XiLog+ sensor Installation and operating instructions GRUNDFOS INSTRUCTIONS
XiLog+ sensorInstallation and operating instructions
GRUNDFOS INSTRUCTIONS
2
En
glis
h (
GB
)
3
English (GB) Installation and operating instructions
Original installation and operating instructions
CONTENTSPage
1. Symbols used in this document
2. IntroductionThe XiLog+ sensor is a key component in the Grundfos Demand Driven Distribution system.
The sensor logs the water pressure at the consumer’s property and sends a report to the CU 354 controller controlling the booster pumps that deliver the water.
The sensor has a built-in GSM 2G antenna and must be installed close to the main pipe where there is access to a GSM network. We recommend that you run a signal strength test before installing the sensor, see section 6. Signal test on page 10.
For further information about the Primayer XiLog+, see its manual.
3. Receiving the product
3.1 Scope of delivery
4. Installing the productCarry out the installation in this order:
1. Install the SIM card.
2. Install the sensor.
3. Set up the sensor.
4. Set up the CU 354.
1. Symbols used in this document 3
2. Introduction 3
3. Receiving the product 33.1 Scope of delivery 3
4. Installing the product 34.1 Installing the SIM card 44.2 Installing the sensor 44.3 Connecting the sensor 6
5. Setting up the sensor 7
6. Signal test 10
7. Setting the CU 354 117.1 How to use the CU 354 11
8. Battery replacement 11
9. Disposal 11
Read this document before installing the product. Installation and operation must comply with local regulations and accepted codes of good practice.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Warning
If these safety instructions are not observed, it may result in personal injury.
Tips and advice that make the work easier.
Component Quantity
Primayer XiLog+ sensor 1
Metal bracket 1
Screws and rawlplugs 2/2
Quick-fitting coupling, DN 5 1/4" BSP parallel thread, for main pipe
1
Flexible hose 1
Installation and operating instructions
1
USB stick with software 1
En
glish
(GB
)
4
4.1 Installing the SIM card
Procedure
1. Insert the SIM card into a mobile phone.
2. Remove the PIN code from the SIM card.
3. Remove the small metal plate on the bottom of the XiLog+ sensor.
Fig. 1 Removing the metal plate
4. Press the yellow button to release the holder.
5. Remove the SIM card holder with a screwdriver.
Fig. 2 Removing the SIM card holder
6. Insert the SIM card into the holder.
Fig. 3 SIM card in the holder
7. Insert the holder with the SIM card into the sensor.
8. Fit the metal plate again and tighten the screws.
4.2 Installing the sensor
1. Find a suitable location for the sensor, typically in a pit or close to the main pipe.
2. Check the signal strength at the site with your mobile phone.
3. Mount the metal bracket.
Fig. 4 Mounting the metal bracket
A SIM card is required for each sensor in the system.
TM
05
91
78
34
13
TM
05
91
79
34
13
TM
05
91
80
34
13
TM
05
92
75
36
13
The flex hose between the main pipe and the sensor will not have any flow, and is therefore susceptible to freezing.
The sensor will be damaged if exposed to freezing water.
En
glis
h (
GB
)
5
4. Slide the sensor onto the bracket.
Fig. 5 Sliding the sensor onto the bracket
5. Connect the flexible hose to the sensor.
Fig. 6 Connecting the flexible hose to the sensor
6. Install the quick-fitting coupling (see fig. 7) on the top of the main pipe.
Fig. 7 DN 5 1/4" BSP parallel thread quick-fitting coupling
7. The flexible hose will be connected to the quick-fitting coupling after you have performed an Auto zero using the Fast Track program.
Fig. 8 Connecting the flexible hose to the quick-fitting coupling.
TM
05
92
76
36
13
TM
05
91
87
37
13
TM
05
91
88
34
13
TM
05
91
88
34
13
En
glish
(GB
)
6
4.3 Connecting the sensor
1. Check that the XiLog + Fast Track program is installed on your PC. If not, use the USB stick to install the software on your PC.
2. Establish a connection between the sensor and your PC using the data cable (Grundfos product number 98486261, not supplied with the product).
3. Remove the protective cover from the data cable.
Fig. 9 Protective cover and data cable
4. Connect the data cable.
Fig. 10 Connecting the data cable
5. Connect the USB plug of the data cable to your PC.
TM
05
94
40
37
13
TM
05
94
40
37
13
En
glis
h (
GB
)
7
5. Setting up the sensor
1. Start the XiLog+ Fast Track program on your PC, and make sure the sensor is connected. Your screen should look like this:
Fig. 11 Main menu
Before you begin, load the setting currently set in the sensor.
2. Click [Load Config].
Fig. 12 Load config.
The sensor is now ready to receive new input.
When you start this procedure, the sensor leaves freight mode and becomes active.
If you need to change the GSM frequency band, use the GPRSconfig.exe file on the USB stick.
The Fast Track program changes the PC’s time to match the sensor’s when connected. Ensure that the time on your computer and the CU 354 controller are synchronised.
TM
05
93
74
13
15
TM
05
93
74
13
15
En
glish
(GB
)
8
3. Adjust the following parameters:
• Phone number
• Choose SMS transmission
• Host number for the CU 354
• Units for "bar"
• Interval of 15 minutes.
See explanation below.
* The low threshold is to be set in the CU 354, see the SW IO.
Click [Start]. Note the progress bar at the top.
Fig. 13 The screen after setup.
ParameterDefault setting
Grundfos setting
Site name -Site name/street name
Phone number -Number to SIM card in the XiLog+ sensor
Transmit time 00:00 00:00
Auto GSM clock correction
Unchecked Checked
Host number -
Number for the CIU 250 which is connected to the CU 354
Use XMS host Unchecked Unchecked
Alarm number - -
FTP transmission Unchecked Unchecked
Units Bar Bar
Interval 15 minutes 15 minutes
Threshold alarms enabled
CheckedChecked. To be set in the CU 354.
Low threshold* 0.0 bar 0.0 bar
High threshold 3.5 bar 20.0 bar
Deadband 0.5 bar 0.5 bar
Debounce delay 15 minutes 15 minutes
Do not change the units to "meter", as the CU 354 operates in "bar".
If you use decimals for setting the low threshold, your computer settings need to meet the requirements.
Ensure decimals are changed to "." in your region and language settings on your pc.
For windows pc, follow this path: Control panel/Region and Language/Formats - Additional settings...
TM
06
39
67
13
15
En
glis
h (
GB
)
9
Fig. 14 Setting up the sensor
When the sensor has been set up, a live data feed will be available.
If you install the sensor in high altitude areas, you have to use the [Auto Zero] function to zero the sensor. The pressure will affect the sensor as it measures absolute pressure.
The sensor must be removed from the system pressure before using the auto zero function.
Fig. 15 Live data feed from the sensor
4. Click [Finish] to terminate the connection with the sensor and unplug the sensor.Do not forget to fit the protective cover for the data cable.
Fig. 16 Protective cover and data cable
TM
05
93
78
13
15
TM
05
93
79
13
15
TM
05
94
40
37
13
En
glish
(GB
)
10
6. Signal testTo run a signal strength test, start the XiLog+ Fast Track program on your PC, and connect the sensor via the data cable.
1. Click [Signal Strength] in the main menu to access the signal strength test.
Fig. 17 Main menu
This screen appears.
Fig. 18 Signal strength test start page
2. To start the test, click [All Networks] and select "Run Test".
3. To test the signal from the SIM card provider, click [Current Signal] and select [Run Test].Do not move the sensor while the test is being performed. Wait for the test results to appear on the screen.
Fig. 19 Signal strength test results
For proper GSM connection, the signal strength must be above 21 %.
4. Click [X] to close the test.
TM
06
39
67
13
15
TM
05
93
76
13
15
Perform the test as realistic as possible, for example under the manhole cover.
TM
05
93
77
13
15
En
glis
h (
GB
)
11
7. Setting the CU 354Set the sensors from the CU 354 or use the PC tool.
For further information, see the installation and operating instructions for the CU 354.
7.1 How to use the CU 354
1. Go to 4.3.25, "Remote sensors".
Fig. 20 Remote sensors
2. Enter the phone number for the CU 354 DDD controller and remember the country code; use "+" instead of "00".
3. Set the number of sensors installed, in this example, there are five sensors.
4. Scroll down to the first sensor, and press [OK].
Fig. 21 Remote sensor 1
5. Select sensor "Enabled".
6. Select the sensor type Primayer XiLog+.
7. Enter the name of the sensor. We recommend that you use the same name that was given via XiLog+ Fast Track.
8. Enter the phone number of the sensor as "+" followed by the country code and the local number.
9. Set the setpoint at the sensor’s position. This will be the minimum pressure setpoint that the CU 354 controller will try to maintain.
10. Enable the sensor alarms and set a minimum pressure. This allows the sensor to send a warning message if the pressure becomes too low.
11. Scroll down to "Press [OK] to send configuration", and press [OK].
12. Latest response indicates when the latest data were received. This field will be empty until the first data are received. This may take up to 24 hours.
13. Repeat this process with the number of installed sensors. The CU 354 has now been set up to communicate with all remote sensors.
8. Battery replacementSee the Primayer XiLog+ system user manual.
9. DisposalThis product or parts of it must be disposed of in an environmentally sound way:
1. Use the public or private waste collection service.
2. If this is not possible, contact the nearest Grundfos company or service workshop.
The crossed-out wheelie bin symbol on a product means that it must be disposed of separately from household waste. When a product marked with this symbol reaches its end of life, take it to a collection point designated by the local
waste disposal authorities. The separate collection and recycling of such products will help protect the environment and human health.
TM
05
87
10
45
18
TM
05
87
11 4
51
8
If the sensor is mounted above the pipe, please take notice of this when setting the setpoint.
12
13
Gru
nd
fos co
mp
anies
ArgentinaBombas GRUNDFOS de Argentina S.A.Ruta Panamericana km. 37.500 Centro Industrial Garin1619 Garín Pcia. de B.A.Phone: +54-3327 414 444Telefax: +54-3327 45 3190
AustraliaGRUNDFOS Pumps Pty. Ltd. P.O. Box 2040 Regency Park South Australia 5942 Phone: +61-8-8461-4611 Telefax: +61-8-8340 0155
AustriaGRUNDFOS Pumpen Vertrieb Ges.m.b.H.Grundfosstraße 2 A-5082 Grödig/Salzburg Tel.: +43-6246-883-0 Telefax: +43-6246-883-30
BelgiumN.V. GRUNDFOS Bellux S.A. Boomsesteenweg 81-83 B-2630 Aartselaar Tél.: +32-3-870 7300 Télécopie: +32-3-870 7301
BelarusПредставительство ГРУНДФОС в Минске220125, Минскул. Шафарнянская, 11, оф. 56, БЦ «Порт»Тел.: +7 (375 17) 286 39 72/73Факс: +7 (375 17) 286 39 71E-mail: [email protected]
Bosnia and HerzegovinaGRUNDFOS SarajevoZmaja od Bosne 7-7A,BH-71000 SarajevoPhone: +387 33 592 480Telefax: +387 33 590 465www.ba.grundfos.come-mail: [email protected]
BrazilBOMBAS GRUNDFOS DO BRASILAv. Humberto de Alencar Castelo Branco, 630CEP 09850 - 300São Bernardo do Campo - SPPhone: +55-11 4393 5533Telefax: +55-11 4343 5015
BulgariaGrundfos Bulgaria EOODSlatina DistrictIztochna Tangenta street no. 100BG - 1592 SofiaTel. +359 2 49 22 200Fax. +359 2 49 22 201email: [email protected]
CanadaGRUNDFOS Canada Inc. 2941 Brighton Road Oakville, Ontario L6H 6C9 Phone: +1-905 829 9533 Telefax: +1-905 829 9512
ChinaGRUNDFOS Pumps (Shanghai) Co. Ltd.10F The Hub, No. 33 Suhong RoadMinhang DistrictShanghai 201106PRCPhone: +86 21 612 252 22Telefax: +86 21 612 253 33
COLOMBIAGRUNDFOS Colombia S.A.S.Km 1.5 vía Siberia-Cota Conj. Potrero Chico,Parque Empresarial Arcos de Cota Bod. 1A.Cota, CundinamarcaPhone: +57(1)-2913444Telefax: +57(1)-8764586
CroatiaGRUNDFOS CROATIA d.o.o.Buzinski prilaz 38, BuzinHR-10010 ZagrebPhone: +385 1 6595 400 Telefax: +385 1 6595 499www.hr.grundfos.com
GRUNDFOS Sales Czechia and Slovakia s.r.o.Čajkovského 21779 00 OlomoucPhone: +420-585-716 111
DenmarkGRUNDFOS DK A/S Martin Bachs Vej 3 DK-8850 Bjerringbro Tlf.: +45-87 50 50 50 Telefax: +45-87 50 51 51 E-mail: [email protected]/DK
EstoniaGRUNDFOS Pumps Eesti OÜPeterburi tee 92G11415 TallinnTel: + 372 606 1690Fax: + 372 606 1691
FinlandOY GRUNDFOS Pumput AB Trukkikuja 1 FI-01360 Vantaa Phone: +358-(0) 207 889 500
FrancePompes GRUNDFOS Distribution S.A. Parc d’Activités de Chesnes 57, rue de Malacombe F-38290 St. Quentin Fallavier (Lyon) Tél.: +33-4 74 82 15 15 Télécopie: +33-4 74 94 10 51
GermanyGRUNDFOS GMBHSchlüterstr. 3340699 ErkrathTel.: +49-(0) 211 929 69-0 Telefax: +49-(0) 211 929 69-3799e-mail: [email protected] in Deutschland:e-mail: [email protected]
GreeceGRUNDFOS Hellas A.E.B.E. 20th km. Athinon-Markopoulou Av. P.O. Box 71 GR-19002 Peania Phone: +0030-210-66 83 400 Telefax: +0030-210-66 46 273
Hong KongGRUNDFOS Pumps (Hong Kong) Ltd. Unit 1, Ground floor Siu Wai Industrial Centre 29-33 Wing Hong Street & 68 King Lam Street, Cheung Sha Wan Kowloon Phone: +852-27861706 / 27861741 Telefax: +852-27858664
HungaryGRUNDFOS Hungária Kft.Tópark u. 8H-2045 Törökbálint, Phone: +36-23 511 110Telefax: +36-23 511 111
IndiaGRUNDFOS Pumps India Private Limited118 Old Mahabalipuram RoadThoraipakkamChennai 600 096Phone: +91-44 2496 6800
IndonesiaPT. GRUNDFOS POMPAGraha Intirub Lt. 2 & 3Jln. Cililitan Besar No.454. Makasar, Jakarta TimurID-Jakarta 13650Phone: +62 21-469-51900Telefax: +62 21-460 6910 / 460 6901
IrelandGRUNDFOS (Ireland) Ltd. Unit A, Merrywell Business ParkBallymount Road LowerDublin 12 Phone: +353-1-4089 800 Telefax: +353-1-4089 830
ItalyGRUNDFOS Pompe Italia S.r.l. Via Gran Sasso 4I-20060 Truccazzano (Milano)Tel.: +39-02-95838112 Telefax: +39-02-95309290 / 95838461
JapanGRUNDFOS Pumps K.K.1-2-3, Shin-Miyakoda, Kita-ku, Hamamatsu431-2103 JapanPhone: +81 53 428 4760Telefax: +81 53 428 5005
KoreaGRUNDFOS Pumps Korea Ltd.6th Floor, Aju Building 679-5Yeoksam-dong, Kangnam-ku, 135-916Seoul, KoreaPhone: +82-2-5317 600Telefax: +82-2-5633 725
LatviaSIA GRUNDFOS Pumps Latvia Deglava biznesa centrsAugusta Deglava ielā 60, LV-1035, Rīga,Tālr.: + 371 714 9640, 7 149 641Fakss: + 371 914 9646
LithuaniaGRUNDFOS Pumps UABSmolensko g. 6LT-03201 VilniusTel: + 370 52 395 430Fax: + 370 52 395 431
Gru
nd
fos
com
pan
ies
MalaysiaGRUNDFOS Pumps Sdn. Bhd.7 Jalan Peguam U1/25Glenmarie Industrial Park40150 Shah AlamSelangor Phone: +60-3-5569 2922Telefax: +60-3-5569 2866
MexicoBombas GRUNDFOS de México S.A. de C.V. Boulevard TLC No. 15Parque Industrial Stiva AeropuertoApodaca, N.L. 66600Phone: +52-81-8144 4000 Telefax: +52-81-8144 4010
NetherlandsGRUNDFOS NetherlandsVeluwezoom 351326 AE AlmerePostbus 220151302 CA ALMERE Tel.: +31-88-478 6336 Telefax: +31-88-478 6332E-mail: [email protected]
New ZealandGRUNDFOS Pumps NZ Ltd.17 Beatrice Tinsley CrescentNorth Harbour Industrial EstateAlbany, AucklandPhone: +64-9-415 3240Telefax: +64-9-415 3250
NorwayGRUNDFOS Pumper A/S Strømsveien 344 Postboks 235, Leirdal N-1011 Oslo Tlf.: +47-22 90 47 00 Telefax: +47-22 32 21 50
PolandGRUNDFOS Pompy Sp. z o.o.ul. Klonowa 23Baranowo k. PoznaniaPL-62-081 PrzeźmierowoTel: (+48-61) 650 13 00Fax: (+48-61) 650 13 50
PortugalBombas GRUNDFOS Portugal, S.A. Rua Calvet de Magalhães, 241Apartado 1079P-2770-153 Paço de ArcosTel.: +351-21-440 76 00Telefax: +351-21-440 76 90
RomaniaGRUNDFOS Pompe România SRLBd. Biruintei, nr 103 Pantelimon county IlfovPhone: +40 21 200 4100Telefax: +40 21 200 4101E-mail: [email protected]
RussiaООО Грундфос Россияул. Школьная, 39-41Москва, RU-109544, Russia Тел. (+7) 495 564-88-00 (495) 737-30-00Факс (+7) 495 564 8811E-mail [email protected]
Serbia Grundfos Srbija d.o.o.Omladinskih brigada 90b11070 Novi Beograd Phone: +381 11 2258 740Telefax: +381 11 2281 769www.rs.grundfos.com
SingaporeGRUNDFOS (Singapore) Pte. Ltd.25 Jalan Tukang Singapore 619264 Phone: +65-6681 9688 Telefax: +65-6681 9689
SlovakiaGRUNDFOS s.r.o.Prievozská 4D 821 09 BRATISLAVA Phona: +421 2 5020 1426sk.grundfos.com
SloveniaGRUNDFOS LJUBLJANA, d.o.o.Leskoškova 9e, 1122 LjubljanaPhone: +386 (0) 1 568 06 10Telefax: +386 (0)1 568 06 19E-mail: [email protected]
South AfricaGRUNDFOS (PTY) LTDCorner Mountjoy and George Allen RoadsWilbart Ext. 2Bedfordview 2008Phone: (+27) 11 579 4800Fax: (+27) 11 455 6066E-mail: [email protected]
SpainBombas GRUNDFOS España S.A. Camino de la Fuentecilla, s/n E-28110 Algete (Madrid) Tel.: +34-91-848 8800 Telefax: +34-91-628 0465
SwedenGRUNDFOS AB Box 333 (Lunnagårdsgatan 6) 431 24 Mölndal Tel.: +46 31 332 23 000Telefax: +46 31 331 94 60
SwitzerlandGRUNDFOS Pumpen AG Bruggacherstrasse 10 CH-8117 Fällanden/ZH Tel.: +41-44-806 8111 Telefax: +41-44-806 8115
TaiwanGRUNDFOS Pumps (Taiwan) Ltd. 7 Floor, 219 Min-Chuan Road Taichung, Taiwan, R.O.C. Phone: +886-4-2305 0868Telefax: +886-4-2305 0878
ThailandGRUNDFOS (Thailand) Ltd. 92 Chaloem Phrakiat Rama 9 Road,Dokmai, Pravej, Bangkok 10250Phone: +66-2-725 8999Telefax: +66-2-725 8998
TurkeyGRUNDFOS POMPA San. ve Tic. Ltd. Sti.Gebze Organize Sanayi Bölgesi Ihsan dede Caddesi,2. yol 200. Sokak No. 20441490 Gebze/ KocaeliPhone: +90 - 262-679 7979Telefax: +90 - 262-679 7905E-mail: [email protected]
UkraineБізнес Центр ЄвропаСтоличне шосе, 103м. Київ, 03131, Україна Телефон: (+38 044) 237 04 00 Факс.: (+38 044) 237 04 01E-mail: [email protected]
United Arab EmiratesGRUNDFOS Gulf DistributionP.O. Box 16768Jebel Ali Free ZoneDubaiPhone: +971 4 8815 166Telefax: +971 4 8815 136
United KingdomGRUNDFOS Pumps Ltd. Grovebury Road Leighton Buzzard/Beds. LU7 4TL Phone: +44-1525-850000 Telefax: +44-1525-850011
U.S.A.GRUNDFOS Pumps Corporation 9300 Loiret Blvd.Lenexa, Kansas 66219Phone: +1-913-227-3400 Telefax: +1-913-227-3500
UzbekistanGrundfos Tashkent, Uzbekistan The Rep-resentative Office of Grundfos Kazakhstan in Uzbekistan38a, Oybek street, TashkentТелефон: (+998) 71 150 3290 / 71 150 3291Факс: (+998) 71 150 3292
Addresses Revised 14.03.2018
www.grundfos.com
98538516 1218
ECM: 1251155 Tra
dem
arks
dis
pla
yed
in th
is m
ate
rial,
incl
udin
g bu
t not
lim
ited
to G
rund
fos,
the
Gru
ndfo
s lo
go a
nd “
be
thin
k in
nova
te”
are
reg
iste
red
trad
emar
ks o
wne
d by
Th
e G
rund
fos
Gro
up. A
ll rig
hts
res
erve
d.©
201
8 G
rund
fos
Hol
ding
A/S
, all
right
s re
serv
ed.