Work Supports - vektek.com...10-0715-06 10-0815-06 0.92 1.00 0.58 2.36 For use with S/A fluid advance Work Supports only. B Threaded hole for Work Support C Feeder Cap or Lock Nut

© Vektek, April 2019 800-992-0236 www.vektek.com

nAvailable in: 1,000, 2,500 and 4,000 lbs. nNormally retracted plungers do not interfere with part loading. Advance them with hydraulic pressure, exerting only spring force to bring the plunger into contact with your part. Hydraulic pressure then automatically sequences, “freezing” the plunger properly against the part. nVentless configuration and built in wiper keeps chips and debris out, reducing the chance of plunger/sleeve sticking or binding. nStainless steel plunger and sleeve assemblies help guard against corrosion in most machining environments.

Plunger and sleeve assemblies designed to help guard against corrosionin most machining environments.

Standard SAE porting and alternate O-Ring manifold face seal is located in the base of the support for bolt down in stal la tion. The base can be removed for direct cartridge mounting.

* Support capacities are listed at 5,000 psi maximum operating pressure. Support capacities for other pressures must be determined by consulting the capacity graph on the next page. ** Restrict flow rate to a maximum of 130 cu. in./minute. *** For cartridge mount models, see cavity dimensions on page B-31.

NOTE: The maximum system backpressure a fluid advance work support can overcome is 10 psi. Returning backpressure greater than 10 psi may cause slow or failed retraction.

ILS100700 REV P4000 lb.1000 & 2500 lb.

Model No.

Support Capacity

(lbs)

Mounting Style***

Contact Force**

(lbs)

Stroke(in)

Base Dimensions

(in.)

Retracted Height

(in.)

Oil Capacity**(cu. in.)

Fluid Advance Supports, hydraulic pressure lifts spring which lifts plunger, hydraulic pressure locks.

10-0706-04 1,000Cartridge 1 - 6

0.25N/A

2.12 0.0810-0706-14 1,400 0.50 2.62 0.0910-0806-05 1,000

SAE/Manifold 1 - 60.25

0.90 X 1.31 X 1.752.51 0.16

10-0806-15 1,400 0.50 3.01 0.1710-0708-07 2,500

Cartridge 3 - 100.25

N/A2.83 0.12

10-0708-17 3,000 0.50 3.33 0.1410-0808-07 2,500

SAE/Manifold 3 - 100.25

1.25 X 1.50 X 2.313.25 0.19

10-0808-17 3,000 0.50 3.75 0.2110-0715-06

4,000Cartridge

8 - 12 0.50N/A 2.85 0.59

10-0815-06 SAE/Manifold 0.99 X 2.88 X 3.19 3.25 0.65

DimensionsModel No. A B C D E F G H J K L M N P Q R S T V W X Y Z AA˚ AB AC AD AE

Fluid Advance Supports, hydraulic pressure lifts spring which lifts plunger, hydraulic pressure locks.10-0806-05

1-162.51 0.25 1.17

0.90 0.21 0.88 0.62 0.14 1.31 0.66 0.90 0.45 1.75 0.69 1.20 0.51 0.22 0.505/16-18 X 0.20

SAE 2 0.33 0.38 7 0.38 0.69 YES N/A10-0806-15 3.01 0.50 1.67 3/8 -24 x 0.2010-0808-07

1 1/4-163.25 0.25 1.35

1.25 0.36 1.13 0.81 0.19 1.50 0.75 1.06 0.53 2.31 0.94 1.66 0.72 0.28 0.63 7/16-14 X 0.25 SAE 4 0.43 0.38 N/A N/A N/A N/A YES10-0808-17 3.75 0.50 1.8510-0815-06 2 1/4-16 3.25 0.50 1.57 0.99 0.50 2.00 1.50 0.19 2.88 1.44 2.06 1.03 3.19 1.44 2.41 1.03 0.28 0.75 1/2-13 X 0.25 SAE 4 0.63 0.38 N/A N/A N/A N/A YES

B-29

Work Supports

Fluid Advance

www.vektek.com 800-992-0236 © Vektek, April 2019

All dimensions are in inches.

For proper sealing, mating surface must be flat within 0.003 in with a maximum 63 µ in.Ra surface finish.

Fluid Advance

1000 lb 1400 lb 2500 lb 3000 lb

Model No. Model No. Model No. Model No.

10-0706-04 10-0706-14 10-0708-07 10-0708-17

10-0806-05 10-0806-15 10-0808-07 10-0808-17

ILS100703 REV H

SUPP

ORT

FO

RCE

(lb)

0

INPUT PRESSURE (psi)5000

40003000

20001000

500

1000

1500

2000

2500

3000

10-0715-06

10-0815-06

ILS100704 REV E

05000

40003000

20001000

4000

3000

2000

1000

SUPP

ORT

FO

RCE

(lb)

INPUT PRESSURE (psi)

DimensionsModel No. A B C D E F G H J K L M N P Q R S T V W X Y Z AA˚ AB AC AD AE

Fluid Advance Supports, hydraulic pressure lifts spring which lifts plunger, hydraulic pressure locks.10-0806-05

1-162.51 0.25 1.17

0.90 0.21 0.88 0.62 0.14 1.31 0.66 0.90 0.45 1.75 0.69 1.20 0.51 0.22 0.505/16-18 X 0.20

SAE 2 0.33 0.38 7 0.38 0.69 YES N/A10-0806-15 3.01 0.50 1.67 3/8 -24 x 0.2010-0808-07

1 1/4-163.25 0.25 1.35

1.25 0.36 1.13 0.81 0.19 1.50 0.75 1.06 0.53 2.31 0.94 1.66 0.72 0.28 0.63 7/16-14 X 0.25 SAE 4 0.43 0.38 N/A N/A N/A N/A YES10-0808-17 3.75 0.50 1.8510-0815-06 2 1/4-16 3.25 0.50 1.57 0.99 0.50 2.00 1.50 0.19 2.88 1.44 2.06 1.03 3.19 1.44 2.41 1.03 0.28 0.75 1/2-13 X 0.25 SAE 4 0.63 0.38 N/A N/A N/A N/A YES

B-30

Work Supports

Fluid Advance


Cavity Check List √Confirm capacity of item selected.

Note the sealing surface finish requirements.

Minimum depth specification represents the nominal depth of the standard Vektek base dimension.

Confirm cavity drawing is appropriate for the model number used.

Note specified thread depth when cutting threads.

When using a bottoming tap tool, modifications may be required.

When hand tapping threads, perpendicularity is essential.

Cartridge DimensionsModel No. A B C D E F G H J M V W

10-0706-041-16

2.12 0.25 1.680.24 0.21 0.88 0.62 0.14 0.92 0.50

5/16-18 X 0.203/8-24 X 0.2010-0706-14 2.62 0.50 2.18

10-0708-071 1/4-16

2.83 0.25 2.170.31 0.36 1.13 0.81 0.19 1.17 0.63 7/16-14 X 0.25

10-0708-17 3.33 0.50 2.67

10-0715-06 2 1/4-16 2.85 0.50 2.16 0.19 0.50 2.00 1.50 0.19 2.16 0.75 1/2-13 X 0.25

Work Supports

Fluid Advance Cartridges

B-31


.150 MIN.

.281 MAX. THRU TO FLUID PASSAGEANYWHERE ON OR INSIDE A .50" RADIUS

R.50

R.60.590 (REF).150(REF)

R.020MAX.

.090(REF)

.090±.016

2.165(REF)

2.189(REF)

.63 x .09 DEEPANYWHERE ON A .60" RADIUS

-A-2.165 .001

.590 MIN (THREAD DEPTH).150 .020

ILS100707 REV H

WORK SUPPORT CAVITY DIMENSIONS:#4000 SINGLE ACTING FLUID ADVANCE10-0715-06(TORQUE TO 100 Ft.Lbs.)

SEE DETAIL A

2.189±.007 x .090±.016THREAD 2 1/4-16 UN X .150±.020WITH Ø 2.27 X 45° CHAMFER

.002 -A-

Ø.125 DRILL THRUTO Ø.281 HOLE

.002 -A-.002

DETAIL A

63

Work Supports

Fluid Advance Cartridge Cavities

B-32


D

B

C

ATHREADS

ILS309800 REV D

SAE 4

B

C

A

ILS100708 REV G

D

Fluid Advance Work Support Shields

Model No. Work SupportModel No. A B C D

For use with fluid advance Work Supports only

81-0707-01

10-0706-0410-0706-1410-0806-0510-0806-15

10-0706-10 10-0806-10 10-0806-20

10-0706-10-PS 10-0806-20-PS

0.66 0.50 0.30 1.04

81-0708-01

10-0708-0710-0708-1710-0808-0710-0808-17

10-0708-10 10-0808-10 10-0808-20

10-0708-10-PS 10-0808-20-PS

0.85 0.84 0.43 1.38

81-0715-0110-0715-0610-0815-06

0.92 1.00 0.58 2.36

B Threaded hole

for Work Support

CFeeder Cap or

Lock Nut

ILS100709 REV D

A

.001

.002 A

Feeder Caps DimensionsModel No. A B C D

For use with fluid advance Work Supports only30-9872-39 3/4-16 UN .85 .38 1.0030-9872-40 1-16 UN 1.00 .53 1.2530-9872-43 1 1/4-16 UN 1.38 .85 1.5030-9872-46 1 3/4-16 UN 1.47 1.00 2.0030-9872-47 2 1/4-16 UN .99 .59 2.50

Work Support Capacity B C Lock

Nut1000 HC 3/4-16 1.16 N/A

1000/1400/2000 HC 1-161 1.44 N/A2500/3000/4000 HC 1 1/4-161 1.73 64-0012-00

8000 HC 1 3/4-16 2.31 N/A4000 2 1/4-16 2.89 64-0022-00

Machining Specications for Work Supports mounted with a Feeder Cap or Lock Nut

Work Supports

Fluid Advance Accessories

B-33


Gauge

SEQ/PRVCombo Valve

Power PinHydraulicCrowder

Fluid Advance

Work Support

TuffCam™ Top FlangeSwing Clamp

Power PinHydraulicCrowderTuffCam™ Top Flange

Swing Clamp

TuffCam™ BottomFlange Swing Clamp

TuffCam™ BottomFlange Swing Clamp

Fluid Advance

Work Support

PRV Assembly

Gauge

SequenceValve

ThreadedCylinder

ThreadedCylinder

SequenceValve

Model No.

Capacity(lbs)

O-Ring Part No. A B C D E

10-0704-1010-0804-20

1,000(High Capacity)

39-0511-72.185 x .039

.297 .141 .187 .040 1/4-20 UNC-2A

10-0706-04 10-0806-05

1,000(Std. Stroke)

39-0510-59 .236 x .059

.384 .197 .238 .047 5/16-18 UNC-2A

10-0706-14 10-0806-15

1400(Long Stroke)

39-0000-69 .301 x .064

.450 .197 .302 .047 3/8-24 UNF-2A

10-0706-1010-0806-10 10-0806-20

2000(High Capacity)

39-0510-59.236 x .059

.384 .197 .238 .047 5/16-18 UNC-2A

10-0706-1610-0806-1610-0806-26

2,000(Long Stroke

HC)

39-0510-59.236 x .059

.384 .197 .238 .047 5/16-18 UNC-2A

10-0708-0710-0808-07

2,500(Std. Stroke)

55-2500-05.301 x .070

.493 .250 .328 .070 7/16-14 UNC-2A

10-0708-17 3,000 (Long Stroke)

55-2500-05 .301 x .070

.493 .250 .328 .070 7/16-14 UNC-2A10-0808-17

10-0708-1010-0808-1010-0808-20


55-2500-05.301 x .070

.493 .250 .328 .070 7/16-14 UNC-2A

10-0708-1610-0808-1610-0808-26

4,000(Long Stroke

HC)

55-2500-05.301 x .070

.493 .250 .328 .070 7/16-14 UNC-2A

10-0715-0610-0815-06

4,00039-0020-09.364 x .070

.555 .250 .390 .070 1/2-13 UNC-2A

10-0710-1010-0810-20


39-0511-76.472 x .079

.681 .313 .508 .080 5/8-11 UNC-2A

D .005A MIN.

B .010C .003

60

R.020 MAX.

ILS100714 REV G

SELF-PRODUCEDCONTACT BOLT

WORK SUPPORTPLUNGER

O-RING SEAL

E, THREAD

Self-Produced Contact Bolt for Single ActingFluid Advanced Work Support

Work Supports

Fluid Advance Accessories

B-34

Vektek Concept

Work Supports - vektek.com...10-0715-06 10-0815-06 0.92 1.00 0.58 2.36 For use with S/A fluid advance Work Supports only. B Threaded hole for Work Support C Feeder Cap or Lock Nut

Documents