Web viewWeak acids contained in sea water will dissolve some types of rock such as chalk or limestone.(ii) Waves also erode rocks and pebbles by attrition. Waves smash rocks and pebbles

1

GCSE- Coastal Landscapes: Complete revision notes A- Processes1a Types of wave: constructive and destructive.•          Describe the characteristics of the two wave types.•         Explain their impact on beach profiles.

The differences between destructive waves and constructive wavesDestructive waves Constructive waves

Wave height High > 1m Low < 1 mWave energy High LowWave frequency High > 10 per minute Low < than 10 per minuteSwash-Backwash Backwash > Swash Swash > BackwashMain process Erosion Deposition

Outline the characteristics features of a destructive wave, You may use a diagram in your answer. (4)high frequency 10-14 per minute, short wave length, plunging, high energy/above 1m/backwash>swash (1) therefore beaches eroded (1) High energy waves (1)

Compare the characteristics of constructive and destructive waves. (4) Destructive waves have a greater backwash than swash (1) compared to constructive waves due to their higher energy (1) meaning that they can erode beaches (1). Constructive waves have a lower frequency (1) as a result of their longer wavelength (1) Destructive waves are plunging whereas constructive are surging (1). Destructive waves are higher (>1m) compared with constructive (1).

2

Outline the characteristics features of a constructive wave. You may use a diagram in your answer. (4)

Explain the impact of waves on beach profiles.

Constructive waves Destructive wavesProcess Greater swash than backwash. Sand and shingle 

moved up the beach = depositionGreater backwash than swash. Most material is carried downward by the backwash= erosion

Impact on beach profile

Sediment is being added to the beach which the backwash cannot entirely remove, producing agentle build-up of beach material. This will increase the gradient of the beach in its lower section. (swash zone)

Due to erosion, beach profile becomes gentler in its lower section. (swash zone)

1b Types of weathering, erosion and mass movement on the coastline.•          Define and explain the different types of weathering, erosion and mass movement.

Four processes of erosion: (i) Three ways that waves erode the coast:Hydraulic action. Air becomes trapped in joints and cracks in the cliff face. When a wave breaks, the trapped air is compressed which weakens the cliff and causes erosion.Abrasion. Bits of rock and sand in waves are flung against the cliff face. Over time they grind down cliff surfaces like sandpaper.Solution. Weak acids contained in sea water will dissolve some types of rock such as chalk or limestone.(ii) Waves also erode rocks and pebbles by attrition. Waves smash rocks and pebbles on the shore into each other, and they break and become smaller and smoother.Three processes of weathering:

3

Explain the process of physical weathering. (3)Freeze thaw – diurnal changes in temperature around 0 degrees (1). Water in crack widened due to freezing (1), 9% volume increase (1) thawing leaves crack prized open – removes water (1), process repeats (1)

Two processes of mass movement:Explain the process of soil creep. (3)

Outline the process of slumpig. (2)Slumping - a rotational movement of land at the coast (1), triggered by saturation (1)

4

State one impact of slumping on the coast. (1)Loss of land (1) Destruction of property/infrastructure (1)Loss of animal habitats (1) Causes coastal recession (1)Outline how mass movement impacts on coastal landforms. (3)Wave action/sea/rain can cause the cliffs to become saturated (1), if made of clay (1).Over time the material in the cliff becomes weakened and subject to gravity (1) cliff material slides down thereby removing material (1). Landslides can cause rapid removal of coastal material / loss of land (1).Soil creep causes slow removal of soil from coastal slopes (1); ridges / ripples are left (1).Slumping causes a downward moment of material (1) this leaves a curved shape (1).

B- Landforms of erosion and deposition•          Describe the named landforms.•          Explain their formation in terms of sequence and the processes involved, including the influence of vegetation and geology.1- Landforms of erosion: cliffs and wave-cut platforms, headlands and bays, caves, arches, stacks and stumps.

Explain the formation of cliffs and wave-cut platforms. Use annotated diagram or diagrams in your answer. (4)Cliff formation – sea erodes base of cliff via Hydraulic Action, Abrasion (1). Creation of a wave cut notch and overhang

5

(1) Lack of support (gravity)of overhung cliff creates pressure/cracks and subsequent collapse (1) Action of sea compacting rock into platform which protects coast at low tide (1) Formation of steep cliff which over time recedes (1) Max of three without annotated diagram.

Explain the formation of headlands and bays. You may use a diagram(s) in your answer.(4)Max 3 marks without a process or full sequence. E.g. Differential erosion due to perpendicular geology (reference to hard and soft geology which is perpendicular to the coast). Harder rock is more resistant therefore forms land which sticks out into the sea (headlands).Softer rock is eroded (hydraulic action/abrasion/corrosion) at a quicker rate to form a bay. An extension to sequence could refer to development of headlands into stacks/stumps or beaches within bays.

Explain the formation of a stack. You may use a diagram(s) in your answer. (4)E.g. Stacks begin as part of an eroding headland. Wave refraction causes waves to attack the side of the headland. Joints are exploited by erosion (named process e.g. hydraulic action, corrasion). Repeated erosion causes a cave, which becomes eroded through to become an arch. Pressure on the arch and force of gravity ultimately cause the collapse of the arch, leaving a stack.

6

2- What is the process of longshore drift? The impact of longshore drift•          Describe the process of longshore drift.•          Explain the impact on the coastline in terms of landforms and related issues, e.g. deposition in estuaries.

Outline the process of longshore drift. (3)Longshore drift is the movement of material along the beach (1). It occurs in the direction of the prevailing waves (1). It is comprised of swash – where breaking waves move material up a beach (in the direction of prevailing wind/waves (1), and backwash – where (due to gravity) material is dragged back towards the sea (1). Swash and backwash is repeated leading to movement in a zig-zag movement along beach (1). 

7

Explain the impact of longshore drift on the coastline in terms of landforms and related issues, e.g. deposition in estuaries.The movement of materials along the coast:- makes boulders and pebbles smaller and more rounded.- creates landforms such as beaches, spits and bars.- is a problem in river estuaries. Some estuaries which are used to harbour boats have to be constantly dredged because of longshore drift depositing material.Dredging:

3- Landforms of deposition: How are beaches, spits and bars formed?Describe the named landforms and explain their formation in terms of sequence and the processes involved.

Explain the formation of beaches (4)Area of land between the low tide and storm tide marks. Made up of deposited sand and pebbles. Formed by constructive waves. Often in bays, where waves have less energy due to gentle sloping land. Along straight stretches of coastline where longshore drift occurs

Explain the formation of a spit. Use a diagram in your answer. (4)E.g. Spit – Movement of material along a coastline due to longshore drift. Occurs where there is a change in direction of the coastline. Over time build-up of spit as more sediment is deposited offshore. May curve at end due to action of wind/waves. Formation of salt marsh due to spit protecting area from wave action.Max 3 without suitable diagram.

8

See photo of a spit on blog

Explain how the process of longshore drift forms a spit. (3)Explain how a bar is formed. (4)A bar is a long, narrow stretch of pebbles and sand (1) which grows across a bay (1) attached to the land at both ends. (1) It forms when longshore drift occurs on a coastline. (1) When the coastline ends, the sea deposits the material it is transporting because the change in depth affects its ability to transport the material further. (1)If a spit develops in a bay, it may build across it, linking two headlands to form a bar. (1) This is only possible if there is a gently sloping beach (1) and no river entering the sea, (1) because the sand will be removed faster than it can be deposited. (1

C- Coastal Recession1- Differential rates of cliff recession due to factors such as fetch, geology and coastal management.•          Define cliff recession.•          Explain the factors that cause cliff erosion – wave action, weathering and mass movement.

9

Coastal recession: when the coast is eroded and retreats.

Case study: Happisburg (North Norfolk coast)Village of Happisburg (population= 850)Factors which explain high rates of erosion in this area:Geology: Cliff made of soft rock (clay, gravel and sand deposited by glaciers)Lack of Coastal management ('Do nothing' policy)No sea defences: 1958: use of revetments to reduce coastal erosion. From 1995 no repairing of coastal defencesè high rates of erosion.Government has refused to protect the village because it is not cost effective: the village is less valuable than the cost of the defences to protect it.

Explain how the type of rock (geology) and structure can affect the rate of coastal erosion. (4)Rock type - if the cliffs are made from resistant rock, (1) like granite, (1) they will erode more slowly than cliffs made from less resistant rock, (1) such as clay.Rock structure - the rock’s structure can also have an effect on the rate of erosion. Rocks that are well jointed (1) or with many faults, (1) such as limestone, (1) will erode more quickly (1) as the waves exploit these lines of weakness. (1)

Explain the factors affecting the rate of coastal recession. (4)Can refer here to Geology/Fetch/Coastal Management, mass movement. Expect reference to softer geology increases rates of coastal recession (1) due to lower resistance to erosional impact of waves (1) or Increased fetch increases recession (1) due to more distance for greater build-up of wave energy (1).

Suggest how wave fetch can cause different rates of coastal recession. (3)Fetch: The length of water the wind blows over. Longer distance waves have more energy (1), more power to erode (1), increasing hydraulic action/abrasion (1).

2- The effects of coastal recession on people and the environment.•          Describe the effects of coastal recessions on humans, e.g. insurance and loss of homes.•          Describe the effects on the environment, e.g. loss of land.

Effects on people: Case study: Happisburg (North Norfolk coast) Loss of homes: Since 1995: 25 properties and the village’s lifeboat launching station washed away.Loss of value: Houses worth £80,000 when the coast was defended, are now valued at 1£.No insurance of property against coastal erosion.Loss of business: Over the next 100 years: 1400 caravan and chalet parks, six hotels and guest houses. Seven historic buildings and seven golf course holes will be lost to the sea. Effects on the environment: Case study: Durlston BayLoss of land: At Durlston Bay near Swanage the cliff receded 12 metres between 1968 and 1988. In 200/01 severe storms and high energy waves led to a further retreat of another 12 metres.Loss of natural habitats: Durlston County Park also lies on the top and is home to over 250 species of birds that nest on the cliff. These habitats are threatened by cliff recession, which can affect the breeding of rare species such as puffins and falcons.

Explain the effects of coastal recession on people and the environment. Use examples in your answer. (6)A range of specific facts relating to the effects on people and the environment and explained points.Explain how cliff erosion can affect the economy of the local area. (4)Explanation to include four points given from: Loss of property/land (1), increase insurance issues (1), loss of businesses (1), costs of closing beaches (1), any other legitimate explanation (1). Only allow to 4 marks if links to economy (i.e. loss of income or wealth) established.Using examples, explain how coastal recession affects the human environment. (6) 

10

D- Coastal flooding: Prediction and prevention of the effects of coastal flooding by forecasting, building design, planning and education.•          Briefly consider what coastal flooding is and what causes it. Factors which increase vulnerability•          Identify how the effects of coastal flooding are reduced through planning before the event

1- Briefly consider what coastal flooding is and what causes it. Factors which increase vulnerability

Coastal flooding occurs when normally dry, low-lying land is flooded by sea water.- Causes of coastal flooding:Severe weather: Strong winds and storms which can increase the height of waves and tides. Storm surge: A storm surge is an offshore rise of water associated with a low pressure weather system*, typically tropical cyclones. Storm surges are caused by high winds pushing on the ocean's surface. The wind causes the water to pile up higher than the ordinary sea level.*A low-pressure area, low or depression, is a region where the atmospheric pressure is lower than that of surrounding locationsSea level rise: Coastal flooding associated with sea level rise will become a significant issue into the next 100 years.- Factors which increase vulnerabilityTides, low-lying land, and property built on low-lying land.

2- Prediction and prevention of the effects of coastal flooding by forecasting, building design, planning and education.ForecastingUK (HIC): The Met Office predicts (forecasts) the likelihood of a flood. The information gets to householders through weather forecasts and news broadcasts on the TV and radio. It is also on their website.The Environment Agency monitors sea conditions 24 hours a day, 365 days a year. Forecasts of coastal flooding are provided on a 24-hour Flood hotline.Bangladesh (LIC): The Meteorological Department has three radar stations that transmit weather updates. The Bangladesh Disaster Bureau also issues cyclone alerts through the national media as soon as a cyclone is detected by satellites.Coastal flooding can be predicted. Justify this statement. (3)As well as the monitoring which is being done by the Met Office, the Environment Agency also monitors sea conditions over a 24 hour period, 365 days a year. The Storm Tide Forecasting Service provides the Environment Agency with forecasts of coastal flooding which the Environment Agency communicates to the public via their website or phone linePlanningUK: Before building takes place a full check must be made to ensure that the area is not prone to flooding. Planning permission will not be granted if it is.The Thames Flood Barrier was completed in 1982. However, new flood walls along the river and many other flood defence techniques will be installed to protect the London area against flooding.(See photo of the Thames Flood Barrier on blog)Bangladesh:  The Coastal Embankment project has led to the building of 12 sea-facing flood walls and 500 flood shelters.Explain how coastal flooding can be reduced through planning (4)Planning: Not allowing homes to be built in potential flood-risk zones. Reference to government planning laws. DEFRA to decide which areas of coast need planning to prevent areas at most risk therefore reduce the impacts of flooding.

Building designBangladesh: All one-storey or two-storey buildings must have an external staircase to the roof.Malibu (California): Houses are built on stilts to protect them from storm tides.Houses should minimise penetration from wind, rain and storms.

Describe how building design can reduce the effects of coastal flooding. Use examples in your answer. (4)Building design – homes on stilts, waterproofing measures Planning – land use zoning; allow reference to defence if linked to planning, evacuation (e.g. monitoring by Environment Agency). Allow forecasting as part of planning. E.g. In

11

LICs coastal homes in areas prone to flooding are designed with stilts (1). Therefore when flooding occurs possessions are not destroyed as the water is able to pass below the home (1).

Explain how education can reduce the effects of coastal flooding. Use examples in your answer. (4)EducationUK: The government gives advice to the public via its website. There is general advice on how to protect their homes from flooding and what to do if a flood occurs. UK: Environmental Agency page: Prepare your property for flooding.Bangladesh is integrating education about disaster preparedness into school curricula for grades three through ten. Schools practice safety programs and drills nationwide in March and October.The country has already had an effective warning system for more than four decades. In 2007 Cyclone Sidr struck Bangladesh and killed about 3,000 people. It was estimated that the cyclone warning system helped saved 100,000 lives.

Explain how the effects of flooding are reduced. Use examples in your answer. (6)Explain how the effects of coastal flooding can be reduced through prediction and prevention. Use examples in your answer. (6)

E- How the coast is managed.1- The types of hard and soft engineering used on the coastline of the UK, and the advantages and disadvantages of these techniques.•          Define hard and soft engineering.•          Describe hard and soft engineering techniques used in the UK, including groynes, sea walls, off-shore reefs, riprap, revetments, beach replenishment, managed retreat and cliff regrading. Advantages and disadvantages of each technique.

Hard engineeringMethod of coastal management which involves major construction work: groynes, sea walls, off-shore reefs, riprap, revetments. Gabions are included in textbook but not in Edexcel syllabus.Method Advantages DisadvantagesSea wallA long concrete barrier built at the base of a cliff. The modern ones have a recurved face.

It protects the base of the cliff against erosion as it reflects and absorbs wave energy. Effective for many years.

Expensive to build and to maintain.Restricts access to the beach.

GroynesWooden, rock or concrete ‘fences’ built across the beach, perpendicular to the coastline

Prevents the movement of beach material along the coast by longshore drift. Sand builds up on one side of the groyne and the beach builds up as a natural defence against erosion and as an attraction for tourists.

Look ugly and do not last very long when they are made of wood as it rots.Sand is prevented from moving along the coast, and places elsewhere may lose their beach and the natural defence it provides.

Off-shore reefs Rock or concrete barriers built on the sea a short distance from the coastline.

Waves break on the barrier before reaching the coast. This reduces erosion. They allow the build-up of sand along the coast and allow a wide beach to develop as wave energy is reduced.

Very expensive to build.May be removed by heavy storms.

Riprap Large boulders of resistant rock placed in front of the cliff.

These absorb wave energy and protect the cliff behind from erosion. Effective for many years.

Can make the beach inaccessible to tourists.As they stil let some wave energy through, they are not effective in storm conditions.

Missing from textbook:Revetments Slatted wooden structures built at 

These absorb and spread wave energy through slats.They do not interfere with 

Regular maintenance is needed.Not effective in storm conditions.

12

the base of the cliff. longshore drift.

Soft engineering: method of coastal management which works with natural processes at work on the coastline and to be unobstructive (unnoticeable) visually. It does not involve major construction: beach replenishment, managed retreat and cliff regrading.Beach replenishment Adding sand and pebbles on a beach.

Looks natural.Provides a beach for tourists.The beach absorbs wave energy and protects the land or buildings behind.

The sea keeps on eroding it away. So it has to be replaced constantly. Disruption for home-owners as large noisy lorries full of sand regularly replenish the beach.

Cliff regrading Making the cliff face longer so that it has a gentle slope to stop it slumping.

This method is relatively cheap.May be covered in ecomatting to encourage vegetation growth. (See Figure)

Not effective alone. Other methods need to be used at the base of the cliff to stop it being eroded.Properties on the cliff may have to be demolished.

Managed retreatAllowing the sea to gradually flood land and erode cliffs.

Natural processes are allowed to happen.Cheap.

Compensation has to be paid.Upsetting for landowners who lose land.

See photos on blog of each method.

Explain how groynes protect cliff from erosion. (3)Groynes prevent longshore drift (1) therefore trapping sediment (1), thereby building a beach (1) This beach will absorb the wave energy and reduce erosion (1)Outline the advantages and disadvantages of soft engineering techniques. (4)Advantages – cheaper than hard engineering (1). More sustainable to environment (1), and does not require quarrying of rock (1). Less visually obtrusive (1). Doesn’t require as much maintenance. Disadvantages – less effective than hard engineering (1) as it does not always stop erosion from occurring (1), cost of maintenance could be high in the long term (1) with repeated outlays due to annual upkeep (1)

Explain the advantages and disadvantages of offshore reefs as a method of coastal defence. (4)Advantages: They do not take up space on the coastline (1) therefore do not directly affect developments (1) They break waves before they reach coast (1) Reduce wave energy before it reaches the coast(1) meaning less need for onshore protection (1) Visually unobtrusive (1) Long lasting / value for money over time (1).Disadvantages: Local residents may be upset during construction (1) The cost of set up is high / maintain (1) They are not always effective in intense storms (1) therefore may need secondary support on the coast (1) There may be environmental concerns / damage habitats / ecosystems (1).

Compare the advantages of types of soft and hard engineering used on the coast. (4)

2- How the coast is managed in a named location.•          Describe how the coast is managed in a named location.•          Consider the costs and benefits of different approaches to protecting the coast in a named location.Case Study Swanage In Dorset on the south coast of EnglandIn Durlston Bay, erosion mainly occurs at one particular point, where there was a major weakness in the resistant limestone rock. There were three methods used to protect the cliffs from erosion (recession): Cliff regrading – extending it forward, making slope longer and less steep. Reduces the risk of mass movement.  Drainage – removing excess water, so slope wasn’t as heavy or lubricated after rain. Reduces the risk of mass movement and freeze-thaw weathering. Rip rap placement – Large boulders at the base of the cliff to resist wave attack and dissipate wave 21energy.

13

Swanage BayThis is a popular recreational area for beach users, diving, fishing and sailing. Erosion occurred along a considerable length of cliff.Sea wall- Built in the 1920s and provided a promenade as well as a barrier to wave attack.Groynes- The most cost effective method was found to be the replacement of the 1930s groynes and replenishment of the beach sediment. A series of mainly timber groynes were installed in the 1930s, and eighteen of them have been replaced in 2005 with new ones. These reduced longshore drift and help make sure that a beach remained in place to absorb the energy of breaking waves.Beach replenishmentIn November of 2005, 90,000 m3 of sand was deposited on the beach. The beach will need to be recharged with around 40,000m3 of sand every 20 years. This works with the groynes to ensure a good size beach. The works were finally completed in June 2006at an estimated cost of £2.2 million.Cliff regarding: A series of steps were made in the cliff to reduce slope angles.

Coastal management issues:1- The potential impact of any coastal defence works on Swanage tourism and the aesthetic and landscape quality of the coastline.2- The cost of protecting the coast3- The efficiency of the methods used: In January 1st, 201 3, Dorset Coastguard have restricted access to Swanage beach and the South West Coastal Paths, after heavy rains over the holiday period caused further mudslides and cliff subsidence in Swanage.

Choose an area of coast you have studied. Explain how this area of coastline has been managed. (6)Good explanation of the chosen methods. Answer has detail of own case study which can be clearly related to the variation of methods used. Well communicated with good use of geographical terminology, spelling, punctuation and grammar.