7/23/2019 XW NAS3 Operating Instructions
1/60
Operating InstructionsMode demploi
Manual de instrucciones
Register your product on
http://www.pioneerelectronics.com (US)http://www.pioneerelectronics.ca (Canada)
http://www.pioneerelectronics.com (US)
http://www.pioneerelectronics.ca (Canada)
Protect your new investmentThe details of your purchase will be on file for reference in the event of an insurance claim such as loss or theft.
Improve product developmentYour input helps us continue to design products that meet your needs.
Receive a free Pioneer newsletterRegistered customers can opt in to receive a monthly newsletter.
Receive free tips, updates and service bulletins on your new product
XW-NAS3Digital Speaker System for iPodStation daccueil audio numrique pour iPod
Sistema digital de parlantes para iPod
7/23/2019 XW NAS3 Operating Instructions
2/60
IMPORTANT NOTICETHE MODEL NUMBER AND SERIAL NUMBER OF THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON YOUR ENCLOSED WARRANTY CARD AND KEEP IN A SAFE PLACE FOR FUTURE
REFERENCE.D36-AP9-1_A1_En
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.D8-10-1-2_A1_En
This Class B digital apparatus complies withCanadian ICES-003.
D8-10-1-3_A1_En
Information to UserAlterations or modifications carried out without
appropriate authorization may invalidate the users
right to operate the equipment.D8-10-2_A1_En
CAUTION
This product satisfies FCC regulations when shieldedcables and connectors are used to connect the unit
to other equipment. To prevent electromagnetic
interference with electric appliances such as radios
and televisions, use shielded cables and connectors
for connections.D8-10-3a_A1_En
WARNING: Handling the cord on this product orcords associated with accessories sold with the
product may expose you to chemicals listed on
proposition 65 known to the State of California and
other governmental entities to cause cancer andbirth defect or other reproductive harm.
Wash hands aft er handling.D36-P5_B1_En
WARNINGThis equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.D3-4-2-1-3_A1_En
WARNINGTo prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.D3-4-2-1-7a_A1_En
WARNINGBefore plugging in for the first time, read the followingsection carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
or 120 V) written on the bottom panel.D3-4-2-1-4*_A1_En
VENTILATION CAUTIONWhen installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 20 cm at top, 10 cm at rear, and 10 cm at each
side).
WARNINGSlots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.D3-4-2-1-7b*_A1_En
Operating EnvironmentOperating environment temperature and humidity:
+5 C to +35 C (+41 F to +95 F); less than 85 %RH
(cooling vents not blocked)Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)D3-4-2-1-7c*_A1_En
7/23/2019 XW NAS3 Operating Instructions
3/60
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
dangerous voltage within the products
enclosure that may be of sufficientmagnitude to constitute a risk of electric
shock to persons.
CAUTION:TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIEDSERVICE PERSONNEL.
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT
D3-4-2-1-1_A1_En
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturers
instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the thirdprong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Only use attachments/accessories specified by
the manufacturer.
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms
or when unused for long periods of time.
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus hasbeen damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
D3-7-13-69_En
11)
12)
13)
14)
CAUTIONThe STANDBY/ONswitchonthisunitwillnotcompletelyshutoffallpowerfromtheACoutlet.
Sincethepowercordservesasthemaindisconnect
devicefortheunit,youwillneedtounplugitfromthe
ACoutlettoshutdownallpower.Therefore,make
suretheunithasbeeninstalledsothatthepower
cordcanbeeasilyunpluggedfromtheACoutletin
caseofanaccident.Toavoidfirehazard,thepower
cordshouldalsobeunpluggedfromtheACoutlet
whenleftunusedforalongperiodoftime(for
example,whenonvacation). D3-4-2-2-2a*_A1_En
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in arestaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.K041_A1_En
IftheACplugofthisunitdoesnotmatchtheAC
outletyouwanttouse,theplugmustberemoved
andappropriateonefitted.Replacementand
mountingofanACplugonthepowersupplycordof
thisunitshouldbeperformedonlybyqualified
servicepersonnel.IfconnectedtoanACoutlet,the
cut-offplugcancausesevereelectricalshock.Make
sureitisproperlydisposedofafterremoval.
Theequipmentshouldbedisconnectedbyremoving
themainsplugfromthewallsocketwhenleftunused
foralongperiodoftime(forexample,whenon
vacation).D3-4-2-2-1a_A1_En
These symbols are only valid
in the European Union.
K058c_A1_En
(Symbol examples for batteries)
Pb
7/23/2019 XW NAS3 Operating Instructions
4/60
POWER-CORD CAUTIONHandle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find itdamaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.S002*_A1_En
Thisproductcontainsmercury.Disposalofthis
materialmayberegulatedduetoenvironmental
considerations.Fordisposalorrecycling
information,pleasecontactyourlocalauthoritiesor
theElectronicsIndustriesAlliance: www.eiae.org.
K057_A1_En
When using this product, confirm the safety
information shown on the bottom of the unit.D3-4-2-2-4_B1_En
The Safety of Your Ears is in Your HandsGet the most out of your equipment by playing it at a
safe level a level that lets the sound come through
clearly without annoying blaring or distortion and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time, your hearing
comfort level adapts to higher volumes of sound, so
what sounds normal can actually be loud and
harmful to your hearing. Guard against this by setting
your equipment at a safe level BEFORE your hearing
adapts.
ESTABLISH A SAFE LEVEL:Set your volume control at a low setting.
Slowly increase the sound until you can hear it
comfortably and clearly, without distortion.
Once you have established a comfortable sound
level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWINGGUIDELINES:
Do not turn up the volume so high that you cant
hear whats around you.
Use caution or temporarily discontinue use in
potentially hazardous situations.
Do not use headphones while operating a motorized
vehicle; the use of headphones may create a traffic
hazard and is illegal in many areas.S001a_A1_En
7/23/2019 XW NAS3 Operating Instructions
5/60
5En
English
Franais
Deutsch
Nederlands
Italiano
Espaol
Thank you for buying this Pioneer product.Please read through these operating instructions so that you will know how to operate your modelproperly. After you have finished reading the instructions, put them in a safe place for futurereference.
Contents01 Before you startWhats in the box . . . . . . . . . . . . . . . . . . . . . . .6Before using the remote control. . . . . . . . . . . .6
Replace the battery . . . . . . . . . . . . . . . . . . . . .6Using the remote control . . . . . . . . . . . . . . . .7
Installing the unit . . . . . . . . . . . . . . . . . . . . . . .7Plugging in. . . . . . . . . . . . . . . . . . . . . . . . . . . .7
02 Controls and displaysRemote control. . . . . . . . . . . . . . . . . . . . . . . . .8Front /top panel . . . . . . . . . . . . . . . . . . . . . . . . .8
03 iPod playbackConfirm what iPod models are supported . . . . .9Connecting your iPod . . . . . . . . . . . . . . . . . . . .9
Connecting your TV. . . . . . . . . . . . . . . . . . . .10Playing your iPod . . . . . . . . . . . . . . . . . . . . . .11
Using the tone controls. . . . . . . . . . . . . . . . .11
04 Bluetooth ADAPTER for WirelessEnjoyment of MusicWireless music play . . . . . . . . . . . . . . . . . . . .13
Remote control operation . . . . . . . . . . . . . . .13Connecting Optional BluetoothADAPTER . . . .13Setting the PIN code . . . . . . . . . . . . . . . . . . . .14Pairing BluetoothADAPTER and Bluetoothwireless technology device . . . . . . . . . . . . . . .14Listening to Music Contents of Bluetooth
wireless technology device with Your System. . .15
05 Other connectionsConnecting auxiliary components . . . . . . . . . .16
06 Additional informationTroubleshooting . . . . . . . . . . . . . . . . . . . . . . .17Resetting the system . . . . . . . . . . . . . . . . . . . .18About iPod/iPhone . . . . . . . . . . . . . . . . . . . . .18Specifications. . . . . . . . . . . . . . . . . . . . . . . . .18Cleaning the unit . . . . . . . . . . . . . . . . . . . . . . .19
7/23/2019 XW NAS3 Operating Instructions
6/60
Before you start01
6En
Chapter 1:
Before you start
Whats in the boxPlease confirm that the following accessories
are in the box when you open it.
Remote control
Remote control holder
Lithium battery (CR2025)
Power cord
Cleaning cloth
Operating instructions (This document)
Before using the remote controlThe remote control is shipped already set in theremote control holder.
The battery supplied with this unit is stored inthe battery casing.
Remove the protective seal from thebattery casing.When you notice a decrease in the operatingrange, replace the battery (see below).
Replace the batteryWhen replacing the battery, use acommercially available Lithium CR2025battery.
1 Push the release tab to the left to openthe battery casing.
2 Pull out the battery casing.
3 Remove the battery from the casing.
4 Place a new battery in the casing.Make sure theside of the battery is facing up
when you place it in the space provided.
Caution
When using lithium batteries, please observethe following:
There is danger of explosion if the battery is
incorrectly replaced. Make sure to replaceonly with the same or equivalent type
recommended by the manufacturer.
Dispose of used battery cells immediatelyafter replacement. Keep away from
children.
If swallowed, please contact a doctor
immediately.
Lithium batteries may present a fire orchemical burn hazard if misused. Do notdisassemble, heat above 100 C, or
incinerate.
1
1
3
2
7/23/2019 XW NAS3 Operating Instructions
7/60
Before you start 01
7En
English
Franais
Deutsch
Nederlands
Italiano
Espaol
Remove the battery if the unit isnt going to
be used for a month or more.
When disposing of used batteries, pleasecomply with governmental regulations orenvironmental public instructions rules
that apply in your country or area.
WARNINGDo not use or store batteries in direct
sunlight or other excessively hot place,
such as inside a car or near a heater. Thiscan cause batteries to leak, overheat,explode or catch fire. It can also reduce the
life or performance of batteries.
Perchlorate Material special handling may apply.See www.dtsc.ca.gov/hazardouswaste/perchlorate.(Applicable to California, U.S.A.)
Using the remote controlThe remote has a range of about 7 m (23 ft.) at
an angle of about 30 from the remote sensor.
Keep in mind the following when using the
remote control:
Make sure that there are no obstaclesbetween the remote and the remote sensor
on the unit.
Remote operation may become unreliableif strong sunlight or fluorescent light isshining on the units remote sensor.
Remote controllers for different devices
can interfere with each other. Avoid usingremotes for other equipment located close
to this unit.
Replace the batteries when you notice a falloff in the operating range of the remote.
Installing the unit When installing this unit, make sure to putit on a level and stable surface.
Dont install it on the following places:
on a color TV (the screen may distort) near a cassette deck (or close to a device thatgives off a magnetic field). This may interfere
with the sound. in direct sunlight
in damp or wet areas
in extremely hot or cold areas in places where there is vibration or other
movement
in places that are very dusty in places that have hot fumes or oils (such asa kitchen)
Plugging inAfter youve finished making all connections,plug the unit into an AC outlet.
1 Plug the supplied power cord into the ACINsocket on the back of the unit.
2 Plug the other end into a power outlet.
Important
Before making or changing anyconnections, switch off the power and
disconnect the power cord from the ACoutlet.
30
30
7 m (23 ft.)
AUDIO IN
AC IN
7/23/2019 XW NAS3 Operating Instructions
8/60
Controls and displays02
8En
Chapter 2:
Controls and displays
Remote control
1 STANDBY/ONSwitches the unit between standby and on.
2 INPUT
Use to select an input source. Press repeatedlyto switch between iPod, Bluetooth ADAPTER1and external input.
3 VOLUME +/Use to set the listening volume.
4 Playback control buttonsUse when operating an iPod or Bluetooth
wireless technology device with this remotecontrol (page 11, 15).
Front /top panel1 Speaker units
2 iPod connector port
3 STANDBY/ONSwitches the unit between standby and on.
4 Power indicator
5 INPUT SELECTORUse to select an input source. Press repeatedlyto switch between iPod, Bluetooth ADAPTER1and external input.
6 VOLUME +/Use to set the listening volume.
7 BluetoothADAPTER indicator
8 Remote sensor
9 iPod indicator
STANDBY/ON
INPUT
VOLUME
1 3
42
Note
1 When the BluetoothADAPTER is not plugged in the ADAPTER PORT, BluetoothADAPTER input mode cannot be selected evenif INPUTis pressed.
1 2
9
8
7
STANDBY/ON INPUT SELECTOR
VOLUME
3 4 5 6
7/23/2019 XW NAS3 Operating Instructions
9/60
iPod playback 03
9En
English
Franais
Deutsch
Nederlands
Italiano
Espaol
Chapter 3:
iPod playbackMerely by connecting your iPod to this speakersystem, you can enjoy high-quality digital
sound direct from your iPod. These speakers
can also be connected to a television set,letting you view images from your iPod.
Playback and volume level setting for iPod
music and images can be performed from thisunit or the iPod itself.
Confirm what iPod models aresupportedThis system is compatible with the audio andvideo of the iPod nano third generation and
above, iPod classic, iPod touch and iPhone. It
also supports audio playback on the iPod nanosecond generation.1
Always use the most recent version of iPodsoftware available. Operation compatibilitymay vary depending on the version of thesoftware used. You can confirm your software
version by operating your iPod as follows:
1 Select Settings from the top menu.
2 Select About.The software version will be displayed.
Consult the Apple website regarding the
newest software versions and instructionson how to update your version.
Tip
When using an iPod not supported by thisunit, use a commercially available cable to
connect the iPod to the AUDIO IN
connector of this unit.
Connecting your iPod
Caution
To prevent damage when connecting an
iPod, always use the Dock adaptorsupplied with your iPod, or a commerciallypurchased Dock adaptor designed for your
iPod model.
Note
1 Some functions may be restricted depending on the model or software version. iPod is licensed for reproduction of non-copyrighted materials or materials the user is legally permitted to reproduce. Features such as the equalizer cannot be controlled using this system, and we recommend switching the equalizeroff before connecting.
Pioneer cannot under any circumstances accept responsibility for any direct or indirect loss arising from anyinconvenience or loss of recorded material resulting from the iPod failure. When connecting an iPod, use the Speaker menus Backlight item to set the iPods backlight function. This doesnot apply to iPod touch.
MENU
iPod
Dock adaptor
7/23/2019 XW NAS3 Operating Instructions
10/60
iPod playback03
10En
1 Attach the Dock adaptor to iPodconnector port on the top panel of this unit.
An iPod Dock adaptor is not supplied withthis unit.
When attaching the Dock adaptor, be sure to
orient the front-back directions of the Dockadaptor correctly. To attach, first place the
protruding tabs on the front side of the adaptorinto the depressions on the iPod connectorport and press into position. When attaching
the adaptor, be careful not to strike the
connectors.
2 Connect your iPod.
Connecting your TVTo watch iPod images on a television, perform
connections using either a composite videocable or component video cable.
When using a component video cable for
connections, it is necessary to adjust theunits video output. SeeSetting the video
outputbelow. When an iPod is connected to this unit, the
iPods TV output setting is automatically
set to ON. While connected, the iPod canbe used to switch the TV output setting.1
Caution
Before making or changing theconnections, switch off the power and
disconnect the power cord from the poweroutlet. Plugging in should be the final step.
Setting the video outputAdjust the video output on this unit in
accordance with the method used to connectthe television.2
Default setting: Composite
1 Switch the unit into standby.
2 Press and hold INPUT on the remotecontrol for three seconds.The iPod indicator will flash two times, and the
video output will switch to Component. When
step 2 is repeated again, the iPod indicator willflash one time, and the video output will switch
to Composite.
Note
1 This function is limited to iPod models providing TV output settings.
When the iPod is disconnected from this unit, the iPods TV output setting returns to its original state.2 Stop the iPods video playback before adjusting the video output setting. The setting mode is disabled during playback and
pause. During the video output setting process, if no button operation is performed for 3 minutes, the setting will be canceled andpower will return to the standby mode.
COMPONENT VIDEO
MONITOR OUT VIDEO 1VIDEO 2
ADAPTER PORT
Y PB PR AUDIO IN
TV
Componentvideo cable
(commerciallyavailable)
Compositevideo cable
(commerciallyavailable)
INPUT
7/23/2019 XW NAS3 Operating Instructions
11/60
iPod playback 03
11En
English
Franais
Deutsch
Nederlands
Italiano
Espaol
Playing your iPod
Caution
When your iPod is connected to this unit
and you wish to operate the iPod bytouching it directly, be sure to hold the iPod
steady with the other hand to preventmalfunctions due to faulty contacts.
When an iPod is connected to this unit, iPod
indicator will flash while the unit confirms the
iPod connection and retrieves data from theiPod. When INPUTis pressed to change theinput to iPod, the connection is completed andiPod indicator will light steadily.1
Playback and volume level setting for iPodmusic and images can be performed from this
unit or the iPod itself.
When using the iPod to adjust soundvolume, the adjustment will be applied only
to the sound produced from this unitsspeakers.2If the iPod is disconnected fromthis unit, the iPods sound volume willreturn to its original setting.
The following operations are possible for iPod,
using the remote control.
Using the tone controlsAdjust the sound tone. Adjustment is
performed from the iPods screen.2Thesettings performed here are reflected in theBASS/TREBLE settings on this unit.
iPod nano or iPod classic:
1 Select Speaker from the top menu.
2 Select Tone control.
3 Select a setting.
iPod touch or iPhone:
3
1 Select Settings from the home menu.
2 Select Speaker.
3 Select Tone control.
4 Select a setting.
Select one of the following:
Flat Revert sound to its natural state.
Bass ON Emphasize bass sound.
Treble ON Emphasize treble sound.
Bass/Treble ON Emphasizes bass andtreble sounds.
Note1 If an iPod is connected when this unit is in standby mode, the power will turn on and iPod input will be selected automatically.2 These adjustments are applied to all inputs to the unit.
Button What it does
/ Starts normal playback and pauses/
unpauses playback.
Press to skip to the start of the currentfile, then previous files. Press and hold
to start fast reverse scanning.
Press to skip to the next file. Press and
hold to start fast forward scanning.
VOLUME
+/Use to set the listening volume.
3 This setting may not be supported, depending on the iPod touch or iPhone software version.
7/23/2019 XW NAS3 Operating Instructions
12/60
iPod playback03
12En
Important
If the power indicator and iPod indicator flash
simultaneously, a connection fault is
indicated. Perform the followingtroubleshooting checks:
Check whether the iPod was supported by
this unit.
Reconnect the iPod to the unit. If this
doesnt seem to work, try resetting youriPod.
Update the iPod software to the latestversion.
If the iPod cannot be operated, check the
following items:
Is the iPod connected correctly?Reconnect the iPod to the unit.
Is the iPod experiencing a hangup? Tryresetting the iPod, and reconnect it to the
unit.
Tip
iPod recharging occurs whenever an iPod
is connected to this unit. (This function issupported in standby mode as well.)
Whenever an iPod is connected to this
unit, turning the units power ON orswitching input to iPod will cause iPodplayback to begin automatically.
When input is switched from iPod to
another function, the iPod playback stops
automatically.
If the unit is set to standby when an iPod isconnected, the iPods power will be turnedOFF automatically.
7/23/2019 XW NAS3 Operating Instructions
13/60
Bluetooth ADAPTER for Wireless Enjoyment of Music 04
13En
English
Franais
Deutsch
Nederlands
Italiano
Espaol
Chapter 4:
BluetoothADAPTER forWireless Enjoyment of Music
Wireless music playWhen the BluetoothADAPTER (Pioneer ModelNo. AS-BT100) is connected to this unit, aproduct equipped with Bluetoothwirelesstechnology (portable cell phone, digital musicplayer, etc.) can be used to listen to musicwirelessly.1Also, by using a commerciallyavailable transmitter supporting Bluetoothwireless technology, you can listen to music on
a device not equipped with Bluetoothwirelesstechnology. The AS-BT100 model supportsSCMS-T contents protection, so music canalso be enjoyed on devices equipped withSCMS-T type Bluetoothwireless technology.
Remote control operationThe remote control supplied with this unitallows you to play and stop media, and performother operations.2
Connecting Optional BluetoothADAPTER
Before making or changing theconnections, switch off the power anddisconnect the power cord from the AC
outlet.
Remote control operation
This unit
Bluetooth
ADAPTER
Device not equipped withBluetooth wireless technology:Digital music player
+Bluetoothaudio transmitter (soldcommercially)
Bluetooth wireless technologyenabled device:Digital music player
Bluetooth wirelesstechnology enabled device:Cell phone
Note
1 It must be necessary that the Bluetoothwireless technology enabled device supports A2DP profiles. Pioneer does not guarantee proper connection and operation of this unit with all Bluetoothwireless technology enabled devices.
2 It must be necessary that the Bluetoothwireless technology enabled device supports AVRCP profiles. Remote control operations cannot be guaranteed for all Bluetoothwireless technology enabled devices.
COMPONENT VIDEO
MONITOR OUT VIDEO 1VIDEO 2
ADAPTER PORT
Y PB PR
Bluetooth
ADAPTER
7/23/2019 XW NAS3 Operating Instructions
14/60
Bluetooth ADAPTER for Wireless Enjoyment of Music04
14En
1 Switch the unit into standby and connectBluetoothADAPTER to the ADAPTER PORTlocated in the rear panel.
2 PressSTANDBY/ON.
3 Press INPUTto switch to BluetoothADAPTER input mode.1
The BluetoothADAPTER indicator blinks.
Setting the PIN codeSet this units PIN code to the same setting as
that for the Bluetoothwireless technologydevice used. Supported PIN code settingvalues include 0000, 1234 or 8888.
Default setting: 0000
1 Switch the unit into standby.
2 Press and holdfor three seconds.The BluetoothADAPTER indicator will flash,
and the PIN code will be changed. The number
of flashes corresponds to the newly set PINcode as follows:
1 flash: 0000
2 flashes: 1234
3 flashes: 8888
Repeat step 2 until the PIN code is reset to the
value desired.
Pairing BluetoothADAPTER andBluetooth wireless technologydevicePairing must be done before you start
playback of Bluetoothwireless technologycontent using BluetoothADAPTER. Make sureto perform pairing first time you operate the
system or any time pairing data is cleared.
Pairing is the step necessary to registerBluetoothwireless technology device to enable
Bluetoothcommunications.2For more details,see also the operating instructions of yourBluetoothwireless technology device.
1 When the BluetoothADAPTER indicatorblinks, press.The BluetoothADAPTER indicator will blinks
fast, and the unit will enter the pairing standbymode.
2 Switch on the Bluetoothwirelesstechnology device that you want to makepairing, place it near the system and set itinto the pairing mode.Pairing begins.
3 Check to see that the Bluetooth ADAPTERis detected by the Bluetoothwirelesstechnology device.The BluetoothADAPTER indicator lights whenBluetoothwireless technology device is
connected.
The BluetoothADAPTER indicator blinks slowly
when Bluetooth wireless technology device isnot connected. In this case, perform theconnection operation from the side of the
Bluetoothwireless technology device.
Note
1 When the BluetoothADAPTER is not plugged in the ADAPTER PORT, BluetoothADAPTER input mode cannot be selected even
if INPUTis pressed.
INPUT
2 Pairing is required when you first use Bluetoothwireless technology device and BluetoothADAPTER. To enable Bluetoothcommunication, pairing should be done with both of your system and Bluetoothwireless technologydevice.
INPUT
7/23/2019 XW NAS3 Operating Instructions
15/60
Bluetooth ADAPTER for Wireless Enjoyment of Music 04
15En
English
Franais
Deutsch
Nederlands
Italiano
Espaol
Listening to Music Contents ofBluetoothwireless technologydevice with Your System
1 Press INPUTto switch to BluetoothADAPTER input mode.The BluetoothADAPTER indicator blinks.
2 Connect the Bluetoothwirelesstechnology device to the BluetoothADAPTER.
3 Start playback of music contents stored inBluetoothwireless technology device.The following operations are now possible for
Bluetoothwireless technology devices, usingthe remote control.1
Button What it does
/ Starts normal playback and pauses/
unpauses playback.
Press to skip to the start of the currentfile, then previous files. Press and hold
to start fast reverse scanning.
Press to skip to the next file. Press and
hold to start fast forward scanning.
VOLUME
+/Use to set the listening volume.
Note
1 Bluetoothwireless technology device should be compatible with AVRCP profile. Depending on Bluetoothwireless technology device you use, operation may differ from what is shown in this table.
7/23/2019 XW NAS3 Operating Instructions
16/60
Other connections05
16En
Chapter 5:
Other connections Before making or changing the
connections, switch off the power anddisconnect the power cord from the ACoutlet.
Connecting auxiliary
componentsConnect the rear panel AUDIO IN mini-plugjack to your auxiliary playback component.
This method can be used to play music on
this unit from iPods that do not support useof an iPod Dock.
Press INPUTto switch to external inputmode.Both the iPod indicator and the Bluetooth
ADAPTER indicator will go out.
COMPONENT VIDEO
MONITOR OUT VIDEO 1VIDEO 2
Y PB PR AUDIO IN
AC IN
Digital audio
player, etc.
7/23/2019 XW NAS3 Operating Instructions
17/60
Additional information 06
17En
English
Franais
Deutsch
Nederlands
Italiano
Espaol
Chapter 6:
Additional information
TroubleshootingIncorrect operations are often mistaken for trouble and malfunctions. If you think that there issomething wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work. If the unit does not operate normally due to external effects such as static electricity disconnect
the power plug from the outlet and insert again to return to normal operating conditions.
Problem Remedy
The power does not turn on. Disconnect the power plug from the outlet, and insert again.
If the power shuts off automatically, take the unit to your nearest
Pioneer authorized service center or your dealer for servicing.
Power automatically switches to
standby without user action.
When input is set to iPod, if no iPod is connected for one hour or more,
the units power automatically turns OFF.
No sound is output when afunction is selected.
Make sure the component is connected correctly (refer to Connectingauxiliary componentson page 16).
Cant operate the remote
control.
Replace the battery (refer to page 6).
Operate within 7 m (23 ft.), 30 of the remote sensor on the front panel
(refer to page 7).
Remove the obstacle or operate from another position.
Avoid exposing the remote sensor on the front panel to direct light.
The Bluetoothwirelesstechnology device cannot beconnected or operated. Sound
from the Bluetoothwirelesstechnology device is not emittedor the sound is interrupted.
Check that no object that emits electromagnetic waves in the 2.4 GHzband (microwave oven, wireless LAN device or Bluetoothwirelesstechnology apparatus) is near the unit. If such an object is near the unit,
set the unit far from it. Or, stop using the object emitting theelectromagnetic waves. Check that the Bluetoothwireless technology device is not too far fromthe unit and that obstructions are not set between the Bluetoothwirelesstechnology device and the unit. Set the Bluetoothwireless technologydevice and the unit so that the distance between them is less than about10 m (32 ft.) and no obstructions exist between them. Check that the BluetoothADAPTER and the ADAPTER PORTof the unitare correctly connected. The Bluetoothwireless technology device may not be set to thecommunication mode supporting the Bluetoothwireless technology.Check the setting of the Bluetoothwireless technology device. Check that pairing is correct. The pairing setting was deleted from this
unit or the Bluetoothwireless technology device. Reset the pairing. Check that the profile is correct. Use a Bluetoothwireless technologydevice that supports A2DP profile and AVRCP profile.
7/23/2019 XW NAS3 Operating Instructions
18/60
Additional information06
18
En
Resetting the systemUse this procedure to reset all system settingsto the factory default.
When performing reset, first disconnect all
components connected to this unit.
1 Switch the unit on.
2 Press and hold VOLUME on the toppanel, and then press and holdSTANDBY/ONfor three seconds.
Power is set to standby mode.The next time you switch on, all the system
settings should be reset.
About iPod/iPhone
Made for iPod and Made for iPhone mean
that an electronic accessory has beendesigned to connect specifically to iPod oriPhone, respectively, and has been certified by
the developer to meet Apple performance
standards. Apple is not responsible for theoperation of this device or its compliance with
safety and regulatory standards.iPod and iPhone are trademarks of Apple Inc.,registered in the U.S. and other countries.
Specifications Amplifier sectionRMS Power Output:
Front Left/Right . . . . . . . . . . . . . . 15 W + 15 W
(1 kHz, 10 %, T.H.D., 8 )
Subwoofer . . 30 W(100 Hz, 10 %, T.H.D., 4 )
Speaker sectionEnclosure . . . Bass-reflex (magnetically shielded)
System . . . . . . . . . . . . . . . . . . . . . . . 2-way system
Speakers:
Subwoofer . . . . . . . . . . . . . . 10 cm (4 in.) cone
Fullrange . . . . . . . . . . . . . . . 5.2 cm (2 in.) cone
Frequency range . . . . . . . . . . . . . 50 Hz to 20 kHz
MiscellaneousPower requirements
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .AC 120 V/60 Hz
Power consumption . . . . . . . . . . . . . . . . . . . 30 W
In standby. . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 W
Dimensions
. . . . . . . 420 mm (W) x 148 mm (H) x 210 mm (D)
(16 9/16in. (W) x 5 7/8in. (H) x 8 5/16in. (D))Weight (without package). . . . . . . 4.9 kg (10.8 lb)
AccessoriesRemote control . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Remote control holder. . . . . . . . . . . . . . . . . . . . . .1
Lithium battery (CR2025) . . . . . . . . . . . . . . . . . . .1
Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Cleaning cloth . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Operating instructions (This document)
Note
Specifications and the design are subject
to possible modifications without notice,due to improvements.
7/23/2019 XW NAS3 Operating Instructions
19/60
Additional information 06
19En
English
Franais
Deutsch
Nederlands
Italiano
Espaol
Cleaning the unit Use a polishing cloth or dry cloth to wipeoff dust and dirt.
When the surface is dirty, wipe with a soft
cloth dipped in some neutral cleanserdiluted five or six times with water, andwrung out well, and then wipe again with a
dry cloth. Do not use furniture wax orcleansers.
Never use thinners, benzine, insecticide
sprays or other chemicals on or near thisunit, since these will corrode the surface.
Published by Pioneer Corporation.
Copyright 2009 Pioneer Corporation.
All rights reserved.
7/23/2019 XW NAS3 Operating Instructions
20/60
Cet appareil numrique de la Classe B est conforme la norme NMB-003 du Canada.
D8-10-1-3_A1_Fr
AVERTISSEMENTCet appareil nest pas tanche. Pour viter les risquesdincendie et de dcharge lectrique, ne placez prs delui un rcipient rempli deau, tel quun vase ou un potde fleurs, et ne lexposez pas des gouttes deau, desclaboussures, de la pluie ou de lhumidit.
D3-4-2-1-3_A1_Fr
AVERTISSEMENTPour viter les risques dincendie, ne placez aucuneflamme nue (telle quune bougie allume) surlappareil.
D3-4-2-1-7a_A1_Fr
AVERTISSEMENTAvant de brancher lappareil pour la premire, lisez
attentivement la section suivante.
La tension de lalimentation lectrique disponible
varie selon le pays ou la rgion. Assurez-vous que
la tension du secteur de la rgion o lappareil serautilis correspond la tension requise (par ex. 230
V ou 120 V), indique sur le panneau infrieur.D3-4-2-1-4*_A1_Fr
PRCAUTION DE VENTILATIONLors de linstallation de lappareil, veillez laisser unespace suffisant autour de ses parois de manire amliorer la dissipation de chaleur (au moins 20 cm surle dessus, 10 cm larrire et 10 cm de chaque ct).
AVERTISSEMENTLes fentes et ouvertures du coffret sont prvues pour laventilation, pour assurer un fonctionnement stable delappareil et pour viter sa surchauffe. Pour viter lesrisques dincendie, ne bouchez jamais les ouvertures etne les recouvrez pas dobjets, tels que journaux, nappesou rideaux, et nutilisez pas lappareil pos sur un tapispais ou un lit.
D3-4-2-1-7b*_A1_Fr
7/23/2019 XW NAS3 Operating Instructions
21/60
Ce point dexclamation, plac dans untriangle quilatral, a pour but dattirerlattention de lutilisateur sur la prsence,dans les documents qui accompagnentlappareil, dexplications importantes dupoint de vue de lexploitation ou delentretien.
Ce symbole de lclair, plac dans untriangle quilatral, a pour but dattirerlattention de lutilisateur sur la prsence, lintrieur du coffret de lappareil, detensions dangereuses non isoles dunegrandeur suffisante pour reprsenter unrisque dlectrocution pour les treshumains.
ATTENTION :POUR VITER TOUT RISQUEDLECTROCUTION, NE PAS ENLEVER LECOUVERCLE (NI LE PANNEAU ARRIRE).AUCUNE PICE RPARABLE PARLUTILISATEUR NE SE TROUVE LINTRIEUR. CONFIER TOUT ENTRETIEN UN PERSONNEL QUALIFI UNIQUEMENT.
ATTENTIONDANGER DELECTROCUTION
NE PAS OUVRIR
IMPORTANT
D3-4-2-1-1_A1_Fr
ATTENTIONLinterrupteur STANDBY/ONde cet appareil necoupe pas compltement celui-ci de sa prise secteur.Comme le cordon dalimentation fait office dedispositif de dconnexion du secteur, il devra tredbranch au niveau de la prise secteur pour quelappareil soit compltement hors tension. Parconsquent, veillez installer lappareil de tellemanire que son cordon dalimentation puisse trefacilement dbranch de la prise secteur en casdaccident. Pour viter tout risque dincendie, lecordon dalimentation sera dbranch au niveau de
la prise secteur si vous prvoyez une priodeprolonge de non utilisation (par exemple avant undpart en vacances).
D3-4-2-2-2a*_A1_Fr
Si la fiche dalimentation secteur de cet appareil neconvient pas la prise secteur utiliser, la fiche doittre remplace par une approprie. Ceremplacement et la fixation dune fiche secteur sur lecordon dalimentation de cet appareil doivent treeffectus par un personnel de service qualifi. En casde branchement sur une prise secteur, la fiche decoupure peut provoquer une srieuse dchargelectrique. Assurez-vous quelle est liminecorrectement aprs sa dpose.Lappareil doit tre dconnect en dbranchant safiche secteur au niveau de la prise murale si vous
prvoyez une priode prolonge de non utilisation(par exemple avant un dpart en vacances).D3-4-2-2-1a_A1_Fr
7/23/2019 XW NAS3 Operating Instructions
22/60
NOTE IMPORTANTE SUR LE CABLEDALIMENTATION
Tenir le cble dalimentation par la fiche. Ne pas
dbrancher la prise en tirant sur le cble et ne pastoucher le cble avec les mains mouilles. Cela risquede provoquer un court-circuit ou un choc lectrique. Nepas poser lappareil ou un meuble sur le cble. Ne paspincer le cble. Ne pas faire de noeud avec le cble oulattacher dautres cbles. Les cbles dalimentationdoivent tre poss de faon ne pas tre crass. Uncble abm peut provoquer un risque dincendie ou unchoc lectrique. Vrifier le cble dalimentation detemps en temps. Contacter le service aprs-ventePIONEER le plus proche ou le revendeur pour unremplacement.
S002*_A1_Fr
Lorsque vous utilisez ce produit, vrifiez lesinformations concernant la scurit sous lappareil.
D3-4-2-2-4_B1_Fr
Milieu de fonctionnementTemprature et humidit du milieu de fonctionnement :De +5 C +35 C (de +41 F +95 F) ; Humiditrelative infrieure 85 % (orifices de ventilation nonobstrus)Ninstallez pas lappareil dans un endroit mal ventil ouun lieu soumis une forte humidit ou en plein soleil(ou une forte lumire artificielle).
D3-4-2-1-7c*_A1_Fr
Ce produit est destin une utilisation domestique
gnrale. Toute panne due une utilisation autre qu'
des fins prives (comme une utilisation des fins
commerciales dans un restaurant, dans un autocar
ou sur un bateau) et qui ncessite une rparation
sera aux frais du client, mme pendant la priode de
garantie.K041_A1_Fr
Cessymbolesnesont
valablesquedanslespays
delUnionEuropenne.
K058c_A1_Fr
(Exemplesdemarquagepourlesbatteries)
Pb
7/23/2019 XW NAS3 Operating Instructions
23/60
5Fr
English
Franais
Espaol
Nous vous remercions davoir achet ce produit Pioneer.Veuillez lire attentivement ce mode demploi de manire pouvoir utiliser votre modlecorrectement. Aprs avoir lu ces explications, conservez-les en lieu sr pour ventuellement lesconsulter plus tard.
Table des matires01 Avant de commencerContenu de la bote . . . . . . . . . . . . . . . . . . . . . .6Avant dutiliser la tlcommande . . . . . . . . . . .6
Remplacement de la pile . . . . . . . . . . . . . . . .6Utilisation de la tlcommande . . . . . . . . . . .7
Installation de lappareil . . . . . . . . . . . . . . . . . .7
Branchement . . . . . . . . . . . . . . . . . . . . . . . . . .702 Commandes et afficheur
Tlcommande. . . . . . . . . . . . . . . . . . . . . . . . .8Panneau avant/suprieur . . . . . . . . . . . . . . . . .8
03 Lecture de iPodVrifiez quels modles diPod sont pris encharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Connexion de votre iPod. . . . . . . . . . . . . . . . . .9
Connexion de votre tlviseur . . . . . . . . . . . .10Lecture de votre iPod. . . . . . . . . . . . . . . . . . . .11
Utilisation des commandes de tonalit . . . . .11
04 ADAPTATEUR Bluetooth pourprofiter de la musique sans filLecture de musique sans fil. . . . . . . . . . . . . . .13
Fonctionnement par tlcommande . . . . . . .13Raccordement de lADAPTATEUR Bluetoothoptionnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Rglage du code PIN. . . . . . . . . . . . . . . . . . . .14Pairage de lADAPTATEUR Bluetoothetdun priphrique technologie sans filBluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14coute de contenus musicaux dunpriphrique technologie sans fil Bluetoothavec votre systme . . . . . . . . . . . . . . . . . . . . .15
05 Autres raccordementsConnexion dappareils auxiliaires . . . . . . . . . .16
06 Informations supplmentairesGuide de dpannage . . . . . . . . . . . . . . . . . . . .17Rinitialisation du systme. . . . . . . . . . . . . . .18
propos de liPod/iPhone . . . . . . . . . . . . . . . .18Spcifications. . . . . . . . . . . . . . . . . . . . . . . . .19Nettoyage de lappareil. . . . . . . . . . . . . . . . . .19
7/23/2019 XW NAS3 Operating Instructions
24/60
Avant de commencer01
6Fr
Chapitre 1 :
Avant de commencerContenu de la boteVeuillez confirmer que les accessoiressuivants sont prsents dans la bote quandvous louvrez.
Tlcommande
Support de tlcommande
Pile lithium (CR2025)
Cordon dalimentation
Chiffon de nettoyage
Mode demploi (ce document)
Avant dutiliser latlcommande
La tlcommande se trouve dj dans lesupport de tlcommande au moment delexpdition.
La pile fournie avec cet appareil est conservedans le botier pile.
Veuillez retirez le film protecteur dubotier pile.Si vous remarquez une diminution de la portede fonctionnement, remplacez la pile (voir ci-dessous).
Remplacement de la pilePour remplacer la pile, utilisez une pile lithiumCR2025 en vente dans le commerce.
1 Poussez le loquet douverture vers lagauche pour ouvrir le botier pile.
2 Retirez le botier pile.
3 Enlevez la pile du botier.
4 Placez une pile neuve dans le botier.
Assurez-vous que le ctde la pile esttourn vers le haut quand vous la placez lendroit prvu.
Attention
Lorsque vous utilisez des piles lithium, veuilleztenir compte des prcautions suivantes :
Il y a un risque dexplosion si la pile nestpas correctement remplace. Assurez-
vous de les remplacer uniquement par lemme type de pile ou un type quivalentrecommand par le fabricant.
Jetez les piles uses immdiatement aprsles avoir remplaces. Gardez-les hors deporte des enfants.
En cas dingestion, veuillez contacterimmdiatement un mdecin.
Les piles lithium prsentent des risques defeu ou de brlures chimiques si elles sont
mal employes. Ne les dmontez pas, neles chauffez pas plus de 100 C ni ne lesincinrez.
Enlevez la pile de lappareil si vous prvoyez
de ne pas lutiliser pendant un mois ou plus.
1
1
3
2
7/23/2019 XW NAS3 Operating Instructions
25/60
Avant de commencer 01
7Fr
English
Franais
Espaol
Lorsque vous jetez des piles / batteriesuses, veuillez vous conformer aux normesgouvernementales ou environnementalesen vigueur dans votre pays ou rgion.
AVERTISSEMENTNutilisez ni ne conservez les piles sous lalumire directe du soleil ou dans unendroit excessivement chaud, comme unevoiture ou proximit dun appareil dechauffage. Les piles risqueraient de fuir, desurchauffer, dexploser ou de senflammer.Leur dure de vie ou leur performance
pourrait galement tre rduite. Matriau perchlorate Un maniement spcialpeut sappliquer. Consultez le site:www.dtsc.ca.gov/hazardouswaste/perchlorate.(Applicable en Californie, Etats-Unis)
Utilisation de la tlcommandeLa tlcommande a une porte denviron7 mtres avec un angle de 30 par rapport aucapteur de tlcommande.
Gardez lesprit ce qui suit lorsque vousutilisez la tlcommande :
Assurez-vous de labsence dobstacles entre
la tlcommande et le capteur de lappareil.
La tlcommande risque de ne pasfonctionner correctement si la lumire dusoleil ou une lampe fluorescente puissanteclaire le capteur de lappareil.
Les tlcommandes de diffrents appareilspeuvent interfrer entre elles. Evitezdutiliser des tlcommandes
commandant dautres quipements situs proximit de cet appareil.
Remplacez les piles lorsque vous constatezune diminution de la porte defonctionnement de la tlcommande.
Installation de lappareil Lors de linstallation de lappareil, assurez-vous que ce dernier est pos sur unesurface plane et stable.
Ninstallez pas lappareil dans les endroitssuivants : sur un tlviseur couleur (les images lcran pourraient tre dformes) proximit dune platine cassettes (ou dunappareil qui produit un champ magntique).
Le son pourrait sen trouver affect. la lumire directe du soleil lhumidit des tempratures extrmes en prsence de vibrations ou autresmouvements la poussire la fume ou aux manations graisseuses(cuisine par ex.)
BranchementAprs avoir termin de faire tous lesbranchements, branchez lappareil sur uneprise secteur murale.
1 Branchez le cordon dalimentation fournisur la prise AC INsitue larrire de cetappareil.
2 Branchez lautre extrmit sur une prisesecteur murale.
Important
Avant deffectuer ou de modifier lesraccordements, mettez lappareil horstension et dbranchez le cordondalimentation de la prise secteur.
3030
7 m
AUDIO IN
AC IN
7/23/2019 XW NAS3 Operating Instructions
26/60
Commandes et afficheur02
8Fr
Chapitre 2 :
Commandes et afficheurTlcommande
1 STANDBY/ONCette touche permet de mettre lappareil enmode de veille et sous tension.
2 INPUTUtilisez ces touches pour slectionner unesource dentre. Appuyez rptitivement sur
cette touche pour choisir liPod, lADAPTATEUR
Bluetooth1et lentre extrieure.
3 VOLUME +/Permet de rgler le volume dcoute.
4 Touches de commande de la lectureUtilisez ces touches pour commander un iPod ou
un priphrique technologie sans fil Bluetooth
avec cette tlcommande (page 11, 15).
Panneau avant/suprieur1 Enceintes
2 Prise de connexion iPod
3 STANDBY/ONCette touche permet de mettre lappareil enmode de veille et sous tension.
4 Indicateur dalimentation
5 INPUT SELECTOR
Utilisez ces touches pour slectionner unesource dentre. Appuyez rptitivement surcette touche pour choisir liPod, lADAPTATEUR
Bluetooth1et lentre extrieure.
6 VOLUME +/Permet de rgler le volume dcoute.
7 Indicateur de lADAPTATEUR Bluetooth
8 Capteur de tlcommande
9 Indicateur diPod
STANDBY/ON
INPUT
VOLUME
1 3
42
Remarque1 Quand lADAPTATEUR Bluetoothnest pas branch sur le port ADAPTER PORT, le mode dentre de lADAPTATEUR Bluetooth
ne peut pas tre slectionn mme si vous appuyez sur INPUT.
1 2
9
8
7
STANDBY/ON INPUT SELECTOR
VOLUME
3 4 5 6
7/23/2019 XW NAS3 Operating Instructions
27/60
Lecture de iPod 03
9Fr
English
Franais
Espaol
Chapitre 3 :
Lecture de iPodDe plus, en connectant votre iPod ce systmedenceintes, vous pouvez profiter dun sonnumrique de grande qualit directement partir de votre iPod. Ces enceintes peuventaussi tre raccordes un tlviseur, vouspermettant de voir les images de votre iPod.
La lecture et le rglage du niveau de volumepour la musique et les images de liPodpeuvent tre raliss partir de cet appareil oude liPod lui-mme.
Vrifiez quels modles diPodsont pris en chargeCe systme est compatible avec la lectureaudio et vido de liPod nano 3e gnration etsuprieure, iPod classic, iPod touch et iPhone.
Il prend aussi en charge la lecture audio deliPod nano deuxime gnration.1
Utilisez toujours la version la plus rcentedisponible du logiciel diPod. La compatibilitpeut dpendre en fonction de la version dulogiciel utilis. Vous pouvez vrifier la versionde votre logiciel sur votre iPod de la faonsuivante:
1 Slectionnez Settings sur le menuprincipal.
2 Slectionnez About.La version du logiciel est affiche.
Consultez le site Web dApple au sujet desversions les plus rcentes du logiciel et desinstructions sur la mise jour de votreversion.
Note
Lors de lutilisation dun iPod non pris en
charge par cet appareil, utilisez un cbleen vente dans le commerce pourconnecter liPod au connecteur AUDIO INde cet appareil.
Connexion de votre iPod
Attention
Pour viter tout dommage lors de laconnexion dun iPod, utilisez toujoursladaptateur de Dock fourni avec votre iPodou un adaptateur de Dock en vente dans lecommerce et conu spcialement pourvotre modle de iPod.
Remarque
1 Certaines fonctions peuvent ne pas tre accessibles en fonction du modle et de la version du logiciel. iPod a une licence pour la reproduction de contenus non protgs ou de contenus que lutilisateur est autoris reproduire lgalement. Les fonctions telles que lgaliseur ne peuvent pas tre commandes en utilisant ce systme, et nousrecommandons de mettre lgaliseur hors service avant la connexion.
Pioneer ne peut tre en aucun cas tenu responsable pour toute perte directe ou indirecte lie un problme ou uneperte des donnes enregistres la suite dune dfaillance de liPod. Quand vous raccordez un iPod, utilisez le menu Speaker et loption Backlight pour rgler la fonction dertroclairage de liPod. Cela ne concerne pas liPod touch.
7/23/2019 XW NAS3 Operating Instructions
28/60
Lecture de iPod03
10Fr
1 Attachez ladaptateur de Dock la prisede connexion situe sur le panneau suprieurde cet appareil.
Aucun adaptateur de Dock nest fourniavec cet appareil.
Lors de la fixation de ladaptateur de Dock,assurez-vous dorienter correctement les
directions avant-arrire de ladaptateur deDock. Pour attacher ladaptateur de Dock,placez dabord les parties saillantes de la faceavant de ladaptateur dans les creuxcorrespondants de la prise de connexiondiPod et poussez pour insrer. Lors de lafixation de ladaptateur, faites attention de nepas abimer les connecteurs.
2 Raccordez votre iPod.
Connexion de votre tlviseur
Pour regarder les images de liPod sur untlviseur, faites une connexion en utilisant uncble vido composite ou un cble vido encomposantes.
Lors de lutilisation dun cble vido encomposantes pour les connexions, il estncessaire de rgler la sortie vido delappareil. Reportez-vous Rglage de lasortie vido la page 11.
Quand un iPod est raccord cet appareil,
le rglage de sortie du tlviseur est rglautomatiquement sur ON (en service).Pendant quil est raccord, liPod peut treutilis pour modifier le rglage de sortie dutlviseur.1
Attention
Avant deffectuer ou de modifier lesraccordements, mettez lappareil horstension et dbranchez le cordon
dalimentation de la prise secteur. Lesconnexions doivent se faire en tout dernier.
MENU
iPod
Adaptateur deDock
Remarque1 Cette fonction est limite aux modles diPod possdants des rglages de sortie de tlviseur.
Quand liPod est dconnect de cet appareil, le rglage de sortie de tlviseur de liPod retourne son rglage dorigine.
COMPONENT VIDEO
MONITOR OUT VIDEO 1VIDEO 2
ADAPTER PORT
Y PB PR AUDIO IN
Tlviseur
Cble vido en
composantes(en vente dans lecommerce)
Cble vido
composite(en vente dansle commerce)
7/23/2019 XW NAS3 Operating Instructions
29/60
Lecture de iPod 03
11Fr
English
Franais
Espaol
Rglage de la sortie vidoRglez la sortie vido sur cet appareil enfonction de la mthode utilise pour connecterle tlviseur.1
Rglage par dfaut : Composite
1 Mettez lappareil en veille.
2 Appuyez sur INPUT sur la tlcommande
et maintenez enfonc pendant troissecondes.Lindicateur diPod clignote deux fois et lasortie vido est change sur Composantes.Quand vous rptez ltape 2, lindicateur iPodclignote une fois et la sortie vido est changesur Composite.
Lecture de votre iPod
Attention
Quand votre iPod est connect cetappareil et que vous souhaitez commanderliPod en le touchant directement, assurez-vous de tenir solidement liPod avec lautremain pour viter un mauvaisfonctionnement caus par un mauvaiscontact.
Quand un iPod est raccord cet appareil,lindicateur diPod clignote pendant quelappareil vrifie la connexion avec liPod etobtient les donnes de liPod. Quand vousappuyez sur INPUTpour changer lentre surliPod, la connexion termine et lindicateurdiPod reste allum.2
La lecture et le rglage du niveau de volumepour la musique et les images de liPodpeuvent tre raliss partir de cet appareil oude liPod lui-mme.
Lors de lutilisation de liPod pour rgler levolume sonore, le rglage appliquuniquement au son produit par lesenceintes de cet appareil.3Si liPod estdconnect de cet appareil, le volumesonore de liPod revient son rglagedorigine.
Les oprations suivantes sont possibles pourliPod en utilisant la tlcommande.
Utilisation des commandes de
tonalitRglez la tonalit du son. Le rglage est ralis partir de lcran de liPod.3Les rglagesraliss ici sont rflchis dans les rglages desBASS/TREBLE (graves/aigus) de cet appareil.
Remarque
1 Arrtez la lecture vido du iPod avant de changer le rglage de sortie vido. Le mode de rglage ne peut pas tre changpendant la lecture ou une pause. Pendant la procdure de rglage de la sortie vido, si vous nappuyez sur aucune touche pendant 3 minutes, le rglage estannul et lappareil retourne en mode veille.
2 Si un iPod est connect quand cet appareil est en mode veille, il se met sous tension et lentre de liPod est slectionneautomatiquement.
INPUT
3 Ces rglages sont appliqus toutes les entres de lappareil.
Touches Leur rle
/ Dmarre la lecture normale et active/dsactive la mise en pause de lalecture.
Appuyez sur cette touche pour sauter
au dbut du fichier en cours, puis aux
fichiers prcdents. Maintenez cette
touche enfonce pour lancer le
dfilement rapide arrire.
Appuyez sur cette touche pour sauter
au fichier suivant. Maintenez cette
touche enfonce pour lancer le
dfilement rapide avant.
VOLUME
+/Permet de rgler le volumedcoute.
7/23/2019 XW NAS3 Operating Instructions
30/60
Lecture de iPod03
12Fr
iPod nano ou iPod classic:
1 Slectionnez Speaker sur le menuprincipal.
2 Slectionnez Tone control.
3 Slectionnez un rglage.
iPod touch ou iPhone:1
1 Slectionnez Settings sur le menuprincipal.
2 Slectionnez Speaker.
3 Slectionnez Tone control.
4 Slectionnez un rglage.
Slectionnez un des paramtres suivants :
Flat Rtablissement du son son tatnaturel.
Bass ON Accentuation des sons graves. Treble ON Accentuation des sons aigus. Bass/Treble ON Accentuation des sons
graves et aigus.
Important
Si lindicateur dalimentation et lindicateurdiPod clignotent simultanment, cest quil y aun problme de connexion. Effectuez lesvrifications suivantes et prenez les mesuresncessaires:
Vrifiez si liPod est pris en charge par cet
appareil. Reconnectez liPod et lappareil. Si cela ne
fonctionne pas, essayez de refaire lesrglages de liPod.
Mettez jour le logiciel de liPod ladernire version.
Si liPod ne peut pas tre utilis, vrifiez lespoints suivants:
LiPod est-il raccord correctement?Reconnectez liPod lappareil.
LiPod est-il bloqu? Essayez de rinitialiserliPod et de le reconnecter lappareil.
Note
LiPod se charge chaque fois quil estconnect cet appareil. (Cest aussivalable quand lappareil se trouve en modeveille.)
Chaque fois quun iPod est connect cetappareil, mettre lappareil sous tension ouchanger lentre sur iPod permet dedmarrer la lecture de liPodautomatiquement.
Quand lentre est change de liPod surune autre fonction, la lecture de liPodsarrte automatiquement.
Si lappareil est mis en veille quand un iPodest connect, liPod est mis hors tensionautomatiquement.
Remarque
1 Ce rglage peut ne pas tre pris en charge en fonction de la version du logiciel de liPod touch ou iPhone software version.
7/23/2019 XW NAS3 Operating Instructions
31/60
ADAPTATEUR Bluetooth pour profiter de la musique sans fil 04
13Fr
English
Franais
Espaol
Chapitre 4 :
ADAPTATEUR Bluetoothpourprofiter de la musique sans fil
Lecture de musique sans filLorsque lADAPTATEUR Bluetooth(modlePioneer n AS-BT100) est raccord cetappareil, un produit quip de la technologiesans fil Bluetooth(tlphone portable, lecteurde musique numrique, etc.) peut tre utilispour couter de la musique sans fil.1De plus,en utilisant un metteur disponible dans lecommerce prenant en charge la technologie
sans fil Bluetooth, vous pouvez couter de lamusique sur un priphrique non quip de latechnologie sans fil Bluetooth. Le modleAS-BT100 prend en charge la protection de
contenus SCMS-T, ainsi il est possible deprofiter de la musique sur des priphriquesquips de la technologie sans fil Bluetoothdetype SCMS-T.
Fonctionnement par tlcommandeLa tlcommande fournie avec cet appareilvous permet de lire et darrter le support etdeffectuer dautres oprations.2
Fonctionnement par tlcommande
Cet appareil
ADAPTATEURBluetooth
Priphrique non quip de latechnologie sans fil Bluetooth :Lecteur de musique numrique
+metteur audio Bluetooth (envente dans le commerce)
Priphrique optimis pour latechnologie sans fil Bluetooth :Lecteur de musique numrique
Priphrique optimispour la technologie sans filBluetooth :
Tlphone portable
Remarque1 Il peut savrer ncessaire que le priphrique optimis pour la technologie sans fil Bluetoothprenne en charge les profils
A2DP. Pioneer ne garantit pas une connexion et un fonctionnement correct de cet appareil avec tous les priphriques optimiss pourla technologie sans fil Bluetooth.
2 Il peut savrer ncessaire que le priphrique optimis pour la technologie sans fil Bluetoothprenne en charge les profilsAVRCP. Le fonctionnement de la tlcommande ne peut tre garanti pour tous les priphriques optimiss pour la technologie sansfil Bluetooth.
7/23/2019 XW NAS3 Operating Instructions
32/60
ADAPTATEUR Bluetooth pour profiter de la musique sans fil04
14Fr
Raccordement de lADAPTATEURBluetoothoptionnel Avant deffectuer ou de modifier les
raccordements, mettez lappareil horstension et dbranchez le cordondalimentation de la prise secteur.
1 Mettez lappareil en veille et raccordezlADAPTATEUR Bluetoothau port ADAPTERPORTsitu sur le panneau arrire.
2 Appuyez sur STANDBY/ON.
3 Appuyez sur INPUTpour choisir le modedentre de lADAPTATEUR Bluetooth.1
Lindicateur de lADAPTATEUR Bluetoothclignote.
Rglage du code PINRglez le code PIN de cet appareil sur la mmevaleur que celui du priphrique technologie
sans fil Bluetoothutilis. Les valeurs prises encharge pour le code PIN sont du type 0000,1234 ou 8888.
Rglage par dfaut : 0000
1 Mettez lappareil en veille.
2 Appuyez suret maintenez enfoncpendant trois secondes.Lindicateur de lADAPTATEUR Bluetoothclignote et le code PIN est chang. Le nombrede clignotements correspond au nouveau codePIN rgl, comme indiqu ci-dessous:
1 clignotement: 0000
2 clignotements: 1234
3 clignotements: 8888
Rptez ltape 2 jusqu ce que le code PINsoit rgl sur la valeur souhaite.
Pairage de lADAPTATEURBluetoothet dun priphrique technologie sans fil BluetoothLappairage doit tre effectu avec decommencer la lecture de contenu technologie sans fil Bluetooth laide delADAPTATEUR Bluetooth. Assurez-vousdeffectuer lappairage la premire fois quevous utilisez le systme ou chaque fois queles donnes dappairage sont effaces.Lappairage est ltape ncessaire pourenregistrer le priphrique technologie sansfil Bluetoothafin de permettre lescommunications Bluetooth.2Pour plus dedtails, reportez-vous aussi au mode demploide votre priphrique technologie sans fil
Bluetooth.
Remarque
1 Quand lADAPTATEUR Bluetoothnest pas branch sur le port ADAPTER PORT, le mode dentre de lADAPTATEUR Bluetoothne peut pas tre slectionn mme si vous appuyez sur INPUT.
COMPONENT VIDEO
MONITOR OUT VIDEO 1VIDEO 2
ADAPTER PORT
Y PB PR
ADAPTATEURBluetooth
INPUT
2 Lappairage est requis la premire fois que vous utilisez le priphrique technologie sans fil Bluetoothet lADAPTATEURBluetooth. Pour permettre la communication Bluetooth, lappairage doit tre effectu avec votre systme ainsi quavec le priphrique technologie sans fil Bluetooth.
INPUT
7/23/2019 XW NAS3 Operating Instructions
33/60
ADAPTATEUR Bluetooth pour profiter de la musique sans fil 04
15Fr
English
Franais
Espaol
1 Quand lindicateur de lADAPTATEURBluetoothclignote, appuyez sur.
Lindicateur de lADAPTATEUR Bluetoothclignote rapidement et lappareil entre enmode de veille dapparairage.
2 Allumez le priphrique technologiesans fil Bluetoothavec lequel vous souhaitezeffectuer lappairage, placez-le prs dusystme et rglez-le sur le mode dappairage.Lappairage commence.
3 Vrifiez que lADAPTATEUR Bluetoothest
dtect par le priphrique technologiesans fil Bluetooth.Lindicateur de lADAPTATEUR Bluetoothsallume quand un priphrique technologiesans fil Bluetoothest connect.
Lindicateur de lADAPTATEUR Bluetoothclignote doucement quand aucunpriphrique technologie sans fil Bluetoothnest connect. Dans ce cas, ralisez uneconnexion partir du ct du priphrique
technologie sans fil Bluetooth.
coute de contenus musicauxdun priphrique technologiesans fil Bluetoothavec votresystme
1 Appuyez sur INPUTpour choisir le mode
dentre de lADAPTATEURBluetooth
.Lindicateur de lADAPTATEUR Bluetoothclignote.
2 Raccordez le priphrique technologiesans fil Bluetooth lADAPTATEURBluetooth.
3 Lancez la lecture des contenus musicauxmmoriss sur le priphrique technologiesans fil Bluetooth.Les oprations suivantes sont maintenantaccessibles pour les priphriques technologie sans fil Bluetooth, en utilisant latlcommande.1
Remarque1 Le priphrique technologie sans fil Bluetoothdoit tre compatible avec le profil AVRCP.
Selon le priphrique technologie sans fil Bluetoothque vous utilisez, le fonctionnement peut tre diffrent par rapport ce qui est indiqu dans le tableau.
Touches Leur rle
/ Dmarre la lecture normale et active/dsactive la mise en pause de lalecture.
Appuyez sur cette touche pour sauter
au dbut du fichier en cours, puis aux
fichiers prcdents. Maintenez cette
touche enfonce pour lancer le
dfilement rapide arrire.
Appuyez sur cette touche pour sauterau fichier suivant. Maintenez cette
touche enfonce pour lancer le
dfilement rapide avant.
VOLUME
+/Permet de rgler le volumedcoute.
7/23/2019 XW NAS3 Operating Instructions
34/60
Autres raccordements05
16Fr
Chapitre 5 :
Autres raccordements Avant deffectuer ou de modifier les
raccordements, mettez lappareil horstension et dbranchez le cordondalimentation de la prise secteur.
Connexion dappareils
auxiliairesConnectez la mini fiche AUDIO IN votreappareil de lecture auxiliaire.
Cette mthode peut tre utilise pour liresur cet appareil la musique diPod qui nepeuvent pas tre utiliss avec le Dock iPod.
Appuyez sur INPUTpour choisir le modedentre extrieure.Lindicateur diPod et lindicateur delADAPTATEUR Bluetoothsteignent.
COMPONENT VIDEO
MONITOR OUT VIDEO 1VIDEO 2
Y PB PR AUDIO IN
AC IN
Lecteur audio
numrique, etc.
7/23/2019 XW NAS3 Operating Instructions
35/60
Informations supplmentaires 06
17Fr
English
Franais
Espaol
Chapitre 6 :
Informations supplmentaires
Guide de dpannageDes oprations incorrectes sont souvent interprtes comme des problmes et des mauvaisfonctionnements. Si vous pensez quil y a un problme avec ce composant, vrifiez les points ci-dessous. Parfois le problme peut se trouver dans un autre composant. Examinez les autrescomposants et les appareils lectriques en usage. Si le problme ne peut pas se rsoudre malgr
les indications ci-dessous, consultez votre service aprs-vente Pioneer le plus proche pour le fairerparer.
Si lappareil ne fonctionne pas normalement en raison deffets externes comme llectricit
statique, dbranchez la fiche dalimentation de la prise de courant et insrez-la de nouveau
pour rtablir les conditions normales de fonctionnement.
Problmes Solutions
Impossible de mettre soustension.
Dbranchez la fiche dalimentation de la prise de courant et insrez-lade nouveau. Si le rcepteur darrte automatiquement, apportez-le au service aprs-vente Pioneer ou votre revendeur le plus proche pour le faire rviser.
Lappareil se metautomatiquement en modeveille sans intervention delutilisateur.
Quand lentre est rgle sur liPod et si aucun iPod nest connectpendant une heure ou plus, lappareil se met automatiquement horstension.
Aucun son nest fourni quandune fonction est slectionne.
Vrifiez que le composant est raccord correctement (voir Connexiondappareils auxiliaires la page 16).
Impossible de faire fonctionnerla tlcommande.
Remplacez les piles (voir page 6). Utilisez moins de 7 m, 30 du capteur de tlcommande du panneauavant (voir page 7).
Eliminez tout obstacle ou faites-la fonctionner dune autre position. vitez dexposer le capteur de tlcommande du panneau avant lalumire directe.
7/23/2019 XW NAS3 Operating Instructions
36/60
Informations supplmentaires06
18Fr
Rinitialisation du systmeCette procdure permet de restaurer laconfiguration dusine du systme.
Avant de rinitialiser lappareil,dbranchez dabord tous les appareilsconnects cet appareil.
1 Mettez lappareil sous tension.
2 Maintenez enfonc VOLUME sur lepanneau suprieur et ensuite maintenezenfoncSTANDBY/ONpendant troissecondes.
Lappareil est mis en mode veille.
la prochaine mise sous tension, tous lesrglages du systme doivent tre rinitialiss.
propos de liPod/iPhone
Les accessoires lectroniques portant la
mention Made for iPod et Made for iPhone ont t conus pour fonctionnerrespectivement avec un iPod ou un iPhone etsont certifis conformes aux exigencesdApple par le fabricant. Apple nest pasresponsable pour le fonctionnement de cetappareil ou de sa compatibilit avec lesnormes rglementaires et de scurit.
iPod et iPhone sont des marques commercialesdApple Inc., enregistres aux tats-Unis et dans
dautres pays.
Le priphrique technologiesans fil Bluetoothne peut pastre raccord ou utilis. Le sonen provenance du priphrique technologie sans fil Bluetoothnest pas mis ou le son estinterrompu.
Vrifiez quaucun objet mettant des ondes lectromagntiques dans labande 2,4 GHz (four micro-ondes, priphrique LAN sans fil ou appareil technologie sans fil Bluetooth) nest proximit de lappareil. Si un telobjet se trouve proximit de lappareil, loignez-en lappareil. Vouspouvez aussi arrter dutiliser lobjet mettant les ondeslectromagntiques. Vrifiez que le priphrique technologie sans fil Bluetoothnest pastrop loign de lappareil et quil ny a pas dobstructions entre lepriphrique technologie sans fil Bluetoothet lappareil. Placez lepriphrique technologie sans fil Bluetoothet lappareil de faon ceque la distance entre eux soit infrieure 10 m et quil ny ait pasdobstructions entre eux.
Vrifiez que lADAPTATEUR Bluetoothet le portADAPTER PORT
delappareil sont correctement raccords. Il se peut que le priphrique technologie sans fil Bluetoothne soitpas tre rgl sur le mode de communication prenant en charge latechnologie sans fil Bluetooth. Vrifiez le rglage du priphrique technologie sans fil Bluetooth. Vrifiez que lappairage est correct. Le rglage dappairage a tsupprim de cet appareil ou du priphrique technologie sans filBluetooth. Rglez de nouveau lappairage. Vrifiez que le profil est correct. Utilisez un priphrique technologiesans fil Bluetoothprenant en charge le profil A2DP et le profil AVRCP.
Problmes Solutions
7/23/2019 XW NAS3 Operating Instructions
37/60
Informations supplmentaires 06
19Fr
English
Franais
Espaol
Spcifications Section amplificateurPuissance de sortie RMS:
Avant gauche/droit . . . . . . . . . . . 15 W + 15 W(1 kHz, 10 %, T.H.D., 8)
Caisson de graves. . . . . . . . . . . 30 W(100 Hz, 10 %, T.H.D., 4 )
Section des enceintesBotier . . Bass-reflex (avec blindage magntique)Systme . . . . . . . . . . . . . . . . . . . systme 2 voiesEnceintes :
Caisson de graves . . . . . . . . . . . cne de 10 cmGamme tendue . . . . . . . . . . . . cne de 5,2 cm
Gamme de frquences . . . . . . . . . 50 Hz 20 kHz
DiversAlimentation. . . . . . . . . . . . . . . . .120 V c.a., 60 HzConsommation . . . . . . . . . . . . . . . . . . . . . . . 30 W
En mode veille . . . . . . . . . . . . . . . . . . . . . . 0,5 WDimensions. . . . . . . . 420 mm (L) x 148 mm (H) x 210 mm (P)
Poids (sans emballage). . . . . . . . . . . . . . . . .4,9 kg
AccessoiresTlcommande . . . . . . . . . . . . . . . . . . . . . . . . . . .1Support de tlcommande . . . . . . . . . . . . . . . . . .1Pile lithium (CR2025). . . . . . . . . . . . . . . . . . . . . . .1Cble dalimentation . . . . . . . . . . . . . . . . . . . . . . .1Chiffon de nettoyage . . . . . . . . . . . . . . . . . . . . . . .1Mode demploi (ce document)
Remarque
Les spcifications et la conception sontsujettes de possibles modifications sanspravis, suite des amliorations.
Nettoyage de lappareil Utilisez un chiffon sec pour essuyer lapoussire et la salet.
Lorsque le surface est sale, essuyez avecun chiffon doux tremp dans un nettoyantneutre dilu dans une dose cinq ou six foissuprieure deau, et bien essor. Essuyezencore avec un chiffon sec. Nutilisez pasde cire ou nettoyant pour meubles.
Nutilisez jamais de diluants, benzine,
insecticides en bombe ou autres produitschimiques sur ou prs de cet appareil aurisque dentraner une corrosion.
Publication de Pioneer Corporation. 2009 Pioneer Corporation.Tous droits de reproduction et de traduction rservs.
7/23/2019 XW NAS3 Operating Instructions
38/60
ADVERTENCIAEste aparato no es impermeable. Para evitar el riesgode incendio y de descargas elctricas, no ponga ningnrecipiente lleno de lquido (como pueda ser un vaso oun florero) cerca del aparato ni lo exponga a goteo,salpicaduras, lluvia o humedad.
D3-4-2-1-3_A1_Es
ADVERTENCIAPara evitar el peligro de incendio, no ponga nada confuego encendido (como pueda ser una vela) encima delaparato.
D3-4-2-1-7a_A1_Es
ADVERTENCIAAntes de enchufar el aparato a la corriente, lea la seccin
siguiente con mucha atencin.
La tensin de la red elctrica es distinta segn el
pas o regin. Asegrese de que la tensin de la
alimentacin de la localidad donde se proponga
utilizar este aparato corresponda a la tensin
necesaria (es decir, 230 V 120 V) indicada en el
panel inferior.D3-4-2-1-4*_A1_Es
PRECAUCIN PARA LA VENTILACINCuando instale este aparato, asegrese de dejarespacio en torno al mismo para la ventilacin con el finde mejorar la disipacin de calor (por lo menos 20 cmencima, 10 cm detrs, y 10 cm en cada lado).
ADVERTENCIALas ranuras y aberturas de la caja del aparato sirvenpara su ventilacin para poder asegurar unfuncionamiento fiable del aparato y para protegerlocontra sobrecalentamiento. Para evitar el peligro deincendio, las aberturas nunca debern taparse nicubrirse con nada (como por ejemplo, peridicos,manteles, cortinas) ni ponerse en funcionamiento elaparato sobre una alfombra gruesas o una cama.
D3-4-2-1-7b*_A1_Es
7/23/2019 XW NAS3 Operating Instructions
39/60
El punto exclamativo dentro un tringuloequiltero convenido para avisar el usuriode la presencia de importantesinstrucciones sobre el funcionamiento y lamanutencin en la libreta que acompaa elaparato.
La luz intermitente con el smbolo de puntade flecha dentro un tringulo equiltero.Est convenido para avisar el usuario de lapresencia de voltaje peligrosa no aisladadentro el producto que podra constituir unpeligro de choque elctrico para laspersonas.
ATENCIN:PARA PREVENIR EL PELIGRO DE CHOQUEELCTRICO NO REMOVER LA TAPA NI LASPARTES DENTRO NO UTILIZADAS,LLAMAR UNA PERSONA CUALIFICADA.
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANTE
D3-4-2-1-1_A1_Es
PRECAUCINEl interruptor de la alimentacin STANDBY/ONdeeste aparato no corta por completo toda la
alimentacin de la toma de corriente de CA. Puesto
que el cable de alimentacin hace las funciones de
dispositivo de desconexin de la corriente para el
aparato, para desconectar toda la alimentacin del
aparato deber desenchufar el cable de la toma de
corriente de CA. Por lo tanto, asegrese de instalar
el aparato de modo que el cable de alimentacin
pueda desenchufarse con facilidad de la toma de
corriente de CA en caso de un accidente. Para evitar
correr el peligro de incendio, el cable de
alimentacin tambin deber desenchufarse de latoma de corriente de CA cuando no se tenga la
intencin de utilizarlo durante mucho tiempo seguido
(por ejemplo, antes de irse de vacaciones).D3-4-2-2-2a*_A1_Es
SilaclavijadelcabledealimentacindeCAdeesteaparatonoseadaptaalatomadecorrientedeCA
queusteddeseautilizar,debercambiarlaclavijapor
otraqueseadapteapropiadamente.Elreemplazoy
montajedeunaclavijadelcabledealimentacinde
CAslodeberrealizarlospersonaldeservicio
tcnicocualificado.Siseenchufalaclavijacortadaa
unatomadecorrientedeCA,puedecausarfuertes
descargaselctricas.Asegresedequesetiradela
formaapropiadadespusdehaberlaextrado.
Elaparatodeberdesconectarsedesenchufandola
clavijadelaalimentacindelatomadecorriente
cuandonosepropongautilizarlodurantemucho
tiempo(porejemplo,antesdeirsedevacaciones).D3-4-2-2-1a_A1_Es
7/23/2019 XW NAS3 Operating Instructions
40/60
PRECAUCIONES CONCERNIENTES A LAMANIPULACIN DEL CABLE DEALIMENTACIN
Tome el cable de alimentacin por la clavija. Noextraiga la clavija tirando del cable. Nunca toque el
cable de alimentacin cuando sus manos estn
mojadas, ya que esto podra causar cortocircuitos o
descargas elctricas. No coloque la unidad, algn
mueble, etc., sobre el cable de alimentacin.
Asegrese de no hacer nudos en el cable ni de unirlo a
otros cables. Los cables de alimentacin debern ser
dispuestos de tal forma que la probabilidad de que
sean pisados sea mnima. Una cable de alimentacin
daado podr causar incendios o descargas elctricas.
Revise el cable de alimentacin est daado, solicite el
reemplazo del mismo al centro de servicio autorizado
PIONEER ms cercano, o a su distribuidor.S002*_A1_Es
Cuando utilice este producto, confirme la
informacin de seguridad mostrada en la parte
inferior de la unidad.D3-4-2-2-4_B1_Es
Entorno de funcionamientoTemperatura y humedad del entorno de funcionamiento
+5 C a +35 C; menos del 85 % de humedad relativa
(rejillas de refrigeracin no obstruidas)
No instale este aparato en un lugar mal ventilado, ni en
lugares expuestos a alta humedad o a la luz directa del
sol (o de otra luz artificial potente).D3-4-2-1-7c*_A1_Es
Esteproductoesparatareasdomsticasgenerales.
Cualquieraaveradebidaaotrautilizacinquetareas
domsticas(talescomoelusoalargoplazopara
motivosdenegociosenunrestauranteoelusoenun
cocheounbarco)yquenecesitaunareparacin
harque
cobrarla
incluso
durante
el
perodo
de
garanta.K041_A1_Es
Estossmbolossloson
vlidosenlaUninEuropea.
K058c_A1_Es
(Ejemplosdesmbolosparabateras)
Pb
7/23/2019 XW NAS3 Operating Instructions
41/60
5Es
English
Franais
Espaol
Muchas gracias por la adquisicin de este productoPioneer.Lea todo este manual de instrucciones para aprender a operar correctamente su modelo.Despus de haber ledo las instrucciones, guarde el manual en un lugar seguro para poderlo
consultar en el futuro.
Contenido01 Antes de comenzarContenido de la caja. . . . . . . . . . . . . . . . . . . . .6Antes de emplear del mando a distancia. . . . . .6
Reemplace la pila . . . . . . . . . . . . . . . . . . . . . .6Uso del mando a distancia . . . . . . . . . . . . . . .7
Instalacin de la unidad . . . . . . . . . . . . . . . . . .7Enchufado. . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
02 Controles y pantallasMando a distancia. . . . . . . . . . . . . . . . . . . . . . .8Panel frontal/superior. . . . . . . . . . . . . . . . . . . .8
03 Reproduccin de iPodConfirme que los modelos de iPod seancompatibles . . . . . . . . . . . . . . . . . . . . . . . . . . .9Conexin del iPod. . . . . . . . . . . . . . . . . . . . . . .9
Conexin de un televisor . . . . . . . . . . . . . . . .10Reproduccin del iPod . . . . . . . . . . . . . . . . . .11
Uso de los controles de tono. . . . . . . . . . . . .11
04 ADAPTADOR Bluetooth para eldisfrute inalmbrico de la msicaReproduccin inalmbrica de msica . . . . . . .13
Funcionamiento con mando a distancia . . . .13Conexin del ADAPTADOR Bluetoothopcional . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Ajuste del cdigo PIN . . . . . . . . . . . . . . . . . . .14
Cmo emparejar el ADAPTADOR Bluetoothy el dispositivo de tecnologa inalmbricaBluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Audicin de contenidos musicales de undispositivo con tecnologa inalmbricaBluetoothcon su sistema . . . . . . . . . . . . . . . .15
05 Otras conexionesConexin de componentes auxiliares . . . . . . .16
06 Informacin adicionalResolucin de problemas . . . . . . . . . . . . . . . 17Restablecimiento del sistema . . . . . . . . . . . . 18Acerca del iPod/iPhone . . . . . . . . . . . . . . . . . 19Especificaciones. . . . . . . . . . . . . . . . . . . . . . 19Limpieza de la unidad . . . . . . . . . . . . . . . . . . 20
7/23/2019 XW NAS3 Operating Instructions
42/60
Antes de comenzar01
6Es
Captulo 1:
Antes de comenzarContenido de la cajaVerifique que los siguientes accesorios estn
en la caja al abrirla.
Mando a distancia
Soporte del mando a distancia
Pila de litio (CR2025) Cable de alimentacin
Pao de limpieza
Manual de instrucciones (este manual)
Antes de emplear del mando adistanciaEl mando a distancia se suministrada
colocado en el soporte del mando a distancia.
La pila que se suministra con esta unidad estguardada en el portapilas.
Saque la lmina de proteccin delportapilas.Cuando observe una disminucin en ladistancia operativa, recambie la pila (vasems abajo).
Reemplace la pilaCuando reemplace la pila, emplee una pila de
litio CR2025 de venta en los establecimientosdel ramo.
1 Presione la pestaa de liberacin a laizquierda para abrir el portapilas.
2 Tire hacia afuera del portapilas.
3 Saque la pila del portapilas.
4 Coloque una nueva pila en el portapilas.Asegrese de que el lado de la pila queda
mirando hacia arriba cuando lo coloque en el
espacio previsto para ello.
Precaucin
Recuerde las siguientes recomendacionescuando utilice pilas de litio:
Existe un peligro de explosin si se
reemplaza incorrectamente la pila. Recuerdeque slo puede recambiar pilas por otras del
mismo tipo o equivalente, de acuerdo con las
recomendaciones del fabricante.
Elimine las pilas usadas inmediatamente
despus de haberlas recambiado.
Mantngalas alejadas de los nios.
En caso de ingestin, pngase en contactocon su mdico inmediatamente.
Las pilas de litio pueden representar un
peligro de incendio o de quemadura qumicasi se utilizan mal. No desmonte ni calientems all de los 100 C, ni incinere la pila.
Quite la pila si la unidad no va a utilizarse
durante un mes o ms.
1
1
3
2