Woodwork City Free Woodworking Plans - A Hall Table...From Fine Woodworking Magazine comes a great article on building a jig for wooden drawer slides. Half blind dovetail with Fine

awlfreeplans.com

Presents

A Hall Table

Disclaimer All plans within our site have been prepared by and are the sole property of awlfreeplans.com.

All plans, within our site, shall not be copied and/or modified without the written consent of awlfreeplans.com.

Table of Contents

Introduction

Legend

Dimensioned Drawings

Details / Sections

Materials List

References

Introduction Here’s a project sure to present a challenge for most of us! Constructed from Walnut, hard

maple, curly maple veneers and Bloodwood this project will provide various challenges such as

router inlay, half blind dovetails, cock beading and veneering to name a few.

Although this can be a challenging project I have added various links and reference information

located at the end of this document to help you in the construction of your Hall Table.

Difficulty: Moderate to advanced woodworking Skills

Overall Dimensions: 15 1/2” Long X 12” Wide 1 ¼”Thick

Materials cost (As shown): $250+

Hours to complete: 40+

2

3

4

5

6

7

8

9

10

11

Material List Rough Dimensions

Parts No L W T Material Sheets BF Price TotalSheet Goods

TopSubstrate 1 46 1/2 12 3/4 3/4 MDF 1 40.00 40.00Veneer Top 1 Curly Maple 1 60.70 60.70Veneer Bottom 1 Maple 1 28.40 28.40

Bottom Shelf Substrate 1 42 10 3/4" MDF 0.00Veneer Top 1 Curly Maple 0.00Veneer Bottom 1 Maple 0.00

Drawer Shelves 3 8 10 1/4" Maple 1 40.00 40.000.00Subtotal 169.10$

LumberTop

Outter band 2 48 2 1/2 1 Hard Maple 2.00 5.50 11.00Outter band 2 12 2 1/2 1 Hard Maple 0.50 5.50 2.75Inner Inlay 2 48 2 1/2 1 Walnut 2.00 6.50 13.00Inner Inlay 2 12 2 1/2 1 Walnut 0.50 6.50 3.25Maple Leaf 1 6 6 1/8 Bloodwood 0.04 10.00 0.38

Bottom Shelf Outter band 2 46 2 7/8 Hard Maple 1.34 5.50 7.38Outter band 2 12 2 7/8 Hard Maple 0.29 5.50 1.60Inner Inlay 2 48 2 7/8 Walnut 1.17 6.50 7.58Inner Inlay 2 12 2 7/8 Walnut 0.29 6.50 1.90

Legs 4 30 2 2 Hard Maple 3.33 5.50 18.33Stretchers Back 1 43 5 3/4 Hard Maple 1.12 5.50 6.16

Front 4 3 1 1/2 3/4 Hard Maple 0.09 5.50 0.52Front 2 43 1Sides 2 10 5 3/4 Hard Maple 0.52 5.50 2.86

Drawers Front 3 12 3 1/2 3/4 Curly Maple 0.66 10.00 6.56Back 3 12 3 1/2 1/2 Maple 0.44 3.50 1.53Sides 6 10 3 1/2 1/2 Maple 0.73 3.50 2.55Beading 3 12 3/4 1/8 Walnut 0.02 2.50 0.06Slides 6 9 1/2 5/8 Hard Maple 0.12 5.50 0.64

Total BF 15.16 Subtotal 88.06$ Hardware

Dominos 5.00 5.00Figure 8's 5.00 5.00

0.00Subtotal Hardware 10.00

FinishesArm-R-Seal 1 qt 1 12.00 12.00Seal-R-Cell 1 Pint 8.00 8.00

Subtotal Finishes 20.00

Project Total 287.16$

12

References “Wish you Veneer”

This video pod cast reviews how to cut your own veneers

“A Pressing Matter” This video pod cast reviews the veneer bags and the veneering process

Inlay tutorial with The Wood Whisperer Here’s a great step by step tutorial Marc created over at Woodworking.org

Popping the curl Here’s a great video by Charles Neil on how to help the figure pop when finishing Wooden Drawer Slide Jig

From Fine Woodworking Magazine comes a great article on building a jig for wooden drawer slides.

Half blind dovetail with Fine Woodworking This article reviews some of the basics of half blind dovetails Handcut Half Blind Dovetails From the fine folks at Popular Woodworking comes a great article on handcut dovetails

13