This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Wall Panel & CladdingInstallation Hardware
Monarch Metal 1700 Ocean Ave Ronkonkoma, New York 11779 (631) 750 3000 [email protected]
Choosing the Correct Monarch Hanging System ................... 07
Standard Monarch Z Clips ...................08
Stainless Steel Monarch Z Clips ......... 14
Specialty Z Clips ...................................... 16
Ceiling System ......................................... 22
SYSTEMS
5(631)750-3000 www.monarchmetal.com
Monarch Metal has provided the fastest and easiest method to mount wall panels, signs, art work and more for close to 25 years.
The key advantages of the Monarch Z Clip system are:
• Simplicity of installation
• Strength and security of the mounting
• No visible screws or nails on the surface of the mounted panel
MO
NA
RC
H Z
CL
IPS
Overview
6 (631)750-3000 www.monarchmetal.com
For a typical 8’ high x 4’ wide panel, customers mount the continuous lengths along the wall at 3 different heights parallel with the floor. These are secured to studs at 16” on center or to blocking at 8”on center. The shorter panel clips are secured to the back of the panel every 12-15” horizontally.
To match fastener locations on the panel with those on the wall a single template can be used or one can use a story pole. Installation of the panel is accomplished by simply dropping the panel onto the continuous lengths mounted along the wall.
For a video of an installation, please visit our web-site at MonarchMetal.com
Monarch recommends a #8 Pan Head thread screw for attaching the shorter panel clips to the back side of MDF or particle board panels, and stocks these in 1/2”, 5/8” and 3/4” lengths.
The important constraint to remember for using the Monarch Z Clip system is that the height of the head of the screw must be less than .125” for our standard Monarch Z Clips.
MO
NA
RC
H Z
CL
IPS
Overview
.125”
DIM4plus
DIM4any
2 E
QU
AL
DIM
4”1 7/8”
4”dim
7(631)750-3000 www.monarchmetal.com
MO
NA
RC
H Z
CL
IPS
Choosing the Correct Monarch Hanging System
8 (631)750-3000 www.monarchmetal.com
MO
NA
RC
H Z
CL
IPS
MF375 ClipFeatures
Monarch Z Clip system for hanging interior panels where the installer desires a 3/8” length of engagement
1/2” clearance required between the top of the panel and the ceiling
6063-T6 Aluminum
MF375 Clip1
1/4” Projection
3/8’’ Lift off 2” Length
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
2 Inch
72 Inch, 144 Inch
Any
3/8 Inch
1/4 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MF375
1
MONARCH
Standard Z Clips
Standard Applications
3/8” Lift Off
1/4” Projection
FEATURES
9(631)750-3000 www.monarchmetal.com
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
2 Inch
72 Inch, 144 Inch
Any
3/8 Inch
1/4 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MF375
MO
NA
RC
H Z
CL
IPS
MF375 Even ClipFeatures
In line holes for 50% increase in panel processing speed
32mm hole spacing for line boring equipment
6063-T6 Aluminum
1/4” Projection
3/8’’ Lift off 2” Length
MONARCHSpecialty Clip with In-Line
Holes
Standard Z Clips
Alternative Clip for MF375
3/8’’ Lift Off
1/4’’ Projection
FEATURES
10 (631)750-3000 www.monarchmetal.com
MO
NA
RC
H Z
CL
IPS
Standard Z Clips
MF625 ClipFeatures
Monarch Z Clip system for hanging interior panels where the installer desires a 5/8” length of engagement
3/4” clearance required between the top of the panel and the ceiling
6063-T6 Aluminum
Standard Applications
5/8” Lift Off
3/16” Projection
FEATURES
MF625 Clip1
.200” Projection
5/8 Lift off 1 1/2” Length
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
1 1/2 Inch
72 Inch, 144 Inch
Any
5/8 Inch
3/16 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MF625
1
MONARCH
11(631)750-3000 www.monarchmetal.com
MO
NA
RC
H Z
CL
IPS
MF250 ClipFeatures
Monarch Z Clip system for hanging interior panels where the installer desires a 1/4” length of engagement
3/8” clearance required between the top of the panel and the ceiling
6063-T6 Aluminum
MF250 Clip1
1/4” Projection
1/4 Lift off 2” Length
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
2 Inch
72 Inch, 144 Inch
Any
1/4 Inch
1/4 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MF250
1
MONARCH
Standard Z Clips
Applications With Limited Clearance Above Panel
5/8” Lift Off
1/4” Projection
FEATURES
12 (631)750-3000 www.monarchmetal.com
MO
NA
RC
H Z
CL
IPS
MFSTR-050 ClipFeatures
High strength aluminum system compatible with up to a 3/8’’ hex bolt
1/2” clearance required between the top of the panel and the ceiling
6063-T6 Aluminum
Easily used for mounting on concrete block or other difficult materials
Ø.250 THRU x2
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
2 Inch
72 Inch, 144 Inch
Any
7/16 Inch
1/2 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MFSTR050
MFSTR-050 2” Clip
MFSTR-050 Continuous Length
1 2
1
2
2.000
(Available in lengths up to 144”)
.437
1.500
.500.125
Standard Z Clips
High Strength Applications
7/16” Lift Off
1/2” Projection
FEATURES
13(631)750-3000 www.monarchmetal.com
MO
NA
RC
H Z
CL
IPS
MFSTR-1125 ClipFeatures
Heavy duty adjustable height system for mounting curtain wall in exterior applications
Easy adjust bolt on clips for minor height adjustments
Easy fit engagement for locating
3/4” clearance required above the panel
6063-T6 Aluminum
Compatible with heavy duty hex bolts up to 3/8” for additional strength
Perfect for mounting on concrete block or other difficult materials
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
1.5 Inch
144 Inch
Any
5/8 Inch
1 1/8 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MFSTR-1125
1/4” x 20 Hex Bolt for Minor Height Adjustments
MFSTR-1125 System
1 2
1
2
1.125
Ø.250 THRU
2.625
2.000
1.49
.750
1.5001.145
(Available in lengths up to 144”)
Standard Z Clips
Cladding Applications
5/8” Lift Off
1 1/8” Projection
FEATURES
14 (631)750-3000 www.monarchmetal.com
MO
NA
RC
H Z
CL
IPS
Heavy DutyStainless Steel ClipsFeatures
High strength, corrosion resistant stainless steel material makes these perfect for use in exterior wet or harsh environments
7/8” clearance required between the top of the panel and the ceiling
Available in 304 Stainless Steel and 316 Marine Grade Stainless Steel
Same simple engagement mechanism as our original Monarch Clips
1/4” Projection
3/4” Lift off1 1/2” Length
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Stainless Steel
1 1/2 Inch
48 Inch
Any
3/4 Inch
1/4 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MFSS HD Clips
Heavy Duty MFSS Clip
1
1
MONARCH
Stainless Steel Hidden Fastening Systems
High Strength Corrosion Resistant Applications
3/4” Lift Off
1/4” Projection
FEATURES
15(631)750-3000 www.monarchmetal.com
MO
NA
RC
H Z
CL
IPS
Stainless Steel Systemwith 1” ProjectionFeatures
High strength, corrosion resistant stainless steel material compatible with up to a 3/8” hex bolt
7/8” clearance required between the top of the panel and the ceiling
304 Stainless steel
1” projection for building envelope applications
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Stainless Steel
3 1/2 Inch
48 Inch
Any
3/4 Inch
1 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MFSSCHAN
MFSSCHAN Bracket
MFSSCHAN1 2
1
2
.75
1.00
.063
1.00
Stainless Steel Hidden Fastening Systems
High Strength Corrosion Resistant Applications
3/4” Lift Off
1” Projection
FEATURES
16 (631)750-3000 www.monarchmetal.com
MO
NA
RC
H Z
CL
IPS
MFTH-625Features
Monarch Z Clip system for hanging interior panels where the installer desires a 5/8” length of engagement
3/4” clearance required between the top of the panel and the ceiling
6063-T6 Aluminum
.250” Projection
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
2 Inch
72 Inch, 144 Inch
Any
5/8 Inch
1/4 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MFTH-625
MFCUSTOM-625MFTH-625
Wall
Panel
MONARCH5/8 Lift off
2” Length
Specialty Z Clips
Standard Applications
5/8” Lift Off
1/4” Projection
FEATURES
17(631)750-3000 www.monarchmetal.com
MO
NA
RC
H Z
CL
IPS
MFEXT-1250Features
Monarch Z Clip system for hanging interior panels where the installer desires a 1 1/4” or 1 3/8” projection
3/4” clearance required between the top of the panel and the ceiling
6063-T6 Aluminum
1.25” Projection
7/8” Lift off
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
Mates with MFTH-625 or MFPROJ-375
120 Inch
Any
7/8 Inch
1 3/8 Inch or 3/8 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MFEXT-1250
Specialty Z Clips
Standard Applications
Lift Off Varies
1/4” Projection
FEATURES
MFPROJ-375
Panel
MFEXT-1250Wall
Shlm
120” Length
18 (631)750-3000 www.monarchmetal.com
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
2 Inch
Mates with MF-EXT1250
Any
5/8 Inch
1 3/8 Inch or 3/8 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MFEXT-1250
MO
NA
RC
H Z
CL
IPS
MFPROJ-375Features
Monarch Z Clip system for hanging interior panels where the installer desires a 1 3/8” projection
3/4” clearance required between the top of the panel and the ceiling
6063-T6 Aluminum
3/8” Projection
Specialty Z Clips
Standard Applications
Lift Off Varies
1 3/8” Projection
FEATURES
MFPROJ-375
Panel
MFEXT-1250Wall
Shlm
5/8” Lift off
2” Length
19(631)750-3000 www.monarchmetal.com
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
Mates with MF375-2 Clip
120”
Any
5/8 Inch
7/16 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MFPROJ-438
MO
NA
RC
H Z
CL
IPS
MFPROJ-438Features
Monarch Z Clip system for hanging interior panels where the installer desires a 7/16” projection
3/4” clearance required between the top of the panel and the ceiling
6063-T6 Aluminum
7/16” Projection
5/8” Lift off
120” Length
Specialty Z Clips
Standard Applications
Lift Off Varies
1 3/8” Projection
FEATURES
Panel
MF375
MFPROJ-438
Wall
Shim
20 (631)750-3000 www.monarchmetal.com
Monarch Z Clip system for hanging interior panels where the installer desires to use a high strength, undercut anchor
1/2 inch clearance required between the top of the panel and the ceiling
Undercut anchors, such as the Keil Undercut anchors often have centri- cal pull fracture loads of more than 750 pounds* when properly installed
Undercut anchors have been utilized with TAKTL panels, GFRC panels, high-pressure laminate, terracotta and stone
6063-T6 Aluminium
*Fracture loads vary widely depending upon the material
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
2 Inch
72 Inch, 144 Inch
Any
7/16 Inch
1/2 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MFSTR050
MO
NA
RC
H Z
CL
IPS
MFSTR-050 for Undercut AnchorFeatures
Ø.365 HEX THRU
.525
1.000
2.000
1/2” Projection
7/16”Lift Off
Specialty Z ClipsApplications Requiring Undercut Anchor
7/16” Lift Off
1/2” Projection
FEATURES
MFSTR-050-2 Custom (9mm Hex Hole)
Keil Undercut Anchor
Panel
Shlm
Wall
21(631)750-3000 www.monarchmetal.com
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Lift Off (1)
Projection (2)
Availability
Aluminum
2 Inch
72 Inch, 144 Inch
Any
3/8 Inch
.293 Inch
Same Day Shipping
(1) The “Lift-Off” is the amount you need to raise the panel over its resting height to mount the panel.
(2) The “Projection” is the distance that the panel sits out from the wall.
MFTAPE
MO
NA
RC
H Z
CL
IPS
MFTAPEFeatures
Easily used for mounting phenolic, ACM, aluminum, mirrors and glass panels
Each 1 ft of clip is rated for 7.5 pounds of shear strength using a 5x factor
Suitable for interior and exterior applications (examples in 3M design guide)
1/2” clearance required between top of the panel and the ceiling
6063-T6 aluminum
(2) strips of 3M VHB architectural panel tape pre-applied for peel and stick application
Pairs with MF375 clip for material savings
Redesign of clip to optimize adhesion with tapes
Clip can also be purchased without 3M tape for use with your preferred vendor of glazing tape
.250
3.375
Available in StockLength of 144”or Cut to Size
.375
1.260
1.260
Hidden Fastening System with 3M High Strength Tape
For Glass, HPL & ACM Panels
3/8” Lift Off
1/4” Projection
FEATURES
5 mm Panel
0.063” Thick Tape
MFTAPE Bracket
MF375 Clip
1
2
1
2
MONARCH
22 (631)750-3000 www.monarchmetal.com
Interlocking clips prevent movement of the panel vertically and horizontally
Removable
Manufactured from 16 Gauge Galvanized Steel
Available in stainless steel
4 interlocking clips are mounted on the back of the panel and 4 interlocking clips are mounted to the ceiling
Material
Stock Clip Size
Stock Continuous Length
Custom Lengths Available
Availability
16 Ga. Galvanized
1 1/2 Inch
Mates with itself
Any
Same Day Shipping
MFCEIL-H
MO
NA
RC
H Z
CL
IPS
MFCEIL-H Ceiling Systemfor Typical Conditions
Features
Ceiling Systems - Typical Conditions
Ceiling Panel
CeilingCeiling
1.5”
23(631)750-3000 www.monarchmetal.com
Ceiling Panel
CeilingCeiling
3.375”
Interlocking clips prevent movement of the panel vertically and horizontally
Removable
Manufactured from 16 Gauge Galvanized Steel
Available in stainless steel
4 interlocking clips are mounted on the back of the panel and 4 interlocking clips are mounted to the ceiling
Concealed and exposed façade / rain screen panel installation systems
Solutions for Ultra High Performance Concrete, Glass Fiber Reinforced Concrete and other manufactured stone
Systems compatible with a variety of undercut anchors and other solutions
Features
Cs
Cs
47(631)750-3000 www.monarchmetal.com
CL
AD
DIN
G
City Square MortselArchitect : Abscis ArchitectenProject Year : 2014EQUITONE [tectiva] facade material
Typical Systems
Thermally Isolated Systems
Vertical Rail
Vertical Rail Horizontal Rail
Exposed Fastener oncealed Fasteners
Exposed Fastener oncealed Fasteners
Exposed Fasteners Concealed Fasteners
Fiber Cement
Concealed and exposed façade / rain screen panel installation systems
Solutions for fiber cement panel installations
Systems compatible with a variety of fasteners including color matched exposed fasteners, concealed undercut anchors and concealed rivet type anchors
Features
Cs
Cs
48 (631)750-3000 www.monarchmetal.com
CL
AD
DIN
G
Concealed fastener mounting system
Available in 304 and 316 stainless steel
Rail available in lengths up to 10’ in 11 Ga. and 16 Ga. stainless steel
Clips can be drilled to accommodate various fasteners for connecting the clip to the back side of the panel, including high strength, undercut anchors
Can be manufactured with 2 holes or 1 hole per clip
Clips offered with a panel height adjustment mechanism
Undercut anchors, such as the Keil Undercut anchors often have centrical pull fracture loads of more than 750 pounds* when properly installed
Undercut anchors have been utilized with TAKTL panels; GFRC panels, high-pressure laminate, terracotta and stone *Fracture loads vary widely depending upon the material
Stainless Steel - Exclusively Available
at MonarchMFSTR-SSCLAD Concealed Fastener SystemFeatures
Stainless Steel Concealed Fastener Rail & Bracket
49(631)750-3000 www.monarchmetal.com
CL
AD
DIN
G
Honeycomb / Sandwich Panels with Stone Veneer
Patented fastening system to securely install honeycomb panels in ventilated rain screen applications
Panel bracket designed so that the bracket is flush with the back of the panel
Adjustable system from Specialinsert is suitable for any kind of material (honeycomb, foam) and thickness
Features
High Performance for Structural Applications
Simple, Easy Installation
Secure installation through the combination of a threaded insert ready to receive a bolt
Properly installed anchors can hold up to 100 KG
100Kg
Bore a cylindrical or hexagonal hole suitable for accommodating the
Screw the tool intothe andexecute the deformation
Deform-Nut®
Insert the into the hole and activatewith the fitting tool
On removal of the toolthe is readyto receive the screw
Deform-Nut®
Deform-Nut®Deform-Nut®
12
34
50 (631)750-3000 www.monarchmetal.com
CL
AD
DIN
G
GFRC Insert System
2.52” 1.0000”
1.0000” 2.0000”
0.2500”
0.1250”0.1250”
1.10”
2.52”
1.250”
110-000 J Channel MFSTR-LW1250-RAIL
MFSTR-LW1250-1.5ADJ
MFSTR-LW1250-1.5ADJ
1.500”
Top-down view Section view
MFSTR-LW1250-1.5ADJ
MFSTR-LW1250-RAILSheating
Panel
Concealed fastener attachment system for GFRC panels in back ventilated rain screen applications with the Monarch MFSTR-LW1250 System
Cast in place insert from various sources embedded in the GFRC panel during the casting process
Available punched for metal stud or concrete wall substrate
1 ½’’ Adjustment Range to Shim the Rail for Plumbness
Range of stock sizes available in addition to custom sizes not listed here
Pairing L Rail or T Rail in Black
Features
HWB-02
HWB-03
HWB-04
HWB-05
2.0’’
3.0’’
4.0’’
5.0’’
2.0’’
3.0’’
4.0’’
5.0’’
3.0’’
4.5’’
5.5’’
6.6’’
Metal Stud, Concrete
Metal Stud, Concrete
Metal Stud, Concrete
Metal Stud, Concrete
Part Name Projection Adjustable Min Adjustable Max Wall Substrate
58 (631)750-3000 www.monarchmetal.com
CL
AD
DIN
G
Stock Vent Screen
110-002 1”Vent Screen
210-001 2.25”Vent Screen
0.250”
1.000”
0.625”
1.000”
0.125”
0.5833”
120.000”
0.750”
0.2917”
0.250”
120.000”
0.9640” TYP.
0.125”
0.4125”
0.4125”
0.4980”
0.4750”
0.4750”0.7500”
0.4750”
2.2500”
0.0625”
1.0000”
Made to Order (Custom)• Wide range of possible sizes• Choice of mill, painted or powder coated finishes• Choice of lengths• Allows for air flow behind rain screen panels
when necesary
A
Bt
• •
•
0.500
0.750
1.000
1.250
1.500
1.750
2.000
2.250
2.500
2.750
3.000
3.250
3.500
3.750
4.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
A B t• •
•
59(631)750-3000 www.monarchmetal.com
Stock System Closure
0.500
0.750
1.000
1.250
1.500
1.750
2.000
2.250
2.500
2.750
3.000
3.250
3.500
3.750
4.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
0.063
A B t
000-003 1” System Closure
Made to Order (Custom)
210-000 2.25” System Closure
• Wide range of possible sizes• Choice of mill, painted or powder coated finishes• Choice of lengths• For closing drained and black ventilated rain
screen systems without air flow
A
Bt
1.000”
1.000”
0.625”
1.000”
2.250”
0.625”
CL
AD
DIN
G
60 (631)750-3000 www.monarchmetal.com
CL
AD
DIN
G
Hat Channel (Vented & Non-Vented)
Material : Galvanized Steel, Aluminum, & Stainless SteelType : Fabricated from SheetStd Lengths : 10’Custom : Custom sizes available, available with ventilation
holes or without
B
A
1.00 1.00
1/2
1
2 1/2
4
2 1/2
4
2 1/2
4
2 1/2
4
1 1/2
2
16 Ga. (.063”) or 18 Ga. (.051”)
16 Ga. (.063”) or 18 Ga. (.051”)
16 Ga. (.063”) or 18 Ga. (.051”)
16 Ga. (.063”) or 18 Ga. (.051”)
16 Ga. (.063”) or 18 Ga. (.051”)
16 Ga. (.063”) or 18 Ga. (.051”)
16 Ga. (.063”) or 18 Ga. (.051”)
16 Ga. (.063”) or 18 Ga. (.051”)
DIMENSIONA
DIMENSIONB
THICKNESSt
61(631)750-3000 www.monarchmetal.com
DIMENSIONA
DIMENSIONB
THICKNESSt
CL
AD
DIN
G
Z Girts (Vented & Non-Vented)
Material : Galvanized Steel, Aluminum, & Stainless SteelType : Fabricated from SheetStd Lengths : 10’Custom : Custom sizes available, available with ventilation
holes or without
A
B
62 (631)750-3000 www.monarchmetal.com
DIMENSIONA
DIMENSIONB
THICKNESSt
Z Girts with Lip (Vented & Non-Vented)
Material : leetS sselniatS & ,munimulA ,leetS dezinavlaG Type : Fabricated from SheetStd Lengths : 10’Custom : Custom sizes available, available with ventilation
holes or without
A
B
CL
AD
DIN
G
63(631)750-3000 www.monarchmetal.com
Material : leetS sselniatS & ,munimulA ,leetS dezinavlaG Type : Fabricated from SheetStd Lengths : 10’Custom : Custom sizes available, available with ventilation
holes or without
B
A
DIMENSIONA
DIMENSIONB
THICKNESSt
C Channel (Vented & Non-Vented)
CL
AD
DIN
G
64 (631)750-3000 www.monarchmetal.com
DIMENSIONA
DIMENSIONB
THICKNESSt
C Channel with Lip (Vented & Non-Vented)
CL
AD
DIN
G
Material : leetS sselniatS & ,munimulA ,leetS dezinavlaG Type : Fabricated from SheetStd Lengths : 10’Custom : Custom sizes available, available with ventilation
• Note that the height of the cap varies with the diameter• Custom sizes are available• Specify threaded connector length when ordering
B
A
5/16” - 18Tapped Hole
Standart
Low Profile
Ordering Notes
• Low pro le caps require a 1/2” hole for installation• Specify threaded connector length when ordering
B
.4
95
.25
0
A
5/16” - 18Tapped Hole
Dia. (A)
Dia. (A)
Height (B)
Height (B)
SO-AL-1LPCAP
SO-AL-1.25LPCAP
SO-AL-1.5LPCAP
SO-AL-2LPCAP
SO-AL-1CAP
SO-AL-1.25CAP
SO-AL-1.5CAP
SO-AL-2CAP
Part No.
Part No.
1”
1 1/4”
1 1/2”
2”
1”
1 1/4”
1 1/2”
2”
3/8” Total (1/8” Exposed)
3/8” Total (1/8” Exposed)
3/8” Total (1/8” Exposed)
3/8” Total (1/8” Exposed)
3/8”
1/2”
1/2”
5/8”
68 (631)750-3000 www.monarchmetal.com
ST
AN
DO
FF
S
Stainless Steel Cap
Stainless Steel Cap
Standart
Low Profile
Ordering Notes
• Standard stainless caps require a 7/16” hole for installation• Custom sizes are available• Specify threaded connector length when ordering
.18
8
B
.43
7
A
5/16” - 18Tapped Hole
Ordering Notes
• Low pr require a 1/2” hole for installation• Specify threaded connector length when ordering
B
.4
95
.25
0
A
5/16” - 18Tapped Hole
Dia. (A)
Dia. (A)
Height (B)
Height (B)
SO-SS-1LPCAP
SO-SS-1.25LPCAP
SO-SS-1.5LPCAP
SO-SS-2LPCAP
SO-SS-1CAP
SO-SS-1.25CAP
SO-SS-1.5CAP
SO-SS-2CAP
Part No.
Part No.
1”
1 1/4”
1 1/2”
2”
1”
1 1/4”
1 1/2”
2”
3/8” Total (1/8” Exposed)
3/8” Total (1/8” Exposed)
3/8” Total (1/8” Exposed)
3/8” Total (1/8” Exposed)
3/8” Total (3/16” Exposed)
3/8” Total (3/16” Exposed)
3/8” Total (3/16” Exposed)
3/8” Total (3/16” Exposed)
69(631)750-3000 www.monarchmetal.com
ST
AN
DO
FF
S
Ordering Notes
• Security caps require a 7/16” hole for installation• (2) 3/32” holes for tightening with spanner wrench
B
.18
8
.4
37
A
5/16” - 18Tapped Hole
Ordering Notes
• Please note that you are ordering the “No Stem” cap when ordering• Custom heights available• Specify threaded connector length when ordering
A
5/16” - 18Tapped Hole
B
Stainless Steel Cap
Stainless Steel CapNo Stem
Security Cap
Dia. (A)
Dia. (A)
Height (B)
Height (B)
SO-SS-1SECCAP
SO-SS-1.25SECCAP
SO-SS-1.5SECCAP
SO-SS-2SECCAP
SO-SS-1NSCAP
SO-SS-1.25NSCAP
SO-SS-1.5NSCAP
SO-SS-2NSCAP
Part No.
Part No.
1”
1 1/4”
1 1/2”
2”
1”
1 1/4”
1 1/2”
2”
3/8” Total (3/16” Exposed)
3/8” Total (3/16” Exposed)
3/8” Total (3/16” Exposed)
3/8” Total (3/16” Exposed)
3/8”
1/2”
1/2”
5/8”
70 (631)750-3000 www.monarchmetal.com
Aluminum Barrels
ST
AN
DO
FF
S
Standard
Ordering Notes
• Custom heights available
while 2” barrels and taller are tapped approximately
B
A
5/16” - 18Tapped Hole
Both Ends
Dia. (A)
1”
2”
3”
4”
6”
Part No.
SO-AL-1BL-1
SO-AL-1BL-2
SO-AL-1BL-3
CUSTOM
CUSTOM
SO-AL-1.25BL-1
SO-AL-1.25BL-2
SO-AL-1.25BL-3
CUSTOM
CUSTOM
SO-AL-1.5BL-1
SO-AL-1.5BL-2
SO-AL-1.5BL-3
CUSTOM
CUSTOM
SO-AL-2BL-1
SO-AL-2BL-2
SO-AL-2BL-3
CUSTOM
CUSTOM
1” Dia.Height (B) 1 1/4” Dia. 1 1/2” Dia. 2” Dia
71(631)750-3000 www.monarchmetal.com
Stainless Steel Barrels
ST
AN
DO
FF
S
Standard
Ordering Notes
• Custom sizes are available• Stainless Barrels up to 1.5” in height are tapped thru, while 2” barrels and taller are tapped approximately 3/4” from each end
B
A
5/16” - 18Tapped Hole
Both Ends
Dia. (A)
1”
1 1/2”
2”
3”
4”
6”
Part No.
SO-SS-1BL-1
SO-SS-1BL-1.5
SO-SS-1BL-2
SO-SS-1BL-3
CUSTOM
CUSTOM
SO-SS-1.25BL-1
SO-SS-1.25BL-1.5
SO-SS-1.25BL-2
SO-SS-1.25BL-3
CUSTOM
CUSTOM
SO-SS-1.5BL-1
SO-SS-1.5BL-1.5
SO-SS-1.5BL-2
SO-SS-1.5BL-3
CUSTOM
CUSTOM
SO-SS-2BL-1
SO-SS-2BL-1.5
SO-SS-2BL-2
SO-SS-2BL-3
CUSTOM
CUSTOM
1” Dia.Height (B) 1 1/4” Dia. 1 1/2” Dia. 2” Dia
72 (631)750-3000 www.monarchmetal.com
Mounting Hardware
Also AvailableST
AN
DO
FF
S
with Anchor
Ordering Notes
• Custom sizes are available• Ask for assistance from your sales representative
B
A B A C C
Option A
Option B
Option C
Option A
Option B
Option C
HB-A
HB-B
HB-C
TT-A
TT-B
TT-C
1 1/2”
2 1/2”
4”
1” Thick Surface
1.25” Thick Surface
1.75” Thick Surface
5/8”
1”
2”
7/8”
1 1/2”
2”
Hanger Bolts
Tabletop Screw with Anchor
Part Number
Part Number
Overall
Surface Thickness
Machine Thread Wood Screw
ARCHITECTURALMETALS
Angle: Aluminum, Stainless
and Steel ..................................................... 65 .
Channel: Aluminum, Stainless
and Steel ...................................................... 64
Flat Bar: Aluminum, Stainless
and Steel ..................................................... 67
STAINLESS STEEL ANGLEEqual & Unequal Leg Steel Angle
Alloy : 304 or 316 AlloyType : Equal Legs & Unequal LegsStd Lengths : 20'Custom : Available Punched with Holes or Cut to LengthFinishes : Mill, Brushed, Mirror Polished
80 (631)750-3000 www.monarchmetal.com
DIMENSIONA
DIMENSIONA
DIMENSIONB
DIMENSIONB
THICKNESSt
THICKNESSt
Alloy : Mild SteelType Std Lengths Custom : Available Punched with Holes or Cut to LengthFinishes : Mill
AR
CH
ITE
CT
UR
AL
ME
TA
LS
STEEL ANGLEEqual & Unequal Leg Steel Angle
81(631)750-3000 www.monarchmetal.com
DIMENSIONA
DIMENSIONA
DIMENSIONB
DIMENSIONB
THICKNESSt
THICKNESSt
Alloy : Mild SteelType Std Lengths Custom : Available Punched with Holes or Cut to LengthFinishes : Mill
AR
CH
ITE
CT
UR
AL
ME
TA
LS
STEEL ANGLEEqual & Unequal Leg Steel Angle
82 (631)750-3000 www.monarchmetal.com
DIMENSIONA
DIMENSIONA
DIMENSIONB
DIMENSIONB
THICKNESSt
THICKNESSt
Alloy : Mild SteelType Std Lengths Custom : Available Punched with Holes or Cut to LengthFinishes : Mill
Alloy : 6063 AluminumType : ASTM B 221Std Lengths : 16', 8'Custom : Available Punched with Holes or Cut to LengthFinishes : Mill, Brushed Finish, Anodized, Mirror Polished
DIMENSIONA
DIMENSIONA
THICKNESSt
THICKNESSt
92 (631)750-3000 www.monarchmetal.com
DIMENSIONA
DIMENSIONA
THICKNESSt
THICKNESSt
AR
CH
ITE
CT
UR
AL
ME
TA
LS
Stainless Steel Flat Bar
Alloy : 304 or 316 AlloyType : ASTM A 276/479Std Lengths : 12'Custom : Available Punched with Holes or Cut to LengthFinishes : Mill, Brushed Finish, Mirror Polished
Alloy : 304 or 316 AlloyType : ASTM A 276/479Std Lengths : 12'Custom : Available Punched with Holes or Cut to LengthFinishes : Mill, Brushed Finish, Mirror Polished
Alloy : 304 or 316 AlloyType : ASTM A 276/479Std Lengths : 12'Custom : Available Punched with Holes or Cut to LengthFinishes : Mill, Brushed Finish, Mirror Polished
95(631)750-3000 www.monarchmetal.com
FLAT BARBrass Flat Bar
- 69 -
DIMENSION
ATHICKNESS
t
Alloy : 360 AlloyType : ASTM B 16Std Lengths : 12'Custom : Available Punched with Holes or Cut to LengthFinishes : Mill, Brushed Finish, Mirror Polished
DIMENSION
ATHICKNESS
t
1/8 x 1/83/161/45/163/81/25/83/47/8
11 1/41 1/21 3/4
22 1/42 1/2
33 1/2
4
3/16 x 3/163/81/25/83/47/8
11 1/4
1 1/21 3/4
2
2 1/2
3/16 x 33 1/2
4
1/4 x 1/45/163/81/25/83/47/8
11 1/41 1/21 3/4
22 1/22 3/4
33 1/2
4
5/16 x 5/163/81/25/83/4
11 1/41 1/2
www.monarchmetal.com/products/brass-flat-bar/Brass Flat BarBrass Flat Bar
Alloy : 304 Stainless, Aluminum, Diamond PlateType : 16 Gauge (Standard), 14 Ga., 18 Ga.Std Lengths : 4', 8'Custom : Available Punched with Holes or Cut to LengthFinishes : Brushed Finish, Mirror Polished
• Custom Shapes & Sizes Available •
• Please Call 631-750-3000 •
1 1/4 x 48 x 1/16 CORN1.25x48 16 Ga Stainless Steel, Adhesive Mounted1 1/4 x 96 x 1/16 CORN1.25x961 1/2 x 48 x 1/16 CORN1.5x481 1/2 x 96 x 1/16 CORN1.5x962 1/2 x 48 x 1/16 CORN2.5x482 1/2 x 96 x 1/16 CORN2.5x963 1/2 x 48 x 1/16 CORN3.5x483 1/2 x 96 x 1/16 CORN3.5x96
90 Angle˚
Bullnose3 1/2 x 48 x 1/16 BCORN3.5x483 1/2 x 96 x 1/16 BCORN3.5x96
90°SharpAngle
90°Rounded
Angle
A
t
B
t
A
B
16 Ga Stainless Steel, Adhesive Mounted16 Ga Stainless Steel, Adhesive Mounted16 Ga Stainless Steel, Adhesive Mounted
16 Ga Stainless Steel, Adhesive Mounted16 Ga Stainless Steel, Adhesive Mounted16 Ga Stainless Steel, Adhesive Mounted
16 Ga Stainless Steel, Adhesive Mounted
16 Ga Stainless Steel, Adhesive Mounted16 Ga Stainless Steel, Adhesive Mounted
Alloy : 304 Stainless, Aluminum, Bronze, BrassType : 18 Gauge (Standard), 16 Ga., 11 Ga.Std Lengths : See BelowCustom : Available with Rough Finish for Adhesive, Punched,
or Punched & CountersunkFinishes : Mill, Brushed Finish, Mirror Polished
• Custom Shapes & Sizes Available •
• Please Call 631-750-3000 •
24 x 34 x 18 Ga. KICK24x3428 x 6 x 18 Ga. KICK28x628 x 8 x 18 Ga. KICK28x828 x 10 x 18 Ga. KICK28x1028 x 12 x 18 Ga. KICK28x1228 x 36 x 18 Ga. KICK28x3628 x 42 x 18 Ga. KICK28x4230 x 6 x 18 Ga. KICK30x630 x 8 x 18 Ga. KICK30x830 x 10 x 18 Ga. KICK30x1030 x 12 x 18 Ga. KICK30x1234 x 6 x 18 Ga. KICK34x634 x 8 x 18 Ga. KICK34x834 x 10 x 18 Ga. KICK34x1034 x 12 x 18 Ga. KICK34x1234 x 16 x 18 Ga. KICK34x1634 x 34 x 18 Ga. KICK34x3434 x 36 x 18 Ga. KICK34x3634 x 42 x 18 Ga. KICK34x4234 x 46 x 18 Ga. KICK34x4636 x 8 x 18 Ga. KICK36x836 x 10 x 18 Ga. KICK36x1036 x 12 x 18 Ga. KICK36x12
18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes18 Ga Stainless, No Holes
Secure installation through the combination of a threaded insert ready to receive a bolt
NEW PRODUCT
Monarch Metal 1625 Sycamore Ave Bohemia, New York 11716 (631) 750 3000 [email protected] Metal 1700 Ocean Ave Ronkonkoma, New York 11779 (631) 750 3000 [email protected]
Monarch Metal | 1700 Ocean Ave. | Ronkonkoma, New York 11779 | (631) 750 3000 | [email protected]