2 (A) 1 (P) 1 (P) 2 (A) Side ported Side mounting Panel mounting Bottom ported (VM100 only) 3 (R) (3 port) 3 (R) (3 port) 3 (R) (3 port) Mounting interchangeable with the conventional model Lightweight Available in vacuum applications (VM100) ap p l ications (VM10 −100 kPa to 1 MPa (VM200: 0 to 1 MPa) 60 g g 90 g ∗ (Conventional model: 95 g) ∗ (Conventional model: 111 g) ∗ Side ported, basic type Side ported Bottom ported Mounting Bracket mounting and bottom mounting are newly added. Piping direction With miniature indicator ∗ Possible to check if air is output to the secondly port. 2/3 Port Mechanical Valve Series VM100/200 Bracket mounting Bottom mounting (Side ported only) ∗ VM100/Bottom ported only VM100 VM200 2 (A) 1 (P) Pneumatic indicator CAT.EUS12-8A-UK New New RoHS
32
Embed
VM100-200-A cat en - SMC ETech 1 Port 2 Port 1 Port 2 Force Force Port 1 Port 2 Port 1 Port 2 Actuated Side ported Bottom ported R port 3 port only R port 3 port only: 2 B;: @ =.>
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
2 (A)1 (P)
1 (P) 2 (A)
Side ported
Side mounting Panel mounting
Bottom ported(VM100 only)
3 (R) (3 port)3 (R) (3 port)
3 (R) (3 port)
Mounting interchangeable with the conventional model
Lightweight
Available in vacuum applications (VM100)apppppppplicationss (VM10ppppppppp−100 kPa to 1 MPa(VM200: 0 to 1 MPa)
60 g gg
90 g
∗ (Conventional model: 95 g)
∗ (Conventional model: 111 g)
∗ Side ported, basic type
Side ported
Bottom ported
Mounting Bracket mounting and bottom mounting are newly added. Piping direction
With miniature indicator∗ Possible to check if air is output to the secondly port.
Lubrication Note 2) Not requiredPort size 1/8 (Rc, NPT, G) M5Weight (Basic) 60 g 67 gBracket part number Note 3) VM1-B —
Note 1) These values have been calculated according to ISO6358 and indicate the fl ow rate under standard conditions with and inlet pressure of 0.6 MPa (relative pressure) and a pressure drop of 0.1 MPa.
Note 2) Use turbine oil Class 1 ISO VG32, if lubricated.Note 3) The bracket can only be used for side mounting of side ported type.
Model
Piping direction Side ported Bottom ported ActuatorBody option Standard With bottom mounting thread — Actuator
part numberAdditional weight
for actuatorNumber of ports 2 port 3 port 2 port 3 port 2 port 3 port
Key selector (2 position) VM120-01-36A VM130-01-36A VM120U-01-36A VM130U-01-36A VM122-M5-36A VM132-M5-36A VM-36A 78 gTwist selector (3 position) 3 port 5 port 3 port 5 port 3 port 5 port
Note 1) It is possible to change the actuator assembly and mount to basic type when an actuator part number is specifi ed in the column.Note 2) For push button (mushroom), push button (fl ush), push button (extended) and individual fastening ring, refer to page 25.Note 3) The handle of the selector (2 position and 3 position) cannot be removed or replaced alone.Note 4) Colour of plunger: Grey (2 port), White (3 port)
�Compact size� Piping options:
Side ported, Bottom ported� Possible to choose mounting method
with side ported:Side mounting, bottom mounting using screws, or mounting with special bracket
�A variety of actuator types
1
Port 2Port 1
Port 2Port 1
ForceForce
Port 1 Port 2
Port 1 Port 2
Actuated Actuated
Side ported Bottom portedR port3 port only
R port3 port only
Non-actuated Non-actuated
How to Order
Number of ports2 2 port3 3 port
55 port
(Twist selector3 position only)
Body option— Side mountingU With bottom mounting thread
Note) U: Applicable only to side ported type
Bracket option— NoneB With bracket
Note) Applicable only to side ported, side mounting type.However, not applicable to twist selector (3 position).Bracket is shipped together, but not assembled.
Suffix for indicator— NoneZ With miniature indicator
Note) Applicable only to bottom ported type
Made to Order (Pages 21, 22)X207 Alternate type, Mushroom push buttonX219 Push-lock turn-reset type, Mushroom push button
Note) Applicable only to push button (mushroom)
Port size01 R1/8
Side ported onlyN01 NPT1/8F01 G1/8M5 M5 x 0.8 Bottom ported only
Piping direction andthe height of plunger0
Side portedLong
1 Short2
Bottom portedLong
3 Short
Suffix for actuator∗
S Hard steel rollerR Red
Colour ofpush button,
selector
B BlackG GreenY Yellow
3 1VM1 A01 01
Actuator type∗
Side ported Bottom portedLong Short Long Short0 1 2 3
Note 1) It is possible to change the actuator assembly and mount to basic type when an actuator part number is specifi ed in the column.Note 2) For push button (mushroom), push button (fl ush), push button (extended) and individual fastening ring, refer to page 25.Note 3) The handle of the selector (2 position and 3 position) cannot be removed or replaced alone.Note 4) Colour of plunger: Grey (2 port), White (3 port)
�Large flow capacity
� Possible to choose mounting method:Side mounting, bottom mounting using screws, or mounting with special bracket
�A variety of actuator types
Specifi cations
Fluid Air/Inert gasOperating pressure range 0 to 1 MPaAmbient and fl uid temperature −5 to 60°C (No freezing)Flow-rate characteristics 1 (P) ⇒ 2 (A) 2 (A) ⇒ 3 (R)
C [dm3/(s·bar)] 4 3.5b 0.4 0.1
Cv 0.87 0.69Q [L/min] (ANR) Note 1) 1088 795
Lubrication Note 2) Not requiredPort size 1/4Weight (Basic) 90 gBracket part number Note 3) VM2-B
Note 1) These values have been calculated according to ISO6358 and indicate the fl ow rate under standard conditions with and inlet pressure of 0.6 MPa (relative pressure) and a pressure drop of 0.1 MPa.
Note 2) Use turbine oil Class 1 ISO VG32, if lubricated.Note 3) The bracket can only be used for side mounting of side ported type.
13
Force
Port 2Port 2
Port 1Port 1
R port3 port only
Non-actuated Actuated
3 S BVM2 0 02 01 A
How to Order
Construction
Number of ports2 2 port3 3 port
55 port
(Twist selector 3 position only)
Body option— Side mountingU With bottom mounting thread
Bracket option— NoneB With bracket
Note) Applicable only to side mounting type.However, not applicable to twist selector (3 position) and foot pedal.Bracket is shipped together, but not assembled.
Made to Order (Pages 21, 22)X207 Alternate type, Mushroom push buttonX219 Push-lock turn-reset type, Mushroom push button
Note) Applicable only to push button (mushroom)
Port size02 R1/4
N02 NPT1/4F02 G1/4 Suffix for actuator∗
S Hard steel rollerR Red
Colour ofpush button,
selector
B BlackG GreenY Yellow
Actuator type∗
00 Basic01 Roller lever02 One way roller lever05 Straight plunger06 Roller plunger07 Cross roller plunger08 Toggle lever30 Push button (Mushroom)32 Push button (Extended)33 Push button (Flush)34 Twist selector (2 position)36 Key selector (2 position)35 Twist selector (3 position)40 Foot pedal ∗ Refer to the table on page 13
for combinations of actuator type and suffi x.
No. Description Material Note1 Valve ADC White coated
2 Plunger Polyacetal2 port Grey3 port White
3 Plunger retainer PBT4 Cover PBT5 Inner valve NBR, Brass6 Spring Stainless steel7 Spring Spring steel
Component Parts
14
2/3 Port Mechanical Valve Series VM200
Series VM200
One way roller leverVM220-02-02AVM230-02-02AVM220-02-02SAVM230-02-02SA
With bottom mounting threadVM220U-02-�AVM230U-02-�A
VM230U-02-35�AVM250U-02-35�A
A-A
A A
36.
5
25
314 x M4 x 0.7(Bottom mounting thread)
VM2-BComponent parts Q’ty
Bracket 1Hexagon socket head cap screw M5 x 35 2Hexagon nut M5 2
3
6.5
31
2 x M4Bottom mounting thread
48.7
(12.
5)
10.5
60
48
35
13
52
1.6
16.5
M5 x 35Bracket mounting bolt
2 x ø5.4 mounting hole∗ For mounting bolt, a hexagon
socket head cap screw is recommended.
20
2/3 Port Mechanical Valve Series VM200
Series VM100/200Made to OrderPlease contact SMC for detailed specifi cations, dimensions and delivery.
Alternate type: When pressing the push button, the valve actuates and its status is self-retained even after your hand has been released. Pressing the button again will restore the valve to its previous status.
The abbreviations F.O.F. / P.T. / O.T. / T.T. shown in this catalogue are detailed below.
F.O.F. P.T
.
O.T
.
T.T
.
P.T
.
O.T
.
T.T
.
¡F.O.F. <Full Operating Force>Required force to total travel position
¡P.T. <Pre-travel>From free position to initial valve operating position
¡O.T. <Over Travel>From initial valve operating position to total travel position
¡T.T. <Total Travel>From free position to total travel position
Design
Warning1. This product cannot be used for applications in
which the pressure must be sealed.Since the VM100 and VM200 are poppet type valves, fl uid fl ows backward when the pressure on port 2 (A) rises. Since the valves are subject to air leakage, they cannot be used for applications such as holding pressure (including vacuum).
2. Not suitable for use as an emergency shutoff valveThis mechanical valve is not designed for safety applications such as an emergency shutoff valve. If the valves are used for the mentioned applications, additional safety measures should be adopted.
Mounting
Warning1. When installing the mechanical operation type
mechanical valves, adjust the position so that the valves do not operate over the operating limit range.Operating over the limit could damage the mechanical valve or actuator, and lead to equipment malfunction.
2. P.T. depends on pressure or differences between the individual product specifi cations. In order to ensure that the valve opens, keep the operating stroke value for the mechanical operation type within the range specifi ed by the following formula.Operating stroke = (P.T. + 0.5 x O.T.) to (P.T. + O.T. – 0.1)
Operating Stroke Range
Series Actuator typeOperating stroke
[mm]
VM100
Basic 2.2 to 2.9Roller lever 4.3 to 5.4
One way roller lever 4.3 to 5.4Straight plunger 2.7 to 3.4Roller plunger 2.7 to 3.4
Cross roller plunger 2.7 to 3.4
VM200
Basic 4 to 4.9Roller lever 8.7 to 10.9
One way roller lever 9.5 to 11.9Straight plunger 4.5 to 5.4Roller plunger 4.5 to 5.4
Cross roller plunger 4.5 to 5.4
For straight and roller plunger types, there is a groove indicating P.T. and T.T. for stroke adjustment.
T.T
.
O.T
.
P.T
. T.T
.
O.T
.
P.T
.
3. Do not make any alterations to the valve body, such as enlarging the body mounting holes.As doing so could lead to unexpected abnormal conditions such as air leakage.
Operation
Warning1. Operate the manual operation type mechanical
valves (such as push button, twist selector and toggle lever types) with your fi nger.The use of equipment such as a cylinder, cam or hammer, can result in the actuator and the valve being damaged.Do not operate over the operation limit. If excessive operation force is applied over total travel position, actuator part can get deformed and lead to equipment malfunction.
Series VM100/200Specific Product Precautions 1Be sure to read before handling.Refer to back cover for Safety Instructions and “Handling Precautions for SMC Products” (M-E03-3) for 3/4/5 Port Solenoid Valve Precautions.
Mounting
Warning
23
2. When operating the mechanical operation type mechanical valves, select the angle and the maximum speed limit of cam and dog so that valves do not operate over the following maximum values.If operated over the maximum values, impact force from cam and dog will be applied to the actuator, leading to damage of the actuator or the valve itself.
Cam and Dog
Series Actuator typeAngle limit of cam and dog
Max. speed limit of cam and dog [m/s]
VM100
Roller lever 30° 0.7 45° 0.3
One way roller lever 30° 0.7 45° 0.3
Straight plunger — 0.2Roller plunger 30° 0.3
Cross roller plunger 30° 0.3
VM200
Roller lever 30° 0.7 45° 0.3
One way roller lever 30° 0.7 45° 0.3
Straight plunger — 0.2Roller plunger 30° 0.3
Cross roller plunger 30° 0.3
Over 45 (Abrupt angle) 45 or less
[Not acceptable] [Acceptable]
Max. travel
Over travel. Exces-sive force is applied due to the maxi-mum travel position being exceeded.
Sufficient travel. The actuator can reach the total travel posi-tion without exces-sive force being ap-plied.
Max. travel
[Not acceptable] [Acceptable]
Cam and Dog Material
Roller material Cam and dog materialSurface fi nish of
cam and dogPolyacetal Steel 6.3 z or lessHard steel Steel, Resin 25 z or less
Caution1. If the operating condition is maintained for long
periods of time, it may take some time for the valve to restart due to the adherence of the seals and there might be a delay for recovery.
Air Supply
Warning1. Operable fl uid is either air or inert gas only.
It cannot be used for corrosive gas and fl uid.
Caution1. Grease is used for the inside of the valves.
Grease may enter into the outlet port of the valve.
2. When using vacuum pressure for the VM100, supply vacuum pressure to P port.
Operating Environment
Warning1. Do not operate it in an area in which fl uids such as
oil, coolant, or water splash on it or dust comes in contact with it.Because it does not have a waterproof or dustproof construction, fluids or dust could enter the valve, leading to malfunction. Therefore, take measures such as providing a protective cover to prevent direct exposure.
2. Do not expose the product to direct sunlight for an extended period of time.
Maintenance
Warning1. Perform inspections on a regular basis as necessary,
such as at the beginning of an operation, to make sure that the mechanical valve operates properly.
2. Do not disassemble, modify or repair the product.This may lead to malfunction of equipment, injury and equipment damage. Please contact SMC for repairs and maintenance of the product.
Series VM100/200 Specific Product Precautions 2Be sure to read before handling.Refer to back cover for Safety Instructions and “Handling Precautions for SMC Products” (M-E03-3) for 3/4/5 Port Solenoid Valve Precautions.
Operation
Warning
24
Series VM100/200Specific Product Precautions 3Be sure to read before handling.Refer to back cover for Safety Instructions and “Handling Precautions for SMC Products” (M-E03-3) for 3/4/5 Port Solenoid Valve Precautions.
Replace the button in the following manner to change colour of the button.
1. Push button (Flush type)¡Installation ——Of the four colours, red, green, black, and
yellow, select and align the protruding portion of the button with the recessed portion of the body and push in.
¡Removal ————Remove the fastening ring and insert the tip of a small flat head screwdriver into the groove of the button to pry it up.
2. Push button (Mushroom and Extended types)At the time of shipment, only 1 button of the colour that you specifi ed is attached to the body.
Mushroom type Extended type
Installation
Align the protruding portion of the button with the recessed portion of the body and push in. (Use the mark on the button as a reference to align the protruding part.)
Align the protruding portion of the button with the recessed portion of the body and push in.
RemovalPlacing your finger under the collar of the button on the side of the mark, tilt it upward.
Remove the fastening ring and insert the tip of a small flat head screwdr iver in to the groove of the button to pry it up.
Groove
Recessed portion
Protrusion
Flush type button
Fastening ring
Mushroomtype button
Mark Extendedtype button
ProtrusionProtrusion
Recessed portion
Groove
How to remove a mushroom type buttonHow to remove at panel mount
Mark Use your thumb topull the button downward.
Support it withyour finger.
Removing the valve as a unit
MarkUse your thumb to pry the button upward.
Replacement Parts1. Use the part numbers listed below to order individual mushroom,
extended, or fl ush type buttons.
Colour Mushroom type button Extended type buttonRed 3402186R 3402187R
Black 3402186B 3402187BGreen 3402186G 3402187GYellow 3402186Y 3402187Y
Colour Flush type buttonRed 3402188R
Black 3402188BGreen 3402188GYellow 3402188Y
2. Use the part number below to order individual fastening ring. Fastening ring: 3402184
How to Change the Buttons
Caution
25
Series VM100/200Specific Product Precautions 4Be sure to read before handling.Refer to back cover for Safety Instructions and “Handling Precautions for SMC Products” (M-E03-3) for 3/4/5 Port Solenoid Valve Precautions.
Series VM-X219 How to Mount Panel
[Task 1] Removing the push button and fastening ringRemove them from the body turning them counterclockwise in the order of the push button and fastening ring.
Fastening ringPush button
[Task 2] Mounting the valve to the panelInsert the valve to the panel and fi x it with a fastening ring.Remove three spacers attached to the valve depending on the panel thickness.
Spacer
Panel
[Task 3] Mounting the push buttonTighten the push button clockwise by hand and further tighten it until load is applied.
Note) When the push button is not tightened enough, the valve may not output correctly after operating the push button. In other cases, the valve outputs temporarily, but when it is in the holding state, the valve may stop outputting. In this situation, tighten the push button again.
Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.SMC CORPORATION Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: 03-5207-8249 FAX: 03-5298-5362
Safety Instructions Be sure to read “Handling Precautions for SMC Products” (M-E03-3) before using.
SMC Corporation (Europe)
1. The compatibility of the product is the responsibility of the person who designs the equipment or decides its specifications.Since the product specified here is used under various operating conditions, its compatibility with specific equipment must be decided by the person who designs the equipment or decides its specifications based on necessary analysis and test results. The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should also continuously review all specifications of the product referring to its latest catalogue information, with a view to giving due consideration to any possibility of equipment failure when configuring the equipment.
2. Only personnel with appropriate training should operate machinery and equipment.The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced.
3. . Do not service or attempt to remove product and machinery/equipment until safety is confirmed.1. The inspection and maintenance of machinery/equipment should only be
performed after measures to prevent falling or runaway of the driven objects have been confirmed.
2. When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power from any appropriate source is cut, and read and understand the specific product precautions of all relevant products carefully.
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety measures if the product is to be used in any of the following conditions. 1. Conditions and environments outside of the given specifications, or use
outdoors or in a place exposed to direct sunlight.2. Installation on equipment in conjunction with atomic energy, railways, air
navigation, space, shipping, vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specifications described in the product catalogue.
3. An application which could have negative effects on people, property, or animals requiring special safety analysis.
4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confirm proper operation.
Warning
Limited warranty and Disclaimer/Compliance Requirements The product used is subject to the following “Limited warranty and Disclaimer” and “Compliance Requirements”.Read and accept them before using the product.
1. The product is provided for use in manufacturing industries.The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary. If anything is unclear, contact your nearest sales branch.
Caution
Limited warranty and Disclaimer1. The warranty period of the product is 1 year in service or 1.5 years after
the product is delivered.∗2)
Also, the product may have specified durability, running distance or replacement parts. Please consult your nearest sales branch.
2. For any failure or damage reported within the warranty period which is clearly our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product.
3. Prior to using SMC products, please read and understand the warranty terms and disclaimers noted in the specified catalogue for the particular products.
∗2) Vacuum pads are excluded from this 1 year warranty.A vacuum pad is a consumable part, so it is warranted for a year after it is delivered. Also, even within the warranty period, the wear of a product due to the use of the vacuum pad or failure due to the deterioration of rubber material are not covered by the limited warranty.
Compliance Requirements1. The use of SMC products with production equipment for the manufacture of
weapons of mass destruction (WMD) or any other weapon is strictly prohibited.
2. The exports of SMC products or technology from one country to another are governed by the relevant security laws and regulations of the countries involved in the transaction. Prior to the shipment of a SMC product to another country, assure that all local rules governing that export are known and followed.
These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC)∗1), and other safety regulations.
∗1) ISO 4414: Pneumatic fluid power – General rules relating to systems. ISO 4413: Hydraulic fluid power – General rules relating to systems. IEC 60204-1: Safety of machinery – Electrical equipment of machines. (Part 1: General requirements) ISO 10218-1: Manipulating industrial robots - Safety. etc.
Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
Caution:
Warning:
Danger :Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.