURAL FOR FULL SCOPE OF DEMOLITION AND DETAILS.
REMOVE EXISTING WALL.
A
B
C
D
E
F
G
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENTWALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALSOR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED ORALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITIONAND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGSPROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARETO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OFPHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ONTHIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FORREQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONALITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDINGDATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION AREIDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NOADDITIONAL COST TO THE OWNER.9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPETON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVEDEMOLITION.10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURINGTHE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BEPROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WEREFOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENTWALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALSOR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED ORALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITIONAND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGSPROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARETO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OFPHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ONTHIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FORREQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONALITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDINGDATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION AREIDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NOADDITIONAL COST TO THE OWNER.9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPETON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVEDEMOLITION.10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURINGTHE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BEPROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WEREFOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.
N
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
REFERENCED ON: 1/4" = 1'-0"D1.11 FIRST FLOOR DEMOLITION PLAN
LEGEND
PHASE A - TYPICAL DEMOLITION PLAN KEYNOTES
PHASE B - TYPICAL DEMOLITION PLAN KEYNOTES
PHASE A - GENERAL DEMOLITION PLAN NOTES
PHASE B - GENERAL DEMOLITION PLAN NOTES
D1.1
FIRS
T FL
OOR
DEMO
LITIO
N PL
AN
RMB
SAL
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
UP
UPDN
DN
A3.13
1
A3.2
B
C
D
EE
EB
C
B
C
B
C
B
C
B
B
C
B
C
B
C
B
C
B
C
B
C
B
C
C
B
E E EE
E
E EE
E
EEE
E
F
G
F
6
6
6
5
5
7
7
7 A
A
A
5
A3.2
A3.23
A3.15
RESIDENTFL#08
RESIDENTFL#09
RESIDENTFL#10
RESIDENTFL#11
RESIDENTFL#12
COMMUNITYFL#13
RESIDENTFL#00
RESIDENTFL#01
RESIDENTFL#02
RESIDENTFL#03
RESIDENTFL#04
RESIDENTFL#05
RESIDENTFL#06
RESIDENTFL#07
HALLHFL#01
HALLHFL#03
HALLHLF#02
CHASEFL#17
WOMENFL#15
ELECFL#16
CUSTFL#14
CONSTRUCTION PHASING LINE.
PHASE B CONSTRUCTION AREA
AREA NOT TO BE DISTURBED BYCONSTRUCTION
PHASE A CONSTRUCTION AREA, LIMITEDSCOPE IN PHASE B, SEE ALL NOTES
DEMOLITION - TO BE NOTED ONDEMO PLANS ONLY
EXISTING TEXTURE CEILING(ASBESTOS)
REMOVE EXISTING WALL.
REMOVE EXISTING DOOR AND FRAME.
REMOVE EXISTING PARTIAL CHASE WALL AS INDICATED TO ALLOW FORREMOVAL OF EXISTING DUCTWORK AND INSTALLATION OF NEW MECHANICALSYSTEMS. SEE MECHANICAL FOR ADDITIONAL SCOPE AND DETAILS.
REMOVE EXISTING DRYER VENT CONSTRUCTION AND PREPARE FOR NEWDRYER VENT/WALL INFILL CONSTRUCTION. SEE MECHANICAL DRAWINGS FORSCOPE AND DETAILS.
COORDINATE WITH MEP FOR FULL SCOPE OF DEMOLITION/CONSTRUCTION INELECTRICAL ROOMS AND PIPE CHASES AND MECHANICAL CHASE.
REMOVE ALL FLOORING AND BASE TO CONCRETE SLAB IN TYPICALCORRIDORS HFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION010000 - SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOSINVESTIGATION REPORT/LEAD -BASED PAINT INVESTIGATION REPORT.
SAND AND PREPARE ALL WALLS FOR PAINT/PRIMER IN TYPICAL CORRIDORSHFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION 010000 -SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOS INVESTIGATIONREPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING CHAIN LINK FENCE AND GATE COMPLETELY.
SEE REFLECTED CEILING DEMOLITION PLANS AND RELFECTED CEILING PLANSFOR PHASE A SCOPE IN THIS AREA.
1
2
3
4
5
6
7
8
9
REMOVE EXISTING RUBBER BASE AND VCT INSTALLED IN PHASE A INTYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18.PREPARE CONCRETE FOR CARPET INSTALLATION
REMOVE EXISTING FAN COIL UNITS AND WOODEN BASE, SEE MEP FORFULL SCOPE OF DETAILS.
REMOVE SELECTIVE BASE AND FLOORING TO CONCRETE DECKAROUND EXISTING RESIDENT ROOM FAN COIL UNITS AND VANITIES TONEAREST FULL TILE, 2'-4" MIN. PREPARE CONCRETE FOR NEWFLOORING INSTALLATION. SEE FINISH SCHEDULE AND PLANS FOREXTENT.
REMOVE BASE AND FLOORING TO CONCRETE DECK AND PREPARECONCRETE FOR NEW FLOORING INSTALLATION. EXISTING VCT TOREMAIN UNDER EXISTING CABINETS, CUT AT PERIMETER OF BASECABINETS.
REMOVE EXISTING DRAWER BANK, MIRROR, BACK WOOD WALLPARTITION AND ASSOCIATED CHASE UTILITIES AS NOTED ONMECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS. PROTECTADJACENT CASEWORK AND TRANSITE CURTAINWALL PANEL. SEESPEC. SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
REMOVE PARTIAL EXISTING CONCRETE SLAB. SEE MECHANICAL ANDSTRUCTURAL FOR FULL SCOPE OF DEMOLITION AND DETAILS.
REMOVE EXISTING WALL.
A
B
C
D
E
F
G
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENTWALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALSOR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED ORALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITIONAND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGSPROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARETO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OFPHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ONTHIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FORREQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONALITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDINGDATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION AREIDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NOADDITIONAL COST TO THE OWNER.9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPETON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVEDEMOLITION.10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURINGTHE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BEPROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WEREFOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENTWALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALSOR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED ORALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITIONAND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGSPROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARETO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OFPHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ONTHIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FORREQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONALITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDINGDATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION AREIDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NOADDITIONAL COST TO THE OWNER.9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPETON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVEDEMOLITION.10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURINGTHE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BEPROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WEREFOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.
N
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
REFERENCED ON: 1/4" = 1'-0"D1.21 TYPICAL DEMOLITION PLAN - LEVEL 2-17
LEGEND
PHASE A - TYPICAL DEMOLITION PLAN KEYNOTES
PHASE B - TYPICAL DEMOLITION PLAN KEYNOTES
PHASE A - GENERAL DEMOLITION PLAN NOTES
PHASE B - GENERAL DEMOLITION PLAN NOTES
D1.2
TYPI
CAL D
EMOL
ITIO
N PL
AN,
LEVE
LS 2-
17
RMB
SAL
A NOTE TO CONTRACTORS
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
DN
DN
UP
RESIDENT1808
RESIDENT1809
RESIDENT1810
RESIDENT1811
RESIDENT1812
COMMUNITY1813
RESIDENT1801
RESIDENT1802
RESIDENT1803
RESIDENT1804
RESIDENT1805
RESIDENT1806
RESIDENT1807
HALLH1803
HALLH1801
HALLH1802
WOMEN1815
CHASE1817
ELEC1816
CUST1814
6
6
6
5
5
7
7
7 A
A
A
B
C
D
EE
EB
C
B
C
B
C
B
C
B
B
C
B
C
B
C
B
C
B
C
B
C
B
C
C
B
E E EE
E
E EE
E
EEE
E
G
G
RESIDENT1800
A3.13
1
A3.2
A3.23
A3.15
F
9
CONSTRUCTION PHASING LINE.
PHASE B CONSTRUCTION AREA
AREA NOT TO BE DISTURBED BYCONSTRUCTION
PHASE A CONSTRUCTION AREA, LIMITEDSCOPE IN PHASE B, SEE ALL NOTES
DEMOLITION - TO BE NOTED ONDEMO PLANS ONLY
EXISTING TEXTURE CEILING(ASBESTOS)
REMOVE EXISTING RUBBER BASE AND VCT INSTALLED IN PHASE A INTYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18.PREPARE CONCRETE FOR CARPET INSTALLATION
REMOVE EXISTING FAN COIL UNITS AND WOODEN BASE, SEE MEP FORFULL SCOPE OF DETAILS.
REMOVE SELECTIVE BASE AND FLOORING TO CONCRETE DECKAROUND EXISTING RESIDENT ROOM FAN COIL UNITS AND VANITIES TONEAREST FULL TILE, 2'-4" MIN. PREPARE CONCRETE FOR NEWFLOORING INSTALLATION. SEE FINISH SCHEDULE AND PLANS FOREXTENT.
REMOVE BASE AND FLOORING TO CONCRETE DECK AND PREPARECONCRETE FOR NEW FLOORING INSTALLATION. EXISTING VCT TOREMAIN UNDER EXISTING CABINETS, CUT AT PERIMETER OF BASECABINETS.
REMOVE EXISTING DRAWER BANK, MIRROR, BACK WOOD WALLPARTITION AND ASSOCIATED CHASE UTILITIES AS NOTED ONMECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS. PROTECTADJACENT CASEWORK AND TRANSITE CURTAINWALL PANEL. SEESPEC. SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
REMOVE PARTIAL EXISTING CONCRETE SLAB. SEE MECHANICAL ANDSTRUCTURAL FOR FULL SCOPE OF DEMOLITION AND DETAILS.
REMOVE EXISTING WALL.
A
B
C
D
E
F
G
REMOVE EXISTING WALL.
REMOVE EXISTING DOOR AND FRAME.
REMOVE EXISTING PARTIAL CHASE WALL AS INDICATED TO ALLOW FORREMOVAL OF EXISTING DUCTWORK AND INSTALLATION OF NEW MECHANICALSYSTEMS. SEE MECHANICAL FOR ADDITIONAL SCOPE AND DETAILS.
REMOVE EXISTING DRYER VENT CONSTRUCTION AND PREPARE FOR NEWDRYER VENT/WALL INFILL CONSTRUCTION. SEE MECHANICAL DRAWINGS FORSCOPE AND DETAILS.
COORDINATE WITH MEP FOR FULL SCOPE OF DEMOLITION/CONSTRUCTION INELECTRICAL ROOMS AND PIPE CHASES AND MECHANICAL CHASE.
REMOVE ALL FLOORING AND BASE TO CONCRETE SLAB IN TYPICALCORRIDORS HFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION010000 - SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOSINVESTIGATION REPORT/LEAD -BASED PAINT INVESTIGATION REPORT.
SAND AND PREPARE ALL WALLS FOR PAINT/PRIMER IN TYPICAL CORRIDORSHFL#01, HFL#02, AND HFL#03 ON FLOORS 2-18. SEE SPEC SECTION 010000 -SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOS INVESTIGATIONREPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING CHAIN LINK FENCE AND GATE COMPLETELY.
SEE REFLECTED CEILING DEMOLITION PLANS AND RELFECTED CEILING PLANSFOR PHASE A SCOPE IN THIS AREA.
1
2
3
4
5
6
7
8
9
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENTWALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALSOR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED ORALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITIONAND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGSPROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARETO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OFPHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ONTHIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FORREQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONALITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDINGDATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION AREIDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NOADDITIONAL COST TO THE OWNER.9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPETON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVEDEMOLITION.10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURINGTHE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BEPROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WEREFOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENTWALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALSOR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWN TO BE REMOVED ORALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITIONAND NEW WORK. INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGSPROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARETO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OFPHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ONTHIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FORREQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONALITEMS TO REMAIN AND BE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDINGDATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION AREIDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NOADDITIONAL COST TO THE OWNER.9. PROTECT ALL FLOORING TO REMAIN, INCLUDING BUT NOT LIMITED TO CARPETON FIRST FLOOR AND BASEMENT. SEE SPEC SECTION -17300 - SELECTIVEDEMOLITION.10. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURINGTHE DEMOLITION AND CONSTRUCTION PERIOD. ELEVATORS SHOULD BEPROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WEREFOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.11. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.12. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES.KEYNOTES REFERRING TO FINISHES ARE FOR PHASING CLARIFICATION.
N
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
REFERENCED ON: 1/4" = 1'-0"D1.31 18TH FLOOR DEMOLITION PLAN
LEGEND
PHASE B - TYPICAL DEMOLITION PLAN KEYNOTES
PHASE A - TYPICAL DEMOLITION PLAN KEYNOTESPHASE A - GENERAL DEMOLITION PLAN NOTES
PHASE B - GENERAL DEMOLITION PLAN NOTES
D1.3
18TH
FLO
ORDE
MOLIT
ION
PLAN
RMB
SAL
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
DN
UP
DN
2
2
2
2
COMM.1901
ELEV SHAFT1902
1
1
1
1
3
4
5
5
5
5
6
6
7
7
8
10
11
10
11
10
11
1011
13 1314
15
15
16
17
1818 18
18181818
18
11
A3.2
3' - 0
"
19 19
9A
12
12
12
12
1
ELEV EQUIP1903
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BE DISTURBED DURING PHASE A TOPREVENT PHASE B HAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALL SEPARATING PHASE A AND PHASE B IS NOT TO BEDISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOTSHOWN TO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THEEXISTING DRAWINGS PROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARE TO VERIFY EXISTING CONDITIONSPRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TO COMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TODOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICALDRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUTCONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION ARE IDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED IN DEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OF DAMAGEDAREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NO ADDITIONAL COST TO THE OWNER.9. PROVIDE AND INSTALL ALL SHORING AND SUPPORT SYSTEMS NECESSARY TO ENSURE EXISTING STRUCTURE TO REMAIN IS STABLETHROUGHOUT DEMOLITION AND CONSTRUCTION.10. ALL DEMOLITION REQUIRED FOR FUTURE INSTALLATION OF MECHANICAL CHASES TO BE COORDINATED WITH MECHANICAL DRAWINGS,EQUIPMENT SPECIFICATIONS, AND STRUCTURAL DRAWINGS.11. PROTECT EXISTING CONCRETE STRUCTURE TO REMAIN THROUGHOUT DEMOLITION/CONSTRUCTION.12. SEE STRUCTURAL DRAWINGS FOR ADDITIONAL INFORMATION REGARDING THE AREAS OF THE EXISTING CONCRETE ROOF STRUCTUREAND CONSTRUCTION TO BE REMOVED.13.CONTRACTOR TO MARK IN FIELD ALL CONCRETE STRUCTURAL ELEMENTS TO BE DEMOLISHED AND REVIEW WITH ARCHITECT PRIOR TOCOMMENCEMENT OF WORK.14. EXISTING ROOF SYSTEM INCLUDING FLASHING, COPING, AND ALL OTHER ROOFING MATERIALS TO BE REMOVED DOWN TO THE CONCRETEFRAME. PREPARE EXISTING ROOF SLAB FOR INSTALLATION OF NEW ROOF SYSTEM - SEE ROOF DETAILS FOR ADDITIONAL INFORMATION.15. SEE PHASE B - GENERAL DEMOLITION ROOF NOTES AND SHEET A1.4 FOR PHASE B ROOF SCOPE.16. SEE MECHANICAL, PLUMBING, ELECTRICAL AND STRUCTURAL FOR EXTENT OF ROOF DEMOLITION IN PHASE B.
EXISTING ROOF SYSTEM INCLUDING FLASHING, COPING, AND ALL OTHERROOFING MATERIALS TO BE REMOVED DOWN TO THE CONCRETE FRAME.PREPARE EXISTING ROOF SLAB FOR INSTALLATION OF NEW ROOF. SEE ROOFDETAILS FOR ADDITIONAL INFORMATION.
REMOVE EXISTING ROOF DRAINS. MAINTAIN/PROTECT EXISTING ROOF DRAINPIPING TO BE CONNECTED TO NEW ROOF DRAINS. SEE PLUMBING DRAWINGSFOR NEW ROOF DRAIN DETAILS.
TEMPORARILY DISCONNECT AND RELOCATE EXISTING MECHANICAL UNIT FORINSTALLATION OF NEW ROOF. SEE MECHANICAL FOR DETAILS.
REMOVE/PROTECT/STORE PARTIAL METAL STAIR TO ALLOW FOR NEW ROOFWORK.
REMOVE EXISTING PLASTIC DOWNSPOUT SPLASHBLOCK.
CUT AND CAP FLUSH WITH CONCRETE ROOF DECK MISC. ABANDONED ROOFPENETRATIONS TO BE ROOFED OVER. COORDINATE ALL LOCATIONS WITHMECHANICAL, ELECTRICAL, AND PLUMBING.
REMOVE EXISTING CONCRETE ROOF CURBS, SEE STRUCTURAL.
REMOVE PARTIAL EXISTING CONCRETE PARAPET WALL BRACE. SEESTRUCTURAL.
REMOVE PARTIAL ROOF DECK FOR INSTALLATION OF NEW MECHANICAL CHASES.COORDINATE WITH MECHANICAL, EQUIPMENT SPEC., AND STRUCTURAL.
CORE DRILL EXISTING CONCRETE WALL BASE AND INSTALL NEW OVERFLOWSCUPPER. SEE DETAILS 14/A3.2 & 15/A3.2.
1
2
3
4
5
6
7
8
9
10
REMOVE/STORE/PROTECT/AND REINSTALL EXISTING PARAPET WALL LOVERS TOALLOW ACCESS TO EXTERIOR SIDE OF WALL FOR OVERFLOW SCUPPERINSTALLATION.
REMOVE EXISTING GUTTER AND ASSOCIATED DOWNSPOUTS.
EXISTING CONCRETE CURBS TO REMAIN.
EXISTING SPIGOT TO REMAIN.
EXISTING PIPE SLEEVES TO REMAIN, SEE MECHANICAL.
EXISTING PLUMBING VENTS TO REMAIN.
EXISTING EXHAUST FAN CURB TO REMAIN. EXHAUST FAN TO REMAIN IN SERVICEAFTER PHASE A, SEE MECHANICAL.
EXISTING CONCRETE COLUMN AND OVERHEAD BRACE TO REMAIN.
REMOVE 3'-0" OF EXISTING CONCRETE ROOF CURB AND REMOVE ENTIRE METALCOPING, SEE STRUCTURAL. RECAP ENTIRE CURB WITH METAL COPING TOMATCH EXISTING THAT WAS REMOVED.
11
12
13
14
15
16
17
18
19
1. SEE LEGEND FOR GENERAL PHASING INDICATIONS. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BE DISTURBEDDURING PHASE A TO PREVENT PHASE B HAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALS OR OTHER SUSPECTED HAZARDOUSMATERIALS NOT SHOWN TO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITION AND NEW WORK. INFORMATION SHOWN ISBASED ON THE EXISTING DRAWINGS PROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARE TOVERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TO COMMENCEMENT OF DEMOLITION/RENOVATION/NEWWORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITH ELECTRONIC COPIES OF PHOTOGRAPHSAND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING,AND ELECTRICAL DRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONAL ITEMS TO REMAIN AND BE PROTECTEDTHROUGHOUT CONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. ITEMS TO BE SALVAGED AND REMOVED BY OWNER PRIOR TO DEMOLITION ARE IDENTIFIED WITHIN THE SPECIFICATIONS.8. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED IN DEMOLITION/CONSTRUCTION WORK. REPAIR OR REPLACEMENT OFDAMAGED AREAS NOT IN THE SCOPE OF WORK, SHALL BE INCLUDED IN THE WORK , WITH NO ADDITIONAL COST TO THEOWNER.9. PROTECT NEW ROOF SYSTEM INSTALLED IN PHASE A THROUGHOUT PHASE B. COORDINATE WITH MECHANICAL FORADDITIONAL PHASE B ROOF SCOPE.10. SEE MECHANICAL, PLUMBING, ELECTRICAL AND STRUCTURAL FOR EXTENT OF ROOF DEMOLITION IN PHASE B.
N
REMOVE EXHAUST FAN COMPLETE. ROOF CURB AND EXHASUTDUCT TO REMAIN. SEE MECHANICAL
A
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
REFERENCED ON: 1/4" = 1'-0"D1.41 ROOF DEMOLITION PLAN
REFERENCED ON: 1/4" = 1'-0"D1.43 PENTHOUSE DEMOLITION ROOF PLAN
REFERENCED ON: 1/4" = 1'-0"D1.42 PENTHOUSE DEMOLITION FLOOR PLAN
PHASE A - GENERAL DEMOLITION ROOF NOTES PHASE A - DEMOLITION ROOF PLAN KEYNOTES PHASE B - GENERAL DEMOLITION ROOF NOTES
D1.4
ROOF
DEM
OLIT
ION
PLAN
RMB
SAL
PHASE B - DEMOLITION ROOF PLAN KEYNOTES
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
EXPOSED STRUCTURE
OPEN TO ABOVE
OPEN TO ABOVE
OPEN TO ABOVE
SLOPED
OPEN TO ABOVE
EXPOSED STRUCTURE
EXPOSED STRUCTURE
EXPOSED STRUCTURE
16' - 8"
CONSTRUCTION PHASING LINE.
PHASE B CONSTRUCTION AREA
AREA NOT TO BE DISTURBED BYCONSTRUCTION
PHASE A CONSTRUCTION AREA, LIMITEDSCOPE IN PHASE B, SEE ALL NOTES
DEMOLITION - TO BE NOTED ONDEMO PLANS ONLY
EXISTING TEXTURE CEILING(ASBESTOS)
REMOVE EXISTING CEILING TILE,CEILING GRID AND LIGHTS. EXISTINGCEILING GRID ANGLES AT GWB, PLASTER, AND METAL EDGE SOFFITSTO REMAIN, AND TO BE REUSED FOR NEW CEILING INSTALLATION.SEE ELECTRICAL FOR ADDITIONAL DETAILS.
METAL EDGE SOFFIT TO REMAIN. PROTECT DURING DEMOLITION ANDCONSTRUCTION. SAND AND REMOVE RUST AND SCALING. PREPAREFOR NEW PAINT.
REMOVE EXISTING CEILING GRID AND LIGHTS. SEE ELECTRICAL FORADDITIONAL DETAILS. CEILING GRID WALL ANGLE TO REMAIN ATTYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18, TOBE REUSED FOR FUTURE NEW CEILING INSTALLATION.
REMOVE/ABATE SPRAY-ON TEXTURED CEILING ABOVE EXISTING LAY-IN CEILING. SEE SPECS SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
REMOVE EXISTING GWB CEILING AND LIGHTS. SEE ELECTRICAL FORADDITIONAL DETAILS.
CUT OPENING IN EXISTING ROOF DECK AS PART OF PHASE A. SEEA2.3 KEYNOTES FOR SOFFIT TO BE BUILT IN PHASE A TO ENCLOSEROOF DECK OPENING. PARTIALLY SCRAPE/ABATE EXISTINGASBESTOS CONTAINING SPRAY TEXTURE CEILING TO ALLOW FORTEMORARY SOFFIT ENCLOSURE. EXISTING CHASE WALL TO REMAINDURING PHASE A.
REMOVAL OF EXISTING GRILL, WHERE OCCURS, AND PATCHING OFSHEETROCK TO BE COMPLETED BY OTHERS. G.C. TO PAINT.
1
2
4
3
5
6
7
SELECTIVE REMOVAL OF TEXTURED CEILING IN ORDER TO ALLOWFOR INSTALLATION OF STEEL ANGLES,DUCTWORK, PIPING, ANDASSOCIATED HANGING DEVICES. SEE MECHANICAL, ELECTRICAL,PLUMBING AND SPEC. SECTION 010000 - SPECIAL CONDITIONSAND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING METAL SOFFIT. SEE MECHANICAL, ELECTRICAL,PLUMBING FOR ADDITIONAL SCOPE TO BE REMOVED. MAINTAINEXISTING SOFFIT CEILING ANGLE CONNECTION TO BE REUSED.SEE SPEC. SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
EXISTING LIGHT TO BE REMOVED AND STORED FOR REINSTALLIONDURING THIS SCOPE OF WORK. CONTRACTOR TO VERIFY ALLLIGHTS ARE WORKING PRIOR TO REMOVAL AND REPORT TOOWNER/ARCHITECT ANY FIXTURES THAT ARE NOT WORKING. SEEELECTRICAL FOR FULL SCOPE OF WORK AND COORDIATION OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID ANDALTERNATE NO. 1.
REMOVE EXISTING METAL SOFFIT. SEE MECHANICAL, ELECTRICAL,PLUMBING FOR ADDITIONAL SCOPE TO BE REMOVED. REMOVEEXISTING SOFFIT CEILING ANGLE AND PREPARE CEILING TO BEEXPOSED FOR NEW TEXTURED SPRAY MATERIAL. SEE REFLECTEDCEILING PLAN AND SPEC. SECTION 010000 - SPECIAL CONDITIONSAND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING METAL SOFFIT AND CEILING ANGLECOMPLETELY.
REMOVE EXISTING LIGHT. SEE ELECTRICAL FOR FULL SCOPE OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID ANDALTERNATE NO. 1.
REMOVE /ABATE SPRAY-ON TEXTURED CEILING COMPLETELY ANDPREPARE FOR NEW SKIM COAT CEILING FINISH AS SHOWN ONREFLECTED CEILNG PLAN, SEE SPECS. SEE SPEC SECTION010000 SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOSINVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATIONREPORT.
SELECTIVE REMOVAL OF APC CEILING TILE ONLY INSTALLED INPHASE A TO ALLOW FOR REMOVAL OF PIPING, SEE PLUMBING.PROTECT EXISTING CEILING TILE, GRID AND AND ADJACENTCEILING MATERIALS AND REINSTALL CEILING TILE AFTERREMOVAL OF PHASE B PLUMBING SCOPE IS COMPLETE.
SELECTIVE PATCHING OF EXISTING GWB BY OTHERS, SEEMECHANICAL.
SELECTIVE REMOVAL OF APC CEILING TILE ONLY INSTALLED INPHASE A TO ALLOW FOR REQUIRED MECHANICAL, ELECTRICALAND PLUMBING CONNECTIONS. PROTECT EXISTING CEILING TILE,GRID AND AND ADJACENT CEILING MATERIALS AND REINSTALLCEILING TILE AFTER REMOVAL OF PHASE B PLUMBING SCOPE ISCOMPLETE.
A
B
C
D
E
F
G
H
J
K
1. SEE LEGEND. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BEDISTURBED DURING PHASE A TO PREVENT PHASE B HAZARDOUSMATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURINGPHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAININGMATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOTSHOWN TO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OFDEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THEEXISTING DRAWINGS PROVIDED BY THE OWNER. GENERALCONTRACTOR AND SUB-CONTRACTORS ARE TO VERIFY EXISTINGCONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TODOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECTWITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOTSHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICALDRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FORADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUTCONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS,PIPES AND DUCTWORK.7. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION SCOPE. REPAIR OR REPLACEMENT OFDAMAGED AREAS NOT IN THIS SCOPE SHALL BE INCLUDED IN THE WORK,WITH NO ADDITIONAL COST TO THE OWNER.8. ELECTRICAL CONTRACTOR IS TO VERIFY ALL CEILING MOUNTEDELECTRICAL DEVICES ARE IN WORKING CONDITION AT COMMENCEMENTOF DEMOLITION/CONSTRUCTION. SEE ELECTRICAL DRAWINGS ANDSPECS FOR ALL SCOPE RELATED TO CEILING MOUNTED DEVICES PRIORTO COMMENCEMENT OF DEMOLITION/CONSTRUCTION.9. ALL EXISTING WALL SCONCES/LIGHTING TO REMAIN UNLESS NOTEDOTHERWISE.10. ALL CEILING LIGHTING TO REMAIN UNLESS NOTED OTHERWISE.11. SEE ELECTRICAL FOR FULL SCOPE AND COORDINATION OF LIGHTINGDEMOLITION/CONSTRUCTION FOR BASE BID AND ALTERNATE NO. 1.12. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BEUSED DURING THE DEMOLITION AND CONSTRUCTION PERIOD.ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THECONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOBPHASE. SEE SPECIFICATIONS.13. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OFFINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASINGCLARIFICATION.
1. SEE LEGEND. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BEDISTURBED DURING PHASE A TO PREVENT PHASE B HAZARDOUSMATERIALS FROM BEING DISTURBED. THE BOUNDARY WALL SEPARATINGPHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAININGMATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWNTO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OFDEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THEEXISTING DRAWINGS PROVIDED BY THE OWNER. GENERAL CONTRACTORAND SUB-CONTRACTORS ARE TO VERIFY EXISTING CONDITIONS PRIOR TOBID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TODOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECTWITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOTSHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICALDRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FORADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUTCONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS, PIPESAND DUCTWORK.7. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION SCOPE. REPAIR OR REPLACEMENT OFDAMAGED AREAS NOT IN THIS SCOPE SHALL BE INCLUDED IN THE WORK,WITH NO ADDITIONAL COST TO THE OWNER.8. ELECTRICAL CONTRACTOR IS TO VERIFY ALL CEILING MOUNTEDELECTRICAL DEVICES ARE IN WORKING CONDITION AT COMMENCEMENTOF DEMOLITION/CONSTRUCTION. SEE ELECTRICAL DRAWINGS AND SPECSFOR ALL SCOPE RELATED TO CEILING MOUNTED DEVICES PRIOR TOCOMMENCEMENT OF DEMOLITION/CONSTRUCTION.9. ALL EXISTING WALL SCONCES/LIGHTING TO REMAIN UNLESS NOTEDOTHERWISE.10. ALL CEILING LIGHTING TO REMAIN UNLESS NOTED OTHERWISE. SEEELECTRICAL FOR FULL SCOPE OF LIGHTING DEMOLITION/CONSTRUCTION.11. COORDINATE PARTIAL/SELECTIVE REMOVAL OF APC CEILING TOALLOW FOR MECHANICAL, PLUMBING AND ELECTRICAL CONNECTIONSREQUIRED IN PHASE B SCOPE. PROTECT EXISTING CEILING TILE AND GRID(INSTALLED IN PHASE A) AND REINSTALL AFTER REQUIRED CONNECTIONSHAVE BEEN MADE. ALL CEILING TILES DAMAGED DURING CONSTRUCTIONSHALL BE REPLACE BY CONTRACTOR AT NO ADDITIONAL COST TOOWNER. SEE MECHANICAL, ELECTRICAL AND PLUMBING DRAWINGS FORFULL SCOPE OF WORK.12. SEE ELECTRICAL DRAWINGS FOR FULL SCOPE AND COORDINATION OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID AND ALTERNATENO. 1.13. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BEUSED DURING THE DEMOLITION AND CONSTRUCTION PERIOD.ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THECONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOBPHASE. SEE SPECIFICATIONS.14. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OFFINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASINGCLARIFICATION.
N
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
REFERENCED ON: 1/4" = 1'-0"D2.001 BASEMENT DEMOLITION REFLECTED CEILING PLAN
LEGEND
PHASE A - DEMO REFLECTED CEILING PLAN KEYNOTES
PHASE B - DEMO REFLECTED CEILING PLAN KEYNOTES
PHASE A - GENERAL DEMOLITION RCP NOTES
PHASE B- GENERAL DEMOLITION RCP NOTES
D2.00
BASE
MENT
DEMO
LITIO
N RE
FLEC
TED
CEILI
NG P
LAN
RMB
SAL
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
9' - 11"
8' - 5"
8' - 4"
8' - 11 1/2"8' - 11 1/2"
9' - 11"
OPEN TO ABOVE
OPEN TO ABOVE
OPEN TO ABOVE
EXPOSED STRUCTURE
EXPOSEDSTRUCTURE
EXPOSED STRUCTURE
EXPOSEDSTRUCTURE
EXPOSED STRUCTURE
8' - 2"
8' - 0"
8' - 5 3/4"
8' - 0"
OPEN TO ABOVE
NO ACCESSTO FIELD VERIFY
EXPOSED STRUCTURE
13' - 8"
13' - 8"
EXPOSED STRUCTURE
13' - 8"
13' - 8"
13' - 8"
13' - 8"
13' - 8"EXPOSEDSTRUCTURE
13' - 8"
OFFICE012A
CUST.012
STORAGE011
CUST.009
HALLH005
LAUNDRY007TLT
008
ELEC010
STAIRST01
CHASE004
TLT006
LAUNDRY007A
HALLH004
BEDROOM005
MECH003A
PANTRY003B
LIVING003
HALLH002
HALLH001
TRASH002
TRASH002A
VENDING001
HALLH003
ELEVEV01
ELEVEV02
11
1
1
1
1 1
1
1
1
1
1
1
1
CONSTRUCTION PHASING LINE.
PHASE B CONSTRUCTION AREA
AREA NOT TO BE DISTURBED BYCONSTRUCTION
PHASE A CONSTRUCTION AREA, LIMITEDSCOPE IN PHASE B, SEE ALL NOTES
DEMOLITION - TO BE NOTED ONDEMO PLANS ONLY
EXISTING TEXTURE CEILING(ASBESTOS)
SELECTIVE REMOVAL OF TEXTURED CEILING IN ORDER TO ALLOWFOR INSTALLATION OF STEEL ANGLES,DUCTWORK, PIPING, ANDASSOCIATED HANGING DEVICES. SEE MECHANICAL, ELECTRICAL,PLUMBING AND SPEC. SECTION 010000 - SPECIAL CONDITIONSAND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING METAL SOFFIT. SEE MECHANICAL, ELECTRICAL,PLUMBING FOR ADDITIONAL SCOPE TO BE REMOVED. MAINTAINEXISTING SOFFIT CEILING ANGLE CONNECTION TO BE REUSED.SEE SPEC. SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
EXISTING LIGHT TO BE REMOVED AND STORED FOR REINSTALLIONDURING THIS SCOPE OF WORK. CONTRACTOR TO VERIFY ALLLIGHTS ARE WORKING PRIOR TO REMOVAL AND REPORT TOOWNER/ARCHITECT ANY FIXTURES THAT ARE NOT WORKING. SEEELECTRICAL FOR FULL SCOPE OF WORK AND COORDIATION OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID ANDALTERNATE NO. 1.
REMOVE EXISTING METAL SOFFIT. SEE MECHANICAL, ELECTRICAL,PLUMBING FOR ADDITIONAL SCOPE TO BE REMOVED. REMOVEEXISTING SOFFIT CEILING ANGLE AND PREPARE CEILING TO BEEXPOSED FOR NEW TEXTURED SPRAY MATERIAL. SEE REFLECTEDCEILING PLAN AND SPEC. SECTION 010000 - SPECIAL CONDITIONSAND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING METAL SOFFIT AND CEILING ANGLECOMPLETELY.
REMOVE EXISTING LIGHT. SEE ELECTRICAL FOR FULL SCOPE OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID ANDALTERNATE NO. 1.
REMOVE /ABATE SPRAY-ON TEXTURED CEILING COMPLETELY ANDPREPARE FOR NEW SKIM COAT CEILING FINISH AS SHOWN ONREFLECTED CEILNG PLAN, SEE SPECS. SEE SPEC SECTION010000 SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOSINVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATIONREPORT.
SELECTIVE REMOVAL OF APC CEILING TILE ONLY INSTALLED INPHASE A TO ALLOW FOR REMOVAL OF PIPING, SEE PLUMBING.PROTECT EXISTING CEILING TILE, GRID AND AND ADJACENTCEILING MATERIALS AND REINSTALL CEILING TILE AFTERREMOVAL OF PHASE B PLUMBING SCOPE IS COMPLETE.
SELECTIVE PATCHING OF EXISTING GWB BY OTHERS, SEEMECHANICAL.
SELECTIVE REMOVAL OF APC CEILING TILE ONLY INSTALLED INPHASE A TO ALLOW FOR REQUIRED MECHANICAL, ELECTRICALAND PLUMBING CONNECTIONS. PROTECT EXISTING CEILING TILE,GRID AND AND ADJACENT CEILING MATERIALS AND REINSTALLCEILING TILE AFTER REMOVAL OF PHASE B PLUMBING SCOPE ISCOMPLETE.
A
B
C
D
E
F
G
H
J
K
REMOVE EXISTING CEILING TILE,CEILING GRID AND LIGHTS. EXISTINGCEILING GRID ANGLES AT GWB, PLASTER, AND METAL EDGE SOFFITSTO REMAIN, AND TO BE REUSED FOR NEW CEILING INSTALLATION.SEE ELECTRICAL FOR ADDITIONAL DETAILS.
METAL EDGE SOFFIT TO REMAIN. PROTECT DURING DEMOLITION ANDCONSTRUCTION. SAND AND REMOVE RUST AND SCALING. PREPAREFOR NEW PAINT.
REMOVE EXISTING CEILING GRID AND LIGHTS. SEE ELECTRICAL FORADDITIONAL DETAILS. CEILING GRID WALL ANGLE TO REMAIN ATTYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18, TOBE REUSED FOR FUTURE NEW CEILING INSTALLATION.
REMOVE/ABATE SPRAY-ON TEXTURED CEILING ABOVE EXISTING LAY-IN CEILING. SEE SPECS SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
REMOVE EXISTING GWB CEILING AND LIGHTS. SEE ELECTRICAL FORADDITIONAL DETAILS.
CUT OPENING IN EXISTING ROOF DECK AS PART OF PHASE A. SEEA2.3 KEYNOTES FOR SOFFIT TO BE BUILT IN PHASE A TO ENCLOSEROOF DECK OPENING. PARTIALLY SCRAPE/ABATE EXISTINGASBESTOS CONTAINING SPRAY TEXTURE CEILING TO ALLOW FORTEMORARY SOFFIT ENCLOSURE. EXISTING CHASE WALL TO REMAINDURING PHASE A.
REMOVAL OF EXISTING GRILL, WHERE OCCURS, AND PATCHING OFSHEETROCK TO BE COMPLETED BY OTHERS. G.C. TO PAINT.
1
2
4
3
5
6
7
1. SEE LEGEND. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BEDISTURBED DURING PHASE A TO PREVENT PHASE B HAZARDOUSMATERIALS FROM BEING DISTURBED. THE BOUNDARY WALL SEPARATINGPHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAININGMATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWNTO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OFDEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THEEXISTING DRAWINGS PROVIDED BY THE OWNER. GENERAL CONTRACTORAND SUB-CONTRACTORS ARE TO VERIFY EXISTING CONDITIONS PRIOR TOBID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TODOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECTWITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOTSHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICALDRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FORADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUTCONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS, PIPESAND DUCTWORK.7. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION SCOPE. REPAIR OR REPLACEMENT OFDAMAGED AREAS NOT IN THIS SCOPE SHALL BE INCLUDED IN THE WORK,WITH NO ADDITIONAL COST TO THE OWNER.8. ELECTRICAL CONTRACTOR IS TO VERIFY ALL CEILING MOUNTEDELECTRICAL DEVICES ARE IN WORKING CONDITION AT COMMENCEMENTOF DEMOLITION/CONSTRUCTION. SEE ELECTRICAL DRAWINGS AND SPECSFOR ALL SCOPE RELATED TO CEILING MOUNTED DEVICES PRIOR TOCOMMENCEMENT OF DEMOLITION/CONSTRUCTION.9. ALL EXISTING WALL SCONCES/LIGHTING TO REMAIN UNLESS NOTEDOTHERWISE.10. ALL CEILING LIGHTING TO REMAIN UNLESS NOTED OTHERWISE. SEEELECTRICAL FOR FULL SCOPE OF LIGHTING DEMOLITION/CONSTRUCTION.11. COORDINATE PARTIAL/SELECTIVE REMOVAL OF APC CEILING TOALLOW FOR MECHANICAL, PLUMBING AND ELECTRICAL CONNECTIONSREQUIRED IN PHASE B SCOPE. PROTECT EXISTING CEILING TILE AND GRID(INSTALLED IN PHASE A) AND REINSTALL AFTER REQUIRED CONNECTIONSHAVE BEEN MADE. ALL CEILING TILES DAMAGED DURING CONSTRUCTIONSHALL BE REPLACE BY CONTRACTOR AT NO ADDITIONAL COST TOOWNER. SEE MECHANICAL, ELECTRICAL AND PLUMBING DRAWINGS FORFULL SCOPE OF WORK.12. SEE ELECTRICAL DRAWINGS FOR FULL SCOPE AND COORDINATION OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID AND ALTERNATENO. 1.13. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BEUSED DURING THE DEMOLITION AND CONSTRUCTION PERIOD.ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THECONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOBPHASE. SEE SPECIFICATIONS.14. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OFFINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASINGCLARIFICATION.
1. SEE LEGEND. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BEDISTURBED DURING PHASE A TO PREVENT PHASE B HAZARDOUSMATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURINGPHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAININGMATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOTSHOWN TO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OFDEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THEEXISTING DRAWINGS PROVIDED BY THE OWNER. GENERALCONTRACTOR AND SUB-CONTRACTORS ARE TO VERIFY EXISTINGCONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TODOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECTWITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOTSHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICALDRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FORADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUTCONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS,PIPES AND DUCTWORK.7. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION SCOPE. REPAIR OR REPLACEMENT OFDAMAGED AREAS NOT IN THIS SCOPE SHALL BE INCLUDED IN THE WORK,WITH NO ADDITIONAL COST TO THE OWNER.8. ELECTRICAL CONTRACTOR IS TO VERIFY ALL CEILING MOUNTEDELECTRICAL DEVICES ARE IN WORKING CONDITION AT COMMENCEMENTOF DEMOLITION/CONSTRUCTION. SEE ELECTRICAL DRAWINGS ANDSPECS FOR ALL SCOPE RELATED TO CEILING MOUNTED DEVICES PRIORTO COMMENCEMENT OF DEMOLITION/CONSTRUCTION.9. ALL EXISTING WALL SCONCES/LIGHTING TO REMAIN UNLESS NOTEDOTHERWISE.10. ALL CEILING LIGHTING TO REMAIN UNLESS NOTED OTHERWISE.11. SEE ELECTRICAL FOR FULL SCOPE AND COORDINATION OF LIGHTINGDEMOLITION/CONSTRUCTION FOR BASE BID AND ALTERNATE NO. 1.12. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BEUSED DURING THE DEMOLITION AND CONSTRUCTION PERIOD.ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THECONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOBPHASE. SEE SPECIFICATIONS.13. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OFFINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASINGCLARIFICATION.
N
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
REFERENCED ON: 1/4" = 1'-0"D2.011 GROUND LEVEL DEMOLITION REFLECTED CEILING PLAN
LEGEND
PHASE B - DEMO REFLECTED CEILING PLAN KEYNOTES
PHASE A - DEMO REFLECTED CEILING PLAN KEYNOTES
PHASE B- GENERAL DEMOLITION RCP NOTES
PHASE A - GENERAL DEMOLITION RCP NOTES
D2.01
GROU
ND LE
VEL
DEMO
LITIO
NRE
FLEC
TED
CEILI
NG P
LAN
RMB
SAL
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
14'-5 1/2"EXPOSED
STRUCTURE
14' 5 1/2"EXPOSED
STRUCTURE
OPEN TO ABOVE
OPEN TO ABOVE
OPEN TO ABOVE
7'-1" CEILINGHEIGHT INELEVATOR CAB
8' - 2"
11' - 0 3/4"
12' - 5 1/4"
11' - 11 1/4"
11' - 11 1/4"
11' - 11 1/4" 8' - 2"
8' - 5 1/2"
8' - 8"
7' - 11 1/2"
11' - 11 1/2"
11' - 11 1/2"
8' - 0"8' - 0"
11' - 11"
11' - 11"
11' - 11"
EXP STRUCTURE
STUDY107
LOBBY101
VESTIBULEV101
HALLH101
VESTIBULEV102
LOBBY101
OFFICE102
RA BEDROOM103A
TLT103B
CLST103CRA LIVING
103RA KITCHEN
103D
MEN105
CHASE104A
ELEC106
CUST104
8' - 2"
11' - 11 1/2"
11' - 11 1/2"8' - 5 1/2"
12' - 0"
1
1
1
1
1
1
1
1
1
1
1
15
1
1
2
2
22
2
2
22222
H
H
H
H
H
7 7
5
CONSTRUCTION PHASING LINE.
PHASE B CONSTRUCTION AREA
AREA NOT TO BE DISTURBED BYCONSTRUCTION
PHASE A CONSTRUCTION AREA, LIMITEDSCOPE IN PHASE B, SEE ALL NOTES
DEMOLITION - TO BE NOTED ONDEMO PLANS ONLY
EXISTING TEXTURE CEILING(ASBESTOS)
SELECTIVE REMOVAL OF TEXTURED CEILING IN ORDER TO ALLOWFOR INSTALLATION OF STEEL ANGLES,DUCTWORK, PIPING, ANDASSOCIATED HANGING DEVICES. SEE MECHANICAL, ELECTRICAL,PLUMBING AND SPEC. SECTION 010000 - SPECIAL CONDITIONSAND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING METAL SOFFIT. SEE MECHANICAL, ELECTRICAL,PLUMBING FOR ADDITIONAL SCOPE TO BE REMOVED. MAINTAINEXISTING SOFFIT CEILING ANGLE CONNECTION TO BE REUSED.SEE SPEC. SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
EXISTING LIGHT TO BE REMOVED AND STORED FOR REINSTALLIONDURING THIS SCOPE OF WORK. CONTRACTOR TO VERIFY ALLLIGHTS ARE WORKING PRIOR TO REMOVAL AND REPORT TOOWNER/ARCHITECT ANY FIXTURES THAT ARE NOT WORKING. SEEELECTRICAL FOR FULL SCOPE OF WORK AND COORDIATION OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID ANDALTERNATE NO. 1.
REMOVE EXISTING METAL SOFFIT. SEE MECHANICAL, ELECTRICAL,PLUMBING FOR ADDITIONAL SCOPE TO BE REMOVED. REMOVEEXISTING SOFFIT CEILING ANGLE AND PREPARE CEILING TO BEEXPOSED FOR NEW TEXTURED SPRAY MATERIAL. SEE REFLECTEDCEILING PLAN AND SPEC. SECTION 010000 - SPECIAL CONDITIONSAND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING METAL SOFFIT AND CEILING ANGLECOMPLETELY.
REMOVE EXISTING LIGHT. SEE ELECTRICAL FOR FULL SCOPE OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID ANDALTERNATE NO. 1.
REMOVE /ABATE SPRAY-ON TEXTURED CEILING COMPLETELY ANDPREPARE FOR NEW SKIM COAT CEILING FINISH AS SHOWN ONREFLECTED CEILNG PLAN, SEE SPECS. SEE SPEC SECTION010000 SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOSINVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATIONREPORT.
SELECTIVE REMOVAL OF APC CEILING TILE ONLY INSTALLED INPHASE A TO ALLOW FOR REMOVAL OF PIPING, SEE PLUMBING.PROTECT EXISTING CEILING TILE, GRID AND AND ADJACENTCEILING MATERIALS AND REINSTALL CEILING TILE AFTERREMOVAL OF PHASE B PLUMBING SCOPE IS COMPLETE.
SELECTIVE PATCHING OF EXISTING GWB BY OTHERS, SEEMECHANICAL.
SELECTIVE REMOVAL OF APC CEILING TILE ONLY INSTALLED INPHASE A TO ALLOW FOR REQUIRED MECHANICAL, ELECTRICALAND PLUMBING CONNECTIONS. PROTECT EXISTING CEILING TILE,GRID AND AND ADJACENT CEILING MATERIALS AND REINSTALLCEILING TILE AFTER REMOVAL OF PHASE B PLUMBING SCOPE ISCOMPLETE.
A
B
C
D
E
F
G
H
J
K
REMOVE EXISTING CEILING TILE,CEILING GRID AND LIGHTS. EXISTINGCEILING GRID ANGLES AT GWB, PLASTER, AND METAL EDGE SOFFITSTO REMAIN, AND TO BE REUSED FOR NEW CEILING INSTALLATION.SEE ELECTRICAL FOR ADDITIONAL DETAILS.
METAL EDGE SOFFIT TO REMAIN. PROTECT DURING DEMOLITION ANDCONSTRUCTION. SAND AND REMOVE RUST AND SCALING. PREPAREFOR NEW PAINT.
REMOVE EXISTING CEILING GRID AND LIGHTS. SEE ELECTRICAL FORADDITIONAL DETAILS. CEILING GRID WALL ANGLE TO REMAIN ATTYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18, TOBE REUSED FOR FUTURE NEW CEILING INSTALLATION.
REMOVE/ABATE SPRAY-ON TEXTURED CEILING ABOVE EXISTING LAY-IN CEILING. SEE SPECS SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
REMOVE EXISTING GWB CEILING AND LIGHTS. SEE ELECTRICAL FORADDITIONAL DETAILS.
CUT OPENING IN EXISTING ROOF DECK AS PART OF PHASE A. SEEA2.3 KEYNOTES FOR SOFFIT TO BE BUILT IN PHASE A TO ENCLOSEROOF DECK OPENING. PARTIALLY SCRAPE/ABATE EXISTINGASBESTOS CONTAINING SPRAY TEXTURE CEILING TO ALLOW FORTEMORARY SOFFIT ENCLOSURE. EXISTING CHASE WALL TO REMAINDURING PHASE A.
REMOVAL OF EXISTING GRILL, WHERE OCCURS, AND PATCHING OFSHEETROCK TO BE COMPLETED BY OTHERS. G.C. TO PAINT.
1
2
4
3
5
6
7
1. SEE LEGEND. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BEDISTURBED DURING PHASE A TO PREVENT PHASE B HAZARDOUSMATERIALS FROM BEING DISTURBED. THE BOUNDARY WALL SEPARATINGPHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAININGMATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWNTO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OFDEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THEEXISTING DRAWINGS PROVIDED BY THE OWNER. GENERAL CONTRACTORAND SUB-CONTRACTORS ARE TO VERIFY EXISTING CONDITIONS PRIOR TOBID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TODOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECTWITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOTSHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICALDRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FORADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUTCONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS, PIPESAND DUCTWORK.7. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION SCOPE. REPAIR OR REPLACEMENT OFDAMAGED AREAS NOT IN THIS SCOPE SHALL BE INCLUDED IN THE WORK,WITH NO ADDITIONAL COST TO THE OWNER.8. ELECTRICAL CONTRACTOR IS TO VERIFY ALL CEILING MOUNTEDELECTRICAL DEVICES ARE IN WORKING CONDITION AT COMMENCEMENTOF DEMOLITION/CONSTRUCTION. SEE ELECTRICAL DRAWINGS AND SPECSFOR ALL SCOPE RELATED TO CEILING MOUNTED DEVICES PRIOR TOCOMMENCEMENT OF DEMOLITION/CONSTRUCTION.9. ALL EXISTING WALL SCONCES/LIGHTING TO REMAIN UNLESS NOTEDOTHERWISE.10. ALL CEILING LIGHTING TO REMAIN UNLESS NOTED OTHERWISE. SEEELECTRICAL FOR FULL SCOPE OF LIGHTING DEMOLITION/CONSTRUCTION.11. COORDINATE PARTIAL/SELECTIVE REMOVAL OF APC CEILING TOALLOW FOR MECHANICAL, PLUMBING AND ELECTRICAL CONNECTIONSREQUIRED IN PHASE B SCOPE. PROTECT EXISTING CEILING TILE AND GRID(INSTALLED IN PHASE A) AND REINSTALL AFTER REQUIRED CONNECTIONSHAVE BEEN MADE. ALL CEILING TILES DAMAGED DURING CONSTRUCTIONSHALL BE REPLACE BY CONTRACTOR AT NO ADDITIONAL COST TOOWNER. SEE MECHANICAL, ELECTRICAL AND PLUMBING DRAWINGS FORFULL SCOPE OF WORK.12. SEE ELECTRICAL DRAWINGS FOR FULL SCOPE AND COORDINATION OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID AND ALTERNATENO. 1.13. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BEUSED DURING THE DEMOLITION AND CONSTRUCTION PERIOD.ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THECONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOBPHASE. SEE SPECIFICATIONS.14. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OFFINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASINGCLARIFICATION.
1. SEE LEGEND. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BEDISTURBED DURING PHASE A TO PREVENT PHASE B HAZARDOUSMATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURINGPHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAININGMATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOTSHOWN TO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OFDEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THEEXISTING DRAWINGS PROVIDED BY THE OWNER. GENERALCONTRACTOR AND SUB-CONTRACTORS ARE TO VERIFY EXISTINGCONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TODOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECTWITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOTSHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICALDRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FORADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUTCONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS,PIPES AND DUCTWORK.7. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION SCOPE. REPAIR OR REPLACEMENT OFDAMAGED AREAS NOT IN THIS SCOPE SHALL BE INCLUDED IN THE WORK,WITH NO ADDITIONAL COST TO THE OWNER.8. ELECTRICAL CONTRACTOR IS TO VERIFY ALL CEILING MOUNTEDELECTRICAL DEVICES ARE IN WORKING CONDITION AT COMMENCEMENTOF DEMOLITION/CONSTRUCTION. SEE ELECTRICAL DRAWINGS ANDSPECS FOR ALL SCOPE RELATED TO CEILING MOUNTED DEVICES PRIORTO COMMENCEMENT OF DEMOLITION/CONSTRUCTION.9. ALL EXISTING WALL SCONCES/LIGHTING TO REMAIN UNLESS NOTEDOTHERWISE.10. ALL CEILING LIGHTING TO REMAIN UNLESS NOTED OTHERWISE.11. SEE ELECTRICAL FOR FULL SCOPE AND COORDINATION OF LIGHTINGDEMOLITION/CONSTRUCTION FOR BASE BID AND ALTERNATE NO. 1.12. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BEUSED DURING THE DEMOLITION AND CONSTRUCTION PERIOD.ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THECONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOBPHASE. SEE SPECIFICATIONS.13. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OFFINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASINGCLARIFICATION.
N
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
REFERENCED ON: 1/4" = 1'-0"D2.11 FIRST FLOOR DEMOLITION REFLECTED CEILING PLAN
LEGEND
PHASE B - DEMO REFLECTED CEILING PLAN KEYNOTES
PHASE A - DEMO REFLECTED CEILING PLAN KEYNOTES
PHASE B- GENERAL DEMOLITION RCP NOTES
PHASE A - GENERAL DEMOLITION RCP NOTES
D2.1
FIRS
T FL
OOR
DEMO
LITIO
N RE
FLEC
TED
CEILI
NG P
LAN
RMB
SAL
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
7' - 7 1/2"
8' - 6"
7' - 7 1/2"
8' - 6" 8' - 6" 8' - 6"
8' - 6"
7' - 7 1/2"7' - 7 1/2"7' - 7 1/2"
8' - 6"
8' - 6"
7' - 7 1/2"7' - 7 1/2"
8' - 6"8' - 6"
7' - 7 1/2"7' - 7 1/2"
8' - 6"
7' - 7 1/2"
8' - 6"
8' - 6"
7' - 7"
8' - 6"
7' - 2 5/8"
7' - 2 5/8"
7' - 4"
8'-6"EXPOSED
STRUCTURE
8'-6"EXPOSED
STRUCTURE
OPEN TO ABOVE
OPEN TO ABOVE
OPEN TO ABOVE
SLOPED SLOPED
7' - 7 1/2"
SLOPED SLOPED
EXPOSEDSTRUCTURE
EXPOSEDSTRUCTURE
7' - 8"
C
3
3
3
5
A3.2
A
4
4
4
BC
B B B B
E
BBBBB
A
D
A
A
A
A
C CC
C C C CC
F
RESIDENTFL#08 RESIDENT
FL#09RESIDENT
FL#10RESIDENT
FL#11
RESIDENTFL#12
COMMUNITYFL#13
RESIDENTFL#00
RESIDENTFL#01
RESIDENTFL#02
RESIDENTFL#03
RESIDENTFL#04
RESIDENTFL#05
RESIDENTFL#06
RESIDENTFL#07
HALLHFL#01
HALLHFL#03
HALLHLF#02
CHASEFL#17
WOMENFL#15
ELECFL#16
CUSTFL#14
G
A
AAAAA
A
AA A
A
A
A
A
A
A A A
A A
A
A
A
A
A
A
J
J
K
K
K
CONSTRUCTION PHASING LINE.
PHASE B CONSTRUCTION AREA
AREA NOT TO BE DISTURBED BYCONSTRUCTION
PHASE A CONSTRUCTION AREA, LIMITEDSCOPE IN PHASE B, SEE ALL NOTES
DEMOLITION - TO BE NOTED ONDEMO PLANS ONLY
EXISTING TEXTURE CEILING(ASBESTOS)
REMOVE EXISTING CEILING TILE,CEILING GRID AND LIGHTS. EXISTINGCEILING GRID ANGLES AT GWB, PLASTER, AND METAL EDGE SOFFITSTO REMAIN, AND TO BE REUSED FOR NEW CEILING INSTALLATION.SEE ELECTRICAL FOR ADDITIONAL DETAILS.
METAL EDGE SOFFIT TO REMAIN. PROTECT DURING DEMOLITION ANDCONSTRUCTION. SAND AND REMOVE RUST AND SCALING. PREPAREFOR NEW PAINT.
REMOVE EXISTING CEILING GRID AND LIGHTS. SEE ELECTRICAL FORADDITIONAL DETAILS. CEILING GRID WALL ANGLE TO REMAIN ATTYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18, TOBE REUSED FOR FUTURE NEW CEILING INSTALLATION.
REMOVE/ABATE SPRAY-ON TEXTURED CEILING ABOVE EXISTING LAY-IN CEILING. SEE SPECS SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
REMOVE EXISTING GWB CEILING AND LIGHTS. SEE ELECTRICAL FORADDITIONAL DETAILS.
CUT OPENING IN EXISTING ROOF DECK AS PART OF PHASE A. SEEA2.3 KEYNOTES FOR SOFFIT TO BE BUILT IN PHASE A TO ENCLOSEROOF DECK OPENING. PARTIALLY SCRAPE/ABATE EXISTINGASBESTOS CONTAINING SPRAY TEXTURE CEILING TO ALLOW FORTEMORARY SOFFIT ENCLOSURE. EXISTING CHASE WALL TO REMAINDURING PHASE A.
REMOVAL OF EXISTING GRILL, WHERE OCCURS, AND PATCHING OFSHEETROCK TO BE COMPLETED BY OTHERS. G.C. TO PAINT.
1
2
4
3
5
6
7
OPEN TO ABOVE
OPEN TO ABOVE
OPEN TO ABOVE
SLOPED SLOPED
SLOPED SLOPED
EXPOSEDSTRUCTURE
EXPOSEDSTRUCTURE
8'-6"EXPOSED
STRUCTURE
8'-6"EXPOSED
STRUCTURE
8' - 6"
7' - 7 1/2" 7' - 7 1/2"
8' - 6" 8' - 6"
7' - 7 1/2" 7' - 7 1/2"
8' - 6" 8' - 6"
7' - 7 1/2"
7' - 7 1/2"
8' - 6"
8' - 6"
7' - 7 1/2"7' - 7 1/2"
8' - 6"8' - 6"
7' - 7 1/2"
8' - 6"
7' - 7 1/2"7' - 7 1/2"
8' - 6"
8' - 6"
7' - 7"
8' - 6"
7' - 2 1/4"
C
3
3
3
A
4
4
4
BC
B B B B
E
BBBBB
A
D
A
A
A
A
C CC
C C C CC
G
A
AAAAA
A
AA A
A
A
A
A
A
A A A
A A
A
A
A
A
A
A
F
8' - 6"
7' - 8"
7' - 8"
5
A3.2
J
J
K
K
K
1. SEE LEGEND. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BE DISTURBED DURING PHASE ATO PREVENT PHASE B HAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALS OR OTHERSUSPECTED HAZARDOUS MATERIALS NOT SHOW TO BE REMOVED OR ALTERED WITHIN THE PROJECTSCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITION AND NEW WORK.INFORMATION SHOWN IS BASED ON THE EXISTING DRAWINGS PROVIDED BY THE OWNER. GENERALCONTRACTOR AND SUB-CONTRACTORS ARE TO VERIFY EXISTING CONDITIONS PRIOR TO BID ANDPRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TO COMMENCEMENT OFDEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDEARCHITECT WITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ON THIS PLAN. SEEMECHANICAL, PLUMBING, AND ELECTRICAL DRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONAL ITEMS TO REMAIN ANDBE PROTECTED THROUGHOUT CONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS,PIPES AND DUCTWORK.7. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED IN DEMOLITION/CONSTRUCTION SCOPE. REPAIROR REPLACEMENT OF DAMAGED AREAS NOT IN THIS SCOPE SHALL BE INCLUDED IN THE WORK, WITHNO ADDITIONAL COST TO THE OWNER.8. ELECTRICAL CONTRACTOR IS TO VERIFY ALL CEILING MOUNTED ELECTRICAL DEVICES ARE INWORKING CONDITION AT COMMENCEMENT OF DEMOLITION/CONSTRUCTION. SEE ELECTRICALDRAWINGS AND SPECS FOR ALL SCOPE RELATED TO CEILING MOUNTED DEVICES PRIOR TOCOMMENCEMENT OF DEMOLITION/CONSTRUCTION.9. ALL EXISTING WALL SCONCES/LIGHTING TO REMAIN UNLESS NOTED OTHERWISE.10. ALL CEILING LIGHTING TO REMAIN UNLESS NOTED OTHERWISE.11. SEE ELECTRICAL FOR FULL SCOPE AND COORDINATION OF LIGHTING DEMOLITION/CONSTRUCTIONFOR BASE BID AND ALTERNATE NO. 1.12. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURING THE DEMOLITIONAND CONSTRUCTION PERIOD. ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THECONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.13. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES. KEYNOTES REFERRINGTO FINISHES ARE FOR PHASING CLARIFICATION.
1. SEE LEGEND. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BE DISTURBED DURING PHASE A TO PREVENT PHASE BHAZARDOUS MATERIALS FROM BEING DISTURBED. THE BOUNDARY WALL SEPARATING PHASE A AND PHASE B IS NOT TO BEDISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAINING MATERIALS OR OTHER SUSPECTED HAZARDOUSMATERIALS NOT SHOW TO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OF DEMOLITION AND NEW WORK. INFORMATIONSHOWN IS BASED ON THE EXISTING DRAWINGS PROVIDED BY THE OWNER. GENERAL CONTRACTOR AND SUB-CONTRACTORS ARE TO VERIFY EXISTING CONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TO COMMENCEMENT OFDEMOLITION/RENOVATION/NEW WORK TO DOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECT WITHELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOT SHOWN ON THIS PLAN. SEE MECHANICAL,PLUMBING, AND ELECTRICAL DRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FOR ADDITIONAL ITEMS TO REMAIN AND BE PROTECTEDTHROUGHOUT CONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS, PIPES AND DUCTWORK.7. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED IN DEMOLITION/CONSTRUCTION SCOPE. REPAIR OR REPLACEMENTOF DAMAGED AREAS NOT IN THIS SCOPE SHALL BE INCLUDED IN THE WORK, WITH NO ADDITIONAL COST TO THE OWNER.8. ELECTRICAL CONTRACTOR IS TO VERIFY ALL CEILING MOUNTED ELECTRICAL DEVICES ARE IN WORKING CONDITION ATCOMMENCEMENT OF DEMOLITION/CONSTRUCTION. SEE ELECTRICAL DRAWINGS AND SPECS FOR ALL SCOPE RELATED TOCEILING MOUNTED DEVICES PRIOR TO COMMENCEMENT OF DEMOLITION/CONSTRUCTION.9. ALL EXISTING WALL SCONCES/LIGHTING TO REMAIN UNLESS NOTED OTHERWISE.10. ALL CEILING LIGHTING TO REMAIN UNLESS NOTED OTHERWISE. SEE ELECTRICAL FOR FULL SCOPE OF LIGHTINGDEMOLITION/CONSTRUCTION.11. COORDINATE PARTIAL/SELECTIVE REMOVAL OF APC CEILING TO ALLOW FOR MECHANICAL, PLUMBING ANDELECTRICAL CONNECTIONS REQUIRED IN PHASE B SCOPE. PROTECT EXISTING CEILING TILE AND GRID (INSTALLED INPHASE A) AND REINSTALL AFTER REQUIRED CONNECTIONS HAVE BEEN MADE. ALL CEILING TILES DAMAGED DURINGCONSTRUCTION SHALL BE REPLACE BY CONTRACTOR AT NO ADDITIONAL COST TO OWNER. SEE MECHANICAL, ELECTRICALAND PLUMBING DRAWINGS FOR FULL SCOPE OF WORK.12. SEE ELECTRICAL DRAWINGS FOR FULL SCOPE AND COORDINATION OF LIGHITNG DEMOLITION/CONSTRUCTION FORBASE BID AND ALTERNATE NO. 1.13. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BE USED DURING THE DEMOLITION AND CONSTRUCTIONPERIOD. ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THE CONDITION IN WHICH THEY WERE FOUNDAT THE END OF EACH JOB PHASE. SEE SPECIFICATIONS.14. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OF FINISHES. KEYNOTES REFERRING TO FINISHES ARE FORPHASING CLARIFICATION.
SELECTIVE REMOVAL OF TEXTURED CEILING IN ORDER TO ALLOW FOR INSTALLATION OF DUCTWORK, PIPING, ANDASSOCIATED HANGING DEVICES. SEE MECHANICAL, ELECTRICAL, PLUMBING AND SPEC. SECTION 010000 - SPECIALCONDITIONS AND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING METAL SOFFIT. SEE MECHANICAL, ELECTRICAL, PLUMBING FOR ADDITIONAL SCOPE TO BE REMOVED.MAINTAIN EXISTING SOFFIT CEILING ANGLE CONNECTION TO BE REUSED. SEE SPEC. SECTION 010000 - SPECIALCONDITIONS AND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
EXISTING LIGHT TO BE REMOVED AND STORED FOR REINSTALLION DURING THIS SCOPE OF WORK. CONTRACTOR TOVERIFY ALL LIGHTS ARE WORKING PRIOR TO REMOVAL AND REPORT TO OWNER/ARCHITECT ANY FIXTURES THAT ARENOT WORKING. SEE ELECTRICAL FOR FULL SCOPE OF WORK AND COORDINATION OF LIGHTINGDEMOLITION/CONSTRUCTION FOR BASE BID AND ALTERNATE NO. 1.
REMOVE EXISTING METAL SOFFIT. SEE MECHANICAL, ELECTRICAL, PLUMBING FOR ADDITIONAL SCOPE TO BE REMOVED.REMOVE EXISTING SOFFIT CEILING ANGLE AND PREPARE CEILING TO BE EXPOSED FOR NEW TEXTURED SPRAYMATERIAL. SEE REFLECTED CEILING PLAN AND SPEC. SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING METAL SOFFIT AND CEILING ANGLE COMPLETELY.
REMOVE EXISTING LIGHT. SEE ELECTRICAL FOR FULL SCOPE AND COORDINATION OF LIGHTINGDEMOLITION/CONSTRUCTION FOR BASE BID AND ALTERNATE NO. 1.
REMOVE /ABATE SPRAY-ON TEXTURED CEILING COMPLETELY AND PREPARE FOR NEW SKIM COAT CEILING FINISH ASSHOWN ON REFLECTED CEILNG PLAN, SEE SPECS. SEE SPEC SECTION 010000 SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
SELECTIVE REMOVAL OF APC CEILING TILE ONLY INSTALLED IN PHASE A TO ALLOW FOR REMOVAL OF PIPING, SEEPLUMBING. PROTECT EXISTING CEILING TILE, GRID AND AND ADJACENT CEILING MATERIALS AND REINSTALL CEILINGTILE AFTER REMOVAL OF PHASE B PLUMBING SCOPE IS COMPLETE.
SELECTIVE PATCHING OF EXISTING GWB BY OTHERS, SEE MECHANICAL.
SELECTIVE REMOVAL OF APC CEILING TILE ONLY INSTALLED IN PHASE A TO ALLOW FOR REQUIRED MECHANICAL,ELECTRICAL AND PLUMBING CONNECTIONS. PROTECT EXISTING CEILING TILE, GRID AND AND ADJACENT CEILINGMATERIALS AND REINSTALL CEILING TILE AFTER REMOVAL OF PHASE B PLUMBING SCOPE IS COMPLETE.
A
B
C
D
E
F
G
H
J
K
N
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
REFERENCED ON: 1/4" = 1'-0"D2.21 TYPICAL DEMOLITION REFLECTED CEILING PLAN - LEVELS 2-12
LEGEND PHASE A - DEMO REFLECTED CEILING PLAN KEYNOTES
REFERENCED ON: 1/4" = 1'-0"D2.22 TYPICAL DEMOLITION REFLECTED CEILING PLAN - LEVELS 13-17
D2.2
TYPI
CAL D
EMOL
ITIO
NRE
FLEC
TED
CEILI
NG P
LAN,
LEVE
LS 2-
17
RMB
SAL
PHASE A - GENERAL DEMOLITION RCP NOTES PHASE B- GENERAL DEMOLITION RCP NOTES PHASE B - DEMO REFLECTED CEILING PLAN KEYNOTES
1
ED
C
2 3 4
BA
1 2 3 4
UNIV
ERSI
TY O
F SO
UTH
CARO
LINA
MECH
ANIC
AL R
ENOV
ATIO
NSSO
UTH
TOW
ER
5 6 7
E
SHEET:
SHEE
T TI
TLE:
DRAW
N BY
:
D
REV.
DRAW
ING:
DESC
RIPT
ION
03/15
/12DA
TE:
PROJ
ECT
TITL
E:
C
CHEC
KED
BY:
DATE
ORIG
. BY
DRAW
N BY
5 6
Facsimile: (803) 791-0830
B
SEAL
SEAL
Swyg
ert &
Ass
ocia
tes
C O
N S
U L
T I
N G
E
N G
I N
E E
R S
Post Office Box 11686
DBA Swygert & Assoc. Ltd.
A
Telephone: (803) 791-9300
Columbia, S.C. 29211
mail@
swygert-associates.com
7
STAT
E PR
OJEC
T NU
MBER
H27
-608
2-NA
THIS DRAWING AND THE
DESIGN THEREON ARE THE
PROPERTY OF SW
YGERT &
ASSOCIATES, LTD. THE
REPRODUC
TION
, COPYING, OR
USE OF THIS DRAWING
WITHOU
T THE WRITTEN
CON
SENT OF SW
YGERT &
ASSOCIATES IS PROHIBITED
AND ANY INFRINGEMENT WILL
BE SUBJECT TO LEGAL ACTION
.
BID
DOCU
MENT
S
8'-7"EXPOSED
STRUCTURE
8'-7"EXPOSED
STRUCTURE
OPEN TO ABOVE
OPEN TO ABOVE
OPEN TO ABOVE
7'-1" CEILINGHEIGHT INELEVATOR CAB
8' - 6"8' - 6"8' - 6"8' - 6"8' - 6"
8' - 6"
8' - 6"
8' - 6" 8' - 6" 8' - 6" 8' - 6" 8' - 6"
8' - 6"
7' - 3"
EXPOSEDSTRUCTURE
EXPOSEDSTRUCTURE
SLOPED
SLOPED
7' - 3"
7' - 3"
7' - 2 1/4"
RESIDENT1808
HALLH1802
HALLH1801
HALLH1803
C
3
3
3
A
AC
A A A A
AAAAA
A
A
A
A
A
A
C CC
C C C CC
RESIDENT1809
RESIDENT1810
RESIDENT1811
RESIDENT1812
COMMUNITY1813
RESIDENT1801
RESIDENT1802
RESIDENT1803
RESIDENT1804
RESIDENT1805
RESIDENT1806
RESIDENT1807
WOMEN1815
CUST1814
ELEC1816
CHASE1817
RESIDENT1800
FG
A
AAAAA
A
AA A
A
A
A
A
A
A A A
A A
A
A
A
A
A
A
6
5
A3.2
K
K
K
CONSTRUCTION PHASING LINE.
PHASE B CONSTRUCTION AREA
AREA NOT TO BE DISTURBED BYCONSTRUCTION
PHASE A CONSTRUCTION AREA, LIMITEDSCOPE IN PHASE B, SEE ALL NOTES
DEMOLITION - TO BE NOTED ONDEMO PLANS ONLY
EXISTING TEXTURE CEILING(ASBESTOS)
REMOVE EXISTING CEILING TILE,CEILING GRID AND LIGHTS. EXISTINGCEILING GRID ANGLES AT GWB, PLASTER, AND METAL EDGE SOFFITSTO REMAIN, AND TO BE REUSED FOR NEW CEILING INSTALLATION.SEE ELECTRICAL FOR ADDITIONAL DETAILS.
METAL EDGE SOFFIT TO REMAIN. PROTECT DURING DEMOLITION ANDCONSTRUCTION. SAND AND REMOVE RUST AND SCALING. PREPAREFOR NEW PAINT.
REMOVE EXISTING CEILING GRID AND LIGHTS. SEE ELECTRICAL FORADDITIONAL DETAILS. CEILING GRID WALL ANGLE TO REMAIN ATTYPICAL CORRIDORS HFL#01, HFL#02, AND HFL#03, FLOORS 2-18, TOBE REUSED FOR FUTURE NEW CEILING INSTALLATION.
REMOVE/ABATE SPRAY-ON TEXTURED CEILING ABOVE EXISTING LAY-IN CEILING. SEE SPECS SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
REMOVE EXISTING GWB CEILING AND LIGHTS. SEE ELECTRICAL FORADDITIONAL DETAILS.
CUT OPENING IN EXISTING ROOF DECK AS PART OF PHASE A. SEEA2.3 KEYNOTES FOR SOFFIT TO BE BUILT IN PHASE A TO ENCLOSEROOF DECK OPENING. PARTIALLY SCRAPE/ABATE EXISTINGASBESTOS CONTAINING SPRAY TEXTURE CEILING TO ALLOW FORTEMORARY SOFFIT ENCLOSURE. EXISTING CHASE WALL TO REMAINDURING PHASE A.
REMOVAL OF EXISTING GRILL, WHERE OCCURS, AND PATCHING OFSHEETROCK TO BE COMPLETED BY OTHERS. G.C. TO PAINT.
1
2
4
3
5
6
7
SELECTIVE REMOVAL OF TEXTURED CEILING IN ORDER TO ALLOWFOR INSTALLATION OF STEEL ANGLES,DUCTWORK, PIPING, ANDASSOCIATED HANGING DEVICES. SEE MECHANICAL, ELECTRICAL,PLUMBING AND SPEC. SECTION 010000 - SPECIAL CONDITIONSAND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING METAL SOFFIT. SEE MECHANICAL, ELECTRICAL,PLUMBING FOR ADDITIONAL SCOPE TO BE REMOVED. MAINTAINEXISTING SOFFIT CEILING ANGLE CONNECTION TO BE REUSED.SEE SPEC. SECTION 010000 - SPECIAL CONDITIONS ANDREQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASEDPAINT INVESTIGATION REPORT.
EXISTING LIGHT TO BE REMOVED AND STORED FOR REINSTALLIONDURING THIS SCOPE OF WORK. CONTRACTOR TO VERIFY ALLLIGHTS ARE WORKING PRIOR TO REMOVAL AND REPORT TOOWNER/ARCHITECT ANY FIXTURES THAT ARE NOT WORKING. SEEELECTRICAL FOR FULL SCOPE OF WORK AND COORDIATION OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID ANDALTERNATE NO. 1.
REMOVE EXISTING METAL SOFFIT. SEE MECHANICAL, ELECTRICAL,PLUMBING FOR ADDITIONAL SCOPE TO BE REMOVED. REMOVEEXISTING SOFFIT CEILING ANGLE AND PREPARE CEILING TO BEEXPOSED FOR NEW TEXTURED SPRAY MATERIAL. SEE REFLECTEDCEILING PLAN AND SPEC. SECTION 010000 - SPECIAL CONDITIONSAND REQUIREMENTS/ASBESTOS INVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATION REPORT.
REMOVE EXISTING METAL SOFFIT AND CEILING ANGLECOMPLETELY.
REMOVE EXISTING LIGHT. SEE ELECTRICAL FOR FULL SCOPE OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID ANDALTERNATE NO. 1.
REMOVE /ABATE SPRAY-ON TEXTURED CEILING COMPLETELY ANDPREPARE FOR NEW SKIM COAT CEILING FINISH AS SHOWN ONREFLECTED CEILNG PLAN, SEE SPECS. SEE SPEC SECTION010000 SPECIAL CONDITIONS AND REQUIREMENTS/ASBESTOSINVESTIGATION REPORT/LEAD-BASED PAINT INVESTIGATIONREPORT.
SELECTIVE REMOVAL OF APC CEILING TILE ONLY INSTALLED INPHASE A TO ALLOW FOR REMOVAL OF PIPING, SEE PLUMBING.PROTECT EXISTING CEILING TILE, GRID AND AND ADJACENTCEILING MATERIALS AND REINSTALL CEILING TILE AFTERREMOVAL OF PHASE B PLUMBING SCOPE IS COMPLETE.
SELECTIVE PATCHING OF EXISTING GWB BY OTHERS, SEEMECHANICAL.
SELECTIVE REMOVAL OF APC CEILING TILE ONLY INSTALLED INPHASE A TO ALLOW FOR REQUIRED MECHANICAL, ELECTRICALAND PLUMBING CONNECTIONS. PROTECT EXISTING CEILING TILE,GRID AND AND ADJACENT CEILING MATERIALS AND REINSTALLCEILING TILE AFTER REMOVAL OF PHASE B PLUMBING SCOPE ISCOMPLETE.
A
B
C
D
E
F
G
H
J
K
1. SEE LEGEND. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BEDISTURBED DURING PHASE A TO PREVENT PHASE B HAZARDOUSMATERIALS FROM BEING DISTURBED. THE BOUNDARY WALLSEPARATING PHASE A AND PHASE B IS NOT TO BE DISTURBED DURINGPHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAININGMATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOTSHOWN TO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OFDEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THEEXISTING DRAWINGS PROVIDED BY THE OWNER. GENERALCONTRACTOR AND SUB-CONTRACTORS ARE TO VERIFY EXISTINGCONDITIONS PRIOR TO BID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TODOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECTWITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOTSHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICALDRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FORADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUTCONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS,PIPES AND DUCTWORK.7. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION SCOPE. REPAIR OR REPLACEMENT OFDAMAGED AREAS NOT IN THIS SCOPE SHALL BE INCLUDED IN THE WORK,WITH NO ADDITIONAL COST TO THE OWNER.8. ELECTRICAL CONTRACTOR IS TO VERIFY ALL CEILING MOUNTEDELECTRICAL DEVICES ARE IN WORKING CONDITION AT COMMENCEMENTOF DEMOLITION/CONSTRUCTION. SEE ELECTRICAL DRAWINGS ANDSPECS FOR ALL SCOPE RELATED TO CEILING MOUNTED DEVICES PRIORTO COMMENCEMENT OF DEMOLITION/CONSTRUCTION.9. ALL EXISTING WALL SCONCES/LIGHTING TO REMAIN UNLESS NOTEDOTHERWISE.10. ALL CEILING LIGHTING TO REMAIN UNLESS NOTED OTHERWISE.11. SEE ELECTRICAL FOR FULL SCOPE AND COORDINATION OF LIGHTINGDEMOLITION/CONSTRUCTION FOR BASE BID AND ALTERNATE NO. 1.12. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BEUSED DURING THE DEMOLITION AND CONSTRUCTION PERIOD.ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THECONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOBPHASE. SEE SPECIFICATIONS.13. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OFFINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASINGCLARIFICATION.
1. SEE LEGEND. PHASE B AREA AND ADJACENT WALLS ARE NOT TO BEDISTURBED DURING PHASE A TO PREVENT PHASE B HAZARDOUSMATERIALS FROM BEING DISTURBED. THE BOUNDARY WALL SEPARATINGPHASE A AND PHASE B IS NOT TO BE DISTURBED DURING PHASE A.2. CONTACT OWNER UPON DISCOVERY OF ANY ASBESTOS-CONTAININGMATERIALS OR OTHER SUSPECTED HAZARDOUS MATERIALS NOT SHOWNTO BE REMOVED OR ALTERED WITHIN THE PROJECT SCOPE.3. FIELD VERIFY EXISTING CONDITIONS PRIOR TO COMMENCEMENT OFDEMOLITION AND NEW WORK. INFORMATION SHOWN IS BASED ON THEEXISTING DRAWINGS PROVIDED BY THE OWNER. GENERAL CONTRACTORAND SUB-CONTRACTORS ARE TO VERIFY EXISTING CONDITIONS PRIOR TOBID AND PRIOR TO CONSTRUCTION.4. CONTRACTOR SHALL PHOTOGRAPH AND VIDEO ALL SPACES PRIOR TOCOMMENCEMENT OF DEMOLITION/RENOVATION/NEW WORK TODOCUMENT PRE-CONSTRUCTION CONDITIONS. PROVIDE ARCHITECTWITH ELECTRONIC COPIES OF PHOTOGRAPHS AND VIDEO.5. CORE DRILLING IN EXISTING SLAB FOR NEW UTILITY SERVICE IS NOTSHOWN ON THIS PLAN. SEE MECHANICAL, PLUMBING, AND ELECTRICALDRAWINGS FOR REQUIRED UTILITY ROUTING.6. SEE MECHANICAL, PLUMBING AND ELECTRICAL DRAWINGS FORADDITIONAL ITEMS TO REMAIN AND BE PROTECTED THROUGHOUTCONSTRUCTION, INCLUDING DATA AND POWER CONDUITS, LIGHTS, PIPESAND DUCTWORK.7. PROTECT EXISTING BUILDING SCOPE NOT INCLUDED INDEMOLITION/CONSTRUCTION SCOPE. REPAIR OR REPLACEMENT OFDAMAGED AREAS NOT IN THIS SCOPE SHALL BE INCLUDED IN THE WORK,WITH NO ADDITIONAL COST TO THE OWNER.8. ELECTRICAL CONTRACTOR IS TO VERIFY ALL CEILING MOUNTEDELECTRICAL DEVICES ARE IN WORKING CONDITION AT COMMENCEMENTOF DEMOLITION/CONSTRUCTION. SEE ELECTRICAL DRAWINGS AND SPECSFOR ALL SCOPE RELATED TO CEILING MOUNTED DEVICES PRIOR TOCOMMENCEMENT OF DEMOLITION/CONSTRUCTION.9. ALL EXISTING WALL SCONCES/LIGHTING TO REMAIN UNLESS NOTEDOTHERWISE.10. ALL CEILING LIGHTING TO REMAIN UNLESS NOTED OTHERWISE. SEEELECTRICAL FOR FULL SCOPE OF LIGHTING DEMOLITION/CONSTRUCTION.11. COORDINATE PARTIAL/SELECTIVE REMOVAL OF APC CEILING TOALLOW FOR MECHANICAL, PLUMBING AND ELECTRICAL CONNECTIONSREQUIRED IN PHASE B SCOPE. PROTECT EXISTING CEILING TILE AND GRID(INSTALLED IN PHASE A) AND REINSTALL AFTER REQUIRED CONNECTIONSHAVE BEEN MADE. ALL CEILING TILES DAMAGED DURING CONSTRUCTIONSHALL BE REPLACE BY CONTRACTOR AT NO ADDITIONAL COST TOOWNER. SEE MECHANICAL, ELECTRICAL AND PLUMBING DRAWINGS FORFULL SCOPE OF WORK.12. SEE ELECTRICAL DRAWINGS FOR FULL SCOPE AND COORDINATION OFLIGHTING DEMOLITION/CONSTRUCTION FOR BASE BID AND ALTERNATENO. 1.13. ELEVATORS ARE NOT PART OF THE PROJECT SCOPE BUT MAY BEUSED DURING THE DEMOLITION AND CONSTRUCTION PERIOD.ELEVATORS SHOULD BE PROTECTED, CLEANED AND RETURNED TO THECONDITION IN WHICH THEY WERE FOUND AT THE END OF EACH JOBPHASE. SEE SPECIFICATIONS.14. SEE FINISH SCHEDULE AND FINISH PLANS FOR FULL SCOPE OFFINISHES. KEYNOTES REFERRING TO FINISHES ARE FOR PHASINGCLARIFICATION.
N
PHASE A WORK - NOTE TO CONTRACTORS:
1. NO PENETRATIONS OR ATTACHMENTS TO THE EXISTING GYPSUM BOARD PARTITIONS WILL BE ALLOWED ONCE THEASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
2. THE CONTRACTOR SHALL NOT COME IN CONTACT WITH THE GYPSUM BOARD MATERIAL THAT IS TO REMAIN IN PLACE AFTERTHE PARTIAL ABATEMENT OF ASBESTOS FROM THE CORRIDOR PARTITIONS ON THE EXISTING FLOORS 2 THRU 18 AND OTHERPARTITIONS ON THE BASEMENT AND GROUND LEVELS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THEGYPSUM BOARD MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
PHASE B WORK - NOTE TO CONTRACTORS:
1. DURING THE PROCESS OF INSTALLING HANGERS, SOFFITS, FAN COILS, METAL PAN COVERS, NEW PARTITIONS OR ANY OTHERMATERIAL OR EQUIPMENT AT THE CEILINGS OF THE EXISTING RESIDENT ROOMS ON FLOORS 2 THRU 18, THE CONTRACTORSHALL NOT COME IN CONTACT WITH THE SPRAY APPLIED TEXTURED CEILING MATERIAL THAT IS TO REMAIN IN PLACE AFTER THEPARTIAL ABATEMENT OF ASBESTOS FROM THE CEILINGS. CONTAMINATION OF THESE SPACES CAUSED BY DAMAGE TO THECEILING MATERIAL SHALL BE CLEANED UP AT THE CONTRACTOR'S EXPENSE, INCLUDING BUT NOT LIMITED TO, COSTSASSOCIATED WITH CLEARING THESE SPACES FOR RE-ACCESS, I.E. AIR SAMPLING.
2. DURING THE PROCESS OF INSTALLING UL RATED RACEWAYS AT CORRIDOR WALL PENETRATION, INSTALLATION OF NEWPARTITIONS, THE CONTRACTOR SHALL NOT DISTURB THE EXISTING GYPSUM BOARD IN ANY FASHION. NO PENETRATIONS WILLBE ALLOWED ONCE THE ASBESTOS ABATEMENT HAS BEEN COMPLETED BY THE ABATEMENT CONTRACTOR.
REFERENCED ON: 1/4" = 1'-0"D2.31 18TH FLOOR DEMOLITION REFLECTED CEILING PLAN
LEGEND
PHASE A - DEMO REFLECTED CEILING PLAN KEYNOTES
PHASE B - DEMO REFLECTED CEILING PLAN KEYNOTES
PHASE A - GENERAL DEMOLITION RCP NOTES
PHASE B- GENERAL DEMOLITION RCP NOTES
D2.3
18TH
FLO
OR D
EMOL
ITIO
NRE
FLEC
TED
CEILI
NG P
LAN
RMB
SAL
Related Documents
