WCDMA Performance - Radio Access Network KPI Definition Manual for UMTS6_0_V1_1

Product Version: Definition

Huawei Technologies Co. Ltd.

Product Name: Total page

WCDMA Performance - Radio Access Network KPI Definition Manual for

UMTS6.0(V1.1)

For internal use only

2007-1-16

Written: WCDMA&GSM网络

性能研究部

Data: 2007-1-16`

Review: Data:

Review: Data:

Huawei Technologies Co., Ltd.

All rights reserved

WCDMA Performance – Radio Access Network KPI definition Manual

for UMTS5.1 (V1.2)

07-6-12 All rights reserved Page 2 , Total 5

Revision Record

Date Revision

version change Description Author

2007-01 1.0 New document based on the KPI definition manual for UMTS 5.1, according to RNC V18C01B060.

Guanshiguo/liuyingwei

2007-3-27 1.1 Change CDR formula according to CR

NP8004， for RNC V18C02B021 LiuYingwei


for UMTS5.1 (V1.2)


Content

1 Introduction ........................................................................ 7

2 KPI definition template........................................................ 7

3 KPI classification ................................................................ 7

4 Coverage KPIs ................................................................... 9

4.1 Class B - UL Interference Cell Ratio ..................................................................................9

4.2 Class A - Soft Handover Ratio .........................................................................................10

5 Accessibility KPIs ............................................................. 11

5.1 Class B - IU Paging Success Ratio..................................................................................11

5.2 Class A - Radio Access Success Ratio............................................................................11

5.3 Class A - RRC Setup Success Ratio (other)....................................................................12

5.4 Class A - RRC Setup Success Ratio (service).................................................................13

5.5 Class A - AMR RAB Setup Success Ratio.......................................................................13

5.6 Class A - VP RAB Setup Success Ratio ..........................................................................14

5.7 Class A - CS RAB Setup Success Ratio..........................................................................15

5.8 Class A - PS RAB Setup Success Ratio ..........................................................................15

5.9 Class A – HSDPA RAB Setup Success Ratio..................................................................16

5.10 Class A – HSUPA RAB Setup Success Ratio..................................................................16

6 Retainability KPIs ............................................................. 17

6.1 Class A - CS Service Drop Ratio......................................................................................17

6.2 Class A - AMR Call Drop Ratio ........................................................................................18

6.3 Class A - VP Call Drop Ratio............................................................................................18

6.4 Class B - AMR Traffic Drop Ratio.....................................................................................19

6.5 Class B - VP Traffic Drop Ratio........................................................................................19

6.6 Class A - PS Service Drop Ratio......................................................................................20

6.7 Class A – HSDPA Service Drop Ratio .............................................................................21

6.8 Class A – HSUPA Service Drop Ratio .............................................................................21

7 Mobility KPIs .................................................................... 22

7.1 Class A - Soft Handover Success Ratio...........................................................................22

7.2 Class B - Softer Handover Success Ratio .......................................................................23

7.3 Class A – HS-DSCH Service Cell Change Success Rate with SHO（HSDPA to HSDPA）


for UMTS5.1 (V1.2)


23

7.4 Class A - Channel Handover Success Ratio（HSDPA to DCH）...................................24

7.5 Class A - Channel Handover Success Ratio（DCH to HSDPA）...................................24

7.6 Class A - Intra-frequency Hard Handover Success Ratio................................................25

7.7 Class A - Intra-frequency Hard Handover Success Ratio（HSDPA to HSDPA） ..........25

7.8 Class A - Inter-frequency Hard Handover Success Ratio................................................26

7.9 Class A - Inter-frequency Hard Handover Success Ratio（HSDPA to HSDPA） ..........27

7.10 Class A - CS Inter-RAT Handover Success Ratio (WCDMA to GSM) ............................27

7.11 Class A - PS Inter-RAT Handover Success Ratio (WCDMA to GPRS) ..........................28

7.12 Class A - PS Inter-RAT Handover Success Ratio (GPRS to WCDMA) ..........................28

7.13 Class A - HSDPA Inter-RAT Handover Success Rate (WCDMA to GPRS)....................29

7.14 Class B - SRNC Relocation Preparation Success Ratio..................................................30

7.15 Class B - TRNC Relocation Preparation Success Ratio..................................................30

7.16 Class A – E-DCH Soft Handover Success Rate ..............................................................31

7.17 Class A – E-DCH Service Cell Change Success Rate with SHO（HSUPA to HSUPA）

31

7.18 Class A – E-DCH Service Cell Change Success Rate with Inter-HHO（HSUPA to

HSUPA）......................................................................................................................................32

7.19 Class A – E-DCH to DCH Handover Success Rate（Intra Cell）...................................33

7.20 Class A – DCH to E-DCH Handover Success Rate（Intra Cell）...................................33

7.21 Class A – E-DCH to DCH Handover Success Rate（with Inter HHO） .........................34

7.22 Class A – HSUPA Inter-RAT Handover Success Rate (UTRAN to GPRS) ....................34

8 Service Integrity KPIs ....................................................... 35

8.1 Class A - PS Service UL Average Throughput ................................................................35

8.2 Class A - PS Service DL Average Throughput ................................................................36

8.3 Class B - Service UL Average BLER ...............................................................................37

8.4 Class B - DL RLC Average Retransmission Ratio ...........................................................37

8.5 Class B - HSDPA RLC Throughput..................................................................................38

8.6 Class B - HSUPA RLC Throughput..................................................................................39

9 Availability KPIs................................................................ 39

9.1 Class B - Worst Cell Ratio................................................................................................39

9.2 Class B - IU Paging Congestion Ratio .............................................................................40

9.3 Class B - Admission Refused Ratio .................................................................................41

9.4 Class B - Congested Cell Ratio........................................................................................41

9.5 Class B - Unserviceable Cell Ratio ..................................................................................42


for UMTS5.1 (V1.2)


9.6 Class B - Average CPU Load...........................................................................................42

9.7 Class B - IUB Bandwidth Utilizing Ratio...........................................................................43

10 Traffic KPIs....................................................................... 44

10.1 Class A - CS Equivalent Erlang........................................................................................44

10.2 Class A - PS UL Throughput ............................................................................................44

10.3 Class A - PS DL Throughput ............................................................................................45

10.4 Class A - UL Traffic of Typical Radio Bearers..................................................................45

10.5 Class A - DL Traffic of Typical Radio Bearers..................................................................46

10.6 Class A - HSDPA Mean UE Number................................................................................47

10.7 Class A - HSDPA RLC Traffic Volume.............................................................................47

10.8 Class A - HSUPA Mean UE Number................................................................................48

10.9 Class A - HSUPA RLC Traffic Volume.............................................................................48

10.10 Class B - UL Traffic Volume of QoS Classes...................................................................49

10.11 Class B - DL Traffic Volume of QoS Classes...................................................................50

11 ANNEX............................................................................. 50


for UMTS5.1 (V1.2)


HUAWEI RAN KPI for Performance Management

Key words: RAN, KPI, Performance Management Abstract: This document is a contribution to the RAN KPIs on RNC performance statistics. The document proposes a list of UMTS network level KPIs that should be measured and used to evaluate radio network performance from coverage, accessibility, retainablity, mobility, quality and traffic.

List of abbreviations:

Abbreviation Full spelling

PM Performance Management

RAN Radio Access Network

CS Circuit Switched Domain

PS Packet Switched Domain

AMR Adaptive Multi-Ratio

HHO Hard Handover

SHO Soft Handover

SoHO Softer Handover

VP Video Phone

CE Channel Element

UL Uplink

DL Downlink

RTWP Received Total Wideband Power

BLER Block Error Ratio

RAT Radio Access Technology

KPI Key Performance Indicator

DCCC Dynamic Channel Configuration Control

SCCP Signalling Connection Control Part

TRNC Target Radio Network Controller

HSDPA High Speed Downlink Packet Access

HSDSCH High Speed Downlink shared channel


for UMTS5.1 (V1.2)


1 Introduction

The purpose of this document is to specify the RAN KPI definition as well as counters used to calculate the

KPI.

The original KPI definition comes from the experiences of the commercial network management and radio

network optimization. And the KPI definition shall be updated according to the requirement from customers.

2 KPI definition template

The template used to describer the KPI is listed as follows: KPI name (Clause header)

This is a descriptive name of the KPI that is specified. Description

This sub clause contains an explanation of the KPI. Measurement Scope

This sub clause specifies the KPI work scope. If the scope is ‘RNC’, it means that the KPI value shows the

performance on the RAN and the related counters can be gotten from RNC statistic directly. If the scope is ‘Cell’,

it means that KPI value only shows the performance in a cell and the involved counters can be gotten from cell

statistic. Formula

This sub clause contains a formula used to calculate the KPI. Generally the formula consists of several

counters which shall be explained in other sub clause. Associated Counters

This sub clause contains counters that used in the formula. It also contains the description of the counters.

Annex A provides the counter list.

Class

This property is labeled at the KPI name. Class A means the KPI is a basic one, and must be monitored in

M2000. Class B means the KPI is a additional one, it is useful for optimization, and is a optional KPI monitored

in M2000.

3 KPI classification

The KPI can be divided into following classes, and the counters related to the KPI shall be well defined in

the PM system of RNC. Coverage KPIs

UL Interference Cell Ratio

Soft Handover Ratio


for UMTS5.1 (V1.2)


Accessibility KPIs

IU Paging Success Ratio

Radio Access Success Ratio

RRC Setup Success Ratio (other)

RRC Setup Success Ratio (service)

AMR RAB Setup Success Ratio

VP RAB Setup Success Ratio

CS RAB Setup Success Ratio

PS RAB Setup Success Ratio

HSDPA RAB Setup Success Ratio

HSUPA RAB Setup Success Ratio

Retainability KPIs

CS Service Drop Ratio

AMR Call Drop Ratio

VP Call Drop Ratio

AMR Traffic Drop Ratio

VP Traffic Drop Ratio

PS Service Drop Ratio

HSDPA Service Drop Ratio

HSUPA Service Drop Ratio

Mobility KPIs

Soft Handover Success Ratio

Softer Handover Success Ratio

HS-DSCH Service Cell Change Success Rate with SHO（HSDPA to HSDPA）

Channel Handover Success Ratio（HSDPA to DCH）

Channel Handover Success Ratio（DCH to HSDPA）

Intra-frequency Hard Handover Success Ratio

Intra-frequency Hard Handover Success Ratio（HSDPA to HSDPA）

Inter-frequency Hard Handover Success Ratio

Inter-frequency Hard Handover Success Ratio（HSDPA to HSDPA）

CS Inter-RAT Handover Success Ratio (WCDMA to GSM)

PS Inter-RAT Handover Success Ratio (WCDMA to GPRS)

PS Inter-RAT Handover Success Ratio (GPRS to WCDMA)

HSDPA Inter-RAT Handover Success Rate (WCDMA to GPRS)

SRNC Relocation Preparation Success Ratio

TRNC Relocation Preparation Success Ratio

E-DCH Soft Handover Success Rate

E-DCH Service Cell Change Success Rate with SHO（HSUPA to HSUPA）

E-DCH Service Cell Change Success Rate with Inter-HHO（HSUPA to HSUPA）

E-DCH to DCH Handover Success Rate（Intra Cell）

DCH to E-DCH Handover Success Rate（Intra Cell）

E-DCH to DCH Handover Success Rate（with Inter HHO）

HSUPA Inter-RAT Handover Success Rate (UTRAN to GPRS)


for UMTS5.1 (V1.2)


Service Integrity KPIs

PS Service UL Average Throughput

PS Service DL Average Throughput

Service UL Average BLER

Call Setup Delay

DL RLC Average Retransmission Ratio

HSDPA RLC Throughput

Availability KPIs

Worst Cell Ratio

IU Paging Congestion Ratio

Admission Refused Ratio

Congested Cell Ratio

Unserviceable Cell Ratio

Average CPU Load

IUB Bandwidth Utilizing Ratio

Traffic KPIs

CS Equivalent Erlang

PS UL Throughput

PS DL Throughput

UL Traffic of Typical Radio Bearers

DL Traffic of Typical Radio Bearers

HSDPA Mean UE Number

HSDPA RLC Traffic Volume

HSUPA Mean UE Number

UL Throughput of QoS Classes

DL Throughput of QoS Classes

4 Coverage KPIs

4.1 Class B - UL Interference Cell Ratio

4.1.1 Description

This KPI can be used to evaluate how serious the UL capacity is limited by the UL interference

of all cells in one RNC.

4.1.2 Definition

Table1 UL Interference Cell Ratio


for UMTS5.1 (V1.2)


KPI Name UL Interference Cell Ratio

Measurement Scope

RNC

Formula %10098 ,×

−>=

sInRNCmberOfCellTheTotalNudBmMeanRTWPWhichfCellsTheNumberOULIR

Associated Counters

See ANNEX

Notes -98dBm is refered by the experience from commercial network

4.2 Class A - Soft Handover Ratio

4.2.1 Description

This KPI can be used to evaluate the consumption to network resources due to soft handover in

one RNC.

4.2.2 Definition

Table2 Soft Handover Ratio

KPI Name Soft Handover Ratio

Measurement Scope

RNC

Formula %1001111

312111×

−

++×+×+×

=CBA

CBASHR

A1: RLhberOfUEWitN 1um

B1: RLhberOfUEWitN 2um Associated Counters

C1: RLhberOfUEWitN 3um

Notes None


for UMTS5.1 (V1.2)


5 Accessibility KPIs

Accessibility is the ability of a user to obtain requested service from the system. RRC

connecting and RAB setupping are the mainly procedures of accessibility. These metric can be

calculated per cell and per RNC, and the RNC level KPI is calculated by aggregating all the cell counters

belong the RNC.

5.1 Class B - IU Paging Success Ratio

5.1.1 Description

This KPI can be used to evaluate the success response to the paging from the core network in

one RNC. However the lower paging success ratio does not always mean the lower paging

response, because it may be caused by the unnecessary paging messages from the core

network. So it‘s important to analyze the terminated radio access success ratio and the core

network’s paging strategy for further confirmation.

5.1.2 Definition

Table3 IU Paging Success Ratio

KPI Name IU Paging Success Ratio

Measurement Scope

RNC

Formula %100_ ×=temptIUPagingAtccessIUPagingSuSRIUP

Associated Counters

See ANNEX

Notes None

5.2 Class A - Radio Access Success Ratio

5.2.1 Description

A complete call setup procedure contains the RRC, RAB, and Direct Transfer procedure.

Generally only the RRC and the RAB procedure can be observed from RAN and it is usually


for UMTS5.1 (V1.2)


assumed that there is no error occurred when RAN handling the direct transfer messages. That

is the authentication procedure will be considered to be performed successfully.

This KPI can be used to evaluate the radio access success ratio in one RNC and the access

failures caused by the SCCP congestion are not considered in this call setup procedure.

5.2.2 Definition

Table4 Radio Access Success Ratio

KPI Name Radio Access Success Ratio

Measurement Scope

RNC、Cell

Formula %100)(__ Service ××=AttemptPSRABSetupAttemptCSRABSetupSuccessPSRABSetupSuccessCSRABSetupSRRRCSSRRA

＋

＋

Associated Counters

See ANNEX（Cell）、RRCS_SRservice

Notes RNC level KPI is calculated by aggregating all the cell counters

5.3 Class A - RRC Setup Success Ratio (other)

5.3.1 Description

The RRC setup prcedure is trigged by different reasons, which can be devided into two classes,

the related service and other reasons.

This KPI can be used to evaluate the RRC setup success ratio, which does not include the

service causes in one RNC.

5.3.2 Definition

Table5 RRC Setup Success Ratio (other)

KPI Name RRC Setup Success Ratio (other)

Measurement Scope

RNC、Cell

Formula %100_ other ×=other

other

ionAttemptRRCConnectionSuccessRRCConnectSRRRCS


for UMTS5.1 (V1.2)


Associated Counters

See ANNEX(Cell)


5.4 Class A - RRC Setup Success Ratio (service)

5.4.1 Description

This KPI can be used to evaluate the RRC setup success ratio, which only includes the service

causes in one RNC.

5.4.2 Definition

Table6 RRC Setup Success Ratio (service)

KPI Name RRC Setup Success Ratio (service)

Measurement Scope

RNC、Cell

Formula %100_ Service ×=service

service


Associated Counters

SeeANNEXCell


5.5 Class A - AMR RAB Setup Success Ratio

5.5.1 Description

This KPI can be used to evaluate the RAB setup success ratio of AMR service in one RNC,

which can’t be used to evaluate the AMR call setup success ratio unless the related RRC

procedures of all AMR services are successful.

5.5.2 Definition

Table7 AMR RAB Setup Success Ratio


for UMTS5.1 (V1.2)


KPI Name AMR RAB Setup Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=pAttemptAMRRABSetupSuccessAMRRABSetuSRAMRRABS

Associated Counters

See ANNEXCell


5.6 Class A - VP RAB Setup Success Ratio

5.6.1 Description

This KPI can be used to evaluate the RAB setup success ratio of VP service in one RNC, which

can’t be used to evaluate the VP call setup success ratio unless the related RRC procedures of

VP service are successful.

5.6.2 Definition

Table8 VP RAB Setup Success Ratio

KPI Name VP RAB Setup Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=AttemptVPRABSetupSuccessVPRABSetupSRVPRABS

Associated Counters

See ANNEXCell



for UMTS5.1 (V1.2)


5.7 Class A - CS RAB Setup Success Ratio

5.7.1 Description

This KPI can be used to evaluate the RAB setup success ratio of all CS service in one RNC.

5.7.2 Definition

Table9 CS RAB Setup Success Ratio

KPI Name CS RAB Setup Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=AttemptCSRABSetupSuccessCSRABSetupSRCSRABS

Associated Counters

See ANNEXCell


5.8 Class A - PS RAB Setup Success Ratio

5.8.1 Description

This KPI can be used to evaluate the RAB setup success ratio of all PS service in one RNC.

5.8.2 Definition

Table10 PS RAB Setup Success Ratio

KPI Name PS RAB Setup Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=AttemptPSRABSetupSuccessPSRABSetupSRPSRAB

Associated Counters

See ANNEXCell


for UMTS5.1 (V1.2)



5.9 Class A – HSDPA RAB Setup Success Ratio

5.9.1 Description

This KPI can be used to evaluate the RAB setup success ratio of the PS service carried by

HSDPA.

5.9.2 Definition

Table11 HSDPA RAB Setup Success Ratio

KPI Name HSDPA RAB Setup Success Ratio

Measurement Scope

RNC、Cell

Formula %100____ ×=

temptRABSetupAtHSDPAccessRABSetupSuHSDPASRRABHSDPA

Associated Counters

See ANNEX


5.10 Class A – HSUPA RAB Setup Success Ratio

5.10.1 Description

This KPI can be used to evaluate the RAB setup success ratio of the HSUPA service.

5.10.2 Definition

Table12 HSUPA RAB Setup Success Ratio

KPI Name HSUPA RAB Setup Success Ratio

Measurement Scope

RNC、Cell


for UMTS5.1 (V1.2)


Formula %100____ ×=

temptRABSetupAtHSUPAccessRABSetupSuHSUPASRRABHSUPA

Associated Counters

See ANNEX


6 Retainability KPIs

Retainability is defined as the ability of user to retain its requested service for the desired

duration once connected. This metric can be calculated per cell and per RNC. The RNC level

KPIs can be calculated by aggregateing all the cell counters and Iur counters. For the Iur

counters, please refer to ANNEXIur.

6.1 Class A - CS Service Drop Ratio

6.1.1 Description

This KPI can be used to evaluate the call drop ratio of CS service in one RNC. The call drops

will happen due to RNC abnormal release trigged by RAB RELEASE REQUEST or IU

RELEASE REQUEST messsages.

6.1.2 Definition

Table13 CS Service Call Drop Ratio

KPI Name CS Service Drop Ratio

Measurement Scope

RNC、Cell

Formula Cell : %100Re

Re_ ×=

leaseCSRABleasemalCSRABAbnorCDRCS

Associated Counters

See ANNEXCell

Notes The RNC level KPIs can be calculated by aggregateing all the cell

counters and Iur counters.


for UMTS5.1 (V1.2)


6.2 Class A - AMR Call Drop Ratio

6.2.1 Description

This KPI can be used to evaluate the call drop ratio of AMR service in one RNC. The call drops



6.2.2 Definition

Table14 AMR Call Drop Ratio

KPI Name AMR Call Drop Ratio

Measurement Scope

RNC、Cell


Re_ ×=leaseAMRRAB

leasermalAMRRABAbnoCDRAMR

Associated Counters

See ANNEXCell



6.3 Class A - VP Call Drop Ratio

6.3.1 Description

This KPI can be used to evaluate the call drop ratio of VP service in one RNC, which the call

drops happened due to RNC abnormal release trigged by RAB RELEASE REQUEST or IU


6.3.2 Definition

Table15 VP Call Drop Ratio

KPI Name VP Call Drop Ratio

Measurement Scope

RNC、Cell


for UMTS5.1 (V1.2)



Re_ ×=leaseVPRAB

leasemalVPRABAbnorCDRVP

Associated Counters

See ANNEXCell



6.4 Class B - AMR Traffic Drop Ratio

6.4.1 Description

This KPI can be used to evaluate the traffic per call drop of AMR service in one RNC in terms of

the experience of GSM network management.

6.4.2 Definition

Table16 AMR Traffic Drop Ratio

KPI Name AMR Traffic Drop Ratio

Measurement Scope

RNC、Cell

Formula leasermalAMRRABAbno

AMRTrafficTDRAMRRe60_ ×

=

Associated Counters

See ANNEXRNC、ANNEXCell

Notes Unit: minute

6.5 Class B - VP Traffic Drop Ratio

6.5.1 Description

This KPI can be used to evaluate the traffic per call drop of VP service in one RNC.


for UMTS5.1 (V1.2)


6.5.2 Definition

Table17 VP Traffic Drop Ratio

KPI Name VP Traffic Drop Ratio

Measurement Scope

RNC、Cell

Formula leasemalVPRABAbnor

VPTrafficTDRVPRe60_ ×

=

Associated Counters


Notes Unit: minute

6.6 Class A - PS Service Drop Ratio

6.6.1 Description

This KPI can be used to evaluate the call drop ratio of all PS service in one RNC, which the call



6.6.2 Definition

Table18 PS Service Drop Ratio

KPI Name PS Service Drop Ratio

Measurement Scope

RNC、Cell


Re_ ×=leasePSRAB

leasemalPSRABAbnorCDRPS

Associated Counters

See ANNEXCell




for UMTS5.1 (V1.2)


6.7 Class A – HSDPA Service Drop Ratio

6.7.1 Description

This KPI can be used to evaluate the call drop ratio of PS service carried by HSDPA in one cell,

which the call drops happened due to RNC abnormal release trigged by RAB RELEASE

REQUEST or IU RELEASE REQUEST messsages.

6.7.2 Definition

Table19 HSDPA Service Drop Ratio

KPI Name HSDPA Service Drop Ratio

Measurement Scope

RNC、Cell

Formula %100Re_

Re__ ×=leaseRABHSDPA

leaselRABAbnormaHSDPACDRHSDPA

Associated Counters

See ANNEX


counters.

6.8 Class A – HSUPA Service Drop Ratio

6.8.1 Description

This KPI can be used to evaluate the call drop ratio of PS service carried by HSUPA in one cell,



6.8.2 Definition

Table20 HSUPA Service Drop Ratio

KPI Name HSUPA Service Drop Ratio

Measurement RNC、Cell


for UMTS5.1 (V1.2)


Scope

Formula %100Re_

Re__ ×=leaseRABHSUPA

leaselRABAbnormaHSUPACDRHSUPA

Associated Counters

See ANNEX


counters.

7 Mobility KPIs

7.1 Class A - Soft Handover Success Ratio

7.1.1 Description

This KPI can be used to evaluate the soft handover success ratio in one RNC, which includes

softer handover.

7.1.2 Definition

Table21 Soft Handover Success Ratio

KPI Name Soft Handover Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=mptSHOASUAtteessSHOASUSuccSRSHO

Associated Counters


Notes None


for UMTS5.1 (V1.2)


7.2 Class B - Softer Handover Success Ratio

7.2.1 Description

This KPI can be used to evaluate the softer handover success ratio in one RNC.

7.2.2 Definition

Table22 Softer Handover Success Ratio

KPI Name Softer Handover Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=emptSoHOASUAttcessSoHOASUSucSRSoHO

Associated Counters


Notes None

7.3 Class A – HS-DSCH Service Cell Change Success Rate with SHO（HSDPA

to HSDPA）

7.3.1 Description

This KPI can be used to evaluate the soft handover success ratio of HSDPA service in a cell.

7.3.2 Definition


KPI Name Soft Handover Success Ratio（HSDPA to HSDPA）

Measurement Scope

Cell

Formula %100×=empNumHtoHSHOAttcessNumHtoHSHOSuccessRatioHtoHSHOSuc


for UMTS5.1 (V1.2)


Associated Counters

See ANNEX

Notes None

7.4 Class A - Channel Handover Success Ratio（HSDPA to DCH）

7.4.1 Description

This KPI can be used to evaluate the channel handover success ratio when UE handover from

HSDPA to DCH in a cell.

7.4.2 Definition

Table24 Channel Handover Success Ratio (H to D)

KPI Name Channel Handover Success Ratio（HSDPA to DCH）

Measurement Scope

Cell

Formula %100×=mpNumHtoRHOAtteessNumHtoRHOSuccessRatioHtoRHOSucc

Associated Counters

See ANNEX

Notes None

7.5 Class A - Channel Handover Success Ratio（DCH to HSDPA）

7.5.1 Description


DCH to HSDPA in a cell.

7.5.2 Definition

Table25 Channel Handover Success Ratio (D to H)

KPI Name Channel Handover Success Ratio（DCH to HSDPA）


for UMTS5.1 (V1.2)


Measurement Scope

Cell

Formula %100×=mpNumRtoHHOAtteessNumRtoHHOSuccessRatioRtoHHOSucc

Associated Counters

See ANNEX

Notes None

7.6 Class A - Intra-frequency Hard Handover Success Ratio

7.6.1 Description

This KPI can be used to evaluate the intra-frequency hard handover success ratio in one RNC.

7.6.2 Definition

Table26 Intra-frequency Hard Handover Success Ratio

KPI Name Intra-frequency Hard Handover Success Ratio

Measurement Scope

RNC

Formula %100_ ×−−

=temptInterHHOAtHHOAttemptccessInterHHOSuHHOSuccessSRIntraHHO

Associated Counters

See ANNEX

Notes None

7.7 Class A - Intra-frequency Hard Handover Success Ratio（HSDPA to

HSDPA）

7.7.1 Description

This KPI can be used to evaluate the intra-frequency hard handover success ratio of HSDPA

service in a cell.


for UMTS5.1 (V1.2)


7.7.2 Definition


KPI Name Intra-frequency Hard Handover Success Ratio（HSDPA to HSDPA）

Measurement Scope

Cell

Formula %100×=mHOAttempNuHtoHIntraH

umHOSuccessNHtoHIntraHatioHOSuccessRHtoHIntraH

Associated Counters

See ANNEX

Notes None

7.8 Class A - Inter-frequency Hard Handover Success Ratio

7.8.1 Description

This KPI can be used to evaluate the inter-frequency hard handover success ratio in one RNC.

7.8.2 Definition

Table28 Inter-frequency Hard Handover Success Ratio

KPI Name Inter-frequency Hard Handover Success Ratio

Measurement Scope

RNC

Formula %100_ ×=temptInterHHOAtccessInterHHOSuSRInterHHO

Associated Counters

See ANNEX

Notes None


for UMTS5.1 (V1.2)


7.9 Class A - Inter-frequency Hard Handover Success Ratio（HSDPA to

HSDPA）

7.9.1 Description

This KPI can be used to evaluate the inter-frequency hard handover success ratio of HSDPA

service in a cell.

7.9.2 Definition


KPI Name Inter-frequency Hard Handover Success Ratio（HSDPA to HSDPA）

Measurement Scope

Cell

Formula %100×=mHOAttempNuHtoHInterH

umHOSuccessNHtoHInterHatioHOSuccessRHtoHInterH

Associated Counters

See ANNEX

Notes None

7.10 Class A - CS Inter-RAT Handover Success Ratio (WCDMA to GSM)

7.10.1 Description

This KPI can be used to evaluate the CS inter-RAT handover success ratio in one RNC, which

includes handover out from this RNC and handover to this RNC.

7.10.2 Definition

Table30 CS Inter-RAT Handover Success Ratio (WCDMA to GSM)

KPI Name CS Inter-RAT Handover Success Ratio (WCDMA to GSM)

Measurement Scope

RNC、Cell

Formula %100_ ×=HOAttemptCSInterRATHOSuccessCSInterRATSRHOCSInterRAT


for UMTS5.1 (V1.2)


Associated Counters


Notes None

7.11 Class A - PS Inter-RAT Handover Success Ratio (WCDMA to GPRS)

7.11.1 Description

This KPI can be used to evaluate the PS inter-RAT handover success ratio in one RNC, which


7.11.2 Definition

Table31 PS Inter-RAT Handover Success Ratio (WCDMA to GPRS)

KPI Name PS Inter-RAT Handover Success Ratio (WCDMA to GPRS)

Measurement Scope

RNC、Cell

Formula %100_ ×=utHOAttemptOPSInterRATutHOSuccessOPSInterRATSRHOPSInterRAT out

Associated Counters


Notes None

7.12 Class A - PS Inter-RAT Handover Success Ratio (GPRS to WCDMA)

7.12.1 Description



7.12.2 Definition

Table32 PS Inter-RAT Handover Success Ratio (GPRS to WCDMA)


for UMTS5.1 (V1.2)


KPI Name PS Inter-RAT Handover Success Ratio (GPRS to WCDMA)

Measurement Scope

RNC、Cell

Formula %100_ ×=nHOAttemptIPSInterRATnHOSuccessIPSInterRATSRHOPSInterRAT in

Associated Counters


Notes None

7.13 Class A - HSDPA Inter-RAT Handover Success Rate (WCDMA to GPRS)

7.13.1 Description

This KPI can be used to evaluate the HSDPA inter-RAT handover success ratio in one cell,

from WCDMA to GPRS.

7.13.2 Definition


KPI Name HSDPA Inter-RAT Handover Success Ratio (from WCDMA to

GPRS)

Measurement Scope

Cell

Formula %100_ ×=ptRATHOAttemHSDPAInterssRATHOSucceHSDPAInterSRRATHOHSDPAInter

Associated Counters

See ANNEX

Notes None


for UMTS5.1 (V1.2)


7.14 Class B - SRNC Relocation Preparation Success Ratio

7.14.1 Description

This KPI can be used to evaluate the relocation preparation success ratio in one RNC, which

serves as SRNC.

7.14.2 Definition

Table34 SRNC Relocation Preparation Success Ratio

KPI Name SRNC Relocation Preparation Success Ratio

Measurement Scope

RNC

Formula %100PrRe

Re_ ×=ttempteparationAlocationSRNC

ccesslocationSuSRNCSRSRNCRP

Associated Counters

See ANNEX

Notes None

7.15 Class B - TRNC Relocation Preparation Success Ratio

7.15.1 Description


serves as TRNC.

7.15.2 Definition

Table35 TRNC Relocation Preparation Success Ratio

KPI Name TRNC Relocation Preparation Success Ratio

Measurement Scope

RNC

Formula %100PrRe

Re_ ×=ttempteparationAlocationTRNC

ccesslocationSuTRNCSRTRNCRP


for UMTS5.1 (V1.2)


Associated Counters

See ANNEX

Notes None

7.16 Class A – E-DCH Soft Handover Success Rate

7.16.1 Description

This KPI can be used to evaluate the soft handover success ratio of HSUPA service in a cell.

7.16.2 Definition

Table36 E-DCH Soft Handover Success Rate

KPI Name E-DCH Soft Handover Success Rate

Measurement Scope

Cell

Formula %100__ ×=empNumEDCHSHOAttcessNumEDCHSHOSucSRSHOEDCH

Associated Counters

See ANNEX

Notes None

7.17 Class A – E-DCH Service Cell Change Success Rate with SHO（HSUPA to

HSUPA）

7.17.1 Description

This KPI can be used to evaluate the E-DCH service cell change success rate with SHO

procedure in a cell.

7.17.2 Definition

Table37 E-DCH Service Cell Change Success Rate with SHO


for UMTS5.1 (V1.2)


KPI Name E-DCH Service Cell Change Success Rate with SHO（HSUPA to

HSUPA）

Measurement Scope

Cell

Formula %100_______ ×=

tNumSCellChgAtSHOEDCHcNumSCellChgSuSHOEDCHSRSCellChgSHOEDCH

Associated Counters

See ANNEX

Notes None

7.18 Class A – E-DCH Service Cell Change Success Rate with Inter-HHO

（HSUPA to HSUPA）

7.18.1 Description

This KPI can be used to evaluate the E-DCH service cell change success rate with Inter-HHO


7.18.2 Definition

Table38 E-DCH Service Cell Change Success Rate with Inter-HHO

KPI Name E-DCH Service Cell Change Success Rate with Inter-HHO（HSUPA to HSUPA

Measurement Scope

Cell

Formula _______ ×=

tempNumSCellChgAtInterHHOEDCHccessNumSCellChgSuInterHHOEDCHSRSCellChgInterHHOEDCH

Associated Counters

See ANNEX

Notes None


for UMTS5.1 (V1.2)


7.19 Class A – E-DCH to DCH Handover Success Rate（Intra Cell）

7.19.1 Description


E-DCH to DCH in the same cell.

7.19.2 Definition

Table39 E-DCH to DCH Handover Success Rate（Intra Cell）

KPI Name E-DCH to DCH Handover Success Rate（Intra Cell）

Measurement Scope

Cell

Formula %100_______ ×=

mHOAttempNuIntraCellEtoDumHOSuccessNIntraCellEtoDSRHOIntraCellEtoD

Associated Counters

See ANNEX

Notes None

7.20 Class A – DCH to E-DCH Handover Success Rate（Intra Cell）

7.20.1 Description


DCH to E-DCH in the same cell.

7.20.2 Definition

Table40 DCH to E-DCH Handover Success Rate（Intra Cell）

KPI Name DCH to E-DCH Handover Success Rate（Intra Cell）

Measurement Scope

Cell


for UMTS5.1 (V1.2)


Formula %100_______ ×=

mHOAttempNuIntraCellDtoEumHOSuccessNIntraCellDtoESRHOIntraCellDtoE

Associated Counters

See ANNEX

Notes None

7.21 Class A – E-DCH to DCH Handover Success Rate（with Inter HHO）

7.21.1 Description

This KPI can be used to evaluate the channel switch from E-DCH to DCH with inter HHO

procedure.

7.21.2 Definition

Table41 E-DCH to DCH Handover Success Rate（with Inter HHO）

KPI Name E-DCH to DCH Handover Success Rate（with Inter HHO）

Measurement Scope

Cell

Formula %100_ ×=mHOAttempNuEtoDInterH

umHOSuccessNEtoDInterHSRHOEtoDInterH

Associated Counters

See ANNEX

Notes None

7.22 Class A – HSUPA Inter-RAT Handover Success Rate (UTRAN to GPRS)

7.22.1 Description

This KPI can be used to evaluate the HSUPA service Inter-RAT handover success rate from

UTRAN to GPRS.


for UMTS5.1 (V1.2)


7.22.2 Definition

Table42 HSUPA Inter-RAT Handover Success Rate (UTRAN to GPRS)

KPI Name HSUPA Inter-RAT Handover Success Rate (UTRAN to GPRS)

Measurement Scope

Cell

Formula %100_ ×=pNumRATHOAttemHSUPAInterssNumRATHOSucceHSUPAInterSRRATHOHSUPAInter

Associated Counters

See ANNEX

Notes None

8 Service Integrity KPIs

8.1 Class A - PS Service UL Average Throughput

8.1.1 Description

This grouped KPI can be used to evaluate the busy hour UL throughput of PS service in each

cell. According to the experience from commercial network, there are nine services listed in the

following definition.

8.1.2 Definition

Table43 PS Service UL Average Throughput

KPI Name PS Service UL Average Throughput

Measurement Scope

Cell

Formula

ThroughputKULAveragePSStr 64

ThroughputKULAveragePSInter64




for UMTS5.1 (V1.2)



ThroughputKULAveragePSBkg 64

ThroughputKULAveragePSBkg128



Associated Counters

See ANNEX

Notes Unit：kbps

8.2 Class A - PS Service DL Average Throughput

8.2.1 Description

This grouped KPI can be used to evaluate the busy hour DL throughput of PS service in each

cell. According to the experience from commercial network, there are twelve services listed in

the following definition.

8.2.2 Definition

Table44 PS Service DL Average Throughput

KPI Name PS Service DL Average Throughput

Measurement Scope

Cell

Formula

ThroughputKDLAveragePSStr64



ThroughputKDLAveragePSInter 64

ThroughputKDLAveragePSInter128



ThroughputKDLAveragePSBkg 64

ThroughputKDLAveragePSBkg128


for UMTS5.1 (V1.2)




Associated Counters

See ANNEX

Notes Unit：kbps

8.3 Class B - Service UL Average BLER

8.3.1 Description

This grouped KPI can be used to evaluate the UL BLER value of service in each cell. According

to the experience from commercial network, there are three services listed in the following

definition.

8.3.2 Definition

Table45 Service UL BLER

KPI Name Service UL BLER

Measurement Scope

Cell

Formula

AMRULBLER

VPULBLER

KULBLERPS 64

Associated Counters

See ANNEX

Notes None

8.4 Class B - DL RLC Average Retransmission Ratio

8.4.1 Description

This KPI can be used to evaluate the DL RLC average retransmission in one Cell.


for UMTS5.1 (V1.2)


8.4.2 Definition

Table46 DL RLC Average Retransmission Ratio

KPI Name DL RLC Average Retransmission Ratio

Measurement Scope

Cell

Formula %100Re×=

lockAMDLRLCSentBdBlockAMtransmitteDLRLCDLRLCARR

Associated Counters

See ANNEXCell

Notes None

8.5 Class B - HSDPA RLC Throughput

8.5.1 Description

This KPI can be used to evaluate the DL RLC average throughput in one cell.

8.5.2 Definition

Table47 HSDPA RLC Troughput

KPI Name HSDPA RLC Troughput

Measurement Scope

Cell

Formula

Associated Counters

See ANNEX

Notes This KPI should be calculated in busy time


for UMTS5.1 (V1.2)


8.6 Class B - HSUPA RLC Throughput

8.6.1 Description

This KPI can be used to evaluate the UL RLC average throughput in one cell.

8.6.2 Definition

Table48 HSUPA RLC Troughput

KPI Name HSUPA RLC Troughput

Measurement Scope

Cell

Formula

Associated Counters

See ANNEX


9 Availability KPIs

9.1 Class B - Worst Cell Ratio

9.1.1 Description

This KPI can be used to evaluate the effect of cells with poor call drop rate or call setup

success rate to the deteriorating of network performance in one RNC.

9.1.2 Definition

Table49 Worst Cell Ratio

KPI Name Worst Cell Ratio (WCR)

Measurement Scope

RNC


for UMTS5.1 (V1.2)


Formula %100%)321(%)9521( ,×

><=

sInRNCmberOfCellTheTotalNuandBBorandAAwhichfCellsTheNumberOWCR

A1:See AMR RAB Setup Success Ratio

A2:See VP RAB Setup Success Ratio

B1:See AMR Call Drop Ratio

Associated Counters

B2:See VP Call Drop Ratio

Notes

95% and 3% are refered by the experience from commercial

network while the traffic with AMR voice and video phone is

bigger than 0.1 Erlang.

9.2 Class B - IU Paging Congestion Ratio

9.2.1 Description

This KPI can be used to evaluate the consumption of PCCH bandwidth on busy hour within IU

interface.

9.2.2 Definition

Table50 IU Paging Congestion Ratio

KPI Name IU Paging Congestion Ratio

Measurement Scope

RNC、Cell

Formula %100×=temptIUPagingAt

ssIUPagingLoIUPagingCR

Associated Counters


Notes None


for UMTS5.1 (V1.2)


9.3 Class B - Admission Refused Ratio

9.3.1 Description

This KPI can be used to evaluate the admission refused ratio of radio network busy hour in a

cell.

9.3.2 Definition

Table51 Admission Refused Ratio

KPI Name Admission Refused Ratio

Measurement Scope

Cell

Formula %100ReRe

×=questNumsourceTotal

nNumNoAdmissionRatioNoAdmissio

Associated Counters

See ANNEX

Notes None

9.4 Class B - Congested Cell Ratio

9.4.1 Description

This KPI can be used to evaluate the utility ratio of radio network resources on busy hour in one

RNC.

9.4.2 Definition

Table52 Congested Cell Ratio

KPI Name Congested Cell Ratio

Measurement Scope

RNC

Formula %100×=sInRNCmberOfCellTheTotalNu

yHourCellsOnBusfCongestedTheNumberOICR

Associated See ANNEX


for UMTS5.1 (V1.2)


Counters

Notes

yHourCellsOnBusfCongestedTheNumberO is refered by summing up the

number of cells congested in DL or UL radio resources on busy

hour.

9.5 Class B - Unserviceable Cell Ratio

9.5.1 Description

This KPI can be used to evaluate how serious the unserviceable cells cause the degrading of

network performance on busy hour in one RNC.

9.5.2 Definition

Table53 Unserviceable Cell Ratio

KPI Name Unserviceable Cell Ratio

Measurement Scope

RNC

Formula %1000 ,×

>=

sInRNCmberOfCellTheTotalNulTimeCellUnavaiwhichfCellsTheNumberOUCR

Associated Counters

See ANNEX

Notes None

9.6 Class B - Average CPU Load

9.6.1 Description

This KPI can be used to evaluate the consumption of CPU on busy hour in RNC system.

9.6.2 Definition

Table54 Average CPU Load


for UMTS5.1 (V1.2)


KPI Name Average CPU Load

Measurement Scope

RNC

Formula lityMeanCPUUti

Associated Counters

See ANNEX

Notes lityMeanCPUUti is the CPU average load showed by percentage

9.7 Class B - IUB Bandwidth Utilizing Ratio

9.7.1 Description

This grouped KPI can be used to evaluate the ratio of consumption of IUB bandwidth and

configured IUB bandwidth in one NodeB for uplink and downlink on busy hour, for the

consumption of interactive and background service can’t keep the full rate all time on the

configured IUB bandwidth.

9.7.2 Definition

Table55 IUB Bandwidth Utilizing Ratio

KPI Name IUB Bandwidth Utilizing Ratio

Measurement Scope

NodeB

Formula

%100Re

×=uplink

uplinkuplink widthrationBandIUBConfigu

ficalTimeTrafIUBIUBRTUR

%100Re

×=downlink

downlinkdownlink widthrationBandIUBConfigu


Associated Counters

See ANNEX

Notes uplinkwidthrationBandIUBConfigu and downlinkwidthrationBandIUBConfigu

is based on the calculation of the transmission configuration of each


for UMTS5.1 (V1.2)


NodeB in a RNC.

10 Traffic KPIs

10.1 Class A - CS Equivalent Erlang

10.1.1 Description

This KPI can be used to evaluate the equivalent traffic of all CS service of one RNC.

10.1.2 Definition

Table56 CS Equivalent Traffic

KPI Name CS Equivalent Traffic

Measurement Scope

RNC

Formula ntErlCSEquivale

valentErlCSPeakEqui

Associated Counters

See ANNEX

Notes Unit: Erl

10.2 Class A - PS UL Throughput

10.2.1 Description

This KPI can be used to evaluate the UL throughput of all PS service of one RNC.

10.2.2 Definition

Table57 PS UL Throughput


for UMTS5.1 (V1.2)


KPI Name PS UL Throughput

Measurement Scope

RNC

Formula utUlThroughp

ughputUlPeakThro

Associated Counters

See ANNEX

Notes Unit: kbps

10.3 Class A - PS DL Throughput

10.3.1 Description

This KPI can be used to evaluate the DL throughput of all PS service of one RNC.

10.3.2 Definition

Table58 PS DL Throughput

KPI Name PS DL Throughput

Measurement Scope

RNC

Formula utDlThroughp

ughputDlPeakThro

Associated Counters

See ANNEX

Notes Unit: kbps

10.4 Class A - UL Traffic of Typical Radio Bearers

10.4.1 Description

This grouped KPI can be used to evaluate the average UL traffic of typical radio bearers on

busy hour in one RNC, which the meaning of the traffic from the different sevice is different


for UMTS5.1 (V1.2)


despite of in the same unit.

10.4.2 Definition

Table59 UL Traffic of Typical Radio Bearers

KPI Name UL Traffic of Typical Radio Bearers

Measurement Scope

RNC、Cell

Formula ErlKULAMR _2.12

ErlKULCSConv _64

Associated Counters


Notes Unit: Erl

10.5 Class A - DL Traffic of Typical Radio Bearers

10.5.1 Description

This grouped KPI can be used to evaluate the average DL traffic of typical radio bearers on

busy hour in one RNC, which the meaning of the traffic from the different sevice is different in

despite of the same unit.

10.5.2 Definition

Table60 DL Traffic of Typical Radio Bearers

KPI Name DL Traffic of Typical Radio Bearers

Measurement Scope

RNC、Cell

Formula ErlKDLAMR _2.12

ErlKDLCSConv _64

Associated Counters



for UMTS5.1 (V1.2)


Notes Unit: Erl

10.6 Class A - HSDPA Mean UE Number

10.6.1 Description

This grouped KPI can be used to evaluate the average DL traffic of HSDPA service on busy

hour in one Cell.

10.6.2 Definition

Table61 HSDPA mean ue number

KPI Name HSDPA mean ue number

Measurement Scope

Cell

Formula ENumberHSDPAMeanU

Associated Counters

See ANNEX

Notes should be statistic In busy hour

10.7 Class A - HSDPA RLC Traffic Volume

10.7.1 Description

This grouped KPI can be used to evaluate the total traffic volume of HSDPA service in certain

time in one Cell.

10.7.2 Definition

Table62 HSDPA RLC Traffic Volume

KPI Name HSDPA RLC Traffic Volume

Measurement Cell


for UMTS5.1 (V1.2)


Scope

Formula icVolumHSDPATraff

Associated Counters

See ANNEX

Notes Unit: byte

10.8 Class A - HSUPA Mean UE Number

10.8.1 Description

This KPI can be used to evaluate the average UL traffic of HSUPA service in one Cell.

10.8.2 Definition

Table63 HSUPA mean UE number

KPI Name HSUPA mean UE number

Measurement Scope

Cell

Formula ENumberHSUPAMeanU

Associated Counters

See ANNEX

Notes Unit: Erl

10.9 Class A - HSUPA RLC Traffic Volume

10.9.1 Description

This grouped KPI can be used to evaluate the total traffic volume of HSUPA service in certain

time in one Cell.


for UMTS5.1 (V1.2)


10.9.2 Definition

Table64 HSUPA RLC Traffic Volume

KPI Name HSUPA RLC Traffic Volume

Measurement Scope

Cell

Formula

Associated Counters

See ANNEX

Notes Unit: byte

10.10 Class B - UL Traffic Volume of QoS Classes

10.10.1 Description

This grouped KPI can be used to evaluate the cell’s UL traffic volume of QoS classes in one

cell.

10.10.2 Definition

Table65 UL Traffic Volume of QoS Classes

KPI Name UL Traffic Volume of QoS Classes

Measurement Scope

Cell

Formula

umeTrafficVolCellULConv

merafficVoluCellULStrT

lumerTrafficVoCellULInte

merafficVoluCellULBkgT

Associated Counters

See ANNEX

Notes Unit: bit


for UMTS5.1 (V1.2)


10.11 Class B - DL Traffic Volume of QoS Classes

10.11.1 Description

This grouped KPI can be used to evaluate the cell’s DL traffic volume of QoS classes in one

cell.

10.11.2 Definition

Table66 DL Traffic Volume of QoS Classes

KPI Name DL Traffic Volume of QoS Classes

Measurement Scope

Cell

Formula

umeTrafficVolCellDLConv

merafficVoluCellDLStrT

lumerTrafficVoCellDLInte

merafficVoluCellDLBkgT

Associated Counters

See ANNEX

Notes Unit: bit

11 ANNEX

1. Associated Counters

2. Reference Name 3. Associated Counters 4. Specification

5. MeanRTWP go back VS.MeanRTWP

Mean RTWP of a cell, that is, mean

number of the sum of the RTWP

values reported in a certain period

Unit: dBm

6. MeanTCP VS.MeanTCP

Mean TCP of a cell, that is, mean

number of the sum of the TCP


Unit: dBm

7. lTimeCellUnavai go back VS.Cell.UnavailTime.OM Unavailability Duration of a cell


for UMTS5.1 (V1.2)


8. temptIUPagingAt go back VS.RANAP.Paging.Att.Idle

UE Number of Times of Paging Idle UE

9. ccessIUPagingSu VS.RANAP.Paging.Succ.Id

leUE

Successful Number of Times of

Paging Idle UE

VS.RAB.AttEstabCS.Conv

Number of the CS RABs requested to

establish for conversational services

in a cell 10. AttemptCSRABSetup (Cell) go

back VS.RAB.AttEstabCS.Str


establish for streaming services in a

cell

VS.RAB.SuccEstabCS.Co

nv

Number of the CS RABs established

successfully for conversational

services in a cell 11. SuccessCSRABSetup (Cell)

VS.RAB.SuccEstabCS.Str


successfully for streaming services

in a cell

VS.RAB.AttEstabPS.Conv

Number of the PS RABs requested to


in a RNC

VS.RAB.AttEstabPS.Str



cell

VS.RAB.AttEstabPS.Inter


establish for interactive services in a

cell

12. AttemptPSRABSetup (cell) go

back

VS.RAB.AttEstabPS.Bkg


establish for background services in

a cell

VS.RAB.SuccEstabPS.Co

nv

Numbers of PS RABs Established

Successfully on Request in a cell

VS.RAB.SuccEstabPS.Str Numbers of PS RABs Established


VS.RAB.SuccEstabPS.Inte

r



13. SuccessPSRABSetup (cell)

VS.RAB.SuccEstabPS.Bkg Numbers of PS RABs Established


RRC.AttConnEstab.OrgCo

nvCall

Originating Conversational Call in a

cell

RRC.AttConnEstab.OrgStr

Call Originating Streaming Call in a cell

14. serviceionAttemptRRCConnect (C

ell) go back

RRC.AttConnEstab.OrgInt

erCall Originating Interactive Call in a cell


for UMTS5.1 (V1.2)


RRC.AttConnEstab.OrgBk

gCall Originating Background Call in a cell

RRC.AttConnEstab.OgSub

Call

Originating Subscribed traffic Call in a

cell

RRC.AttConnEstab.TmCo

nvCall

Terminating Conversational Call in a

cell

RRC.AttConnEstab.TmStr

Call Terminating Streaming Call in a cell

RRC.AttConnEstab.TmInte

rCall Terminating Interactive Call in a cell

RRC.AttConnEstab.TmBkg

Call Terminating Background Call in a cell

RRC.AttConnEstab.EmgC

all Emergency Call in a cell

RRC.AttConnEstab.Unkno

wn Unknow in a cell

RRC.AttConnEstab.OgHh

PrSig

Originating High Priority Signalling in

a cell

RRC.AttConnEstab.OgLw

PrSig

Originating Low Priority Signalling in a

cell

RRC.AttConnEstab.CallRe

Est

Terminating High Priority Signalling in

a cell

RRC.AttConnEstab.TmHh

PrSig

Terminating Low Priority Signalling in

a cell

RRC.AttConnEstab.TmLw

PrSig Call re-Establishment

RRC.SuccConnEstab.OgC

onvCall


cell

RRC.SuccConnEstab.Org

StrCall Originating Streaming Call in a cell

RRC.SuccConnEstab.OrgIt

rCall Originating Interactive Call in a cell


BkgCall Originating Background Call in a cell


SubCall


cell

RRC.SuccConnEstab.TmC

onvCall


cell

RRC.SuccConnEstab.TmS

trCall Terminating Streaming Call in a cell

15. serviceionSuccessRRCConnect (C

ell)

RRC.SuccConnEstab.TmIt Terminating Interactive Call in a cell


for UMTS5.1 (V1.2)


rCall

RRC.SuccConnEstab.TmB

kgCall Terminating Background Call in a cell

RRC.SuccConnEstab.Emg

Call Emergency Call in a cell

RRC.SuccConnEstab.Unk

own Unknow in a cell

RRC.SuccConnEstab.OgH

hPrSig


a cell

RRC.SuccConnEstab.OgL

wPrSig


cell

RRC.SuccConnEstab.Call

ReEst


a cell

RRC.SuccConnEstab.TmH

hPrSig


a cell

RRC.SuccConnEstab.TmL

wPrSig Call re-establishment in a cell

RRC.AttConnEstab.IRATC

elRes InterRAT cell Reselection in a cell


CO

InterRAT HHO from GPRS to

WCDMA in a cell

RRC.AttConnEstab.Reg Register in a cell

16. otherionAttemptRRCConnect (Ce

ll) go back

RRC.AttConnEstab.Detach Detach in a cell

RRC.SuccConnEstab.IRA

TCelRes InterRAT cell Reselection in a cell


TCCO


WCDMA in a cell

RRC.SuccConnEstab.Reg Register in a cell

17. otherionSuccessRRCConnect (Ce

ll)

RRC.SuccConnEstab.Deta

ch Detach in a cell

18. pAttemptAMRRABSetu (cell) go

back VS.RAB.AttEstab.AMR

Number of AMR Service RABs

requested to establish in a cell

19. pSuccessAMRRABSetu (cell) VS.RAB.SuccEstab.AMR Number of AMR Service RABs

established successfully in a cell

20. AttemptVPRABSetup (cell) go

back VS.RAB.AttEstCS.Conv.64

Number of VP Service RABs


21. SuccessVPRABSetup (cell) VS.RAB.SucEstabCS.Con

v.64



22. ccessRABSetupSuHSDPA _

go back

VS.HSDPA.RAB.SuccEsta

b

Number of RAB successfully

established for PS Service carried


for UMTS5.1 (V1.2)


by HSDPA

23. temptRABSetupAtHSDPA _ VS.HSDPA.RAB.AttEstab

Number of RAB requested to

establish for PS Service carried by

HSDPA

24. ccessRABSetupSuHSUPA _

go back

VS.HSUPA.RAB.SuccEsta

b



by HSUPA

25. temptRABSetupAtHSUPA _ VS.HSUPA.RAB.AttEstab



HSUPA

VS.RAB.Loss.CS.Abnorm :

Numbers of abnormally released

RABs except RF causes in a cell 26. leasemalCSRABAbnor Re (cell)

go back

VS.RAB.Loss.CS.Abnorm

+ VS.RAB.Loss.CS.RF VS.RAB.Loss.CS.RF : Number of

Released RABs Triggered by RNC

due to RF Reason

27. leaseCSRAB Re (cell)

VS.RAB.Loss.CS.RF +


+ VS.RAB.Loss.CS.Norm

VS.RAB.Loss.CS.Norm : Numbers

of Released RABs Triggered by

RNC due to CS Normal Cause in a

cell

28. leasermalAMRRABAbno Re (c

ell) go back VS.RAB.Loss.CS.AMR

Number of released CS AMR service

RABs triggered by RNC in a cell

29. leaseAMRRABRe

VS.RAB.Loss.CS.AMR +

VS.RAB.Loss.CS.Norm.A

MR

VS.RAB.Loss.CS.Norm.AMR :

Numbers of Released RABs

Triggered by RNC due to CS Normal

Cause in a cell(AMR)

30. leasemalVPRABAbnor Re (cell)

go back VS.RAB.Loss.CS.Conv64K

Number of released CS 64 k service


31. leaseVPRAB Re (cell)

VS.Norm.Rel.CS.Conv.RB.

64 +

VS.RAB.Loss.CS.Conv64

K

Numbers of VP Service RABs

released

32. leasemalPSRABAbnor Re (cell)

go back

VS.RAB.Loss.PS.RF +

VS.RAB.Loss.PS.Abnorm

VS.RAB.Loss.PS.RF :

Numbers of Abnormally Released

RABs except RF causes in a cell


for UMTS5.1 (V1.2)


VS.RAB.Loss.PS.Abnorm : Number

of Released RABs triggered by RNC

due to RF reason

33. leasePSRAB Re (cell)

VS.RAB.Loss.PS.RF +


+ VS.RAB.Loss.PS.Norm

VS.RAB.Loss.PS.Norm : Numbers


RNC due to PS Normal Cause in a

cell

VS.HSDPA.RAB.Loss.Abnorm.NonR

F : Number of released PS

service RABs carried by HSDPA

triggered by RNC in a cell, the cause

is not RF. 34. leaselRABAbnormaHSDPA Re_ go back

VS.HSDPA.RAB.Loss.Abn

orm.NonRF +

VS.HSDPA.RAB.Loss.RF

VS.HSDPA.RAB.Loss.RF :

Number of released PS service

RABs carried by HSDPA triggered

by RNC in a cell, the cause is RF.

VS.HSDPA.RAB.Loss.Norm :


RABs carried by HSDPA

triggered ,the cause is normal.

35. leaseRABNormalHSDPA Re_

VS.HSDPA.RAB.Loss.Nor

m +

VS.HSDPA.RAB.Loss.InAc

tivity

VS.HSDPA.RAB.Loss.InActivity :



triggered ,the cause is User

Inactivity.

36. leaselRABAbnormaHSUPA Re_go back

VS.HSUPA.RAB.Loss.Abn

orm

VS.HSUPA.RAB.Loss.Abnorm:

Number of abnormal released PS

service RABs carried by HSUPA

triggered by RNC in a cell,

37. leaseRABNormalHSUPA Re_

VS.HSUPA.RAB.Loss.Nor

m

VS.HSUPA.RAB.Loss.Norm :


RABs carried by HSUPA


38. mptSHOASUAtte go back VS.SHO.Att.RNC The number of attempts of soft

handovers in a RNC

39. essSHOASUSucc VS.SHO.Succ The number of successful soft

handovers in a RNC

40. mptSHOASUAtte (cell) go back SHO.AttRLAddUESide The number of attempts of soft


for UMTS5.1 (V1.2)


handover added cell in a cell

SHO.AttRLDelUESide The number of attempts of soft

handover deleted cell in a cell

SHO.SuccRLAddUESide The number of successful soft

handovers added cell in a cell 41. essSHOASUSucc (cell)

SHO.SuccRLDelUESide The number of successful soft

handovers deleted cell in a cell

42. emptSoHOASUAtt go back VS.SoHO.ASU.AttRNC The number of attempts of softer

handovers in a RNC

43. cessSoHOASUSuc VS.SoHo.Succ The number of successful softer

handovers in a RNC

VS.SoHO.ASU.AttRLAdd The number of attempts of softer

handover added cell in a cell 44. emptSoHOASUAtt (cell) go back

VS.SoHO.ASU.AttRlDel The number of attempts of softer


VS.SoHO.ASU.SuccRLAdd

The number of successful softer

handovers added cell in a cell 45. cessSoHOASUSuc (cell)

VS.SoHO.ASU.SuccRlDel The number of successful softer


46. empNumHtoHSHOAtt go back VS.HSDPA.CellChg.AttOut

IntraRNC

Num of Service cell change attempts

from HSDPA cell to HSDPA cell

47. cessNumHtoHSHOSuc VS.HSDPA.CellChg.Succ

OutIntraRNC

Num of Service cell change

successful times from HSDPA cell to

HSDPA cell

48. mpNumHtoRHOAtte go back VS.HSDPA.ChR.HSDSCHt

oDCH.Att

Num of Channel handover requests

from HSDSCH to DCH

49. essNumHtoRHOSucc VS.HSDPA.ChR.HSDSCHt

oDCH

Num of Successful Channel

handovers from HSDSCH to DCH

50. mpNumRtoHHOAtte go back VS.HSDPA.ChR.DCHtoHS

DSCH.Att


from DCH to HSDSCH

51. essNumRtoHHOSucc VS.HSDPA.ChR.DCHtoHS

DSCH


handovers from DCH to HSDSCH

52. cessNumEDCHSHOSuc go

back

VS.HSUPA.EDCH.SHO.Su

cc

Num of successful soft handover for

E-DCH channel, include adding and

deleting E-DCH channel.

53. empNumEDCHSHOAtt VS.HSUPA.EDCH.SHO.Att

Num of soft handover requests for



54. cNumSCellChgSuSHOEDCH __ go back

VS.HSUPA.SHO.ServCell

Chg.Succ

Num of successful E-DCH service cell

change with SHO state


for UMTS5.1 (V1.2)


55. tNumSCellChgAtSHOEDCH __


Chg.Att

Num of E-DCH service cell change

attempt with SHO state

56. SCellChgSuInterHHOEDCH __ go back

VS.HSUPA.HHO.InterFreq

.NoChR.Succ

Times of Success of Edch ServCell

Chg for Interfreq HHO.(Measured for

Source ServCell)

57. SCellChgAtInterHHOEDCH __


.NoChR.Att

Times of Attempt of Edch ServCell


Source ServCell)

58. HOSuccessNIntraCellEtoD __ go back

VS.HSUPA.ChR.IntraCell.

EDCHtoDCH.Succ

the number of Times of Successful

Channel type Switch from Edch to

DCH In a Cell

59. HOAttempNuIntraCellEtoD __


EDCHtoDCH.Att

the number of Times of Attempt


DCH In a Cell

60. HOSuccessNIntraCellDtoE __ go back


DCHtoEDCH.Succ


Channel type Switch from Dch to

EDCH In a Cell.

61. HOAttempNuIntraCellDtoE __


DCHtoEDCH.Att



EDCH In a Cell

62. umHOSuccessNEtoDInterH

go back

VS.HSUPA.ChR.InterFreq.

EDCHtoDCH.Succ

The number of Successful Channel

type Switch from Edch to DCH of

Interfreq HHO.

63. mHOAttempNuEtoDInterH VS.HSUPA.ChR.InterFreq.

EDCHtoDCH.Att

The number of Attempt Channel type

Switch from Edch to DCH of

Interfreq HHO.

64. ssNumRATHOSucceHSUPAInter go back

VS.HSUPA.IRATHO.Succ

OutPSUTRAN

the number of HSUPA User succeed

to SysHo out system.

65. pNumRATHOAttemHSUPAInter

VS.HSUPA.IRATHO.AttOu

tPSUTRAN

the number of Hsupa user attempt to

SysHo out system.

66. HHOAttempt go back VS.HHO.Att.RNC Number of Hard Handover Requests

67. HHOSuccess VS.HHO.Succ.RNC Number of Successful Hard

Handovers

68. mHOAttempNuHtoHIntraH go

back

VS.HSDPA.HHO.AttOutIntr

aRNCIntraFreq

Number of Intra Frequency Hard

Handover Requests of HSDPA

69. umHOSuccessNHtoHIntraH VS.HSDPA.HHO.succOutI

ntraRNCIntraFreq

Number of Successful Intra

Frequency Hard Handovers of

HSDPA

70. temptInterHHOAt go back VS.HHO.InterFreq.Att.RNC Number of Inter-Frequency Hard

Handover Requests


for UMTS5.1 (V1.2)


71. ccessInterHHOSu VS.HHO.InterFreq.Succ.R

NC

Number of Successful

Inter-Frequency Hard Handovers

72. mHOAttempNuHtoHInterH go

back


aRNCInterFreq

Number of Inter Frequency Hard


73. umHOSuccessNHtoHInterH VS.HSDPA.HHO.SuccOutI

ntraRNCInterFreq

Number of Successful Inter


HSDPA

74. HOAttemptCSInterRAT go

back

VS.IRATHO.AttCSOut.RN

C

Number of CS Domain Inter-RAT

Outgoing Handover Attempts

75. HOSuccessCSInterRAT VS.IRATHO.SuccCSOut.R

NC


Outgoing Handover Successes

76. HOAttemptCSInterRAT (cell) go

back IRATHO.AttOutCS



77. HOSuccessCSInterRAT (cell) IRATHO.SuccOutCS Number of CS Domain Inter-RAT


78. utHOAttemptOPSInterRAT go

back

VS.IRATHO.AttPSOutUTR

AN.RNC

Number of PS Domain Inter-RAT

Outgoing Handover Commit Initiated

from RNC

79. utHOSuccessOPSInterRAT VS.IRATHO.SuccPSOutU

TRAN.RNC

Number of Successful PS Domain

Inter-RAT Outgoing Handovers

Initiated by RNC

80. nHOAttemptIPSInterRAT go

back

VS.IRATHO.AttPSInUE.R

NC


Incoming Handovers Initiated by UE

81. nHOSuccessIPSInterRAT VS.IRATHO.SuccPSInUE.

RNC


Inter-RAT Incoming Handovers

Initiated by UE

82. utHOAttemptOPSInterRAT (cel

l) go back IRATHO.AttOutPSUTRAN



from RNC

83. utHOSuccessOPSInterRAT (cel

l)

IRATHO.SuccOutPSUTRA

N



Initiated by RNC


CO 84. nHOAttemptIPSInterRAT (cell)

go back RRC.AttConnEstab.IRATC

elRes



85. nHOSuccessIPSInterRAT (cell) IRATHO.SuccOutPSUE



Initiated by UE

86. ssRATHOSucceHSDPAInter VS.IRATHO.HSDPA.Succ

OutPSUTRAN

Number of Successful HSDPA

Inter-RAT hancovers from WCDMA


for UMTS5.1 (V1.2)


go back to GPRS

87. ptRATHOAttemHSDPAInter VS.IRATHO.HSDPA.AttOu

tPSUTRAN

Attempts number of HSDPA


to GPRS

88. ttempteparationAlocationSRNC PrRe

go back RELOC.AttPrep

Number of Preparations for SRNC

Relocations

RELOC.SuccCS Number of Successful SRNC

Relocation Commits 89. ccesslocationSuSRNC Re

RELOC.SuccPS Number of Successful SRNC

Relocation Commits

VS.TRELOC.AttPrep.UEIn

v

Numbers of Resource Allocations for

TRNC Relocations of Different

Types 90. ttempteparationAlocationTRNC PrRe

go back VS.TRELOC.AttPrep.UEN

onInv



Types

VS.TRELOC.SuccExec.UE

Inv

Numbers of Successful TRNC

Relocations of Different Types 91. ccesslocationSuTRNC Re


NotInv


Relocations of Different Types

92. RLhberOfUEWitN 1um go back VS.SHO.AS.1 Average Number of UEs with One RL

VS.SHO.AS.2Softer Average Number of UEs with Two

RLs Combined 93. RLhberOfUEWitN 2um

VS.SHO.AS.2Soft Average Number of UEs with Two

RLs Uncombined

VS.SHO.AS.3Soft2Softer Average Number of UEs with Three

RLs and Two Combined

VS.SHO.AS.3Soft Average Number of UEs with Three

RLs Uncombined 94. RLhberOfUEWitN 3um

VS.SHO.AS.3Softer Average Number of UEs with Three

RLs Combined

VS.RAC.CodeRejDL Num of Admission refuse because of

no code resource

VS.RAC.NoAdmUL Num of Admission refuse because of

no UL power resource

VS.RAC.NoAdmDL Num of Admission refuse because of

no DL power resource

VS.RRNBCred.EmerCall.R

ej

Num of Admission refuse because of

no CE resource during emergency

call request

95. nNumNoAdmissio go back

VS.RRNBCred.NonEmerC Num of Admission refuse because of


for UMTS5.1 (V1.2)


all.Rej no CE resource during

non-emergency call request

VS.RRIUB.NonEmerCall.R

ej


no IuB resource during


VS.RRIUB.EmerCall.Rej


no IuB resource during emergency

call request

96. questNumsourceTotal ReRe VS.CellResApply.DCH Total num of RNC apply for dedicated

resource for UE

97. lityMeanCPUUti go back VS.MeanCPUUtil.SPU CPU Utilization of WSPU

98. uplinkficrationTrafIUBConfigu VS.QAAL2.AllocedAveBwd

.AAL2BitRate

Average Value of allocated average

AAL2 bit rate in backward direction

99. downlinkficrationTrafIUBConfigu

VS.QAAL2.AllocedAveFwd

.AAL2BitRate


AAL2 bit rate in forward direction

（VS.UNILNK.RXCELLS）

×53×8

Bits Received by UNI Link during a

statistical period 100. uplinkficalTimeTrafIUB Re

（VS.IMAGRP.RXCELLS）

×53×8

Bits Received by IMA Group during a

statistical period

（VS.UNILNK.TXCELLS）

×53×8

Bits Sent by UNI Link during a

statistical period 101. downlinkficalTimeTrafIUB Re

（VS.IMAGRP.TXCELLS）

×53×8

Bits Sent by IMA Group during a

statistical period

VS.CN.Page.Loss.IUFC

Number of Paging Messages

Discarded due to Iu Interface Flow

Control 102. ssIUPagingLo go back

VS.CN.Page.Loss.PCHCo

ng

Number of Paging Messages Lost

due to PCH Congestion

103. ssIUPagingLo (cell) go back VS.RRC.Paging1.Loss.PC

HCong.Cell Discard paging due to congestion

104. temptIUPagingAt (cell) VS.RRC.Paging1.Att.Cell The number of paging sended by a

cell

105. AMRULBLER go back VS.ULBlerAMR UL BLER of AMR Speech Service on

DCH

106. VPULBLER VS.ULBlerCSRT.64 UL BLER of CS 64 K Real-time

Service on DCH

107. KULBLERPS64 VS.ULBlerPSRT.64 UL BLER of PS 64 K Real-time

Service on DCH

108. ThroughputKULAveragePSStr 64 VS.PS.Str.Kbps.UL64 UL Bit Rate of PS 64K Streaming

Traffic


for UMTS5.1 (V1.2)


go back

109. ThroughputKULAveragePSInter64

VS.PS.Int.Kbps.UL64 UL Bit Rate of PS 64K Interactive

Traffic



Traffic



Traffic



Traffic

113. ThroughputKULAveragePSBkg 64

VS.PS.BKG.Kbps.UL64 UL Bit Rate of PS 64K Background

Traffic

114. ThroughputKULAveragePSBkg128


Traffic



Traffic



Traffic

117. ThroughputKDLAveragePSStr64 go back

VS.PS.Str.Kbps.DL64 DL Bit Rate of PS 64K Streaming

Traffic

118. ThroughputKDLAveragePSStr128


Traffic



Traffic

120. ThroughputKDLAveragePSInter 64

VS.PS.Int.Kbps.DL64 DL Bit Rate of PS 64K Interactive

Traffic

121. ThroughputKDLAveragePSInter128


Traffic



Traffic



Traffic

124. ThroughputKDLAveragePSBkg 64

VS.PS.BKG.Kbps.DL64 DL Bit Rate of PS 64K Background

Traffic

125. ThroughputKDLAveragePSBkg128


Traffic

126. ThroughputKDLAveragePSBkg144 VS.PS.BKG.Kbps.DL144 DL Bit Rate of PS 144K Background

Traffic


for UMTS5.1 (V1.2)




Traffic

VS.RLC.AM.Tx.Trf.PDU Total Sended traffic PDU of RLC in

AM model 128. lockAMDLRLCSentB (cell) go

back VS.AM.RLC.Tx.Sig.PDU

Total Sended signaling PDU of RLC

in AM model

VS.RLC.AM.Rtx.Trf.PDU Total Resended traffic PDU of RLC in

AM model 129. dBlockAMtransmitteDLRLC Re

VS.AM.RLC.Rtx.Sig.PDU Total Resended signaling PDU of

RLC in AM model

130. ntErlCSEquivale go back VS.CSLoad.Erlang.Equiv.

RNC

Equivalent Erlang of CS Service of

one RNC in statistical period

131. valentErlCSPeakEqui VS.CSLoad.MaxErlang.Eq

uiv.RNC

Max Equivalent Erlang values of all

services in the CS domain of the

RNC

132. utUlThroughp go back VS.PSLoad.ULThruput.RN

C

UL Throughput of PS Service of one

RNC in statistical period

133. ughputUlPeakThro VS.PSLoad.MaxULThruput

.RNC

Max uplink traffic of all services in the

PS domain of the RNC.

134. utDlThroughp go back VS.PSLoad.DLThruput.RN

C

DL Throughput of PS Service of one


135. ughputDlPeakThro VS.PSLoad.MaxDLThruput

.RNC

Max downlink traffic of all services in

the PS domain of the RNC

136. ErlKULAMR _2.12 go back VS.AMR.RB.UL.12.2 Mean Number of AMR Speech UEs

at 12.2k Bit Rates

137. ErlKULCSConv _64 VS.RB.ULConvCS.64.RNC

Mean Number of RB of CS

Conversational service at UL 64k Bit

Rates

138. ErlKULAMR _2.12 (cell) go back VS.AMR.Ctrl.UL12.2 Mean Number of AMR Speech UEs

at 12.2k Bit Rates

139. ErlKULCSConv _64 (cell) VS.RB.DLConvCS.64



Rates

140. ErlKDLAMR _2.12 go back go

back VS.AMR.RB.DL.12.2

Mean Number of AMR Speech UEs

at 12.2k Bit Rates

141. ErlKDLCSConv _64 go back VS.RB.DLConvCS.64.RNC


Conversational service at DL 64k Bit

Rates

142. ErlKDLAMR _2.12 (cell) go back

go back VS.AMR.Ctrl.DL12.2 Mean number of AMR call in a cell


for UMTS5.1 (V1.2)


143. ErlKULCSConv _64 (cell) go back VS.RB.DLConvCS.64 Mean number of VP call in a cell

144. roughputHSDPARLCTh go

back

VS.HSDPA.MeanChThrou

ghput.TotalBytes

Total bytes transimit in Static. Time of

PS service carrie by HSDPA

145. ENumberHSDPAMeanU go back VS.HSDPA.UE.Mean.Cell Mean UE numer of HSDPA Service in

one cell

146. icVolumHSDPATraff go back VS.HSDPA.MeanChThrou

ghput.TotalBytes

Total Traffic Volume of HSDPA

Service of one cell in a cetain time

147. ENumberHSUPAMeanU go back VS.HSUPA.UE.Mean.Cell

Mean UE numer of HSUPA Service in

one cell

(VS.AMR.Ctrl.DL12.2) ×

12.2K

UL throughput of AMR Speech UEs

at 12.2KBit In a Cell 148. umeTrafficVolCellULConv go

back VS.CS.Conv.DL.64.Thrupu

t

UL throughput of CS 64K Streaming

Service In a Cell（＝DL）

149. merafficVoluCellULStrT VS.PS.Str.UL.64.Thruput UL throughput of PS 64K Streaming

Service In a Cell

VS.PS.Int.UL.64.Thruput UL throughput of PS 64K Interactive

Service In a Cell


Service In a Cell


Service In a Cell



Service In a Cell

VS.PS.bkg.UL.64.Thruput UL throughput of PS 64K Background

Service In a Cell

VS.PS.bkg.UL.128.Thruput UL throughput of PS 128K

Background Service In a Cell



150. merafficVoluCellULBkgT

VS.PS.bkg.UL.384.Thruput ULthroughput of PS 384K


(VS.AMR.Ctrl.UL12.2)×

12.2K

DL throughput of AMR Speech UEs

at 12.2KBit 151. umeTrafficVolCellDLConv go


t

DL throughput of CS 64K

Conversational Service In a Cell

VS.PS.Str.DL.64.Thruput DL throughput of PS 64K Streaming

Service In a Cell


Service In a Cell 152. merafficVoluCellDLStrT


Service In a Cell


for UMTS5.1 (V1.2)


VS.PS.Int.DL.64.Thruput DL throughput of PS 64K Interactive

Service In a Cell


Service In a Cell


Service In a Cell

153. lumerTrafficVoCellDLInte


Service In a Cell

VS.PS.bkg.DL.64.Thruput DL throughput of PS 64K Background

Service In a Cell

VS.PS.bkg.DL.128.Thruput DL throughput of PS 128K




154. merafficVoluCellDLBkgT



155. yHourCellsOnBusfCongestedTheNumberO

go back

VS.LCC.OverCongNumUL

>0 or

VS.LCC.OverCongNumD

L>0

Numbers of UL and DL overload

congestions respectively in a cell.

VS.UNI.Lnk.MeanKbps.Rx

Mean receive rate of a UNI link in a

given measurement period. Unit:

kbps.

VS.IMA.Grp.MeanKbps.Rx

Mean receive rate of an IMA group in

a given measurement period. Unit:

kbps.

156. uplinkficalTimeTrafIUB Re go

back

VS.FraATMUNI.Lnk.Mean

Kbps.Rx

Mean receive rate of a FRA ATM link

in a given measurement period. Unit:

kbps.

VS.UNI.Lnk.MeanKbps.Tx

Mean send rate of a UNI link in a


kbps.

VS.IMA.Grp.MeanKbps.Tx

Mean send rate of an IMA group in a


kbps.

157. downlinkficalTimeTrafIUB Re


Kbps.Tx

Mean send rate of a FRA ATM link in


kbps.

158. leaseNormalAMRIuR Re__

goback

VS.Norm.Rel.CS.AMR.IurL

ink

Numbers of released RABs triggered

by RNC due to normal cause in the

best cell which belongs to the

DRNC, the release causes can be


for UMTS5.1 (V1.2)


the following: Successful Relocation

User Inactivity Normal Release

159. leaseAbnormalAMRIuR Re__

VS.Abnorm.Rel.CS.AMR.I

urLink

Numbers of released RABs Due to

Abnormal causes in the best cell

which belongs to the DRNC.

160. leaseNormalVPIuR Re__ VS.Norm.Rel.CS.Conv.RB.

64.IurLink







161. leaseAbnormalVPIuR Re__ VS.Abnorm.Rel.CS.Conv.

RB.64.IurLink




162. leaseNormalPSRIuR Re_99_

VS.Norm.Rel.PS.BE.RB.0.

32.IurLink +

VS.Norm.Rel.PS.BE.RB.3

2.64.IurLink +


4.144.IurLink +


44.384.IurLink +

VS.Norm.Rel.PS.CCH.Iur

Link +

VS.Abnorm.Rel.PS.BE.R

B.0.32.UeGen.IurLink +






B.144.384.UeGen.IurLink

+

VS.Abnorm.Rel.PS.CCH.

UeGen.IurLink

VS.Norm.Rel.PS.BE.RB.0.32.IurLink


VS.Norm.Rel.PS.BE.RB.64.144.IurLin

k

VS.Norm.Rel.PS.BE.RB.144.384.IurLi

nk

VS.Norm.Rel.PS.CCH.IurLink

: Numbers of released RABs

triggered by RNC due to normal

cause in the best cell which belongs

to the DRNC, the release causes

can be the following: Successful

Relocation User Inactivity Normal

Release.

VS.Abnorm.Rel.PS.BE.RB.0.32.UeG

en.IurLink

VS.Abnorm.Rel.PS.BE.RB.32.64.Ue

Gen.IurLink

VS.Abnorm.Rel.PS.BE.RB.64.144.U

eGen.IurLink

VS.Abnorm.Rel.PS.BE.RB.144.384.

UeGen.IurLink

VS.Abnorm.Rel.PS.CCH.UeGen.Iur

Link


triggered by

"release-due-to-UE-generated-signal

ing-connection-release" in the best


for UMTS5.1 (V1.2)


cell which belongs to the DRNC. For

the PS domain, the cause can

belong to normal release.

163. leaseAbnormalPSRIuR Re_99_

VS.Abnorm.Rel.PS.BE.RB.

0.32.IurLink +


B.32.64.IurLink +


B.64.144.IurLink +


B.144.384.IurLink +

VS.Abnorm.Rel.PS.CCH.I

urLink -


B.0.32.UeGen.IurLink -







-


UeGen.IurLink

VS.Abnorm.Rel.PS.BE.RB.0.32.IurLin

k

VS.Abnorm.Rel.PS.BE.RB.32.64.IurLi

nk

VS.Abnorm.Rel.PS.BE.RB.64.144.Iur

Link

VS.Abnorm.Rel.PS.BE.RB.144.384.Iu

rLink

VS.Abnorm.Rel.PS.CCH.IurLink

: Numbers of released RABs Due to


which belongs to the DRNC

164. go back VS.HSUPA.MeanChThrou

ghput.TotalBytes


PS service carrie by HSUPA


ghput.TotalBytes



Product Version: Definition

Huawei Technologies Co. Ltd.

Product Name: Total page

WCDMA Performance - Radio Access Network KPI Definition Manual for

UMTS6.0 (V1.1)

For internal use only

2007-1-16

Written: WCDMA&GSM PRD Data: 2007-1-16`

Review: Data:

Review: Data:

Huawei Technologies Co., Ltd.

All rights reserved


for UMTS5.1 (V1.2)


Revision Record

Date Revision

version change Description Author

2007-01 1.0 New document based on the KPI definition manual for UMTS 5.1, according to RNC V18C01B060.

Guanshiguo/liuyingwei

2007-3-27 1.1 Change CDR formula according to CR

NP8004， for RNC V18C02B021 LiuYingwei


for UMTS5.1 (V1.2)


Content

1 Introduction ........................................................................ 7

2 KPI definition template........................................................ 7

3 KPI classification ................................................................ 7

4 Coverage KPIs ................................................................... 9

4.1 Class B - UL Interference Cell Ratio ..................................................................................9

4.2 Class A - Soft Handover Ratio .........................................................................................10

5 Accessibility KPIs ............................................................. 11

5.1 Class B - IU Paging Success Ratio..................................................................................11

5.2 Class A - Radio Access Success Ratio............................................................................11

5.3 Class A - RRC Setup Success Ratio (other)....................................................................12

5.4 Class A - RRC Setup Success Ratio (service).................................................................13

5.5 Class A - AMR RAB Setup Success Ratio.......................................................................13

5.6 Class A - VP RAB Setup Success Ratio ..........................................................................14

5.7 Class A - CS RAB Setup Success Ratio..........................................................................15

5.8 Class A - PS RAB Setup Success Ratio ..........................................................................15

5.9 Class A – HSDPA RAB Setup Success Ratio..................................................................16

5.10 Class A – HSUPA RAB Setup Success Ratio..................................................................16

6 Retainability KPIs ............................................................. 17

6.1 Class A - CS Service Drop Ratio......................................................................................17

6.2 Class A - AMR Call Drop Ratio ........................................................................................18

6.3 Class A - VP Call Drop Ratio............................................................................................18

6.4 Class B - AMR Traffic Drop Ratio.....................................................................................19

6.5 Class B - VP Traffic Drop Ratio........................................................................................19

6.6 Class A - PS Service Drop Ratio......................................................................................20

6.7 Class A – HSDPA Service Drop Ratio .............................................................................21

6.8 Class A – HSUPA Service Drop Ratio .............................................................................21

7 Mobility KPIs .................................................................... 22

7.1 Class A - Soft Handover Success Ratio...........................................................................22

7.2 Class B - Softer Handover Success Ratio .......................................................................23

7.3 Class A – HS-DSCH Service Cell Change Success Rate with SHO（HSDPA to HSDPA）


for UMTS5.1 (V1.2)


23

7.4 Class A - Channel Handover Success Ratio（HSDPA to DCH）...................................24

7.5 Class A - Channel Handover Success Ratio（DCH to HSDPA）...................................24

7.6 Class A - Intra-frequency Hard Handover Success Ratio................................................25

7.7 Class A - Intra-frequency Hard Handover Success Ratio（HSDPA to HSDPA） ..........25

7.8 Class A - Inter-frequency Hard Handover Success Ratio................................................26

7.9 Class A - Inter-frequency Hard Handover Success Ratio（HSDPA to HSDPA） ..........27

7.10 Class A - CS Inter-RAT Handover Success Ratio (WCDMA to GSM) ............................27

7.11 Class A - PS Inter-RAT Handover Success Ratio (WCDMA to GPRS) ..........................28

7.12 Class A - PS Inter-RAT Handover Success Ratio (GPRS to WCDMA) ..........................28

7.13 Class A - HSDPA Inter-RAT Handover Success Rate (WCDMA to GPRS)....................29

7.14 Class B - SRNC Relocation Preparation Success Ratio..................................................30

7.15 Class B - TRNC Relocation Preparation Success Ratio..................................................30

7.16 Class A – E-DCH Soft Handover Success Rate ..............................................................31

7.17 Class A – E-DCH Service Cell Change Success Rate with SHO（HSUPA to HSUPA）

31

7.18 Class A – E-DCH Service Cell Change Success Rate with Inter-HHO（HSUPA to

HSUPA）......................................................................................................................................32

7.19 Class A – E-DCH to DCH Handover Success Rate（Intra Cell）...................................33

7.20 Class A – DCH to E-DCH Handover Success Rate（Intra Cell）...................................33

7.21 Class A – E-DCH to DCH Handover Success Rate（with Inter HHO） .........................34

7.22 Class A – HSUPA Inter-RAT Handover Success Rate (UTRAN to GPRS) ....................34

8 Service Integrity KPIs ....................................................... 35

8.1 Class A - PS Service UL Average Throughput ................................................................35

8.2 Class A - PS Service DL Average Throughput ................................................................36

8.3 Class B - Service UL Average BLER ...............................................................................37

8.4 Class B - DL RLC Average Retransmission Ratio ...........................................................37

8.5 Class B - HSDPA RLC Throughput..................................................................................38

8.6 Class B - HSUPA RLC Throughput..................................................................................39

9 Availability KPIs................................................................ 39

9.1 Class B - Worst Cell Ratio................................................................................................39

9.2 Class B - IU Paging Congestion Ratio .............................................................................40

9.3 Class B - Admission Refused Ratio .................................................................................41

9.4 Class B - Congested Cell Ratio........................................................................................41

9.5 Class B - Unserviceable Cell Ratio ..................................................................................42


for UMTS5.1 (V1.2)


9.6 Class B - Average CPU Load...........................................................................................42

9.7 Class B - IUB Bandwidth Utilizing Ratio...........................................................................43

10 Traffic KPIs....................................................................... 44

10.1 Class A - CS Equivalent Erlang........................................................................................44

10.2 Class A - PS UL Throughput ............................................................................................44

10.3 Class A - PS DL Throughput ............................................................................................45

10.4 Class A - UL Traffic of Typical Radio Bearers..................................................................45

10.5 Class A - DL Traffic of Typical Radio Bearers..................................................................46

10.6 Class A - HSDPA Mean UE Number................................................................................47

10.7 Class A - HSDPA RLC Traffic Volume.............................................................................47

10.8 Class A - HSUPA Mean UE Number................................................................................48

10.9 Class A - HSUPA RLC Traffic Volume.............................................................................48

10.10 Class B - UL Traffic Volume of QoS Classes...................................................................49

10.11 Class B - DL Traffic Volume of QoS Classes...................................................................50

11 ANNEX............................................................................. 50


for UMTS5.1 (V1.2)


HUAWEI RAN KPI for Performance Management

Key words: RAN, KPI, Performance Management Abstract: This document is a contribution to the RAN KPIs on RNC performance statistics. The document proposes a list of UMTS network level KPIs that should be measured and used to evaluate radio network performance from coverage, accessibility, retainablity, mobility, quality and traffic.

List of abbreviations:

Abbreviation Full spelling

PM Performance Management

RAN Radio Access Network

CS Circuit Switched Domain

PS Packet Switched Domain

AMR Adaptive Multi-Ratio

HHO Hard Handover

SHO Soft Handover

SoHO Softer Handover

VP Video Phone

CE Channel Element

UL Uplink

DL Downlink

RTWP Received Total Wideband Power

BLER Block Error Ratio

RAT Radio Access Technology

KPI Key Performance Indicator

DCCC Dynamic Channel Configuration Control

SCCP Signalling Connection Control Part

TRNC Target Radio Network Controller

HSDPA High Speed Downlink Packet Access

HSDSCH High Speed Downlink shared channel


for UMTS5.1 (V1.2)


1 Introduction

The purpose of this document is to specify the RAN KPI definition as well as counters used to calculate the

KPI.

The original KPI definition comes from the experiences of the commercial network management and radio

network optimization. And the KPI definition shall be updated according to the requirement from customers.

2 KPI definition template

The template used to describer the KPI is listed as follows: KPI name (Clause header)

This is a descriptive name of the KPI that is specified. Description

This sub clause contains an explanation of the KPI. Measurement Scope

This sub clause specifies the KPI work scope. If the scope is ‘RNC’, it means that the KPI value shows the

performance on the RAN and the related counters can be gotten from RNC statistic directly. If the scope is ‘Cell’,

it means that KPI value only shows the performance in a cell and the involved counters can be gotten from cell

statistic. Formula

This sub clause contains a formula used to calculate the KPI. Generally the formula consists of several

counters which shall be explained in other sub clause. Associated Counters

This sub clause contains counters that used in the formula. It also contains the description of the counters.

Annex A provides the counter list.

Class

This property is labeled at the KPI name. Class A means the KPI is a basic one, and must be monitored in

M2000. Class B means the KPI is a additional one, it is useful for optimization, and is a optional KPI monitored

in M2000.

3 KPI classification

The KPI can be divided into following classes, and the counters related to the KPI shall be well defined in

the PM system of RNC. Coverage KPIs

UL Interference Cell Ratio

Soft Handover Ratio


for UMTS5.1 (V1.2)


Accessibility KPIs

IU Paging Success Ratio

Radio Access Success Ratio

RRC Setup Success Ratio (other)

RRC Setup Success Ratio (service)

AMR RAB Setup Success Ratio

VP RAB Setup Success Ratio

CS RAB Setup Success Ratio

PS RAB Setup Success Ratio

HSDPA RAB Setup Success Ratio

HSUPA RAB Setup Success Ratio

Retainability KPIs

CS Service Drop Ratio

AMR Call Drop Ratio

VP Call Drop Ratio

AMR Traffic Drop Ratio

VP Traffic Drop Ratio

PS Service Drop Ratio

HSDPA Service Drop Ratio

HSUPA Service Drop Ratio

Mobility KPIs

Soft Handover Success Ratio

Softer Handover Success Ratio

HS-DSCH Service Cell Change Success Rate with SHO（HSDPA to HSDPA）

Channel Handover Success Ratio（HSDPA to DCH）

Channel Handover Success Ratio（DCH to HSDPA）

Intra-frequency Hard Handover Success Ratio

Intra-frequency Hard Handover Success Ratio（HSDPA to HSDPA）

Inter-frequency Hard Handover Success Ratio

Inter-frequency Hard Handover Success Ratio（HSDPA to HSDPA）

CS Inter-RAT Handover Success Ratio (WCDMA to GSM)

PS Inter-RAT Handover Success Ratio (WCDMA to GPRS)

PS Inter-RAT Handover Success Ratio (GPRS to WCDMA)

HSDPA Inter-RAT Handover Success Rate (WCDMA to GPRS)

SRNC Relocation Preparation Success Ratio

TRNC Relocation Preparation Success Ratio

E-DCH Soft Handover Success Rate

E-DCH Service Cell Change Success Rate with SHO（HSUPA to HSUPA）

E-DCH Service Cell Change Success Rate with Inter-HHO（HSUPA to HSUPA）

E-DCH to DCH Handover Success Rate（Intra Cell）

DCH to E-DCH Handover Success Rate（Intra Cell）

E-DCH to DCH Handover Success Rate（with Inter HHO）

HSUPA Inter-RAT Handover Success Rate (UTRAN to GPRS)


for UMTS5.1 (V1.2)


Service Integrity KPIs

PS Service UL Average Throughput

PS Service DL Average Throughput

Service UL Average BLER

Call Setup Delay

DL RLC Average Retransmission Ratio

HSDPA RLC Throughput

Availability KPIs

Worst Cell Ratio

IU Paging Congestion Ratio

Admission Refused Ratio

Congested Cell Ratio

Unserviceable Cell Ratio

Average CPU Load

IUB Bandwidth Utilizing Ratio

Traffic KPIs

CS Equivalent Erlang

PS UL Throughput

PS DL Throughput

UL Traffic of Typical Radio Bearers

DL Traffic of Typical Radio Bearers

HSDPA Mean UE Number

HSDPA RLC Traffic Volume

HSUPA Mean UE Number

UL Throughput of QoS Classes

DL Throughput of QoS Classes

4 Coverage KPIs

4.1 Class B - UL Interference Cell Ratio

4.1.1 Description

This KPI can be used to evaluate how serious the UL capacity is limited by the UL interference

of all cells in one RNC.

4.1.2 Definition

Table1 UL Interference Cell Ratio


for UMTS5.1 (V1.2)


KPI Name UL Interference Cell Ratio

Measurement Scope

RNC

Formula %10098 ,×

−>=

sInRNCmberOfCellTheTotalNudBmMeanRTWPWhichfCellsTheNumberOULIR

Associated Counters

See ANNEX

Notes -98dBm is refered by the experience from commercial network

4.2 Class A - Soft Handover Ratio

4.2.1 Description

This KPI can be used to evaluate the consumption to network resources due to soft handover in

one RNC.

4.2.2 Definition

Table2 Soft Handover Ratio

KPI Name Soft Handover Ratio

Measurement Scope

RNC

Formula %1001111

312111×

−

++×+×+×

=CBA

CBASHR

A1: RLhberOfUEWitN 1um

B1: RLhberOfUEWitN 2um Associated Counters

C1: RLhberOfUEWitN 3um

Notes None


for UMTS5.1 (V1.2)


5 Accessibility KPIs

Accessibility is the ability of a user to obtain requested service from the system. RRC

connecting and RAB setupping are the mainly procedures of accessibility. These metric can be

calculated per cell and per RNC, and the RNC level KPI is calculated by aggregating all the cell counters

belong the RNC.

5.1 Class B - IU Paging Success Ratio

5.1.1 Description

This KPI can be used to evaluate the success response to the paging from the core network in

one RNC. However the lower paging success ratio does not always mean the lower paging

response, because it may be caused by the unnecessary paging messages from the core

network. So it‘s important to analyze the terminated radio access success ratio and the core

network’s paging strategy for further confirmation.

5.1.2 Definition

Table3 IU Paging Success Ratio

KPI Name IU Paging Success Ratio

Measurement Scope

RNC

Formula %100_ ×=temptIUPagingAtccessIUPagingSuSRIUP

Associated Counters

See ANNEX

Notes None

5.2 Class A - Radio Access Success Ratio

5.2.1 Description

A complete call setup procedure contains the RRC, RAB, and Direct Transfer procedure.

Generally only the RRC and the RAB procedure can be observed from RAN and it is usually


for UMTS5.1 (V1.2)


assumed that there is no error occurred when RAN handling the direct transfer messages. That

is the authentication procedure will be considered to be performed successfully.

This KPI can be used to evaluate the radio access success ratio in one RNC and the access

failures caused by the SCCP congestion are not considered in this call setup procedure.

5.2.2 Definition

Table4 Radio Access Success Ratio

KPI Name Radio Access Success Ratio

Measurement Scope

RNC、Cell

Formula %100)(__ Service ××=AttemptPSRABSetupAttemptCSRABSetupSuccessPSRABSetupSuccessCSRABSetupSRRRCSSRRA

＋

＋

Associated Counters

See ANNEX（Cell）、RRCS_SRservice


5.3 Class A - RRC Setup Success Ratio (other)

5.3.1 Description

The RRC setup prcedure is trigged by different reasons, which can be devided into two classes,

the related service and other reasons.

This KPI can be used to evaluate the RRC setup success ratio, which does not include the

service causes in one RNC.

5.3.2 Definition

Table5 RRC Setup Success Ratio (other)

KPI Name RRC Setup Success Ratio (other)

Measurement Scope

RNC、Cell

Formula %100_ other ×=other

other



for UMTS5.1 (V1.2)


Associated Counters

See ANNEX(Cell)


5.4 Class A - RRC Setup Success Ratio (service)

5.4.1 Description

This KPI can be used to evaluate the RRC setup success ratio, which only includes the service

causes in one RNC.

5.4.2 Definition

Table6 RRC Setup Success Ratio (service)

KPI Name RRC Setup Success Ratio (service)

Measurement Scope

RNC、Cell

Formula %100_ Service ×=service

service


Associated Counters

SeeANNEXCell


5.5 Class A - AMR RAB Setup Success Ratio

5.5.1 Description

This KPI can be used to evaluate the RAB setup success ratio of AMR service in one RNC,

which can’t be used to evaluate the AMR call setup success ratio unless the related RRC

procedures of all AMR services are successful.

5.5.2 Definition

Table7 AMR RAB Setup Success Ratio


for UMTS5.1 (V1.2)


KPI Name AMR RAB Setup Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=pAttemptAMRRABSetupSuccessAMRRABSetuSRAMRRABS

Associated Counters

See ANNEXCell


5.6 Class A - VP RAB Setup Success Ratio

5.6.1 Description

This KPI can be used to evaluate the RAB setup success ratio of VP service in one RNC, which

can’t be used to evaluate the VP call setup success ratio unless the related RRC procedures of

VP service are successful.

5.6.2 Definition

Table8 VP RAB Setup Success Ratio

KPI Name VP RAB Setup Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=AttemptVPRABSetupSuccessVPRABSetupSRVPRABS

Associated Counters

See ANNEXCell



for UMTS5.1 (V1.2)


5.7 Class A - CS RAB Setup Success Ratio

5.7.1 Description

This KPI can be used to evaluate the RAB setup success ratio of all CS service in one RNC.

5.7.2 Definition

Table9 CS RAB Setup Success Ratio

KPI Name CS RAB Setup Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=AttemptCSRABSetupSuccessCSRABSetupSRCSRABS

Associated Counters

See ANNEXCell


5.8 Class A - PS RAB Setup Success Ratio

5.8.1 Description

This KPI can be used to evaluate the RAB setup success ratio of all PS service in one RNC.

5.8.2 Definition

Table10 PS RAB Setup Success Ratio

KPI Name PS RAB Setup Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=AttemptPSRABSetupSuccessPSRABSetupSRPSRAB

Associated Counters

See ANNEXCell


for UMTS5.1 (V1.2)



5.9 Class A – HSDPA RAB Setup Success Ratio

5.9.1 Description

This KPI can be used to evaluate the RAB setup success ratio of the PS service carried by

HSDPA.

5.9.2 Definition

Table11 HSDPA RAB Setup Success Ratio

KPI Name HSDPA RAB Setup Success Ratio

Measurement Scope

RNC、Cell

Formula %100____ ×=

temptRABSetupAtHSDPAccessRABSetupSuHSDPASRRABHSDPA

Associated Counters

See ANNEX


5.10 Class A – HSUPA RAB Setup Success Ratio

5.10.1 Description

This KPI can be used to evaluate the RAB setup success ratio of the HSUPA service.

5.10.2 Definition

Table12 HSUPA RAB Setup Success Ratio

KPI Name HSUPA RAB Setup Success Ratio

Measurement Scope

RNC、Cell


for UMTS5.1 (V1.2)


Formula %100____ ×=

temptRABSetupAtHSUPAccessRABSetupSuHSUPASRRABHSUPA

Associated Counters

See ANNEX


6 Retainability KPIs

Retainability is defined as the ability of user to retain its requested service for the desired

duration once connected. This metric can be calculated per cell and per RNC. The RNC level

KPIs can be calculated by aggregateing all the cell counters and Iur counters. For the Iur

counters, please refer to ANNEXIur.

6.1 Class A - CS Service Drop Ratio

6.1.1 Description

This KPI can be used to evaluate the call drop ratio of CS service in one RNC. The call drops



6.1.2 Definition

Table13 CS Service Call Drop Ratio

KPI Name CS Service Drop Ratio

Measurement Scope

RNC、Cell


Re_ ×=

leaseCSRABleasemalCSRABAbnorCDRCS

Associated Counters

See ANNEXCell




for UMTS5.1 (V1.2)


6.2 Class A - AMR Call Drop Ratio

6.2.1 Description

This KPI can be used to evaluate the call drop ratio of AMR service in one RNC. The call drops



6.2.2 Definition

Table14 AMR Call Drop Ratio

KPI Name AMR Call Drop Ratio

Measurement Scope

RNC、Cell


Re_ ×=leaseAMRRAB

leasermalAMRRABAbnoCDRAMR

Associated Counters

See ANNEXCell



6.3 Class A - VP Call Drop Ratio

6.3.1 Description

This KPI can be used to evaluate the call drop ratio of VP service in one RNC, which the call



6.3.2 Definition

Table15 VP Call Drop Ratio

KPI Name VP Call Drop Ratio

Measurement Scope

RNC、Cell


for UMTS5.1 (V1.2)



Re_ ×=leaseVPRAB

leasemalVPRABAbnorCDRVP

Associated Counters

See ANNEXCell



6.4 Class B - AMR Traffic Drop Ratio

6.4.1 Description

This KPI can be used to evaluate the traffic per call drop of AMR service in one RNC in terms of

the experience of GSM network management.

6.4.2 Definition

Table16 AMR Traffic Drop Ratio

KPI Name AMR Traffic Drop Ratio

Measurement Scope

RNC、Cell

Formula leasermalAMRRABAbno

AMRTrafficTDRAMRRe60_ ×

=

Associated Counters


Notes Unit: minute

6.5 Class B - VP Traffic Drop Ratio

6.5.1 Description

This KPI can be used to evaluate the traffic per call drop of VP service in one RNC.


for UMTS5.1 (V1.2)


6.5.2 Definition

Table17 VP Traffic Drop Ratio

KPI Name VP Traffic Drop Ratio

Measurement Scope

RNC、Cell

Formula leasemalVPRABAbnor

VPTrafficTDRVPRe60_ ×

=

Associated Counters


Notes Unit: minute

6.6 Class A - PS Service Drop Ratio

6.6.1 Description

This KPI can be used to evaluate the call drop ratio of all PS service in one RNC, which the call



6.6.2 Definition

Table18 PS Service Drop Ratio

KPI Name PS Service Drop Ratio

Measurement Scope

RNC、Cell


Re_ ×=leasePSRAB

leasemalPSRABAbnorCDRPS

Associated Counters

See ANNEXCell




for UMTS5.1 (V1.2)


6.7 Class A – HSDPA Service Drop Ratio

6.7.1 Description

This KPI can be used to evaluate the call drop ratio of PS service carried by HSDPA in one cell,



6.7.2 Definition

Table19 HSDPA Service Drop Ratio

KPI Name HSDPA Service Drop Ratio

Measurement Scope

RNC、Cell

Formula %100Re_

Re__ ×=leaseRABHSDPA

leaselRABAbnormaHSDPACDRHSDPA

Associated Counters

See ANNEX


counters.

6.8 Class A – HSUPA Service Drop Ratio

6.8.1 Description

This KPI can be used to evaluate the call drop ratio of PS service carried by HSUPA in one cell,



6.8.2 Definition

Table20 HSUPA Service Drop Ratio

KPI Name HSUPA Service Drop Ratio

Measurement RNC、Cell


for UMTS5.1 (V1.2)


Scope

Formula %100Re_

Re__ ×=leaseRABHSUPA

leaselRABAbnormaHSUPACDRHSUPA

Associated Counters

See ANNEX


counters.

7 Mobility KPIs

7.1 Class A - Soft Handover Success Ratio

7.1.1 Description

This KPI can be used to evaluate the soft handover success ratio in one RNC, which includes

softer handover.

7.1.2 Definition


KPI Name Soft Handover Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=mptSHOASUAtteessSHOASUSuccSRSHO

Associated Counters


Notes None


for UMTS5.1 (V1.2)


7.2 Class B - Softer Handover Success Ratio

7.2.1 Description

This KPI can be used to evaluate the softer handover success ratio in one RNC.

7.2.2 Definition

Table22 Softer Handover Success Ratio

KPI Name Softer Handover Success Ratio

Measurement Scope

RNC、Cell

Formula %100_ ×=emptSoHOASUAttcessSoHOASUSucSRSoHO

Associated Counters


Notes None

7.3 Class A – HS-DSCH Service Cell Change Success Rate with SHO（HSDPA

to HSDPA）

7.3.1 Description

This KPI can be used to evaluate the soft handover success ratio of HSDPA service in a cell.

7.3.2 Definition


KPI Name Soft Handover Success Ratio（HSDPA to HSDPA）

Measurement Scope

Cell

Formula %100×=empNumHtoHSHOAttcessNumHtoHSHOSuccessRatioHtoHSHOSuc


for UMTS5.1 (V1.2)


Associated Counters

See ANNEX

Notes None

7.4 Class A - Channel Handover Success Ratio（HSDPA to DCH）

7.4.1 Description


HSDPA to DCH in a cell.

7.4.2 Definition

Table24 Channel Handover Success Ratio (H to D)

KPI Name Channel Handover Success Ratio（HSDPA to DCH）

Measurement Scope

Cell

Formula %100×=mpNumHtoRHOAtteessNumHtoRHOSuccessRatioHtoRHOSucc

Associated Counters

See ANNEX

Notes None

7.5 Class A - Channel Handover Success Ratio（DCH to HSDPA）

7.5.1 Description


DCH to HSDPA in a cell.

7.5.2 Definition

Table25 Channel Handover Success Ratio (D to H)

KPI Name Channel Handover Success Ratio（DCH to HSDPA）


for UMTS5.1 (V1.2)


Measurement Scope

Cell

Formula %100×=mpNumRtoHHOAtteessNumRtoHHOSuccessRatioRtoHHOSucc

Associated Counters

See ANNEX

Notes None

7.6 Class A - Intra-frequency Hard Handover Success Ratio

7.6.1 Description

This KPI can be used to evaluate the intra-frequency hard handover success ratio in one RNC.

7.6.2 Definition


KPI Name Intra-frequency Hard Handover Success Ratio

Measurement Scope

RNC

Formula %100_ ×−−

=temptInterHHOAtHHOAttemptccessInterHHOSuHHOSuccessSRIntraHHO

Associated Counters

See ANNEX

Notes None

7.7 Class A - Intra-frequency Hard Handover Success Ratio（HSDPA to

HSDPA）

7.7.1 Description

This KPI can be used to evaluate the intra-frequency hard handover success ratio of HSDPA

service in a cell.


for UMTS5.1 (V1.2)


7.7.2 Definition


KPI Name Intra-frequency Hard Handover Success Ratio（HSDPA to HSDPA）

Measurement Scope

Cell

Formula %100×=mHOAttempNuHtoHIntraH

umHOSuccessNHtoHIntraHatioHOSuccessRHtoHIntraH

Associated Counters

See ANNEX

Notes None

7.8 Class A - Inter-frequency Hard Handover Success Ratio

7.8.1 Description

This KPI can be used to evaluate the inter-frequency hard handover success ratio in one RNC.

7.8.2 Definition


KPI Name Inter-frequency Hard Handover Success Ratio

Measurement Scope

RNC

Formula %100_ ×=temptInterHHOAtccessInterHHOSuSRInterHHO

Associated Counters

See ANNEX

Notes None


for UMTS5.1 (V1.2)


7.9 Class A - Inter-frequency Hard Handover Success Ratio（HSDPA to

HSDPA）

7.9.1 Description

This KPI can be used to evaluate the inter-frequency hard handover success ratio of HSDPA

service in a cell.

7.9.2 Definition


KPI Name Inter-frequency Hard Handover Success Ratio（HSDPA to HSDPA）

Measurement Scope

Cell

Formula %100×=mHOAttempNuHtoHInterH

umHOSuccessNHtoHInterHatioHOSuccessRHtoHInterH

Associated Counters

See ANNEX

Notes None

7.10 Class A - CS Inter-RAT Handover Success Ratio (WCDMA to GSM)

7.10.1 Description

This KPI can be used to evaluate the CS inter-RAT handover success ratio in one RNC, which


7.10.2 Definition

Table30 CS Inter-RAT Handover Success Ratio (WCDMA to GSM)

KPI Name CS Inter-RAT Handover Success Ratio (WCDMA to GSM)

Measurement Scope

RNC、Cell

Formula %100_ ×=HOAttemptCSInterRATHOSuccessCSInterRATSRHOCSInterRAT


for UMTS5.1 (V1.2)


Associated Counters


Notes None

7.11 Class A - PS Inter-RAT Handover Success Ratio (WCDMA to GPRS)

7.11.1 Description



7.11.2 Definition

Table31 PS Inter-RAT Handover Success Ratio (WCDMA to GPRS)

KPI Name PS Inter-RAT Handover Success Ratio (WCDMA to GPRS)

Measurement Scope

RNC、Cell

Formula %100_ ×=utHOAttemptOPSInterRATutHOSuccessOPSInterRATSRHOPSInterRAT out

Associated Counters


Notes None

7.12 Class A - PS Inter-RAT Handover Success Ratio (GPRS to WCDMA)

7.12.1 Description



7.12.2 Definition



for UMTS5.1 (V1.2)


KPI Name PS Inter-RAT Handover Success Ratio (GPRS to WCDMA)

Measurement Scope

RNC、Cell

Formula %100_ ×=nHOAttemptIPSInterRATnHOSuccessIPSInterRATSRHOPSInterRAT in

Associated Counters


Notes None

7.13 Class A - HSDPA Inter-RAT Handover Success Rate (WCDMA to GPRS)

7.13.1 Description

This KPI can be used to evaluate the HSDPA inter-RAT handover success ratio in one cell,

from WCDMA to GPRS.

7.13.2 Definition


KPI Name HSDPA Inter-RAT Handover Success Ratio (from WCDMA to

GPRS)

Measurement Scope

Cell

Formula %100_ ×=ptRATHOAttemHSDPAInterssRATHOSucceHSDPAInterSRRATHOHSDPAInter

Associated Counters

See ANNEX

Notes None


for UMTS5.1 (V1.2)


7.14 Class B - SRNC Relocation Preparation Success Ratio

7.14.1 Description


serves as SRNC.

7.14.2 Definition

Table34 SRNC Relocation Preparation Success Ratio

KPI Name SRNC Relocation Preparation Success Ratio

Measurement Scope

RNC

Formula %100PrRe

Re_ ×=ttempteparationAlocationSRNC

ccesslocationSuSRNCSRSRNCRP

Associated Counters

See ANNEX

Notes None

7.15 Class B - TRNC Relocation Preparation Success Ratio

7.15.1 Description


serves as TRNC.

7.15.2 Definition

Table35 TRNC Relocation Preparation Success Ratio

KPI Name TRNC Relocation Preparation Success Ratio

Measurement Scope

RNC

Formula %100PrRe

Re_ ×=ttempteparationAlocationTRNC

ccesslocationSuTRNCSRTRNCRP


for UMTS5.1 (V1.2)


Associated Counters

See ANNEX

Notes None

7.16 Class A – E-DCH Soft Handover Success Rate

7.16.1 Description

This KPI can be used to evaluate the soft handover success ratio of HSUPA service in a cell.

7.16.2 Definition

Table36 E-DCH Soft Handover Success Rate

KPI Name E-DCH Soft Handover Success Rate

Measurement Scope

Cell

Formula %100__ ×=empNumEDCHSHOAttcessNumEDCHSHOSucSRSHOEDCH

Associated Counters

See ANNEX

Notes None

7.17 Class A – E-DCH Service Cell Change Success Rate with SHO（HSUPA to

HSUPA）

7.17.1 Description

This KPI can be used to evaluate the E-DCH service cell change success rate with SHO


7.17.2 Definition

Table37 E-DCH Service Cell Change Success Rate with SHO


for UMTS5.1 (V1.2)


KPI Name E-DCH Service Cell Change Success Rate with SHO（HSUPA to

HSUPA）

Measurement Scope

Cell

Formula %100_______ ×=

tNumSCellChgAtSHOEDCHcNumSCellChgSuSHOEDCHSRSCellChgSHOEDCH

Associated Counters

See ANNEX

Notes None

7.18 Class A – E-DCH Service Cell Change Success Rate with Inter-HHO

（HSUPA to HSUPA）

7.18.1 Description

This KPI can be used to evaluate the E-DCH service cell change success rate with Inter-HHO


7.18.2 Definition

Table38 E-DCH Service Cell Change Success Rate with Inter-HHO

KPI Name E-DCH Service Cell Change Success Rate with Inter-HHO（HSUPA to HSUPA

Measurement Scope

Cell

Formula _______ ×=

tempNumSCellChgAtInterHHOEDCHccessNumSCellChgSuInterHHOEDCHSRSCellChgInterHHOEDCH

Associated Counters

See ANNEX

Notes None


for UMTS5.1 (V1.2)


7.19 Class A – E-DCH to DCH Handover Success Rate（Intra Cell）

7.19.1 Description


E-DCH to DCH in the same cell.

7.19.2 Definition

Table39 E-DCH to DCH Handover Success Rate（Intra Cell）

KPI Name E-DCH to DCH Handover Success Rate（Intra Cell）

Measurement Scope

Cell

Formula %100_______ ×=

mHOAttempNuIntraCellEtoDumHOSuccessNIntraCellEtoDSRHOIntraCellEtoD

Associated Counters

See ANNEX

Notes None

7.20 Class A – DCH to E-DCH Handover Success Rate（Intra Cell）

7.20.1 Description


DCH to E-DCH in the same cell.

7.20.2 Definition

Table40 DCH to E-DCH Handover Success Rate（Intra Cell）

KPI Name DCH to E-DCH Handover Success Rate（Intra Cell）

Measurement Scope

Cell


for UMTS5.1 (V1.2)


Formula %100_______ ×=

mHOAttempNuIntraCellDtoEumHOSuccessNIntraCellDtoESRHOIntraCellDtoE

Associated Counters

See ANNEX

Notes None

7.21 Class A – E-DCH to DCH Handover Success Rate（with Inter HHO）

7.21.1 Description

This KPI can be used to evaluate the channel switch from E-DCH to DCH with inter HHO

procedure.

7.21.2 Definition

Table41 E-DCH to DCH Handover Success Rate（with Inter HHO）

KPI Name E-DCH to DCH Handover Success Rate（with Inter HHO）

Measurement Scope

Cell

Formula %100_ ×=mHOAttempNuEtoDInterH

umHOSuccessNEtoDInterHSRHOEtoDInterH

Associated Counters

See ANNEX

Notes None

7.22 Class A – HSUPA Inter-RAT Handover Success Rate (UTRAN to GPRS)

7.22.1 Description

This KPI can be used to evaluate the HSUPA service Inter-RAT handover success rate from

UTRAN to GPRS.


for UMTS5.1 (V1.2)


7.22.2 Definition

Table42 HSUPA Inter-RAT Handover Success Rate (UTRAN to GPRS)

KPI Name HSUPA Inter-RAT Handover Success Rate (UTRAN to GPRS)

Measurement Scope

Cell

Formula %100_ ×=pNumRATHOAttemHSUPAInterssNumRATHOSucceHSUPAInterSRRATHOHSUPAInter

Associated Counters

See ANNEX

Notes None

8 Service Integrity KPIs

8.1 Class A - PS Service UL Average Throughput

8.1.1 Description

This grouped KPI can be used to evaluate the busy hour UL throughput of PS service in each

cell. According to the experience from commercial network, there are nine services listed in the

following definition.

8.1.2 Definition

Table43 PS Service UL Average Throughput

KPI Name PS Service UL Average Throughput

Measurement Scope

Cell

Formula

ThroughputKULAveragePSStr 64





for UMTS5.1 (V1.2)







Associated Counters

See ANNEX

Notes Unit：kbps

8.2 Class A - PS Service DL Average Throughput

8.2.1 Description

This grouped KPI can be used to evaluate the busy hour DL throughput of PS service in each

cell. According to the experience from commercial network, there are twelve services listed in

the following definition.

8.2.2 Definition

Table44 PS Service DL Average Throughput

KPI Name PS Service DL Average Throughput

Measurement Scope

Cell

Formula




ThroughputKDLAveragePSInter 64




ThroughputKDLAveragePSBkg 64



for UMTS5.1 (V1.2)




Associated Counters

See ANNEX

Notes Unit：kbps

8.3 Class B - Service UL Average BLER

8.3.1 Description

This grouped KPI can be used to evaluate the UL BLER value of service in each cell. According

to the experience from commercial network, there are three services listed in the following

definition.

8.3.2 Definition

Table45 Service UL BLER

KPI Name Service UL BLER

Measurement Scope

Cell

Formula

AMRULBLER

VPULBLER

KULBLERPS 64

Associated Counters

See ANNEX

Notes None

8.4 Class B - DL RLC Average Retransmission Ratio

8.4.1 Description

This KPI can be used to evaluate the DL RLC average retransmission in one Cell.


for UMTS5.1 (V1.2)


8.4.2 Definition

Table46 DL RLC Average Retransmission Ratio

KPI Name DL RLC Average Retransmission Ratio

Measurement Scope

Cell

Formula %100Re×=

lockAMDLRLCSentBdBlockAMtransmitteDLRLCDLRLCARR

Associated Counters

See ANNEXCell

Notes None

8.5 Class B - HSDPA RLC Throughput

8.5.1 Description

This KPI can be used to evaluate the DL RLC average throughput in one cell.

8.5.2 Definition

Table47 HSDPA RLC Troughput

KPI Name HSDPA RLC Troughput

Measurement Scope

Cell

Formula

Associated Counters

See ANNEX



for UMTS5.1 (V1.2)


8.6 Class B - HSUPA RLC Throughput

8.6.1 Description

This KPI can be used to evaluate the UL RLC average throughput in one cell.

8.6.2 Definition

Table48 HSUPA RLC Troughput

KPI Name HSUPA RLC Troughput

Measurement Scope

Cell

Formula

Associated Counters

See ANNEX


9 Availability KPIs

9.1 Class B - Worst Cell Ratio

9.1.1 Description

This KPI can be used to evaluate the effect of cells with poor call drop rate or call setup

success rate to the deteriorating of network performance in one RNC.

9.1.2 Definition

Table49 Worst Cell Ratio

KPI Name Worst Cell Ratio (WCR)

Measurement Scope

RNC


for UMTS5.1 (V1.2)


Formula %100%)321(%)9521( ,×

><=

sInRNCmberOfCellTheTotalNuandBBorandAAwhichfCellsTheNumberOWCR

A1:See AMR RAB Setup Success Ratio

A2:See VP RAB Setup Success Ratio

B1:See AMR Call Drop Ratio

Associated Counters

B2:See VP Call Drop Ratio

Notes

95% and 3% are refered by the experience from commercial

network while the traffic with AMR voice and video phone is

bigger than 0.1 Erlang.

9.2 Class B - IU Paging Congestion Ratio

9.2.1 Description

This KPI can be used to evaluate the consumption of PCCH bandwidth on busy hour within IU

interface.

9.2.2 Definition

Table50 IU Paging Congestion Ratio

KPI Name IU Paging Congestion Ratio

Measurement Scope

RNC、Cell

Formula %100×=temptIUPagingAt

ssIUPagingLoIUPagingCR

Associated Counters


Notes None


for UMTS5.1 (V1.2)


9.3 Class B - Admission Refused Ratio

9.3.1 Description

This KPI can be used to evaluate the admission refused ratio of radio network busy hour in a

cell.

9.3.2 Definition

Table51 Admission Refused Ratio

KPI Name Admission Refused Ratio

Measurement Scope

Cell

Formula %100ReRe

×=questNumsourceTotal

nNumNoAdmissionRatioNoAdmissio

Associated Counters

See ANNEX

Notes None

9.4 Class B - Congested Cell Ratio

9.4.1 Description

This KPI can be used to evaluate the utility ratio of radio network resources on busy hour in one

RNC.

9.4.2 Definition

Table52 Congested Cell Ratio

KPI Name Congested Cell Ratio

Measurement Scope

RNC

Formula %100×=sInRNCmberOfCellTheTotalNu

yHourCellsOnBusfCongestedTheNumberOICR

Associated See ANNEX


for UMTS5.1 (V1.2)


Counters

Notes

yHourCellsOnBusfCongestedTheNumberO is refered by summing up the

number of cells congested in DL or UL radio resources on busy

hour.

9.5 Class B - Unserviceable Cell Ratio

9.5.1 Description

This KPI can be used to evaluate how serious the unserviceable cells cause the degrading of

network performance on busy hour in one RNC.

9.5.2 Definition

Table53 Unserviceable Cell Ratio

KPI Name Unserviceable Cell Ratio

Measurement Scope

RNC

Formula %1000 ,×

>=

sInRNCmberOfCellTheTotalNulTimeCellUnavaiwhichfCellsTheNumberOUCR

Associated Counters

See ANNEX

Notes None

9.6 Class B - Average CPU Load

9.6.1 Description

This KPI can be used to evaluate the consumption of CPU on busy hour in RNC system.

9.6.2 Definition

Table54 Average CPU Load


for UMTS5.1 (V1.2)


KPI Name Average CPU Load

Measurement Scope

RNC

Formula lityMeanCPUUti

Associated Counters

See ANNEX

Notes lityMeanCPUUti is the CPU average load showed by percentage

9.7 Class B - IUB Bandwidth Utilizing Ratio

9.7.1 Description

This grouped KPI can be used to evaluate the ratio of consumption of IUB bandwidth and

configured IUB bandwidth in one NodeB for uplink and downlink on busy hour, for the

consumption of interactive and background service can’t keep the full rate all time on the

configured IUB bandwidth.

9.7.2 Definition

Table55 IUB Bandwidth Utilizing Ratio

KPI Name IUB Bandwidth Utilizing Ratio

Measurement Scope

NodeB

Formula

%100Re

×=uplink

uplinkuplink widthrationBandIUBConfigu


%100Re

×=downlink

downlinkdownlink widthrationBandIUBConfigu


Associated Counters

See ANNEX

Notes uplinkwidthrationBandIUBConfigu and downlinkwidthrationBandIUBConfigu

is based on the calculation of the transmission configuration of each


for UMTS5.1 (V1.2)


NodeB in a RNC.

10 Traffic KPIs

10.1 Class A - CS Equivalent Erlang

10.1.1 Description

This KPI can be used to evaluate the equivalent traffic of all CS service of one RNC.

10.1.2 Definition

Table56 CS Equivalent Traffic

KPI Name CS Equivalent Traffic

Measurement Scope

RNC

Formula ntErlCSEquivale

valentErlCSPeakEqui

Associated Counters

See ANNEX

Notes Unit: Erl

10.2 Class A - PS UL Throughput

10.2.1 Description

This KPI can be used to evaluate the UL throughput of all PS service of one RNC.

10.2.2 Definition

Table57 PS UL Throughput


for UMTS5.1 (V1.2)


KPI Name PS UL Throughput

Measurement Scope

RNC

Formula utUlThroughp

ughputUlPeakThro

Associated Counters

See ANNEX

Notes Unit: kbps

10.3 Class A - PS DL Throughput

10.3.1 Description

This KPI can be used to evaluate the DL throughput of all PS service of one RNC.

10.3.2 Definition

Table58 PS DL Throughput

KPI Name PS DL Throughput

Measurement Scope

RNC

Formula utDlThroughp

ughputDlPeakThro

Associated Counters

See ANNEX

Notes Unit: kbps

10.4 Class A - UL Traffic of Typical Radio Bearers

10.4.1 Description

This grouped KPI can be used to evaluate the average UL traffic of typical radio bearers on

busy hour in one RNC, which the meaning of the traffic from the different sevice is different


for UMTS5.1 (V1.2)


despite of in the same unit.

10.4.2 Definition

Table59 UL Traffic of Typical Radio Bearers

KPI Name UL Traffic of Typical Radio Bearers

Measurement Scope

RNC、Cell

Formula ErlKULAMR _2.12

ErlKULCSConv _64

Associated Counters


Notes Unit: Erl

10.5 Class A - DL Traffic of Typical Radio Bearers

10.5.1 Description

This grouped KPI can be used to evaluate the average DL traffic of typical radio bearers on

busy hour in one RNC, which the meaning of the traffic from the different sevice is different in

despite of the same unit.

10.5.2 Definition

Table60 DL Traffic of Typical Radio Bearers

KPI Name DL Traffic of Typical Radio Bearers

Measurement Scope

RNC、Cell

Formula ErlKDLAMR _2.12

ErlKDLCSConv _64

Associated Counters



for UMTS5.1 (V1.2)


Notes Unit: Erl

10.6 Class A - HSDPA Mean UE Number

10.6.1 Description

This grouped KPI can be used to evaluate the average DL traffic of HSDPA service on busy

hour in one Cell.

10.6.2 Definition

Table61 HSDPA mean ue number

KPI Name HSDPA mean ue number

Measurement Scope

Cell

Formula ENumberHSDPAMeanU

Associated Counters

See ANNEX

Notes should be statistic In busy hour

10.7 Class A - HSDPA RLC Traffic Volume

10.7.1 Description

This grouped KPI can be used to evaluate the total traffic volume of HSDPA service in certain

time in one Cell.

10.7.2 Definition

Table62 HSDPA RLC Traffic Volume

KPI Name HSDPA RLC Traffic Volume

Measurement Cell


for UMTS5.1 (V1.2)


Scope

Formula icVolumHSDPATraff

Associated Counters

See ANNEX

Notes Unit: byte

10.8 Class A - HSUPA Mean UE Number

10.8.1 Description

This KPI can be used to evaluate the average UL traffic of HSUPA service in one Cell.

10.8.2 Definition

Table63 HSUPA mean UE number

KPI Name HSUPA mean UE number

Measurement Scope

Cell

Formula ENumberHSUPAMeanU

Associated Counters

See ANNEX

Notes Unit: Erl

10.9 Class A - HSUPA RLC Traffic Volume

10.9.1 Description

This grouped KPI can be used to evaluate the total traffic volume of HSUPA service in certain

time in one Cell.


for UMTS5.1 (V1.2)


10.9.2 Definition

Table64 HSUPA RLC Traffic Volume

KPI Name HSUPA RLC Traffic Volume

Measurement Scope

Cell

Formula

Associated Counters

See ANNEX

Notes Unit: byte

10.10 Class B - UL Traffic Volume of QoS Classes

10.10.1 Description

This grouped KPI can be used to evaluate the cell’s UL traffic volume of QoS classes in one

cell.

10.10.2 Definition

Table65 UL Traffic Volume of QoS Classes

KPI Name UL Traffic Volume of QoS Classes

Measurement Scope

Cell

Formula

umeTrafficVolCellULConv

merafficVoluCellULStrT


merafficVoluCellULBkgT

Associated Counters

See ANNEX

Notes Unit: bit


for UMTS5.1 (V1.2)


10.11 Class B - DL Traffic Volume of QoS Classes

10.11.1 Description

This grouped KPI can be used to evaluate the cell’s DL traffic volume of QoS classes in one

cell.

10.11.2 Definition

Table66 DL Traffic Volume of QoS Classes

KPI Name DL Traffic Volume of QoS Classes

Measurement Scope

Cell

Formula

umeTrafficVolCellDLConv

merafficVoluCellDLStrT

lumerTrafficVoCellDLInte

merafficVoluCellDLBkgT

Associated Counters

See ANNEX

Notes Unit: bit

11 ANNEX

1. Associated Counters

2. Reference Name 3. Associated Counters 4. Specification

5. MeanRTWP go back VS.MeanRTWP

Mean RTWP of a cell, that is, mean

number of the sum of the RTWP


Unit: dBm

6. MeanTCP VS.MeanTCP

Mean TCP of a cell, that is, mean

number of the sum of the TCP


Unit: dBm

7. lTimeCellUnavai go back VS.Cell.UnavailTime.OM Unavailability Duration of a cell


for UMTS5.1 (V1.2)


8. temptIUPagingAt go back VS.RANAP.Paging.Att.Idle

UE Number of Times of Paging Idle UE

9. ccessIUPagingSu VS.RANAP.Paging.Succ.Id

leUE

Successful Number of Times of

Paging Idle UE

VS.RAB.AttEstabCS.Conv



in a cell 10. AttemptCSRABSetup (Cell) go

back VS.RAB.AttEstabCS.Str



cell

VS.RAB.SuccEstabCS.Co

nv


successfully for conversational

services in a cell 11. SuccessCSRABSetup (Cell)

VS.RAB.SuccEstabCS.Str


successfully for streaming services

in a cell

VS.RAB.AttEstabPS.Conv



in a RNC

VS.RAB.AttEstabPS.Str



cell

VS.RAB.AttEstabPS.Inter


establish for interactive services in a

cell

12. AttemptPSRABSetup (cell) go

back

VS.RAB.AttEstabPS.Bkg


establish for background services in

a cell

VS.RAB.SuccEstabPS.Co

nv



VS.RAB.SuccEstabPS.Str Numbers of PS RABs Established


VS.RAB.SuccEstabPS.Inte

r



13. SuccessPSRABSetup (cell)

VS.RAB.SuccEstabPS.Bkg Numbers of PS RABs Established


RRC.AttConnEstab.OrgCo

nvCall


cell

RRC.AttConnEstab.OrgStr

Call Originating Streaming Call in a cell

14. serviceionAttemptRRCConnect (C

ell) go back

RRC.AttConnEstab.OrgInt

erCall Originating Interactive Call in a cell


for UMTS5.1 (V1.2)


RRC.AttConnEstab.OrgBk

gCall Originating Background Call in a cell

RRC.AttConnEstab.OgSub

Call


cell

RRC.AttConnEstab.TmCo

nvCall


cell

RRC.AttConnEstab.TmStr

Call Terminating Streaming Call in a cell

RRC.AttConnEstab.TmInte

rCall Terminating Interactive Call in a cell

RRC.AttConnEstab.TmBkg

Call Terminating Background Call in a cell

RRC.AttConnEstab.EmgC

all Emergency Call in a cell

RRC.AttConnEstab.Unkno

wn Unknow in a cell

RRC.AttConnEstab.OgHh

PrSig


a cell

RRC.AttConnEstab.OgLw

PrSig


cell

RRC.AttConnEstab.CallRe

Est


a cell

RRC.AttConnEstab.TmHh

PrSig


a cell

RRC.AttConnEstab.TmLw

PrSig Call re-Establishment

RRC.SuccConnEstab.OgC

onvCall


cell


StrCall Originating Streaming Call in a cell

RRC.SuccConnEstab.OrgIt

rCall Originating Interactive Call in a cell


BkgCall Originating Background Call in a cell


SubCall


cell

RRC.SuccConnEstab.TmC

onvCall


cell

RRC.SuccConnEstab.TmS

trCall Terminating Streaming Call in a cell

15. serviceionSuccessRRCConnect (C

ell)

RRC.SuccConnEstab.TmIt Terminating Interactive Call in a cell


for UMTS5.1 (V1.2)


rCall

RRC.SuccConnEstab.TmB

kgCall Terminating Background Call in a cell

RRC.SuccConnEstab.Emg

Call Emergency Call in a cell

RRC.SuccConnEstab.Unk

own Unknow in a cell

RRC.SuccConnEstab.OgH

hPrSig


a cell

RRC.SuccConnEstab.OgL

wPrSig


cell

RRC.SuccConnEstab.Call

ReEst


a cell

RRC.SuccConnEstab.TmH

hPrSig


a cell

RRC.SuccConnEstab.TmL

wPrSig Call re-establishment in a cell


elRes InterRAT cell Reselection in a cell


CO


WCDMA in a cell

RRC.AttConnEstab.Reg Register in a cell

16. otherionAttemptRRCConnect (Ce

ll) go back

RRC.AttConnEstab.Detach Detach in a cell


TCelRes InterRAT cell Reselection in a cell


TCCO


WCDMA in a cell

RRC.SuccConnEstab.Reg Register in a cell

17. otherionSuccessRRCConnect (Ce

ll)

RRC.SuccConnEstab.Deta

ch Detach in a cell

18. pAttemptAMRRABSetu (cell) go

back VS.RAB.AttEstab.AMR

Number of AMR Service RABs


19. pSuccessAMRRABSetu (cell) VS.RAB.SuccEstab.AMR Number of AMR Service RABs


20. AttemptVPRABSetup (cell) go

back VS.RAB.AttEstCS.Conv.64



21. SuccessVPRABSetup (cell) VS.RAB.SucEstabCS.Con

v.64



22. ccessRABSetupSuHSDPA _

go back

VS.HSDPA.RAB.SuccEsta

b




for UMTS5.1 (V1.2)


by HSDPA

23. temptRABSetupAtHSDPA _ VS.HSDPA.RAB.AttEstab



HSDPA

24. ccessRABSetupSuHSUPA _

go back

VS.HSUPA.RAB.SuccEsta

b



by HSUPA

25. temptRABSetupAtHSUPA _ VS.HSUPA.RAB.AttEstab



HSUPA

VS.RAB.Loss.CS.Abnorm :

Numbers of abnormally released

RABs except RF causes in a cell 26. leasemalCSRABAbnor Re (cell)

go back


+ VS.RAB.Loss.CS.RF VS.RAB.Loss.CS.RF : Number of

Released RABs Triggered by RNC

due to RF Reason

27. leaseCSRAB Re (cell)

VS.RAB.Loss.CS.RF +


+ VS.RAB.Loss.CS.Norm

VS.RAB.Loss.CS.Norm : Numbers


RNC due to CS Normal Cause in a

cell

28. leasermalAMRRABAbno Re (c

ell) go back VS.RAB.Loss.CS.AMR

Number of released CS AMR service


29. leaseAMRRABRe

VS.RAB.Loss.CS.AMR +

VS.RAB.Loss.CS.Norm.A

MR

VS.RAB.Loss.CS.Norm.AMR :

Numbers of Released RABs

Triggered by RNC due to CS Normal

Cause in a cell(AMR)

30. leasemalVPRABAbnor Re (cell)

go back VS.RAB.Loss.CS.Conv64K

Number of released CS 64 k service


31. leaseVPRAB Re (cell)

VS.Norm.Rel.CS.Conv.RB.

64 +

VS.RAB.Loss.CS.Conv64

K

Numbers of VP Service RABs

released

32. leasemalPSRABAbnor Re (cell)

go back

VS.RAB.Loss.PS.RF +


VS.RAB.Loss.PS.RF :

Numbers of Abnormally Released

RABs except RF causes in a cell


for UMTS5.1 (V1.2)


VS.RAB.Loss.PS.Abnorm : Number

of Released RABs triggered by RNC

due to RF reason

33. leasePSRAB Re (cell)

VS.RAB.Loss.PS.RF +


+ VS.RAB.Loss.PS.Norm

VS.RAB.Loss.PS.Norm : Numbers


RNC due to PS Normal Cause in a

cell

VS.HSDPA.RAB.Loss.Abnorm.NonR

F : Number of released PS

service RABs carried by HSDPA

triggered by RNC in a cell, the cause

is not RF. 34. leaselRABAbnormaHSDPA Re_ go back

VS.HSDPA.RAB.Loss.Abn

orm.NonRF +

VS.HSDPA.RAB.Loss.RF

VS.HSDPA.RAB.Loss.RF :


RABs carried by HSDPA triggered

by RNC in a cell, the cause is RF.

VS.HSDPA.RAB.Loss.Norm :




35. leaseRABNormalHSDPA Re_

VS.HSDPA.RAB.Loss.Nor

m +

VS.HSDPA.RAB.Loss.InAc

tivity

VS.HSDPA.RAB.Loss.InActivity :



triggered ,the cause is User

Inactivity.

36. leaselRABAbnormaHSUPA Re_go back

VS.HSUPA.RAB.Loss.Abn

orm

VS.HSUPA.RAB.Loss.Abnorm:

Number of abnormal released PS

service RABs carried by HSUPA

triggered by RNC in a cell,

37. leaseRABNormalHSUPA Re_

VS.HSUPA.RAB.Loss.Nor

m

VS.HSUPA.RAB.Loss.Norm :


RABs carried by HSUPA


38. mptSHOASUAtte go back VS.SHO.Att.RNC The number of attempts of soft

handovers in a RNC

39. essSHOASUSucc VS.SHO.Succ The number of successful soft

handovers in a RNC

40. mptSHOASUAtte (cell) go back SHO.AttRLAddUESide The number of attempts of soft


for UMTS5.1 (V1.2)


handover added cell in a cell

SHO.AttRLDelUESide The number of attempts of soft


SHO.SuccRLAddUESide The number of successful soft

handovers added cell in a cell 41. essSHOASUSucc (cell)

SHO.SuccRLDelUESide The number of successful soft


42. emptSoHOASUAtt go back VS.SoHO.ASU.AttRNC The number of attempts of softer

handovers in a RNC

43. cessSoHOASUSuc VS.SoHo.Succ The number of successful softer

handovers in a RNC

VS.SoHO.ASU.AttRLAdd The number of attempts of softer

handover added cell in a cell 44. emptSoHOASUAtt (cell) go back

VS.SoHO.ASU.AttRlDel The number of attempts of softer


VS.SoHO.ASU.SuccRLAdd

The number of successful softer

handovers added cell in a cell 45. cessSoHOASUSuc (cell)

VS.SoHO.ASU.SuccRlDel The number of successful softer


46. empNumHtoHSHOAtt go back VS.HSDPA.CellChg.AttOut

IntraRNC

Num of Service cell change attempts

from HSDPA cell to HSDPA cell

47. cessNumHtoHSHOSuc VS.HSDPA.CellChg.Succ

OutIntraRNC

Num of Service cell change

successful times from HSDPA cell to

HSDPA cell

48. mpNumHtoRHOAtte go back VS.HSDPA.ChR.HSDSCHt

oDCH.Att


from HSDSCH to DCH

49. essNumHtoRHOSucc VS.HSDPA.ChR.HSDSCHt

oDCH


handovers from HSDSCH to DCH

50. mpNumRtoHHOAtte go back VS.HSDPA.ChR.DCHtoHS

DSCH.Att


from DCH to HSDSCH

51. essNumRtoHHOSucc VS.HSDPA.ChR.DCHtoHS

DSCH


handovers from DCH to HSDSCH

52. cessNumEDCHSHOSuc go

back

VS.HSUPA.EDCH.SHO.Su

cc

Num of successful soft handover for



53. empNumEDCHSHOAtt VS.HSUPA.EDCH.SHO.Att

Num of soft handover requests for



54. cNumSCellChgSuSHOEDCH __ go back


Chg.Succ

Num of successful E-DCH service cell

change with SHO state


for UMTS5.1 (V1.2)


55. tNumSCellChgAtSHOEDCH __


Chg.Att

Num of E-DCH service cell change

attempt with SHO state

56. SCellChgSuInterHHOEDCH __ go back


.NoChR.Succ

Times of Success of Edch ServCell


Source ServCell)

57. SCellChgAtInterHHOEDCH __


.NoChR.Att

Times of Attempt of Edch ServCell


Source ServCell)

58. HOSuccessNIntraCellEtoD __ go back


EDCHtoDCH.Succ



DCH In a Cell

59. HOAttempNuIntraCellEtoD __


EDCHtoDCH.Att



DCH In a Cell

60. HOSuccessNIntraCellDtoE __ go back


DCHtoEDCH.Succ



EDCH In a Cell.

61. HOAttempNuIntraCellDtoE __


DCHtoEDCH.Att



EDCH In a Cell

62. umHOSuccessNEtoDInterH

go back

VS.HSUPA.ChR.InterFreq.

EDCHtoDCH.Succ

The number of Successful Channel

type Switch from Edch to DCH of

Interfreq HHO.

63. mHOAttempNuEtoDInterH VS.HSUPA.ChR.InterFreq.

EDCHtoDCH.Att

The number of Attempt Channel type

Switch from Edch to DCH of

Interfreq HHO.

64. ssNumRATHOSucceHSUPAInter go back

VS.HSUPA.IRATHO.Succ

OutPSUTRAN

the number of HSUPA User succeed

to SysHo out system.

65. pNumRATHOAttemHSUPAInter

VS.HSUPA.IRATHO.AttOu

tPSUTRAN

the number of Hsupa user attempt to

SysHo out system.

66. HHOAttempt go back VS.HHO.Att.RNC Number of Hard Handover Requests

67. HHOSuccess VS.HHO.Succ.RNC Number of Successful Hard

Handovers

68. mHOAttempNuHtoHIntraH go

back


aRNCIntraFreq

Number of Intra Frequency Hard


69. umHOSuccessNHtoHIntraH VS.HSDPA.HHO.succOutI

ntraRNCIntraFreq

Number of Successful Intra


HSDPA

70. temptInterHHOAt go back VS.HHO.InterFreq.Att.RNC Number of Inter-Frequency Hard

Handover Requests


for UMTS5.1 (V1.2)


71. ccessInterHHOSu VS.HHO.InterFreq.Succ.R

NC

Number of Successful

Inter-Frequency Hard Handovers

72. mHOAttempNuHtoHInterH go

back


aRNCInterFreq

Number of Inter Frequency Hard


73. umHOSuccessNHtoHInterH VS.HSDPA.HHO.SuccOutI

ntraRNCInterFreq

Number of Successful Inter


HSDPA

74. HOAttemptCSInterRAT go

back

VS.IRATHO.AttCSOut.RN

C



75. HOSuccessCSInterRAT VS.IRATHO.SuccCSOut.R

NC



76. HOAttemptCSInterRAT (cell) go

back IRATHO.AttOutCS



77. HOSuccessCSInterRAT (cell) IRATHO.SuccOutCS Number of CS Domain Inter-RAT


78. utHOAttemptOPSInterRAT go

back

VS.IRATHO.AttPSOutUTR

AN.RNC



from RNC

79. utHOSuccessOPSInterRAT VS.IRATHO.SuccPSOutU

TRAN.RNC



Initiated by RNC

80. nHOAttemptIPSInterRAT go

back

VS.IRATHO.AttPSInUE.R

NC



81. nHOSuccessIPSInterRAT VS.IRATHO.SuccPSInUE.

RNC



Initiated by UE

82. utHOAttemptOPSInterRAT (cel

l) go back IRATHO.AttOutPSUTRAN



from RNC

83. utHOSuccessOPSInterRAT (cel

l)

IRATHO.SuccOutPSUTRA

N



Initiated by RNC


CO 84. nHOAttemptIPSInterRAT (cell)

go back RRC.AttConnEstab.IRATC

elRes



85. nHOSuccessIPSInterRAT (cell) IRATHO.SuccOutPSUE



Initiated by UE

86. ssRATHOSucceHSDPAInter VS.IRATHO.HSDPA.Succ

OutPSUTRAN

Number of Successful HSDPA



for UMTS5.1 (V1.2)


go back to GPRS

87. ptRATHOAttemHSDPAInter VS.IRATHO.HSDPA.AttOu

tPSUTRAN

Attempts number of HSDPA


to GPRS

88. ttempteparationAlocationSRNC PrRe

go back RELOC.AttPrep

Number of Preparations for SRNC

Relocations

RELOC.SuccCS Number of Successful SRNC

Relocation Commits 89. ccesslocationSuSRNC Re

RELOC.SuccPS Number of Successful SRNC

Relocation Commits

VS.TRELOC.AttPrep.UEIn

v



Types 90. ttempteparationAlocationTRNC PrRe

go back VS.TRELOC.AttPrep.UEN

onInv



Types


Inv


Relocations of Different Types 91. ccesslocationSuTRNC Re


NotInv


Relocations of Different Types

92. RLhberOfUEWitN 1um go back VS.SHO.AS.1 Average Number of UEs with One RL

VS.SHO.AS.2Softer Average Number of UEs with Two

RLs Combined 93. RLhberOfUEWitN 2um

VS.SHO.AS.2Soft Average Number of UEs with Two

RLs Uncombined

VS.SHO.AS.3Soft2Softer Average Number of UEs with Three

RLs and Two Combined

VS.SHO.AS.3Soft Average Number of UEs with Three

RLs Uncombined 94. RLhberOfUEWitN 3um

VS.SHO.AS.3Softer Average Number of UEs with Three

RLs Combined

VS.RAC.CodeRejDL Num of Admission refuse because of

no code resource

VS.RAC.NoAdmUL Num of Admission refuse because of

no UL power resource

VS.RAC.NoAdmDL Num of Admission refuse because of

no DL power resource

VS.RRNBCred.EmerCall.R

ej


no CE resource during emergency

call request

95. nNumNoAdmissio go back

VS.RRNBCred.NonEmerC Num of Admission refuse because of


for UMTS5.1 (V1.2)


all.Rej no CE resource during


VS.RRIUB.NonEmerCall.R

ej


no IuB resource during


VS.RRIUB.EmerCall.Rej


no IuB resource during emergency

call request

96. questNumsourceTotal ReRe VS.CellResApply.DCH Total num of RNC apply for dedicated

resource for UE

97. lityMeanCPUUti go back VS.MeanCPUUtil.SPU CPU Utilization of WSPU

98. uplinkficrationTrafIUBConfigu VS.QAAL2.AllocedAveBwd

.AAL2BitRate


AAL2 bit rate in backward direction

99. downlinkficrationTrafIUBConfigu

VS.QAAL2.AllocedAveFwd

.AAL2BitRate


AAL2 bit rate in forward direction

（VS.UNILNK.RXCELLS）

×53×8

Bits Received by UNI Link during a

statistical period 100. uplinkficalTimeTrafIUB Re

（VS.IMAGRP.RXCELLS）

×53×8

Bits Received by IMA Group during a

statistical period

（VS.UNILNK.TXCELLS）

×53×8

Bits Sent by UNI Link during a

statistical period 101. downlinkficalTimeTrafIUB Re

（VS.IMAGRP.TXCELLS）

×53×8

Bits Sent by IMA Group during a

statistical period

VS.CN.Page.Loss.IUFC

Number of Paging Messages

Discarded due to Iu Interface Flow

Control 102. ssIUPagingLo go back

VS.CN.Page.Loss.PCHCo

ng

Number of Paging Messages Lost

due to PCH Congestion

103. ssIUPagingLo (cell) go back VS.RRC.Paging1.Loss.PC

HCong.Cell Discard paging due to congestion

104. temptIUPagingAt (cell) VS.RRC.Paging1.Att.Cell The number of paging sended by a

cell

105. AMRULBLER go back VS.ULBlerAMR UL BLER of AMR Speech Service on

DCH

106. VPULBLER VS.ULBlerCSRT.64 UL BLER of CS 64 K Real-time

Service on DCH

107. KULBLERPS64 VS.ULBlerPSRT.64 UL BLER of PS 64 K Real-time

Service on DCH

108. ThroughputKULAveragePSStr 64 VS.PS.Str.Kbps.UL64 UL Bit Rate of PS 64K Streaming

Traffic


for UMTS5.1 (V1.2)


go back



Traffic



Traffic



Traffic



Traffic



Traffic



Traffic



Traffic



Traffic

117. ThroughputKDLAveragePSStr64 go back


Traffic



Traffic



Traffic

120. ThroughputKDLAveragePSInter 64


Traffic



Traffic



Traffic



Traffic

124. ThroughputKDLAveragePSBkg 64


Traffic



Traffic

126. ThroughputKDLAveragePSBkg144 VS.PS.BKG.Kbps.DL144 DL Bit Rate of PS 144K Background

Traffic


for UMTS5.1 (V1.2)




Traffic

VS.RLC.AM.Tx.Trf.PDU Total Sended traffic PDU of RLC in

AM model 128. lockAMDLRLCSentB (cell) go

back VS.AM.RLC.Tx.Sig.PDU

Total Sended signaling PDU of RLC

in AM model

VS.RLC.AM.Rtx.Trf.PDU Total Resended traffic PDU of RLC in

AM model 129. dBlockAMtransmitteDLRLC Re

VS.AM.RLC.Rtx.Sig.PDU Total Resended signaling PDU of

RLC in AM model

130. ntErlCSEquivale go back VS.CSLoad.Erlang.Equiv.

RNC

Equivalent Erlang of CS Service of

one RNC in statistical period

131. valentErlCSPeakEqui VS.CSLoad.MaxErlang.Eq

uiv.RNC

Max Equivalent Erlang values of all

services in the CS domain of the

RNC

132. utUlThroughp go back VS.PSLoad.ULThruput.RN

C

UL Throughput of PS Service of one


133. ughputUlPeakThro VS.PSLoad.MaxULThruput

.RNC

Max uplink traffic of all services in the

PS domain of the RNC.

134. utDlThroughp go back VS.PSLoad.DLThruput.RN

C

DL Throughput of PS Service of one


135. ughputDlPeakThro VS.PSLoad.MaxDLThruput

.RNC

Max downlink traffic of all services in

the PS domain of the RNC

136. ErlKULAMR _2.12 go back VS.AMR.RB.UL.12.2 Mean Number of AMR Speech UEs

at 12.2k Bit Rates

137. ErlKULCSConv _64 VS.RB.ULConvCS.64.RNC



Rates

138. ErlKULAMR _2.12 (cell) go back VS.AMR.Ctrl.UL12.2 Mean Number of AMR Speech UEs

at 12.2k Bit Rates

139. ErlKULCSConv _64 (cell) VS.RB.DLConvCS.64



Rates

140. ErlKDLAMR _2.12 go back go

back VS.AMR.RB.DL.12.2

Mean Number of AMR Speech UEs

at 12.2k Bit Rates

141. ErlKDLCSConv _64 go back VS.RB.DLConvCS.64.RNC


Conversational service at DL 64k Bit

Rates

142. ErlKDLAMR _2.12 (cell) go back

go back VS.AMR.Ctrl.DL12.2 Mean number of AMR call in a cell


for UMTS5.1 (V1.2)


143. ErlKULCSConv _64 (cell) go back VS.RB.DLConvCS.64 Mean number of VP call in a cell

144. roughputHSDPARLCTh go

back

VS.HSDPA.MeanChThrou

ghput.TotalBytes


PS service carrie by HSDPA

145. ENumberHSDPAMeanU go back VS.HSDPA.UE.Mean.Cell Mean UE numer of HSDPA Service in

one cell

146. icVolumHSDPATraff go back VS.HSDPA.MeanChThrou

ghput.TotalBytes

Total Traffic Volume of HSDPA

Service of one cell in a cetain time

147. ENumberHSUPAMeanU go back VS.HSUPA.UE.Mean.Cell

Mean UE numer of HSUPA Service in

one cell

(VS.AMR.Ctrl.DL12.2) ×

12.2K

UL throughput of AMR Speech UEs

at 12.2KBit In a Cell 148. umeTrafficVolCellULConv go


t

UL throughput of CS 64K Streaming

Service In a Cell（＝DL）

149. merafficVoluCellULStrT VS.PS.Str.UL.64.Thruput UL throughput of PS 64K Streaming

Service In a Cell


Service In a Cell


Service In a Cell


Service In a Cell



Service In a Cell

VS.PS.bkg.UL.64.Thruput UL throughput of PS 64K Background

Service In a Cell





150. merafficVoluCellULBkgT

VS.PS.bkg.UL.384.Thruput ULthroughput of PS 384K


(VS.AMR.Ctrl.UL12.2)×

12.2K

DL throughput of AMR Speech UEs

at 12.2KBit 151. umeTrafficVolCellDLConv go


t

DL throughput of CS 64K

Conversational Service In a Cell


Service In a Cell


Service In a Cell 152. merafficVoluCellDLStrT


Service In a Cell


for UMTS5.1 (V1.2)



Service In a Cell


Service In a Cell


Service In a Cell

153. lumerTrafficVoCellDLInte


Service In a Cell

VS.PS.bkg.DL.64.Thruput DL throughput of PS 64K Background

Service In a Cell





154. merafficVoluCellDLBkgT



155. yHourCellsOnBusfCongestedTheNumberO

go back

VS.LCC.OverCongNumUL

>0 or

VS.LCC.OverCongNumD

L>0

Numbers of UL and DL overload

congestions respectively in a cell.

VS.UNI.Lnk.MeanKbps.Rx

Mean receive rate of a UNI link in a


kbps.

VS.IMA.Grp.MeanKbps.Rx

Mean receive rate of an IMA group in


kbps.

156. uplinkficalTimeTrafIUB Re go

back


Kbps.Rx

Mean receive rate of a FRA ATM link

in a given measurement period. Unit:

kbps.

VS.UNI.Lnk.MeanKbps.Tx

Mean send rate of a UNI link in a


kbps.

VS.IMA.Grp.MeanKbps.Tx

Mean send rate of an IMA group in a


kbps.

157. downlinkficalTimeTrafIUB Re


Kbps.Tx

Mean send rate of a FRA ATM link in


kbps.

158. leaseNormalAMRIuR Re__

goback

VS.Norm.Rel.CS.AMR.IurL

ink






for UMTS5.1 (V1.2)




159. leaseAbnormalAMRIuR Re__

VS.Abnorm.Rel.CS.AMR.I

urLink




160. leaseNormalVPIuR Re__ VS.Norm.Rel.CS.Conv.RB.

64.IurLink







161. leaseAbnormalVPIuR Re__ VS.Abnorm.Rel.CS.Conv.

RB.64.IurLink




162. leaseNormalPSRIuR Re_99_

VS.Norm.Rel.PS.BE.RB.0.

32.IurLink +


2.64.IurLink +


4.144.IurLink +


44.384.IurLink +

VS.Norm.Rel.PS.CCH.Iur

Link +









+


UeGen.IurLink



VS.Norm.Rel.PS.BE.RB.64.144.IurLin

k

VS.Norm.Rel.PS.BE.RB.144.384.IurLi

nk

VS.Norm.Rel.PS.CCH.IurLink


triggered by RNC due to normal

cause in the best cell which belongs

to the DRNC, the release causes

can be the following: Successful

Relocation User Inactivity Normal

Release.

VS.Abnorm.Rel.PS.BE.RB.0.32.UeG

en.IurLink

VS.Abnorm.Rel.PS.BE.RB.32.64.Ue

Gen.IurLink

VS.Abnorm.Rel.PS.BE.RB.64.144.U

eGen.IurLink

VS.Abnorm.Rel.PS.BE.RB.144.384.

UeGen.IurLink

VS.Abnorm.Rel.PS.CCH.UeGen.Iur

Link


triggered by

"release-due-to-UE-generated-signal

ing-connection-release" in the best


for UMTS5.1 (V1.2)


cell which belongs to the DRNC. For

the PS domain, the cause can

belong to normal release.

163. leaseAbnormalPSRIuR Re_99_

VS.Abnorm.Rel.PS.BE.RB.

0.32.IurLink +


B.32.64.IurLink +


B.64.144.IurLink +


B.144.384.IurLink +

VS.Abnorm.Rel.PS.CCH.I

urLink -









-


UeGen.IurLink

VS.Abnorm.Rel.PS.BE.RB.0.32.IurLin

k

VS.Abnorm.Rel.PS.BE.RB.32.64.IurLi

nk

VS.Abnorm.Rel.PS.BE.RB.64.144.Iur

Link

VS.Abnorm.Rel.PS.BE.RB.144.384.Iu

rLink

VS.Abnorm.Rel.PS.CCH.IurLink

: Numbers of released RABs Due to


which belongs to the DRNC


ghput.TotalBytes




ghput.TotalBytes



WCDMA Performance - Radio Access Network KPI Definition Manual for UMTS6_0_V1_1

Documents