VS1SD Analog I/O Jumper Settings Control Circuit Board Relay outputs Type Function Internal supply Active high JP6 JP1 J1 J2 J3 P3 JP3 JP3 JP2 ENP ENP EPN EPN EPN EPN EPN DFT DFT DFT DFT DFT INP INP INP INP INP ENP ENP ENP JP6 120 ohm termination No termination JP5 JP5 JP5 JP5 JP5 JP6 JP6 JP6 Factory settings as shown Note: Relay outputs are rated at 10-30 VDC or 240 VAC @ 5 A resistive (non-inductive). Digital input connections shown when using factory default jumper settings 1 1 1 1 2 3 45 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Load Load Load P1503 P1504 Load Relay Out 1 N.C. Enable 0-10 VDC Dig. Input 1 Analog GND Analog input 1 Pot. reference Analog input +2 Analog output 1* Analog output 2* *Referenced to J1-1 Analog input -2 P1408 P1510, P1511, P1512 P1513, P1514, P1515 Dig. Input 2 Dig. Input 3 Dig. Input 4 Dig. Input 5 Dig. Input 6 Dig. Input 7 Dig. Input 8 Relay Out 1 COM Relay Out 2 COM Relay Out 1 N.O. Relay Out 2 N.O. Relay Out 1 N.C. 232425 26 27 28 29 30 P1 Fault USB USB port 1 1 1 1 RS485 S G A B S 1 1 Active low External supply ANAIN2 JP1 ANAOUT1 JP2 Voltage Current Communications Termination jumper Digital Outputs Control Board Control Board Sourcing Current Connections Sinking Current Connections Note: Digital outputs are rated at 24 VDC @ 60 mA resistive (non-inductive). J2 J2 P1501 Out 1 P1501 Out 1 P1502 Out 2 P1502 Out 2 J3 J3 Digital output 1+ (Collector) Digital output 1+ (Collector) Digital output 2+ (Collector) Digital output 2+ (Collector) Digital output 1- (Emitter) Digital output 1- (Emitter) Digital output 2- (Emitter) Digital output 2- (Emitter) External User Return External User Return External User +24 V External User +24 V Internal +24 V Internal +24 V Internal 24 V Return Internal 24 V Return 17 17 18 18 19 19 20 20 21 21 22 22 23 23 24 24 Note: Optional equipment such as input/output reactors/filters are not shown. See instruction manual MN766. Note: See instruction manual MN766 for important information regarding motor power wiring and output reactors. Thermostat and control leads must be in separate conduits. Frame Size AA 1-Phase Input Drives Frame Size AA 3-Phase Input Drives Frame Size B and C Drives Frame Size D Drives L1 L2 N GND R1/B+ R2 B- T1 T2 T3 TH1 TH2 GND L1 L2 L3 GND R1/B+ R2 B- T1 T2 T3 TH1 TH2 GND L1 L2 L3 B+/R1 R2 B- T1 T2 T3 TH1 TH2 GND L1 L2 L3 T1 T2 T3 R+/R1 R2 B- Motor Chassis Ground Motor Chassis Ground TH1 TH2 GND Keypad Components The keypad is used to program the control parameters, to operate the motor and to monitor the status and outputs of the control by accessing the display options, the diagnostic menus and the fault log. Additionally, drive parameters can be stored in the keypad for future retrieval. Display Features Speed Reference Defines action of F2 key Defines action of F1 key Local Remote Present Menu Selection Stop – Forward – Reverse Indicator Lights: (On when indicated Key is active) FWD & REV: Green light indicator. STOP: Red light indicator JOG: Jog Speed Selected Green light indicator Display Diagnostics – I/O Status I/O Function configuration Modified Parameters Control Operation Data Custom Units Fault Display – 10 Faults with Time Stamp F2 – Clears faults or undo parameter edit changes or function indicated by text displayed directly above key. Up Arrow Left Arrow Down Arrow Right Arrow Moves cursor to select menu choices. LOCAL/REMOTE – Switches between local and remote modes. HELP – Provides help at each display screen, setup parameter and fault. Press to view/close help information. JOG – Initiates Jog mode. Press FWD or REV for motion. Only in local mode. FWD – When pressed, initiates a forward direction run command. Indicator Lights – (on indicated key) STOP key with red light indicator. FWD key with green light indicator. REV key with green light indicator. JOG key with green light indicator. Keypad Display – Displays status Information during Local or Remote operation. It also displays information during parameter setup and fault or Diagnostic information. F1 – Alternates or "toggles" between the last two menu choices or function indicated by text displayed directly above key. ENTER – Press ENTER to save parameter value changes. In the display mode the ENTER key is used to directly set the local speed reference. It is also used to select other operations when prompted by the keypad display. MENU/ESC – Selects the menu display when viewing status. The following menu items are shown: Status, Basic Params, Advanced Prog, Event Log, Diagnostics and Display Options. Backs up one level for other screens. REV – When pressed, initiates a reverse direction run command. STOP – Initates a stop command. Note: Pressing the stop key twice in succession will immediately disable the top drive placing the motor in a coast stop condition. STATUS FWD LOCAL 159.5V 600RPM 6.2A 20.0HZ DIAG 600R MAIN Digital Input Jumper Settings Please consult the VS1SD Installation and Operation Manual, MN766, before operating the drive. Also, please read the precautionary and warning statements in the Safety Notice, Paragraph 1.2, in MN766. AC Input power PE Star Point See instruction manual MN766 Fuses AC Input Dynamic Brake SHIELD