XDS560v2 Installation Guide - dspblog.co.kr · 1 XDS560V2 Installation Guide ... This document is a system overview for the Texas Instruments ... configuration or double on an existing

XDS560v2 Installation Guide

1

XDS560V2XDS560V2XDS560V2XDS560V2InstallationInstallationInstallationInstallationGuideGuideGuideGuide

Wintech Digital System Co., Ltd

http://www.wintechdigital.com

http://www.wintechdigital.com


2

IMPORTANTIMPORTANTIMPORTANTIMPORTANT INFORMATIONINFORMATIONINFORMATIONINFORMATIONAboutAboutAboutAbout ThisThisThisThis ManualManualManualManual

This Installation Guide is for the Wintech Digital XDS560v2 JTAGEmulator product.

The Wintech Digital XDS560v2 JTAG Emulator is a module to beattached to a PC for hardware engineers and software programmers todevelop DSP applications.

The text paragraphs in this Guide are very important for properdevice functioning and for preventing any possible damages on the WintechDigital XDS560v2 JTAG Emulator device and project target board. Theseparagraphs are shaded as in the following example. Please carefully readeach of the shaded text.

ThisThisThisThis isisisis anananan exampleexampleexampleexample ofofofof aaaa veryveryveryvery importantimportantimportantimportant texttexttexttext paragraph.paragraph.paragraph.paragraph.


3

TABLETABLETABLETABLE OFOFOFOFCONTENTSCONTENTSCONTENTSCONTENTSINTRODUCTIONINTRODUCTIONINTRODUCTIONINTRODUCTION................................................................................................................................................................................................................................................................................................................................................................ 4444

OVERVIEW......................................................................................................................... 4FEATURES.......................................................................................................................... 5THE XDS560V2 JTAG EMULATOR KIT CONTAINS............................................................6INSTALLATION REQUIREMENTS......................................................................................... 6SUPPORTS OPERATING SYSTEMS....................................................................................... 6

QUICKQUICKQUICKQUICK INSTALLINSTALLINSTALLINSTALL........................................................................................................................................................................................................................................................................................................................................................................7777QUICK INSTALL PROCEDURES............................................................................................7

DETAILDETAILDETAILDETAIL INSTALLINSTALLINSTALLINSTALL................................................................................................................................................................................................................................................................................................................................................................8888DETAIL INSTALL PROCEDURES.......................................................................................... 8

HARDWAREHARDWAREHARDWAREHARDWARE SELF-TESTSELF-TESTSELF-TESTSELF-TEST.................................................................................................................................................................................................................................................................................................... 10101010HARDWARE SELF-TEST PROCEDURES.............................................................................10


4

IntroductionIntroductionIntroductionIntroductionOverviewOverviewOverviewOverview

This document is a system overview for the Texas Instruments (TI)XDS560v2 Debug and Test Controller (DTC). XDS560v2 DTC is anemulator that provides an interface between IEEE1149.1/1149.7 compliantJTAG signals and a host-side debug system.

Figure 1� ScopeThe scope of this document is limited to providing system-level overviewfor the XDS560v2 product. In general, attempt is made to provide briefinformation about relevant peripherals or specification for clarity. Readersshould refer to related reference material for detailed information.� Intended audienceThis document is intended for the following audience:Hardware engineers developing XDS560v2 reference platforms;


5

Software engineers developing software for XDS560v2 DTC;Test engineers validating the product;Early adopter third-party developers developing XDS560v2 derivatives;Product & Program Managers.

FeaturesThis product has the following hardware features:� TMS320DM6441 (405/513 MHz)� 256 MBytes of DDR2 SDRAM� 64 MBytes of NAND flash� USB 2.0� 5V input power with LED� 16-bit EMIF DM6441 interface to FPGA� 16-bit Video interface from FPGA to DM6441� Cyclone III FPGA� 6 Status LEDs(Table-1)� Boot-mode jumper� Maximum TCLK:27Mhz� Supports Texas Instruments Digital Signal Processors and Microcontrollers with

JTAGJTAGJTAGJTAG interface:• C64x+• C28xxx• C5000• C6000• DaVinci• ARM (Cortex-M3/Cortex-M4/ARM9/Cortex-A8/Cortex-A9/CortexA-15)• OMAP3• OMAP4• OMAP5• OMAPL13x

This product will support following functions:� IEEE 1149.1 debug� IEEE 1149.7 debug� Boot mode control on EMU pins� Supports Embedded Trace Buffer (ETB) on selected TI devices

This version of the product will not support the following functions:� Processor Trace


6


7

NameNameNameName ColorColorColorColor MeaningMeaningMeaningMeaningPower GREEN Emulator Power IndicatorBusy GREEN ON =CCS Connected

OFF= CCS DisconnectedStart YELLOW ON = FPGA Programmed

OFF = FPGA Not ProgrammedReady RED ON = DTC Ready

OFF = DTC Not ReadyReserved GREEN Reserved

Host YELLOW DTC to Host ActivityTrace RED Target to DTC Trace Activity

Table 1 Meaning of Status LED's

The XDS560v2 JTAG Emulator kit contains· XDS560v2 JTAG Emulator and target cable· USB interface cable· 5-Volt DC power supply· AC power cord· The XDS560v2 driver disk· XDS560v2 Installation Guide (this document)

Installation Requirements· Code Composer Studio IDE 4.2 or greater· An available USB port (USB2.0 is recommended)· 1GHz or higher Pentium Ô -compatible CPU· Local CD-ROM drive


8

Supports Operating Systems

� Microsoft Windows™ 2000 (SP3 or later)� Microsoft Windows™ XP (Home and Professional)� Microsoft Windows™ 2003 Server� Microsoft Windows™ Vista� Microsoft Windows™ 7 (32bit and 64bit)

Quick InstallQuick Install Procedures

This Guide describes the steps to install the XDS560v2 JTAG Emulator inthe following order:

1.1.1.1. Make sure Code Composer Studio IDE 4.2 or greater is installed onthe PC;

2.2.2.2. Install the XDS560v2 JTAG Emulator software;3.3.3.3. Install the XDS560v2 JTAG Emulator hardware;4.4.4.4. Install the XDS560v2 JTAG device driver(USB Mode);5.5.5.5. Run CCS, configure CCS and debug the target.


9

Detail InstallDetail Install Procedures

This Guide describes the steps to install the XDS560v2 JTAG Emulator inthe following order:

1. Install Code Composer Studio IDE 4.2;2. Run Setup_XDS560v2.exe on the user disk to install the XDS560v2

JTAG emulator software;3. Connect the XDS560v2 target cable to the emulator;4. Connect the USB cable;5. Power on the XDS560v2 emulator and wait for about 25 seconds. The

“Start” LED and “Ready” LED will light on;6. If the USB cable is properly connected, the system will prompt to find

a new hardware;7. Please install the device driver. Please select the user disk as the

source of driver;8. Run CCS. Click “View->Target Configurations” on the main menu to

activate the “Target Configurations” window;9. Click “Target->New Target Configurations” to create a new

configuration or double on an existing configuration to modify it;10. Select “WintechDigital XDS560V2 STM USB Emulator”( Figure 2),

depending on your connection type;11. Select a target to match your target board (Figure 2);


10

Figure 2

12. Click “Save” to save the configuration;13. Click “Target->Launch TI Debugger” on the main menu to activate

the debug window;14. Click “Target->Connect Target” to connect the target.

Hardware Self-TestHardware Self-Test Procedures

This Guide describes the steps to run the XDS560v2 JTAG Emulator self-test in the following order:

1. Make sure the emulator is connected from host to target;2. Run xds560v2probe.exe located in CCSv4\common\uscif\ or launch it

from shortcut “Wintech Digital” on Destop;3. Choose one of test options and click “start” button to begin self-test;


11

�� ItItItIt isisisis veryveryveryvery importantimportantimportantimportant totototo properlyproperlyproperlyproperly orientorientorientorient thethethethe connectorconnectorconnectorconnector onononon thethethethe DSPDSPDSPDSPtargettargettargettarget systemsystemsystemsystem sosososo thatthatthatthat PinPinPinPin 1111 onononon thethethethe cablecablecablecable matchesmatchesmatchesmatches PinPinPinPin 1111 onononon thethethethe DSPDSPDSPDSPtargettargettargettarget system.system.system.system. ConnectingConnectingConnectingConnecting thethethethe cablecablecablecable incorrectlyincorrectlyincorrectlyincorrectly maymaymaymay causecausecausecause damagesdamagesdamagesdamagesonononon youryouryouryour DSPDSPDSPDSP targettargettargettarget systemsystemsystemsystem orororor thethethethe XDS560v2XDS560v2XDS560v2XDS560v2 JTAGJTAGJTAGJTAG Emulator.Emulator.Emulator.Emulator.

XDS560v2 Installation Guide - dspblog.co.kr · 1 XDS560V2 Installation Guide ... This document is a system overview for the Texas Instruments ... configuration or double on an existing

Documents