product guide features • 4 models … YB4409: 8.5T (7.7mt) 3-section boom with 25 ft. 2 in. (7.6m) Tip Height YB4409XL: 8.5T (7.7mt) 3-section boom with 33 ft. 6 in. (10.2m) Tip Height YB4409-2: 9.0T (8.1mt) 3-section boom with 38 ft. 2 in. (11.6m) Tip Height YB4411: 10.5T (9.5mt) 3-section boom with 38 ft. 2 in. (11.6m) Tip Height • 6 ft. (1.8m) fixed extension (YB4409 / XL) and 12 ft. (3.6m) offsettable swingaway extension (YB4409-2 & YB4411) • 70 bhp (52.2 kW) GM EFI dual fuel engine or 99 bhp (73.8 kW) Cummins diesel engine YB 4400 Series Industrial Hydraulic Crane contents Features 2 Specifications 3 YB4409 Dimensions 5 Range Diagram 6 Load Chart 7 YB4409XL Dimensions 8 Range Diagram 9 Load Chart 10 YB4409-2 Dimensions 11 Range Diagram 12 Load Chart 13 YB4411 Dimensions 14 Range Diagram 15 Load Chart 16 YB4409 (metric) Range Diagram 17 DIN/ISO Load Chart 18 YB4409XL (metric) Range Diagram 19 DIN/ISO Load Chart 20 YB4409-2 (metric) Range Diagram 21 DIN/ISO Load Chart 22 YB4411 (metric) Range Diagram 23 DIN/ISO Load Chart 24 www.manitowoccranegroup.com *Product may be shown with optional equipment.
28
Embed
YB4400 Series - Maxim Crane Works...pivoted fully forward. Boom Elevation Single double acting hydraulic cylinder with integral holding valve. Elevation: 0 to 60 for the YB4409 & YB4409XL
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
productguide
features
• 4 models …
YB4409: 8.5T (7.7mt) 3-section boom with25 ft. 2 in. (7.6m) Tip Height
YB4409XL: 8.5T (7.7mt) 3-section boomwith 33 ft. 6 in. (10.2m) Tip Height
YB4409-2: 9.0T (8.1mt) 3-section boomwith 38 ft. 2 in. (11.6m) Tip Height
YB4411: 10.5T (9.5mt) 3-section boomwith 38 ft. 2 in. (11.6m) Tip Height
• 6 ft. (1.8m) fixed extension (YB4409 / XL)and 12 ft. (3.6m) offsettable swingawayextension (YB4409-2 & YB4411)
BoomYB4409: 9 ft. 8 in. – 21 ft. 2 in. (2.9m – 6.5m) three- section fullpower boom.Maximum tip height: 25 ft. 2 in. (7.6m)
YB4409XL: 12 ft. 8 in. – 30 ft. 2 in. (3.8m – 9.2m) three- sectionfull power boom.Maximum tip height: 33 ft. 6 in. (10.2m)
YB4409-2 & YB4411: 13 ft. 10 in. – 32 ft. 10 in. (4.2m – 10.0m)three-section full power boom.Maximum tip height: 38 ft. 2 in. (11.6m)
*Optional BoomYB4409 & YB4409XL: Manual 4th main boom fly section
*Boom ExtensionYB4409 & YB4409XL: 6 ft. (1.8m) fixed pin on extensionYB4409-2 & YB4411: 12 ft. (3.6m) offsettable extension
12-18 ft. (3.6-5.4m) telescopic offsettable extension
Boom NoseYB4409 / XL: Single sheave non-pivoting YB4409-2 & YB4411 only: Single sheave, 3-position (0˚, + 30˚, +80˚) pivoting boom nose for minimizing head spacerequirements. Lowers head height 10.5 in. (0.26m) when nose ispivoted fully forward.
Boom ElevationSingle double acting hydraulic cylinder with integral holdingvalve.Elevation: 0° to 60° for the YB4409 & YB4409XL
0° to 72° for the YB4409-2 & YB4411
Anti-Two Block DeviceStandard anti-two block device, when activated, provides anaudible warning to the crane operator and disengages all cranefunctions whose movement can cause two-blocking.
Load Indicator A simple, effective, and easy to use load indicating system
used in conjunction with the anti-two block system to assist theoperator in efficient operation of the unit within the limits of theload chart. The display panel displays the hook load and warnsthe operator when a preset load capacity is exceeded. Thewarning is by a flashing light on the display panel. Inconjunction with the load display panel (receiver), there is awireless transmitter and load sensing pin attached to the boomhead that transmits the hook load to the display panel.
*Rated Capacity Limiter (RCL)Similar to the Load Indicator, but stops the telescope out
and boom lift down function when a load limit is exceeded.Uses a similar display panel with the addition of displaying boomangle and boom length read outs on the panel.
*Load Moment Indicator (LMI)Digital display of boom angle, boom length, boom radius,capacity, and allows for operator in-put to set the limits based onload chart. Displays color coded light bar and audible alarmwith function cutout if load exceeds entered parameters.
Swing Ball bearing swing circle with 360° continuous rotation. Hydraulic driven worm gear and pinion.Maximum speed: 2.05 rpm
YB4409 & YB4409XL: Six section valve bank mounted in dashpanel with direct mechanical linkage for low effort lever control.
YB4409-2 & YB4411: Six section valve bank chassis mounted;operated via dash mounted, pilot pressure hydraulic joysticks.
Return line filter with full flow by-pass protection and serviceindicator.
23.5 gallon (89 L) hydraulic reservoir with sight level gauge andsteel side plating to guard against side impact damage.
Hoist Specifications
YB4409 / XL: Worm drive with counter-balance valving. Equalspeed power up and down.
YB4409-2 & YB4411: Piston motor drive w/springapplied/hydraulic released brake.
Drum Diameter:YB4409 / XL: 9.69 in. (0.24m)YB4409-2 & YB4411: 10.63 in. (0.27m)
Maximum Single Line Pull: YB4409 / XL: 10,700lb (4 854kg)YB4409-2 & YB4411: 14,000lb (6 350 kg)
Maximum Single Line Speed:YB4409 / XL: 88 FPM (26.8m / min)YB4409-2 & YB4411: 120FPM (36.6m / min)
Maximum Permissible Single Line Pull:YB4409 / XL : 8,500lb (3 855 kg)(1/2” [12.7mm] Python Ultra XIPS) YB4409-2 & YB4411: 10,000lb (4 536kg)(9/16” [14.0mm] EEIPS)
Rope Length :YB4409 / XL: (3-section boom) 97 ft. (29.6m)
(4-section boom) 130 ft. (39.6m)YB4409-2 & YB4411: 120 ft. (36.6m)
*Denotes optional equipment
Boom
Boom
Boom Extension
Boom Nose
Boom Elevation
Load Moment & Anti-Two Block System
Load Moment & Anti-Two Block System
Load Moment & Anti-Two Block System
Load Moment & Anti-Two Block System
Swing
Hydraulic System
Hoist
4
YB4400
Seri
es
specifications
Carrier
FrameHigh strength alloy steel constructed with integral outriggerhousings; front and rear lifting, towing, and tie-down lugs. 42 ft.2
carrydeck size with 14,000 lb (6 350kg) carrying capacity(YB4409 / XL / YB4409-2) and 17,000 lb (7 711kg) carryingcapacity (YB4411). Deck coated with anti-skid treatment.
OutriggersYB4409, YB4409XL & YB4409-2: Front and rear oblique typebeams at all four corners with integral holding valves. Outriggerpads form an integral part of the beam.YB4411: Hydraulic telescoping beam with oblique type jackprovides extended and down and retracted and down liftingcapacities. Integral holding valves on both beam and jack.
Outrigger ControlsYB4409-2, YB4409 & YB4409XL: Lever controls located on dashpanel which operate the beams in pairs from side to side.YB4411: Two switch operation mounted on dash panel. One -3-position rocker switch to select all beams / jacks, left beams /jacks only, or right beams / jacks only. Separate -4- way toggleswitch to activate beams out / in and jacks down / up. Levelbubble indicator located inside operators compartment.*Independent outrigger controls available as an option.
Operators Control StationFrame mounted, open air style control station with cab shell.Includes all crane functions, driving controls, and overheadsafety glass. Other standard equipment include a durableweather resistant seat with seat belt, hourmeter, sight levelbubble, and fire extinguisher. The dash panel includes engineoil pressure gauge, engine water temperature gauge, fuelgauge, transmission low oil and high temperature warning lights,low battery warning light, and brake system low pressurewarning light. The LSI (load indicator) receiver is mounted to thetop of the dash and provides warning for A2B and exceededload capacity.
*Operators Control Station EnclosedIncludes the standard cab shell with the addition of front andrear glass and sliding glass on the right side. Hinged full doorwith sliding glass.
Front windshield wiper and heater and defroster is included.
Fuel Tank Capacity18.5 gallon (70 L) all steel construction with steel side plate toguard against side impact.
TransmissionYB4409 / XL & YB4409-2: Clark synchromesh -4- speeds
forward and reverse with stalk mountedforward/reverse selector.
YB4411 : Clark powershift -4- speeds forward and reverse.Stalk mounted shifter on left side of steeringcolumn.
AxlesFront: Carraro planetary drive/steer with internal multi-wet-discbrakes and limited slip differential.Rear: Fabricated non-drive steer with disc brakes
Tires10.00 x 15 14PR pneumatic
BrakesHydraulic actuated internal wet-disc service brakes acting on allfour wheels. A dash mounted toggle switch activates the drydisc parking brake on the transmission output yoke with a dashwarning light.
SuspensionFront: Rigid mounted to frame.Rear: Rigid mounted to frame
LightsRecessed mounted, includes head, tail, rear work, stop, and turnsignals.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
35
5
10
0
5
10
15
20
25
3S
EC
TIO
N
4S
EC
TIO
N
50 1510 2520 30
30
35
40
45°
30°
60°
0°
15°
10 5 0 5 10 15 20 25 30 35
10
0
5
15
20
30
25
35
40
6'JI
B
YB4409H
EIG
HT
FR
OM
GR
OU
ND
INF
EE
T
OPERATING RADIUS IN FEET FROM AXIS OF ROTATION
range diagram
7
YB4400
Seri
es
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
*LIMIT RATINGS TO 11,800 LBS WHEN 3RD SECTION IS EXTENDED ANY AMOUNT.
JIB CAPACITY IS LIMITED BY BOTH STRUCTURALCAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURALSTRENGTH, DO NOT RELY ON TIPPING.
YB4409
load chart
8
YB4400
Seri
es
dimensions
1' 0"(0.30 m)
5' 11.88"(1.33 m)
4' 9.13"(1.45 m)
2' 11.75"(0.91 m)
4' 2.88"(1.88 m)
1' 11.5"(0.60 m)
3.12"(0.08 m)
3' 3.5"(1.0 m)
1' 6"(0.46 m)
3' 4.5"(1.00 m)
5' 7"(1.70 m)
5' 8.38"(1.74 m)
5' 8.38"(1.74 m)
5' 11.88"(1.82 m)
11' 11.75"(3.65 m)
15' 7"(4.75 m)
1' 0"(0.30 m)
9' 7.5"(2.93 m)
9.5" (On Tires)(0.25 m)
3' 6"(1.07")
3' 2"(0.97 m)
7' 10"(2.39 m)
5' 9.7"(1.77 m)
5' 3"1.60 m)
6' 4"(1.93 m)
6' 6.25"(1.99 m)
9' 2.75"(2.81 m)
10' 2"(3.10 m)
YB4409XL Dimensions
1' 0"(0.30 m)
5' 11.88"(1.33 m)
4' 9.13"(1.45 m)
2' 11.75"(0.91 m)
4' 2.88"(1.88 m)
1' 11.5"(0.60 m)
3.12"(0.08 m)
3' 3.5"(1.0 m)
1' 6"(0.46 m)
3' 4.5"(1.00 m)
5' 7"(1.70 m)
5' 8.38"(1.74 m)
5' 8.38"(1.74 m)
5' 11.88"(1.82 m)
11' 11.75"(3.65 m)
15' 7"(4.75 m)
1' 0"(0.30 m)
9' 7.5"(2.93 m)
9.5" (On Tires)(0.25 m)
3' 6"(1.07")
3' 2"(0.97 m)
7' 10"(2.39 m)
5' 9.7"(1.77 m)
5' 3"1.60 m)
6' 4"(1.93 m)
6' 6.25"(1.99 m)
9' 2.75"(2.81 m)
10' 2"(3.10 m)
YB4409XL DimensionsYB4409XL
9
YB4400
Seri
es
YB4409XL
355
NOITCES
3
NOITCES
4
50 1510 2520 30
45°
30°
60°
40
0°
15 °
5 0 5 10 15 20 25 30 35 40
10
0
5
15
20
30
25
35
40
45
45
45
BIJ'6
50
5
100
10
15
20
25
30
35
40
45
10
50
OPERATING RADIUS IN FEET FROM AXIS OF ROTATION
HEIG
HTFR
OMGR
OUND
INFE
ET
range diagram
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
10
YB4400
Seri
es
load chart
YB4409XL
8. Do not induce external side loads to boom or jib.
is 14,000 lbs with 10:00 x 15 tires. Tire inflation at
12,000 lbs. For deck loads only, the maximum load
7. The maximum combined total boom and deck load is
next larger radius.
6. For operating radius not shown, use load rating of the
on a smooth hard level surface with boom retracted
may be transported at a maximum speed of 2.5 mph
tires, and proper inflation pressure (100 psi). Loads on rubber
5. Ratings on rubber depend on tire capacity, condition of
4. Ratings on outriggers are with outriggers fully extended.
be considered as part of the load. See reductrion chart.
hook blocks, slings, etc., except the hoist rope, shall
3. The weights of all load handling devices, such as hooks,
proper handling must all be taken into account by the
Hazardous surroundings, experience of personnel and
Practical working loads depend on supporting surface,
leveled, standing on a firm, uniform supporting surface.
based on freely suspended loads with the machine
not exceed 75% of actual tipping. These ratings are
of actual tipping. The rated loads shown on rubber do
2. The rated loads shown on outriggers do not exceed 85%
the supporting surface, before loading, to the center
distance from a projection of the axis of rotation to
operating radius. The operating radius is the horizontal
of boom lengths and angles may be used to obtain
determined by operating radius only. Any combination
of vertical hoist line or tackle with load applied.
operating radius, and other factors affecting stability.
operator.
to the shortest length possible and centered over front.
at 100 psi.
RELY ON TIPPING.
DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
30°
15° 15°
30°
FRONT REAR
SIDE
SIDE
3-SECTION BOOM OR 4-SECTION BOOM WITH 4TH RETRACTED
RADIUS
OPERATING
0-17000lbs
2-PART
0-8500lbs
1-PART
RIGGING CHART
950 lbs
1100 lbs
1300 lbs
1500 lbs
1800 lbs
2150 lbs
2750 lbs
3800 lbs
5400 lbs
8000 lbs
32.0 ft
30.0 ft
28.0 ft
26.0 ft
24.0 ft
22.0 ft
20.0 ft
18.0 ft
16.0 ft
14.0 ft
12.0 ft
10.0 ft
8.0 ft
6.0 ft
5.0 ft
2900 lbs
3300 lbs
3800 lbs
4450 lbs
33.5 ft
1450 lbs
1150 lbs
950 lbs
800 lbs
650 lbs
550 lbs
5600 lbs
3800 lbs
2700 lbs
1950 lbs
4650 lbs
2050 lbs
2350 lbs
2700 lbs
3150 lbs
3800 lbs
4-SECTION BOOM WITH 4TH EXTENDED
ON RUBBER
28.0 ft
33.5 ft
36.0 ft
30.0 ft
32.0 ft
5.0 ft
16.0 ft
22.0 ft
24.0 ft
26.0 ft
18.0 ft
20.0 ft
10.0 ft
12.0 ft
14.0 ft
6.0 ft
8.0 ft
FRONT
ON OUTRIGGERS
360°
950 lbs
800 lbs
700 lbs
625 lbs
550 lbs
600 lbs
500 lbs
400 lbs
325 lbs
250 lbs
2000 lbs
1800 lbs
1600 lbs
1400 lbs
1250 lbs
2750 lbs
2450 lbs
2200 lbs
1950 lbs
1750 lbs
WIRE ROPE: 1/2 inch diameter
Min. breaking strength 29750 lbs.
27.0 ft 850 lbs 500 lbs 2750 lbs 1900 lbs 27.0 ft
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND
42.0 ft
40.0 ft
38.0 ft
43.0 ft
475 lbs
325 lbs
350 lbs
400 lbs
125 lbs
150 lbs
200 lbs
225 lbs
1300 lbs
1350 lbs
1475 lbs
1625 lbs
875 lbs
925 lbs
1025 lbs
1125 lbs
525 lbs
600 lbs
700 lbs
800 lbs
275 lbs
325 lbs
400 lbs
475 lbs
1875 lbs
2025 lbs
2275 lbs
2525 lbs
1300 lbs
1425 lbs
1600 lbs
1775 lbs
REDUCTION CHART
FRONT 360°
ON RUBBER
FRONT
ON OUTRIGGERS
360° FRONT 360°
RADIUS
OPERATING
MO
OB
NIA
MB I
J
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
140 lbs
100 lbs
0 lbs
150 lbs
N/A
100 lbs
N/A
0 lbs
JIB STRUCTURAL CAPACITIES @ MAIN BOOM ANGLE (ALSO DO NOT EXCEED CAPACITIES IN ABOVE CHART)
0° 15° 30° 45° 60°
JIB STRUCTURAL CAPACITIES @ MAIN BOOM ANGLE (ALSO DO NOT EXCEED CAPACITIES IN ABOVE CHART)
1. The rated loads are the maximum lifting capacities as
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
11
YB4400
Seri
es
YB4409-2
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
dimensions
Retracted 13’ 10” & Extended 32’ 10”(Retracted 4.22 m & Extended 10.01 m)
11’ 7.75”(3.5 m)
11’ 5.5”(3.39 m)
4’ 4”(1.32 m)
15.5”(394 m)
2’ 2”(0.51 m)
1’ 0”(0.30 m)
3’ 4.5”(1.00 m)
5’ 8.38”(1.74 m)
11’ 11.75”(3.65 m)
1’ 0”(0.30 m)
5’7”(1.70 m)
1’ 6”(0.46 m)
5’ 8.38”(1.74 m)
5’ 6.92”(1.70 m)
5’ 11.88”(1.74 m)
6’ 5”(1.96 m)
7’ 3”(2.21 m)
5’ 9.7”(1.77 m)
10”
5’ 3”(1.60 m)
9’ 2.75”(1.81 m)
10’ 2”(3.10 m)
2.5”(6.35 cm)
3’ 4.5”(1.03 m)
3’ 2.5”(.98 m)
30°
54.0”(*1.37 m)
53.0”(1.34 m)
43.5”(1.10 m)
0°*0° boom headposition can onlybe used with adown haul block
80°
Dimensions are with boom horizontaland the anti-two block bottomed.
See Insert
Dimensions are withboom horizontaland the anti-twoblock bottomed.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
13
YB4400
Seri
es
load chart
YB4409-2
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
14
YB4400
Seri
es
dimensions
11' - 7.75"(3.55 m)
YB4411 Dimensions
(1346 mm)53"
30o
(1105 mm)
43.5"80o
(1372 mm)
*54"0o
SEE
INSET
*0o boomhead position can only
be used with headache ball.
Dimensions are with the boom horizontal
and the anti-two block bottomed.
11' - 7.75"(3.55 m)
YB4411 Dimensions
(1346 mm)53"
30o
(1105 mm)
43.5"80o
(1372 mm)
*54"0o
SEE
INSET
*0o boomhead position can only
be used with headache ball.
Dimensions are with the boom horizontal
and the anti-two block bottomed.
YB4411
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
15
YB4400
Seri
es
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
WIRE ROPE: 9/16 inch diameterMin. breaking strength 36750 lbs.
RATING CHARTS AND DISREGARD OF INSTRUCTIONSIS DANGEROUS AND VOIDS WARRANTY .
OPERATION OF THIS EQUIPMENT IN EXCESS OF
REDUCTION CHART
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
140 lbs
100 lbs
0 lbs
450 lbs
N/A
100 lbs
N/A
0 lbs
The rated loads are the maximum lift
capacities as determined by operating
radius, boom extension and boom
angle. The operating radius is the
horizontal distance from a projection
of the axis of rotation to the
supporting surface, before loading, to
the center of vertical hoist line or
tackle with load applied.
The rated loads shown on outriggers
do not exceed 85% of actual tipping.
The rated loads shown on rubber do
not exceed 75% of actual tipping.
These ratings are based on freely
suspended loads with the crane
leveled, standing on a firm, uniform
supporting surface. Practical working
loads depend on supporting surface,
operating radius and other factors
affecting stability. Hazardous
surroundings, climatic conditions,
experience of personnel and proper
training must all be taken into account
by the operator.
The weights of all load handling
devices such as hooks, hook blocks,
slings, etc., except the hoist rope,
shall be considered as part of the
load. See reduction chart.
1)
Ratings on rubber depend on tire
capacity, condition of tires and proper
inflation pressure (100 psi). Loads on
rubber may be transported at a
maximum speed of 2.5 mph on a
smooth hard level surface with boom
retracted to the shortest length
possible and centered over front.
For operating radius not shown, use
load rating of next larger radius.
The maximum combined total boom
and deck load is 12000 lbs. The
maximum deck load only is 14000 bs.
Do not induce any external side loads
to boom or jib.
5)
6)
7)
8)
2)
3)
Ratings on outrigggers are for either
outriggers fully extended and down or
fully retracted and down. Ratings for
outriggers fully retracted and down
will apply for any intermediate
outrigger setting.
4)
210004.0
BOOM
ON OUTRIGGERS (lbs)
MA
INB
OO
MJI
B
BOOM
(deg)ANGLE
MAINRADIUS
(ft)
RETRACTED
5.0 18000
6.0 15700
8.0 12200
10.0 10200
12.0 8400
14.0
16.0
18.0
20.0
22.0
24.0
26.0
28.0
31.0
34.0
36.0
38.0
40.0
48.0
46.0
44.0
42.0
15000
14700
14400
12200
10200
4300
2900
2600
3300
3700
6000
5000
7100
8400
41006100
12002000
8001300
1150 700
1500
1700 1050
950
20002900
2400 1600
3600
4600 3000
2400
360
940011500
8100
10000
5900
7800
11500 11500
ON RUBBER (lbs)
F/R
-
-
-
-
-
-
-
-
1200
1000
1100
1575
1425
1300
1975
1775
2300 900 500
-
-
-
-
-
-
-
-
RETRACTED F/REXTENDED 360o
EXTENDEDBOOM
21000
18000
15000
14700
375
300
325
625
525
425
850
750
6700
2100
1300
1150
1000
1800
1500
3100
2600
3800
5000
14400
9400
-
-
-
-
-
-
-
-
6700
-
-
-
-
-
-
-
-
-
5000
14400
9400
RETRACTED 360o 12 FTJIB
0OFFSET
2800
3500
1600
1300
1200
2300
7500
5700
4500
72
55
30
0
15
45
50
60
65
OFFSET15
3000
1500
1300
-
2500
2200
5100
4100
3500
OFFSET30
2550
1400
-
-
2300
2000
3500
3100
2800
OFFSET0
2450
1400
1100
1000
2150
1900
4000
3200
2800
OFFSET15
2150
1300
1100
-
1950
1750
3300
2700
2400
OFFSET30
1700
1300
-
-
1600
1500
2300
2000
1850
18 FTJIB
70 7000 4800 3400 3750 3100 2200
40 2000 1900 1800 1700 1600 1400
35 1775 1675 1600 1525 1450 1350
EXTENDEDBOOM
RETRACTEDBOOM ANY
BOOMANY
BOOM
20 13501350 - 1175 1125 -
25 1450 1400 - 1275 1200 -
10
5
1275
1225
-
-
-
- 1025
1050 -
-
-
-
700
600
500
425
350
300
275
250
350
275
200
125
75
0
0
0
-
JIB CAPACITY IS LIMITED BY BOTH STRUCTURALCAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURALSTRENGTH, DO NOT RELY ON TIPPING.
JIB STRUCTURAL CAPACITIES (lbs)
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
YB4411
17
YB4400
Seri
es
1.5
0
3.0
4.6
6.1
7.6
3S
EC
TIO
N
4S
EC
TIO
N
9.1
10.7
12.2
45o
30o
60o
0o
15o
3.0 1.5 0 1.5 3.0 4.6 6.1 7.6 9.1 10.7
1.8m
JIB
3.0 1.5 0 1.5 3.0 4.6 6.1 7.6 9.1 10.7
1.5
0
3.0
4.6
6.1
7.6
9.1
10.7
12.2
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
range diagramH
EIG
HT
FR
OM
GR
OU
ND
INM
ET
ER
S
OPERATING RADIUS IN METERS FROM AXIS OF ROTATION
YB4409
DIN/ISOload chart
18
YB4400
Seri
es
ON RUBBER (kg)ON OUTRIGGERS (kg)
MA
INB
OO
MJI
B
77101.5
RADIUS(m)
1.8 7120
2.4 5620
3.0 4630
3.7 3860
4.3 3270
4.9
5.5
6.1
6.7
7.5
7.9
8.5
9.1
9.4
7710
6530
4900
3900
3000
1120
-
-
-
930
1470
1220
1800
2250
- -
1000
-
-
2100
1220
1180
2580
-
4540
4540
4380
3260
950
340
-
-
-
260
-
460
400
570
730
1970
1300
1520
590
-
-
-
480
-
770
670
930
1160
3200
2080
F/R 360o F/R 360o
3-SECTION BOOM OR4-SECTION BOOM WITH 4TH RETRACTED
ON RUBBER (kg)ON OUTRIGGERS (kg)
2770
RADIUS(m)
2770
2400
2130
2000
2000
2770
2770
2400
2130
2000
1110
780
690
870
940
1720
1310
2000
2000
920 660
1290
1080
1190
2000
1800
1540
2000
970
2770
2770
2770
2770
1080
340
210
170
150
270
250
510
420
650
820
2380
1560
1660
590
410
330
350
500
460
820
690
1010
1280
2400
2130
F/R 360o F/R 360o
4-SECTION BOOM WITH 4TH EXTENDED
BOOM
(deg)ANGLE
MAIN
4-SECTION BOOM
60
40
15
0
30
35
45
50
1305
1090
1000
1270
1225
1590
1430
1360
4-SECTION BOOM
JIB STRUCTURAL CAPACITIES (kg)
55 1510
25 1180
20 1135
5 1020
10 1055
JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL
3-SECTION BOOM OR
WITH 4TH RETRACTEDWITH 4TH EXTENDED
1304
1089
998
1270
1225
1588
1429
1361
1508
1179
1134
1021
1055
LIMIT RATINGS TO 5 350 kg WHEN 3RD SECTION IS EXTENDED ANY AMOUNT.*
0-7710 kg2-PART
0-3855 kg1-PART
RIGGING CHART
WIRE ROPE: 13mm diameter
Min. breaking strength 139.8 kN
REDUCTION CHART
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
64 kg
45 kg
0 kg
68 kg
N/A
45 kg
N/A
0 kg
1.5
1.8
2.4
3.0
3.7
4.3
4.9
5.5
6.1
6.7
7.5
7.9
8.5
9.1
9.4
FRONT REAR
SIDE
SIDE
15o
30o
15o
30o
SHADED AREAS ARE GOVERNED BY STRUCTURALSTRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OFRATING CHARTS AND DISREGARD OF INSTRUCTIONSIS DANGEROUS AND VOIDS WARRANTY.
CAPACITY CHART AND MAIN CAPACITY CHART.
1) The rated loads are the maximumlifting capacities as determined by operating radius only. Anycombination of boom lengths and angles may be used to obtainoperating radius. The operating radius is the horizontal distance from a projection of the axis ofrotation to the supporting surface,before loading, to the center ofvertical hoist line or tackle withload applied.
2) The rated loads shown on outriggers do not exceed 80% ofactual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniformsupporting surface. Practicalworking loads depend on supporting surface, operating radiusand other factors affecting stability.Hazardous suroundings, climatic conditions, experience of operatorand proper training must be takeninto account by the operator.
3) The weights of all load handlingdevices, such as hooks, hookblocks, slings, etc., except the hoistrope, shall be considered as partof the load. See reduction chart.
4) Ratings on outriggers are withoutriggers fully extended.
5) Ratings on rubber depend on tirecapacity, condition of tires andproper inflation pressure (6.9 bar).Loads on rubber may be transported at a maximum speedof 4 km/h on a smooth, hard, levelsurface with the boom retracted tothe shortest length possible and centered over the front.
6) For operating radius not shown, useload rating of next larger radius.
7) The maximum combined totalboom and deck load is 5 440 kgs.The maximum deck load only is 6 350 kgs.
8) Do not induce any external sideloads to boom or jib.
The
rated
loads
are the
maximum
lifting
capacities
as
determined
by
operating
radius
only.
Any
combination
of
boom
lengths
and
angles
may be
used to
obtain
operating
radius.
The
operating
radius is
the
horizontal
distance
from a
projection
of the
axis of
rotation
to the
supporting
surface,
before
loading,
to the
center
of
vertical
hoist line
or
tackle
with load
applied.
The
rated
loads
shown
on
outriggers
do not
exceed
80 of
actual
tipping.
The
rated
loads
shown
on
rubber
do not
exceed
75 of
actual
tipping.
These
ratings
are
based
on
freely
suspended
loads
with the
crane
leveled,
standing
on a
firm,
uniform
supporting
surface.
Practical
working
loads
depend
on
supporting
surface,
operating
radius
and
other
factors
affecting
stability.
Hazardous
surroundings,
climatic
conditions,
experience
of
personnel
and
training
must all
be
into
account
by the
operator.
The
weights
of all
load
handling
devices
such as
hooks,
YB4409
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
19
YB4400
Seri
es
YB4409XL
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
range diagram
10.7
1.5
3.00
1.5
3.0
4.6
6.1
7.6
3S
EC
TIO
N
4S
EC
TIO
N
1.50 4.63.0 7.66.1 9.1
9.1
10.7
12.2
13.7
45o
30o
60o
12.2
0o
1515oo
013.7
1.8m
JIB
15.210.73.0 1.5 1.50 4.63.0 7.66.1 9.1 12.2 13.7
1.5
3.0
4.6
6.1
7.6
9.1
10.7
12.2
13.7
15.2
HE
IGH
TF
RO
MG
RO
UN
DIN
ME
TE
RS
OPERATING RADIUS IN METERS FROM AXIS OF ROTATION
YB4409XL
20
YB4400
Seri
es
YB4409XL
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
DIN/ISOload chart
1) The rated loads are the maximumlifting capacities as determined by operating radius only. Anycombination of boom lengths and angles may be used to obtainoperating radius. The operating radius is the horizontal distance from a projection of the axis ofrotation to the supporting surface,before loading, to the center ofvertical hoist line or tackle withload applied.
2) The rated loads shown on outriggers do not exceed 80% ofactual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniformsupporting surface. Practicalworking loads depend on supporting surface, operating radiusand other factors affecting stability.Hazardous suroundings, climatic conditions, experience of operatorand proper training must be takeninto account by the operator.
3) The weights of all load handlingdevices, such as hooks, hookblocks, slings, etc., except the hoistrope, shall be considered as partof the load. See reduction chart.
4) Ratings on outriggers are withoutriggers fully extended.
5) Ratings on rubber depend on tirecapacity, condition of tires andproper inflation pressure (6.9 bar).Loads on rubber may be transported at a maximum speedof 4 km/h on a smooth, hard, levelsurface with the boom retracted tothe shortest length possible and centered over the front.
6) For operating radius not shown, useload rating of next larger radius.
7) The maximum combined totalboom and deck load is 5 443 kgs.The maximum deck load only is 6 350 kgs.
8) Do not induce any external sideloads to boom or jib.
0-7710 kg2-PART
0-3855 kg1-PART
RIGGING CHART
WIRE ROPE: 13mm diameter
Min. breaking strength 139.8 kN
REDUCTION CHART
MA
INB
OO
MJI
B
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
64 kg
45 kg
0 kg
68 kg
N/A
45 kg
N/A
0 kg
771071205625462538553220
77106530490038553150
1100
770730
820950
15701290
19302550
970880
---- -
---
580530
650
1360
11201180
236018501570
2720
1070
45354310
45353720
-
---
9060
1170
310
170140110
240190
470380
610830
24901670
-
---
240220
1670
540
340
280310
450370
770630
9301200
35802400
800
F/R 360o F/R 360o
- - --
3-SECTION BOOM OR4-SECTION BOOM WITH 4TH RETRACTED
SHADED AREAS ARE GOVERNED BY STRUCTURALSTRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OFRATING CHARTS AND DISREGARD OF INSTRUCTIONSIS DANGEROUS AND VOIDS WARRANTY.
JIB CAPACITY IS LIMITED BY BOTH STRUCTURALCAPACITY CHART AND MAIN CAPACITY CHART.
21
YB4400
Seri
es
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
1) The rated loads are the maximumlift capacities as determined by operating radius, boom extension and boom angle. The operating radius is the horizontaldistance from a projection of the axis of rotation to the supporting surface,before loading, to the center ofvertical hoist line or tackle with load applied.
The rated loads shown on outriggers do not exceed 80% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface.Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account bythe operator.
2)
The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered as part of the load. See reduction chart.
Ratings on outrigggers are for outriggers fully extended.
Ratings on rubber depend on tirecapacity, condition of tires and proper inflation pressure (700 kPa). Loads on rubber may betransported at a maximum speed of 1.4 km/h on a smooth hard levelsurface with boom retracted to the shortest length possible and centered over front.
For operating radius not shown, use load rating of next larger radius.
The maximum combined total boom and deck load is 5440 kg. The maximum deck load only is 6530 kg.
Do not induce any external side loads to boom or jib.
5)
6)
7)
8)
3)
4)
FRONT REAR
SIDE
SIDE
15o
30o
15o
30o
SHADED AREAS ARE GOVERNED BY STRUCTURALSTRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OFRATING CHARTS AND DISREGARD OF INSTRUCTIONSIS DANGEROUS AND VOIDS WARRANTY.
JIB CAPACITY IS LIMITED BY BOTH STRUCTURALCAPACITY CHART AND MAIN CAPACITY CHART.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
0
15o
20o
0o
5o
10o
25o
30o
35o
40o
45o
70o
65o
60o
55o
50o
0
72o
4.2
mBO
OM
7.1
mBO
OM
10.0
mBO
OM
13.7
mBO
OM
15.5
mBO
OM
WIT
H3.
7m
JIB
WIT
H3.
7m
JIB
&1.
8m
STIN
GER
1230
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
3 2 1 31 2 4 5 6 7 8 9 10 11 12 13 14 15
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
HE
IGH
TF
RO
MG
RO
UN
DIN
ME
TE
RS
OPERATING RADIUS IN METERS FROM AXIS OF ROTATION
YB4411
23
YB4400
Seri
es
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
range diagram
0-9530 kg2-PART
0-4540 kg1-PART
RIGGING CHART
95301.2
WIRE ROPE: 14 mm diameter
Min. breaking strength 172.8 kN
SHADED AREAS ARE GOVERNED BY STRUCTURAL
OPERATION OF THIS EQUIPMENT IN EXCESS OF
REDUCTION CHART
BOOM
ON OUTRIGGERS (kg)
MA
INB
OO
MJI
B
MAIN BOOMFROM
RATINGSJIB
FROM
RATINGS
MAIN BLOCK
HOOK & BALL
JIB, STOWED
JIB, DEPLOYED
60 kg
45 kg
0 kg
200 kg
N/A
45 kg
N/A
0 kg
BOOM
(deg)ANGLE
MAINRADIUS
(m)
RETRACTED
1.5 8160
1.8 7120
2.4 5530
3.0 4630
3.7 3810
4.3
4.9
5.5
6.1
6.7
7.3
7.9
8.5
9.4
10.411.0
11.6
12.2
14.6
14.0
13.4
12.8
6800
6670
6530
5530
4630
1790
1190
1060
1360
1530
2720
2270
3220
3810
18102720
540860
320540
480 270
630
730 430
380
8201270
1040 680
1590
2040 1310
1040
360o
42605220
3670
4540
2680
3540
5220 5220
ON RUBBER (kg)
F/R
-
-
-
-
-
-
-
-
460
380
420
620
560
510
790
710
930 360 180
-
-
-
-
-
-
-
-
RETRACTED F/REXTENDED 360o
EXTENDEDBOOM
9530
8160
6800
6670
110
80
90
220
180
130
310
270
2810
850
510
440
380
720
590
1270
1060
1570
2090
6530
3960
-
-
-
-
-
-
-
-
2810
-
-
-
-
-
-
-
-
-
2090
6530
3960
RETRACTED 360o 3.7 m JIB
0o
OFFSET
1270
1590
730
590
540
1040
3400
2590
2040
72
55
30
0
15
45
50
60
65
OFFSET15o
1360
680
590
-
1130
1000
2310
1860
1590
OFFSET30o
1160
640
-
-
1040
910
1590
1410
1270
OFFSET0o
1110
640
500
450
980
860
1810
1450
1270
OFFSET15o
980
590
500
-
880
790
1500
1220
1090
OFFSET30o
770
590
-
-
730
680
1040
910
840
5.5 m JIB
JIB STRUCTURAL CAPACITIES (kg)
70 3180 2180 1540 1700 1410 1000
40 910 860 820 770 730 640
35 810 760 730 690 660 610
EXTENDEDBOOM
RETRACTEDBOOM ANY
BOOMANY
BOOM
20 610610 - 530 510 -
25 660 640 - 580 540 -
10
5
580
560
-
-
-
- 460
480 -
-
-
-
270
230
180
150
110
90
80
70
110
80
40
10
0
0
0
0
-
JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL
FRONT REAR
SIDE
SIDE
STRENGTH, DO NOT RELY ON TIPPING.
RATING CHARTS AND DISREGARD OF INSTRUCTIONS
15o
30o
15o
30o
IS DANGEROUS AND VOIDS WARRANTY.
CAPACITY CHART AND MAIN CAPACITY CHART.
4)
5)
6)
7)
8)
Ratings on outriggers are withoutriggers fully extended.
Ratings on rubber depend on tirecapacity, condition of tires and proper inflation pressure (6.9 bar).Loads on rubber may be transported at a maximum speed of4 km/h on a smooth, hard, level surface with the boom retracted to the shortest length possible and centered over the front.
For operating radius not shown, use load rating of next larger radius.
The maximum combined total boom and deck load is 5 440 kgs. The maximum deck load only is 6 350kgs.
Do not induce any external side loads to boom or jib.
1)
2)
3)
The rated loads are the maximum lifting capacities as determined by operating radius only. Any combination of boom lengths and angles may be used to obtain operating radius. The operatingradius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with loadapplied.
The rated loads shown on outriggers do not exceed 80% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operatingradius and other factors affecting stability. Hazardous suroundings,climatic conditions, experience of operator and proper training must be taken into account by the operator.
The weights of all load handlingdevices, such as hooks, hookblocks, slings, etc., except thehoist rope, shall be considered as part of the load. See reduction chart.
24
YB4400
Seri
es
YB4411
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions andother instructional plates must be read and understood prior to operating the crane.
DIN/ISOload chart
25
YB4400
Seri
es
notes
notes
26
YB4400
Seri
es
27
YB4400
Seri
es
notes
Constant improvement and engineering progressmake it necessary that we reserve the right to makespecification, equipment and price changes withoutnotice. Illustrations shown may include optionalequipment and accessories, and may not include allstandard equipment.