Instruction Manual Specification Wingspan:1180mm Fuselage Length:1080mm Flying weight:1150g Servo:9gX4 Battery:11.1v 2200mAh 20C Li-Po ESC:40AX2 Motor:KV3300X2 Wing loading:63g/dm 2
Welcome message from author
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Instruction ManualSpecification
Wingspan:1180mmFuselage Length:1080mm
Flying weight:1150gServo:9gX4
Battery:11.1v 2200mAh 20C Li-PoESC:40AX2Motor:KV3300X2Wing loading:63g/dm2
1
2
RTF INCLUDING
3
RTF including:fuselagewingelevatorlanding gearVertical stabilizerplastic parts setHardwareElevatoredf set gluedecalbalance chargerLI-Po battery (11.1V 2200mAh 20C)transmitterAdaptorCockpitESC
4
As shown,Insert the speed controllers into fuselage.
As shown, Apply the foam glue onthe joiner of the left and right horizontal stabilizer.
Insert the vertical stabilizer into the fuselage.
As shown,Fix the EDF set onfuselage with 3X40mm screw.
As shown,Glue the horizontal stabilizer in place.
As shown,Fix the vertical stabilizer onfuselage with 2.3X20mm screw.
5
Insert the direction pushrod into the hold of quick-controller and tightenclamp connectors.
As shown, Insert speed controllerwires into THR channel of receiver.
As shown,Fix the nose landing gear on fuselage with 2.5X8mm screw.
As shown, Insert Z-bend of pushrodinto the hole of the nose landing gear.
As shown, Apply the foam glue to the stuffing foam and insert it into fuselageas shown.
As shown,Insert elevator pushrod into the hold of quick-controller and tightenclam connectors.
(Remark: The servo should be in center position)
6
18
Apply the foam glue on the joiner of theleft and right wings.
As shown,Apply the foam glue on the plastic part and insert it in the main wing as shown.
As shown,Apply the foam glue on the joiner of the rear landing gear and push it in the position.
As shown,Fix the wing on fuselagewith 6X50mm plastic screw.
As shown,Put the battery in position.
As shown,Connector the aileron servoswith Y wires.
Installing the Battery position.
As shown,Glue left and right main wings together.
As shown, Apply the foam glue to the stuffing foam and insert it into wing as shown.
19 20
THROTTLE
RUDDER
ELEVATOR
AILERONS
airplane action
airplane action
airplane action
airplane action
control plane movement
control plane movement
Aileronmovement
7
STICK OPERATION
MODE 1 MODE 2 MOVEMENT
8
55-60mmCenter of gravity
55-60mmCenter of gravity
55 60
ra- m
rmraavrmr
-of grav
9
ESC-40A Leads with siliconrubber(red/black)
11.1V 2200mAhLi-Po 20C
ESC-40A
ESC-40A
EDF 64
10
5
4 5 6 7
317
265
1721
12
11
2
1
6
8
16 13
1320
10
24
1
19
232425 2627
28
35
2930
31
3233
18
22
3
89
10
How to open canopy
11
Wire lead shorts can cause fire! If you accidentally short the wires, the battery must be placed in a safe area for observation for approximately 15 minutes.
After flight, the battery cool down to ambient temperature before charging.
observation
12
13
Once you have connected the charger to a power source,The red LED will turn on.
Connect the Li-Po battery pack to the charger.When the park is full charged.The
green LED will turn on.
Parts List
Fuselageturbo-01
TransmitterDYT-2002
turbo-02 wing
turbo-04 Elevator turbo-05 EDF SET
turbo-03 Vertical stabilizer
DY-1007 9g ServoDY-3001 quick-controller
DY-6006 11.1V 2200mAh 20C Li-Po Battery
DYA-000X Adaptor
DYE-1002 Balance Charger
DYR-2001 2.4G ReceiverDY-3003 Glue
turbo-14 DECAL 14
DYM-0010 Brushless Motor turbo-07 Plastic Part set
turbo-10 Hardware
DYE-1004 40A ESC
turbo-9 Canopy
turbo-11 Duct
DYAT-008 Servo Horn
turbo-06 Cockpit
turbo-08 Landing gear
turbo-12 6 leaf blades turbo-13 Duct hardware
Related Documents
