Xm Gtx6040 Sony Schematics

8/9/2019 Xm Gtx6040 Sony Schematics

1/22

SERVICE MANUAL

Sony CorporationAudio&Video Business Group

Published by Sony Techno Create Corporation

XM-GTX6040

SPECIFICATIONS

STEREO POWER AMPLIFIER

9-889-574-01

2009F04-1

© 2009.06

US Model

Canadian Model

Ver. 1.0 2009.06

Other Specifications

Circuit system OTL (output transformerless) circuit

Pulse power supply

Inputs RCA pin jacks High level input connector

Input level adjustment range

0.3 – 6 V (RCA pin jacks),

2.8 – 12 V (High level input)

Outputs Speaker terminals

Speaker impedance 2 – 8 Ω (stereo)

4 – 8 Ω (when used as a bridging amplifier)

Maximum output 4 Speakers: 110 W × 4 (at 4 Ω)

3 Speakers: 150 W × 2 (at 2 Ω) +

300 W × 1 (BTL, at 4 Ω)

Rated output (supply voltage at 14.4 V, 20 Hz – 20 kHz, 1 % THD)

4 Speakers:

60 W × 4 (at 4 Ω)

70 W × 4 (at 2 Ω)

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC DISTORTION

60 watts per channel minimum continuous average power into 4 ohms,

both channels driven from 20 Hz to 20 kHz with no more than 1 % total

harmonic distortion per Car Audio Ad Hoc Committee standards.

Frequency response 5 Hz – 50 kHz ( dB)

Harmonic distortion 0.05 % or less (at 1 kHz, 4 Ω)

Low-pass filter 80 Hz, 18 dB/octHigh-pass filter 80 Hz, 12 dB/oct

Power requirements 12 V DC car battery (negative ground)

Power supply voltage 10.5 – 16 V

Current drain at rated output: 33 A (4 Ω, 60 W × 4)

Remote input: 1 mA

Dimensions Approx. 384 × 55 × 252 mm

(15 1/8 × 2 1/4 × 10 in) (w/h/d) not incl.

projecting parts and controls

Mass Approx. 2.9 kg (6 lb 7 oz) not incl. accessories

Supplied accessories Mounting screws (4)

High level input cord (1)

Protection cap (1)

Design and specifications are subject to change without notice.

+0 –3


2/22

XM-GTX6040

2

SAFETY-RELATED COMPONENT WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTSWHOSE PART NUMBERS APPEAR AS SHOWN IN THISMANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR

LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DESPIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-TIONNEMENT. NE REMPLACER CES COMPOSANTS QUEPAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTSPUBLIÉS PAR SONY.

PROTECTOR OPERATION CHECK

Thermal Protect1. Short across TH901 with the power on.

2. Verify that the protector is operated and D918 illuminates

green. When input the signal and verify that there is no output

on the SP-OUT even when the volume is increased.

3. Verify that the protector is released and there is an output onthe SP-OUT when the short is removed.

4. Likewise, perform items 1 to 3 for TH902 and TH903.

Over Current Protect1. Short between the positive and negative sides of the speaker

output terminals CN903 and CN904 (1/2) with the power on.

(Perform this shorting for each channel on FRONT and

REAR.)

2. Verify that the protector is operated and D918 illuminates red.

3. Verify that the protector is not released and D918 remains red

even when the short is removed.

4. Verify that the protector is released and D918 illuminates

green when the power is turned off and then on again.

Offset Protect1. Short between the +12V terminal of CN904 (2/2) and the

(L+R) + or (L+R) – of the speaker output terminal CN904

(1/2).

(Short between +12V terminal and (L+R) + and between +12V

terminal and (L+R) –.)

2. Verify that the protector is operated and D918 illuminates red.

3. Verify that the protector is not released and D918 remains red

even when the short is removed.

4. Verify that the protector is released and D918 illuminates

green when the power is turned off and then on again.

Dimensions / Dimensions / Dimensiones

Unit: mm (in)

Unité : mm (po)

Unidad: mm

2 3 4

( 9 1

/ 4 )

2 5 2

( 1 0 )

313 (12 3/8)

55(2 1/4)384 (15 1/8)

ø 6 (1/4)313 (12 3/8)


3/22

XM-GTX6040

3

1. GENERAL Connections .................................................................... 4

2. DISASSEMBLY2-1. Bottom Plate ................................................................... 7

2-2. MAIN Board Section ...................................................... 8

2-3. MAIN Board ................................................................... 8

3. DIAGRAMS3-1. Block Diagram ................................................................ 11

3-2. Printed Wiring Board ...................................................... 12

3-3. Schematic Diagram –Main Section (1/2)– ...................... 13

3-4. Schematic Diagram –Main Section (2/2)– ...................... 14

4. EXPLODED VIEWS4-1. Heat Sink (Main) Section ............................................... 15

4-2. MAIN Board Section ...................................................... 16

5. ELECTRICAL PARTS LIST .............................. 17

TABLE OF CONTENTSUNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed withthe lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.• Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350 °C.

Caution: The printed pattern (copper foil) may peel away ifthe heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow)

than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

NOTES ON CHIP COMPONENT REPLACEMENT• Never reuse a disconnected chip component.

• Notice that the minus side of a tantalum capacitor may be dam-

aged by heat.


4/22

XM-GTX6040

4

SECTION 1

GENERAL This section is extractedfrom instruction manual.

Power Connection Wires (not supplied)

Câbles d’alimentation (non fournis)Cables de conexión de alimentación (no suministrados)

to a metal point of the carvers un point métallique de lacarrosseriea un punto metálico delautomóvil

Fuse (50 A)Fusible (50 A)Fusible (50 A)

+ 12 V car batteryBatterie de voiture + 12 VBatería de automóvil de + 12 V

Car audio unitAutoradio

Sistema de audio paraautomóvil

Remote output * 1

Télécommande* 1

Salida remota* 1

less than 450 mm (18 in)moins de 450 mm (18 po)menos de 450 mm

*2

*1 If you have the factory original or some other car audio unit without a remote output for the amplier, connect theremote input terminal (REMOTE) to the accessory power supply.

In High level input connection, car audio unit can also be activated without need for REMOTE connection. However, this

function is not guaranteed for all car audio units.

*1 Si vous disposez de l’autoradio d’origine ou d’un autre autoradio dont l’amplicateur ne comporte pas de sortie detélécommande, raccordez la borne d’entrée de commande à distance (REMOTE) à la prise d’alimentation accessoires.

Dans une connexion d’entrée à haut niveau, l’autoradio peut également être activé sans raccordement à REMOTE.

Toutefois, cette fonction n’est pas garantie pour tous les autoradios.

*1 Si dispone del sistema de audio para automóvil original de fábrica o de otro sistema sin una salida remota para elamplicador, conecte el terminal de e ntrada remota (REMOTE) a la fuente de alimentación auxiliar.

En la conexión de entrada de alto nivel, el sistema de audio para automóvil también puede activarse sin necesidad de

conexión REMOTE. No obstante, esta función no se garantiza en todos los sistemas de audio para automóvil.

Connections / Raccordements /ConexionesInstallation

Before Installationz Mount the unit either inside the trunk or under a

seat.z Choose the mounting location careully so the unit

will not interere with the normal movements o thedriver and it will not be exposed to direct sunlightor hot air rom the heater.

z Do not install the unit under the oor carpet, wherethe heat dissipation rom the unit will beconsiderably impaired.

First, place the unit where you plan to install it, andmark the positions o the 4 screw holes on the

mounting board (not supplied). Ten drill a 3 mm(1/8 in) pilot hole at each mark and mount the unitonto the board with the supplied mounting screws.Te mounting screws are all 15 mm (19/32 in) long, somake sure that the mounting board is thicker than15 mm (19/32 in).

Installation

Avant l’installationz Installez l’appareil dans le coffre ou sous un si ège.z Choisissez s oigneusement l’emplacement de

montage an d’éviter que l’appareil ne gêne leconducteur dans ses mouvements et qu’il ne soit pasexposé au rayonnement direct du soleil ou à l’airchaud du radiateur.

z N’installez pas l’appareil sous le tapis de sol car ladissipation thermique ne pourrait pas se airecorrectement.

Posez d’abord l’appareil à l’endroit où vous souhaitezl’installer et tracez un repère de p ositionnement pourles 4 orices de vis sur la plaque de montage (nonournie). Percez des orices de 3 mm (1/8 po) auniveau de chaque repère et xez l’appareil sur laplaque avec les vis de montage ournies. La longueurdes vis de montage est de 15 mm ( 19/32 po). Assurez-

vous donc que l’épaisseur de la plaque de montage estsupérieure à 15 mm (19/32 po).

Instalación

Antes de realizar la instalaciónz Monte la unidad en el interior del maletero o debajo

de un asiento.z Elija cuidadosamente el lugar de instalación de

orma que la unidad no diculte las maniobrasnormales del conductor y no quede expuesta a la luzsolar directa ni al aire caliente de la caleacción.

z No instale la unidad debajo de la moqueta del suelo,en cuyo caso la disipación de calor de la mismadisminuirá considerablemente.

En primer lugar, coloque la unidad donde tengaprevisto instalarla y marque sobre la supercie deltablero de montaje (no suministrado) las posi cionesde los 4 oricios para los tornillos. A continuación,perore los oricios con un diámetro deaproximadamente 3 mm y monte la unidad sobre eltablero con los tornillos de montaje suministrados. Yaque la longitud de estos tornillos es de 15 mm,compruebe que el grosor del tablero de montaje seasuperior a 15 mm.

Make the terminal connections as illustrated below.Effectuez les connexions des bornes comme illustré ci-dessous.Realice las conexiones de terminal como se ilustra a continuación.

3 3

c

Pass the wires through the cap, connect the wires, then cover the terminals with the cap.Note

When you tighten the screw, be careful not to apply too much torque* as doing so may damage the screw.* The torque value should b

Faites passer les ls par le cache, raccordez les ls, puis recouvrez les bornes avec le cache.Remarque

Lorsque vous vissez la vis, faites attention à ne pas appliquer une trop grande force* , car cela pourraitendommager la vis.* Le couple de serrage doit êtr

Pase los cables a través de la cubierta, conéctelos y cubra los terminales con dicha cubierta.Nota

Al apretar el tornillo, tenga cuidado de no aplicar demasiada fuerza de torsión* , ya que puede dañarlo.* El valor de fuerza de torsión deb

1Mount the unit as illustrated.Montez l’appareil comme illustré.Monte la unidad tal como se muestra en lailustración.

Cautionsz Beore making any connections, disconnect the

ground terminal o the car battery to avoid shortcircuits.

z Be sure to use speakers with an adequate powerrating. I you use small capacity speakers, they maybe damaged.

z Tis is a Phase-Inverted Amplier.z Do not connect the# terminal o the speaker

system to the car chassis, and do not connect the # terminal o the right speaker with that o the lefspeaker.

z Install the input and output cords away rom thepower supply wire as running them close togethercan generate some intererence noise.

z Tis unit is a high powered amplier. Tereore, itmay not perorm to its ull potential i used with thespeaker cords supplied with the car.

z I your car is equipped with a computer system ornavigation or some other purpose, do not removethe ground wire rom the car battery. I youdisconnect the wire, the computer memory may beerased. o avoid short circuits when makingconnections, disconnect the + 12 V power supplywire until all the other wires have been connected.

Avertissementz Avant d’effectuer les raccordements, débranchez la

borne de mise à la terre de la batterie de voiturepour éviter de provoquer un court-circuit.

z Utilisez des haut-parleurs d’une capacité adéquate.Si vous utilisez des haut-parleurs de aible capacité,

ils risquent d’être endommagés.z Les phases de cet amplicateur sont inversées.z Ne raccordez pas la borne# du système de

hautparleurs à la carrosserie de la voiture, ou la borne# du haut-parleur droit à celle du haut-parleur gauche.

z Eloignez les cordons d’entrée et de sortie du ld’alimentation électrique an d’éviter que desinterérences ne se produisent.

z Cet appareil est un amplicateur de haute puissance.Il se peut donc qu’il n’atteigne pas sa puissancemaximale s’il est utilisé avec les cordons de haut-parleurs de la voiture.

z Si votre voiture est équipée d’un ordinateur de bord

pour la navigation ou autre, ne débranchez pas le lde masse de la batterie de la voiture. Si vousdébranchez ce l, toute la mémoire de l’ordinateurrisque d’être effacée. Pour éviter tout risque de court-circuit lorsque vous effectuez les raccordements,branchez le l d’alimentation de + 12 V uniquementaprès avoir branché tous les autres ls.

Precauciónz Antes de realizar las conexiones, desconecte el

terminal de toma a tierra de la batería del automóvilpara evitar cortocircuitos.

z Asegúrese de utilizar altavoces con una potencianominal adecuada. Si emplea altavoces de capacidadreducida, pueden dañarse.

z Este amplicador es de ase invertida.z No conecte el terminal# del sistema de altavoces al

chasis del automóvil, ni el terminal# del altavozderecho al del altavoz izquierdo.

z Instale los cables de entrada y salida alejados delcable de la uente de alimentación, ya que en casocontrario puede generarse ruido por intererencias.

z Esta unidad es un amplicador de alta potencia. Portanto, puede no uncionar a pleno rendimiento si seutiliza con los cables de altavoz suministrados con elautomóvil.

z Si el automóvil está equipado con un sistema deordenador para la navegación o para otra nalidad,no desconecte el conductor de toma a tierra de labatería del automóvil. Si lo desconecta, la memoriadel ordenador puede borrarse. Para evitarcortocircuitos al realizar las conexiones, desconecteel cable de la uente de alimentación de + 12 V hastaconectar todos los cables.

Notes on the power supply z Connect the + 12 V power supply wire only after all the other

wires have been connected.z Be sure to connect the ground wire of the unit securely to

a metal point of the car. A loose connection may cause a

malfunction of the amplier.z Be sure to connect the remote control wire of the car audio

unit to the remote terminal.z When using a car audio unit without a remote output on the

amplier, connect the remote input terminal (REMOTE) tothe accessory power supply.z Use a power supply wire with a fuse attached (50 A).

z All power wires connected to the positive battery post

should be fused within 450 mm (18 in) of the battery post,

and before they pass through any metal.z Make sure that the vehicle’s battery wires connected to the

vehicle (ground to chassis)* 2 are of a wire gauge at least

equal to that of the main power wire connected from the

battery to the amplier.z During full-power operation, a current of more than 50 A

will run through the system. Therefore, make sure that the

wires to be connected to the+ 12 V

andGND

terminals ofthis unit are at least 10-Gauge (AWG-10) or have a sectional

area of more than 5 mm 2 ( 7 / 32 in2 ).

Remarques sur l’alimentation électriquez Raccordez le câble d’alimentation + 12 V uniquement après

avoir réalisé toutes les autres connexions.z Raccordez solidement le l de mise à la terre de l’appareil

à un point métallique de la carrosserie. Une connexion

lâche risque de provoquer un problème de

fonctionnement de l’amplicateur.z Veillez à raccorder le l de commande à distance de

l’autoradio à la borne de commande à distance.z Si vous utilisez un autoradio dont l’amplicateur ne

comporte pas de sortie de commande à distance, raccordez

la borne d’entrée de commande à distance (REMOTE) à la

prise d’alimentation accessoires.z Utilisez un câble d’alimentation doté d’un fusible (50 A).

z Tous les ls électriques raccordés à la borne positive de la

batterie doivent être protégés par un fusible à une distance

maximum de 450 mm (18 po) à la borne de la batterie et

avant de passer dans une partie métallique quelconque.z Assurez-vous que les ls de la batterie du véhicule raccordés

à ce dernier (l de mise à la terre au châssis)* 2 sont d’un

calibre au moins égal à celui du l électrique principal

reliant la batterie et l’amplicateur.z Pendant une utilisation à pleine puissance, un courant d’une

intensité supérieure à 50 A circule dans le système. Assurez-

vous que les câbles à raccorder aux bornes + 12 V et GND de

cet appareil sont de calibre supérieur à 10 (AWG-10) ou

d’une section supérieure à 5 mm 2 ( 7 / 32 po2 ).

Notas sobre la fuente de alimentaciónz Conecte el cable de la fuente de alimentación de + 12 V sólo

después de haber conectado los otros cables.z Asegúrese de conectar rmemente el cable de toma a

tierra de la unidad a un punto metálico del automóvil.

Una conexión oja puede causar fallos de

funcionamiento del amplicador.z Compruebe que conecta el cable de control remoto del

sistema de audio para automóvil al terminal remoto.z

Si utiliza un sistema de audio para automóvil sin salidaremota en el amplicador, conecte el terminal de entrada

remota (REMOTE) a la fuente de alimentación auxiliar.z Emplee el cable de la fuente de alimentación con un fusible

jado (50 A).

z Todos los cables de alimentación conectados al polo

positivo de la batería deben conectarse a un fusible situado

a menos de 450 mm del polo de la batería, y antes de pasar

por ninguna pieza metálica.z Asegúrese de que los cables de la batería del vehículo

conectados al mismo (a la masa del chasis)* 2 tienen una

anchura igual o superior a la del cable de alimentación

principal que conecta la batería con el amplicador.z Durante el funcionamiento a pleno rendimiento, uye por el

sistema una corriente superior a 50 A. Por tanto, compruebeque los cables que va a conectar a los terminales de + 12 V y

GND de esta unidad son del calibre 10 (AWG 10) como

mínimo o presentan un área de sección superior a 5 mm 2.


5/22

XM-GTX6040

5

BHigh Level Input ConnectionConnexion d’entrée à haut niveauConexión de entrada de alto nivel

Line Input ConnectionConnexion d’entrée de ligneConexión de entrada de línea

A

Input Connections / Connexions d’entrée / Conexiones de entrada

RearArrière Traseros

FrontAvantDelanteros

Car audio unit

AutoradioSistema de audio paraautomóvil

LINE OUTLINE OUT

Front right speaker output

Sortie du haut-parleur avant droitSalida del altavoz delantero derecho

Rear right speaker output

Sortie du haut-parleur arrière droitSalida del altavoz trasero derecho

Car audio unitAutoradio

Sistema de audio paraautomóvil

WhiteBlancBlanco

GreyGrisGris

2

GreenVertVerde

PurpleMauveVioleta

Front left speaker outputSortie du haut-parleur avant gaucheSalida del altavoz delantero izquierdo

Rear left speaker outputSortie du haut-parleur arrière gaucheSalida del altavoz trasero izquierdo

StripedRayéCon rayas




High Level Input ConnectorConnecteur d’entrée à haut niveauConector de entrada de alto nivel

GreyGrisGris

WhiteBlancBlanco

Striped/WhiteRayé/BlancCon rayas/Blanco

Striped/GreyRayé/GrisCon rayas/Gris

GreenVertVerde

PurpleMauveVioleta

Striped/PurpleRayé/MauveCon rayas/Violeta

Striped/GreenRayé/VertCon rayas/Verde


6/22

XM-GTX6040

6

4-Speaker System

Système à 4 haut-parleursSistema de 4 altavoces1

3-Speaker System

Système à 3 haut-parleursSistema de 3 altavoces2

Speaker Connectionsurn on or off the LPF and HPF switch at the unit rear as illustrated below.

Raccordement des haut-parleursRéglez le commutateur LPF et HPF situé à l’arrière de l’appareil à On ou Off, comme indiqué dans l’illustration ci-dessous.

Conexiones de los altavocesEncienda o apague los interruptores LPF y HPF situados en la parte posterior de la unidad, como se muestra a continuación.

Notesz In this system, the volume of the subwoofer will be

controlled by the car audio unit fader control.z In this system, the output signals to the subwoofer will

be the combination of both the REAR L and R INP UT

jacks or the REAR high level input connector signals.

Remarquesz Dans ce système, le volume du caisson de graves est

contrôlé par la commande de balance avant/arrière de

l’autoradio.z Dans ce système, les signaux émis vers le caisson de

graves sont constitués des signaux des prises REAR L et R

INPUT ou des signaux du connecteur d’entrée de haut

niveau REAR.

Notasz En este sistema, el volumen del altavoz potenciador de

graves se controla mediante el control de equilibrio

entre altavoces del sistema de audio para automóvil.z En este sistema, las señales de salida que recibe el

altavoz potenciador de graves serán la combinación de

las tomas REAR L y R INPUT o de las señales del conector

de entrada de alto nivel REAR.

Note

In this system, the volume of the subwoofer will be controlled by the car audio unit fader control.

Remarque

Dans ce système, le volume du caisson de graves est contrôlé par la commande de balance avant/arrière de

l’autoradio.

Nota

En este sistema, el volumen del altavoz potenciador de graves se controla mediante el control de equilibrio entre

altavoces del sistema de audio para automóvil.

OFF

HPF(80Hz)

ON OFF

LPF(80Hz)

ON

Front speaker (min. 2 Ω)Haut-parleurs avant (min. 2 )Altavoces delanteros (mín. 2 )

Rear speaker (min. 2 Ω)Haut-parleurs arrière (min. 2 )Altavoces traseros (mín. 2 )

LeftgaucheIzquierdo

RightDroitDerecho

LeftgaucheIzquierdo

RightDroitDerecho

OFF

HPF(80Hz)

ON OFF

LPF(80Hz)

ON

Subwoofer (min. 4 Ω)Caisson de graves (mín. 4 Ω)Altavoz potenciador de graves (mín. 4 Ω)

Full range speakers (min. 2 Ω)Hauts-parleurs pleine gamme (min. 2 Ω)Altavoces de gama completa (mín. 2 Ω)Left

gaucheIzquierdo

RightDroitDerecho

OFF

HPF(80Hz)

ON OFF

LPF(80Hz)

ON

Subwoofer (min. 2 Ω)Caisson de graves (min. 2 Ω)Altavoz potenciador de graves (mín. 2 Ω)

Full range speakers (min. 2 Ω)Hauts-parleurs pleine gamme (min. 2 )Altavoces de gama completa (mín. 2 )

LeftgaucheIzquierdo

RightDroitDerecho

LeftgaucheIzquierdo

RightDroitDerecho

2-Way SystemSystème 2 voiesSistema de 2 vías

3


7/22

XM-GTX6040

7

SECTION 2

DISASSEMBLY

• This set can be disassembled in the order shown below.

Note: Follow the disassembly procedure in the numerical order given.

2-1. BOTTOM PLATE

2-1. BOTTOM PLATE

(Page 7)

2-2. MAIN BOARD SECTION

(Page 8)

SET

2-3. MAIN BOARD

(Page 8)

1 three screws (+B, TT, B-type, 3 6)

2 three screws (+B, TT, B-type, 3 6)

3 screw (+BVTP S3 6)

4 bottom plate


8/22

XM-GTX6040

8


2-3. MAIN BOARD

5 MAIN board section

main heat sink

2 three screws (+P, TT, B-type, 3 8)

3 three screws

(+P, TT, B-type, 3

8)


1 screw (+B, TT, B-type, 3 6)

4 front panel

5 MAIN board


2 screw

(+P, TT, B-type, 3

8)

3 screw (+P, TT, B-type, 3 8)


9/22

XM-GTX6040

9

SECTION 3

DIAGRAMS

THIS NOTE IS COMMON FOR PRINTED WIRING

BOARDS AND SCHEMATIC DIAGRAMS.

(In addition to this, the necessary note is printed

in each block.)

For Printed Wiring Boards.

Note:• X : Parts extracted from the component side.• : Pattern from the side which enables seeing.

• Indication of transistor.

C

These are omitted.

B E

For Schematic Diagrams.Note:

• All capacitors are in μF unless otherwise noted. (p: pF) 50

WV or less are not indicated except for electrolytics and

tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwise

specified.

• A : B+ Line.• B : B– Line.• H: Adjustment for repair.• Power voltage is dc 14.4 V and fed with regulated dc

power supply from +12 V and REM terminals.

• Voltages are dc with respect to ground under no-signal

conditions.• Voltages are taken with VOM (Input impedance 10 MΩ).

Voltage variations may be noted due to normal production

tolerances.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal production

tolerances.

• Circled numbers refer to waveforms.

• Signal path.

F : AUDIO

Note:

The components identi-

fied by mark 0 or dottedline with mark0 are criti-cal for safety.

Replace only with part

number specified.

Note:

Les composants identifiés

par une marque 0 sontcritiques pour la sécurité.

Ne les remplacer que par

une pièce portant le nu-

méro spécifié.

• Note for Replacement of the Transistors

The transistors Q110, 111, 210, 211, 310, 311, 410 and 411 have

two different ranks: P rank and Y rank.

The rank of these transistors need to be selected properly accord-

ing to each channel. When replacing any one of these transistors,

check its rank and replace with the appropriate transistor of the

same rank.

Rank Q110, 210, 310, 410 Q111, 211, 311, 411

P2SC5100-P

(8-729-024-79)

2SA1908-P

(8-872-024-76)

Y2SC5100-Y

(8-729-024-80)

2SA1908-Y

(8-872-024-77)

DISCRIMINATION:

A1908: 2SA1908

C5100: 2SC5100

P: RANK P

Y: RANK Y


10/22

XM-GTX6040

10

• IC Block Diagram• Waveform

1 IC9035 (CT)

1 V/DIV, 10 sec/DIV

3.3 Vp-p

18 sec

IC903 TL594INSR (MAIN Board (2/2))

OSC

REF 5V

ERROR

ERROR

0.1V

Q1Q2

16 15 14 13 12 11 10 9

1 2 3 4 5 6 7 8

N O N

I N V

V R E F

V C C

C 2

E 1

E 2

O U T

+ I N - I

N

C O M P E N

C T

R T

C 1

G N D

T I M E


11/22


12/22


13/22

XM-GTX6040

XM-GTX6040

1313

3-3. SCHEMATIC DIAGRAM – MAIN Section (1/2) –

R202

R402

R 8 0 2 C801R801

R 80 3 C 80 3

R8 04 C8 04

R102

R103

R101

C 2 0 1

C 2 0 2

R201

R301

R401

C108 C109

C111

C110

R203

C205

C206

C207

C208

C210

C211

C112 R151

R251

R302

R303

R403

C 3 0 1

C 3 0 2

C 4 0 1

C 4 0 2

C305

C306

C307

C808

C407

C405

C815

C809

C308

C408

C311

C312

C411

R351

R451

C412

R153 R161

R159

R162

C154

R160

R166

R167

R169

R168

R259

R 253 R 261

R262

R260

C254

R267

R269

R268

R 35 3 R 361

R362

R360

R359

C354

R366

R367

R369

R368

R453

R459

R461

R462

R460

C454

R466

R467

R468

R469

R172

R272

R372

R472

C106

C105

C107

C209

C406

R266

C212

VR801

VR801

VR802

VR802

R 10 4 R 10 5R806

R816

R817

R818

C116

C117

C216 C217

C417

C416

C317 C316

R205 R204

R305 R304

C 8 0 2

R4 04 R 405

Q201

Q101

Q301

Q401

C 1 0 1

C 1 0 2

C151

C251

C351

C451

CN901

CNJ101

CN903

R106 R107

R207

R206

R208

R212

R112

R308 R311

R307

R306

R312

R412

R411R408

R407

R406

R163R177

R263

R363

R463

R277

R477

R377

R108CNJ101

CNJ101

IC801(1/2)

IC801(2/2)

IC803(2/2)

IC803(1/2)

IC805(1/2)

IC805(2/2)

S801

R113

R213

R252

R152

JC727

JC732

JC726

TP10

JC722 JC721

D906

D907

IC802(1/2) C309

IC804(1/2)

IC806(1/2)

IC806(2/2)

IC804(2/2)

IC802(2/2)

JC716

S802

R313 JC719

JC724

JC720

JC715

R352

R452

JC717

JC723

JC718

R413

C310

C410

C409

TP15

TP14

TP13

TP12

TP09

TP08

TP07

TP06

C455

C355

C255

C155

Q102

Q202

Q302

Q402

Q403

Q303

Q203

Q103Q104

Q204

Q304

Q404

Q405

Q305

Q205

Q105

Q107

Q207

Q307

Q407

Q409

Q309

Q209

Q109

Q108

Q208

Q308

Q408

Q411

Q311

Q211

Q111

Q110

Q210

Q310

Q410Q412

Q312

Q212

Q112C152

C153

R154

R165

C252

C253

R265

R254

C352

C353

R365

R354

C452 R465

C453

R454

JC728

JC730

JC729

JC731

R109

R209

R111

R211

R110

R210

R309 R310

R409 R410

R944

R946

R945

R943

R155 R1 58 R 17 5

R156

R 15 7 R 17 6

R164 Q106 R178

R170

R171

R255 R 25 8 R 27 5

R 25 7 R 27 6

R256

R264 Q206 R278

R270

R271

R355R 35 8 R 37 5

R 35 7 R 37 6

R356

R364 Q306 R378

R370

R371

R455R 45 8 R 47 5

R 45 7 R 47 6

R456

R464 Q406 R478

R470

D101

D102

D201

D202

D301

D302

D401

D402

CN904

R471

(Page 14)


14/22

XM-GTX6040

XM-GTX6040

1414

• See page 10 for waveform and IC Block Diagram.3-4. SCHEMATIC DIAGRAM – MAIN Section (2/2) –

IC B/D

JW

F901

R912

F902

R919

C909

R934 C911

R809

C904

C906

C907C903

C901

R903

R902

R901

C917

R 805 C80 5

R928

R931

R920

R921

R929

R930C913

C914

C817

C818

C819

C821

C820

C822 C823

R814

R815

C824

C825

C826

C827

C811 C813

C814

C915

C916

R932

R933

R914

C918

L901

R940

C908

C902 C 81 2 R 81 3

R812

R807

C810

T901

T H 9 0 3

T H 9 0 2

T H 9 0 1

L801

IC902

R941

R 9 0 9

Q812 Q811 Q809 Q810

Q802

D801

JC725

JC701

R926

R927

Q908

Q909

Q910

Q912

Q911

Q913

Q807

Q808

D805

D806

D803

D804

JC714

TP26

TP27

TP22

TP23

TP24

TP25TP29

TP28

JC710

JC712

JC708 JC707JC709 JC704

JC703 JC702

JC713

JC711

JC705

TP05

TP01

TP04 TP903

TP902

TP901

TP30

Q905

Q907

Q906 D905

Q915

Q914

D901

IC903 Q902

Q901

D807

Q803

Q804

Q805

Q806

R 9 0 8

R 9 0 7

C919

R939

C910

TP19

D902

D904

Q903

D802

R808

R923

R922

R924

R925

C912

CN904

R917

R918

R942

R915

R916

C920

R937

R938

R936

R935

R910 C905

R 9 1 1

R904

R905

D918

R810

R811

JC706

(Page 13)


15/2215

XM-GTX6040

SECTION 4

EXPLODED VIEWS

1 4-144-883-01 PLATE, TOP

2 4-144-882-01 HEAT SINK (MAIN)

3 3-273-612-31 SCREW (+B, TT, B-TYPE, 3X14)

4 3-273-612-12 SCREW (+B, TT, B-TYPE, 3X8)

5 3-277-208-11 SCREW (+P, TT, B-TYPE, 3X8)

6 4-144-884-01 PLATE, BOTTOM

7 3-273-612-01 SCREW (+B, TT, B-TYPE, 3X6)

8 2-580-628-01 SCREW, +BVTP S3X6 TYPE2

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

Note:

• Items marked “*” are not stocked since

they are seldom required for routine ser-

vice. Some delay should be anticipated

when ordering these items.

• The mechanical parts with no reference

number in the exploded views are not sup-

plied.

• Color Indication of Appearance Parts Ex-

ample:

KNOB, BALANCE (WHITE) . . . (RED)

↑ ↑

Parts Color Cabinet’s Color

• Accessories are given in the last of the

electrical parts list.

4-1. HEAT SINK (MAIN) SECTION

The components identified by mark 0

or dotted line with mark 0 are critical for

safety.

Replace only with part number specified.

Les composants identifiés par une marque

0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce por-

tant le numéro spécifié.

1

2

3

4

5

5

5

7

6

7

7

8

MAIN board section


16/2216

XM-GTX6040



51 A-1219-711-B MAIN BOARD, COMPLETE

52 3-225-184-12 SCREW (+PS.TT.3X8)

53 2-693-613-21 PANEL, FRONT

54 3-912-431-01 SCREW (+-P)

55 3-277-208-11 SCREW (+P, TT, B-TYPE, 3X8)

D803 8-719-079-00 DIODE FCH10A15

D804 8-719-079-01 DIODE FRH10A15

0 F901 1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A)


v Q110 8-729-024-79 TRANSISTOR 2SC5100-P

v Q110 8-729-024-80 TRANSISTOR 2SC5100-Y

v Q111 8-729-024-76 TRANSISTOR 2SA1908-Pv Q111 8-729-024-77 TRANSISTOR 2SA1908-Y



v Q211 8-729-024-76 TRANSISTOR 2SA1908-P

v Q211 8-729-024-77 TRANSISTOR 2SA1908-Y









Q910 6-550-341-01 FET FKV550N

Q911 6-550-341-01 FET FKV550N Q912 6-550-341-01 FET FKV550N

Q913 6-550-341-01 FET FKV550N

#1 7-685-646-79 SCREW +P 3X8 TYPE2 NON-SLIT

v Refer to page 9 for Note for Replacement of the Transistors.

not supplied

not supplied

not supplied

#1

D804, D803

Q311, Q310,

Q411, Q410

Q111, Q110,

Q211, Q210

Q911, Q910, Q912, Q913

51

52

52

5252

54

5454

52

52

52

53

55

55 55

F901

F902


17/2217

XM-GTX6040

SECTION 5

ELECTRICAL PARTS LIST

A-1219-711-B MAIN BOARD, COMPLETE

*********************

3-225-184-12 SCREW (+PS.TT.3X8)

3-912-431-01 SCREW (+-P) 7-685-646-79 SCREW +P 3X8 TYPE2 NON-SLIT

< CAPACITOR >

C101 1-162-927-11 CERAMIC CHIP 100PF 5% 50V





C108 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V


C110 1-126-933-11 ELECT 100uF 20% 16V

C111 1-126-963-11 ELECT 4.7uF 20% 50V




C151 1-126-947-11 ELECT 47uF 20% 35V



C154 1-126-960-11 ELECT 1uF 20% 50V

C155 1-136-161-00 FILM 0.047uF 5% 50V






C208 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C209 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C210 1-126-933-11 ELECT 100uF 20% 16V

C211 1-126-963-11 ELECT 4.7uF 20% 50V




C251 1-126-947-11 ELECT 47uF 20% 35V



C254 1-126-960-11 ELECT 1uF 20% 50V

C255 1-136-161-00 FILM 0.047uF 5% 50V






C308 1-126-960-11 ELECT 1uF 20% 50V



C311 1-126-933-11 ELECT 100uF 20% 16V




C351 1-126-947-11 ELECT 47uF 20% 35V



C354 1-126-960-11 ELECT 1uF 20% 50V

C355 1-136-161-00 FILM 0.047uF 5% 50V





C407 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C408 1-126-960-11 ELECT 1uF 20% 50V



C411 1-126-933-11 ELECT 100uF 20% 16V




C451 1-126-947-11 ELECT 47uF 20% 35V



C454 1-126-960-11 ELECT 1uF 20% 50V

C455 1-136-161-00 FILM 0.047uF 5% 50V


C802 1-126-934-11 ELECT 220uF 20% 16V






C810 1-126-965-11 ELECT 22uF 20% 50V



C813 1-104-655-11 ELECT 470uF 20% 6.3V

C814 1-104-655-11 ELECT 470uF 20% 6.3V

C815 1-126-933-11 ELECT 100uF 20% 16V

C817 1-162-974-11 CERAMIC CHIP 0.01uF 50V



When indicating parts by reference num-

ber, please include the board name.

Note:

• Due to standardization, replacements in

the parts list may be different from the

parts specified in the diagrams or the com-

ponents used on the set.

• Items marked “*” are not stocked since

they are seldom required for routine ser-

vice. Some delay should be anticipated

when ordering these items.

• RESISTORS

All resistors are in ohms.

METAL: Metal-film resistor.

METAL OXIDE: Metal oxide-film resistor.

F: nonflammable

• CAPACITORS

uF: μF

• COILS

uH: μH

• SEMICONDUCTORS

In each case, u: μ, for example:

uA. . : μ A. . , uPA. . , μPA. . ,

uPB. . : μPB. . , uPC. . , μPC. . ,

uPD. . : μPD. .

The components identified by mark 0

or dotted line with mark 0 are critical for

safety.

Replace only with part number specified.

Les composants identifiés par une marque

0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce por-

tant le numéro spécifié.

MAIN


18/22


XM-GTX6040

18

C819 1-165-949-41 ELECT 1500uF 20% 35V

C820 1-165-949-41 ELECT 1500uF 20% 35V

C821 1-165-949-41 ELECT 1500uF 20% 35V

C822 1-165-949-41 ELECT 1500uF 20% 35V


C824 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C825 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C826 1-126-933-11 ELECT 100uF 20% 16V

C827 1-126-933-11 ELECT 100uF 20% 16V

C901 1-100-352-11 CERAMIC CHIP 1uF 20% 16V




C905 1-130-471-00 MYLAR 0.001uF 5% 50V

C906 1-126-933-11 ELECT 100uF 20% 16V


C908 1-126-933-11 ELECT 100uF 20% 16V


C910 1-137-194-81 FILM 0.47uF 5% 50V


C912 1-136-161-00 FILM 0.047uF 5% 50V

C913 1-131-731-12 ELECT 2200uF 20% 16V

C914 1-131-731-12 ELECT 2200uF 20% 16V




C918 1-100-352-11 CERAMIC CHIP 1uF 20% 16V


C920 1-126-965-11 ELECT 22uF 20% 50V

< CONNECTOR >

CN901 1-580-283-11 PIN, CONNECTOR (PC BOARD) 8P (HIGH LEVEL INPUT (SENSING POWER ON))

< TERMINAL BOARD >

CN903 1-780-132-11 TERMINAL BOARD (4P) (FRONT SPEAKER OUT)

CN904 1-780-134-12 TERMINAL BOARD (4P+3P+2FUSE)

(REAR SPEAKER OUT,REM,+12V,GND,25A,25A)

< JACK >

CNJ101 1-779-078-21 JACK, PIN 4P (INPUT)

< DIODE >

D101 8-719-988-61 DIODE 1SS355TE-17

D102 8-719-988-61 DIODE 1SS355TE-17

D201 8-719-988-61 DIODE 1SS355TE-17

D202 8-719-988-61 DIODE 1SS355TE-17

D301 8-719-988-61 DIODE 1SS355TE-17

D302 8-719-988-61 DIODE 1SS355TE-17

D401 8-719-988-61 DIODE 1SS355TE-17

D402 8-719-988-61 DIODE 1SS355TE-17

D801 8-719-978-33 DIODE DTZ-TT11-6.8B

D802 8-719-914-43 DIODE DAN202K

D803 8-719-079-00 DIODE FCH10A15

D804 8-719-079-01 DIODE FRH10A15

D805 8-719-083-63 DIODE UDZSUSTE-1713B


D807 8-719-914-43 DIODE DAN202K

D901 8-719-914-43 DIODE DAN202K

D902 8-719-914-43 DIODE DAN202K


D905 8-719-914-43 DIODE DAN202K

D906 8-719-914-43 DIODE DAN202K

D907 8-719-914-43 DIODE DAN202K

D918 8-719-025-62 LED SML1216WTP4 (POWER/PROTECTOR)

< FUSE >



< IC >

IC801 8-759-710-97 IC NJM4565M-D

IC802 8-759-710-97 IC NJM4565M-D

IC803 8-759-710-97 IC NJM4565M-D

IC804 8-759-710-97 IC NJM4565M-D

IC805 8-759-710-97 IC NJM4565M-D

IC806 8-759-710-97 IC NJM4565M-D

IC902 6-600-354-01 IC PC-17K1

IC903 6-703-643-01 IC TL594INSR

< JUMPER RESISTOR >

JC701 1-216-296-11 SHORT CHIP 0

JC702 1-216-296-11 SHORT CHIP 0

JC703 1-216-296-11 SHORT CHIP 0

JC704 1-216-296-11 SHORT CHIP 0

JC705 1-216-296-11 SHORT CHIP 0

JC706 1-216-296-11 SHORT CHIP 0

JC707 1-216-296-11 SHORT CHIP 0

JC708 1-216-296-11 SHORT CHIP 0

JC709 1-216-296-11 SHORT CHIP 0

JC710 1-216-296-11 SHORT CHIP 0

JC711 1-216-296-11 SHORT CHIP 0 JC712 1-216-296-11 SHORT CHIP 0

JC713 1-216-296-11 SHORT CHIP 0

JC714 1-216-296-11 SHORT CHIP 0

JC715 1-216-296-11 SHORT CHIP 0

JC716 1-216-296-11 SHORT CHIP 0

JC717 1-216-296-11 SHORT CHIP 0

JC718 1-216-296-11 SHORT CHIP 0

JC719 1-216-296-11 SHORT CHIP 0

JC720 1-216-296-11 SHORT CHIP 0

JC721 1-216-296-11 SHORT CHIP 0

JC722 1-216-296-11 SHORT CHIP 0

JC723 1-216-864-11 SHORT CHIP 0

JC724 1-216-864-11 SHORT CHIP 0

JC725 1-216-864-11 SHORT CHIP 0

JC726 1-216-296-11 SHORT CHIP 0

JC727 1-216-296-11 SHORT CHIP 0

JC728 1-216-864-11 SHORT CHIP 0

JC729 1-216-864-11 SHORT CHIP 0

JC730 1-216-296-11 SHORT CHIP 0

JC731 1-216-296-11 SHORT CHIP 0

JC732 1-216-864-11 SHORT CHIP 0

< COIL >

L901 1-411-756-22 COIL, CHOKE 50uH

< TRANSISTOR >

Q101 6-550-686-01 TRANSISTOR KTC2875-B-RTK

Q102 8-729-014-85 TRANSISTOR 2SA1618-YGRTE85R

MAIN


19/22


XM-GTX6040

1919

Q103 8-729-014-87 TRANSISTOR 2SC4207(T5RSONY,F)

Q104 8-729-140-82 TRANSISTOR 2SA988-PAFAEA

Q105 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA

Q106 8-729-041-66 TRANSISTOR 2SC4015TV2

Q107 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R

Q108 8-729-020-80 TRANSISTOR 2SC2235-O/Y(TPE6) Q109 8-729-232-32 TRANSISTOR 2SA965



Q112 8-729-120-28 TRANSISTOR 2SC1623-L5L6








Q208 8-729-020-80 TRANSISTOR 2SC2235-O/Y(TPE6)

Q209 8-729-232-32 TRANSISTOR 2SA965












Q309 8-729-232-32 TRANSISTOR 2SA965

v Q310 8-729-024-79 TRANSISTOR 2SC5100-Pv Q311 8-729-024-76 TRANSISTOR 2SA1908-P










Q409 8-729-232-32 TRANSISTOR 2SA965









Q807 8-729-209-15 TRANSISTOR 2SD2012

Q808 8-729-209-60 TRANSISTOR 2SB1375

Q809 8-729-027-23 TRANSISTOR DTA114EKA-T146




Q901 8-729-027-43 TRANSISTOR DTC114EKA-T146 Q902 8-729-027-38 TRANSISTOR DTA144EKA-T146

Q903 8-729-027-43 TRANSISTOR DTC114EKA-T146

Q905 8-729-052-82 TRANSISTOR KTA1281Y-AT


Q907 8-729-027-43 TRANSISTOR DTC114EKA-T146



Q910 6-550-341-01 FET FKV550N Q911 6-550-341-01 FET FKV550N

Q912 6-550-341-01 FET FKV550N

Q913 6-550-341-01 FET FKV550N



< RESISTOR >

R101 1-216-206-00 METAL CHIP 2.2K 5% 1/8W

R102 1-216-837-11 METAL CHIP 22K 5% 1/10W

R103 1-216-837-11 METAL CHIP 22K 5% 1/10W

R104 1-216-849-11 METAL CHIP 220K 5% 1/10W

R105 1-216-849-11 METAL CHIP 220K 5% 1/10W

R106 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R107 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R108 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R109 1-218-882-11 METAL CHIP 30K 0.5% 1/10W

R110 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R111 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R112 1-218-843-11 METAL CHIP 680 0.5% 1/10W

R113 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W

R151 1-216-222-00 METAL CHIP 10K 5% 1/8W

R152 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R153 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R154 1-216-222-00 METAL CHIP 10K 5% 1/8W

R155 1-216-839-11 METAL CHIP 33K 5% 1/10W

R156 1-216-839-11 METAL CHIP 33K 5% 1/10W R157 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R158 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R159 1-216-809-11 METAL CHIP 100 5% 1/10W

R160 1-216-809-11 METAL CHIP 100 5% 1/10W

R161 1-216-845-11 METAL CHIP 100K 5% 1/10W

R162 1-216-845-11 METAL CHIP 100K 5% 1/10W

R163 1-218-843-11 METAL CHIP 680 0.5% 1/10W

R164 1-218-831-11 METAL CHIP 220 0.5% 1/10W

R165 1-216-837-11 METAL CHIP 22K 5% 1/10W

R166 1-216-182-00 METAL CHIP 220 5% 1/8W

R167 1-216-134-00 METAL CHIP 2.2 5% 1/8W

R168 1-216-134-00 METAL CHIP 2.2 5% 1/8W

R169 1-205-991-11 ENCAPSULATED COMPONENT 0.1X2 5W

R170 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R171 1-216-844-11 METAL CHIP 82K 5% 1/10W

R172 1-216-134-00 METAL CHIP 2.2 5% 1/8W

R175 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R176 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R177 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R178 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R201 1-216-206-00 METAL CHIP 2.2K 5% 1/8W

R202 1-216-837-11 METAL CHIP 22K 5% 1/10W

R203 1-216-837-11 METAL CHIP 22K 5% 1/10W

R204 1-216-849-11 METAL CHIP 220K 5% 1/10W

R205 1-216-849-11 METAL CHIP 220K 5% 1/10W

R206 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R207 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R208 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

v Refer to page 9 for Note for Replacement of the Transistors.

MAIN


20/22


XM-GTX6040

20

R209 1-218-882-11 METAL CHIP 30K 0.5% 1/10W

R210 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R211 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R212 1-218-843-11 METAL CHIP 680 0.5% 1/10W

R213 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W

R251 1-216-222-00 METAL CHIP 10K 5% 1/8W R252 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R253 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R254 1-216-222-00 METAL CHIP 10K 5% 1/8W

R255 1-216-839-11 METAL CHIP 33K 5% 1/10W

R256 1-216-839-11 METAL CHIP 33K 5% 1/10W

R257 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R258 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R259 1-216-809-11 METAL CHIP 100 5% 1/10W

R260 1-216-809-11 METAL CHIP 100 5% 1/10W

R261 1-216-845-11 METAL CHIP 100K 5% 1/10W

R262 1-216-845-11 METAL CHIP 100K 5% 1/10W

R263 1-218-843-11 METAL CHIP 680 0.5% 1/10W

R264 1-218-831-11 METAL CHIP 220 0.5% 1/10W

R265 1-216-837-11 METAL CHIP 22K 5% 1/10W

R266 1-216-182-00 METAL CHIP 220 5% 1/8W

R267 1-216-134-00 METAL CHIP 2.2 5% 1/8W

R268 1-216-134-00 METAL CHIP 2.2 5% 1/8W


R270 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R271 1-216-844-11 METAL CHIP 82K 5% 1/10W

R272 1-216-134-00 METAL CHIP 2.2 5% 1/8W

R275 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R276 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R277 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R278 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R301 1-216-206-00 METAL CHIP 2.2K 5% 1/8W R302 1-216-837-11 METAL CHIP 22K 5% 1/10W

R303 1-216-837-11 METAL CHIP 22K 5% 1/10W

R304 1-216-849-11 METAL CHIP 220K 5% 1/10W

R305 1-216-849-11 METAL CHIP 220K 5% 1/10W

R306 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R307 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R308 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W

R309 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R310 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R311 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W

R312 1-218-843-11 METAL CHIP 680 0.5% 1/10W

R313 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W

R351 1-216-222-00 METAL CHIP 10K 5% 1/8W

R352 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R353 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R354 1-216-222-00 METAL CHIP 10K 5% 1/8W

R355 1-216-839-11 METAL CHIP 33K 5% 1/10W

R356 1-216-839-11 METAL CHIP 33K 5% 1/10W

R357 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R358 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R359 1-216-809-11 METAL CHIP 100 5% 1/10W

R360 1-216-809-11 METAL CHIP 100 5% 1/10W

R361 1-216-845-11 METAL CHIP 100K 5% 1/10W

R362 1-216-845-11 METAL CHIP 100K 5% 1/10W

R363 1-218-843-11 METAL CHIP 680 0.5% 1/10W

R364 1-218-831-11 METAL CHIP 220 0.5% 1/10W R365 1-216-837-11 METAL CHIP 22K 5% 1/10W

R366 1-216-182-00 METAL CHIP 220 5% 1/8W

R367 1-216-134-00 METAL CHIP 2.2 5% 1/8W

R368 1-216-134-00 METAL CHIP 2.2 5% 1/8W


R370 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R371 1-216-844-11 METAL CHIP 82K 5% 1/10W

R372 1-216-134-00 METAL CHIP 2.2 5% 1/8W R375 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R376 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R377 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R378 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R401 1-216-206-00 METAL CHIP 2.2K 5% 1/8W

R402 1-216-837-11 METAL CHIP 22K 5% 1/10W

R403 1-216-837-11 METAL CHIP 22K 5% 1/10W

R404 1-216-849-11 METAL CHIP 220K 5% 1/10W

R405 1-216-849-11 METAL CHIP 220K 5% 1/10W

R406 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R407 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R408 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W

R409 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R410 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R411 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W

R412 1-218-843-11 METAL CHIP 680 0.5% 1/10W

R413 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W

R451 1-216-222-00 METAL CHIP 10K 5% 1/8W

R452 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R453 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R454 1-216-222-00 METAL CHIP 10K 5% 1/8W

R455 1-216-839-11 METAL CHIP 33K 5% 1/10W

R456 1-216-839-11 METAL CHIP 33K 5% 1/10W

R457 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R458 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R459 1-216-809-11 METAL CHIP 100 5% 1/10W R460 1-216-809-11 METAL CHIP 100 5% 1/10W

R461 1-216-845-11 METAL CHIP 100K 5% 1/10W

R462 1-216-845-11 METAL CHIP 100K 5% 1/10W

R463 1-218-843-11 METAL CHIP 680 0.5% 1/10W

R464 1-218-831-11 METAL CHIP 220 0.5% 1/10W

R465 1-216-837-11 METAL CHIP 22K 5% 1/10W

R466 1-216-182-00 METAL CHIP 220 5% 1/8W

R467 1-216-134-00 METAL CHIP 2.2 5% 1/8W

R468 1-216-134-00 METAL CHIP 2.2 5% 1/8W


R470 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R471 1-216-844-11 METAL CHIP 82K 5% 1/10W

R472 1-216-134-00 METAL CHIP 2.2 5% 1/8W

R475 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R476 1-216-823-11 METAL CHIP 1.5K 5% 1/10W

R477 1-218-875-11 METAL CHIP 15K 0.5% 1/10W

R478 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R801 1-216-198-11 METAL CHIP 1K 5% 1/8W

R802 1-216-206-00 METAL CHIP 2.2K 5% 1/8W

R803 1-216-198-11 METAL CHIP 1K 5% 1/8W

R804 1-216-198-11 METAL CHIP 1K 5% 1/8W

R805 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R806 1-220-397-11 METAL CHIP 4.7M 5% 1/10W

R807 1-216-841-11 METAL CHIP 47K 5% 1/10W

R808 1-216-844-11 METAL CHIP 82K 5% 1/10W

R809 1-216-222-00 METAL CHIP 10K 5% 1/8W R810 1-218-847-11 METAL CHIP 1K 0.5% 1/10W

R811 1-218-847-11 METAL CHIP 1K 0.5% 1/10W

MAIN


21/22


XM-GTX6040

2121

R812 1-216-837-11 METAL CHIP 22K 5% 1/10W

R813 1-216-837-11 METAL CHIP 22K 5% 1/10W

R814 1-216-210-00 METAL CHIP 3.3K 5% 1/8W

R815 1-216-210-00 METAL CHIP 3.3K 5% 1/8W

R816 1-220-397-11 METAL CHIP 4.7M 5% 1/10W

R817 1-220-397-11 METAL CHIP 4.7M 5% 1/10W R818 1-220-397-11 METAL CHIP 4.7M 5% 1/10W

R901 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R902 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R903 1-216-841-11 METAL CHIP 47K 5% 1/10W

R904 1-218-839-11 METAL CHIP 470 0.5% 1/10W

R905 1-218-847-11 METAL CHIP 1K 0.5% 1/10W

R907 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W

R908 1-218-853-11 METAL CHIP 1.8K 0.5% 1/10W

R909 1-218-843-11 METAL CHIP 680 0.5% 1/10W

R910 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W

R911 1-218-880-11 METAL CHIP 24K 0.5% 1/10W

R912 1-216-845-11 METAL CHIP 100K 5% 1/10W

R914 1-216-206-00 METAL CHIP 2.2K 5% 1/8W

R915 1-216-814-11 METAL CHIP 270 5% 1/10W

R916 1-218-847-11 METAL CHIP 1K 0.5% 1/10W

R917 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R918 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R919 1-216-222-00 METAL CHIP 10K 5% 1/8W

R920 1-216-190-00 METAL CHIP 470 5% 1/8W

R921 1-216-190-00 METAL CHIP 470 5% 1/8W

R922 1-218-847-11 METAL CHIP 1K 0.5% 1/10W

R923 1-218-847-11 METAL CHIP 1K 0.5% 1/10W

R924 1-218-847-11 METAL CHIP 1K 0.5% 1/10W

R925 1-218-847-11 METAL CHIP 1K 0.5% 1/10W

R926 1-216-158-00 METAL CHIP 22 5% 1/8W

R927 1-216-158-00 METAL CHIP 22 5% 1/8W R928 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R929 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R930 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R931 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R932 1-216-150-11 METAL CHIP 10 5% 1/8W

R933 1-216-150-11 METAL CHIP 10 5% 1/8W

R934 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R935 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R936 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R937 1-218-847-11 METAL CHIP 1K 0.5% 1/10W

R938 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R939 1-216-839-11 METAL CHIP 33K 5% 1/10W

R940 1-216-206-00 METAL CHIP 2.2K 5% 1/8W

R941 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R942 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R943 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R944 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R945 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

R946 1-218-871-11 METAL CHIP 10K 0.5% 1/10W

< SWITCH >

S801 1-554-222-00 SWITCH, SLIDE (HPF(80Hz) (FRONT))

S802 1-554-222-00 SWITCH, SLIDE (LPF(80Hz) (REAR))

< TRANSFORMER >

T901 1-443-277-22 TRANSFORMER, DC-DC CONVERTER

< THERMISTOR >

TH901 1-801-597-11 THERMISTOR



< VARIABLE RESISTOR >

VR801 1-227-768-11 RES, VAR, CARBON 10KX2 (LEVEL (FRONT))

VR802 1-227-768-11 RES, VAR, CARBON 10KX2 (LEVEL (REAR))

*************************************************************

ACCESSORIES

************

4-151-109-11 MANUAL INSTRUCTION (ENGLISH,FRENCH,

SPANISH)

*************************************************************

PARTS FOR INSTALLATION AND CONNECTIONS

**************************************

101 X-2108-372-1 SCREW SUB ASSY (MOUNTING SCREW) (4pcs)

102 1-823-952-11 CORD (WITH CONNECTOR)

(HIGH LEVEL INPUT) (0.2m)

103 2-695-957-01 COVER (POWER)

101 102 103

( 4) 0.2 m 5 15 mm

MAIN


22/22

XM-GTX6040

REVISION HISTORY

Checking the version allows you to jump to the revised page.

Also, clicking the version at the top of the revised page allows you to jump to the next revised page.

Ver. Date Description of Revision

1.0 2009.06 New

Xm Gtx6040 Sony Schematics

Documents