WORKSHOP STOOL Model 875.618281 Black Model 875.528280 Blue Model 875.528290 Silver Model 875.528300 Green Model 875.528310 Red Model 875.528320 Yellow One-Year Full Warranty For one year from the date of purchase, if this Craftsman Workshop Stool fails due to defect in materials or workmanship, return it to any Sears store or other Craftsman outlet in the United States for free repair or re- placement. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state. Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179 SAFETY INSTRUCTIONS: WEAR SAFETY GLASSES when assem- bling this product. BE CAREFUL of possible sharp edges. DO NOT stand on this product. You may fall which may cause personal injury. PARTS See illustration on back of page. NOTE: The stool seat and backrest are pre- assembled prior to shipment. ASSEMBLY and OPERATION INSTRUCTIONS For assembly hex key (13) and a mini wrench (14) are supplied. 1. Remove all parts from shipping carton. Remove all packaging material from parts. Check parts against parts list before beginning assembly. If any parts are missing, call 1-800-290-9054. 2. Insert upper end of each backrest support bar (3) into backrest (1) so that one of the two spring locks snaps into place. Be sure to snap each support bar into backrest at same height. 3. Loosen lock knobs on underside of seat (2) enough so that you can insert the lower end of each support bar into the seat bracket. Insert support at least 4 inches to ensure seat stability. Tighten lock knobs securely. 4. Unscrew nylon lock nuts (8) from socket head cap screws (5). Place cap screws through holes in top of leg connector (6). Invert connector and lay it on floor. Position each leg (9) into connector so that cap screw goes through leg hole. Place strength plate (7) over legs so that cap screw goes through hole in strength plate. Finger-tighten lock nuts, nylon ring up, onto ends of cap screws. 5. Place square base (12) around legs. Remove lock nuts from leg screws (11). Insert a leg screw into each corner of square and through hole in related leg. Finger-tighten lock nut. When all leg screws and lock nuts are in place, securely tighten them. Then securely tighten the lock nuts on the strength plate. 6. Stand leg assembly upright. Insert air cylinder (4), white button up, through hole in top of leg connec- tor until cylinder comes to rest in the leg fixture (6) Part# 90000-06). 7. Place seat on top of cylinder. Apply weight to seat to lock it to the cylinder. CAUTION: To avoid injury, be sure that seat is securely locked to cylinder before sitting on stool. 8. Raise or lower seat by lifting up on the seat adjustment lever beneath seat. Lower the lever to lock seat at desired height. 9. If necessary, you may adjust the leg feet (15) slightly so that the stool rests perfectly flat on the floor. Do not unscrew the leg foot so far as to make the connection between foot and leg un- stable. Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA www.craftsman.com
5
Embed
WORKSHOP STOOL - Searsdownload.sears.com/own/spin_prod_683880001.pdf · this Craftsman Workshop Stool fails due to ... Saque todas las piezas de ta caja de envio. ... Pase los tornittos
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
WORKSHOP STOOLModel 875.618281 Black
Model 875.528280 BlueModel 875.528290 Silver
Model 875.528300 GreenModel 875.528310 RedModel 875.528320 Yellow
One-Year Full Warranty
For one year from the date of purchase, ifthis Craftsman Workshop Stool fails due todefect in materials or workmanship, return it
to any Sears store or other Craftsman outletin the United States for free repair or re-
placement.
This warranty gives you specific legal rights,
and you may also have other rights that varyfrom state to state.
Sears, Roebuck and Co., Dept. 817WA,Hoffman Estates, IL 60179
SAFETY INSTRUCTIONS:
WEAR SAFETY GLASSES when assem-
bling this product.
BE CAREFUL of possible sharp edges.
DO NOT stand on this product. You may
fall which may cause personal injury.
PARTS
See illustration on back of page.
NOTE: The stool seat and backrest are pre-assembled prior to shipment.
ASSEMBLY and OPERATION
INSTRUCTIONS
For assembly hex key (13) and a mini wrench (14)are supplied.
1. Remove all parts from shipping carton. Remove allpackaging material from parts. Check partsagainst parts list before beginning assembly. If anyparts are missing, call 1-800-290-9054.
2. Insert upper end of each backrest support bar (3)into backrest (1) so that one of the two springlocks snaps into place.Be sure to snap each support bar into backrest atsame height.
3. Loosen lock knobs on underside of seat (2)enough so that you can insert the lower end ofeach support bar into the seat bracket. Insertsupport at least 4 inches to ensure seat stability.Tighten lock knobs securely.
4. Unscrew nylon lock nuts (8) from socket head capscrews (5). Place cap screws through holes in topof leg connector (6). Invert connector and lay it onfloor. Position each leg (9) into connector so thatcap screw goes through leg hole. Place strengthplate (7) over legs so that cap screw goes throughhole in strength plate. Finger-tighten lock nuts,nylon ring up, onto ends of cap screws.
5. Place square base (12) around legs. Remove locknuts from leg screws (11). Insert a leg screw intoeach corner of square and through hole in relatedleg. Finger-tighten lock nut. When all leg screwsand lock nuts are in place, securely tighten them.Then securely tighten the lock nuts on the strengthplate.
6. Stand leg assembly upright. Insert air cylinder (4),white button up, through hole in top of leg connec-tor until cylinder comes to rest in the leg fixture (6)Part# 90000-06).
7. Place seat on top of cylinder. Apply weight to seatto lock it to the cylinder. CAUTION: To avoid injury,be sure that seat is securely locked to cylinderbefore sitting on stool.
8. Raise or lower seat by lifting up on the seatadjustment lever beneath seat. Lower the lever tolock seat at desired height.
9. If necessary, you may adjust the leg feet (15)slightly so that the stool rests perfectly flat on thefloor. Do not unscrew the leg foot so far as tomake the connection between foot and leg un-stable.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USAwww.craftsman.com
Si esta Banqueta de Taller Craftsman falladentro de un a_o a partir de la fecha decompra debido a un defecto de materiales o
fabricaci6n, devuelvala a cualquiera tiendaSears o tienda minodsta de Craftsman en los
Estados Unidos para su reparaci6n oreemplazo gratis.
Esta garantia le da derechos legalesespecificos, y usted podria tambien tener
otros derechos que varian de estado aestado.
Sears, Roebuck and Co., Dept. 817WA,Hoffman Estates, IL 60179
INSTRUCCIONES DE SEGURIDAD:
USE GAFAS DE SEGURIDAD cuando
ensamble este producto.
TENGA CUIDADO con los posiblesbordes afilados.
. NO SE PARE sobre este producto. Puede
caerse y causar una lesi6n personal.
PIEZAS
Vea la ilustraci6n al dorso de la p&gina.
NOTA: El asiento y respaldar de la banquetahan sido preensamblados antes del envio.
ENSAMBLE y OPERACION
INSTRUCCIONES
Se ha suministrado para et ensamble una chavetahexagonal (13) y una mini llave (14) .
1. Saque todas las piezas de ta caja de envio. Quite todoel material de embalaje de las piezas. Revise laspiezas contra la tista de piezas antes de comenzar etensamble. Si falta alguna pieza, ltame al 1-800-290-9054.
2. Inserte et extremo superior de cada barra de apoyodet espatdar (3) en el respaldar (1), de forma que unode los dos cierres de resorte encaje en su posici6n.AsegQrese de encajar cada barra de apoyo en etrespaldar a ta misma altura.
3. Afloje las peritlas de fijaci6n que estan debajo detasiento (2) lo suficiente para que pueda introducir etextremo inferior de cada barra de apoyo en et soportedet asiento. Inserte et apoyo pot lo menos 4 pulgadaspara asegurar ta estabitidad del asiento. Apriete lasperittas de fijaci6n con seguridad.
4. Destornitle tas contratuercas de nylon (8) de lostornittos de capucha de cabezal hueco (5). Pase lostornittos de capucha pot los orificios en ta parte dearriba det conector de la pata (6). Invierta et conector yacuesteto en et piso. Posicione cada pata (9) en etconector de forma que et tornitlo de capucha pase poret orificio de la pata. Coloque la placa de resistencia(7) sobre las patas de forma que et tornitlo decapucha pase por et orificio en dicha placa. Aprietecon las manos las contratuercas, con et anitlo denit6n hacia arriba, hacia los extremos de los tornitlosde capucha.
5. Coloque ta base cuadrada (12) alrededor de taspatas. Quiete tas contratuercas de los tomiltos de laspatas (11). Inserte un tornitlo de pata en cada esquinadet cuadrado y por et orificio de la patacorrespondiente. Apriete ta contratuerca con tasmanos. Cuando haya puesto todos los tornittos y tascontratuercas en su posici6n, aprietelos conseguridad. Luego, tambien apriete tas contratuercasen ta placa de resistencia.
6. Coloque et ensamble de la pata en posici6n vertical.Inserte et citindro de aire (4), con et bot6n blancohacia arriba, pot el orificio en ta parte de arriba delconector de la pata hasta que et cilindro descanse enet aditamento de la pata (6) (Pieza # 90000-06).
7. Coloque el asiento arriba det citindro. Aptique un pesoal asiento para trabarlo al citindro. PRECAUCION: Paraevitar lesiones, asegQrese de que et asiento este bientrabado al citindro antes de sentarse en la banqueta.
8. Sube o baje et asiento tevantando la palanca deajuste det asiento que esta debajo det asiento. Baje lapalanca para trabar et asiento a ta altura deseada.
9. Si es necesario, puede ajustar ligeramente ta puntade la pata (15) para que ta banqueta descanseperfectamente plana en et piso. No destornitle muchola punta de la pata porque esto hace que la conexi6nentre la punta y la pata sea inestable.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 EE.UU.www.craftsman.com