XG100 Flash Utility Guide v3.0

8/3/2019 XG100 Flash Utility Guide v3.0

1/12

Janam XG100 Flash Utility Guide

Reference Guide

Version 3.0

This document will be treated as Confidential Information under the terms stated in theNon-Disclosure Agreement. No part of it may be circulated, quoted or reproduced for

distribution without prior written approval from Janam Technologies LLC .


2/12


This document describes how to download .NB0 files onto Win CE 6 (Craft) device

using USB cable.

!

1. Windows XP PC2. USB Mobile cradle or Single Cradle with a USB cable (A to B plug)3. 9V DC/2A Power supply.4. Files (*.NB0)

"#

1. Hardware setup is shown asFigure 1.

Figure 1: USB Cable Connection

Software setup: Installing USB Remote NDIS Device Driver on

Windows XP PC

For USB Image download, the RNDIS driver for the Windows XP PC has to be

installed first. Skip this procedure if the USB Remote NDIS Device Driver

installation has been done.

Instruction:

a) Setup a USB Connection asFigure 1.b) Press & release + buttons and immediately press & hold

+ buttons until the device enters Download Mode. The

device will display the splash screen for Download Mode asFigure 2.

XG100

(WinCE6)

USB Mobile/

Single Cradle

PC(WinXP)

DC Power

Supply 9V

USB Cable

DC Input

USB plug to

USB port


3/12


Figure 2: Splash screen for Download Mode

c) After few seconds, Windows XP shows a notification box to indicate that a newhardware device has been found. Refer toFigure 3.

Figure 3: New Hardware Found

d) On the next dialog box select Install from a list or specific location.


4/12


Figure 4: Select Install from a list or specific location (Advanced)

e) On the next dialog box key in the path where you would find the driver files forthe RNDIS KITL driver, under the folder of [ActiveSync_USB_Host_Driver].

Click button to proceed.

Figure 5: Browse for ActiveSync_USB_Host_Driver folder


5/12


f) Hardware Installation warning dialog box prompts. Click on button to continue.

Figure 6: Continue installation by clicking on button

g) Driver installation starts.


6/12


Figure 7: Installation in progress

h) Click on button when the driver installation is completed.

Figure 8: Installation completed

i) The setup is complete.


7/12


Procedure for Image Flashing

1. Setup a USB Connection asFigure 1.2. Press & release + buttons and immediately press & hold

+ buttons until the device enters Download Mode. Thedevice will display the splash screen for Download Mode asFigure 9.

Figure 9: Splash screen for Download Mode


8/12


3. Copy XGFlash.exe into the PC Desktop. Double click on XGFlash.exe tolaunch the XG Series Flashing Program as below. Refer toFigure 10.

Figure 10: XG Series Flashing Program


9/12


4. Switch to XG Series Flashing Program, click on toolbar. Browseto select the software image (ALLIMAGE.nb0) to be flashed into the device.Click on button. Refer toFigure 11.

Figure 11: Open ALLIMAGE.nb0 image file


10/12


5. Click on the toolbar to start downloading the image. Refer toFigure 12.

Figure 12: Download ALLIMAGE.nb0 file


11/12


6. Image downloading message is shown in XG Series Flashing Program. ACKis increasing from 0 to the full file size of the nb0 file, in this case is 61,734,912bytes. Message of Transfer of ALLIMAGE.nb0 has successfully completed is

also shown on the message box. Refer toFigure 13.

Figure 13: USB image download completed


12/12


7. Leave the device untouched until the image update process is completed. Thedevice will auto-cold boot with calibration screen appears asFigure 14.

Figure 14: Calibration screen appears after image flashing completed

8. Now it is safe to remove the connection from the PC.

XG100 Flash Utility Guide v3.0

Documents