Transitional Lighting Introduction Walkways & Steplights Building Mounted Parking Garage { Walkways & Steplights T3 - T9 Building Mounted T10 - T14 Parking Garage T15 - T17 WALKWAYS & STEPLIGHTS Walkway and steplights provide low-glare illumination for corridors, stairwells, patios and pathways at hospitals, hotels, schools, airports and parking garages. These luminaires brighten otherwise dark areas to reveal steps, footpaths and wayward debris as well as keeping the area safe for pedestri- ans at night. BUILDING MOUNTED Building-mounted lighting enhances the aesthetic appearance of buildings at night. Luminaires are typically mounted and aimed to illu- minate the structure, ideally used for general illumination in rough service (vandal-resistant) applications in both the interior and exterior where safety and security are a concern. PARKING GARAGE A parking garage is an enclosed or covered parking structure. Lithonia Lighting products are optically designed around the unique character- istics of these spaces—rugged, heavy-duty construction; vandal-resistant; working in wet locations and during extreme temperatures— while allowing uniform illumination to provide safety and to assist with the location of vehicles.
16
Embed
Walkways & Steplights Building Mounted Parking … Hospitality Selection Guide Transitional Lighting Introduction Walkways & Steplights Building Mounted Parking Garage
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transitional Lighting IntroductionWalkways & Steplights Building Mounted Parking Garage
{ Walkways & Steplights T3 - T9
Building Mounted T10 - T14
Parking Garage T15 - T17
WALKWAYS & STEPLIGHTSWalkway and steplights provide low-glare illumination for
corridors, stairwells, patios and pathways at hospitals, hotels,
schools, airports and parking garages. These luminaires
brighten otherwise dark areas to reveal steps, footpaths and
wayward debris as well as keeping the area safe for pedestri-
ans at night.
BUILDING MOUNTEDBuilding-mounted lighting enhances the aesthetic appearance of buildings at night. Luminaires are typically mounted and aimed to illu-
minate the structure, ideally used for general illumination in rough service (vandal-resistant) applications in both the interior and exterior
where safety and security are a concern.
PARKING GARAGEA parking garage is an enclosed or covered parking structure. Lithonia Lighting products are optically designed around the unique character-
istics of these spaces—rugged, heavy-duty construction; vandal-resistant; working in wet locations and during extreme temperatures—
while allowing uniform illumination to provide safety and to assist with the location of vehicles.
Hospitality Selection Guide www.acuitybrandslighting.com T3
Nominal Number Lamp Heightsize Series of lamps type Width in. Length7.5”x4’ FTS4 1,2,3 28T5, 54T5HO 7.5” 4” 48”7.5”x8’ FTS8 1,2 32 7.5” 4” 96”1’x4’ FHI4 2,3 28T5, 54T5HO 11” 6.5” 48”1’x8’ FHI8 2,3 32 11” 6.5” 96”
Ordering Information Example: Fts8 2 54t5Ho t1X20 BaF75 Mvolt GeB10Ps
Walkways & Stairwell Fixture
FCIIntended Use
SpecLight FCI Series luminaires are designed for maximum energy efficiency for walkways, stair-wells or hospitality environments. The integral mo-tion sensors and compact fluorescent night light option provide greater specification flexibilty.
Features
High fixture efficiency and optical control deliver the peak candle power needed to produce non-glare illumination levels from low mounting heights. Improved horizontal illumination.
Long-life - up to 30,000 hours.
Channel, ends and socket brackets are manufac-tured from 22-gague cold-rolled steel. Optional 20-gague construction.
All standard ballasts are electronic, energy saving, thermally protected, ClassP, HPF, non-PCB, Sound Rated A. Default ballast configuration for two-lamp ballasts.
UL listed wire, rated for required temperatures, used throughout. Lamps are secured with rotary locking sockets for ease of relamping and to re-
Series
FTS4 7.5”x4’ FTS8 7.5”x8’ FHI4 1’x4’ FHI8 1’x8’
Ballast type
GEB10PS Normal BF<10% THD, PS GEB10PSH High BF, <10% THD, PS GEB10PSL Low BF, <10%
SNUT3 Ultrasonic stairwell, wall sensor SNR4 360 infrared ceiling mount SNS4 360 infrared ceiling mount
Night Light
(blank) No night light 1CF9 9W Compact
fluorescent
Lamp type/Wattage
17 FO17T8 32 FO32T8
NOTES:1 Specific voltage required for night light.2 Sensors wired to toggle between night light and normal when used with ICF9
option, add Z for use with night light.3 Ultrasonic sensors for wall mount stairwell application.4 Specific voltage required for night light.
Lamp configuration
11 1-lamp profile 2 2-lamp profile
duce lamps diconnecting due to vibration or inci-dental contact and is suitable for damp location.
Standard paint after fabrication premium poly-ester coat finish, utilizing a 7-stage pretreatment process of iron phosphate, a non-chromium sealer and a de-ionized water rinse to provide superior adhesion and corrosion resistance.
Acrylic prismatic diffuser shields the lamp.
Fixture is designed for ceiling or wall surface mount.
Factory installed lamps are available in various CRI ratings, temperature colors and rated life.
Listings
UL Listed wire, rated for required tempera-tures, used throughout. Listed and conforms to UL 1598 and CSA. Suitable for damp locations.
Custom Solutions
May be modified to meet any custom application. Contact your SpecLight representative for assis-tance.
Rated Non-IC for new construction in indoor ap-plications or outdoor wet locations, such as court-yards and pathways.
Features
Mechanical – Aluminum die-cast, white powder coat paint, corrosion-resistant housing. Louvered, slotted, and open faceplates available. Die-cast powder coat painted faceplates are available in white or black finish. Faceplates are shipped sepa-rately.
Electrical System – 9DTT - Encased and potted, high power factor (HPF) electromagnetic ballast standard (120V only). 13DTTE - High power factor (HPF), -20°F to 158°F, instant start electromagnet-ic ballast standard (120V or 277V). One electrical
Wet Location Steplights
WSL1F
Louvered faceplate
FPL White FPLBL Black
Opal faceplate
FPS White FPSBL Black
9 -3 /4 "
4 -1 /8 "
4 -1 /8 "
Ordering Information Example: Wsl1F 9Dtt FPlBl 120
STANDARD PACKAGINGTo order, use single master catalog number.Example: (12) WSL1F 9DTT FPLBL 120 Fixtures ship as multiple components using optimized packaging. Example above ships as:
(Qty 12) WSL1F 9DTT 120 (12 cartons of 1 housing)(Qty12) FPLBL (12 cartons of 1 faceplate)
Non-IC Rated – These steplights can be used in indoor or outdoor wet locations using lamps and wattages listed.
Drawings are for dimensional detail only and may not represent actual mechanical configuration. Dimensions are shown in inches.
9DTT13DTT 4-PIN
Slotted faceplate
FPS White FPSBL Black
9DTT13DTT 4-PIN
9DTT13DTT 4-PIN
Series
WSL1F
Wattage/lamp
9DTT1
13DTTE2
Faceplates
FPL White louvered FPLBL Black louvered FPS White slotted FPSBL Black slotted FPO White opal FPOBL Black opal
Voltage
120277
NOTES:1 120V only.2 Electronic ballast standard.
conduit fitting and one plug provided. Electrical conduit fitting for wet location in wood construc-tion, masonry and poured concrete applications.
White BlackIncandescent 25 A19 (IC )40 A19 (Non-IC)
Fluorescent13DTT (IC)
9-1/2"
5"
IC/Non-IC Rated – These steplights are damp location listed. Maximum wattage and lamps are listed.
10-1/4"
3-1/2"
10-1/4"
3-1/2"
Intended Use
Recessed housing rated IC or Non-IC for new con-struction applications. For indoor use only.
Features
Approved for through-branch circuit wiring.Galvanized steel housing and wiring compart-ment with a ground wire. Bar hangers span 16" with recessed integral nailer tabs. Powder-coated steel louver available in white or black finish. Butterfly springs hold louver se-curely in place. Die-cut foam gasket seals steel louver against surface, preventing light leaks. Encased-and-potted, normal power factor (NPF) electromagnetic ballast standard (Fluorescent only).
Listings
UL Listed to U.S. and Canadian safety standards.
9-1/2"
5"
10-1/4" 3-1/2"
Ordering Information Example: sl1F 9Dtt Bl
Series
SL1F
Faceplate
Wattage/Lamps
9DTT13DTT
Drawings are for dimensional detail only and may not represent actual mechanical configuration. Dimensions are shown in inches.
Ordering Information Example: 4462 2/M35 12 FL RG CSL50 LPI
Cord set length
CSL ___ 35’-120’ of cord4
NOTES:1 Transformer sold separately.2 Only available with 2/M35.3 Accessories are mutually exclusive. Choose
one.4 CSL50 is maximum length for 12V
fixtures.
steP
liG
Hti
nG
5-3/8(137)
6-7/8(175)
11 (279)
Lamp
LPI Lamp included
Pathway Light
4462
Intended Use
Meets installation requirements for wood and all (insulation) type IC applications. Fixtures are completely weatherproof with neoprene gasket and tempered lens.
Ordering Information Example: 4456 A 42TRT 120 EL N LPI DDB
Accessories
External LLV7 Louver door
Lamp type
Incandescent75I2,3
Fluorescent3
18TRT26TRT32TRT42TRT
Metal halide50M
High pressure sodium35S2
50S
Finish
BL Black BZ Bronze DDB Dark bronze DNA Natural aluminum GN Green GR Gray SND Sand STG Steel gray TVG Terra verde
green WH White CF Custom
Product
44544456
Material
A Aluminum B Bronze1
Voltage
120277347
MVOLT5
Intended Use
For use in outdoor wet locations, such as patios and pathways at hospitals, hotels, schools, airports and parking garages.
MaterialCast aluminum or cast bronze. Alumi-num body black permabarred.
LampHID: 50W max, E17 lamp.
SocketMedium screw base, pulse-rated.
BallastHID: Magnetic ballast high power factor with -20° F (-29° C) minimum starting temperature. Fluorescent: electronic ballast high frequency with 0° F (-18° C) minimum starting temperature.
LensDiffused, tempered glass for non-louvered door. Clear, tempered glass for louvered door.
Conduit Entries3/4” NPT side entries standard.
FastenerStainless steel.
ListingsU.L., CSA, suitable for wet locations.
Options3,4
ELN5 NICAD battery backup
SF Single fuse6
NOTES:1 Not available with the 4456.2 Available in 120V only.3 Not available with 4454.4 Only available with fluorescent lamps.5 Only valid with 18TRT, 26TRT, 32TRT, and
42TRT.6 Only available with MH and HPS lamps.7 Only available with clear lens.
Low profile (ADA) VGO1 3.7" deep VGO2 4" deep VGO3 4" deep VGO4 4.1" deep1
VGO5 4" deep
Lamp type
Twin-tube2
13TTDouble twin-tube
13DTT 18DTT 26DTT
Triple-tube 26TRT 32TRT
Ordering Information Example: vGo1 32trt Mvolt DWHG trs lPi
Paint finishes5
Standard textured colors DWHG White DBLB Black DDBT Dark bronze DNAT Natural aluminum DSST SandstoneOptional textured colors DBNH Bronze DSPD Dark gray DSPE Green DSPG Dark red DSPF Rust DSPH Red DSPJ Light gray
CSA Listed and labeled to comply with Canadian standards NOM NOM Certified
Intended Use
Architectural luminaires for general illumination in rough service (vandal-resistant ) applications. Ideal for interior or exterior applications where safety and security are a concern.
Features
Bezel – One-piece, marine-grade die-cast alumi-num, low copper alloy (<1% copper), .125" thick. Secured to backplate with stainless steel Torx® T10 set screws (two included).
Finish – Standard finish is textured polyester pow-der coat.
Backplate – 16-gauge steel, post-painted in black polyester powder coat. Four-point mounting de-tail.
Lens – Translucent white, injection-molded, UV-stabilized polycarbonate, .125" thick. Smooth ex-terior for easy cleaning. Interior pattern diffuses light for uniform surface illumination. Optional borosilicate glass lens available (.250" thick).
NOTES:1 Not ADA compliant.2 120V only.3 Not available with TRT lamps.4 Multi-volt electronic ballast (for DTT and TRT lamps) capable of operating on
any line voltage between 120V and 277V.5 For additional colors, see Architectural Colors brochure on www.lithonia.
com.6 Must specify voltage. Not available with MVOLT.7 Stainless steel Torx® T20 screws with center reject pin.8 Lamp included unless L/LP is specified.
Steel Backplate, Oval
VGOGateway®
Dimensions are shown in inches (centimeters) unless otherwise noted.
VGO2
VGO3
VGO1
VGO4 VGO5
9.4"(23.8)
6.7"(9.4)
13.7"(34.8)
13.7"(34.8)
13.7"(34.8)
4"(10.2)
9.4"(23.8)
4"(10.2)
9.4"(23.8)
13.7"(34.8)
4.1"(10.4)
4"(10.2)
9.4"(23.8)
9.4"(23.8)
13.7"(34.8)
Lamp/Fixture Data Weight Lamp Wattage Ballast lbs. baseFluorescent
Housing – Rugged, die-cast, single-piece housing. Die-cast door frame has 1/8” thick tempered glass lens. Door frame is fully gasketed with one-piece solid silicone. Standard finish is textured dark bronze (DDBT) corrosion-resistant polyester pow-der with other architectural colors available.
Optics – Interchangeable, segmented reflectors for superior uniformity and control. Three full cutoff distributions available: FT (forward throw), MD (medium throw) and WT (wide throw). Four uplight distributions available in WSR only: FTU (forward throw, 10% up), MDU (medium throw, 10% up), WTU (wide throw, 10% up) and MDU5 (up/down, medium throw, 50% up, 50% down). Compact fluorescent MD (medium throw) only.
Electrical – HID: 50W MH-150W utilizes a high reactance, high-power factor ballast. 35S and 50S utilizes a reactor normal-power factor bal-last. 175W utilizes a constant-wattage auto transformer ballast. Quick-disconnect plug eas-ily disconnects reflector from ballast. Ballasts are copper wound and 100% factory tested. CFL: compact fluorescent ballast is Class P, electron-ic, high-power factor, <10% THD with starting temp. of 0o F (-18o C).
Socket - HID is porcelain, medium-base copper al-loy, nickel-plated screw shell and center contact.
(UL Listed 660W, 600V 4KV pulse rated). Fluores-cent socket is high-temperature thermoplastic with integral lamp retention clip.
Installation – Universal mounting mechanism with integral mounting support allows fixture to hinge down. Bubble level provides correct alignment with each installation.
Listings
UL Listed suitable for wet locations (damp location listed in lens-up orientation). CSA Certified (see Options). IP65 rated.
WSQ
WSR
MRW
WST
Ordering Information Example: Wst 175M Ft 120 sF lPi
NOTES:1 120V only, NPF only2 Only available with MD, MDU and MDU5 distributions.3 Available on WSR fixture only.4 Not available in Canada.5 Optional multi-tap ballast (120V, 208V, 240V, 277V). In Canada 120V, 277V,
347V; ships as 120V/347V.6 Optional 5-tap ballast (120V, 208V, 240V, 277V, 480V; n/a in Canada). 175M
capable of operating on any line voltage from 120V-277V.8 Available for compact fluorescent units only.9 Must specify voltage, n/a MVOLT or TB.10 Not available with SF, DF or QRS.11 Not available with 2/32TRT or 2/42TRT.12 Battery pack by others and mounted external to luminaire. Pilot light/test
switch mounting plate included. Consult factory for availability.13 Not available with compact fluorescent. Maximum allowable wattage lamp
included.14 Black finish only.15 Must be ordered with fixture; no field modifications.16 IBS not available with MD, MDU and MDU5 distributions.17 For WSR, inverted orientation, with FTU and WTU distributions only. 18 Additional architectural colors available; see www.lithonia.com.19 Must specify finish.20 -20°C to 55°C operation. N/A 2/26DTT, 2/32TRT, 2/42TRT ,MRW, WSQ or WSR
For entrances, stairwells, corridors and other pedestrian areas. use in car washes will result in discolor-ation of the polycarbonate lens over time. this will become a maintenance require-ment.
Features
Housing – Rear housing is rugged, die-cast alu-minum. Front cover is one-piece, UV-resistant, injection-molded polycarbonate, internally paint-ed. Captive external hardware is treated for corro-sion resistance and includes slotted hex-head and tamper-proof fasteners. Finish is dark bronze (DDB) corrosion-resistant polyester powder.
Optics – Front housing and refractor are one-piece, injection-molded, UV stabilized polycarbonate. One-piece, die-formed reflector is diffused alumi-num. Refractor is clear polycarbonate, providing ies cutoff distribution and maximum lateral light output. Standard finish is dark bronze poly-ester enamel. Front cover sealed with one-piece, high temperature silicone gasket to inhibit en-trance of outside contaminants.
Ordering Information Example: tWac 100s 120 lPi
NOTES:1 120V only.2 120V or 277V only.3 120V R-NPF is standard, 208/240/277/347 and TB are high reactance highpower
factor.4 Consult factory for availability in Canada.5 Optional multi-tap ballast (120V, 208V, 240V, 277V). In Canada 120V, 277V,
347V; ships as 120V/347V.6 Optional multi-volt electronic ballast (for compact fluorescent) capable of
operating any line voltage from 120V-277V.7 Not available with multi-tap ballast.8 Available with CF only, n/a MVOLT.9 Lamp not included.10 Quartz lamp wattage not to exceed ballast wattage rating.11 Black finish only.12 HID only, n/a QRS, EC or NOM.
inches (centimeters)
Accessories (Order separately)
RK1 PEB1 Photoelectric control kit, 120V RK1 PEB1 CSA Photoelectric control kit, 120V RK1 PEB2 Photoelectric control kit, 208V, 240V or 277V RK1 PEB3 CSA Photoelectric control kit, 347V TWAWG Wireguard
Electrical – MH: High-reactance, high-power fac-tor standard. HPS: Reactor normal power factor standard. HPF available. UL Listed. Electrical com-ponents mounted to the cast aluminum housing, promoting maximum heat dissipation. Fluorescent ballasts are electronic HPF (26 DTT & TRT).
Socket – HID is porcelain, horizontally oriented, medium-base socket with copper alloy, nickel-plated screw shell and center contact. (UL Listed 660W, 600V and 4KV pulse rated.) Fluorescent is 4-pin (TRT), positive latching thermoplastic.
Installation – Top 1/2" threaded wiring access. Back access through 3/4" opening. For feed-thru wiring, use conduit tee (not included). Mount on any flat, non-combustible vertical surface.
Listings
UL Listed (standard). CSA or NOM Certified (see Options). UL Listed for wet locations. IP65 rated.
Nominal Number Lamp Heightsize Series of lamps type Width in. Length7.5”x4’ FTS4 1,2,3 28T5, 54T5HO 7.5” 4” 48”7.5”x8’ FTS8 1,2 32 7.5” 4” 96”1’x4’ FHI4 2,3 28T5, 54T5HO 11” 6.5” 48”1’x8’ FHI8 2,3 32 11” 6.5” 96”
Ordering Information Example: Fts8 2 54t5Ho t1X20 BaF75 Mvolt GeB10Ps
Parking Garage Luminaire
FSWT5HO, T8
Intended Use
The FSW Series is designed for parking structures when mounted parallel with the drive lanes. The luminaire produces a very broad distribution across the drive lane while minimizing glare in the driver’s eyes.
Features
Housing is gasketed fiberglass enclosure that is dust and moisture resistant. Standard shatter-proof Polycarbonate lens is held in place by latches that secure a continuous seal. Internal channels, ends and socket brackets are manufactured from 22-gauge cold-rolled steel, riveted and screwed assembly. Tooless ballast and wiring access.
Finished in high-gloss baked white enamel, pretreated with a 5-stage iron phosphate sys-tem. Optional premium polyester powder coat is available.
Ballasts are electronic, energy-saving, thermally protected, UL Listed, Class P, CSA Certified where applicable, HPF, non-PCB, Sound Rating A. Bal-lasts comply with Federal Ballast Law (Public Law 100-357, 1988).
UL listed wire, rated for required temperatures, used throughout. Lamps are secured with rotary
locking sockets for ease of relamping and to re-duce lamps disconnecting due to vibration or inci-dental contact and is suitable for damp location.
Standard paint after fabrication premium poly-ester coat finish, utilizing a 7-stage pretreatment process of iron phosphate, a non-chromium sealer and a de-ionized water rinse to provide superior adhesion and corrosion resistance.
Acrylic prismatic diffuser shields the lamp.
Fixture is designed for ceiling or wall surface mount.
Factory installed lamps are available in various CRI ratings, temperature colors and rated life.
Listings
UL Listed wire, rated for required tempera-tures, used throughout. Listed and conforms to UL 1598 and CSA. Suitable for damp locations.
Custom Solutions
May be modified to meet any custom application. Contact your SpecLight representative for assis-tance.
NOTES:1 Available only with FTS Series.2 Not available with FTS T8 fixture.3 Available only with FTS T5HO fixture.4 Available only with a normal beam distribution.
Ordering Information Example: FPG4 2 54t5Ho B1X20 Mvolt GeB10Ps lP841
Parking Garage Luminaire
FPGSpecular Reflector
Ballasts are electronic, energy-saving, thermally protected, UL Listed, Class P, CSA Certified where applicable, HPF, non-PCB, Sound Rating A. Bal-lasts comply with Federal Ballast Law (Public Law 100-357, 1988).
The luminaire is designed for surface mounting. Surface conduit entry is available – specify SCE.
Lamps available in various CRI ratings, tempera-ture colors and rated life. Secured with rotary lock-ing lamp sockets to minimize disconnection from vibration or incidental contact.
Listings
UL Listed wire, rated for required temperatures, used throughout. Listed and conforms to UL 1598. Suitable for damp locations.
Custom Solutions
May be modified to meet any custom application. Contact your SpecLight representative for assis-tance.
Nominal Number Lamp size Series of lamps type Width Height Length9”x25” FPG2 17, 14T5, 24T5HO 25” 9”x49” FPG4
2 32, 28T5, 54T5HO
9”
3” 49” 9” wide 2-lamp
NOTES:1 Available only with 2’ fixtures.2 Available only with 4’ fixture.
Intended Use
The FPG Series is designed for parking structures when mounted parallel with the drive lanes. The luminaire produces a very broad distribution across the drive lane while minimizing glare in the driver’s eyes.
Features
The backplate is manufactured from minimum 20-gauge cold-rolled steel, riveted and screwed assembly for rigidity. Optional all aluminum con-struction is available – Specify AL and PAF. Optional heavy-gauge steel backplate is available – specify 18GA or 16GA.
Reflector is precision-formed, high performance, 95% total reflectance, segmented optics utilizing Alanod MIRO® 4 specular aluminum. Warranted for 25 years.
Finished in high-gloss baked white enamel, pretreated with a 5-stage iron phosphate sys-tem. Optional premium polyester powder coat is available.
Options
AL Aluminum construction 18GA 18-gauge backplate
Lamps (factory installed)
(blank) No lamps LP841 85 CRI, 4100°K, standard life LP850 85 CRI, 5000°K, standard lifeAmalgam lamps LP841A 82 CRI, 4100°K, (T5HO only)
NOTES:1 May be ordered with SCWA option.2 Must be ordered with SCWA option.3 Must be ordered with GEB option.4 Must be ordered with LP option. Optimized for use in areas where ambient
temperature does not exceed 20°C. Higher ambient temperatures may reduce lamp life.
5 Consult factory for availability in Canada.6 Not available with induction.7 Available in 150S, 175M and 200M only.8 Not available with compact fluorescent.9 Optional multi-tap ballast 120, 208, 240, 277 (120, 277, 347 for Canada).10 Optional multi-volt electronic ballast capable of operating on any line voltage
from 120V-277V. Use for both compact fluorescent and electronic HID.11 Available in compact fluorescent, 50M, 50MHC, 70M and 10MHC only.12 Optional tri-volt electronic ballast capable of operating on any line voltage
from 200V-277V.13 Available with induction only.14 Not available with multi-tap or multi-volt ballasts.15 Available with electronic, HID only.16 Lamp included.17 Not available with KiloWatch.18 Lamp wattage not to exceed ballast wattage.19 For specific ordering information, see KiloWatch brochure, form no. 720.146
or consult factory.20 Not available with HS (house-side glare shield) or 200M.
Ordering Information Example: PGr 175M tB lPi
system. 50 watt - 70 watt metal halide with elec-tronic ballast - ballast is high power factor, <15% THD with starting temperature of -22°F (-30°C). Medium base, UL Listed 660W, 600V, 4K socket. Compact Fluorescent: ballast is Class P, electronic, high power factor, <10% THD with starting tem-perature of 0°F (-18°C). Sockets are high tempera-ture thermoplastic with integral retention clip. Induction: High Frequency Generator – Supplies high frequency power to the discharge vessel (lamp) to initiate and maintain a gas discharge for a rate 100,000 hours of life (optimized for ambient temperatures ranging from -40° to 20°c. Higher ambient temperatures may reduce lamp life.) Power Coupler – Induction coil transfers energy from the generator to the dis-charge vessel. Discharge Vessel – Glass bulb con-tains a mixture of low-pressure mercury vapor and inert buffer gas. The wall of the discharge vessel is coated with a fluorescent powder which produces light at 3000K color and 80+ CRI.
Listings
UL Listed (standard). CSA Certified or NOM Certi-fied (see Options). UL Listed for 25°C ambient op-eration and wet locations.US patent no. D402,075. Canadian patent 86779.
Intended Use
For parking garage applications.
Features
Upper housing – Rugged, die-cast aluminum with one-piece silicone gasketing. Standard finish is white corrosion-resistant polyester powder paint. Other architectural colors available.
Lower Assembly – Precision injection-molded, UV stabilized acrylic . Hinged and secured with four stainless steel screws. Polycarbonate available.
Mounting – Fully silicone-gasketed, galvanized steel plate. Surface mounts to recessed box or pendant mounts to industry standard J-boxes. The quick-mounting bracket doubles as a hanger for the fixture allowing for trouble-free electrical connections. The fixture twist-locks into place in a firm, secure fashion.
Electrical – HID: All HPS lamps as well as 100M and 150M lamps are high reactance autotransformer, high power factor. 175M lamp is a constant-watt-age autotransformer. 200M lamp requires a Super CWA pulse start ballast. Ballasts are copper wound and 100% factory tested. 180°C Class H insulation
Garage Lighting, Surface-Mount
PGR
Dimensions are shown in inches (centimeters) unless otherwise noted. Height: 11-1/2 (29.2) Max. diameter: 15 (38.1) Max. weight: 20 lbs (9 kg)
Accessories (Order separately)
RK1 T20BIT Hex base driver bit, Torx® TX20, for tamper-resistant screws with center reject pin
RK1 T20DRV Torx® TX20 screwdriver for use with tamper-resistant screws with center reject pin
Designation
PGR
Wattage
High pressure sodium70S
100S150S
Metal halide70M
100M150M1
175M1
200M2
Electronic metal halide3
50M70M
50MHC70MHC
Compact fluorescent2/42TRT2/57TRT2/70TRT
Induction lighting85IL4
Voltage
1202085,6
2405,6
2776
3476
4806,7,8
TB6,8,9
MVOLT6,10,11
TVOLT12,13
Options/accessories
Installed LPI Lamp included6
LP Lamp factory installed L/LP Less lamp6
HS House-side glare shield6
HSR House-side glare shield ready6
FLR Frosted lower lens DN Downlight focused, (n/a HA or HS)6,8
CSA CSA Certified NOM NOM Certified, consult factoryShipped separately OJB Offset junction box YK Yoke mount BDS Bird deterrent shroud (for use with non-surface mounting