Volume V: Duraplus ® Air-Line System Industrial Technical Manual Series DURAPLUS ® AIR-LINE SYSTEM A lightweight corrosion resistant compressed air distribution system from IPEX SECOND EDITION
Volume V:Duraplus®
Air-Line System
Industrial TechnicalManual Series
DURAPLUS ® AIR-LINE SYSTEM
A l ightweight corros ion res istantcompressed a ir d istr ibut ion systemfrom IPEX
S E C O N D E D I T I O N
IPEX Duraplus® Air-Line
Industrial Technical Manual Series Vol. V. 2nd Edition
© 2007 by IPEX. All rights reserved.No part of this book may be used or reproduced in any manner whatsoeverwithout prior written permission. For information contact: IPEX, Marketing,2441 Royal Windsor Drive, Mississauga, Ontario, Canada, L5J 4C7.
LITERATURE & WEBSITE DISCLAIMER
The information contained here within is based on current information and product designat the time of publication and is subject to change without notification. IPEX does notguarantee or warranty the accuracy, suitability for particular applications, or results to beobtained therefrom.
About IPEXAt IPEX, we have been manufacturing non-metallic pipe and fittings since 1951. We formulate most of our compoundsourselves, and maintain strict quality control during production. Our products are made available for customers thanks to anetwork of regional stocking locations throughout North America. We offer a wide variety of systems including complete linesof piping, fittings, valves and custom-fabricated items.
More importantly, we are committed to meeting our customers’ needs. As a leader in the plastic piping industry, IPEXcontinually develops new products, modernizes manufacturing facilities and acquires innovative process technology. Inaddition, our staff take pride in their work, making available to customers their extensive thermoplastic knowledge and fieldexperience. For specific details about any IPEX product, contact our customer service department (contact information islisted on the back cover).
SAFETY ALERTS
Duraplus Air-Line must be used downstream from thereceiver or aftercooler only.
Care must be taken to avoid overheating Air-Line. Metalpipe must be used between compressor and receiverand at any other part of a system where conditionsexceed those permissible for Air-Line.
Air-Line should not be connected directly to vibratingmachinery. Flexible couplings should be incorporated toabsorb vibrations.
Duraplus Air-Line pipe must not be threaded.
Lubricators must only be installed at the downstreamextremities of the system.
Air-Line must not be bent. Standard elbows and moldedbends are available throughout the size range.
Certain types of flexible hoses contain plasticizers whichare harmful to Air-Line piping. Therefore the suitabilityof hoses which are to be installed upstream of theAir-Line system must be checked with IPEX prior toinstallation.
Purge new compressors and ancillary equipment,including new steel piping, prior to connecting to the Air-Line system.
After installation, the Air-Line system must be inspectedfor external damage in the form of cuts or deep notches.Any such damaged areas must be cut out and replaced.
The normal precautions for testing a compressed airsystem before pressurizing must be followed for the Air-Line system.
Anaerobic thread sealants (e.g. Loctite, 542, 572) canchemically attack Air-Line and must not be used.
Air-Line is ideally suited to clean air applications.Where air is not free from oil, IPEX must be consulted priorto installation concerning the suitability of the compressoroils to be used.
Note that synthetic oils are generally not compatiblewith Air-Line and must not be used with the system.Certain additive rich mineral oils are also incompatiblewith the system.
As a safeguard, IPEX has produced oil warning labels forattachment to the compressor. These are available uponrequest. A reduced copy of the label is shown below.
IPEX cannot accept responsibility for accidents arisingfrom the misuse of their products because of incorrectdesign, installation or application.
Unless the procedures and recommendations set out inthis manual have been strictly adhered to, all warrantiesare null and void.
W A R N I N GCertain compressor and lubricating oils will damageyour Duraplus Air-Line installation
Before using any oils in the system, contact IPEXto obtain a list of recommended oils or to confirmindividual oil suitability.
CDN (866) 473-9462 U.S. (800) 463-9572
AREAS OF USE INSPECTION AND TESTING
INSTALLATION PRECAUTIONS WARNING
Care should be taken to avoid prolonged exposure tosunlight, which will cause discolouration of the Air-LineXtra material. If stored outdoors, products must beunderneath an opaque covering, e.g. a tarpaulin.
If installed in a location exposed to sunlight, thepipework should be painted.
U.V. LIGHT
COMPRESSOR OILS
This page intentionally
left blank.
iDuraplus® Air-Line System
CONTENTS
Section Two: General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features & Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Section Two: Material Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3The Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
The System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Joining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Operational Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mode of Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Compressor Oil Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Section Three: Design Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Design Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Pressure Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Contaminants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
General Considerations for Piping System Design . . . . . . . . . . . . . . . . . . . . . . 7
Pipe SizingPipe Sizing – Main Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pipe Sizing – Branch Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Pressure Drops in Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Section Four: Handling and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Storage On-Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Z-Length Installation Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installation Techniquies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Installation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pipe Supports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Support Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Joining Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
BSPT & NPT Pipe Thread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Quick-Release Coupling Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Thermal Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Pipe Flexibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Joining Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Handling and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Duraplus® Air-Line Systemii
Section Five: Dimensions Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Section Six: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Sample Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Section Seven: Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Only the correct Duraplus cement will provide a compatible joint. All warranties void if other cement used. 1
OverviewCompressed air, a major source of industrial energy, is being used increasingly in both the manufacturing and processingindustries. There, its distinct advantages of cleanliness, flexibility, safety and economy of use (compared with other energysources) are fully exploited.
Modern process equipment, pneumatic controls and instrumentation demand a supply of clean, uncontaminatedair and this has prompted the development in recent years of more advanced designs of compressors and ancillary equipment.
Duraplus Air-Line is manufactured from a specially formulated Acrylonitrile Butadiene Styrene (ABS) blend that has a highperformance co-extruded nylon liner which greatly enhances its mechanical and chemical properties. Duraplus fittings aremanufactured using an alloy blend of ABS and nylon, ensuring high performance of the whole system.
Features and Benefits
Safety
The Butadiene component of Duraplus Air-Line contributesresistance to accidental damage and prevents materialfracture should the pipe be subjected to severe impact.Duraplus has been designed and tested to withstand impactfor a large range of temperatures and has a design life of30 years with a factor of safety of 2:1.
Wide Range of Applications
The advanced liner and ABS material combination protectsagainst stray chemicals which may sometimes causeproblems for ordinary systems. Duraplus Air-Line is nowcompatible with even more compressor lubricants.
Low Installation Costs
Duraplus Air-Line pipe reduces costs on a typical installationnot only for materials but also for labor and transportationcosts when compared to traditional materials. The reason?Its lightweight construction and simple assembly procedures.Like all thermoplastics, Duraplus is easly handled, stored,cut,joined and installed. As a result, project costs for installedDuraplus systems are significantly lower. Requirements forheavy installation equipment are also eliminated.
Clean
Duraplus products are packaged to protect the surface finishof the pipe and fittings and to prevent contamination beforeuse. The smooth liner of Duraplus Air-Line cannot rust,corrode or form loose scale, ensuring air remains cleanthroughout the life of the system.
Smooth Interior
Less friction means lower pressure drops and higher flowrates allowing for smaller pipe diameters to be used insome cases.
Ease of Use
Duraplus Air-Line is one sixth the weight of steel and can bejoined by solvent welding for easy on-site modifications andrepairs without requiring special training or equipment.
Leak Free System
Correctly made solvent welded joints are leak free and cangreatly reduce running costs.
Metric Sized & Colour Coded
Duraplus Air-Line is metric sized to prevent mixing with I.P.S.sized PVC and CPVC pipe. Also the Duraplus Airline is colourcoded blue to comply with the ISO standards for compressedair products.
Proven
From manufacturing to the marketplace, Durplus Air-Line issupported by the technical experience gained through over30 years of thermoplastic pressure piping production. Bothraw material and finished Air-Line products are subjected torigorous tests, including aging, weathering and stressedenvironmental tests, to ensure complete system integrity overthe designed operating life.
This manual serves to outline the design and installationtechniques required to achieve a safe, high-integrity system.Further detailed advice can be obtained from our CustomerService Department.
GENERAL
INFORM
ATION
GENERAL INFORMATION
1Duraplus® Air-Line System
GEN
ERAL
INFO
RMAT
ION
Duraplus® Air-Line System2
2
Applications
• Plant Air
• Food and beverage – CO2 delivery
• Ventilation
• Valve actuation
MATERIAL
DESCRIPTION
The MaterialAcrylonitrile-Butadiene-Styrene (ABS) is a broad family ofengineered thermoplastics with a range of performancecharacteristics.
The copolymeric system can be blended to yield the optimumbalance of properties suited to compressed air applications.Acrylonitrile imparts chemical resistance and rigidity.Butadiene endows the product with impact strength andtoughness, while Styrene contributes to ease of processing.
The formulation used by IPEX for Air-Line has been selectedto optimize performance in respect of tensile strength,toughness, ductility, heat stability and processability – fromraw material to finished product. These properties make itparticularly suitable for conveying compressed air.
In addition, the material has good chemical resistance and iseasily joined by solvent welding, which allows fast systemassembly and modification.
The SystemAdvanced manufacturing techniques allow the formation of aliner layer to be permanently fused with the ABS layer duringthe extrusion process. The nylon liner is a high performancecopolymeric material which offers extra strength andan unrivalled level of chemical resistance.
Fittings are produced in an alloy blend of ABS and the linermaterial, which has been carefully balanced to achieve aperformance improvement equivalent to the new pipe.
Duraplus Air-Line offers resistance to stray aggressivesubstances which may contaminate compressed air pipelinesand cause problems for other thermoplastic materials.Though Duraplus Air-Line is resistant to a large variety ofstray aggressive substances it may suffer stress attack ifexposed to some compressor oils.
JoiningAll socket fittings are joined by solvent welding usingDuraplus Air-Line cement. This cement has been specificallyformulated for maximum joint efficiency, therefore no othercement should be used.
In addition to socket fittings, threaded adapter fittings areavailable in the smaller sizes for connecting to filters,regulators, lubricators, quick release couplings and otherterminal connections or equipment. IPEX recommends theuse of Teflon tape for making threaded connections. Pastesmay cause stress cracking of the threaded joint.
Air-Line pipe must never be threaded.
Both pipe and fittings are manufactured from a copolymericpressure piping material – acrylonitrile butadiene styrene(ABS). They are capable of withstanding a continuousworking pressure of 185 psi at 73ºF (1275 KPa at 23ºC)in accordance with ASTM D2282.
The outside diameters of the pipe comply with thedimensional requirements of DIN 8062, and ISO 161/1.The socket sizes of the fittings conform with the dimensionalrequirements of DIN 8063 and ISO 727.
The sockets of the fittings have a 0º 30’ taper, the diameterdecreasing from the opening to the stop.
The table below shows the socket dimensions in inchesfor the whole range of fittings.
OD = Nominal Pipe outside diameter
A = Minimum socket depth
B = Socket diameter at mid-point of socket depth
AgeingResistance
Heat Resistance
Chemical Resistance
LowTemperature
Property Retention
Impact Strength
Lustre
Moldability
Strength
ABS
MATERIAL DESCRIPTION
3Duraplus® Air-Line System
OD A B Min B Max
(mm) (in) (mm) (in) (mm) (in) (mm) (in)
20 1/2 16.002 0.630 20.091 0.791 20.295 0.799
25 3/4 18.491 0.728 25.095 0.988 25.298 0.996
32 1 21.996 0.866 32.016 1.264 32.309 1.272
50 1-1/2 31.013 1.221 50.089 1.972 50.292 1.98
63 2 37.490 1.476 63.094 2.484 63.297 2.492
90 3 51.003 2.008 90.094 3.547 90.297 3.555
110 4 61.011 2.402 110.109 4.335 110.312 4.343
MAT
ERIA
LDE
SCRI
PTIO
N
Duraplus® Air-Line System4
Localized ductile failure of Duraplus Air-Line pipe sample inforeground, compared with explosive, failure of PVC pipe. (Bothsamples charged to 80 psi (552 KPa) with compressed air.)
MATERIAL DESCRIPTION
Operational RangeThe Air-Line system is designed for a maximum continuousservice pressure of 185 psi at 73ºF (1275 KPa at 23ºC).
Any increase in working temperature above 73ºF (23ºC) willrequire a corresponding reduction in pressure rating asdetailed on page 6. For example, at 120ºF (49ºC), the systemis derated to 115 psi (793 KPa).
Mode of FailureDuraplus Air-Line is made from a ductile material whosemode of failure resembles that of soft copper. Failure is byductile distortion and tearing.
In contrast, the failure of rigid materials, (PVC, CPVC, etc.)is accompanied by rapid crack propagation and hazardousmaterial fragmentation. The resulting explosion whenconveying compressed air can be catastrophic and couldcause injury. Unplasticised, rigid plastic piping must never beused for compressed gas conveyance.
Compressor Oil SelectionAir-Line is ideally suited to clean air applications and insystems, required to be free of oil.
Where compressors are selected that are not of the ‘oil free’design, varying amounts of compressor lubricant will bedischarged from the compressor into the downstream pipingand equipment. The amount of oil discharged in the systemwill depend on the type, manufacture and age of thecompressor selected.
Compressors can normally operate with either synthetic ormineral oil lubrication. Synthetic oils can damage seals,polycarbonate lubricator bowls and other elastomericcomponents and care should be taken in their selection.Air-Line can be similarly affected.
It should be carefully noted that synthetic oils, except for aselect few, are incompatible with Air-Line and must not beused with the system – otherwise permanent damage willresult. Certain additive rich mineral oils are also incompatiblewith the system.
Compressor oils should therefore always be checkedwith IPEX for compatibility with Air-Line beforebeginning installation.
Make certain that proper cleaning procedures are followedif the compressor lubricant needs to be changed. It isessential that the Duraplus cleaning guidelines are followed.Please contact IPEX for details.
Standard pipe impact test showing Air-Line ductility.
DESIGN DATA
DESIGN DATA
5Duraplus® Air-Line System
Design Considerations
Size Range
IPEX offers a comprehensive range of pressure pipingand matched precision molded fittings in the followingmetric sizes:
This equates to an equivalent range of 1/2" to 4" nominaldiameter (see below size comparison table). For pipe sizesabove 4" NPS (110 mm), contact IPEX technical services.
Product Range Dimensions
The table below shows the nearest equivalent IPS sizes ofgalvanized mild steel piping, plus weight comparisons.
Note: Metric/Imperial conversion charts are locatedin Appendix A.
Galvanized Mild Steel, Sch 40
(mm)
20
25
32
50
63
90
110
lbs/ft
0.090
0.120
0.190
0.460
0.730
1.500
2.210
in
1/2
3/4
1
1 1/2
2
3
4
in
0.840
1.050
1.315
1.900
2.375
3.500
4.500
in
0.622
0.824
1.049
1.610
2.067
3.068
4.026
lbs/ft
0.980
1.280
2.000
2.960
4.150
6.790
9.680
Air-Line 185 psi (1275 KPa)
Nominal OD Weight
(mm)
15.0
20.0
25.0
40.0
50.0
80.0
100.0
in
0.590
0.790
0.980
1.580
1.970
3.150
3.940
in
0.790
0.990
1.260
1.970
2.480
3.550
4.340
(mm)
20.0
25.0
32.0
50.0
63.0
90.0
110.0
ID
(kg/m)
0.130
0.180
0.280
0.690
1.090
2.230
3.310
(mm)
21.3
26.7
33.4
48.3
60.3
88.9
114.3
OD WeightID
(mm)
15.8
20.9
26.6
40.9
52.5
77.9
102.3
(kg/m)
1.450
1.900
2.970
4.430
6.170
10.100
14.400
mm 20 25 32 50 63 90 110
inch 1/2 3/4 1 1/2 2 2 1/4 3 4
DESI
GN D
ATA
DESIGN DATA
Duraplus® Air-Line System6
Pressure RatingsDuraplus Air-Line is designed for a maximum continuous workingpressure of 185 psi at 73ºF (1275 KPa @ 23ºC)for 30 years.
This pressure must not be continuously exceeded or areduced service life will result.
TRANSIENT increases in pressure can be tolerated up to amaximum of 10% over the maximum continuous pressure ata given temperature.
For increased compressed air temperatures, the pressurerating of Air-Line should be correspondingly reduced, asindicated on the graph. For example, at 120ºF (49º) thesystem can be operated continuously up to 115 psi(793 KPa) internal pressure.
When the system’s pressure/temperature combination is toohigh for the Air-Line system, the air temperature must bereduced by employing aftercoolers or other methods.Alternatively 230 psi (1586 KPa) rated Duraplus Industrialpiping may be suitable – contact IPEX’s Customer ServiceDepartment for advice.
NOTES:
1. Graph is based on an ambient temperatureof 73ºF (23ºC).
2. For higher ambient temperatures, decrease the workingpressure by 5% for every 20ºF (11ºC) above 73ºF (23ºC)ambient.
3. Generally compressed air systems must not be used attemperatures below 40ºF (4ºC) or in excess of 120ºF(49ºC). For applications outside these parameters consultIPEX’s Customer Service Department.
200
180
160
140
120
100
80
60
40
20
40 50 60 70 80 90 100 110 120
Air-Line - 185 psi
Compressed Air Temperature oF (oC)
Pressure/Temperature Ratings
Wo
rkin
g P
ress
ure
psi
(K
Pa)
(1379)
(1241)
(1103)
(965)
(827)
(690)
(552)
(414)
(276)
(138)
(4) (10) (16) (21) (26) (32) (38) (43) (49)
DESIGN DATA
Overview of Design
1. Locate each process, work station, or piece of equipmentthat uses compressed air. They should be located on aplan, and a complete list should be made to simplifyrecord keeping. This initial process will act as abeginning for your piping layout.
2. Determine the volume of air and pressure range used ateach location. Information regarding pressure and flowrates for equipment such as tools can be obtained fromthe manufacturer. If the pressure and flow rates are notknown, assign some preliminary rates until the specificvalues can be obtained.
3. Determine the system conditioning requirements for eachpiece of equipment. This includes the allowable moisturecontent, particulate size, and oil content. The system mayrequire conditioning equipment including dryers, filters,lubricators and pressure regulators.
4. Establish how much time the individual tool or processwill be in actual use for a one-minute period of time.This is referred to as the “duty cycle.” In most industrialapplications, tools or operations of a similar nature areusually grouped together.
5. Establish the maximum number of locations that may beused simultaneously on each branch, on each main, andfor the project as a whole. This is known as the “usefactor.”
6. Establish the extent of allowable leakage. Leakage is aresult of the number and type of connections, the use ofdisconnects, the age of the system and the quality of theinitial assembly process. Many small tools and operationswill result in more leakage than fewer larger applications.A well maintained compressed air system will have anallowable leakage rate of 2% to 5%.
Note: This allowable leakage rate applies only tocompressed air made on site. All other inert gas systemsmust be designed with the strictest health and safetyconsiderations in mind including preventing leakage ofany pipe contents.
7. Establish any allowance for future expansion. Thoughtshould be given to oversizing some components(i.e., main supply lines) to avoid the cost of replacementat a later date.
8. Make a preliminary piping layout and assign a preliminarypressure drop for the system.
9. Select the air compressor type, conditioning equipment,equipment location, and air inlet, making sure that scfm(L/min) is used consistently for both the system andcompressor capacity rating.
To start, the following information must be available:
• Total connected flow rate cfm (L/min) of allair-using devices, including flow to the air dryer systemif applicable.
• Maximum pressure (psi) all air-using devices require.
• Duty cycle and use factors for these devices givingmaximum expected use of air.
• Leakage and future expansion allowance, cfm (L/min).
• Allowable pressure drops for the entire system, includingpiping and conditioning equipment.
• Altitude, temperature, and contaminant removalcorrections.
• Location where adequate space is available for aircompressor and all ancillary equipment.
• Produce a final piping layout and size the piping network.
ContaminantsAn understanding of the various pollutants in the air ishelpful when an engineer has to decide what equipment isrequired to effectively reduce or remove them. The requiredlevel of protection from the various contaminants dependsupon the purpose for the air. Prior to the selection ofequipment, the performance criteria for each system, alongwith the identity and quantity of pollutants, must bedetermined.
There are four general classes of contamination:
1. Liquids (oil and water)
2. Vapor (oil, water, and hydrocarbons)
3. Gas
4. Particulates
General Considerations for Piping System DesignA compressed air system must be controlled, regulated, and sized to ensure that an adequate volume of air, at a specificpressure and purity, will satisfy user requirements during the period of heaviest use.
7Duraplus® Air-Line System
DESI
GN D
ATA
Duraplus® Air-Line System8
PIPE SIZING – MAIN LINES
The compressed air mains are the all-important link betweenthe compressor and the point of use. Correct sizing of thepiping system for both current and future demand isessential to maximize the cost-effectiveness of the system.Piping pressure drops are totally unrecoverable, a completewaste of energy and should be kept to an absolute minimum.
Mains that are too small will also cause high air velocity,making it difficult to separate the water from the air (sincemuch of the condensed vapor running as water along thebottom of the pipe will be whipped up by, and carried alongwith, the fast moving airstream).
For the main distribution line from the compressor, excessivepressure drops and energy loss can be avoided by restrictingair velocity to a maximum of 1,200 scfm. Higher velocities,can be permitted in the shorter service lines. Oversizing willresult in increased initial capital expenditure but is notadverse in any other respect. The larger pipe is in factadvantageous, acting as a reservoir or receiver for the air thusreducing the load on the compressor and providing capacityfor increased future demand.
In order to determine the correct pipe size for a particularlength of main, the following information is required:
a. Total length of pipe, L (ft.)b. Volumetric flow rate of air, Q (cfm)c. Pressure output of compressor, P (psi)d. Allowable pressure drop in the system, P (psi)
The total system pressure drop should not exceed 4 psi andideally 1.5 psi. However, a drop slightly in excess of this canusually be tolerated.
Air-Line GraphA graph has been designed for pipe sizing and pressure dropcalculation. It is based on the Standard IsothermalCompressible flow formula. (Isothermal process taken placeunder constant temperature.)
The graph is not intended to give absolutely preciseinformation. However, it does provide an acceptable means ofdetermining pipe sizes which are sufficiently accurate for themajority of industrial systems.
A worked example is shown with the values plotted on thegraph to illustrate its correct use.
How to use the NomogramExample:What size of pipe will be required for a system 920 ft. long,comprising fittings with a pressure drop, equivalent to a 64 ft. length of pipe. Charts for pressure drops due to fittingscan be found on page 7.
The compressed air is required to drive air tools andequipment with a total air consumption of 424 scfm. Theminimum pressure required to drive the tools and equipmentis 102 psi. A compressor rated at 116 psi and 530 scfm hasbeen chosen to allow for increased future demand.
The piping should be sized for the anticipated futuredemand.
Solution:
L = 920 + 64 = 984 ft.Q = 530 scfmP = 116 psi
Pressure drop is chosen to be = 1.5 psi
The length of the pipe run is plotted on scale ‘A’ and flowrate on ‘B’. A straight line is drawn to connect ‘A’ to ‘B’ andextended to ‘C’.
The compressor output pressure (116 psi) is now plotted onscale ‘E’ and the acceptable pressure drop (1.5 psi) isplotted on ‘G’. Again, a straight line is drawn to connect ‘E’to ‘G’ which cuts through ‘F’.
The intersection points on ‘C’ and ‘F’ are now connected witha straight line. The intersection of this line through scale ‘D’gives a minimum pipe size. In the example, the line ’C’ to ‘F’cuts ‘D’ at just under 90 mm. ‘D’ is scaled in standard pipesizes and therefore the minimum suitable pipe size will bethat shown immediately above the intersectioni.e. 90 mm (3").
33
6698
131164
328
656984
1640
3280
6560
16400
6350
4230
31802118
160012701060850635530425320212170127
85
64
42
21
11
5
2
110
90
75
63
50
32
25
20
16
12
15
29
43
58
87
116
145181
1.5
3
4.3
5.8
7.2
8.7
11.614.5
22
29
A B C D E F G
∇
SCFM = standard cubic feet/minute
DESIGN DATA
9Duraplus® Air-Line System
PIPE SIZING – BRANCH LINES
Higher velocities can be permitted in branch lines than inmain lines.
The flow data chart gives maximum recommended flow inscfm through Air-Line pipe at various applied pressures.This should be used as a guide only.
The chart is based on a pressure drop in a 100 ft. maximumlength of branch line using a 5% maximum pressure drop.E.g. a compressor delivering 80 psi and 50 scfm at 73ºFwould require a 3/4" (25 mm) pipe (actual maximumcapacity would be 59.74 scfm).
AppliedPressure
Pipe Size(in)
1/2
3/4
1
11/2
2
3
4
5 psi
1.55
2.86
5.97
18.50
34.07
84.33
160.00
10 psi
3.00
5.97
12.73
39.13
72.36
188.10
332.70
20 psi
7.20
12.84
27.38
81.55
151.40
395.80
684.30
40 psi
13.03
27.42
59.04
168.90
314.70
814.90
1435.00
60 psi
21.10
42.85
90.99
269.60
505.60
1259.00
2266.00
80 psi
30.71
59.74
123.10
374.60
706.20
1732.00
3077.00
100 psi
42.76
77.32
156.00
481.60
911.50
2196.00
3914.00
150 psi
59.00
118.90
237.20
744.80
1416.00
3353.00
5984.00
Maximum recommended air flow (scfm) (standard cubic feet/minute)
Pressure Drops in FittingsPressure drops occur in pipe, and also across fittings, valves, filters, etc. Therefore, total pressure drop is the summation ofall the individual pressure drops for valves, filters and other ancillary equipment.
For pressure drops across filters and other equipment, refer to the particular manufacturer’s literature.
90º elbow
45º elbow
90º bend
Tee-in line flow
Tee-in line to branch flow
Reducer
Composite unions
180O dropper bend
1/2 (20mm)
4.13
2.95
2.00
1.25
6.40
4.66
1.54
1.28
3/4 (25mm)
4.00
2.23
1.94
0.85
4.99
4.43
1.35
1.21
1 (32mm)
3.77
1.51
1.61
0.95
4.72
4.23
1.18
1.18
11/2 (50mm)
3.51
1.41
1.44
0.95
3.87
4.10
1.12
-
2 (63mm)
3.54
1.31
1.38
0.76
3.48
4.20
0.92
-
3 (90mm)
3.61
1.87
1.67
0.33
3.90
4.56
-
-
4 (110mm)
3.64
2.26
1.94
0.49
4.33
4.78
-
-
Pressure Drop in Fittings – Equivalent Pipe Length in Feet
Nominal Pipe outside diameter – in
NOTE: The table shows the length of pipe with equivalent pressure loss in a given size for a given fitting. For example, a 1.5in 90º elbow has a pressure loss equal to 3.51 ft of 1.5in pipe. All equivalent pipe lengthsshould be added to the total pipe length when calculating pressure drops in main and branch piping.
Fitting Type
Duraplus® Air-Line System10
This page intentionally
left blank.
HAN
DLING AN
DIN
STALLATION
Storage On-SiteThe high-impact strength of the Air-Line system providessome protection against the damage which occurs duringhandling and storage on site.
However, it is recommended that the following precautionsare taken:
1. The storage site should be flat, level and free from sharpstones, etc.
2. Pipe should not be stacked to heights exceeding thefollowing:
3. Smaller pipe may be ‘nested’ inside larger pipe.
4. Side bracing should be provided to prevent stackcollapse.
5. Pipe should not be subjected to excessive temperaturevariation within the stack.
6. Pipe should be protected from the direct sunlight usinga tarp or opaque sheet. If temperatures reach above100ºF, proper air flow should be allowed under the tarp.
Z-Length Installation MethodAs an aid to installation, Z-lengths have been added to thedimensional details of fittings shown in this catalog.The basic idea is to assist in prefabricating pipe sectionsand to avoid time-consuming and costly onsite work. By usingZ-lengths, as many measurements as possible are taken atone time and pipe sections can be preassembled away fromthe job site.
To fabricate pipe assemblies from sketches giving center-linedimensions, it is necessary to know the distance from theperpendicular center line of the fitting to the beginning ofthe pipe and in the case of sockets and similar fittings, thepipe stop length. These are the ‘Z-lengths’ (or “take-out”dimensions) and are the key to easy fabrication.
By subtracting the sum of the Z dimensions of the twofittings from the center-to-center measurement, the lengthof pipe required can be quickly determined. Thus thecutting length required (e) is obtained by subtracting thesum of the two lengths (Z1 + Z2) from the center-linemeasurement (L).
PIPE SIZE MAX. STACKING HEIGH
Up to 3" (90 mm) 20 x pipe size
4" (110 mm) & 6" (180 mm) 12 x pipe size
8" (220 mm) 7 x pipe size
10" 4 x pipe size
12" 4 x pipe size
e = L - (Z1 + Z2)
D
Z1 Z2
11Duraplus® Air-Line System
HAN
DLIN
G AN
DIN
STAL
LATI
ON
Duraplus® Air-Line System12
INSTALLATION TECHNIQUES
Installation MethodsAir-Line is more flexible and has a higher rate of thermalexpansion than metal pipe. It is important to follow theguidelines detailed in the following pages to accommodateexpansion and contraction and provide adequate support.
Flange Bolt Torque Values
Pipe Supports
Support Spacing
The following support spacing is recommended forAir-Line. For vertical pipes, the support spacing showncan be doubled.
Support Spacings for Air-Line Pipe
For each 20ºF rise in temperature, decrease these supportspacings by 10%.
Support DesignAir-Line is light in weight (approximately 1/8 the weight ofequivalent diameter steel). This means supports can be oflight construction.
When subjected to temperature changes, Air-Line will expandmore than metals. This expansion should be controlled bylaterally constraining the pipe while allowing free axialmovement.
Pipe supports should:
1. Be rigid in construction – to adequately support the pipe (fabricated mild steel angle is ideal).
2. Have a wide bearing area – to allow free transmission of pipe movement and to avoid localized stressing.
3. Be free from sharp burrs or edges – to avoid cutting into the pipe wall.
4. Allow free axial pipe movement – to avoid pipe snaking.
5. Provide lateral restraint – to avoid pipe snaking.
Any pipe clips used in conjunction with Air-Line should alsoallow free axial pipe movement and afford lateral restraint.IPEX Cobra snap-in pipe clips meet these requirements.A suitable alternative would be fabricated mild steel saddleclips, designed with a clearance between pipe and clip.
The diagrams illustrate the types of support ideally suited tothe Air-Line system.
Long hanger rod type supports are not designed to providelateral restraint to piping and are not recommended for usewith Air-Line where expansion is expected, since pipesnaking may result.
Outside Diameter Support Spacing at 73ºF (23ºC)
(in)1/23/41
11/223468
1012
(mm)
202532506390
110
***
*
(ft)
3.944.604.926.236.898.209.19
11.0012.5013.5014.50
(m)
1.21.41.51.92.12.52.83.43.84.14.4
The illustration shows 4" (110 mm) pipe.
*Note: For sizes above 4", contact IPEX technical support.
Pipe Diameter Torque Value
1" (32 mm) 13 ft.lb (18 Nm)
1 1/2 - 2" (40-63 mm) 22 ft.lb (30 Nm)
3" (75-90 mm) 30 ft.lb (40 Nm)
4" (110 mm) 33 ft.lb (45 Nm)
HAN
DLING AN
DIN
STALLATION
13Duraplus® Air-Line System
INSTALLATION TECHNIQUIES
Hanger rods may occasionally be used in conjunction withrigid supports where pipe spans are large and it is notpractical to support by any other method. In this case,hanger rods should be kept as short and rigid as possibleand must also allow free axial pipe movement.
Supporting Heavy Equipment
Large valves, filters and other equipment should always beindependently supported and anchored to prevent undueloading and stress being transmitted onto the Air-Linesystem.
For smaller valves and equipment, two pipe clips situatedimmediately adjacent to either side of the equipment willprevent transmission of excess torque and other loadings tothe Air-Line pipe.
Joining Methods
Solvent Welding
Joining Air-Line pipe and fittings is achieved by solventwelding. A detailed procedure is shown on pages 20 to 23.
Miscellaneous Joining
Threaded Connections – Air-Line to Metal
Air-Line pipe must not be threaded. Connections to metalthreads can be made using female threaded adapters orcomposite unions.
Thread lubricant such as Teflon® tape around the entirelength of threads, beginning with the number two thread fromthe end.
Anaerobic thread sealants, (e.g. Loctite, 542,572, Rectorseal #5)can chemically attack Air-Line and must not be used.
Connections should be tightened by hand, with a finalquarter turn with a strap wrench where necessary. Pipewrenches may induce overtightening with consequentialdamage to the fitting and therefore should not be used.
Air-Line should not be connected directly to vibratingmachinery. Flexible couplings should be incorporated toabsorb any movement.
BSPT and NPT Pipe Thread
Two main threads are used in the piping industry with bothcreating a hydraulic seal when tightened. This seal occursdue to the tapered design of the threads that causes thematerial to mesh when tightened. BSPT (British StandardPipe Thread Tapered) originates from Britain and is thestandard pipe thread used throughout most of the world.NPT (National Pipe Thread) originated in the US and hasbecome the standard pipe thread for North America.
BSPT thread uses the Whitworth thread form and has thefollowing characteristics:
• British standard 21 symmetrical V-thread in whichthe angle between the flanks is 55° (measured in anaxial plane)
• One-sixth of this sharp V is truncated at the top andthe bottom
• The threads are rounded equally at crests and roots bycircular arcs that blend tangentially with the flanks
The illustration shows 4" (110 mm) pipe.
BSPT
HAN
DLIN
G AN
DIN
STAL
LATI
ON
Duraplus® Air-Line System14
INSTALLATION TECHNIQUIES
NPT also known as ANSI/ASME B1.20.1 Pipe Threads hasthe following characteristics:
• ANSI/ASME standard B1.20.1 covers threads of 60°form with flat crests and roots
• Applicable sizes from 1/16-inch to 24-inch NominalPipe Size
• The taper angle for all NPT threads is 3/4 inches per foot.
The chart below shows the difference in threads per inchbetween NPT and BSPT. It can be seen that some sizes willhave the same amount of thread per inch for both types ofthread. This means that the parts will thread together.However, the difference in thread angle of 5° will causeinterference in the joint. This interference may cause thejoint to buckle before proper engagement occurs.
Threading a male NPT into a female BSPT is possible forcertain sizes because the threads per inch are the same orvery close. These similarities will allow the fitting to threadon partially before buckling or jamming together. Thisbuckling occurs before the joint is fully engaged and iscaused by the difference in thread angle between the twotypes of threads (see below). Though the joint will often workthere is an increased chance of a spiral leak occurring.
Nominal Size OD Threads per Inch1/2" 0.840" 143/4" 1.050" 141" 1.315" 11-1/2
1-1/2" 1.900" 11-1/22" 2.375" 11-1/23" 3.500" 84" 4.500" 8
NPT Standard External Thread
Nominal Size OD Threads per Inch1/2" 0.840 143/4" 1.060 141" 1.330 11
1-1/2" 1.900 112" 2.370 113" 3.500 114" 4.500 11
BSPT Female
NPT Male
Interference
Note: When threading thermoplastic materials it is alwaysrecommended to use Teflon tape as a lubricant and toachieve a leak free seal.
Connections to Instrumentation
Pressure gauges, temperature gauges and flow measurementprobes can be connected to the Air-Line system with femalethreaded adapters or composite unions solvent welded intoplain Air-Line tees. Alternatively, threaded saddle clamps canbe used.
BSP Tapered External Thread
NPT
HAN
DLING AN
DIN
STALLATION
15Duraplus® Air-Line System
INSTALLATION TECHNIQUIES
Quick-Release Coupling Connections
High Level
Quick release couplings or hoses may be connected to theAir-Line system by using a female threaded adapter orcomposite union, solvent welded to a dropper bend. Thismethod should be used in areas not normally accessible fromthe floor level and not subject to frequent disconnection.
The connection should be reinforced using two IPEX pipeclips as illustrated.
Termination of Drop Legs
It is important that the lower end of all pipe droppers andany take-off points, particularly those employing flexiblehoses, are rigidly attached to walls, pillars, etc. Two methodsare available for such terminations:
1. If drains are required, and the dropper is attached to atee, then the branch line will be held in place with a wallbracket.
2. When drains are not required, Air-Line wall brackets mustbe used at the lower end of the vertical droppers toprevent strain from flexible hoses.
Mechanical Joints
Systems which require frequent disassembly can use Air-Lineunions or stub flanges. (These can also be used at fixedterminal connections such as air receivers or dryers.)
Teflon® trademark of the E.I. DuPont Company.
HAN
DLIN
G AN
DIN
STAL
LATI
ON
Duraplus® Air-Line System16
INSTALLATION TECHNIQUIES
Thermal Expansion
Expansion Rates
While thermoplastics expand more than metals, they havea much lower thermal conductivity. This means the entirewall of a plastic pipe does not reach the same temperatureas the contents, unless the pipe is wholly immersed at thesame temperature inside and out.
The expansion and contraction of a plastic pipe is afunction of the change in average temperature of thepipe wall.
This means the expansion in a thermoplastic pipe isfrequently less than expected because the average pipewall temperature is lower than the contents.
Approximate expansion rates for Air-Line pipe are shownon the graph.
More precise information can be obtained from the formulagiven on page 18.
Controlling Pipe Expansion (Fig. 1)
Because of the small differences between ambient andservice air temperatures plus the low thermal conductivityof the Air-Line material, most pipe expansion can beaccommodated by using the inherent flexibility of theproduct and proper pipe supports and guides.
The basic principle of design is to allow pipe runs toexpand along their length from a fixed point and then toguide this expansion into a change of pipe direction whichwill flex as the pipe expands and contracts.
The following examples explain this principle infurther detail.
Pipe Constrained at Both Ends (Fig. 2)
In the diagram, the pipe run is fixed at one end to theflanged outlet of the air receiver, (Point A) and constrainedat the other end by virtue of its close proximity to the wall(Point B).
Problem (Fig. 2)
As the temperature increases, the pipe will try to expandoutward but will have nowhere to go because of its fixedends. The expansion will be directed inward from both thewall and the air receiver resulting in the pipe twistingbetween supports, as indicated.
Exp
ansi
on R
ate
(inc
hes/
feet
)
Expansion Rates for Duraplus Air-Line
Air receiver
APipe clip
B
Change in mid-wall temperature, ºF
Figure 1
Figure 2
HAN
DLING AN
DIN
STALLATION
17Duraplus® Air-Line System
INSTALLATION TECHNIQUIES
Solution (Fig. 3)
By using fabricated angle iron brackets and IPEX Cobra pipeclips along pipe length B, C, & D, the pipe can be installedaway from the wall with sufficient room for it to expand andcontract.
Now the pipe will expand away from its fixed point,(the air receiver – (A)), and the movement will be guidedinto the change of direction, i.e. pipe leg length B, C, D.
Note: The support at C remains, but the clip is removed togive it sufficient leg length for flexibility.
Pipe Anchors (Fig. 4)
In the previous example, the air receiver acted as an anchorpoint to the pipe system and this served to direct the thermalexpansion of the pipe – i.e. the pipe was forced to move inone direction from Point A.
Alternatively, an anchor can be placed at an appropriate pointin the run to control the direction of expansion.
Typical methods of producing anchors are shown inFigures 4a and 4b. The pipe should not be clamped,but simply restrained from moving.
Equipment such as valves, filters and lubricators needindependent support as previously indicated (page 13).These supports will automatically serve as anchors tothe system.
All the anchors previously described, provide complete axialand lateral pipe restraint. During installation, pipe clips maybe strategically positioned to serve as partial anchors.For instance, in Figure 5, a pipe clip has been positionedclose to Point B, forcing the expansion along pipe lengthBC and into leg length CD, which is able to flex.
NOTE: A saddle clip is used for this application.
Figure 3
Figure 5
Figure 4a Figure 4bFigure 4
HAN
DLIN
G AN
DIN
STAL
LATI
ON
Duraplus® Air-Line System18
INSTALLATION TECHNIQUIES
Pipe FlexibilityIt is essential that the pipe leg into which expansion isbeing directed is flexible enough to accommodate theexpected movement. In certain cases, pipe lengths mayneed to be increased or expansion loops may be required.
The methods shown in Figures 6-9 use flexibilityintroduced to accommodate expansion which occurs inthe direction of the arrows.
The pipe shown in Figure 9 has the required flexibilitybut expansion is constrained by clips fitted too close tothe bends. Movement can be controlled by anchoring andflexing the bends allowed for by moving the clips.
The degree of flexibility required in pipe legs dependsupon the amount of pipe expansion to be accommodated.Typical calculations are detailed below.
Flexibility – Sizing of Leg Lengths and Loops
The actual expansion, or contraction, ofAir-Line pipe is dependent on the change in temperatureof the mid-wall of the pipe. The mid-wall temperature isdependent on the internal and external temperatures withthe temperature of the compressed air having the greaterinfluence - unless the piping is subject to radiated heat.
The following simple equations may be used to calculateexpansion or contraction:
∆TL = Maximum temperature change of compressed air (ºF)
∆TA = Maximum temperature change of external air (ºF)
∆T = Change in average temperature of pipe wall (ºF)
∆L = Change in length of pipe (inches)
α = Coefficient of linear expansion of Duraplus Air-Line (in/inºF)
For Air-Line α = 5.6 x 10-5 (in/inºF).
L = Original length of pipe (feet)
To calculate pipe wall temperature change,use the equation
∆T = 0.65 ∆TL + 0.10 ∆TA
Using value of ∆T, calculate expansion.
∆L = ∆T x L x α
1/2" (20 mm)
3/4" (25 mm)
1" (32 mm)
1-1/2" (50 mm)
2" (63 mm)
3" (90 mm)
4" (110 mm)
6" (180 mm)
8" (220 mm)
20
1098765
4
3
2
10.90.80.70.6
0.5
0.4
0.3
0.2
0.11 2 3 4 5 6 7 8 910 20 30 40 50 60 70 8090100
∆L (
inch
es)
H (inches)
Air-Line - Expansion Loops
Figure 7Figure 6
axialrestraint
controlledexpansion
preferred
non-preferred
Key
SupportFlange
preferrednon-preferred
Figure 8 Figure 9
H/2 max
H
∆L ∆L
H
∆L
HAN
DLING AN
DIN
STALLATION
19Duraplus® Air-Line System
INSTALLATION TECHNIQUIES
Example 1: Leg Lengths
The 3" (90 mm) Air-Line pipe shown in Figure 10 isconveying compressed air at a temperature varying between100ºF and 120ºF. The ambient temperature varies from 60ºFto 90ºF. Determine the free leg length required at the changeof direction to accommodate thermal expansion.
Solution∆T = .65 (∆TL) + .1 (∆TA)
= .65 (120 - 100) + .1 (90 - 60)= .65 (20) + .1 (30)= 13 + 3
. . . ∆T = 16ºF
∆L = L α ∆T= (100 x 12) (5.6 x 10-5) (16)
. . . ∆L = 1.08 inches
Calculate leg length A-B
Using the value of 1.08", draw a horizontal line on the graph(page 18) from the vertical scale to meet the 3" (90 mm)pipe gradient line. Drop a perpendicular from the intersectionpoint to the horizontal scale. The figure obtained is the leglength required, i.e. length A to B.
In this case therefore, the leg length will be 56", i.e. the firstsupport guide should be positioned at B, 56" (1.42 m) fromthe elbow at A.
Note: A support without a guide may be required at point A.
Example 2 Expansion Loops
Determine the loop size required in a 2" (63 mm) Air-Linepipe which is constrained at both ends as shown in Figure11. the compressed air temperature varies between 100ºFand 120ºF. The ambient temperature varies from 40ºF to100ºF.
Solution:
The solution follows exactly the same principles used in theprevious example.
∆T = .65 (∆TL) + .1 (∆TA)= .65 (120 - 100) + .1 (100 - 40)= .65 (20) + .1 (60)= 13 + 6
. . . ∆T = 19ºF
∆L = L α ∆T= (100 x 12) (5.6 x 10-5) (19)
. . . ∆L = 1.28 inches
Calculate Loop Size
In this case, the expansion is equally split and directedinward from points A and B. Therefore, using a value of ∆L/2(i.e. 1.28/2=0.64"), draw a horizontal line on the graph fromthe vertical scale to meet the 2" (63 mm) pipe gradient line.Drop a perpendicular from the intersection point to thehorizontal scale. The figure obtained is the leg length of loopoffset required, i.e. 36" (.91 m)
?A
B
100 ft.
B = position of clip A
B
100 ft.
H
H/2
Figure 10 Figure 11
Fixed Point
Direction of Expansion
Pipe Movement
x
HAN
DLIN
G AN
DIN
STAL
LATI
ON
Duraplus® Air-Line System20
JOINING METHODS
Solvent Welding
Joining of Air-Line pipe and fittings is achieved by solventwelding. Correctly made, the resulting joints are strongerthan either pipe or fitting.
Air-Line solvent cement is designed and formulated to matchthe temperature and design performance of the Air-Linesystem. When applied, it will chemically soften the preparedsurfaces of the pipe and fitting, allowing fusion between themating surfaces when brought together.
The extent of softening by the solvent cement is dependentupon the removal of all traces of foreign matter from themating surfaces, i.e. oil, dirt, grease, etc. The cleaner themating surfaces, the stronger the resulting joint will be.
Joint Curing Times
The strength of the solvent cemented joint increases withcuring time. The initial cure is very rapid but full jointstrength is not reached for a number of hours. The actualcuring time depends upon a number of factors, including theamount of solvent applied, the fit of the component and theambient temperature. A guide to the amount of solvent to beused is shown below.
At a temperature of 73ºF (23º), an approximate curing timeis to allow one hour per 15 psi (103 KPa) of appliedpressure. However, a minimum of six hours must elapsebefore any system is pressurized.
Joints made in environments with higher ambienttemperatures will require longer curing times. For example,at 90ºF (32ºC), a full 24 hours should elapse before fullworking pressure is applied; at 100ºF (38ºC), 48 hours willbe required prior to pressurization.
Number of Joints per Quart
Under normal conditions, the following approximate numberof joints can be made per quart of solvent cement. Actualusage will depend upon ambient conditions and the fitbetween the pipe and fitting.
Joining Times
The following indicates expected times to produce solventjoints across the size range. These times may be extendedslightly under adverse installation conditions.
Solvent Cement Type
The integrity of the Air-Line systemwill be affected if the correctDuraplus Airline solvent cement isnot used. IPEX disclaimsresponsibility for any Air-Line systemconstructed with any other cementsor compounds or not fabricated inaccordance to the instructions contained herein.
Size (in)Number of
Approxmiate Joints1/2" – 1" 290
1-1/2" – 2" 144
3" 48
4" 32
6" 16
8" 10
10" 4
12" 4
Size (in) Joining Time
1/2" – 1" 5 mins/joint
1-1/2" – 2" 7 mins/joint
3" – 4" 10 mins/joint
6" 13 mins/joint
8" 16 mins/joint
10" – 12" 20 mins/joint
HAN
DLING AN
DIN
STALLATION
21Duraplus® Air-Line System
JOINING METHOD
Air-line Fittings Range
The use of reducer couplings, female threaded adapters andreducer bushings
All fittings have socket hubs, dimensionally controlled forsolvent welding. In addition, the illustrated fittings areprovided with inside and outside controlled diameters andcan therefore be used as spigot or socket components asshown.
Reducer Bushing
1" / 3/4" x 1/2" (32mm / 25mm x 20mm)Reducer Coupling
3/4" (25mm)Pipe
1/2" (20mm)Pipe
1/2" (20mm)Pipe
1" (32mm)Coupling
1" / 3/4" x 1/2"(32mm / 25mm x 20mm)
Reducer Coupling
PIPE TO PIPE
FITTING TO PIPE
PIPE TO FITTING
FITTING TO FITTING
2" / 1-1/2" x 2"(63mm / 50mm x 2in)
Adapter
1-1/2" (50mm)Pipe
2" (63mm)Coupling
2" (63mm)Pipe
2" / 1-1/2" x 2"(63mm / 50mm x 2in)
Adapter
Reducer Coupling
Female Adapter
Airline is metric sized. Equivalent inch sizes are:20 (1/2"), 25 (3/4"), 32 (1"), 50 (11/2"), 63 (2"), 90 (3"), 110 (4")
HAN
DLIN
G AN
DIN
STAL
LATI
ON
Duraplus® Air-Line System22 Duraplus® Air-Line System
JOINING METHODS
Procedure
Joining is simple and quick, but the following procedures must be adhered to if maximum joint efficiency is to be achieved.
1. Cut pipe clean and square. A hacksaw is convenient for smaller pipes but a fine-tooth carpenter’s saw hasproved to be more suitable on the larger sizes.
Proprietary rotary cutting tools specially designed for plastics can also be used, provided the cutting edges aremaintained in a sharp condition.
2. Cut a lead chamfer on the pipe with a file or chamfering tool.
This assists entry of pipe into fitting during joining and also prevents the solvent cement layer from beingsheared by the surface of the fitting when pushing the pipe fully home.
The size of chamfer will depend upon the pipe’s diameter but on average it will be 1/8" x 45º.
3. Remove internal and external burrs and clean out fittings.
Mark the pipe a convenient distance from the end to be joined – say 1" (25 mm) plus socket depth.
This enables checking the penetration of the pipe into the fitting after joining – the mark should be visible1" (25 mm) from the socket after joining. (This step will not be necessary as experience is gained since thefitter will be able to feel the pipe butt against the pipe stop.)
4. Lightly sand the end of the pipe over a length equal to the depth of the fitting socket, using only cleanmedium glass paper or emery cloth.
No attempt should be made to increase the clearance between pipes and fittings by heavy abrasion.
1 2
5. Lightly sand the socket of the fitting.
6. Thoroughly clean the sanded surfaces of pipe and fittings using a clean rag moistened withDuraplus MEK cleaner.
7. Open the can of Air-Line solvent cement and stir thoroughly. This ensures even distribution of the Air-Line resinwithin the solvent base and will aid the joining process.
3 4
5 6 7
HAN
DLING AN
DIN
STALLATION
23Duraplus® Air-Line System
8 9 10
11 12
18
JOINING METHODS
8. Using a clean brush or a roller, apply the solvent cement to the pipe and fitting.
One coat should be sufficient for all pipe sizes.
The cement should be applied quickly to both the pipe and fitting.
Care should be taken to avoid any excess deposit of solvent cement inside the fitting which could weaken thewall, particularly in the smaller sizes.
9. Immediately after applying the cement, push pipe fully home into the fitting.
Continue to exert the pressure necessary to hold the pipe into the fitting for times varying from five secondson 1/2" (20 mm) pipe to 20 seconds on 4" (110 mm) sizes. Otherwise, the slight taper of the Air-Line fittingsmay push the pipe out of the socket with loss of joint shear strength.
Check for full penetration of pipe to socket by measuring against the mark previously made on the pipe.
10. Wipe off excess solvent cement to avoid weakening the pipe wall due to continued solvent attack.
11. Replace lid on the solvent cement can to minimize solvent evaporation. This is particularly important in hot weather.
12. Clean brush with MEK cleaner and replace screw cap.
HAN
DLIN
G AN
DIN
STAL
LATI
ON
Duraplus® Air-Line System24 Duraplus® Air-Line System
Buried Pipe
Air-Line is equally suited to above ground and buried use.Recommendations covering essential requirements for largeruns below ground may be summarized as follows:
In general, trenches should not be less than 3' (.91 m) deep.However, site conditions may permit pipe being laid nearerthe surface – IPEX’s Customer Service Department should becontacted for detailed advice.
Trenches should be straight-sided and as narrow as possibleto allow proper consolidation of packing materials.
Trench bottoms should be as level as possible.
Large pieces of rock, debris and sharp objects should beremoved.
Unless the excavation is in ground of natural materials offine grains, a bed of finely graded pea gravel should be laid(3/8" (10 mm), or similar) approximately 3" (76 mm) deep onthe floor of trench. (Sand may be used but a high water tablemay wash sand away and leave the pipe unsupported.)
If piping is joined above ground, it should remainundisturbed for 2 hours before being ‘snaked’ into thetrench. Alternatively, the pipe may be joined in the trench.
Particular care should be taken to ensure piping and joiningmaterials are thoroughly dry and that the joining procedureshown in this manual was strictly followed.
Care should be taken to ensure that sharp objects, stones,etc., are prevented from falling into the trench. Backfillingshould be carried out between joints using pea gravel, orsimilar material, to a depth of 3" (76 mm) above the pipeand extended sideways to both trench walls. Joints should beleft exposed for pressure testing.
After pressure testing, joints should be covered with peagravel and backfilling completed.
Because of the condensation which can build up in anycompressed air system, drain pits should be constructed atthe lowest points of the line so a drain facility can beincorporated.
Air Testing Procedure
1. Fully inspect the installed piping for evidence of mechanical abuse and dry or suspect joints.
2. Split the system into convenient test sections not exceeding 1,000 ft (305 m).
3. Slowly pressurize each section to 15 psi (103 KPa) and allow the system to equalize for 30 minutes.
4. Check joints for leaks with a Duraplus-approved foaming agent. Never use leak detection sprays such as Snoop.If leaks are detected or the system loses pressure, stop the test immediately and relieve pressure.
5. Any threaded joints found to be leaking should bere-made using Teflon® (PTFE) tape wrapped around the thread. Any defective solvent weld joint should be cut out and replaced. Further tests should be suspended until the joint has fully cured for 24 hours.
6. After successfully pressurizing the system to 15 psi(103 KPa) for 30 minutes, gradually increase the pressure to 50 psi (345 KPa) and apply for 30 minutes. If any loss in pressure occurs, immediately suspend the test, release the pressure and correct the leaks as indicated above. Re-pressurize to a maximum of 15 psi ((103 KPa) and test each joint with a soap solution. Continue the test procedure as indicated above.
7. After successfully pressurizing to 50 psi (103 KPa) for 30 minutes gradually increase the pressure to full working pressure and apply for 1 hour.
If the system loses pressure, immediately suspend the testand release the pressure. Re-pressurize to a maximum 15 psi(103 KPa) and test each joint with soap solution. Continuethe testing procedure as indicated above.
Installed Exposure to Sunlight
All Air-Line piping installed outside and subject to exposureto sunlight must be painted for protection to retain the fulltoughness and ductility of the material. This can be achievedas follows:
1. Lightly abrade the pipe and fittings, using medium gradeglass paper, to provide a ‘key’ for the paint to adhere to.
2. Clean the system down with soap and water to remove any residual grease or oil. Do not use solvents or detergents.
3. Select a white, water-based latex paint, preferably one containing titanium dioxide. Do not use cellulose or solvent-based paints.
4. Apply an undercoat followed by a final gloss coat.
Teflon® trademark of the E.I. Dupont Company
HANDLING AND INSTALLATION
DIMEN
SIONAL DATA
25Duraplus® Air-Line System
Sized1 (in)
SignificantNumber
ProductCode
Critical Dimensions
Z1 A B Wt. (oz)
1/2 100306 437026 0.11 0.98 1.42 0.25
3/4 100307 437027 0.11 1.22 1.62 0.42
1 100308 437028 0.11 1.56 1.89 0.88
1-1/2 100310 437029 0.11 2.43 2.66 2.72
2 100311 437030 0.11 3.07 3.17 5.44
3 100313 437032 0.15 4.38 4.33 13.41
4 100314 437033 0.23 5.35 5.19 24.36
Duraplus Airline metric pipe and fittings are listed to the equivalent nominal Imperial size.
Pipe Size SignificantNumber
ProductCode
d1 t Min. Sch 40Wall Thickness(in) (mm) (mm) (in) (mm) (in)
20 1/2 553306 446000 20.0 0.79 2.9 0.114 0.109
25 3/4 553307 446001 25.0 0.99 3.0 0.118 0.113
32 1 553308 446002 32.0 1.26 3.6 0.141 0.133
50 1-1/2 553310 446003 50.0 1.97 4.8 0.19 0.145
63 2 553311 446004 63.0 2.48 5.9 0.23 0.154
90 3 553313 446005 90.0 3.55 8.2 0.32 0.216
110 4 553314 446006 110.0 4.34 9.9 0.39 0.237
Pipe 185 PSI (1275 KPa)
Pipe Clip
Coupling Socket
Size d1(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
B C G A D Wt. (oz)*1/2 434306 437341 1.38 1.18 0.63 – 0.55 0.35
*3/4 434407 437342 1.38 1.38 0.67 – 0.63 0.39
*1 434308 437343 1.58 1.58 0.67 – 0.67 0.46
1-1/2 434310 437345 1.97 1.97 0.83 3.35 0.87 1.20
2 434311 437346 2.36 2.36 0.83 4.02 0.75 1.59
3 434313 437348 3.15 3.15 1.22 5.83 1.54 3.88
4 434314 437349 3.54 3.78 1.38 6.73 1.42 5.30
* Without Retaining Clip
DIMENSIONS DATA
DIM
ENSI
ONAL
DAT
A
Duraplus® Air-Line System26 Duraplus® Air-Line System
Airline is metric sized. Equivalent inch sizes are 20 (1/2"), 25 (3/4"), 32 (1"), 50 (1-1/2"), 63 (2"), 90 (3"), 110 (4") 26
DIMENSIONS DATA
90o Elbow – Socket
45o Elbow – Socket
90o Bend – Socket
Sized1 (in)
SignificantNumber
ProductCode
Critical Dimensions (in)
Z1 A C Wt. (oz)
1/2 115306 437111 0.45 0.98 1.11 0.35
3/4 115307 437112 0.55 1.22 1.31 0.60
1 115308 437113 0.70 1.56 1.59 1.24
1-1/2 115310 437114 1.07 2.43 2.34 4.38
2 115311 437115 1.34 3.07 2.87 8.12
3 115313 437117 1.90 4.38 4.01 24.36
4 115314 437118 2.37 5.35 4.87 43.07
Sized1 (in)
SignificantNumber
ProductCode
Critical Dimensions (in)
Z1 A C Wt. (oz)
1/2 115306 437128 0.22 0.98 1.42 0.25
3/4 115307 437129 0.26 1.22 1.62 0.49
1 115308 437130 0.32 1.56 1.89 0.95
1-1/2 115310 437131 0.49 2.43 2.66 3.53
2 115311 437132 0.58 3.07 3.17 6.35
3 115313 437134 0.89 4.40 4.33 19.42
4 115314 437135 1.03 5.35 5.19 33.54
Sized1 (in)
SignificantNumber
ProductCode
Critical Dimensions (in)
Z1 A C Wt. (oz)
3/4 118307 437120 1.96 1.28 2.72 1.34
1 118308 437121 2.51 1.61 3.40 2.65
1-1/2 118310 437122 3.93 2.43 5.20 8.65
2 118310 437123 4.96 3.07 6.48 16.59
3 118313 437125 7.08 4.38 9.19 47.66
4 118314 437126 8.66 5.51 11.16 90.72
DIMEN
SIONAL DATA
27Duraplus® Air-Line System
DIMENSIONS DATA
6
Tee – Socket
Tee – Reducer – Socket
Dropper Bend – Spigot
Sized1 (in)
SignificantNumber
ProductCode
Critical Dimensions (in)
Z1 A C Wt. (oz)
1/2 122306 437151 0.45 0.98 1.11 0.42
3/4 122307 437152 0.55 1.22 1.31 0.85
1 122308 437153 0.70 1.56 1.59 1.69
1-1/2 122310 437154 1.07 2.43 2.34 5.65
2 122311 437155 1.34 3.07 2.87 10.59
3 122313 437157 1.90 4.38 4.04 31.77
4 122314 437158 2.37 5.35 4.87 58.25
Size (in) SignificantNumber
ProductCode
Critical Dimensions (in)
d1 d2 Z1 A B C D Wt. (oz)3/4 1/2 124415 437161 0.55 1.22 2.64 1.22 0.98 0.80
1 1/2 124418 437163 0.70 1.56 3.18 1.54 0.98 1.40
1 3/4 124419 437164 0.70 1.56 3.18 1.45 1.22 1.45
1-1/2 1/2 124424 437166 1.07 2.43 4.68 1.72 0.98 4.94
1-1/2 3/4 124425 437167 1.07 2.43 4.68 1.82 1.22 4.94
1-1/2 1 124426 437168 1.07 2.43 4.68 1.96 1.56 4.94
2 3/4 124429 437169 1.33 3.07 5.75 2.08 1.22 9.20
2 1 124430 437170 1.33 3.07 5.75 2.24 1.57 9.20
2 1-1/2 124432 437171 1.34 3.07 5.74 2.61 2.43 9.53
Size d1(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
B C D H Dev Length Wt. (oz)1/2 437259 312306 2.75 0.78 3.54 3.14 13.00 0.99
3/4 437260 312307 2.95 0.90 3.54 3.36 13.70 1.27
1 437261 312308 3.77 1.02 3.54 5.66 19.20 4.80
DIM
ENSI
ONAL
DAT
A
Duraplus® Air-Line System28 Duraplus® Air-Line System
DIMENSIONS DATA
A d1
CB
B
d1 d2
Z
Z1
B
d3 d2 d1 C
Z2
Z1
Airline is metric sized. Equivalent inch sizes are 20 (1/2"), 25 (3/4"), 32 (1"), 50 (1-1/2"), 63 (2"), 90 (3"), 110 (4") 28
Reducer Bushing – Socket
Reducer Coupling – Socket/Spigot x Socket
Cap – Socket
Size (in) SignificantNumber
ProductCode
Critical Dimensions (in)
d1 d2 Z1 B Wt. (oz)3/4 1/2 109415 437051 0.09 0.75 0.141 3/4 109419 437053 0.13 0.88 0.21
1-1/2 *1/2 109424 437055 0.62 1.27 1.131-1/2 *3/4 109425 437056 0.51 1.27 1.021-1/2 1 109426 437057 0.37 1.27 1.67
2 *3/4 109429 437059 0.74 1.52 2.122 *1 109430 437060 0.63 1.52 1.272 1-1/2 109432 437061 0.25 1.52 1.663 *1-1/2 109432 437062 0.27 2.10 7.053 *2 109433 437063 0.57 2.10 7.914 *2 109449 437065 0.97 2.50 8.904 3 109451 437066 0.39 2.50 7.06
Size (in) SignificantNumber
ProductCode
Critical Dimensions (in)
d1 d2 d3 Z1 Z2 B C Wt. (oz)1/2 3/4 1 114415 437103 0.24 1.00 1.65 0.98 0.42
1 1-1/4 1-1/2 114423 437105 0.39 1.47 2.36 1.56 1.39
2 2-1/4 3 114438 437108 0.50 2.29 3.81 3.07 6.71
Sized1 (in)
SignificantNumber
ProductCode
Critical Dimensions (in)
A B C Wt. (oz)
1/2 149306 437192 0.99 0.81 0.65 0.18
3/4 149307 437193 1.24 0.93 0.77 0.28
1 149308 437194 1.59 1.12 0.88 0.67
1-1/2 149310 437195 2.43 1.62 1.27 1.87
2 149311 437196 3.07 1.97 1.52 3.74
3 149313 437198 4.38 2.10 2.75 10.59
*4 149314 337001 5.37 2.50 3.29 20.12
* Denotes bushing configuration shown in inset. For an example on the use of reducer bushings see page 21.
NOTE: For an example on the use of reducer couplings see page 21.
* Only available in grey
DIMEN
SIONAL DATA
29Duraplus® Air-Line System
DIMENSIONS DATA
8
Stub Flange – Socket
Gasket – Stub Flange (Flat Neoprene)
Cd1
B
A
DZ1
Size d1(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
Z1 A B C D Wt. (oz)1 437181 135308 0.23 1.61 1.96 1.56 1.12 0.67
1-1/2 437182 135310 0.31 2.40 2.87 2.43 1.58 2.12
2 437183 135311 0.31 3.54 1.84 2.99 0.55 3.53
3 437185 135313 0.39 4.92 2.50 4.25 0.62 8.47
4 437186 135314 0.43 5.90 2.93 5.15 0.70 13.06
Size d1(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
A B D K L No Holes Wt. (oz)1 416308 437331 4.48 0.31 1.65 3.26 0.55 4 21.00
1-1/2 425106 437430 5.23 0.19 2.66 3.85 0.63 4 33.00
2 425107 337431 5.98 0.25 3.08 4.75 0.75 4 44.00
3 425109 337433 7.28 0.39 4.33 6.00 0.75 4 57.00
4 425110 337434 8.54 0.39 5.50 7.50 0.75 4 61.00
Size(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
A B D Wt. (oz)
1 411308 437325 1.96 0.11 1.08 0.14
1-1/2 411310 437326 2.87 0.11 1.75 0.25
2 411311 437327 3.54 0.11 2.22 0.35
3 411313 437329 4.92 0.11 3.32 1.06
4 411314 437330 5.90 0.15 4.07 1.41
D
AB
D
B
A
L
K
Backing Ring – Galvanized Mild Steel (ASA 150)
DIM
ENSI
ONAL
DAT
A
Duraplus® Air-Line System30 Duraplus® Air-Line System
DIMENSIONS DATA
G
A
E DC
Z1
d1
F
A
L
K
C
G
T d1
D B
Z1Z2
d1
C
A
NOTE: O-ring gasket – chloroprene rubber. (Viton O-rings are available for conversion.)
NOTE: Seal – Chloroprene rubber. Retaining nut – Brass.
Airline is metric sized. Equivalent inch sizes are 20 (1/2"), 25 (3/4"), 32 (1"), 50 (1-1/2"), 63 (2"), 90 (3"), 110 (4") 30
Blind Flange – ASA 150
Socket Union – Socket
Composite Union – Air-Line to Brass – Socket x Male BSPT
Size(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
A C K L No Holes Wt. (oz)*3 325109 337364 7.24 0.75 6.00 0.75 4 18.34
*4 325110 337365 8.50 0.75 7.50 0.75 8 25.40
* Blind flanges are gray in color.
Size d1(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
Z1 Z2 T A B C D G Wt. (oz)
1/2 205306 437234 0.11 0.39 1.00 0.77 1.04 1.73 0.70 0.74 0.79
3/4 205307 437235 0.11 0.39 1.25 0.10 1.16 2.04 0.78 0.82 1.09
1 205308 437236 0.31 0.39 1.50 1.20 1.28 2.40 0.86 0.90 1.58
1-1/2 205310 437237 0.47 0.55 2.25 1.74 1.82 3.34 0.98 1.14 3.80
2 205311 437238 0.55 0.70 2.75 2.09 2.25 3.93 1.06 1.25 4.08
Size d1(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
Z1 A C D E F G Wt. (oz)
1/2 217306 437237 0.11 0.50 0.07 0.77 1.25 1.57 0.70 4.90
3/4 217307 437238 0.11 0.75 0.07 0.88 1.92 1.88 0.78 7.00
1 217308 437249 0.31 1.00 0.07 1.20 2.08 2.16 0.86 10.50
1-1/2 217310 437250 0.47 1.25 0.07 1.74 2.44 3.07 0.98 22.80
2 217311 437251 0.55 2.00 0.11 2.09 2.71 3.44 1.06 33.30
DIMEN
SIONAL DATA
31Duraplus® Air-Line System
DIMENSIONS DATA
10
Female Adapter – Socket/Spigot x Female BSPT, Reinforced
Female Adapter – Socket x Female BSPT, Reinforced (metric x IPS)
Plug – Male BSPT
A T
Z2
Z1
B
d1 d2
Size (in) SignificantNumber
ProductCode
Critical Dimensions (in)
d1 d2 T Z1 Z2 A B Wt. (oz)1 1-1/2 153341 437231 1.50 0.84 1.26 2.48 2.34 3.81
1-1/2 2 153343 437232 2.00 1.01 1.54 3.05 2.81 5.97
Size (in) SignificantNumber
ProductCode
Critical Dimensions (in)
d1 d2 A B C Z1 Wt. (oz)1/2 x 1/2 101306 437034 1.10 1.41 0.62 0.15 0.42
3/4 x 3/4 101307 437035 1.41 1.57 0.70 0.15 0.67
1 x 1 101308 437036 1.69 1.85 0.82 0.15 1.40
NOTE: This adapter is designed for spigot or socket joining.For an example of the use of the adapter, see page 21
B
A
C
Z1
d2d1
T
B
F
D
Size(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
B D F Wt. (oz)
1/2 155102 337264 0.92 0.55 0.50 0.20
3/4 155103 337265 1.09 0.57 0.55 0.30
1 155104 337266 1.81 0.67 0.68 0.40
1-1/4 155105 337267 13.8 0.85 0.87 1.10
1-1/2 155106 337268 1.50 0.94 1.06 1.30
2 155107 337269 1.77 1.03 1.44 1.80
DIM
ENSI
ONAL
DAT
A
Duraplus® Air-Line System32 Duraplus® Air-Line System
DIMENSIONS DATA
C
A
B
D
E
Z1
Z2
A
C
D
B
T
T2
BE
D F A
C
32
Wall Bracket – Brass Body – ABS Socket x Brass BSPT
Wall Bracket – Multiport – Aluminum MPT (Inlet) x FPT (Outlet)
Gray VKD Ball Valve
Size d1(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
T Z1 Z2 A B C D E Wt. (oz)
1/2 422327 437335 0.50 0.70 0.33 0.61 0.17 0.23 0.74 0.76 6.50
3/4 422328 437336 0.50 0.74 0.43 0.66 0.17 0.19 0.94 0.88 7.60
3/4 422329 437337 0.75 0.74 0.43 0.66 0.17 0.19 0.94 0.27 7.10
Size d1(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
A B C D E F T1 T2 Wt. (oz)
3/4 x 1/2 429122 437338 2.99 3.30 3.70 2.20 2.55 2.20 3/4 npt 1/2 npt 11.60
Size(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
A B C D Wt. (oz)1/2 882306 437451 0.87 2.87 4.63 2.17 0.45
3/4 882307 437452 1.00 3.07 5.07 2.60 0.69
1 882308 437453 1.13 3.26 5.51 2.95 1.00
1-1/2 882310 437454 1.37 3.98 6.73 3.94 1.96
2 882311 437455 1.50 4.72 7.72 4.73 3.37
DIMEN
SIONAL DATA
33Duraplus® Air-Line System
DIMENSIONS DATA
12
FK Butterfly Valve
Size d1(in)
SignificantNumber
ProductCode
Critical Dimensions (in)
B1 B2 C C1 H Z Wt. (lbs)
2 681107 337656 2.76 5.63 6.89 3.94 5.79 1.69 2.38
3 683109 337657 3.66 7.00 10.70 4.33 7.28 1.93 4.11
4 681110 337658 4.21 7.56 10.70 4.33 8.31 2.20 4.88
6 681112 337659 5.30 8.86 12.99 4.33 10.60 2.80 8.47
8 681113 337660 6.34 10.71 16.54 4.80 12.72 2.80 14.35
MAT
ERIA
LDE
SCRI
PTIO
NGE
NER
ALIN
FORM
ATIO
NDE
SIGN
DAT
AH
ANDL
ING
AND
INST
ALLA
TION
DIM
ENSI
ONAL
DAT
ASP
ECIF
ICAT
ION
SAP
PEN
DICE
S
Duraplus® Air-Line System34 Duraplus® Air-Line System
34
This page intentionally
left blank.
SPECIFICATIONS
35Duraplus® Air-Line System
SPECIFICATIONS
Sample Specifications
General
Duraplus ABS Air-Line is designed for industrial compressedair pipe applications where the extremely high-impactresistance and ductility of the material offers some insuranceagainst internal and external shock loadings and site abuseconditions. Its unique combination of ABS properties –non-toxicity, purity, corrosion- and chemical-resistance,toughness, low-hydraulic resistance, and the ability toperform over a wide temperature range 40°F – 120°F(4°C – 49°C), ensures excellent in-service performance andsystem life.
Material Specifications
Pipe shall be manufactured from an Acrylonitrile ButadieneStyrene (ABS) blend, with a co-extruded nylon-liner. Fittingshall be manufactured from an ABS blend.
Material for both pipe and fittings shall be designed with a2 to 1 safety factor for a 30 year lifespan when operatedunder continuous pressure. Pipe and fittings are capable ofwithstanding a continuous working pressure of 185 psi at73°F (1275 kPa at 23°C) in accordance with ASTM D2282and carry a DIN 4102-B2 fire rating.
The material shall have an izod impact resistance value of noless than 8.5 ft.lb/in at 73°F when tested in accordance withASTM D256, method 'A'. Pipe bore contains a co-extrudednylon liner and fittings are manufactured using an alloy blendof ABS and nylon.
Pipe
Pipes shall be manufactured by IPEX and designed inmetric sizes that comply with the dimensional requirementsof DIN 8062, and ISO 161/1.
Fittings
Fittings shall be of the socket type, designed for solventwelding as supplied by IPEX.
Fittings shall be designed and manufactured to withstandthe continuous pressures applicable to the maximumpressure rating of the pipe. The sockets and fittings shallhave a 0°30 taper, the diameter decreasing from the mouthto the root.
Ball Valves - VKD
The valve body, stem, ball and unions shall be made ofDuraplus® ABS compound which shall meet or exceed therequirements of cell classification 43234 according toASTM D3965.
Ball valves shall be double-blocking type with 0-ring cushionsunder the PTFE seats, in-line micro adjustment capabilityand incorporate a spanner wrench in the handle
Butterfly Valves - FK
The valve body shall also be made of glass reinforcedpolypropylene (GRPP) obtained from homopolymerpolypropylene (PPH).
The valve disc shall also be made of ABS compound.
All butterfly valves shall have non wetted stainless steelshafts and a wafer or lug design with ANSI 150 flangeconnections. The liner shall completely isolate the valvebody from the process flow and act as a flange gasket onboth sides of the valve.
Solvent Cement
All joints shall be made with Blue Duraplus Air-Line ABSsolvent cement as supplied by IPEX. The solvent cementshall be designed to withstand continuous applied pressuresup to 185 psi at 73°F.
Design and Installation
The design and installation of ABS pressure systems shall beperformed in accordance with the recommendations detailedin the Handling and Installation section of this manual andin local and national regulations where applicable. To ensurethe full integrity of the completed system, all componentsshall be supplied by IPEX.
APPE
NDI
CES
Duraplus® Air-Line System36 Duraplus® Air-Line System
APPENDICES
Contents of Pipe
Dia.in.
1/45/16
3/87/16
1/29/16
5/811/16
3/413/16
7/815/16
111/411/213/42
21/421/223/43
31/431/233/44
Dia.ft.
.0208
.0260
.0313
.0365
.0417
.0469
.0521
.0573
.0625
.0677
.0729
.0781
.0833
.1042
.1250
.1458
.1667
.1875
.2083
.2292
.2500
.2708
.2917
.3125
.3333
ft.3Also Area
in. ft.2.0003.0005.0008.0010.0014.0017.0021.0026.0031.0036.0042.0048.0055.0085.0123.0168.0218.0276.0341.0413.0491.0576.0668.0767.0873
U.S. Gal.(231 in.3)
.0026
.0040
.0057
.0078
.0102
.0129
.0159
.0193
.0230
.0270
.0312
.0359
.0408
.0638
.0918
.1250
.1632
.2066
.2550
.3085
.3673
.4310
.4998
.5738
.6528
Dia.in.
41/441/243/45
51/451/253/46
61/461/263/47
71/471/273/48
81/481/283/49
91/491/293/410
101/4
Dia.ft.
.3542
.3750
.3958
.4167
.4375
.4583
.4792
.5000
.5208
.5417
.5625
.5833
.6042
.6250
.6458
.6667
.6875
.7083
.7292
.7500
.7708
.7917
.8125
.8333
.8542
ft.3Also Area
in. ft.2.0985.1105.1231.1364.1503.1650.1803.1963.2130.2305.2485.2673.2868.3068.3275.3490.3713.3940.4175.4418.4668.4923.5185.5455.5730
U.S. Gal.(231 in.3)
.7370
.8263
.92051.0201.1241.2341.3491.4691.5941.7241.8591.9992.1442.2952.4502.6112.7772.9483.1253.3053.4923.6823.8794.0814.286
Dia.in.
101/2103/411
111/4111/2113/412
121/213
131/214
141/215
151/216
161/2
Dia.ft.
.8750
.8958
.9167
.9375
.9583
.97921.0001.0421.0831.1251.1671.2081.2501.2921.3331.375
ft.3Also Area
in. ft.2.6013.6303.6600.6903.7213.7530.7854.8523.9218.99401.0691.1471.2271.3101.3961.485
U.S. Gal.(231 in.3)
4.4984.7144.9375.1635.3955.6335.8766.3756.8957.4357.9978.5789.1809.801
10.44011.110
Capacities in Cubic Feet and in United States Gallons (231 Cubic Inches) per Foot of Length
For 1 Foot Length For 1 Foot Length For 1 Foot Length
Volume
Volume of a pipe is computed by:
Where: V = volume (in cubic inches)ID = inside diameter (in inches)π = 3.14159L = length of pipe (in feet)
Weight
1 U.S. gallon @ 50°F....... 8.33 lbs. x sp. gr.1 cubic foot .................... 62.35 lbs. x sp. gr....................................... 7.48 U.S. gal.1 cu. ft. of water @ 50°F . 62.41 lbs.1 cu. ft. of water @ 39.2°F 62.43 lbs.(39.2°F is water temp. at its greatest density)1 kilogram ...................... 2.2 lbs.1 imperial gallon of water. 10.0 lbs.1 pound.......................... 12 U.S. gal ÷ sp. gr....................................... .016 cu. ft. ÷ sp. gr.
Capacity or Flow
1 U.S. gallon per minute (gpm) 0.134 cfm......500 lb. per hr. x sp. gr.......500 lb. per hr. 1 gpm ÷ sp. gr.
1 cu. ft. per minute (cfm) ......449 gph1 cu. ft. per second (cfs) ......449 gpm1 acre foot per day ......227 gpm1 acre inch per hour ......454 gpm1 cubic meter per minute ......264.2 gpm1,000,000 gal. per day ......595 gpmBrake H.P. = (gpm) (total head in ft.) (specific gravity)
(3960) (pump eff.)
APPENDICES
37Duraplus® Air-Line System
APPENDICES
lb./i
n.2
mm
Hg (T
orr)
(at 0
°C)
1.00
0
3.61
27x1
0-2
1.42
23x1
0-2
4.91
16x1
0-1
1.93
37x1
0-2
1.45
04x1
05
1.45
04x1
0-4
1.42
24x1
01
1.45
04x1
01
1.46
96x1
01
6.94
45x1
0-3
4.33
52x1
0-1
2.76
80x1
01
1.00
00
0.39
37
1.35
96x1
01
5.35
25x1
0-1
4.01
47x1
0-4
4.01
47x1
0-3
3.93
71x1
02
4.01
47x1
02
4.06
79x1
02
1.92
23x1
0-1
1.20
00x1
01
7.03
08x1
01
2.54
00
1.00
00
3.45
32x1
01
1.35
95
1.01
97x1
0-3
1.01
97x1
0-2
1.00
003x
103
1.01
97x1
03
1.03
33x1
03
4.88
2x10
-1
3.04
80x1
01
2.03
60
7.35
54x1
0-2
2.89
58x1
0-2
1.00
00
3.93
70x1
0-2
2.95
30x1
0-5
2.95
30x1
0-4
2.89
59x1
01
2.95
30x1
01
2.99
21x1
01
1.41
39x1
0-2
8.82
6x10
-1
5.17
15x1
01
1.86
83
0.73
55
2.54
00x1
01
1.00
00
7.50
06x1
0-4
7.50
06x1
0-3
7.35
56x1
02
7.50
06x1
02
7.60
00x1
02
3.59
1x10
-1
2.24
19x1
01
6.89
48x1
04
2.49
808x
103
9.80
64x1
02
3.38
64x1
04
1.33
32x1
03
1.00
00
1.00
00x1
01
9.80
60x1
05
1.00
00x1
06
1.01
33x1
06
4.78
80x1
02
2.98
90x1
04
6.89
48x1
03
2.49
08x1
02
9.80
64x1
01
3.38
64x1
03
1.33
32x1
02
1.00
00x1
0-1
1.00
00
9.80
60x1
04
1.00
00x1
05
1.01
33x1
05
4.78
80x1
01
2.98
90x1
03
7.03
06x1
0-2
2.53
99x1
0-3
9.99
97x1
0-4
3.45
32x1
0-2
1.35
95x1
0-3
1.01
97x1
0-6
1.01
97x1
0-5
1.00
00
1.01
97
1.03
32
4.88
24x1
0-4
3.04
79x1
0-2
6.89
47x1
0-2
2.49
08x1
0-3
9.80
64x1
0-4
3.38
64x1
0-2
1.33
32x1
0-3
1.00
00x1
0-6
1.00
00x1
0-5
9.80
60x1
0-1
1.00
00
1.01
13
4.78
80x1
0-4
2.98
90x1
0-2
6.80
45x1
0-2
2.45
82x1
0-3
9.67
81x1
0-4
3.34
21x1
0-2
1.31
58x1
0-3
9.86
92x1
0-7
9.86
92x1
0-6
9.67
8x10
-1
9.86
92x1
0-1
1.00
00
4.72
54x1
0-4
2.94
99x1
0-2
1.44
00x1
02
5.20
22
2.04
81
7.07
27x1
01
2.78
45
2.08
86x1
0-3
2.08
85x1
0-2
2.04
82x1
03
2.08
85x1
03
2.11
62x1
03
1.00
00
6.24
27x1
01
2.30
67
8.33
33x1
0-2
3.28
08x1
0-2
1.13
30
4.46
05x1
0-2
3.34
56x1
0-5
3.34
56x1
0-4
3.28
09x1
01
3.34
56x1
01
3.39
00x1
01
1.60
19x1
0-2
1.00
00
in.H
20(a
t +39
.2°F
)cm
H20
(at +
4°C)
in. H
g(a
t +32
°F)
dyne
/cm
2
(1m
bar)
new
ton/
m2
(PAS
CAL)
kgm
/cm
2
bar
atm
. (An
)
ft. H
20(a
t +39
.2°F
)
lb./f
t.2
Give
nlb
./in.
2in
.H20
(at +
39.2
°F)
cmH
20(a
t +4°
C)in
.Hg
(at +
32°F
)m
m H
g (T
orr)
(at 0
°C)
dyne
/cm
2(1
mba
r)ne
wto
n/m
2(P
ASCA
L)kg
m/c
m2
bar
atm
. (A n
)lb
./ft.2
ft.H
20(a
t +39
.2°F
)
BY F
ACTO
R TO
OBT
AIN
MULTIPLY GIVEN NUMBER OF
Frac
tions
1 /64
1 /32
3 /64
1 /16
5 /64
3 /32
7 /64
1 /8 9 /64
5 /32
11 /6
4
3 /16
13 /6
4
7 /32
15 /6
4
1 /4
Deci
mal
s.0
15
62
5
.03
12
5
.04
68
75
.06
25
.07
81
25
.09
37
5
.10
93
75
.12
5
.14
06
25
.15
62
5
.17
18
75
.18
75
.20
31
25
.21
87
5
.23
47
5
.25
0
Mill
i-m
eter
s.3
97
.79
4
1.1
91
1.5
88
1.9
84
2.3
81
2.7
78
3.1
75
3.5
72
3.9
69
4.3
66
4.7
63
5.1
59
5.5
56
5.9
53
6.3
50
Frac
tions
17 /6
4
9 /32
19 /6
4
5 /16
21 /6
4
11 /3
2
23 /6
4
3 /82
5 /64
13 /3
2
27 /6
4
7 /16
29 /6
4
15 /3
2
31 /6
4
1 /2
Deci
mal
s.2
65
62
5
.28
12
5
.29
68
75
.31
25
.32
81
25
.34
37
5
.35
93
75
.37
5
.39
06
25
.40
62
5
.42
18
75
.43
75
.45
31
25
.46
87
5
.48
43
75
.50
0
Mill
i-m
eter
s6
.74
7
7.1
44
7.5
41
7.9
38
8.3
34
8.7
31
9.1
28
9.5
25
9.9
22
10
.31
9
10
.71
6
11
.11
3
11
.50
9
11
.90
6
12
.30
3
12
.70
0
Frac
tions
33 /6
4
17 /3
2
35 /6
4
9 /16
37 /6
4
19 /3
2
39 /6
4
5 /84
1 /64
21 /3
2
43 /6
4
11 /1
6
45 /6
4
23 /3
2
47 /6
4
3 /4
Deci
mal
s
.51
56
25
.53
12
5
.54
68
75
.56
25
.57
81
25
.59
37
5
.60
93
75
.62
5
.64
06
25
.65
62
5
.67
18
75
.68
75
.70
31
25
.71
87
5
.73
43
75
.75
0
Mill
i-m
eter
s1
3.0
97
13
.49
4
13
.89
1
14
.28
8
14
.68
4
15
.08
1
15
.47
8
15
.87
5
16
.27
2
16
.66
9
17
.06
6
17
.46
3
17
.85
9
18
.25
6
18
.65
3
19
.05
0
Frac
tions
49 /6
4
25 /3
2
51 /6
4
13 /1
6
53 /6
4
27 /3
2
55 /6
4
7 /85
7 /64
29 /3
2
59 /6
4
15 /1
6
61 /6
4
31 /3
2
63 /6
4
1
Deci
mal
s.7
65
62
5
.78
12
5
.79
68
75
.81
25
.82
81
25
.83
47
5
.85
93
75
.87
5
.89
06
25
.90
62
5
.92
18
75
.93
75
.95
31
25
.96
87
5
.98
43
75
1.0
00
Mill
i-m
eter
s1
9.4
47
19
.84
4
20
.24
1
20
.63
8
21
.03
4
21
.43
1
21
.82
8
22
.22
5
22
.62
2
23
.01
9
23
.41
6
23
.81
3
24
.20
9
24
.60
6
25
.00
3
25
.40
0
Inch
esIn
ches
Inch
esIn
ches
DECIM
AL
AN
DM
ILLI
METER
EQU
IVALE
NTS
OF
FRACTIO
NS
PRESSU
RE
CON
VERSIO
N
APPE
NDI
CES
Duraplus® Air-Line System38 Duraplus® Air-Line System
APPENDICES
Units ofLength
1 inch
1 foot
1 yard
1 mile
1 millimeter
1 centimeter
1 meter
1 kilometer
in.1
1236-
0.03940.393739.37
-
ft.0.0833
13
52800.00330.03283.2813281
yd.0.02780.3333
11760
-0.01091.0941094
mile---1---
0.6214
mm25.4
304.8914.4
-1
101000
-
cm2.54030.4891.44
-0.100
1100
-
m0.02540.30480.91441609.30.0010.01
11000
km---
1.609--
0.0011
Units of Weight
1 grain
1 ounce
1 pound
1 ton
1 gram
1 kilogram
1 metric ton
grain1
437.57000
-15.43
--
oz.-1
1632,0000.035335.27
35,274
lb.-
0.06251
2000-
2.2052205
ton--
0.00051--
1.1023
gram0.064828.35453.6
-1
1000-
kg-
0.02830.4536907.20.001
11000
metric ton---
0.9072-
0.0011
Multiply units in left column by proper factor below
Units of Density
1 pound/in.3
1 pound/ft.3
1 pound/gal.
1 gram/cm3
1 gram/liter
lb./in.3
1
-
0.00433
0.0361
-
lb./ft.3
17281
7.48162.43
0.0624
lb./gal.231.0
0.13371
8.3450.00835
g/cm3
27.680.01600.1198
10.001
g/liter27,68016.019119.831000.0
1
Multiply units in left column by proper factor below
(1 micron = 0.001 millimeter)
Units of Area
1 inch2
1 foot2
1 acre
1 mile2
1 centimeter2
1 meter2
1 hectare
in.2
1144
--
0.15501550
-
ft.2
0.00691
43,560--
10.76-
acre--1
640--
2.471
mile2
--
0.00161---
cm2
6.452929.0
--1
10,000-
m2
-0.09294047
-0.0001
110,000
hectare--
0.4047259.0
--1
Multiply units in left column by proper factor below
Units ofVolume
1 inch3
1 foot3
1 yard3
1 centimeter3
1 meter3
1 liter
1 U.S. gallon
1 Imp. gallon
in.3
11728
46,6560.061061,02361.025
231277.4
ft.3
-1
27-
35.310.03530.13370.1605
yd.3
-0.0370
1-
1.308---
cm.3
16.38728,317
-1
1,000,0001000.028
3785.44546.1
meter3
-0.02830.7646
-1
0.0010--
liter0.016428.32764.5
0.0010999.97
13.7854.546
U.S. gal.-
7.481202.0
-264.2
0.26421
1.201
Imp. gal.-
6.229168.2
-220.0
0.22000.8327
1
Multiply units in left column by proper factor below
Multiply units in left column by proper factor below
APPENDICES
39Duraplus® Air-Line System
APPENDICES
10.0069414.69614.2230.01930.49120.4335
0.00145
1441
2116.22048.12.78570.7362.4220.89
--1
0.9678-
0.0334--
0.0703-
1.03331-
0.03450.0305
0.010169
mm Hgat 32°F
51.7130.3591
760735.56
125.40022.4187.5006
in. Hgat 32°F2.0359
0.0141429.92128.9580.0394
10.88260.2953
ft. waterat 39.2°F2.307
0.0160233.9032.81
0.04461.133
10.3346
6.8940.04788
-98.0660.13333.3862.988
1
Multiply units in left column by proper factor below
lb./in.2
lb./ft.2
Int. etc.kg/cm2
mm Hgin Hgft H20kPa
kg/cm2Int. etc.lb./ft.2 kPalbs./in.2
Units of Pressure
ft.-lb.1
778.23.08600.7377
2,655,6561,980,000
BTU0.001285
10.0039660.000948
3412.82544.5
g. cal.0.3240252.16
10.2390
860,563641,617
-Joule
1.35561054.94.1833
1--
kw-hr.----1
0.7456
hp-hr.----
1.34121
Multiply units in left column by proper factor belowUnits of Energy
1 foot-pound1 BTU1 gram calorie1 Int. Joule1 Int. kilowatt-hour1 horsepower-hour
hp1-
1.3410-
0.9863
watt75.7
11000
-735.5
kw0.74750.001
1-
0.7355
BTU/min.42.41
0.056956.88
141.83
ft.-lb./sec.550
0.7376737.612.97542.5
ft.-lb./min.33.00044.25
44,254778.2
32.550
g. cal/sec.178.2
0.2390239.04.203175.7
metric hp1.014
0.001361.360
0.02391
Multiply units in left column by proper factor belowUnits of Power (rates of energy use)
1 horsepower1 watt1 kilowatt1 BTU per minute1 metric hp
11.000165
4.18404.18672.3260
0.999841
4.18334.18602.3256
0.239010.23904
11.000650.55592
0.238850.238920.99935
10.55556
0.429930.430001.79881.8000
1
Multiply units in left column by proper factor below
1 absolute Joule/gram1 Int. Joule/gram1 calorie/gram1 int. calorie/gram1 BTU/lb.
Int. cal/g BTU/lb.cal/gInt.
Joule/gAbsoluteJoule/g
Units of Specific Pressure
200223.08
0.06609
12,00013,3853.9657
3025.93375.2
1
11.1154
0.0003305
0.89651
0.0002963
3025.93375.2
1
Multiply units in left column by proper factor below
1 ton (U.S.) comm1 ton (Brit.) comm1 frigorie/hr.
ton (U.S.)comm
ton (Brit.)comm
Frigorie/hr.kg cal/hr.BTU (IT)
/hr.BTU (IT)
/min.
Units of Refrigeration
NOTE: BTU is International Steam Table BTU (IT).1 frigorie = 1 kg cal. (IT)
APPE
NDI
CES
Duraplus® Air-Line System40 Duraplus® Air-Line System
°F
-459.4-450-440-430-420-410-400-390-380-370-360-350-340-330-320-310-300-290-280-273-270-260-250-240-230-220-210-200-190-180-170-160-150-140-130-120-110-100
-90-80-70-60-50-40-30-20-10
0
°C
-273-268-262-257-251-246-240-234-229-223-218-212-207-201-196-190-184-179-173-169-168-162-157-151-146-140-134-129-123-118-112-107-101
-96-90-84-79-73-68-62-57-51-46-40-34-29-23-17.8
°F
123456789
101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960
°C
-17.2-16.7-16.1-15.6-15.0-14.4-13.9-13.3-12.8-12.2-11.7-11.1-10.6-10.0
-9.4-8.9-8.3-7.8-7.2-6.7-6.1-5.6-5.0-4.4-3.9-3.3-2.8-2.2-1.7-1.1-0.60.00.61.11.72.22.83.33.94.45.05.66.16.77.27.88.38.99.4
10.010.611.111.712.212.813.313.914.415.015.6
°F
616263646566676869707172737475767778798081828384858687888990919293949596979899
100110120130140150160170180190200210212220230240250260270280290
°C
16.116.717.217.818.318.919.420.020.621.121.722.222.823.323.924.425.025.626.126.727.227.828.328.929.430.030.631.131.732.232.833.333.934.435.035.636.136.737.237.84349546066717782889299
100104110116121127132138143
°F
300310320330340350360370380390400410420430440450460470480490500510520530540550560570580590600610620630640650660670680690700710720730740750760770780790800810820830840850860870880890
°C
149154160166171177182188193199204210215221227232238243249254260266271277282288293299304310316321327332338343349354360366371377382388393399404410416421427432438443449454460466471477
°F
900910920930940950960970980990
10001020104010601080110011201140116011801200122012401260128013001350140014501500155016001650170017501800185019001950200020502100215022002250230023502400245025002550260026502700275028002850290029503000
°C
482488493499504510516521527532538549560571582593604616627638649660671682693704732760788816843871899927954982
101010381066109311211149117712041232126012881316134313711399142714541482151015381566159316211649
The following formulas may also be used for converting Centigrade or Fahrenheit degrees into the other scales.
Degrees Cent. °C = (°F - 32) Degrees Fahr. °F = °C + 32
Degrees Kelvin °T = °C + 273.2 Degrees Rankine °R = °F + 459.7
TEMPERATURE CONVERSION
59
95
APPENDICES
NOTES
41Duraplus® Air-Line System
NOTES
Duraplus® Air-Line System42
WARRANTY: All of the Company's Products are guaranteed against defects resulting from faulty workmanship or materials. TheCompany will replace, free of charge, including shipping charges for the replacement Products, any Products which are found to bedefective in workmanship or material, provided that the following conditions are met:
a) the Company is promptly notified in writing of such defect immediately upon discovery of same, and the defectiveProduct is promptly returned to the Company; b) the defect is not due, without limitation, to faulty installation, misalignment of Products, vibration, ordinary wear andtear, corrosion, erosion, U.V. degradation, incompatible lubricants, pastes and thread sealants, unusual pressure surges orpulsation, water hammer, temperature shocking, or fouling; andc) the Products have not been altered or modified after leaving the Company's premises.
The warranty period can be specifically limited for certain Products as stated in writing in the Company's literature.
The Company will not allow claims for labor, materials and/or other expenses required to replace the defective Product, or torepair any damage resulting from the use thereof. The Company disclaims any responsibility for the Purchaser's calculations,product drawings or engineering design specifications. The Company's liability is limited to the purchase price applicable tothe product.
It is agreed and understood that the Company's liability in respect to the sale is strictly limited to the replacement of Productsas hereinbefore specified and that the Company shall not, in any event, be liable for any damages whether for the loss of useor business interruption or any other claim for incidental, consequential, special or punitive damages. There is no warranty,condition or representation of any nature whatsoever, expressed or implied, by statute or otherwise, except as herein contained,and the Company disclaims any implied warranties of merchantability and/or fitness of its Products for a special purpose.
This literature is published in good faith and is believed to be reliable. However, IPEX does not represent and/or warrant inany manner the information and suggestions contained in this brochure. Data presented is the result of laboratory tests andfield experience.
IPEX maintains a policy of ongoing product improvement. This may result in modification of features and/orspecifications without notice.
MNINDPIP070319© 2007 IPEX IND0036UC
SALES AND CUSTOMER SERVICE
Canadian Customers call
Toll free: (866) 473-9462
U.S. Customers call
Toll free: (800) 463-9572
www. ipex inc.com
About IPEX
IPEX is a leading supplier of thermoplastic piping systems. We provide our
customers with one of the world’s largest and most comprehensive product
lines. All IPEX products are backed by over 50 years of experience. With
state-of-the-art manufacturing facilities and distribution centers across
North America, the IPEX name is synonymous with quality and
performance.
Our products and systems have been designed for a broad range of
customers and markets. Contact us for information on:
• PVC, CPVC, PP, ABS, PEX and PE pipe and fittings (1/4" to 48")
• Industrial process piping systems
• Double containment systems
• Acid waste systems
• High purity systems
• Municipal pressure and gravity piping systems
• Plumbing and mechanical pipe systems
• PVC electrical systems
• Telecommunications and utility piping systems
• Irrigation systems
• Radiant heating systems
• Cements, primers and accessories