HAZARDOUS LOCATIONS TELEMETRY EQUIPMENT & WIRELESS SYSTEMS ACCESSORIES
HAZARDOUS LOCATIONSTELEMETRY EQUIPMENT
&WIRELESSSYSTEMSACCESSORIES
3
APPROVALS
COMPANY
Our product range is totally designed and manufactured according to the stringent specifications of both European and North American standards.
Our technical department works with highly sophisticated systems, which include state-of-the-art 3D design software, finite element analysis, vector network analyzers, and other electronic equipment.
The italian Solexy headquarter in Desenzano del Garda (Brescia) and the USA R&D department, located in Cincinnati (Ohio)
SOLEXY specializes in devices and patented technology for radio and buss transmissions in hazardous classified areas such as refineries, chemical plants, mines, off shore rigs and other hazardous rated areas.
Our flameproof intrinsically safe barriers for radios and busses allowed transmission of RF signals into classified “Hazardous Areas”.
Expanding on the need of this technology in industrial environments, we developed a line of industrial antennas that meet the demanding requirements and hostility of the process environment. Expanding our patented technology and realizing the demand to protect other signals, we developed a solution for Ethernet. It is now possible to transmit Ethernet signals from explosion proof enclosures or purge panel systems into a hazardous area with the use of our Passive Ethernet barrier, without the cost of additional sealing devices, area rated conduit systems, or additional power.
5
HAZARDOUS AREAWIRELESS SYSTEMS CATAGLOGUE
Hazardous area wireless systems 7Explosion proof WiFi access point 8
Explosion proof WiFi MIMO access point 10
Explosion proof router WiFi access point 12
Explosion proof bluetooth serial adapter 14
Explosion proof VHF & UHF radiomodems 16
Explosion proof modbus RTU radiomodems 18
Explosion proof ethernet radiomodems 20
Explosion proof RF junction box 22
Accessories 25Heavy duty antennas and cables
Dipole ANH series 26
J-Pole ANH series 28
Flexible ANF series 30
GPS ANH series 32
Coax cable extension 34
Dimensional drawings 37
WS and WA series hazardous area enclosures are available as Junction boxes, Wi-Fi hotspots configured as a master,
client or repeater, Radio Modems that can be used to interface remote serial ports and
digital and analog I/O from the field to remote locations and totally wire free transmission of RF signals.
Optional intrinsically safe ethernet signalscan be added with minimal cost of installation.
Radio modems with remote I/O can transmit and receive using Modbus protocol as a standard option
or can be transparent.Available in either a stainless steel (WS) or powder coated
aluminum (WA) explosion proof rated enclosure.
Explosion proof Ex d IIC enclosure made in alluminum (WA series) or stainless steel (WS series) weather proof IP66/68
All Approved for ATEX, IECEx and UL.
7
Hazardous area wireless systems
Data contained in this specification are subject to change without notice8
HAZARDOUS AREA WIRELESS SYSTEMS
The Solexy WA/WSA01 is the smallest and most powerful WiFi access point (AP) rated for installation in hazardous locations and harsh environments. Completely configurable through its Ethernet or WiFi port via your internet browser without the need of installing any software or driver for the device.
The WA/WSA01 provides three different operating functions: AP, WiFi client and/or WDS repeater. It can be powered using the same Ethernet cable used for data or independently.
With Solexy’s WA and WS enclosures and their rugged construction water proof IP66 and IP68 combined with Atex and IECEx certificates, Solexy offers a wireless device solution for installation in classified Ex areas (gas, dust and mining) and harsh environments, including temporary submersion.
FEATURESOPERATING FUNCTIONS WiFi Access Point, WiFi Client, Repeater
WIFI 802.11 b/g/n
ETHERNET CONNECTION Terminal strip or optional RJ45 connector. On request the unit can be supply complete of Solexy Ethernet barrier BX series.
HEAVY DUTY CONSTRUCTION Explosion proof Ex d IIC enclosure made of alluminum (WA series) or stainless steel (WS series) weather proof IP66/68.
B00
015-
00
EXPLOSION PROOF WIFI ACCESS POINT
APPROVALSATEX / IECEX CERTIFICATION II 2G Ex db IIC T5-T4 Gb II 2D Ex tb IIIC T110°C/T140°C Db I M2 Ex db I Mb (WS only)
ANTENNAS: ANF72 series flexible dipole (2 dBi) ANH73 series heavy duty J-Pole (4.35 dBi)
MOUNTING BRACKET: PM400-0001-00 Universal mounting kit for wall and pole installation
AVAILABLE ACCESSORIES
Dimensional drawings at page 37
Data contained in this specification are subject to change without notice 9
NOMENCLATURE
a Enclosure WA Aluminum polyester powder coated WS Stainless steel AISI 316 (CF8M) electropolish
b Antenna coupler (1)
03 n° 1 AXN series (N Female) 04 n° 1 AXF series (RP-SMA Female)
c Cable entrie 42 n° 4 3/4” npt-f (one used for antenna coupler) 44 n° 4 M25x1.5 (one used for antenna coupler)
d Approvals X1 IECEx and ATEX Gas and Dust (WA only) X2 IECEx and ATEX Gas, Dust and Mining (WS only)
(1) Antenna not included.
S WA A01 10 - 42 0 X1a b c d
SPECIFICATIONS
GENERAL
Power supply 15V, 0,8A (min 12VDC - max 24VDC)
Power method Passive Power over Ethernet cable (2 twists used for data, 2 twists used for power) or through dedicated terminal strip (external power supply required).A POE power supplier to be installed in safe area is included.
Max power consumption 8W
Operating frequency 2412 - 2462 MHz
Output power 28 dBm
WiFi protocoll TX Power specification RX Power specification
Data Rate/MCS Avg. Tx Data Rate/MCS
Sensitivity
11 b/g 1-24 Mbps 28 dBm 1-24 Mbps -97 dBm
36 Mbps 27 dBm 36 Mbps -80 dBm
48 Mbps 26 dBm 48 Mbps -77 dBm
54 Mbps 24 dBm 54 Mbps -75 dBm
11 n MCS0 28 dBm MCS0 -96 dBm
MCS1 28 dBm MCS1 -95 dBm
MCS2 28 dBm MCS2 -92 dBm
MCS3 28 dBm MCS3 -90 dBm
MCS4 27 dBm MCS4 -86 dBm
MCS5 25 dBm MCS5 -83 dBm
MCS6 23 dBm MCS6 -77 dBm
MCS7 22 dBm MCS7 -74 dBm
Ambient temp. range WA series -20°C (-4°F) +59°C (+138°F)WS series -20°C (-4°F) +47°C (+116°F)
HARDWARE
CPU Atheros MIPS 24KC, 400 MHz
Memory 32 MB SDRAM, 8 MB Flash
LAN Ethernet 100 Mbps
Data contained in this specification are subject to change without notice10
HAZARDOUS AREA WIRELESS SYSTEMS
The Solexy WA/WSA02 is the smallest and most powerful WiFi 1x2 MIMO access point (AP) rated for installation in hazardous locations and harsh environments. Completely configurable through its Ethernet or WiFi port via your internet browser without the need of installing any software or driver for the device.
The WA/WSA02 provides three different operating functions: AP, WiFi client and/or WDS repeater.It can be powered using the same Ethernet cable used for data or independently.
With Solexy’s WA and WS enclosures and their rugged construction water proof IP66 and IP68 combined with Atex and IECEx certificates, Solexy offers a wireless device solution for installation in classified Ex areas (gas, dust and mining) and harsh environments, including temporary submersion.
FEATURESOPERATING FUNCTIONS WiFi Access Point, WiFi Client, Repeater
WI FI802.11 g/n
ETHERNET CONNECTION Terminal strip or optional RJ45 connector.On request the unit can be supply complete of Solexy Ethernet barrier BX series
HEAVY DUTY CONSTRUCTIONExplosion proof Ex d IIC enclosure made of alluminum (WA series) or stainless steel (WS series) weather proof IP66/68.
ANTENNAS: ANF72 series flexible dipole (2 dBi) ANH73 series heavy duty J-Pole (4.35 dBi)
MOUNTING BRACKET: PM400-0001-00 Universal mounting kit for wall and pole installation
ATEX / IECEX CERTIFICATION II 2G Ex db IIC T5-T4 Gb II 2D Ex tb IIIC T110°C/T140°C Db I M2 Ex db I Mb (WS only)
AVAILABLE ACCESSORIESAPPROVALS
B00
016-
00
EXPLOSION PROOF WIFI MIMO ACCESS POINT
Dimensional drawings at page 37
Data contained in this specification are subject to change without notice 11
NOMENCLATURE
a Enclosure WA Aluminum polyester powder coated WS Stainless steel AISI 316 (CF8M) electropolish
b Antenna connection (1)
33 n° 2 RXN antenna coupler (N Female) 44 n° 2 RXF antenna coupler (RP-SMA Female)
c Cable entrie 42 n° 4 3/4” npt-f (two used for antenna connection) 44 n° 4 M25x1.5 (two used for antenna connection)
d Approval X1 IECEx and ATEX Gas and Dust (WA only) X2 IECEx and ATEX Gas, Dust and Mining (WS only)
S WA A02 10 - 42 0 X1a b c d
SPECIFICATIONS
GENERAL
Power supply 24V, 1A
Power method Passive Power over Ethernet cable (2 twists used for data, 2 twists used for power) or through dedicated terminal strip (external power supply required).A POE power supplier to be installed in safe area is included
Max power consumption 6.5W
Operating frequency 2402 - 2462 MHz
Output power 28 dBm
WiFi protocoll TX Power specification RX Power specification
Data Rate/MCS Avg. Tx Data Rate/MCS
Sensitivity
11 g 1-24 Mbps 28 dBm 1-24 Mbps -97 dBm
36 Mbps 26 dBm 36 Mbps -80 dBm
48 Mbps 25 dBm 48 Mbps -77 dBm
54 Mbps 24 dBm 54 Mbps -75 dBm
11 n MCS0 28 dBm MCS0 -96 dBm
MCS1 28 dBm MCS1 -95 dBm
MCS2 28 dBm MCS2 -92 dBm
MCS3 28 dBm MCS3 -90 dBm
MCS4 27 dBm MCS4 -86 dBm
MCS5 25 dBm MCS5 -83 dBm
MCS6 23 dBm MCS6 -77 dBm
MCS7 22 dBm MCS7 -74 dBm
MCS8 28 dBm MCS8 -95 dBm
MCS9 28 dBm MCS9 -93 dBm
MCS10 28 dBm MCS10 -90 dBm
MCS11 28 dBm MCS11 -87 dBm
MCS12 27 dBm MCS12 -84 dBm
MCS13 25 dBm MCS13 -79 dBm
MCS14 23 dBm MCS14 -78 dBm
MCS15 22 dBm MCS15 -75 dBm
Ambient temp. range WA series -30°C (-22°F) +66°C (+150°F)WS series -30°C (-22°F) +56°C (133°F)
HARDWARE
CPU Atheros MIPS 24KC, 400 MHz
Memory 128 MB SDRAM, 8 MB Flash
LAN Ethernet 10/100 Mbps
Note: (1) Antenna not included.
Data contained in this specification are subject to change without notice12
HAZARDOUS AREA WIRELESS SYSTEMS
The Solexy 3G/4G Router WiFi access point is a cost effective multipurpose solution for a wide range of wireless applications.Supporting GPRS/EDGE/UMTS/HSPA+/LTE making it possible for a user seeking an easy and fast mobile internet access.The internet connection is easily available and configurable via an internet browser without any need of installing software or drivers for the device.
B00
014-
00
EXPLOSION PROOF ROUTER WIFI ACCESS POINT
Available with different modems and options such as Wi-Fi, dual sim, GPS receiver is an unique solution for M2M and mobile data applications (M2MCloud & M2MAir ready).
With Solexy’s WA and WS enclosures and their rugged construction combined with Atex and IECEx certificates,Solexy offers a wireless device solution for installation in classified Ex areas (gas, dust and mining).
APPROVALSATEX / IECEX CERTIFICATION II 2 (1) G Ex db mb [ia Ga] IIA/IIB/IIC T6 Gb II 2 (1) D Ex mb tb [ia Da] IIIC T85°C Db I M2 (M1) Ex db mb [ia Ma] I Mb (WS only)
FEATURESOPERATING FUNCTIONS WiFi access point (Wifi to LAN or WiFi to 3G/LTE/HSPA+)WiFi client (LAN to WiFi) 3G/4G/LTE/HSPA + client (LAN to 3G/LTE/HSPA+)Serial (232-485) to 3G/LTE/HSPA+Serial (232-485) to LAN
OPERATING FREQUENCY Up to quad band 800/850, 900, AWS 1700, 1900, 2100 (Telit cellular module) according to modem feature
ADVANCEDS-232/485-TCP/UDP forwarding, ModBus gateway, NTRIP, SMS server, NTP server
MANAGEMENTDCHP (client/server), IEEE 802.1Q tagging, IPsec, OpenVPN, Firewall, NAT, PAT, DDNS, CARP, Static routing, Access Control, Syslog
OPTIONSGPS receiverDual sim
HEAVY DUTY CONSTRUCTIONExplosion proof Ex d IIC enclosure made in alluminum (WA series) or stainless steel (WS series) weather proof IP66/68
Dimensional drawings at page 37
Data contained in this specification are subject to change without notice 13
NOMENCLATURE
a Enclosure WA Aluminum polyester powder coated WS Stainless steel AISI 316 (CF8M) electropolish
b Device U 3G L LTE (1)
M LTE (1) (2)
H HSPA+ G HSPA+ (2)
c Sim slot 1 Single sim 2 Dual sim
d Interface 0 Cellular, Serial, LAN 1 Cellular, WiFi, Serial, LAN
e Antenna connection (3)
01 n° 1 AXN antenna coupler (N Female) 11 n° 2 AXN antenna coupler (N Female) 02 n° 1 AXF antenna coupler (RP-SMA Female) 22 n° 2 AXF antenna coupler (RP-SMA Female) 12 n° 1 AXF antenna coupler (RP-SMA Female) + n° 1 AXN (N Female)
f Cable entries 42 n° 4 3/4” npt-f (one used for antenna connection) 44 n° 4 M25x1.5 (one used for antenna connection)
g Approvals X3 IECEx & ATEX Dust and IIC Gas Group (WA with M and G device only) X4 IECEx & ATEX Mining, Dust and IIC Gas Group (WS with M and G device only) X5 IECEx & ATEX Dust and and IIB Gas Group (WA with U, L, H device only) X6 IECEx & ATEX Mining, Dust and IIB Gas Group (WS with U, L, H device only)
S WA H 2 1 11 - 42 0 X4a b c d e f g
SPECIFICATIONS
GENERAL
Power supply 6 - 30 VDC
Power consumption 5W
Ambient temp. range WA series WS series
-20°C (-4°F) +68°C (+154°F)-20°C (-4°F) +61°C (+141°F)
HARDWARE
CPU ARM9 450 MHz
Internal memory 128 MB RAM
RS Interface RS232 or RS485 via RJ45 connector
LAN Ethernet 100 Mbps
Network connection U version UMTS 7.2 / 5.76 Mbps
L version LTE 100 / 50 Mbps
H version HSPA+ 21 / 5.76 Mbps
Supported bands GSM 900 Class 4 (2W), DCS 1800 Class 1 (1W), EDGE 900MHz Class E2 (0.5W), EDGE 1800MHz Class E2 (0.4W). Plus:
U version WCDMA FDD B1, B8 Class 3 (0.25W)
L version WCDMA FDD B1, B5, B8 Class 3 (0.25W), LTE FDD B3, B7,B20 Class 3 (0.2W)
H version WCDMA FDD B1, B2, B4, B5, B8 Class 3 (0.25W)
Data features HSPA+ (downlink 21 Mbit/s, uplink 5,76 Mbit/s)UMTS (downlink 7,2 Mbit/s, uplink 5,76 Mbit/s)EDGE (Multi-slot class 10, max BR downlink 236,8 Kb/s)GPRS (Multi-slot class 10, max BR downlink 85,6 Kb/s)CSD (Max BR 14,4 Kb/s)Embedded protocols TCP/IP, UDP/IP, SSL, HTTP, HTTPS, FTP, SMTP, POP3, IBM MQTTClass B GSM 07.10 multiplexing protocol
WiFi 802.11 b/g/n, 802.3, 802.3u, data rate up to 150 MbpsUp to 8 simultaneuos connection
SOFTWARE
Management DHCP (client/server), IEEE 802.1Q tagging, IPsec, OpenVPN, Firewall, NAT, PAT, DDNS, CARP, Static routing, Access control, Syslog
Advanced RS-232/485-TCP/UDP forwarding, ModBus gateway, NTRIP, SMS server, NTP
NOTE: (1) Approved for use in European Union only (2) RF low power device suitable for use in IIC gas group (3) Antenna not included
Data contained in this specification are subject to change without notice14
HAZARDOUS AREA WIRELESS SYSTEMS
The Solexy Bluetooth wireless serial adapter is a cost effective solution for serial data transmission.
The Class 1 Bluetooth radio can reach wireless transmission distance of 100 meters.
Available for RS232 or RS485/422 serial port, making it a flexible solution for M2M applications.
With Solexy’s WA and WS enclosures and their rugged construction combined with Atex and IECEx certificates, Solexy offers a wireless device solution for installation in classified Ex areas (gas, dust and mining).
FEATURESOPERATING FUNCTIONS RS232 or RS485/RS422 serial cable replacement
BLUETOOTH v2.0 + EDRSupports up to 4 multiple simultaneous connectionsSupports Bluetooth profiles SPP (Serial Port Profile)Interoperability with PDA, laptops, etc...
CONFIGURATION Easy to use Windows configuration tool available (no external drivers required)
B00
017-
00 EXPLOSION PROOF BLUETOOTH SERIAL ADAPTER
APPROVALSATEX / IECEX CERTIFICATION II 2 (1) G Ex db mb [ia Ga] IIA/IIB/IIC T6 Gb II 2 (1) D Ex mb tb [ia Da] IIIC T85°C Db I M2 (M1) Ex db mb [ia Ma] I Mb (WS only)
Data contained in this specification are subject to change without notice 15
NOMENCLATURE
a Enclosure WA Aluminum polyester powder coated WS Stainless steel AISI 316 (CF8M) electropolish
b Device B10 RS232 Bluetooth serial adpater B11 RS485/RS422 Bluetooth serial adapter
c Antenna connection (1)
01 n° 1 AXN antenna coupler (N Female) 02 n° 1 AXF antenna coupler (RP-SMA Female)
d Cable entries 42 n° 4 3/4” npt-f (one used for antenna connection) 44 n° 4 M25x1.5 (one used for antenna connection)
e Approval X3 IECEx and ATEX Gas and Dust (WA only) X4 IECEx and ATEX Gas, Dust and Mining (WS only)
NOTE: (1) Antenna not included
S WA B10 01 - 42 0 X4a b c d e
SPECIFICATIONS
GENERAL
Power supply 5-12VDC
Power consumption min 2 mA - max 80 mA
Ambient temp. range WA seriesWS series
-20°C (-4°F) +68°C (+154°F)-20°C (-4°F) +61°C (+141°F)
SERIAL INTERFACE
Serial speed up to 921.6 kbps
CTR/RTS flow control DTR/DSR for loop-back & full transfer (B10 type only)
RADIO
Max TX power +18 dBm
Max EDR Transmit power +6 dBm
Receiver sensitivity -88 dBm
BLUETOOTH INTERFACE
Bluetooth v2.0 + EDR
Class 1
Profile SPP
Dimensional drawings at page 37
Data contained in this specification are subject to change without notice16
HAZARDOUS AREA WIRELESS SYSTEMS
Solexy radiomodem is a VHF/UHF simplex/half-duplex high quality radiomodem operating on 12.5 kHz, 25 kHz or 50 kHz channels available in 169 MHz and 868 MHz band in accordance with European Decision 2005/928/CE.
These products were developed as a licence free device. Solexy radiomodems are supplied complete with a RS232 / RS485 interface, optoisolated input and relay output installed in our explosion proof housing WA and WS series that allows a serial data transmission in classified area Ex.
Solexy radiomodems are fully transparent to the user and configurable from the PC by means of a dedicated software for the desired functions.
FEATURESLOW POWERLow power consumption in both RX and TX mode with selectable power saving mode by software and on/off switching controlled via DTR criteria
STORE AND FORWARDStore & Forward mode with 1024 byte maximum buffer size
ADAPTIVE FREQUENCY AGILITY Adaptive Frequency Agility on 2 or 3 channels
SOFTWARE CONFIGURATIONComplete configuration by means of a PC through dedicated software
ADVANCED PROTOCOL Point to point, Point to Multipoint, Broadcasting mode or Adresses management, Adresses stored in configuration or from DTE, Digipeater mode, Remote configuration through radio network, Adresses reversing for the answer, Echo function
TRANSPARENT SERIAL TRANSMISSION DATA PLUS EXTRA DIGITAL INPUT/OUTPUT Serial trasmission RS232 or RS485 transparent to the user plus optoisolated input and relay output may be used for alarms and/or actuation
NOMENCLATURE
a Enclosure WA Aluminum polyester powder coated WS Stainless steel AISI 316 (CF8M) electropolish
b Device 512 Radiomodem VHF 169 MHz, 500 mW RF power output 542 Radiomodem UHF 868 MHz, 500 mW RF power output
c Antenna connection 03 n° 1 RXN antenna coupler (N Female) 04 n° 1 RXF antenna coupler (RP-SMA Female)
d Cable entries 42 n° 4 3/4” npt-f (one used for antenna connection) 44 n° 4 M25x1.5 (one used for antenna connection)
e Approvals X1 IECEx and ATEX Gas and Dust (WA only) X2 IECEx and ATEX Gas, Dust and Mining (WS only)
S WA 512 01 - 42 0 X3a b c d e
B00
012-
00
EXPLOSION PROOF VHF & UHF RADIOMODEMS
APPROVALSATEX / IECEX CERTIFICATION II 2G Ex db IIC T5-T4 Gb II 2D Ex tb IIIC T110°C/T140°C Db I M2 Ex db I Mb (WS Only)
Data contained in this specification are subject to change without notice 17
SPECIFICATIONS DEVICE
GENERAL 512 542
Operating band 169.400 MHz169.475 MHz
868.400 MHz869.650 MHz
Canalization 12.5 | 25 | 50 kHz
Modulation 9K00F1D or 18K0F1D
Radio data rate (Tx/Rx) 4800 bps @ 12.5 kHz | 9600 bps @ 25 kHz | 19200 bps @ 50 kHz
Frequency stability ±2 ppm ± 1 ppm
Supply voltage 9-32 VDC
Rx consumption (@12 VDC) ≈ 30 mA
Tx consumption (@12 VDC) ≈ 200 mA
Relay output rating 1A@24V AC/DC resistive load (Normally Open)
Digital input 5-24VDC - 3.5-20VAC ZINP 2.2 kΩ (optoisolated)
Ambient temp. range WA seriesWS series
-30°C (-22°F) +70°C (158°F)-30°C (-22°F) +65°C (149°F)
Housing material WA seriesWS series
Die cast aluminium polyester powder coatedAISI 316 (CF8M) electropolished
Weather proof IP 66/68
TRANSMITTER 512 542
Output power 25/150/500 mW 25/150/500 mW
Frequency deviations ± 1.8 kHz @ 12.5 kHz± 3.6 kHz @ 25 kHz± 4.8 kHz @ 50 kHz
Output power stability ± 1.5 dB
RECEIVER 512 542
Type CLASS 1 - LBT and AGILITY CLASS 2 - LBT and AGILITY
Sensibility @ BER < 10-2 12.5 kHz 25 kHz50 kHz
< -110 dBm< -107 dBm< -105 dBm
< -107 dBm< -105 dBm
INTERFACE 512 542
Type RS232 and RS485
Data rate From 1200 to 57600 bps
Data format Asyncrhronous 8, N, 1 - 8, E, 1 - 8, O, 1 - 7, E, 1 - 7, O, 1 - 7, N, 2
Operative modality Simplex or half-duplex
RS232 / RS485plus Digital Input and Relay Output
RS232 / RS485plus Digital Input and Relay Output
Dimensional drawings at page 37
Data contained in this specification are subject to change without notice18
HAZARDOUS AREA WIRELESS SYSTEMS
The Solexy MODBUS RTU radiomodem is a VHF/UHF high quality 500 mW radiomodem operating on 12,5 or 25 kHz channels available in 169 MHz and 868 MHz band in according to European Decision 2005/928/CE.
These products are develop in order to be a licence free device.
The Solexy MODBUS RTU radiomodems are supply complete with 4 digital input, 2 digital output plus 2 analog input and 2 analog output 4-20 mA that allows to has an Modbus RTU node. The RS485 interface permit also the connection up to 4 Modbus module.
The WA and WS anclosure thanks to its rugged construction combined to Atex and IECEx certificate achieves to have an Modbus RTU data transmission in classified area Ex.
EXPLOSION PROOF MODBUS RTU RADIOMODEMS
FEATURESMODBUS RTU The Solexy MODBUS RTU radiomodem can be used on all Modbus RTU application
WIDE RANGE OF TRANSMISSION OPTION Mirror (point to point), Modbus RTU, Modbus multi master and standard Radiomodem option completely transparent to the user also in case of complex route
MODBUS RTU NODE 4 PNP digital input combinet to 2 relay output plus 2 analg input and 2 optoisolated analog output 4-20 mA allows to use the radiomodem as a complete Modbus RTU node.
LOW POWER Low power consumption in both RX and TX mode and bistable relay on digital output allows the Solexy radiomodem suitable to battery operation
ADAPTIVE FREQUENCY AGILITYAdaptive Frequency Agility on 2 or 3 channels
SOFTWARE CONFIGURATION Complete configuration by PC through dedicated software
ENCRYPTION TRANSMISSION DATA Secure transmission data thanks to AES (Advanced Encryption Standard) at 128 bit
NOMENCLATURE
a Enclosure WA Aluminum polyester powder coated WS Stainless steel AISI 316 (CF8M) electropolish
b Device 510 Modbus RTU Radiomodem VHF 169 MHz, 500 mW RF power output 540 Modbus RTU Radiomodem UHF 868 MHz, 500 mW RF power output
c Antenna connection 01 n° 1 AXN antenna coupler (N Female) 02 n° 1 AXF antenna coupler (RP-SMA Female)
d Cable entries 42 n° 4 3/4” npt-f (one used for antenna connection) 44 n° 4 M25x1.5 (one used for antenna connection)
e Approval X3 IECEx and ATEX Gas and Dust (WA only) X4 IECEx and ATEX Gas, Dust and Mining (WS only)
S WA 510 01 - 42 0 X3a b c d e
B00
013-
00
APPROVALSATEX / IECEX CERTIFICATION II 2 (1) G Ex db mb [ia Ga] IIA/IIB/IIC T6 Gb II 2 (1) D Ex mb tb [ia Da] IIIC T85°C Db I M2 (M1) Ex db mb [ia Ma] I Mb (WS only)
Data contained in this specification are subject to change without notice 19
SPECIFICATIONS DEVICE
GENERAL 510 540
Operating band 169.400 MHz169.475 MHz
868.000 MHz869.650 MHz
Canalization 12.5 | 25 | 50 kHz 25 | 50 kHz
Modulation 9K00F1D or 18K0F1D
Radio data rate (Tx/Rx) 4800 bps @ 12.5 kHz | 9600 bps @ 25 kHz | 19200 bps @ 50 kHz
Frequency stability ±2 ppm ± 1 ppm
Supply voltage 9-32 VDC or 3.3 - 4.8 battery operated
Rx consumption (@12 VDC) ≈ 30 mA (RS232/485 relè off)
Tx consumption (@12 VDC) ≈ 200 mA
Sleep consumption Battery operated < 10 μA | 12 VCD operated < 150 μA
Digital outputs rating n° 2 1A@24V AC/DC resistive load (Normally Open)
Digital inputs n° 4 PNP
Digital counter n° 1 PNP (max frequency input 10 Hz)
Analog inputs n° 2 4-20 mA (passive)
Analog outputs n° 2 4-20 mA (passive)
Ambient temp. range WA seriesWS series
-30°C (-22°F) +70°C (+158°F)-30°C (-22°F) +65°C (+149°F)
Housing material WA seriesWS series
die cast aluminium polyester powder coatedAISI 316 (CF8M) electropolished
Weather proof IP 66/68
TRANSMITTER 510 540
Output power 25/150/500 mW 25/150/500 mW
Frequency deviations ± 1.8 kHz @ 12.5 kHz± 3.6 kHz @ 25 kHz± 4.8 kHz @ 50 kHz
Output power stability ± 1.5 dB
RECEIVER 510 540
Type CLASS 1 - LBT and AGILITY CLASS 2 - LBT and AGILITY
Sensibility @ BER < 10-2 12.5 kHz25 kHz50 kHz
< -110 dBm< -107 dBm < -105 dBm
< -107 dBm< -105 dBm
INTERFACE 510 540
Type RS485
Data rate from 1200 to 57600 bps
Data format Asyncrhronous 8, N, 1 - 8, E, 1 - 8, O, 1 - 7, E, 1 - 7, O, 1 - 7, N, 2
Operative modality Simplex or half-duplex
4 digital IN2 digital OUT2 analog IN 4-20 mA2 analog OUT 4-20 mARS485 Modbus RTU port
4 digital IN2 digital OUT2 analog IN 4-20 mA2 analog OUT 4-20 mARS485 Modbus RTU port
MODBUS
Dimensional drawings at page 37
Data contained in this specification are subject to change without notice20
HAZARDOUS AREA WIRELESS SYSTEMS
The Solexy Ethernet radiomodems is a VHF/UHF high quality 500 mW radiomodem operating on 12,5 or 25 kHz channels avialable 169 MHz and 868 MHz band.
These products are develop in order to be a licence free device.
The Solexy Ethernet radiomodems are supplied complete with RS485 interface and Ethernet port plus optoisolated input and relay output installed in our explosion proof housing WA and WS series that allows a serial data transmission also in classified area Ex.
The WA and WS anclosure thanks to its rugged construction combined to Atex and IECEx certificate achieves to have an Modbus RTU data transmission in classified area Ex.
EXPLOSION PROOF ETHERNET RADIOMODEMS
FEATURESRS485 AND ETHERNET SERIAL DATA TRANSMISSION Serial transmission on RS485 or Ethernet port transparent to the user plus optoisolated input and realy output may used for alarms and/or actuation
WIDE RANGE OF TRANSMISSION OPTIONMirror (point to point), Modbus RTU over TCP, Modbus multi master and standard Radiomodem option completely transparent to the user also in case of complex route
MODBUS RTU OVER TCPSuitable for use as a Modbus RTU over TCP Server
LOW POWERLow power consumption in both RX and TX mode with selectable power saving mode by software and on/off switching controlled via DTR criteria
ADAPTIVE FREQUENCY AGILITYAdaptive Frequency Agility on 2 or 3 channels
WEB SERVER AND RADIO NETWORK STATUS Thanks to the web server integrated it is possible to configure the device and check the Radio Network Status through a dedicated utilities
ENCRYPTION TRANSMISSION DATA Secure transmission data thanks to AES (Advanced Encryption Standard) at 128 bit
NOMENCLATURE
a Enclosure WA Aluminum polyester powder coated WS Stainless steel AISI 316 (CF8M) electropolish
b Device 51E Modbus RTU Radiomodem VHF 169 MHz, 500 mW RF power output 54E Modbus RTU Radiomodem UHF 868 MHz, 500 mW RF power output
c Antenna connection 03 n° 1 RXN antenna coupler (N Female) 04 n° 1 RXF antenna coupler (RP-SMA Female)
d Cable entries 42 n° 4 3/4” npt-f (one used for antenna connection) 44 n° 4 M25x1.5 (one used for antenna connection)
e Approval X1 IECEx and ATEX Gas and Dust (WA only) X2 IECEx and ATEX Gas, Dust and Mining (WS only)
S WA 51E 01 - 42 0 X3a b c d e
B00
019-
00
APPROVALSATEX / IECEX CERTIFICATION II 2G Ex db IIC T5-T4 Gb II 2D Ex tb IIIC T110°C/T140°C Db I M2 Ex db I Mb (WS Only)
Data contained in this specification are subject to change without notice 21
DEVICE
GENERAL 51E 54E
Operating band 169.400 MHz169.475 MHz
868.000 MHz869.650 MHz
Canalization 12.5 | 25 | 50 kHz 25 | 50 kHz
Modulation 9K00F1D or 18K0F1D
Radio data rate (Tx/Rx) 4800 bps @ 12.5 kHz | 9600 bps @ 25 kHz | 19200 bps @ 50 kHz
Frequency stability ±2 ppm ± 1 ppm
Supply voltage 9-32 VDC
Rx consumption (@12 VDC) ≈ 30 mA (RS232/485 relè off)
Tx consumption (@12 VDC) ≈ 200 mA
Relay outputs rating 1A@24V AC/DC resistive load (Normally Open)
Digital inputs 5-24VDC - 3.5-20VAC ZINP 2.2 kΩ (optoisolated)
Ambient temp. range WA seriesWS series
-30°C (-22°F) +70°C (+158°F)-30°C (-22°F) +65°C (+149°F)
Housing material WA seriesWS series
die cast aluminium polyester powder coatedAISI 316 (CF8M) electropolished
Weather proof IP 66/68
TRANSMITTER 51E 54E
Output power 25/150/500 mW 25/150/500 mW
Frequency deviations ± 1.8 kHz @ 12.5 kHz± 3.6 kHz @ 25 kHz
Output power stability ± 1.5 dB
RECEIVER 51E 54E
Type CLASS 1 - LBT and AGILITY CLASS 2 - LBT and AGILITY
Sensibility @ BER < 10-2 12.5 kHz25 kHz50 kHz
< -110 dBm< -107 dBm < -105 dBm
< -107 dBm< -105 dBm
SERIAL INTERFACE 51E 54E
Type RS485
Data rate from 1200 to 57600 bps
ETHERNET INTERFACE 510 54E
Standard IEEE802.3
Connection RJ45
Data transmission 10/100 Mbps Auto-Detection
DHCP Server, Client
Auto MDI/MDI-X Yes
Protocols TCP/IP, Modbus RTU over TCP (server)
Configuration WEB Server, Windows Utility
RS485Ethernet1 digital IN1 digital OUT
RS485Ethernet1 digital IN1 digital OUT
Dimensional drawings at page 37
SPECIFICATIONS
Data contained in this specification are subject to change without notice22
HAZARDOUS AREA WIRELESS SYSTEMS
Solexy’s Explosion proof RF junction boxes are specifically designed to allow a radio frequency coax cable junction/extension in hazardous location. There are many installations in Radio Frequency where you are going from a non-rated area to a hazardous area. With the Solexy HWA and HWS series RF Junction boxes there is now a solution to this type of installation.
With our RX series Antenna connection and the HWA/HWS series junction box an hazardous area field connection can now be made. Utilizing the RX antenna coupler the antenna is not required to be Haz Loc or Ex rated. This simple solution is available with many options with coax connections and Antennas or as a cable connection to an antenna mounted on a mast.
Solexy’s Explosion proof RF junction boxes are available in two configurations, the HWA series is a more cost effective option that is manufactured from corrosion resistant low copper aluminum. The HWA series is powder coated to prevent corrosion in harsher outdoor environments. The HWS series is manufactured in 316 Series Stainless Steel (CF8M). This box is built for the toughest environments when nothing else but Stainless will do.
FEATURESHEAVY DUTY CONSTRUSTION Explosion proof Ex d IIC enclosure made in alluminum (WA series) or stainless steel (WS series)
WEATHER PROOF IP66 / IP68
CABLE ENTRIES M25x1,5 or 3/4” npt-f
TEMPERATURE RANGE -40°C to +80°C
B00
018-
00
EXPLOSION PROOF RF JUNCTION BOX
Dimensional drawings at page 37
Data contained in this specification are subject to change without notice 23
NOMENCLATURE
a Enclosure WA Aluminum polyester powder coated WS Stainless steel AISI 316 (CF8M) electropolish
b Connector 001 RP-SMA Male 002 RP-SMA Female 003 SMA Male 004 SMA Female 007 N Male 008 N Female 009 TNC Male 010 TNC Female 011 BNC Male 012 BNC Female
ENCLOSUREAtex and IECEx certified II 2G Ex db IIC T6-T5-T4 Gb II 2D Ex tb IIIC T110°C / T110°C / T140°C I M2 Ex d I Mb (WS only)
Atex certificate nr. EXA 14 ATEX 0042 and IECEx certificate nr. IECEx EXA 14.0001
ANTENNA BARRIERAtex and IECEx certified I M2 (M1) Ex db mb [ia Ma] I Mb II 2 (1) G Ex db mb [ia Ga] IIA/IIB/IIC T5/T6 Gb II 2 (1) D Ex mb tb [ia Da] IIIC T100°C/T80°C Db
Atex certificate nr. EXA 15 ATEX 0042 and IECEx certificate nr. IECEx EXA 15.0005
c Cable entries 42 n° 4 3/4” npt-f (one used for antenna coupler) 44 n° 4 M25x1.5 (one used for antenna coupler)
d Approval X1 IECEx and ATEX Gas and Dust (WA only) X2 IECEx and ATEX Gas, Dust and Mining (WS only)
NOTE: Antenna and Antenna coupler not included
H WA 001 00 - 42 0 X1a b c d
APPROVALS
ANH and ANF series antennas are hand built and tuned for the best performance.
The rugged construction of the ANH will stand upto high levels of abuse, and the flexible design of the ANF
“gives” to impacts to prevent damage and misalignment of the antenna.
Their sealed UV and corrosion resistant housings and nickel plated fittings with gold contacts provide a reliable RF
connection in hostile environments.
25
AccessoriesHeavy duty antennas and cables
Data contained in this specification are subject to change without notice26
ACCESSORIES
The range and performance of a RF link is critically dependent upon the antenna and it is one of the more complex aspects of on RF design.
An antenna can make or break a wireless network.The proper antenna can optimize the range, reliability and performance of a radio network.
FEATURESHYBRIDTM TECHNOLOGY Embedded HybridTM circuitry allows for maximum perfomance and unmatched durability
ANH HEAVY DUTY SERIES Rugged construction allows the use of our antennas in hostile envinronments where weather and abuse are a factor
FREQUENCY Available for 868 MHz, 900 MHz and 2.4 GHz
N MALE CONNECTORAvailable for vertical or 90° mounting
DIPOLE ANH SERIESHEAVY DUTY ANTENNA
B00
006-
00
a Frequency 4 868 MHz 5 900 MHz 7 2.4 GHz
b Antenna connection 3 N Female C N Male
c Antenna mounting S Straight (vertical) R Elbow (90°)
ANH 5 2 - C N S Ua b c
NOMENCLATURE
Data contained in this specification are subject to change without notice 27
DIMENSIONAL DRAWINGS
SPECIFICATIONS Radiation Omni
Polarization Vertical
Wave 1/2 (dipole)
Connector N Male Brass nickel plated
Material UV resistant ABS
Ambient temp. range -40°C (-40°F) +80°C (+176°F)
ANH 42 ANH 52 ANH 72
Frequency Range
855 - 883 MHz
890 - 935 MHz
2.35 - 2.55 GHz
Impedance (nominal)
50Ω @ 868 MHz
50Ω @ 915 MHz
50Ω @ 2.45 GHz
VSWR (average) 1.14 : 1 1.14 : 1 1.13 : 1
Gain max 2.00 dBi 2.00 dBi 2.00 dBi
ANH42
1
1,2
1,4
1,6
1,8
2
840 845 850 855 860 865 870 875 880 885 890
VS
WR
Frequency (MHz)
ANH52
1
1,2
1,4
1,6
1,8
2
890 895 900 905 910 915 920 925 930 935
VS
WR
Frequency (MHz)
ANH72
1
1,2
1,4
1,6
1,8
2
2,35 2,4 2,45 2,5 2,55
VS
WR
Frequency (GHz)
Models
ANH42-CNSUANH52-CNSUANH72-CNSU
0.93[23.62mm]
B
0.93[23.62mm]
1.60[40.64mm]
A
Models
ANH42-CNRUANH52-CNRUANH72-CNRU
Model A inch [mm]
ANH42-CNSU 6.45 [158.20]ANH52-CNSU 6.45 [158.20]ANH72-CNSU 3.85 [97.80]
Model B inch [mm]
ANH42-CNRU 6.24 [158.50]ANH52-CNRU 6.24 [158.50]ANH72-CNRU 3.75 [95.25]
Data contained in this specification are subject to change without notice28
ACCESSORIES
HEAVY DUTY ANTENNA
The range and performance of a RF link is critically dependent upon the antenna and it is one of the more complex aspects of on RF design.
An antenna can make or break a wireless network.The proper antenna can optimize the range, reliability and performance of a radio network.
FEATURESJ-POLE TECHNOLOGY This highly stable, higher gain antenna goes the distance and is in a smaller package compared to other high gain antennas. With a higher gain ground plane it is less sensitive to its installed environment ensuring stable communication at longer distances
ANH HEAVY DUTY SERIES Rugged construction allows the use of our antennas in hostile envinronments where weather and abuse are a factor
FREQUENCY Available for 868 MHz, 900 MHz and 2.4 GHz
N MALE CONNECTOR Available for vertical or 90° mounting
J-POLE ANH SERIES
B00
007-
00
a Frequency 4 868 MHz 5 900 MHz 7 2.4 GHz
b Antenna connection 3 N Female C N Male
c Antenna mounting S Straight (vertical) R Elbow (90°)
ANH 5 3 - C N S Ua b c
NOMENCLATURE
Data contained in this specification are subject to change without notice 29
DIMENSIONAL DRAWINGS
SPECIFICATIONS Radiation Omni
Polarization Vertical
Wave J-pole configuration
Connector N Male Brass nickel plated
Material UV resistant ABS
Ambient temp. range -40°C (-40°F) +80°C (+176°F)
ANH 43 ANH 53 ANH 73
Frequency Range 855 - 883 MHz
890 - 935 MHz
2.35 - 2.55 GHz
Impedance (nominal)
50Ω @ 868 MHz
50Ω @ 915 MHz
50Ω @ 2.45 GHz
VSWR (average) 1.4 : 1 1.4 : 1 1.4 : 1
Gain max 3.00 dBi 3.00 dBi 4.35 dBi
1
1,2
1,4
1,6
1,8
2
840 845 850 855 860 865 870 875 880 885 890
VS
WR
Frequency (MHz)
ANH43
1
1,2
1,4
1,6
1,8
2
890 895 900 905 910 915 920 925 930 935
VS
WR
Frequency (MHz)
ANH53
1
1,2
1,4
1,6
1,8
2
2,35 2,4 2,45 2,5 2,55
VS
WR
Frequency (GHz)
ANH73
Models
ANH43-CNSUANH53-CNSUANH73-CNSU
0.79[20.10mm]
B
0.79[20.10mm]
1.50[38.10mm]
A
Models
ANH43-CNRANH53-CNRANH73-CNRU
Model A inch [mm]
ANH43-CNSU 13.55 [344.20]ANH53-CNSU 13.55 [344.20]ANH73-CNSU 6.17 [156.70]
Model B inch [mm]
ANH43-CNRU 13.95 [354.30]ANH53-CNRU 13.95 [354.30]ANH73-CNRU 6.57 [166.90]
Data contained in this specification are subject to change without notice30
ACCESSORIES
The Solexy Highly Flexible Antenna is designed for rough environments, this along with our Heavy Duty Line of antennas meets the demands of the tough applications while being affordable yet durable.
Solexy Antennas have met the demands and are well known throughout the Oil and Gas industries.
FEATURES
FLEXIBLE ANF SERIES
B00
008-
00
a Frequency 4 868 MHz 5 900 MHz 7 2.4 GHz
b Antenna connection 3 N Female C N Male
b Antenna mounting S Straight (vertical) R Elbow (90°)
ANF 5 2 - C N S Ua b c
NOMENCLATURE
FLEX TECHNOLOGY This Highly flexible antenna was designed to meet the requirements of a high traffic environment, one hit and it bounces right back. It also has over a 25Kg (55 lbs.) pull strength. This antenna has the signal dependability of a Dipole antenna and the flexibility to bounce back from any hit.
ANF HEAVY DUTY SERIES Rugged construction allows the use of our antennas in hostile envinronments where weather and abuse are a factor.
FREQUENCY Available for 868 MHz, 900 MHz and 2.4 GHz
N MALE CONNECTOR Available for vertical or 90° mounting
HEAVY DUTY ANTENNA
Data contained in this specification are subject to change without notice 31
DIMENSIONAL DRAWINGS
SPECIFICATIONS Radiation Omni
Polarization Vertical
Wave 1/2
Connector N Male Brass nickel plated
Antenna Tip Soft black PVC
Adapter Black Delrin
Material UV resistant PUR
Ambient temp. range -40°C (-40°F) +80°C (+176°F)
ANF 42 ANF 52 ANF 72
Frequency range 855 - 883 MHz
902 - 928 MHz
2.35 - 2.55 GHz
Impedance (nominal)
50Ω @ 868 MHz
50Ω @ 915 MHz
50Ω @ 2.45 GHz
VSWR (average) 1.14 : 1 1.14 : 1 1.14 : 1
Gain max 2.00 dBi 2.00 dBi 2.00 dBi
1
1,2
1,4
1,6
1,8
2
840 845 850 855 860 865 870 875 880 885 890
VS
WR
Frequency (MHz)
VSWR
ANF42
1
1,2
1,4
1,6
1,8
2
890 895 900 905 910 915 920 925 930 935 940V
SW
R
Frequency (MHz)
VSWR
ANF52
1
1,2
1,4
1,6
1,8
2
2,35 2,4 2,45 2,5 2,55
VS
WR
Frequency (GHz)
VSWR
ANF72
Models
ANF52-CNSUANF42-CNSUANF72-CNSU
Models
ANF52-CNRUANF42-CNRUANF72-CNRU
A
0.8 inch[20.32mm]
1.13 inch[28.70mm]
B
Model A inch [mm]
ANF42-CNSU 11 [279.4]ANF52-CNSU 11 [279.4]ANF72-CNSU 7 [177.8]
Model B inch [mm]
ANF42-CNRU 11.4 [289.56]ANF52-CNRU 11.4 [289.56]ANF72-CNRU 7.4 [187.96]
Data contained in this specification are subject to change without notice32
ACCESSORIES
HEAVY DUTY ANTENNA
The Solexy’s ANHA and ANHB series is a selection of heavy duty antennas specifically designed for satellite applications, covering a wide range of frequency bands including GPS, GLONASS and IRIDIUM.
The ANHA and ANHB series are passive, narrow bandwidth and high gain antennas, perfectly compatible with Solexy’s AX and RX intrinsically safe antenna couplers.
The ANHA and ANHB series are RHCP (Right Hand Circular Polarized) in order to be compatible with the propagated GPS signals.
FEATURES
GPS ANH SERIES
B00
009-
00
a Frequency / System A 1575.42 MHz / GPS-GLONASS B 1621 MHz / IRIDIUM
b Antenna connection 3 N Female C N Male
c Antenna mounting S Straight (vertical) R Elbow (90°, only N Male connector)
ANH A A - C N S Ea b c
NOMENCLATURE
PASSIVE High gain passive execution to be used in cominatiotn with intrinsically safe Solexy antenna couplers
ANH HEAVY DUTY SERIES Rugged construction allows the use of our antennas in hostile envinronments where weather and abuse are a factor
FREQUENCY Available for GPS/GLONASS and IRIDIUM systems
N CONNECTOR Available N Male straight or elbow and N Female stright bulkhead
Data contained in this specification are subject to change without notice 33
DIMENSIONAL DRAWINGS
SPECIFICATIONS Polarization Right Hand Circular (RHCP)
Connector N Male or Female brass nickel plated
Material Fiberglass
Ambient temp. range -40°C (-40°F) +80C (+176F)
ANHA Receiving Frequency
1575.42 MHz GPS/GLONASS Systems
ANHB Center Frequency
1621 MHz IRIDIUM Systems
ANHA ANHB
-10dB Bandwidth 15 MHz 9 MHz
Impedance 50Ω 50Ω
VSWR 1.5 1.5
Gain (@ Zenith) 4.50 dBic 4.00 dBic
Polarization RHCP RHCP
Frequency temperaturecoefficient
20 ppm/°C 20 ppm/°C
ANHAA-_NSIANHBA-_NSI
ANHAA-CNRIANHBA-CNRI
1.77[45.00mm]
3.94[100.00mm]
1.77[45.00mm]
3.94[100.00mm]
1.97[50.00mm]
Radiation pattern
Data contained in this specification are subject to change without notice34
ACCESSORIESB
0001
0-00
a Coax cable type A RG-316 B LMR-100A-PVC C I999
bb RF Connector Coupler Side
cc RF Connector Radio Side see below
dd Coax cable length 06 06“ (15 cm) 12 12“ (30 cm) 18 18“ (45 cm) 24 24“ (60 cm) 30 30“ (75 cm)
PT A 01 03 06a bb cc dd
NOMENCLATURE
01 RP-SMA Male02 RP-SMA Female03 SMA Male04 SMA Female07 N Male08 N Female09 TNC Male10 TNC Female11 BNC Male12 BNC Female13 MCX Male 90°15 MMCX Male 90°16 RP-SMA Male 90°18 SMA Male 90°19 SMB Male21 RP-TNC Male23 SMB Female24 U.FL Female29 N Female bulkehead
01 RP-SMA Male03 SMA Male
RF CONNECTOR COUPLER SIDE (bb) RF CONNECTOR RADIO SIDE (cc)
dd
SPECIFICATIONS
COAX CABLE EXTENSIONCABLES
Data contained in this specification are subject to change without notice 35
37
DIMENSIONAL DRAWINGS
Data contained in this specification are subject to change without notice38
DIMENSIONAL DRAWINGS
DIMENSIONAL DRAWINGS3.
52”
[89,
5 m
m]
Cable entries(npt or metric)
M8x1.25 - 6H
M6x1 - 6H
1.968”[50 mm]
3.661”[93 mm]
A
B
D EC
Cable entries(npt or metric)
M8x1.25 - 6H
M6x1 - 6H
1.968”[50 mm]
3.661”[93 mm]
3.54
”[9
0 m
m]
A
B
D EC
WS
WA
Data contained in this specification are subject to change without notice 39
SPECIFICATIONS
Device Model A (*) B (*) C (*) D (*) E (*)
Explosion proof VHF & UHF radiomodems
512542
S WA - 179,8 mm [7.08’’] 58,5 mm [2.30’’] 180 mm [7.09’’] -
S WS - 180,5 mm [7.11’’] 58,5 mm [2.30’’] 196 mm [7.72’’] -
Explosion proof Modbus RTU radiomodems
510540
S WA - 179,8 mm [7.08’’] 58,5 mm [2.30’’] 180 mm [7.09’’] -
S WS - 180,5 mm [7.11’’] 58,5 mm [2.30’’] 196 mm [7.72’’] -
51E54E
S WA - 179,8 mm [7.08’’] 70 mm [2.76’’] 180 mm [7.09’’] -
S WS - 180,5 mm [7.11’’] 70 mm [2.76’’] 196 mm [7.72’’] -
Explosion proof Router WiFi access point
U_0L_0M_0H_0G_0
S WA 58,5 mm [2.30’’] 179,8 mm [7.08’’] - 180 mm [7.09’’] -
S WS 58,5 mm [2.30’’] 180,5 mm [7.11’’] - 196 mm [7.72’’] -
U_1L_1M_1H_1G_1
S WA 58,5 mm [2.30’’] 179,8 mm [7.08’’] - 180 mm [7.09’’] -
S WS 58,5 mm [2.30’’] 180,5 mm [7.11’’] - 196 mm [7.72’’] -
Explosion proof WiFi access point
A01S WA - 179,8 mm [7.08’’] 70 mm [2.76’’] 180 mm [7.09’’] -
S WS - 180,5 mm [7.11’’] 70 mm [2.76’’] 196 mm [7.72’’] -
Explosion proof WiFi MIMO access point
A02S WA - 179,8 mm [7.08’’] 70 mm [2.76’’] 180 mm [7.09’’] 70 mm [2.76’’]
S WS - 180,5 mm [7.11’’] 70 mm [2.76’’] 196 mm [7.72’’] 70 mm [2.76’’]
Explosion proof Bluetooth serial adapter
B10B11
S WA - 179,8 mm [7.08’’] 58,5 mm [2.30’’] 180 mm [7.09’’] -
S WS - 180,5 mm [7.11’’] 58,5 mm [2.30’’] 196 mm [7.72’’] -
Explosion proof RF junction box
001002003004007008009010011012
H WA - 179,8 mm [7.08’’] 70 mm [2.76’’] 180 mm [7.09’’] -
H WS - 180,5 mm [7.11’’] 70 mm [2.76’’] 196 mm [7.72’’] -
(*) dimension related to N female antenna connector
NOTES
10168follow us
C00002-00
DOWNLOAD PRODUCT CATALOGUEwww.solexy.net/PS
www.SOLEXY.net