WorkFit-A, Single LCD Mount, LD - Ergotron · WorkFit-A, Single LCD Mount, LD User's Guide - English ... If movements are too easy or difﬁ cult or if product ... 40:16 PM ...

888-45-298-W-02 rev.L • 12/15 1 of 16

WorkFit-A, Single LCD Mount, LD

User's Guide - EnglishGuía del usuario - EspañolManuel de l’utilisateur - FrançaisGebruikersgids - DeutschBenutzerhandbuch - NederlandsGuida per l’utente - ItalianoAnvändarhandbok - svenskaユーザーガイド : 日本語用户指南 : 汉语

IncludesConstant Force™Technology

ENGLISH

ASSEMBLY INSTRUCTIONS

For the latest User Installation Guide please visit: www.ergotron.com

For local customer care phone numbers visit: http://contact.ergotron.comFor Service visit: www.ergotron.comFor Warranty visit: www.ergotron.com/warranty

Learn more about ergonomic computer use at:

www.computingcomfort.org

Set Your Workstation to Work For YOU!

Height Position top of screen slightly below eye level. Position keyboard at about elbow height with wrists fl at. Distance Position screen an arm's length from face—at least 20” (508mm). Position keyboard close enough to create a 90˚ angle in elbow. Angle Tilt screen to eliminate glare. Tilt the keyboard back 10° so that your wrists remain fl at.

To Reduce FatigueBreathe - Breathe deeply through your nose.Blink - Blink often to avoid dry eyes.Break • 2 to 3 minutes every 20 minutes• 15 to 20 minutes every 2 hours.

888-45-298-W-02 rev.L • 12/152 of 16

5 - 15 lbs(2.3-6.8 kg)

A

< 5 lbs (2.27 kg)

< 2 lbs (0.9 kg)

B

C

A+B+C < 20 lbs (9.1 kg)

0.78"-2.56" (20-65mm)

0.78"-2.56" (20-65mm)

0.5"-2.5" (13-64mm)

Arm lowers along an arc. Pull Arm toward you as

you lower from the highest position.

827-975

ENGL

ISH

Warning: Because mounting surface materials can vary widely, it is imperative that you make sure mounting surface is strong enough to handle mounted product

and equipment.

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

Adjust the height of your desk (or chair and footrest) to allow the keyboard to lower to your sitting elbow height for ergonomic computing.

Caution:

To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to follow these

instructions may result in equipment damage or personal injury.

Arm lowers along an arc. Pull arm towards you as you lower from the highest

position.

CAUTION! Tipping Hazard. Support the stand until the clamp is securely

tightened. Failure to follow these instructions may result in the stand tipping over

causing possible equipment damages and or personal injury.

Safety

Caution:

DO NOT route cables on top of arm. Failure to follow these instructions may result in equipment damage

and/or personal injury.

888-45-298-W-02 rev.L • 12/15 3 of 16

360˚

20"(508 mm)

20˚

10˚

5"(127 mm)

85˚

A B C D E F

1

2

3

4

5

6

7

1x 1x

1x 4x

2x

M4 x 10mm

M4 x 10mm

4x

8x

1x

1x

1x

M3 x 6mm

M5 x 8mm

1/4"

1/4”1x8mm

1x

4 mm8x

1x

1x

M4x16mm

1x

1x

1x1x 2x

2xM6 x 45mm

1x

1x

M5 x 35mm

ENGLISH

888-45-298-W-02 rev.L • 12/154 of 16

1

12"

(300 mm)

18"

(460 mm)

16"

(410 mm)

10"

(260 mm)

12.75"

(320 mm)

12.75"

(320 mm)

12.75"

(320 mm)

12.75"

(320 mm)

Top View

Top View

12.75"

(320 mm)9.5"

(250 mm)

9.5"

(250 mm)9.5" (250 mm)

9.5"

(250 mm)

10"

(260 mm)

16"

(410 mm)

12.75"

(320 mm)

1 2

3 4

55

6

6

ENGL

ISH

With Expanded Arm Extension With Expanded Arm Extension

Arm Extension and Desk Size:

The keyboard tray is designed to extend over the edge of your desk. You can expand the extension of the arm if

you need to based on your desk size. To determine if you need to expand your arm extension, refer to the 4 desk

dimensions below:

CLAMP

CLAMP

CLAMP

GROMMET HOLE

GROMMET HOLE

GROMMET HOLE

To expand the arm extension, follow instructions on

next page.

Grommet hole can

be located anywhere

along this arch.

Grommet hole can

be located anywhere

along this arch.

To expand the arm extension, follow instructions on next page.

CAUTION: Base must be completely on desk surface.

Failure to follow these instructions may result in

equipment damage or personal injury.

888-45-298-W-02 rev.L • 12/15 5 of 16

4 mm

d1 d2 d3

b c da180˚ 180˚

ENGLISH

How to expand the arm extension.

Remove the 4 screws at the

base using the provided 4mm

hex wrench.

Flip the base around (turn

180 degrees.

Re-insert the 4 screws and tighten

with the 4mm hex wrench.

888-45-298-W-02 rev.L • 12/156 of 16

1/4"

1/4”

8mm

2 0.78"-1.78" (20-45mm) 1.70"-2.56" (43-65mm) 4 mm

7

8

ENGL

ISH

Warning: Because mounting surface materials can vary widely, it is imperative that you make

sure mounting surface is strong enough to handle mounted product and equipment.

Mount arm to desk.

Tighten the bolts with the provided 8 mm wrench.

Clamp confi gurations for diff erent desk thickness

OPTIONAL GROMMET HOLE MOUNT

- Follow these instructions if you want to change your clamp to a grommet

hole mount.

CAUTION! Tipping Hazard. Support the stand until

the clamp is securely tightened. Failure to follow

these instructions may result in the stand tipping

over causing possible equipment damages and or

personal injury.

888-45-298-W-02 rev.L • 12/15 7 of 16

a

c

b

d

4 mm

1x1x

1x

1x

0.78"-2.56"

(20-65mm)

0.5"-2.5"

(13-64mm)

ENGLISH

CAUTION: Bolt must be centered

in hole.

Remove clamp bracket screws with

4mm hex wrench.

Insert provided bolt into provided grommet

plate. Attach grommet plate with 4 mm hex

wrench and screws removed in step b.

Remove clamp plate screws with

4mm hex wrench. Retain screws.

Position arm with attached grommet plate over

grommet hole (make sure bolt is centered in

hole). Thread grommet bracket and wing nut

onto bolt and tighten.

OPTIONAL GROMMET HOLE MOUNT

- Follow these instructions if you want to change your clamp to a grommet

hole mount.

888-45-298-W-02 rev.L • 12/158 of 16

4 mm2xM6 x 45mm

3

2x

a

b

cM5 x 35mm

ENGL

ISH

WARNING!

Screws must be tightened to keep

product secure. Failure to follow these

instructions will create an unstable

situation and may result in equipment

damage or personal injury.

888-45-298-W-02 rev.L • 12/15 9 of 16

41xa b

c2x

M4x16mm

ENGLISH

888-45-298-W-02 rev.L • 12/1510 of 16

5 a

b 1xM5 x 8mm4 mm

60°

M3 x 6mm1x

M4 x 10mm

M4 x 10mm

4x

4x

ENGL

ISH

888-45-298-W-02 rev.L • 12/15 11 of 16

1x

4x

8 1x

M4 x 10mm

4x

7 a

b

c

ENGLISH

888-45-298-W-02 rev.L • 12/1512 of 16

9

8x

1x

ENGL

ISH

NOTE: Leave enough slack in cable to allow full range of motion.

Caution:

To avoid the potential to pinch cables it is important to follow the cable routing instructions in this manual. Failure to

follow these instructions may result in equipment damage or personal injury.

Caution:

DO NOT route cables on top of arm.

Failure to follow these instructions

may result in equipment damage

and/or personal injury.

888-45-298-W-02 rev.L • 12/15 13 of 16

10

1/4"

1/4”

8mm

1

2

3

a

Adjustment Step

ENGLISH

Increase Lift StrengthIf the mounted weight is too heavy or this product does not stay up when raised, then you'll need to increase Lift Strength:

Decrease Lift StrengthIf the mounted weight is too light or this product does not stay down when lowered, then you'll need to decrease Lift Strength:

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

888-45-298-W-02 rev.L • 12/1514 of 16

b

c

1/4"1/4”

8mm

ENGL

ISH





888-45-298-W-02 rev.L • 12/15 15 of 16

d 1/4"1/4”

8mm

e 1/4"1/4”

8mm

f4 mm

ENGLISH

Increase FrictionIf this product moves too easily from side-to-side, then you'll need to increase friction:

Decrease FrictionIf this product is too diffi cult to move from side-to-side, then you'll need to decrease friction:

Increase FrictionIf this product moves too easily, then you'll need to increase friction:

Decrease FrictionIf this product is too diffi cult to move, then you'll need to decrease friction:

Increase FrictionIf this product moves too easily, then you'll need to increase friction:

Decrease FrictionIf this product is too diffi cult to move, then you'll need to decrease friction:

888-45-298-W-02 rev.L • 12/1516 of 16

f

4 mm

1

2

3

ENGL

ISH

Loosen these two screws.

Loosen or tighten this bolt to adjust tilt to desired angle.

Tighten to tilt up.

Loosen to tilt down.

After desired tilt is achieved, retighten these

two screws to secure.

WARNING!

Screws must be tightened to keep product secure.

Failure to follow these instructions will create an

unstable situation and may result in equipment

damage or personal injury.

Angle Setting Adjustment

WorkFit-A, Single LCD Mount, LD - Ergotron · WorkFit-A, Single LCD Mount, LD User's Guide - English ... If movements are too easy or difﬁ cult or if product ... 40:16 PM ...

Documents