13.1 2011−08−31 11708422 Marvin Parts Manual CHAPTER 13 WOOD & CLAD ULTIMATE INSWING FRENCH DOORS Table of Contents PAGE History History − Inswing French Door and Ultimate Inswing French Door 13.3 ....................... History − Obsolete Inswing French Door 13.4 .............................................. History − Obsolete Terrace Door 13.7 .................................................... Parts Identification Part Identification − Wood Ultimate Inswing French Door Operator 13.9 ....................... Part Identification − Wood Ultimate Inswing French Door Jamb Detail 13.10 .................... Part Identification − Wood Ultimate Inswing French Door Stationary 13.11 ...................... Part Identification − Wood Ultimate Inswing French Door Single Glaze ADL 13.12 ............... Part Identification − Wood Ultimate Inswing French Door In−Sash Transom 13.13 ............... Part Identification − Wood Ultimate Inswing French Door In−Sash Transom Jamb Detail 13.14 .... Part Identification − Wood Ultimate Inswing French Door Direct Glaze Transom 13.15 ........... Part Identification − Clad Ultimate Inswing French Door Operator 13.16 ........................ Part Identification − Clad Ultimate Inswing French Door Jamb Detail 13.17 ..................... Part Identification − Clad Ultimate Inswing French Door Stationary 13.18 ....................... Part Identification − Clad Ultimate Inswing French Door In-Sash Transom 13.19 ................. Part Identification − Clad Ultimate Inswing French Door In-Sash Transom Jamb Detail 13.20 ...... Part Identification − Clad Ultimate Inswing French Door Direct Glaze Transom 13.21 ............. Parts 13.22 ............................................................................ Weather Strip 13.30 ..................................................................... Wood Parts 13.32 ...................................................................... Aluminum Parts 13.33 ................................................................... Vinyl and Fiberglass Parts 13.35 .......................................................... Panel Replacement 13.36 ................................................................ Sliding Screens and Screen Parts 13.37 ................................................... Swinging Screen Hardware Location ID 13.40 .............................................. Swinging Screens and Screen Parts 13.41 ................................................. Energy Panel for Single Glazed Wood Panels 13.46 ......................................... Combination Door Parts 13.47 ............................................................ Ultimate Inswing French Door Pre 2011 Part Identification − Wood Ultimate Inswing French Door Operator 13.50 ....................... Part Identification − Wood Ultimate Inswing French Door Jamb Detail 13.51 .................... Part Identification − Wood Ultimate Inswing French Door Stationary 13.52 ...................... Part Identification − Wood Ultimate Inswing French Door Single Glaze ADL with EP 13.53 ........ Part Identification − Wood Ultimate Inswing French Door In−Sash Transom 13.54 ............... Part Identification − Wood Ultimate Inswing French Door In−Sash Transom Jamb Detail 13.55 .... Part Identification − Wood Ultimate Inswing French Door Direct Glaze Transom 13.56 ........... Part Identification − Clad Ultimate Inswing French Door Operator 13.57 ........................ Part Identification − Clad Ultimate Inswing French Door Jamb Detail 13.58 ..................... Part Identification − Clad Ultimate Inswing French Door Stationary 13.59 .......................
124
Embed
Wood and Clad Ultimate Inswing French Doors · 2011−08−31 13.1 11708422 Marvin Parts Manual CHAPTER 13 WOOD & CLAD ULTIMATE INSWING FRENCH DOORS Table of Contents PAGE History
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
ULTIMATE INSWING FRENCH DOOR 1993 − PRESENT _ INSWING FRENCH DOOR 1998 − 2005
PRODUCED UNIT TYPE FEATURES OR CHANGES STATUS1993 Wood Ultimate
Inswing FrenchDoor
Unit features 3/4� insulating glass, 4 9/16� or 6 9/16� one piecejambs, top hung screen with optional auto closer, keyed multi-pointlocking system with stainless steel bolts on active panel, astragaland stainless steel head and foot bolts on inactive panel, solidbrass handles on active and inactive panels, adjustable hingeswith hardened steel bearings and beige composite sill. Multiplepanel doors have continuous head jamb and sill.
Early 1998
1994 Wood UltimateInswing FrenchDoor
Transom introduced featuring direct glaze and in-sash versions withsills designed for field mulling.
Present
Combination door introduced featuring storm and screen inserts,weather stripped panels, brass surface mount hinges and headand foot bolts. No handle bore (standard).
Present
Late 1994 Solid brass combination handles introduced. Panels now featurehandle bore (standard).
Present
1996 Clad UltimateInswing FrenchDoor
2/96 Unit features 3/4� insulating glass, 4 9/16� or 6 9/16� onepiece jambs, top hung screen with optional auto closer, keyedmulti-point locking system with stainless steel bolts on active panel,astragal and stainless steel head and foot bolts on inactive panel,solid brass handles on active and inactive panels, adjustablehinges with hardened steel bearings and beige Ultrex sill withbuilt in weep system. Multiple panel doors have continuous headjamb and sill.
Early 1998
In-sash transom introduced. Present
1996 Wood and CladUltimate InswingFrench Door
Adjustable Gold Tone hinge replaces (standard) Sun Goldfinish. Optional finishes available to match hinge finish exactlyto handle finish.
Present
1996 Wood and CladUltimate InswingFrench Door
1/96 Locking rods (and associated parts) on multi−point locking systemswere changed from a hollow aluminum alloy tube with #10 machinethreads to solid stainless steel with 1/4� − 20 threads.1/96 Locking rods (and associated parts) on Inactive panel Head/foot boltlocking systems were changed from a hollow aluminum alloy tube with#10 machine threads to solid stainless steel with 1/4” − 20 threads.10/96 Multi−point locking system changed back to hollow aluminum alloytube with #10 machine threads.3/96 Wood Ultimate Inswing French Door sill changed from Ultrex/Lexantwo piece design to one piece Ultrex with weep system.12/96 Sill threshold (W7551) fabrication change, attaching screwschanged from centered vertical position to offset and angled toward theinterior.
1996
Present
1997
1998
1998
1997 Wood and CladUltimate InswingFrench Door
2/97 Multi−point locking system changed to solid stainless steel lockingrods with 1/4� − 20 threads.
6/97 Multi−point locking rod hole in the stile was enlarged from 3/8” to 5/8”
9/97 End bolt guide and plate were replaced with a one piece design.
1999
Present
Present
1998 Wood and CladTerrace Door,Inswing FrenchDoor, and UltimateInswing FrenchDoor
5/98 Door lines merged into one, revised Ultimate frame and paneldesign. Door sizes expanded to cover replaced product offerings.Available no bore and bore for passage/dead bolt to 7/0 height. Tallerdoors standard with multi−point active panels, optional on all sizes. LVLlocking stile standard. 4� butt hinge standard (bright brass only),adjustable hinge optional. Ultimate option package includes FRP activepanel locking stile, multi−point lock, and adjustable hinges. Top hungsliding screen available on configurations with stationary panel. Woodcombinations and Transoms use existing Ultimate design.
Present
1999 Wood and CladInswing andUltimate InswingFrench Door
5/10/99 (date of manufacture) Multi−point locking system changed tonew design (from Trimco to Amerock). Flush bolt rod changed to newdesign.
Present
2000 Wood and CladInswing andUltimate InswingFrench Door
1/17/00 Changed passage latch lever set and dead bolt to mortise lock(Amerock) that utilize existing Multi−point style handles. Bore only forpassage latch and dead bolt available as option.
1/30/00 Discontinued auto closer for optional top hung screen.
Present
2000 Wood and CladInswing andUltimate InswingFrench Door
8/7/00 PVD Brass hardware available on UIFD. Non handed handle sets. Present
ULTIMATE INSWING FRENCH DOOR
HISTORY
13.42012−12−17 11708422Marvin Parts Manual
PRODUCED UNIT TYPE FEATURES OR CHANGES STATUS2002 Wood and Clad
Ultimate InswingFrench Door
3/02 Stone White becomes a standard color. Arctic White transitionsto a select color. 8/0 height decreases by 2 1/2 inches.
Present
2003 Wood and CladInswing FrenchDoor
3/31/03 Satin Taupe (TP) hardware replaces Brass as standard.Standard door now includes Multi−point lock.
Present
2003 Wood and CladUltimate FrenchDoor
3/31/03 Satin Taupe (TP) hardware replaces Brass as standard. Present
2003 Ultimate InswingFrench Door
Strikes for Satin Taupe, Brushed Chrome, Polished Chrome andWhite are Stainless Steel.
Present
2004 Wood and CladUltimate InswingFrench Door
1/04 Added Oiled Rubbed Bronze and Satin Chrome to availablehardware finishes.
6/14/04 Wood and Clad Direct Glaze transom redesigned. PolishedChrome hardware finish retired.
Present
2005 Wood and CladUltimate InswingFrench Door
1/2005 New options: No lock/bore, bores, mortise latch with deadboltand butt hinges. Locking styles use LVL core. Inswing French Dooroptions now available on Ultimate Door making the Inswing FrenchDoor obsolete.
Present
2005 Wood and CladUltimate InswingFrench Door
6/15/05 Changed jamb leaf on adjustable hinge to closed knuckledesign.
Present
2005 Wood and CladUltimate InswingFrench Door
6/27/05 Introduced Brass PVD and Satin Nickel PVD finishes toFrench door handles, adjustable hinges, and other miscellaneousparts.
Present
2006 Wood and CladUltimate InswingFrench Door
7/24/06 Discontinued retro 6−5 height and replaced with 6−6 height.Frame OSM for 6−6 height is 3/4� taller than 6−5 doors. Frame OSMfor 6−6 width is 11/16� wider (one panel), 1 3/8� wider (two panel) and2 1/16� wider (three panel).
Present
2007 Wood and CladUltimate InswingFrench Door
2/20/07 Introduced raised panels and flat panels as a standard optionfor Marvin French Doors and Commercial Doors.
Introduced new Ultimate Swinging Screen along with an optionalStorm Insert.
Present
2008 Wood and CladUltimate InswingFrench Door
6/02/2008 Introduced charcoal colored high transparency screenmesh (CH HI−TRAN) as an option on all window and door products(including combinations).
Present
2008 Clad UltimateInswing FrenchDoor
7/28/2008 Mixed grain Douglas fir is now a standard option. Present
2009 All 3/23/2009 Added LoĒ3-366� as a standard option for all products.Added Cedro Macho as a standard option for all clad products.
Present
2010 All 2/22/2010 Added Dark Bronze hardware finish option. Present
2011 Clad and WoodUltimate InswingFrench Door
2/28/2011 Redesign incorporating new cladding, frame and sill profiles,F2050 (4 9/16� and F2051(6 9/16�). Optional exterior sill cover availablein Mahogany; Optional interior sill liner available in Oak, Mahogany, orCherry.
2/28/2011 With the 2011 platform release, UIFD swinging and slidingscreen along with the wood combination are shortened .364�.
04/25/2011 Added LoĒ 180� as a standard option for all products.White painted interior finish option introduced for all products.
Present
2012 All 7−30−2012 Stave Core added to our description for current fingerjoint/edge glue construction of door panels. Updated adjustablehinges.10−29−2012 Interior Square Sticking/Glazing Bead option introduced.12−17−2012 Introduced Clear Interior Finish option on all products.
Present
ULTIMATE INSWING FRENCH DOOR
HISTORY
13.52013−06−24 11708422Marvin Parts Manual
PRODUCED UNIT TYPE FEATURES OR CHANGES STATUS
2013 Clad and WoodUltimate InswingFrench Door
4/29/2013 − Introduced Retro 2 Wide CNs on Full Size Heights. NewCNs are 50R68, 50R70, 50R80, 60R68, 60R70, and 60R80. AllRetro sizes, current and new, will be designated with an “R” in theCN. Introduced interior stain options. Stain colors are Wheat, Honey,Leather, Hazelnut, Cabernet and Espresso.
6/24/2013 − Direct Glaze Standardization added upgrades andimprovements to direct glaze products in both wood and clad.Glazing method is silicone and interior tape glazed. Wood beadprofile is W11751.
12/16/2013 − Interior Shades option introduced.
Present
ULTIMATE INSWING FRENCH DOOR
HISTORY
13.62013−04−29 11708422Marvin Parts Manual
OBSOLETE INSWING FRENCH DOOR HISTORY PRODUCED BEFORE 5/98
PRODUCED UNIT TYPE FEATURES OR CHANGES DISCONTINUED
1985 Wood Inswing FrenchDoor
Unit features 3/4� insulating glass, 4 9/16� jambs, brass plated hinges,no panel bore or lock (standard). Unit offered in CN 6-8 height.
Early 1998
Optional panel bore (2 3/4� backset). 1986
Unit featured 4 15/16� top rail and stiles and 8 3/8� bottom rail. 1986
Optional antique brass lever set. 1987
Unit was shipped ’knocked down’ (KD). 1988
Unit featured brass plated head and foot bolts. Late 1989
Brown Lexan sill. 1991
1986 Wood Inswing FrenchDoor
Single glaze and insulating glass ADL munts and sash profileschanged affecting glass and grille sizes. Unit features 4 3/4� top railand stiles and 8 1/8� bottom rail. Optional panel bore (2 3/8� backset).
Early 1998
Transom introduced for the Wood Inswing French Door. Early 1998
1986 Wood French DoorPanel
Introduced CN 7-0 height panels featuring 1 3/4� panels, 12 1/8�bottom rail, no bore or hinge route.
Early 1998
1987 Wood French DoorPanel
Introduced CN 8-0 height panels featuring 1 3/4� panels, 10 3/8�bottom rail, no bore or hinge route.
Early 1998
1987 Wood Inswing FrenchDoor
Sidelites introduced. Early 1998
Optional polished brass plated lever set (Exclusive series) or optionalsolid brass lever set (Designer series).
Late 1989
1987 Clad Inswing FrenchDoor
Unit features 3/4� insulating glass, 4 9/16� jambs, brass platedhinges, no panel bore or lock (standard). Unit offered in CN 6-8 height.Optional panel bore (2 3/8� backset).
Early 1998
Sidelites and transoms introduced. Early 1998
Unit was shipped ’knocked down’ (KD). 1988
Optional polished brass plated lever set introduced (Exclusive series). 1988
Brass plated head and foot bolts. 1989
Optional solid brass lever set introduced. (Designer series). Late 1989
Brown Lexan sill. 1991
Early 1988 Wood Inswing FrenchDoor
KD version discontinued, units available set-up in CN 6-8, CN 7-0 andCN 8-0 heights. Introduced one piece 6 9/16� frame (extended to theexterior).
Early 1998
1988 Interior Colonial DoorPanel
Introduced CN 6-8 height 1 3/8� colonial panels. Panels featuredraised panel design, no bore or hinge route.
1989
Late 1988 Wood French Door Interior Panels
Introduced CN 6-8 and CN 7-0 height panels featuring single glazed1 3/8� panels, no bore or hinge route. CN 6-8 panel has 8 1/8�bottom rail, CN 7-0 panel has 12 1/8� bottom rail.
Present
Late 1988 Clad Inswing FrenchDoor
KD version discontinued, units available set-up in CN 6-8, CN 7-0 andCN 8-0 heights. Introduced 6 9/16� frame (extended to the exterior).
Early 1998
Early 1989 Wood and CladInswing French Doors
Hinge route location changed on CN 8-0 height doors. Early 1998
Plated brass hinges and brown Lexan sill. 1991
Late 1989 Wood and CladInswing French Doors
Introduced optional solid brass lever set designed for Marvin(Exclusive and Designer series discontinued) and solid brass headand foot bolts.
Present
INSWING FRENCH DOOR
HISTORY
13.72013−04−29 11708422Marvin Parts Manual
OBSOLETE INSWING FRENCH DOOR HISTORY PRODUCED BEFORE 5/98
PRODUCED UNIT TYPE FEATURES OR CHANGES DISCONTINUED1991 Wood and Clad
Inswing French DoorsCN 6-5 height introduced including a 4 panel entrance system withcontinuous head jamb and sill. External component parts changedfrom brown to beige.
Early 1998
Lexan sill changed from brown to beige. 1994
1991 Wood Inswing FrenchDoor
Optional multi-point hardware system introduced. 1993
1991 Clad Inswing Optional multi-point (Essve) hardware system introduced. Early 1998
1991 Clad Inswing FrenchDoor
Vinyl glazing bead changed to exterior aluminum cap glazingsystem for 1 lite and ADL insulating glass.
Early 1998
Late 1991 Exterior factory finish available.
1991 Wood Inswing French Combination introduced featuring interchangeable screen andstorm inserts and complete brass hardware.
Early 1998
1992 Wood Inswing FrenchDoors
Simulated divided lite option introduced. Present
1993 Clad Inswing FrenchDoors
Factory applied brick mould casing and simulated divided liteoption introduced.
Present
Late 1993 Brushed chrome finish available for hinges. Present
1994 French Doors Beige Lexan sill changed to beige composite sill. Early 1998
1994 Wood UltimateInswing FrenchDoor
Transom introduced featuring direct glaze and in-sash versions withsills designed for field mulling.
Present
1998 Wood and CladTerrace Door,Inswing FrenchDoor, and UltimateInswing FrenchDoor
5/98 Door lines merged into one, revised Ultimate frame and paneldesign. Door sizes expanded to cover replaced product offerings.Available no bore and bore for passage/dead bolt to 7/0 height. Tallerdoors standard with multi−point active panels, optional on all sizes. LVLlocking stile standard. 4� butt hinge standard (bright brass only),adjustable hinge optional. Ultimate option package includes FRP activepanel locking stile, multi−point lock, and adjustable hinges. Top hungsliding screen available on configurations with stationary panel. Woodcombinations and Transoms use existing Ultimate design.
Present
INSWING FRENCH DOOR
HISTORY
13.82013−04−29 11708422Marvin Parts Manual
OBSOLETE INSWING TERRACE DOOR HISTORY
PRODUCED UNIT TYPE FEATURES OR CHANGES DISCONTINUED
1982 Wood Terrace Door Unit features 3/4� insulating glass, 4 9/16� jambs, brass platedhinges, ’retro’ sizing and 1, 2 or 3 panel widths.
1998
Panel bore (2 3/4� backset). 1986Antique brass lever and lockset. 1987Combination with screen and storm inserts. No hinge or handle package. 1991Brown Lexan sill. 1991
1984 Terrace DoorScreens
In the mid 1980s several different screen rollers were used in theTerrace door line. To determine what is currently available forreplacement consult the Screen and Screen Parts and ObsoleteScreen Parts pages of this section.
1985 Wood Terrace Door Sidelites introduced featuring continuous head jamb and sill,(available as a stand alone or entry system configuration).
1998
Introduced CN 2-0 width panel. 1998
1986 Wood Terrace Door Single glaze and insulating glass munt profile changed. Glass rabbetdepth changed from 3/4� to 9/16�.
1998
Panel bore (2 3/8� backset). 1992
1986 Marv-A-GardTerrace Door
Unit features aluminum clad exterior, 3/4� insulating glass,4 9/16� jambs, brass plated hinges, ’retro’ sizing and 1, 2 or 3panel widths. (The term Marv-A-Gard was discontinued in late1986).
1987 Wood and Clad Transoms introduced, available factory mulled. 1998Terrace Door Polished brass plated lever set introduced. (Exclusive series) 1988
Optional solid brass lever set introduced. (Designer series) 1989
1988 Wood and CladTerrace Door
Brass plated lever and lockset now optional. 1989
Late 1989 Wood and CladTerrace Door
Optional solid brass hinges and optional solid brass lever set designedfor Marvin (Exclusive and Designer series discontinued).
1998
1990 Wood Terrace Door Optional multi-point (Essve) hardware system introduced. 1993
1990 Clad Terrace Door Optional multi-point (Essve) hardware system introduced. 1998
1991 Clad Terrace Door Clad glazing cap became a standard feature. 1998
1991 Wood Terrace Door Combination redesigned featuring handle package (standard) and anadjustable sweep.
1998
Combination hinge introduced (standard). 1993
1991 Wood and Clad Brown Lexan sill changed to beige. 1994Terrace Door External component parts changed to beige. 1998
1992 Wood and CladTerrace Door
Panel bore now optional. 1998
1992 Wood Terrace Door Simulated divided lite option introduced. 1998
1993 Clad Terrace Door Clad simulated divide lite and factory installed clad brick mouldcasing introduced.
1998
1993 Wood Terrace Door Surface mount Combination hinges introduced. 1998
1994 Wood and CladTerrace Door
Lexan sill changed to composite sill. 1998
1998 Wood and CladTerrace Door,Inswing FrenchDoor, and UltimateInswing FrenchDoor
5/98 Door lines merged into one, revised Ultimate frame and paneldesign. Door sizes expanded to cover replaced product offerings.Available no bore and bore for passage/dead bolt to 7/0 height. Tallerdoors standard with multi−point active panels, optional on all sizes. LVLlocking stile standard. 4� butt hinge standard (bright brass only),adjustable hinge optional. Ultimate option package includes FRP activepanel locking stile, multi−point lock, and adjustable hinges. Top hungsliding screen available on configurations with stationary panel. Woodcombinations and Transoms use existing Ultimate design.
Present
WOOD AND CLAD TERRACE DOOR
HISTORY
13.92013−05−20 11708422Marvin Parts Manual
NOTE: Not to scale; specifications subject to change without notice.
1. Head Jamb Brick Mould Casing, W10472. Head Jamb Parting Stop, W108623. Head Jamb4. Head Jamb Parting Stop Weather Strip5. Top Rail6. Insulating Glass7. Glazing Cap, W42308. Glazing Bead, V9339. Bottom Rail
10. Door Sweep11. Sill12. Sill Interior Filler Block13. Ext. Mahogany Sill Cover−opt.14. Int. Oak Sill Liner −opt.15. Side Jamb Brick Mould Casing16. Side Jamb17. Adjustable Hinge18. Stile19. Interior Handle Assembly20. Exterior Handle Assembly21. Active Panel Locking Stile22. Inactive Panel Locking Stile23. Astragal Weather Strip, V79624. Stile Weather Strip, V78025. Astragal Cover26. Astragal Base27. Side Jamb Parting Stop28. Side Jamb Parting Stop Weather Strip, V1947
WUIFDOperator XX
9
14
11
13
10
2
5
431
12
11
9
6
2
27
28
25
10
23
7
8
2221
6
20
19
18
15
16
17
7
8
5
43
1
6 9/16� Jambs
Sill Options
Jamb XX−L
Head Jamband Sill
24
26
WOOD ULTIMATE INSWING FRENCH DOOR
PART IDENTIFICATION
13.102013−04−29 11708422Marvin Parts Manual
NOTE: Not to scale; specifications subject to change without notice.
WUIFDJamb Details
1. Side Jamb Brick Mould Casing2. Side Jamb3. Mull Casing Base4. Screen Astragal5. Mull Casing Cover6. Astragal Weather Strip7. Stile Weather Strip8. Side Jamb Parting Stop9. Stile
NOTE: Not to scale; specifications subject to change without notice.
WUIFDStationary
1. Head Jamb Brick Mould Casing2. Head Jamb Parting Stop, W108623. Head Jamb4. Head Jamb Parting Stop Weather Strip5. Head Jamb Spacer Tack6. Top Rail7. Glazing Cap, W42308. Glazing Bead, V9339. Insulated Glass
10. Bottom Rail11. Door Sweep12. Sill13. Sill Interior Filler Block14. Side Jamb Brick Mould Casing15. Side Jamb16. Narrow Stile17. Side Jamb Parting Stop18. Side Jamb Parting Stop Weather Strip19. Stationary Stile20. Jamb Spacer Tack
Head Jamband Sill
Single Panel Sidelite Jamb
Stationary Jamb
13
11
12
10
8
7
5
9
6
43
2
1
20
18
1714
10
98
19
16
15
WOOD ULTIMATE INSWING FRENCH DOOR
PART IDENTIFICATION
13.122013−04−29 11708422Marvin Parts Manual
NOTE: Not to scale; specifications subject to change without notice.
WUIFDSingle Glaze ADL with Ultimate Swinging Screen and Energy Panel
1. Head Jamb Brick Mould Casing2. Head Jamb3. Head Jamb Parting Stop4. Head Jamb Parting Stop Weather Strip, V7965. Top Rail6. Screen Frame7. Screen Mesh8. Energy Panel9. Glazing Bead
10. Filler Strip11. ADL Muntin12. Single Glaze Glass13. Bottom Rail14. Door Sweep15. Sill16. Sill Interior filler Block17. Ext. Mahogany Sill Cover opt.18. Int. Oak Sill Liner − opt.19. Side Jamb Brick Mould Casing20. Side Jamb21. Stile22. Side Jamb Parting Stop23. Mull Casing Base24. Screen Astragal25. Astragal Weather Strip26. Stile Weather Strip27. Adjustable Hinge28. Int. Handle Assembly29. Ext Handle Assembly30. Active Panel Locking Stile31. Side Jamb Parting Stop Weather Strip, V1947
6 9/16� Jamb
Sill Options
Head Jamband Sill
Jamb
8
9 26
31
30
29
2827
76
25
24
23
810
9
1121
22
20
19
5
6
421
3
15
18
13
17
14
12
13
11
10
9
8
7
6
42
1
16
15
3
14
5
WOOD ULTIMATE INSWING FRENCH DOOR
PART IDENTIFICATION
13.132013−04−29 11708422Marvin Parts Manual
WUIFD In−Sash TransomJamb Details
NOTE: Not to scale; specifications subject to change without notice.
1. Side Jamb2. Side Jamb Brick Mould Casing3. Insulating Glass4. Side Jamb Weather Strip, V1925. Side Jamb Parting Stop6. Side Jamb Parting Stop Weather Strip7. Mull Casing Weather Strip8. Stile Weather Strip9. Mull Casing Cover
NOTE: Not to scale; specifications subject to change without notice.
WUIFD IN−SASH TRANSOM
1. Head Jamb Brick Mould Casing2. Head Jamb3. Head Jamb Parting Stop4. Head Jamb Parting Stop Weather Strip5. Head Jamb Weather Strip6. Top Rail Block7. Top Rail8. Glazing Bead9. Insulated Glass
10. Glazing Cap11. Bottom Rail12. Sill Filler Weather Strip13. Sill14. Sill Filler15. Side Jamb Brick Mould Casing16. Side Jamb17. Stile18. Side Parting Stop19. Side Parting Stop Weather Strip20. Side Jamb Weather Strip21. Jamb Spacer Tack
Head Jamband Sill
Jamb
6 9/16� Jamb
WOOD ULTIMATE INSWING FRENCH DOOR
PART IDENTIFICATION
13.152013−06−24 11708422Marvin Parts Manual
1. Head Jamb Brick Mould Casing2. Head Jamb3. Insulating Glass4. Glazing Bead (W11751)5. Sill Nose, (W12059)6. Sill7. Jamb Brick Mould Casing8. Side Jamb
WUIFDDIRECT GLAZE TRANSOM
Head Jamband Sill
Jamb
NOTE: Not to scale; specifications subject to change without notice.
1 2
3
4
56
7
8 43
WOOD ULTIMATE INSWING FRENCH DOOR
PART IDENTIFICATION
13.162013−04−29 11708422Marvin Parts Manual
NOTE: Not to scale; specifications subject to change without notice.
1. Head Jamb Nailing Fin/Drip Cap2. Head Jamb Cladding3. Head Jamb4. Head Jamb Parting Stop, A19655. Head Jamb Parting Stop Weather Strip, V7966. Top Rail Cladding7. Top Rail8. Glazing Cap, W42309. Insulating Glass
10. Glazing Bead, V93311. Bottom Rail Cladding12. Bottom Rail13. Door Sweep14. Sill Interior Filler Block15. Sill16. Ext. Mahogany Sill Cover opt.17. Int. Oak Sill Liner opt.18. Side Nailing Fin19. Side Jamb Cladding20. Side Jamb21. Adjustable Hinge22. Stile23. Stile Cladding24. Interior Handle Assembly25. Exterior Handle Assembly26. Active Panel Locking Stile27. Inactive Panel Locking Stile28. Astragal Weather Strip, V79629. Stile Weather Strip, V78030. Mull Casing Cover31. Clad Astragal32. Side Jamb Weather Strip, V194733. Side Jamb Parting Stop
CUIFDOPERATOR XX
Jamb XX L
Head Jamband Sill
6 9/16� Jamb
Sill Options15
1312
33
32
30
17
7
6
16
2
4
53
15
14
13
12
3129
28
8
10
2726
9
25
24
23
22
19
18
20
21
11
8
109
7
6
4
53
2
1
CLAD ULTIMATE INSWING FRENCH DOOR
PART IDENTIFICATION
13.172013−07−12 11708422Marvin Parts Manual
NOTE: Not to scale; specifications subject to change without notice.
CUIFDJamb Detail
1. Jamb Nailing Fin2. Side Jamb3. Mull Post4. Mull Cap Swinging Screen, A20495. Mull Casing Cover6. Clad Astragal7. Side Jamb Frame Cladding8. Stile Weather Strip, V7809. Astragal Weather Strip, V796
10. Side Jamb Parting Stop, A196511. Stile12. Stile Cladding13. Insulating Glass14. Screen Frame15. Screen16. Active Panel Locking Stile17. Interior Handle Assembly18. Exterior handle Assembly19. Adjustable Hinge20. Side Parting Stop Weather Strip21. Glazing Bead, V93322. Glazing Cap, W423023. Inactive Panel Locking Stile24. Space Tack
NOTE: Transoms also available with 6 9/16� jambs.
OX−L Jamb
XX−L Jamb
OXO−L Jamb
OXXO−L Jamb
4
4
75
24
4
2321
20
19
18
17
16
9
8
10
6
13
2
1
22
12
11
3
1415
CLAD ULTIMATE INSWING FRENCH DOOR
PART IDENTIFICATION
13.182013−04−29 11708422Marvin Parts Manual
NOTE: Not to scale; specifications subject to change without notice.
Head Jamband Sill
CUIFDSTATIONARY
1. Head Jamb Nailing Fin/Drip Cap2. Head Jamb3. Head Jamb Cladding4. Head Jamb Parting Stop, A19655. Head Jamb Parting Stop Weather Strip, V7966. Head Jamb Spacer Tack7. Top Rail Cladding8. Top Rail9. Glazing Cap, W4230
10. Glazing Bead, V93311. Insulating Glass12. Bottom Rail Cladding13. Bottom Rail14. Door Sweep15. Sill16. Sill Interior Filler Block17. Jamb Nailing Fin18. Side Jamb19. Side Jamb Cladding20. Side Jamb Parting Stop, A196521. Side Jamb Parting Stop Weather Strip, V194722. Narrow Stile23. Narrow Stile Cladding24. Stationary Stile25. Stationary Stile Cladding26. Jamb Spacer Tack
Single Panel Sidelite Jamb
Stationary Jamb Detail
21
10 9
26
1125
24
23
22
20
19
18
17
16
15
11
6
21
14
1312
10
9
43
5
7
8
CLAD ULTIMATE INSWING FRENCH DOOR
PART IDENTIFICATION
13.192013−04−29 11708422Marvin Parts Manual
NOTE: Not to scale; specifications subject to change without notice.
CUIFD IN−SASH TRANSOM
1. Head Jamb Nailing Fin/Drip Cap2. Head Jamb Cladding3. Head Jamb Parting Stop, A19654. Head Jamb5. Head Jamb Weather Strip, V1926. Head Jamb Parting Stop Weather Strip, V7967. Top Rail Block8. Top Rail9. Top Rail Cladding
10. Glazing Bead, V93311. Insulating Glass12. Glazing Cap, W423013. Bottom Rail Cladding14. Bottom Rail15. Sill Filler Weather Strip, V204516. Sill Filler, W1108417. Sill Cladding18. Sill19. Sill Nailing Fin20. Jamb Nailing Fin21. Side Jamb22. Side Jamb Cladding23. Side Parting Stop Weather Strip24. Stile25. Side Cladding26. Side Jamb Weather Strip27. Side Parting Stop28. Spacer Tack
Head Jamband Sill
Jamb
6 9/16� Jamb
CLAD ULTIMATE INSWING FRENCH DOOR
PART IDENTIFICATION
13.202013−04−29 11708422Marvin Parts Manual
NOTE: Not to scale; specifications subject to change without notice.
CUIFD In−Sash Transom Jamb Detail
1. Side Jamb2. Side Nailing Fin3. Insulating Glass4. Side Jamb Weather Strip, V1925. Side Jamb Parting Stop Weather Strip, V19476. Stile Cladding7. Mull Casing Weather Strip, V7968. Stile Weather Strip, V7809. Side Jamb Frame Cladding
When ordering replacement Ultimate Inswing French Door parts specify type of unit, part number anddescription.
ILLUSTRATIONS (not to scale)
(B)
(D)
(E)
(F)
(A)
(G)
(C)
(H)
(I)
Interior Exterior
Active Panel
(J)
(K)
(B)
(E)
(K)
Interior Exterior(A)
(G)
(H)
(J) Inactive/Dummy
Handle Assembly, Active PanelMortise lock and Multi−point lock systems(Schlage “C” keyway)Includes:1 − Interior lever (A) with 00142006 spindle, escutcheon plate
and hardware1 − Exterior lever (B) with escutcheon plate and hardware1 − Thumb turn (C) with hardware1 − Keyed cylinder (D) with housing and hardware1 − Exterior escutcheon plate gasket (E)1 − Exterior escutcheon plate (F)1 − Two piece spindle (G)2 − #10−32 x 2 1/8� Phillips ovalhead machine screws (H)1 − Interior escutcheon plate (I)1 − Thumb turn washer (J)1 − Thumb turn push nut (K)2 − Keys
Long Hinge Screw PackageIncludes:4 −#10 X 2 1/2� Screws1 − 5/32� Allen wrenchNOTE: Order Dark Bronze screw package forDark Bronze, Antique Brass and Oil RubbedBronze Hinges. Order Stainless Steel screwpackage for Silver Frost, Satin Chrome andSatin Nickel PVD Hinges .
TPGTDKBZWHSSBS PVD
118006531180063211800644118006371180063910148185
ULTIMATE INSWING FRENCH DOOR
PARTS
13.272013−12−16 11708422Marvin Parts Manual
ILLUSTRATIONNOT TO SCALE
DESCRIPTION OPER./COLOR PART NO.
Construction Lock AssemblyFor Marvin residential swinging andsliding doors with standard locks.Includes:1 − Construction Lock Cover1 − Construction Lock Hole Cover1 − Washer2 − #6−32 X 5/8� Phillips TH screws1 − #10−32 X 2� Phillips TH screw
NOTE: Replacement wood parts are supplied with connecting barb (where applicable).
TO ORDER REPLACEMENT WOOD PARTSWhen ordering replacement wood parts specify:
1. profile number;2. rough opening;3. handing;
a. on jamb parting stop specify right or left jamb (viewed from exterior)
4. length;5. finish.
ULTIMATE INSWING FRENCH DOOR
REPLACEMENT WOOD PARTS
13.342013−12−16 11708422Marvin Parts Manual
When ordering replacement aluminum parts specify:1. profile number;2. call number or rough opening;3. length;
4. LH or RH operation;5. type of product;6. finish.
ILLUSTRATIONNOT TO SCALE
DESCRIPTION
AstragalClad onlyA2047
Jamb / Head Jamb Clad Part StopClad onlyA1965
Clad Mull Casing CoverDoor and TransomA775
Mull PostClad onlyA2046
ULTIMATE INSWING FRENCH DOOR
ALUMINUM PARTS
13.352013−12−16 11708422Marvin Parts Manual
When ordering replacement aluminum parts specify:1. profile number;2. call number or rough opening;3. length;
4. LH or RH operation;5. type of product;6. finish.
ILLUSTRATIONNOT TO SCALE
DESCRIPTION
Jamb AdaptorUltimate Swinging ScreenA1958
Mull CapSwinging ScreenClad onlyA2049
Mull CapTop Hung ScreenClad onlyA2048
Jamb Z−BarUltimate Swinging ScreenA1964
Header Z−BarUltimate Swinging ScreenA1948
ULTIMATE INSWING FRENCH DOOR
ALUMINUM PARTS
13.362013−12−16 11708422Marvin Parts Manual
When ordering replacement vinyl or fiberglass parts specify:1. profile number;2. call number or rough opening;3. length;
4. LH or RH operation;5. type of product;6. finish.
ILLUSTRATIONNOT TO SCALE
DESCRIPTION
Sill 6 9/16�Beige or BronzeF2051
Sill, 4 9/16� Beige or BronzeF2050
Door SweepV2037
ULTIMATE INSWING FRENCH DOOR
VINYL AND FIBERGLASS PARTS
13.372013−12−16 11708422Marvin Parts Manual
ORDERING REPLACEMENT PANELS FOR THE ULTIMATE INSWING FRENCH DOOR ULTIMATE INSWING FRENCH DOOR 02/28/2011 − PRESENT
To order replacement panels specify:1. Indicate if for a Pre 2011 Door2. OM of panel;
NOTE: OM of panel does not include astragal or mull casing.3. active, inactive or stationary
a. Active − specify no lock (no bore), bore for passage latch/dead bolt, single−pointmortise lock (1/17/00 − Present) or multi−point lock; if multi−point; specify ordernumber or supply manufacture date. If manufacture date is before 5/10/1999,please contact your Marvin service representative.*
b. Inactive − specify head or foot bolts or multi−point lock; if multi−point; specifyorder number or supply manufacture date. If manufacture date is before5/10/1999, please contact your Marvin service representative.*
NOTE: Weather Strip is included with all panels (where applicable).
Active panels include panel drip, bored for passage/dead bolt, single−point mortise lock, or multi-point locksystem (sent without mortise lock systems; specify on order if desired).
Inactive panels include panel drip, astragal, configured for head and foot bolts or multi-point lock system.(sent without lock systems; specify on order if desired).
Stationary 1 wide panels include panel drip and sill spacer.
Stationary 2, 3 or 4 wide panels include panel drip, sill spacer and mull casing (wood only).
HEIGHT OM
WIDTH OM
Clad Active PanelExterior View
HEIGHT OM
WIDTH OM
* See Customer Service Bulletin #140
ULTIMATE INSWING FRENCH DOOR
PANEL REPLACEMENT
13.382013−12−16 11708422Marvin Parts Manual
ORDERING REPLACEMENT SLIDING SCREENS FOR ULTIMATE INSWING FRENCH DOORTop hung screens are available with aluminum surround and charcoal colored fiberglass 18 x 16 screenmesh. Aluminum mesh (ultimate screens only) is available as an option in black, charcoal, bright aluminumor bright bronze. Determine the outside measurement of the existing screen. Find the sizes that correspondto the width and height indicated on the following chart.
When ordering replacement screen specify:1. size; − If there is no existing screen from which to obtain the OM of the screen,
determine the size of the screen by using measurement conversion chart below.The daylight opening is the measurement of the visible glass.
2. with roller guide assembly or screen panel only (ultimate top hung screen)3. color;4. mesh type (if other than standard);5. handing.
Ultimate Inswing French Door 02/28/2011 to Present
Daylight Opening to OM of Sliding ScreenWood and Clad Units
Daylight Width + 10 7/32� = OM Width of ScreenDaylight Height + 13 11/16� = OM Height of Standard ScreenDaylight Height + 12 5/8� = OM Height of Ultimate Screen
NOTE: Standard screen available with fiberglass mesh and in standard sizes only. Available colors are Stone White, Bahama Brown, Bronze, Pebble Gray and Evergreen.
ULTIMATE INSWING FRENCH DOOR
SLIDING SCREENS AND SCREEN PARTS
13.392013−12−16 11708422Marvin Parts Manual
The following parts are used on Ultimate Inswing French Door 02/28/2011 to present screens Whenordering replacement parts specify quantity and part number.
ORDERING REPLACEMENT SWINGING SCREENS FOR INSWING FRENCH DOORSwinging screens are available with aluminum surround and charcoal colored fiberglass 18 x 16 screenmesh. Aluminum mesh is available as an option. Surrounds are available in bronze, white, brown, pebblegray and evergreen.
When ordering replacement screen specify:1. size; − measure the existing screen for outside measurement (OM) of the screen or use
the conversion chart below. The daylight opening is the measurement of the visible glass.2. color3. mesh type (if other than standard);4. handing (active/inactive; left/right).
Ultimate Inswing French Door 02/28/2011 to Present
Daylight Opening to OM of Swinging Screen
Wood and Clad Standard ScreenDaylight Width + 8 23/32� = OM Width of ScreenDaylight Height + 13 1/16� = OM Height of Screen
Wood and Clad Ultimate Screen (Panel)Daylight Width+ 8 1/2� = OM Width of Screen PanelDaylight Height + 12 15/16� = OM Height of Screen Panel
Wood and Clad Ultimate Screen (Insert)Daylight Width+ 5 5/8� = OM Width of Screen InsertDaylight Height + 10 1/16� = OM Height of Screen Insert
INSWING FRENCH DOOR STANDARD HINGED SCREEN PARTSThe following parts are used on Ultimate Inswing French Door standard screens 02/28/2011 to present.When ordering replacement parts specify part number, quantity and finish.
NOTE: The part numbers shown are for single−panel swinging screens. If sill sweep and cover are needed forswinging screens on a two−panel door, a quantity of 2 must be ordered.
Sherwood Green 14380480 14380481 14380482 14380483
ILLUSTRATIONNOT TO SCALE
DESCRIPTION COLOR PART NO.
Swinging Screen Hinge KitScreen to Z−BarIncludes:4 − Hinge Leafs2 − Hinge pins4 − #6 x 1/2� Phillips Pan Head screws4 − #6 x 1� Phillips Pan Head screws4 − #6 x 1 1/4� Phillips Pan Head screws
BK 05700050
Head/Foot Bolt − Inactive PanelBK 05700051
Cover Plates / Strike Plate −Inactive Panel
BK 05700052
ULTIMATE INSWING FRENCH DOOR
SWINGING SCREENS & SCREEN PARTS
W11018
SWINGING SCREEN Z−BAR KITS
When ordering replacement Z−Bar Kits specify:
1. rough opening;
2. finish.
A2049
A1950
13.462013−12−16 11708422Marvin Parts Manual
ILLUSTRATIONNOT TO SCALE
DESCRIPTION OPER./COLOR PART NO.
Handle, Interior and Exterior −Active Panel
BK 05700057
Closer Assembly − Active Panel
BK 05700053
WOOD AND ALUMINUM PARTS − SWINGING SCREEN
TO ORDER REPLACEMENT PARTSWhen ordering replacement specify:
When ordering complete screen assemblies, A2049and W11018 will need to be ordered separately.
13.472013−12−16 11708422Marvin Parts Manual
ORDERING ENERGY PANELS FOR SINGLE GLAZED WOOD ULTIMATE INSWING FRENCH DOOR
Energy panels are available for the single glazed Wood Ultimate Inswing French Doors. Aluminum surroundsare available in bronze, white, brown, pebble gray or evergreen.When ordering energy panels specify:
1. size; Determine the size of the EP by measuring the existing panel OM or use theconversion chart below. The daylight opening is the measurement of the visible glass.
2. color of surround;3. glass type;
Single glazed Wood Ultimate Inswing DoorWood Inswing French Doors manufactured 02/28/2011 to present
Handle Package, Solid BrassUltimate Inswing French Door 1993 −PresentInswing French Door 5/98 − PresentIncludes:1 − Interior locking handle assembly (A) with
10. Second Mull Casing11. First Mull Casing12. Glazing Cap, W423013. Glazing Bead, V93314. Side Jamb Parting Stop, W653515. Stationary Panel Spacer Tack
54
3
1
2
131215
14
11
10
WOOD ULTIMATE INSWING FRENCH DOOR − PRE 2011
PART IDENTIFICATION
13.572013−12−16 11708422Marvin Parts Manual
1. Head Jamb Brick Mould Casing2. Head Jamb3. Insulating Glass4. Glazing Bead (W11751)5. Sill Nose, (W12059)6. Sill7. Jamb Brick Mould Casing8. Side Jamb
WUIFDDIRECT GLAZE TRANSOM
Head Jamband Sill
Jamb
1 2
3
4
56
7
8 43
WOOD ULTIMATE INSWING FRENCH DOOR − PRE 2011
PART IDENTIFICATION
13.582013−12−16 11708422Marvin Parts Manual
NOTE: Not to scale; specifications subject to change without notice.
HEAD JAMB& SILL DETAIL
1. Head Jamb Nailing Fin/Drip Cap2. Head Jamb Cladding3. Head Jamb4. Head Jamb Parting Stop, A8365. Head Jamb Weather Strip, V7966. Head Jamb Parting Stop
Weather Strip, V7967. Top Rail Cladding8. Top Rail9. Glazing Cap, W4230
NOTE: Not to scale; specifications subject to change without notice.
HEAD JAMB& SILL DETAIL
JAMB DETAIL
CLAD ULTIMATE INSWING FRENCH DOORSTATIONARY
1. Head Jamb Nailing Fin/Drip Cap2. Head Jamb3. Head Jamb Cladding4. Head Jamb Parting Stop, A8365. Head Jamb Weather Strip, V7966. Head Jamb Parting Stop Weather
Strip, V7967. Header Spacer Tack8. Top Rail Cladding
Head or Foot Flush Bolt − InactivePanel Black 11101780
Cover Plate for Flush BoltIncludes:1 − Cover plate2 − #8 x 1� Screws Aluminum 11860402
Long Hinge Screw PackageIncludes:4 −#10 X 2 1/2� Screws1 − 5/32� Allen wrenchNOTE: Order Dark Bronze screw package forDark Bronze, Antique Brass and Oil RubbedBronze Hinges. Order Stainless Steel screwpackage for Silver Frost, Satin Chrome andSatin Nickel PVD Hinges .
TPGTDKBZWHSSBS PVD
118006531180063211800644118006371180063910148185
ULTIMATE INSWING FRENCH DOOR PRE 2011
PARTS
13.672013−12−16 11708422Marvin Parts Manual
ILLUSTRATIONNOT TO SCALE
DESCRIPTION HINGE KITCOLOR/PART NO.
INDIVIDUAL SCREWCOLOR/PART NO.
4� Butt Hinge KitIncludes:1 − 4� hinge7 − #9 x 1� Phillips flathead woodscrews1 − #10 x 2 1/2� Phillips flatheadwood screw (frame)
NOTE: Hinge part number includes the color matched screws. If you need to order the screwsseparately, they are listed below aligned with the corresponding hinge color.
SCREWDESCRIPTION
HINGE KITCOLOR/HANDING/PART NO.
INDIVIDUAL SCREWCOLOR/PART NO.
LH RH
#10x2 1/2�Phillips flathead wood screws(jamb). Quantity of one needed per hinge.
ORDERING REPLACEMENT VINYL, ALUMINUM OR FIBERGLASS PARTS FOR THE ULTIMATE INSWING FRENCH DOORPlease reference the Aluminum Chapter (located online only)for select and standard color part numbers.
ORDERING REPLACEMENT PANELS FOR THE ULTIMATE INSWING FRENCH DOOR ULTIMATE INSWING FRENCH DOOR 1993 − PRESENTINSWING FRENCH DOOR 1998 − 2005
To order replacement panels specify:1. OM of panel;
NOTE: OM of panel does not include astragal or mull casing.2. active, inactive or stationary
a. Active − specify no lock (no bore), bore for passage latch/dead bolt, single−pointmortise lock (1/17/00 − Present) or multi−point lock; if multi−point; specify ordernumber or supply manufacture date. If manufacture date is before 5/10/1999,please contact your Marvin service representative.*
b. Inactive − specify head or foot bolts or multi−point lock; if multi−point; specifyorder number or supply manufacture date. If manufacture date is before5/10/1999, please contact your Marvin service representative.*
NOTE: Weather Strip is included with all panels (where applicable).
Active panels include panel drip, bored for passage/dead bolt, single−point mortise lock, or multi-point locksystem (sent without mortise lock systems; specify on order if desired).
Inactive panels include panel drip, astragal, configured for head and foot bolts or multi-point lock system.(sent without lock systems; specify on order if desired).
Stationary 1 wide panels include panel drip and sill spacer.
Stationary 2, 3 or 4 wide panels include panel drip, sill spacer and mull casing (wood only).
HEIGHT OM
WIDTH OM
Clad Active PanelExterior View
HEIGHT OM
WIDTH OM
* See Customer Service Bulletin #140
ULTIMATE INSWING FRENCH DOOR PRE 2011
PANEL REPLACEMENT
13.762013−12−16 11708422Marvin Parts Manual
INSWING FRENCH DOOR WEATHER STRIP ULTIMATE INSWING FRENCH DOOR 1993 − PRESENTINSWING FRENCH DOOR 1998 − 2005
When ordering replacement weather strip specify:1. quantity;2. length;3. part number;4. description.
Connecting BarbV803NOTE: Color may varydepending on current stock.
Wood Door and Wood andClad Transom only
SpecifyLength
15812999
Inactive Panel Stile CenterV780
150�150�
BGBK
1517409915174098
ULTIMATE INSWING FRENCH DOOR PRE 2011
WEATHER STRIP
13.772013−12−16 11708422Marvin Parts Manual
ORDERING REPLACEMENT SLIDING SCREENS FOR ULTIMATE INSWING FRENCH DOORTop hung screens are available with aluminum surround and charcoal colored fiberglass 18 x 16 screenmesh. Aluminum mesh (ultimate screens only) is available as an option in black, charcoal, bright aluminumor bright bronze. Determine the outside measurement of the existing screen. Find the sizes that correspondto the width and height indicated on the following chart.
When ordering replacement screen specify:1. size; − If there is no existing screen from which to obtain the OM of the screen,
determine the size of the screen by using measurement conversion chart below.The daylight opening is the measurement of the visible glass.
2. with roller guide assembly or screen panel only (ultimate top hung screen)3. color;4. mesh type (if other than standard);5. handing.
NOTE: On April 1, 1993 rollers, guide bars and screen width was reduced 3/8�.Replacement Screens (for units manufactured prior to April 1993) will be sent with anew roller bar for compatibility.
* 8/0 Height change March 4, 2002
Daylight Opening to OM of Sliding ScreenWood and Clad Units
Daylight Width + 10 7/32� = OM Width of ScreenDaylight Height + 12 15/16� = OM Height of Screen
ULTIMATE INSWING FRENCH DOOR 1993 − FEBRUARY 28, 2011INSWING FRENCH DOOR 1998 − 2005
ULTIMATE INSWING FRENCH DOOR PRE 2011
SLIDING SCREENS AND SCREEN PARTS
13.782013−12−16 11708422Marvin Parts Manual
The following parts are used on Ultimate Inswing French Door (1993 − present) and on Inswing FrenchDoor (5/98 − 2005) screens. When ordering replacement parts specify:
ORDERING REPLACEMENT HINGED SCREENS FOR INSWING FRENCH DOORHinged screens are available with aluminum surround and charcoal colored fiberglass 18 x 16 screenmesh. Aluminum mesh is available as an option. Determine the outside measurement of the existingscreen. Find the sizes that correspond to the width and height indicated on the following chart. Surroundsare available in bronze, white, brown, pebble gray and evergreen.
When ordering replacement screen specify:1. size; − If there is no existing screen from which to obtain the OM of the screen,
determine the size of the screen by using measurement conversion chart below.The daylight opening is the measurement of the visible glass.
2. color;3. mesh type (if other than standard);4. handing (active/inactive; left/right).
Standard Screen Width Standard Screen HeightCN Width OM Width CN Height OM Height
Closer AssemblyUltimate Screen/ComboIncludes:1 − Closer (A)1 − Jamb Bracket (B)1 − Door Bracket (C)1 − Head Jamb Bracket (D)
BK 18900608
Flush BoltUltimate Screen/Combo
18900610
Exterior Interior
Handle AssemblyUltimate Screen/ComboInterior and Exterior handles
* Exterior handle color. Interior handle color isalways black.
TP*BS PVD* SN PVD*BZ PVD*
18900600189006011890060218900603
ULTIMATE INSWING FRENCH DOOR PRE 2011
HINGED SCREENS & SCREEN PARTS
13.832013−12−16 11708422Marvin Parts Manual
INSWING FRENCH DOOR STANDARD HINGED SCREEN PARTSThe following parts are used on Ultimate Inswing French Door (5/98 − present) and on Inswing FrenchDoor (5/98 − 2005) screens. When ordering replacement parts specify:
1. part number;2. quantity;3. finish.
NOTE: The part numbers shown are for single−panel swinging screens. If sill sweep and cover are needed forswinging screens on a two−panel door, a quantity of 2 will need to be ordered.
Swinging Screen Hinge KitScreen to Z−BarIncludes:4 − Hinge Leafs2 − Hinge pins4 − #6 x 1/2� Phillips Pan Head screws4 − #6 x 1� Phillips Pan Head screws4 − #6 x 1 1/4� Phillips Pan Head screws
TO ORDER REPLACEMENT PARTSWhen ordering replacement specify:
1. length;2. finish.
ProfileNumber
Mull Cap Hinged Screen A340
Hinged Screen Mull Casing W1075
When ordering complete screen assemblies, A340and W1075 will need to be ordered separately.
13.862013−12−16 11708422Marvin Parts Manual
ORDERING ENERGY PANELS FOR SINGLE GLAZED WOOD ULTIMATE INSWING FRENCH DOOR
If you are replacing an existing energy panel, determine the outside measurement of the existing energypanel. Find the sizes that correspond to the width and height indicated on the following chart. Energy panelsare available for the single glazed Wood Ultimate Inswing French Doors. Aluminum surrounds are availablein bronze, white, brown, pebble gray or evergreen.When ordering energy panels specify:
1. size; If there is no existing EP from which to obtain the OM of the panel, determine thesize of the EP by using the conversion chart below. The daylight opening is themeasurement of the visible glass.
2. color of surround;3. glass type;
Single Glazed Wood Ultimate InswingWood Inswing French Doors manufactured 5/98 − 2005
Daylight Opening to OM of EPDaylight Width + 1 3/8� = OM Width of EPDaylight Height + 1 3/8� = OM Height of EP
ENERGY PANEL PARTSEnergy panels are attached with turn buttons. Turn button styles may vary depending on current stock.You will receive the most current style in the color of your choice.
When ordering energy panels parts specify:1. quantity;2. description;3. color;4. part number.
ILLUSTRATIONNOT TO SCALE
DESCRIPTION COLOR PART NUMBER
Turn ButtonPackages of 50 include#8x3/4� SS full thread screws(11808340).
If ordering by “each”, screwsmust be ordered separately.
SW
CL
PB
BZ
BN
Each
11869294
11869309
11869292
11869291
11869293
Pkg of 50
11869314
11869315
11869312
11869311
11869313
WOOD ULTIMATE INSWING FRENCH DOORS PRE 2011
ENERGY PANELS AND PARTS
13.872013−12−16 11708422Marvin Parts Manual
WOOD ULTIMATE INSWING FRENCH DOOR COMBINATION DOOR PARTS 1993 − PRESENTWOOD INSWING FRENCH DOOR 5/98 − 2005
When ordering replacement combination parts specify:1. part number;2. quantity;3. description.
Handle Package, Solid BrassUltimate Inswing French Door 1993 −PresentInswing French Door 5/98 − PresentIncludes:1 − Interior locking handle assembly (A) with
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE − PARTS
13.922013−12−16 11708422Marvin Parts Manual
ILLUSTRATIONNOT TO SCALE
DESCRIPTION
Dim. A
Inactive Panel Locking Rod, Top or Bottom For Head or FootBoltIFD − std. UIFD − std. 1997* − 5/10/99Solid stainless steel rod with 1/4� − 20 threadsIncludes:1 − Locking rod (includes shootbolt)
Height Top LockingRod Length
CN 6−5 ht 9 11/16� Replace with PN 05700180CN 6−8 ht 9 11/16� Replace with PN 05700180CN 7−0 ht 9 11/16� Replace with PN 05700180CN 8−0 ht 27 1/32� Replace with PN 05700185
Height Bottom Locking Rod Length
CN 6−5 ht 9 11/16� Replace with PN 05700180CN 6−8 ht 9 11/16� Replace with PN 05700180CN 7−0 ht 9 11/16� Replace with PN 05700180CN 8−0 ht 9 11/16� Replace with PN 05700180
Locking Rod, Top for Multi−PointIFD − opt.* UIFD − std. 1997* − 5/10/99 (Trimco)Solid stainless steel rod with 1/4� − 20 threads1 − Locking rod (includes shootbolt)
Height Top Locking Rod Length
CN 6−5 ht 35 3/4� CN 6−8 ht 39 1/32� These parts may be fabricatedCN 7−0 ht 43 1/32� using PN 05700190CN 8−0 ht 55 1/32�
Locking Rod, Bottom for Multi−Point LockIFD − opt.* UIFD − std. 1997* − 5/10/99 (Trimco)Solid stainless steel rod with 1/4� − 20 threads1 − Locking rod (includes shootbolt)
Backset Extension for Head or Foot BoltUltimate Inswing French Door 1993 −1997*with #10−24 threadsIncludes:1 − Backset extension1 − #10−24x3/4� Phillips flathead machine
screw
Checkavailability16152010
3 1/2� Hinge PairInswing French Door 1985 − 5/98Inswing Terrace Door 1982 − 5/98
Brass Plated
Solid Brass
SS
NA
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
Multi−Point Mortise Lock, ActiveUltimate Inswing French Door1993−1997* (Trimco)#10−24 threads for locking rodsReplaced with lock, rods and end boltused from 1997 − 5/10/99.
NA
Multi−Point Mortise Lock, InactiveUltimate Inswing French Door1993−1997* (Trimco)#10−24 threads for locking rodsReplaced with lock, rods and end boltused from 1997 − 5/10/99.
NA
* See product history for details.
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE − PARTS
13.992013−12−16 11708422Marvin Parts Manual
ILLUSTRATIONNOT TO SCALE
DESCRIPTION OPER./COLOR PART NO.
End Bolt for Head/Foot BoltInswing French Door before 5/98
NA
Head or Foot bolt Strike PlateInswing French Door before 5/98
Solid Brass
Polished Chrome
Brushed Chrome
N/A
N/A
N/A
Head or Foot bolt Guide PlateInswing French Door before 5/98
YZD NA
Multi-Point Handle, Active, SolidBrass (Essve)Inswing French Door before 5/98Inswing Terrace Door 1990 − 5/98(Weiser keyway)
Can use current handleby turning the current handle upside down.
Multi-Point Handle, Inactive, Solid Brass (Essve)Inswing French Door before 5/98Inswing Terrace Door 1990 − 5/98
* See product history for details.
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE − PARTS
13.1002013−12−16 11708422Marvin Parts Manual
ILLUSTRATIONNOT TO SCALE
DESCRIPTION OPER./COLOR PART NO.
Spindle Package for Multi-PointHandle (Essve)Inswing French Door before 5/98Inswing Terrace Door 1990 − 5/98
NA
Active Multi−Point HardwareAssembly (Essve)Inswing French Door before 5/98Inswing Terrace Door 1990 − 5/98
NA
Inactive Multi-Point HardwareAssembly (Essve)Inswing French Door before 5/98
NA
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE − PARTS
13.1012013−12−16 11708422Marvin Parts Manual
ILLUSTRATIONNOT TO SCALE
DESCRIPTION OPER./COLOR PART NO.
Multi-Point Top Corner DriveInswing French Door before 5/98(Essve)For Inactive panel with multi−pointIncludes:1 − Top corner drive
Attached with #6x1/2� Phillips flathead wood screws
Multi-Point Bottom Corner DriveInswing French Door before 5/98(Essve)For Inactive panel with multi−point
4 13/32� (112)
NA
Multi-Point Corner Drive FillerInswing French Door before 5/98(Essve)
NA
Multi-Point Lock Jamb Strike,Center, Solid Brass (Essve)Inswing French Door before 5/98Inswing Terrace Door 1990 − 5/98Includes:1 − Jamb strike4 − #7 x 5/8� Phillips flathead wood screws
NA
Multi-Point Lock Jamb Strike,Center, Extended, Solid Brass(Essve)Inswing French Door before 5/98Inswing Terrace Door 1990 − 5/98
NA
Multi-Point Lock Jamb Strike, Top orBottom, Solid Brass (Essve)Inswing French Door before 5/98Inswing Terrace Door 1990 − 5/98
NA
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE − PARTS
13.1022013−12−16 11708422Marvin Parts Manual
ILLUSTRATIONNOT TO SCALE
DESCRIPTION OPER./COLOR PART NO.
Multi-Point Lock Strike, InactivePanel, Head Jamb (Essve) Inswing French Door before 5/98
NA
Multi-Point Lock Corner Drive SillReceptacle, Solid Brass (Essve)Inswing French Door before 5/98
NA
Sill Receptacle Gasket (Essve)Inswing French Door before 5/98 NA
Astragal Strike Latch (Essve)Inswing French Door before 5/98Inactive panel with multi-point hardwareIncludes:1 − Latch2 − #7x5/8� Phillips flathead wood screws
NA
Filler Foam, Weep/DrainUltimate Inswing French Door 1996−1998 NA
Foam Plug, Clad Part StopUltimate Inswing French Door 1996−1998 NA
Lever Washers − Pre − 2000NA
Lever Spacers − Pre − 2000NA
Lever Shims − Pre − 2000NA
Dummy Lever Cams − Pre − 2000
NA
Snap Rings − Pre − 2000
NA
Spindle − Pre − 2000FD − opt.* UFD − std.4 3/16�
NA
Stop clip with screws 00142016(Check foravailability)
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
Head Jamb and Jamb Parting Stop (4 9/16� Jambs) W7500 − − −
Sill Liner (oak) W7550 W7550
Threshold (oak) W7551 W7551
Screen Track Filler W5221 − − −
Head Jamb and Jamb Parting Stop (6 9/16� Jambs) W7524 − − −
Stationary Panel Cover W7553 − − −
Head Jamb, Jamb and Panel Spacer W7555 − − −
INSWING FRENCH (BEFORE 5/98)Wood Clad
Astragal W7222 W7230
Astragal (Multi−Point) W7231 W7219
Operator First Mull Casing W1092 − − −
Second Mull Casing W1084 − − −
Stationary Head Jamb, Jamb and Astragal Filler NA − − −
Stationary Head Jamb and Jamb Spacer NA NA
INSWING TERRACE DOOR (BEFORE 5/98)Wood Clad
Stationary Head Jamb and Stationary Jamb Filler NA NA
Stationary Head Jamb and Stationary Jamb Spacer NA NA
Operator First Mull Casing W1092 − − −
Stationary First Mull Casing W1090 − − −
Second Mull Casing W1084 − − −
Third Mull Casing W1080 − − −
TO ORDER REPLACEMENT WOOD PARTSNOTE: All obsolete parts subject to availability.When ordering replacement wood parts specify:
1. profile number;2. call number or rough opening;3. handing;
a. on jamb parting stop specify right or left jamb (viewed from exterior)b. for operator first mull casing specify right or left hand (as viewed from the exterior)c. for astragal specify hardware prep (if applicable)
4. length;5. finish.6. handing;
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE REPLACEMENT WOOD PARTS
A641*
V799*
V302
A704 A706
F-251*
A718*
F-253*
V199
A719*
A756*A774* V857* A740* V787/F300*
F254*V788/F301* F255*
13.1082013−12−16 11708422Marvin Parts Manual
ORDERING REPLACEMENT VINYL, ALUMINUM OR FIBERGLASS PARTS FOR THE INSWING FRENCH DOORFRENCH INSWING (BEFORE 5/98)
Wood Clad
Stationary and Sidelite Leveling Block − Beige V199 V199
Sweep − Beige V302 V302
Operator Center Mull (with plug) − − − A704
Operator Center Mull Base − − − A706
2� Clad Frame Extension A718*
Astragal Cladding A719*
Ultrex Sill (4 9/16� Jambs) − Beige F251* F251*
Ultrex Sill (6 9/16� Jambs) − Beige F253* F253*
ULTIMATE INSWING FRENCH DOOR (1993 − 1998)
Wood Clad
Mullion Casing, 6 9/16� Jambs − − − A774*
Head Jamb, Jamb Parting Stop − − − A756*
Stationary Panel Sill Spacer V857* V857*
Hydro-Optimizer − Beige (replaced with A1251) A740* A740*
Panel Drip − Beige F305* F305*
Sill Cover and Ultrex Sill Core Assembly, 4 9/16� JambsBeige (includes Hydro-Optimizer, threshold and sill liner) V787/F300* − − −
Sill Cover and Ultrex Sill Core Assembly 6 9/16� JambsBeige (includes Hydro-Optimizer, threshold and sill liner) V788/F301* − − −
OBSOLETE REPLACEMENT VINYL, ALUMINUM OR FIBERGLASS PARTS FOR THE INSWING TERRACE DOOR MANUFACTURED 1982 − 5/98INSWING TERRACE DOOR (1982 − 1998)
Clad Wood
Stationary and Sidelite Leveling Block V199 V199
Screen Channel(V253 no longer available in Brown)
− − − V253 (PB)
− − − V310
Sweep V302 V302
Operator Center Mull (with plug) A704 − − −
Operator Center Mull and Screen Mull Base A706 − − −
Operator Screen Mull (with plug) A705* − − −
Stationary Center Mull (with plug) A707* − − −
Stationary Center Mull Base A708* − − −
Sill Overlay A702* A702*
Ultrex Sill − Beige F251* F251*
* No longer available (shaded).
TO ORDER REPLACEMENT PARTSNOTE: All obsolete parts subject to availability.When ordering replacement parts specify:
1. profile number;2. size (call number or rough opening);3. length;4. handing;5. finish.
INSWING TERRACE DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE REPLACEMENT PARTS
Wood InswingActive PanelExterior View
HEIGHT OM
WIDTH OM
HEIGHT OM
WIDTH OM
Clad InswingActive Panel Exterior View
Active panels include: sweep and route for hinges.Inactive panels include: sweep, route for hinges, astragal and head and footbolts.Stationary panels include: leveling block.
1. size (call number or OM of panel);
2. active, inactive or stationary;a. specify bore or no bore
3. handing;
4. glazing;
5. finish.
6. panel styleNote: Clad French Door started eased edge design March 4,1996 and Wood French Door started eased edge design April15, 1996.
13.1102013−12−16 11708422Marvin Parts Manual
ORDERING REPLACEMENT PANELS FOR THE OBSOLETE WOOD AND CLAD INSWINGFRENCH DOOR (MANUFACTURED BEFORE 5/98)
To order replacement panels specify:
CLAD AND WOOD FRENCH DOOR (PRE 1998)CN Panel OSM Panel DLO
Width Height Width Height
2068 / 4068 24� 80� 14 1/2� 67 1/8�
2668 / 5068 30� 80� 20 1/2� 67 1/8�
2868 / 5668 32� 80� 22 1/2� 67 1/8�
3068 / 6068 36� 80� 26 1/2� 67 1/8�
2665 27 5/8� 76 5/16� 18 1/2� 63 7/16�
3065 33 5/8� 76 5/16� 24 1/8� 63 7/16�
7/0 Height 84� 67 1/8�
8/0 Height 96� 80 7/8�
Units will have:4 3/4� top rail and stile. Bottom rail height: 6/5 and 6/8 = 8 1/8�; 7/0 = 12 1/8�; and 8/0 = 10 3/8�.3 1/2� x 3 1/2� butt hinges. 6/5, 6/8, 7/0 heights will have 4 hinges. 8/0 height will have 5 hinges.
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE PANEL REPLACEMENT
1. size (call number or OM of panel);
2. active, inactive or stationary;a. specify bore or no bore
3. handing;
4. panel style; eased edge stile/rail joints orflushed sandedClad French Door started eased edge design March 4, 1996 and
Wood French Door started eased edge design April 15, 1996.
5. glazing;
6. finish.
NOTE: Panels feature no bore (standard). Operating panels include sweep.Stationary panels include leveling block.
HEIGHT OM
WIDTH OM
HEIGHT OM
WIDTH OM
Wood Operating PanelExterior View
Clad Operating PanelExterior View
13.1112013−12−16 11708422Marvin Parts Manual
ORDERING REPLACEMENT PANELS FOR THE OBSOLETE WOOD AND CLAD INSWINGTERRACE DOOR (MANUFACTURED 1982 − 5/98)
To order replacement panels specify:
CLAD AND WOOD TERRACE DOOR (PRE 1998)CN Panel OSM Panel DLO
Width Height Width Height
2065 24� 76 5/8� 14 1/2� 67 1/8�
2665 30 13/16� 76 5/8� 21 5/16� 67 1/8�
2865 33 1/4� 76 5/8� 23 3/4� 67 1/8�
3065 36 13/16� 76 5/8� 27 5/16� 67 1/8�
4065 21 13/16� 76 5/8� 14 1/2� 67 1/8�
5065 28 5/8� 76 5/8� 21 5/16� 67 1/8�
5665 31 13/16� 76 5/8� 23 3/4� 67 1/8�
6065 34 5/8� 76 5/8� 27 5/16� 67 1/8�
8/0 Height 93 1/8� 83 5/8�
Units will have:� 4 3/4� top rail and stile. Bottom rails: (1) 2 9/16� and (1) 4 3/4� stile used on every panel of 2 and 3 wide units,
except for XOO and OOX configurations where the center panel will have (2) 2 9/16� stiles.� 3 1/2� x 3 1/2� butt hinges. 6/5 height will have 4 hinges. 8/0 height will have 5 hinges.� All single units will have 4 3/4� stiles and top and bottom rails.� Sidelites units will have 4 3/4� top and bottom rails and 2 9/16� rails and 2 9/16� stiles.
WOOD AND CLAD TERRACE DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE PANEL REPLACEMENT
13.1122013−12−16 11708422Marvin Parts Manual
ORDERING REPLACEMENT SLIDING SCREENS FOR INSWING FRENCH DOORTop hung screens are available with aluminum surround and charcoal colored fiberglass 18 x 16 screenmesh. Aluminum mesh is available as an option in black, charcoal, bright aluminum or bright bronze. Surrounds are available in bronze, white, brown, pebble gray and evergreen.
When ordering replacement screen specify:1. size; Measure the OM of the existing screen or use the conversion chart below
to determine the size. The daylight opening is the measurement of the visibleglass
2. color;3. mesh type (if other than standard);4. handing.
NOTE: On April 1, 1993 rollers, guide bars and screen width was reduced 3/8�.Replacement Screens (for units manufactured prior to April 1993) will be sent with anew roller bar for compatibility.
Daylight Opening to OM of Sliding ScreenWood and Clad Units
Daylight Width + 10 7/32� = OM Width of ScreenDaylight Height + 12 15/16� = OM Height of Screen
INSWING FRENCH DOOR 1998 − 3/3/02ULTIMATE INSWING FRENCH DOOR 1993 − 3/3/02
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
WOOD INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE PARTS − SCREENS AND SCREEN PARTS
13.1142013−12−16 11708422Marvin Parts Manual
The following parts are used on the top hung sliding screens. When ordering replacement parts specifyquantity and part number.
ILLUSTRATIONNOT TO SCALE
DESCRIPTION OPER./COLOR PART NO.
Automatic Screen Door CloserAssemblyUsed until 1/31/00
Wood and Clad Ultimate Inswing FrenchDoor manufactured 5/98 − PresentWood and Clad Ultimate Inswing FrenchDoor manufactured 1993 − Present
NA
Astragal
CN 80 92 15/16� SWBZPBBNEG
NANANANANA
WOOD INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE PARTS − SCREENS AND SCREEN PARTS
13.1152013−12−16 11708422Marvin Parts Manual
ORDERING REPLACEMENT HINGED SCREENS FOR INSWING FRENCH DOORHinged screens are available with aluminum surround and charcoal colored fiberglass 18 x 16 screenmesh. Aluminum mesh is available as an option. Surrounds are available in bronze, white, brown, pebblegray and evergreen.
When ordering replacement screen specify:1. size; − Measure the OM of the existing screen or use the conversion chart
below to determine the size. The daylight opening is the measurement of thevisible glass
2. color;3. mesh type (if other than standard);4. handing (active/inactive; left/right).
Daylight Opening to OM of Hinged ScreenWood and Clad Units
Daylight Width + 8 11/16� = OM Width of ScreenDaylight Height + 9 3/8� = OM Height of Screen
INSWING FRENCH DOOR 1999 − 3/3/02ULTIMATE INSWING FRENCH DOOR 1999 − 3/3/02
INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE − HINGED SCREENS & PARTS
13.1162013−12−16 11708422Marvin Parts Manual
ORDERING REPLACEMENT SCREENS FOR OBSOLETE WOOD AND CLAD TERRACE DOOR
NOTE: Replacement screens for your Terrace door may be available. Contact your Marvin representative.
When ordering replacement screens you will need to have the following information available:1. size; Measure the OM of the existing screen or use the conversion chart below
to determine the size. The daylight opening is the measurement of the visibleglass
2. color;3. mesh type (if other than standard);4. handing.
Wood and Clad Terrace DoorWood units manufactured 1982 − 5/98Clad units manufactured 1986 − 5/98
Daylight Opening to OM of Screen
Daylight Width + 8 3/16� = OM Width of ScreenDaylight Height + 10 3/4� = OM Height of Screen
WOOD AND CLAD TERRACE DOOR
OBSOLETE SCREEN DOOR SIZING CHART
13.1172013−12−16 11708422Marvin Parts Manual
WOOD AND CLAD TERRACE DOOR MANUFACTURED 1982 − 5/98
The following parts are used on the Terrace Door screens. When ordering replacement parts specify:1. part number;2. quantity.
ILLUSTRATIONNOT TO SCALE
DESCRIPTION OPER./COLOR PART NO.
Pile Weather Strip, Screen17/64� x 29/64�Specify Length BG 11107533
Interior Handle AssemblyNA
Strike Hardware PackageNA
StrikeNA
Screen Roller (with gear)Used 1989 − 5/98 NA
WOOD AND CLAD TERRACE DOOR
OBSOLETE PARTS − SCREENS AND SCREEN PARTS
13.1182013−12−16 11708422Marvin Parts Manual
TERRACE DOOR SCREEN PARTS
NOTE: Replacement screens for the Terrace door may be available. Contact your Marvin representative.
1984 − 1989ILLUSTRATION
NOT TO SCALEDESCRIPTION OPER./COLOR PART NO.
Roller Assembly NA
Roller Adjustment ScrewNA
1983 − 1984ILLUSTRATION
NOT TO SCALEDESCRIPTION OPER./COLOR PART NO.
Roller Assembly NA
1983ILLUSTRATION
NOT TO SCALEDESCRIPTION OPER./COLOR PART NO.
Roller Assembly NA
WOOD AND CLAD TERRACE DOOR
DISCONTINUED SCREEN PARTS
13.1192013−12−16 11708422Marvin Parts Manual
ORDERING ENERGY PANELS FOR OBSOLETE SINGLE GLAZED WOOD ULTIMATE INSWING FRENCH DOORS Energy panels are available for the single glazed Wood Ultimate Inswing French Door. Aluminum surroundsare available in bronze, white, brown or pebble gray.
When ordering energy panels specify:
1. size; Measure the OM of the existing panel or use the conversion chart below to determinethe size. The daylight opening is the measurement of the visible glass
2. color of surround;3. glass type.
Wood Ultimate Inswing French Door
Wood Ultimate Inswing French Doors manufactured 1985 −5/98
Daylight Opening to OM of EP
Daylight Width + 1� = OM Width of EPDaylight Height + 1� = OM Height of EP
Daylight Width + 1� = OM Width of EPDaylight Height + 1� = OM Height of EP
ENERGY PANEL PARTSEnergy panels are attached with the current style turn buttons. Discontinued black turn buttons have beenreplaced by brown
WOOD TERRACE DOOR
ENERGY PANELS AND PARTS
13.1212013−12−16 11708422Marvin Parts Manual
ORDERING ENERGY PANELS FOR SINGLE GLAZED WOOD INSWING FRENCH DOOR
Energy panels are available for the single glazed Wood Ultimate Inswing French Doors. Aluminum surroundsare available in bronze, white, brown, pebble gray or evergreen.When ordering energy panels specify:
1. size; Measure the OM of the existing panel or use the conversion chart below to determinethe size. The daylight opening is the measurement of the visible glass
2. color of surround;3. glass type;
Single Glazed Wood Ultimate InswingWood Ultimate Inswing French Doors manufactured 5/98 − 3/3/02
Daylight Opening to OM of EP
Daylight Width + 1 3/8� = OM Width of EPDaylight Height + 1 3/8� = OM Height of EP
ORDERING REPLACEMENT WOOD, VINYL OR ALUMINUM PARTS FOR THE WOOD INSWING AND FRENCH DOOR MANUFACTURED 1991 − 5/98 ULTIMATE INSWING FRENCH DOOR 1993 − 5/98
ALUMINUM PARTSWood Ultimate Inswing French Door Rectangular Panels
ProfileNumber
Drip Cap A102*
* No longer available (shaded).
TO ORDER REPLACEMENT PARTSWhen ordering replacement combination door wood, vinyl or aluminum parts specify:
1. profile number;2. size (call number or rough opening);3. length;4. finish.
WOOD INSWING FRENCH DOOR / ULTIMATE INSWING FRENCH DOOR
OBSOLETE REPLACEMENT PARTS − COMBINATION DOOR
W6126 − Stationary PanelHead Jamb Spacer*
W6248 − Mull Filler* A102 − Drip Cap*
1(25)
1/8(3)
7/32(6)
1 3/4(44)
13.1242013−12−16 11708422Marvin Parts Manual
ORDERING REPLACEMENT WOOD, VINYL OR ALUMINUM PARTS FOR THE WOOD TERRACE COMBINATION DOOR MANUFACTURED 1982 − 5/98
WOOD PARTSProfile
Number
Stationary Panel Head Jamb Spacer W6126*
Mull Filler W6248*
ALUMINUM PARTSProfile
Number
Drip Cap A102*
* No longer available (shaded).
TO ORDER REPLACEMENT PARTS
When ordering replacement combination wood, vinyl or aluminum parts specify:1. profile number;2. size (call number or rough opening);3. length;4. finish.