This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
YF23 - EASYBUILD (with or without Power Pod) - V1.04 Designed by Nick Cara (NAC) [email protected]
NOTES:- Assemble plane parts in numbered order. Some parts may be �tted at angles, some cuts & tab holes (in bold) need trimming. Bevel or curve all leading edges. Trim and sand intake to a curve. Use Hot Glue for all parts except carbon rods. Protect lower edges with packing tape. Single Elevator or Split Elevons. If using Split Elevons connect both Ailerons and Elevons to a single pair of servos. Mount eletronics and battery using Velcro. Balance the plane at COG mark by moving the battery possition.
(Mount at 45 degrees using angle guide)
4Cut for Power Pod
MAKE 2
MAKE 2
OPTIONAL - Alternante location for servos when NOT using Power Pod
9
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
YF23 - EASYBUILD (with or without Power Pod) - V1.04 Designed by Nick Cara (NAC) [email protected]
NOTES:- Assemble plane parts in numbered order. Some parts may be �tted at angles, some cuts & tab holes (in bold) need trimming. Bevel or curve all leading edges. Trim and sand intake to a curve. Use Hot Glue for all parts except carbon rods. Protect lower edges with packing tape. Single Elevator or Split Elevons. If using Split Elevons connect both Ailerons and Elevons to a single pair of servos. Mount eletronics and battery using Velcro. Balance the plane at COG mark by moving the battery possition.
(Mount at 45 degrees using angle guide)
4Cut for Power Pod
MAKE 2
MAKE 2
OPTIONAL - Alternante location for servos when NOT using Power Pod
9
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
(Mount at 45 degrees using angle guide)
4Cut for Power Pod
MAKE 2
MAKE 2
OPTIONAL - Alternante location for servos when NOT using Power Pod
9
1
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
41 20 3
INCH
41 20 3CM
5 6 7 8 9 10
(Mount at 45 degrees using angle guide)
4Cut for Power Pod
MAKE 2
MAKE 2
OPTIONAL - Alternante location for servos when NOT using Power Pod
9
2
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
YF23 - EASYBUILD (with or without Power Pod) - V1.04 Designed by Nick Cara (NAC) [email protected]
Control points (Make from old plastic credit card)
NOTES:- Assemble plane parts in numbered order. Some parts may be �tted at angles, some cuts & tab holes (in bold) need trimming. Bevel or curve all leading edges. Trim and sand intake to a curve. Use Hot Glue for all parts except carbon rods. Protect lower edges with packing tape. Single Elevator or Split Elevons. If using Split Elevons connect both Ailerons and Elevons to a single pair of servos. Mount eletronics and battery using Velcro. Balance the plane at COG mark by moving the battery possition.
MAKE 2
ANGLE GUIDE (45 degrees)
3mm PLYWOOD
MOTOR MOUNT PARTS
Glue Plywood onto Depron
(If NOT using Power Pod)
6
(Mount at 45 degrees using angle guide)
4Cut for Power Pod
MAKE 2
MAKE 2
OPTIONAL - Alternante location for servos when NOT using Power Pod
9
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
YF23 - EASYBUILD (with or without Power Pod) - V1.04 Designed by Nick Cara (NAC) [email protected]
NOTES:- Assemble plane parts in numbered order. Some parts may be �tted at angles, some cuts & tab holes (in bold) need trimming. Bevel or curve all leading edges. Trim and sand intake to a curve. Use Hot Glue for all parts except carbon rods. Protect lower edges with packing tape. Single Elevator or Split Elevons. If using Split Elevons connect both Ailerons and Elevons to a single pair of servos. Mount eletronics and battery using Velcro. Balance the plane at COG mark by moving the battery possition.
MOTOR MOUNT PARTS(If NOT using Power Pod)
(Mount at 45 degrees using angle guide)
4Cut for Power Pod
MAKE 2
MAKE 2
OPTIONAL - Alternante location for servos when NOT using Power Pod
9
Cut here if required to �t 100cm sheet of Depron
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
YF23 - EASYBUILD (with or without Power Pod) - V1.04 Designed by Nick Cara (NAC) [email protected]
Control points (Make from old plastic credit card)
NOTES:- Assemble plane parts in numbered order. Some parts may be �tted at angles, some cuts & tab holes (in bold) need trimming. Bevel or curve all leading edges. Trim and sand intake to a curve. Use Hot Glue for all parts except carbon rods. Protect lower edges with packing tape. Single Elevator or Split Elevons. If using Split Elevons connect both Ailerons and Elevons to a single pair of servos. Mount eletronics and battery using Velcro. Balance the plane at COG mark by moving the battery possition.
(Mount at 45 degrees using angle guide)
4Cut for Power Pod
MAKE 2
MAKE 2
OPTIONAL - Alternante location for servos when NOT using Power Pod
9
Cut here if required to �t 100cm sheet of Depron
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
(Mount at 45 degrees using angle guide)
4Cut for Power Pod
MAKE 2
MAKE 2
OPTIONAL - Alternante location for servos when NOT using Power Pod
9
Velcro/Magnet (Power Pod)
CG = 17 cm
Velcro/Magnet (Power Pod)
Battery position
Max prop size 7”
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
(Mount at 45 degrees using angle guide)
4Cut for Power Pod
MAKE 2
MAKE 2
OPTIONAL - Alternante location for servos when NOT using Power Pod
9
Control point
Max prop size 7”
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
YF23 - EASYBUILD (with or without Power Pod) - V1.04 Designed by Nick Cara (NAC) [email protected]
Control points (Make from old plastic credit card)
NOTES:- Assemble plane parts in numbered order. Some parts may be �tted at angles, some cuts & tab holes (in bold) need trimming. Bevel or curve all leading edges. Trim and sand intake to a curve. Use Hot Glue for all parts except carbon rods. Protect lower edges with packing tape. Single Elevator or Split Elevons. If using Split Elevons connect both Ailerons and Elevons to a single pair of servos. Mount eletronics and battery using Velcro. Balance the plane at COG mark by moving the battery possition.
MAKE 2
ANGLE GUIDE (45 degrees)
3mm PLYWOOD
MOTOR MOUNT PARTS
Glue Plywood onto Depron
(If NOT using Power Pod)
6
(Mount at 45 degrees using angle guide)
4Cut for Power Pod
MAKE 2
MAKE 2
OPTIONAL - Alternante location for servos when NOT using Power Pod
9
2
Control point when using split elevons
Single Elevator or split Elevons
Control point when not using split elevons
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
3mm PLYWOOD
Glue Plywood onto Depron
(If NOT using Power Pod)
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
ANGLE GUIDE (45 degrees)
4Cut for Power Pod
MAKE 2
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
Velcro/Magnet (Power Pod)
Velcro/Magnet (Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
Control point
2
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
YF23 - EASYBUILD (with or without Power Pod) - V1.04 Designed by Nick Cara (NAC) [email protected]
Control points (Make from old plastic credit card)
NOTES:- Assemble plane parts in numbered order. Some parts may be �tted at angles, some cuts & tab holes (in bold) need trimming. Bevel or curve all leading edges. Trim and sand intake to a curve. Use Hot Glue for all parts except carbon rods. Protect lower edges with packing tape. Single Elevator or Split Elevons. If using Split Elevons connect both Ailerons and Elevons to a single pair of servos. Mount eletronics and battery using Velcro. Balance the plane at COG mark by moving the battery possition.
MAKE 2
ANGLE GUIDE (45 degrees)
3mm PLYWOOD
MOTOR MOUNT PARTS
Glue Plywood onto Depron
(If NOT using Power Pod)
6
Control point when using split elevons
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
MAKE 26
3
7
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
OPTIONAL - Alternante location for servos when NOT using Power Pod
3(If NOT using Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
MAKE 29
3(If NOT using Power Pod)
3
7
83 Elevator servo when not using split elevons
(If NOT using Power Pod)
5Hatch to access electronics and battery
Magnet/Velcro
Cut for Power Pod
(If NOT using Power Pod)
5
YF23 - EASYBUILD (with or without Power Pod) - V1.04 Designed by Nick Cara (NAC) [email protected]
Control points (Make from old plastic credit card)
NOTES:- Assemble plane parts in numbered order. Some parts may be �tted at angles, some cuts & tab holes (in bold) need trimming. Bevel or curve all leading edges. Trim and sand intake to a curve. Use Hot Glue for all parts except carbon rods. Protect lower edges with packing tape. Single Elevator or Split Elevons. If using Split Elevons connect both Ailerons and Elevons to a single pair of servos. Mount eletronics and battery using Velcro. Balance the plane at COG mark by moving the battery possition.