VIV-CV-1632 Digital Binocular Cameravivitar-experience-image-manager.com/.../en_US/VIV... · 2 Introduction Thank you for purchasing this Digital Binocular Camera. This device can
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
To be able to download photos and videos to your computer using the Vivitar Experience™ Image
Manager Software, you will need the following minimum configuration:
WINDOWS OS
MICROSOFT® Windows XP with Service Pack 3, Windows Vista with Service Pack 1 or
MICROSOFT® Windows 7 or above
Pentium® 4 processor (or above)
1 GB RAM, 250 MB available hard disk space
16-bit Color monitor, 1024 X 768 recommended screen resolution
CD-ROM Drive
QuickTime® 6 or higher
MICROSOFT ® Internet Explorer 7 or higher
Windows Media Player 10 or higher
DirectX 9 or higher
Internet connection required
MACINTOSH OS
Intel Processor running MACINTOSH OS X v10.5.x or later
1 GB RAM, 250 MB available hard disk space
Display: 1024 x 768 or higher-resolution monitor
QuickTime® 6 or higher
CD-ROM Drive
Internet connection required
Note: Make sure the latest compatible Adobe® Flash® Player is installed on your computer.
11
Powering Your Digital Camera ON/OFF
Make sure the battery has been fully charged.
Make sure a Micro SD Memory card Class 4 or above has been inserted into your camera.
Micro SD Memory card up to 32GB - TF Card not included.
POWERING THE CAMERA ON
1) Flip open the LCD monitor.
2) Press the Power button to turn your camera ON.
3) The LCD monitor will light up. A ‘Welcome’ screen appears on the LCD.
4) The camera will be in Video Capture Mode to start.
POWERING THE CAMERA OFF
While the camera is on, you can press and hold the Power button again at any point to turn
your camera OFF. When the screen displays ‘Good Bye’, release the power button and the
camera will then power off.
AUTO POWER OFF – POWER SAVING FEATURE
Your digital camera also has an Auto Power Off feature that automatically turns off your camera
after a specific period of time that your camera is left idle. The ‘Power Save' settings can be set
from ‘Power Save' settings menu in either Photo Capture Mode or Video Capture Mode when
selecting the Camera Settings .
12
Changing Camera Mode
Your camera has four main modes:
1) Video Capture Mode - Use this mode to capture videos with your camera.
2) Photo Capture Mode - Use this mode to capture photos with your camera.
3) Audio Capture Mode - Use this mode to record sound with your camera.
4) Playback Mode (for Videos, Photos and Audio) - Use this mode to review the videos,
photos and audio you have already recorded with your camera.
When the camera is first powered ON, the Video Capture Mode will be active.
The icons that appear on the LCD screen are the best default settings so that you can begin to
capture and enjoy clear quality photos.
To change the active camera mode, make sure the camera is powered ON and press the MODE
button.
When in Video Capture Mode, this icon will display on the top-left corner of the LCD display
When in Photo Capture Mode, this icon will display on the top-left corner of the LCD display
When in Audio Capture Mode, this icon will display on the top-left corner of the LCD display
When in Playback Mode, this icon will display on the top-left corner of the LCD display
13
Navigating the Menus
NAVIGATING THE MENUS FOR PHOTO CAPTURE, VIDEO
CAPTURE AND PLAYBACK MODES
To access the Main Menu for each Mode:
1) Press the MENU button to open the Main Menus for the current mode.
2) Press the DOWN or UP button to select a specific menu.
The selected option appears highlighted.
3) Press the SHUTTER/OK button to confirm and save your selection and open the options for
the menu you have selected.
4) To select a specific option, press the DOWN or UP button and then the SHUTTER/OK
button to save the selected option and return to the Main Menu.
NOTE:
To go back from the submenus or exit the Main Menu, press the MENU button.
NAVIGATING THE MENU FOR GENERAL CAMERA SETTINGS
To access the General Camera Settings Menu:
1) Press the MENU button while in the Photo Capture, Video Capture or Playback Mode.
2) Press the LEFT or RIGHT button to select the General Camera Settings icon .
3) Press the /- DOWN or / UP button to select a specific menu.
4) Press the SHUTTER/OK button to confirm and save your selection and open the options for
the menu you have selected.
5) To select a specific option, press the /- DOWN or / UP button and then the
SHUTTER/OK button to save the selected option and return to the Main Menu.
14
NOTE:
At any time you can press the MENU button to exit the menus and return to the previous
screen.
Once you change a setting, the setting is saved by your camera until you manually change
the setting or restore the camera’s default factory settings.
After selecting your desired setting, some settings appear as an icon on the LCD screen in
Capture Mode – indicating the option selected.
15
Video Capture Mode
The Video Capture Mode allows you to capture videos with your digital camera.
When the camera is first powered ON, the camera will be in Video Capture Mode by default.
TAKING A VIDEO
1) Powering on Your Camera:
Flip open the LCD screen and press the POWER button to turn on the camera.
The Video Capture Mode is the default mode that appears upon powering on your camera.
The Video icon appears on the top left.
2) Selecting the Scene with the LCD Display:
While in Video Capture Mode use the LCD display to direct the camcorder at the scene you
would like to capture.
NOTE: The time available for video capture (as per the installed memory card size and
selected resolution) is shown on the top right of the LCD screen.
3) Digital Zoom Options:
Press the /- DOWN or / UP button to zoom in/out if desired.
You can magnify your subject up to 4 times using the Digital Zoom.
The zoom magnification is displayed on the bottom right of the LCD screen while zooming.
4) Capturing the Video:
START: Press the SHUTTER or OK button to start the video capture.
While Recording:
- The elapsed recording time appears on the top of the LCD screen.
- On the bottom of the LCD screen the Date and Time appear.
STOP: Press the SHUTTER or OK button again to stop recording.
The video is automatically saved to the camera’s Micro SD Memory Card.
16
VIDEO CAPTURE MODE BUTTONS
Button Description
SHUTTER /
OK
START/STOP: Starts and stops the video capture.
ENTERS and SAVES SELECTION: Within the Menu, enters and saves
the selected Menu Option.
MENU
Opens and exits the menu options for Video Capture Mode and General
Camera Settings.
NOTE: Use the UP/DOWN/LEFT/RIGHT buttons to navigate.
MODE
Toggles between the Video Capture Mode, Photo Capture Mode, Audio
Capture Mode and Playback Mode
Video Capture Mode
Photo Capture Mode
Sound Recording Mode
Playback Mode
UP / + ZOOM: Zooms IN
NAVIGATES MENU: Navigates within the Menus.
DOWN / - ZOOM: Zooms OUT
NAVIGATES MENU: Navigates within the Menus.
PLAYBACK Previews the recorded videos, captured photos and audio.
17
VIDEO CAPTURE MODE LCD ICON STATUS DESCRIPTION
The following icons appear on the LCD screen and indicate the selected menu options and
camera status.
Item Function Description
1 Mode Selection
Displays the current selected Mode:
Video Capture Mode
2 White Balance
Displays the selected White Balance Setting.
The White Balance options include:
Auto, Daylight, Cloudy,
Fluorescent, Tungsten
3 Metering
Displays the selected Metering Setting.
The Metering options include:
Center, Multi, Spot
4 Video Resolution
Selection
Displays the selected Resolution Setting.
The Resolution options include:
18
FHD (1920x1080) ; HD (1280x720); D1 (848x480);
640 (640x480); 320 (320x240)
5 Video Counter /
Record Indicator
Standby Mode: Displays the amount of time
available for video capture as per resolution and
memory card size.
Record Mode: Displays the elapsed time as the
video is being recorded.
6 Micro SD Memory Card
Indication
The SD card icon displays when the Micro SD card
has been inserted correctly. The Micro SD card can
then be used as storage for Videos, Photos and
Audio.
7 Date & Time Stamp Record Mode: Displays the date and time while the
video is being recorded.
8 Zoom Indicator Displays the zoom magnification amount as you
press Zoom In and Zoom Out. x1.0 – x4.0
9 Battery Indicator
Displays the current battery level.
The batteries are full.
The batteries are empty. Indication to replace
batteries.
19
VIDEO CAPTURE MODE MENU
ACCESSING THE VIDEO CAPTURE MODE MENU
To access and the Video Capture Mode menu:
1) Press the MENU button to open the Main Menus for the current mode.
2) Press the DOWN or UP button to select a specific menu.
The selected option appears highlighted.
3) Press the SHUTTER/OK button to confirm and save your selection and open the options for
the menu you have selected.
4) To select a specific option, press the DOWN or UP button and then the SHUTTER/OK
button to save the selected option and return to the Main Menu.
NOTE:
At any time you can press the MENU button to exit the menus and return to the previous
screen.
Once you change a setting, the setting is saved by your camcorder until you manually
change the setting or restore the camcorder’s default factory settings.
After selecting your desired setting, some settings appear as an icon on the LCD screen in
Capture Mode – indicating the option that has been selected.
VIDEO CAPTURE MODE MENU OPTIONS
The following option appears in the Video Capture Mode Main Menu:
Menu Name
and Description
Menu Options Menu Options Details
Movie Size
The Movie Size menu allows you to choose
the desired size of the video taken by your
camera. Keep in mind that videos with a
higher resolution will also take up more of
your camera’s memory.
FHD FHD: 1920 x 1080
HD (Default) HD: 1280 x 720
D1 D1: 848 x 480
640 640: 640 x 480
320 320: 320 x 240
Metering
The Metering setting will affect how your
camera focuses when capturing an image.
Center Center – Averages the light metered from the entire frame, but giving greater weight to the subject in the
20
Depending on your selection, the camera will
be more sensitive to focusing on particular
areas in the display and adjust the image
color and lighting accordingly.
Multi (Default)
Spot
center. Multi – Used in standard conditions the camera divides and adjusts the settings of the image into several zones for light metering such as complex light conditions, position of subject, brightness, background, direct light and scenes. Spot – Meters the area within the spot point frame at the center of the LCD to set the exposure on the subject in the center of the monitor.
White Balance
The White Balance feature allows your
camera to adjust the coloring of the captured
images depending on the type of light source
in the current environment.
Properly adjusting the White Balance setting
to match your current environment will allow
the camera to properly balance the colors in
the images that are taken with your camera.
Auto (Default) Automatic white balance.
Daylight White balance selected for
daylight surrounding.
Cloudy White balance selected for
cloudy surrounding.
Fluorescent H White balance selected for
fluorescent surrounding.
Tungsten White balance selected for
tungsten lighting.
Effect
The Effect menu allows you to select a unique
effect that can create an interesting look to
your photo.
Nor Normal (Default)
BW B&W
Sep Sepia
Neg Negative
Red Red
Gre Green
Blu Blue
Displays the selected color
effect on the LCD screen as
you capture your images
with the selected special
effect.
Date Stamp
When you capture a video or photo with your
camera, the image can include a time stamp
with the date and time that the image was
taken.
Off Off
Date Date
D&T Date & Time
(Default)
Off – The date stamp will not
appear on captured images.
Date – The date stamp will
appear on captured images.
Date & Time - The Date and
time stamp will appear on
captured images.
21
Video Playback Mode
The Playback Mode allows you to review and delete photos, videos and audio that you’ve
captured with you camera.
The Playback Mode icon appears on the LCD screen.
When you first power on the camera, the camera will be in Video Capture Mode by default.
To enter Playback Mode:
Press the PLAYBACK button to open the Playback Mode.
Alternatively, after powering on the camera, press the MODE button 3 times to enter Playback
Mode.
To exit Playback Mode:
Press the PLAYBACK or MODE button to exit the Playback Mode and return to Capture
Mode.
The latest captured image appears on the LCD screen. If there are no images stored, a
message (No File) appears.
NOTE:
- The camera does not include a speaker.
- In order to view your captured videos with audio or to hear your audio recordings, please
connect the camera to your computer using the supplied USB cable. You can play videos
and audio files by accessing these files from the camera directly via your computer or by
downloading the files to your computer and then playing from your computer.
- Alternatively, you can play your video and audio files on your TV by connecting an AV
cable (not supplied, must be purchased separately) from the camera’s AV port to your TV.
- For more details see the following sections:
Getting Photos and Videos from the Camera to the Computer
Transferring Images from the Camera to the Computer Manually
Connecting the Camera to a TV
22
VIEWING VIDEOS ON YOUR CAMERA
1) Selecting Your Video:
Once in Playback Mode, press the UP or DOWN button to scroll through the images
on your camera’s memory card until you find the image you would like to view.
- Press the UP button to view the previous image.
- Press the DOWN button to view the next image.
Each captured file (video, photo, audio) is displayed on the LCD screen.
Videos appear with a Video icon on the bottom left of the LCD screen.
2) Playing Your Selected Video – Video Controls:
START: Press the SHUTTER/OK button to start playing your video.
While the video is playing the elapsed time is displayed on the top right.
The video controls are displayed on the bottom. All other Playback icons are not
displayed during playback.
PAUSE/PLAY: Press the UP button to pause the playback, then press the UP
button again to continue playing.
FAST FORWARD: Press the RIGHT button to fast forward while playing your video.
REWIND: Press the LEFT button to rewind while playing your video.
STOP: Press the MENU button to stop playing the video.
23
VIDEO PLAYBACK MODE LCD ICON STATUS DESCRIPTION
The following icons appear on the LCD screen and indicate the selected menu options and
camera status.
Item Function Description
1 Mode Selection
Displays the current selected Mode:
Playback Mode
2 File Counter ;
Elapsed Time
Playback Preview Mode:
Displays number of the current file / Total number
of captured files (photos, videos and audio)
Video Playback:
Displays elapsed time of playing video.
3 Protect/Lock
The lock symbol indicates the file is locked.
Files without the lock symbol indicate that the file is
not locked.
24
4 Video File Icon &
Video Controls
Playback Preview Mode:
The Video icon displays only when there is a
captured video shown in Playback Mode. When a
photo is displayed in the Playback Mode, no icon
is shown on the LCD.
NOTE: If the selected video includes a Date/Time
stamp, the date and time appear on the bottom
right part of the image.
Video Playback:
The Preview Mode icons disappear and the
following video controls are displayed on the
bottom of the screen only during video playback:
- SHUTTER/OK: Play
- UP: Pause / Play
- RIGHT: Fast Forward
- LEFT: Rewind
- MENU: Stop
NOTE: If the selected video includes a Date/Time
stamp, the date and time appear on the right side
of the LCD above the video controls.
25
VIDEO PLAYBACK MODE MENUS
ACCESSING THE VIDEO PLAYBACK MODE MENU
To access and the Video Playback Mode menu:
1) Press the MENU button to open the Main Menus for the current mode.
2) Press the DOWN or UP button to select a specific menu.
The selected option appears highlighted.
3) Press the SHUTTER/OK button to confirm and save your selection and open the options for
the menu you have selected.
4) To select a specific option, press the DOWN or UP button and then the SHUTTER/OK
button to save the selected option and continue to confirm the setting or to return to the
Main Menu.
NOTE:
At any time you can press the MENU button to exit the menus and return to the previous screen.
The following menus appear when a video is selected in Playback Mode:
Menu Name
and Description Menu Options Menu Option Details
Lock Pictures, videos and audio taken with your
camcorder can be protected or “locked” to
prevent any deletion or alteration being made
to the files.
First select the file you would like to lock or
unlock and then select the appropriate menu
option to either lock/protect or
unlock/unprotect one file or all files.
Lock/Unlock One
Lock All
Unlock All
Lock/Unlock One -
Protects/locks or unlocks
the selected media file
(video, photo or audio).
Lock All - Protects/locks all
images (videos, photos and
audio) saved to the
memory card.
Unlock All - Unlocks all
images (videos, photos and
audio) saved to the
memory card.
NOTE:
Locked media files
appear with a lock icon
while viewing the media
26
file in Playback Mode.
Media files that are not
locked do not display the
lock icon.
Locked files cannot be
deleted. You must first
unlock the file(s) and then
select the ‘Delete’ menu
option.
Delete…
While in the Playback Mode, you can delete
pictures, videos and audio from your camera
through the ‘Delete’ menu. You can delete a
single file, or delete all media files saved to
the SD card.
IMPORTANT: Keep in mind that deleting
will permanently remove the selected
images on your camera’s memory card.
One
All
One – Deletes the one
selected file
(photo/video/audio).
All – Deletes all the photos,
videos and audio.
NOTE:
Media files that are
locked cannot be deleted.
First unlock the media
files(s), and then proceed
with deletion.
It is highly recommend
first to save and
download your media
before deleting.
27
Photo Capture Mode
The Photo Capture Mode allows you to capture photos with your digital camcorder.
To enter Photo Capture Mode, power on the camcorder and then press the MODE button once.
The Photo Capture icon appears on the LCD screen.
TAKING A PICTURE
1) Powering on Your Camera:
Flip open the LCD screen and press the POWER button to turn on the camera.
Video Capture Mode is the default mode that appears upon powering on your camera.
Press the MODE button once to enter the Photo Capture Mode.
The Photo Capture icon appears on the top left.
2) Selecting the Scene with the LCD Display:
While in Photo Capture Mode use the LCD display to direct the camcorder at the scene you
would like to capture.
NOTE: The amount of photos available to capture (as per the installed memory card size
and selected resolution) is shown on the top right of the LCD screen.
3) Digital Zoom Options:
Press the /- DOWN or / UP button to zoom in/out if desired.
You can magnify your subject up to 4 times using the Digital Zoom.
The zoom magnification is displayed on the bottom right of the LCD screen while zooming.
4) Capturing the Photo:
Press the SHUTTER or the OK button to take the picture.
The photo is automatically saved to the camera’s Micro SD Memory Card.
NOTE: PHOTOGRAPHING TIPS
Hold the telescope tightly with both hands. Make sure to keep your hands steady when
pressing the Shutter/OK button. If your hands move or shake while pressing the Shutter/OK
button, this may cause the pictures to be blurry.
To ensure high quality pictures, it is recommended to use the tripod.
28
PHOTO CAPTURE MODE BUTTONS
Button Description
SHUTTER /
OK
PHOTO CAPTURE: Takes the picture.
ENTERS and SAVES SELECTION: Within the Menu, enters and saves
the selected Menu Option.
MENU
Opens and exits the menu options for Photo Capture Mode and General
Camera Settings.
NOTE: Use the UP/DOWN/LEFT/RIGHT buttons to navigate.
MODE
Toggles between the Video Capture Mode, Photo Capture Mode, Audio
Capture Mode and Playback Mode
Video Capture Mode
Photo Capture Mode
Sound Recording Mode
Playback Mode
UP / + ZOOM: Zooms IN
NAVIGATES MENU: Navigates within the Menus.
DOWN / - ZOOM: Zooms OUT
NAVIGATES MENU: Navigates within the Menus.
RIGHT
Toggles between the options for Normal Photo Capture Mode (No Icon);
PLAYBACK Previews the recorded videos, captured photos and audio.
29
PHOTO CAPTURE MODE LCD ICON STATUS DESCRIPTION
The following icons appear on the LCD screen and indicate the selected menu options and
camera status.
Item Function Description
1 Mode Selection
Displays the current selected Mode:
Photo Capture Mode
2 Self-Timer / Burst Mode
Displays the selected Self-Timer setting:
The Self-Timer options include:
OFF (no Icon), 2 seconds, 10 seconds
Displays the selected Burst Mode setting:
When Off, no icon appears. When the Burst
setting is selected, the Burst icon appears
and 3 continuous photos are taken when you
press the Shutter/OK button.
3 White Balance Displays the selected White Balance Setting.
30
The White Balance options include:
Auto, Daylight, Cloudy,
Fluorescent, Tungsten
4 Metering
Displays the selected Metering Setting.
The Metering options include:
Center, Multi, Spot
5 Exposure Displays the selected Light Exposure Setting.
The Exposure options include: -2.0EV ~ +2.0EV
6 Photo Resolution
Selection
Displays the selected Resolution Setting.
The Resolution options include:
12M (4000x3000); 9M (3456x2592);
7M (3648×2048 : 16:9) ; 5M (2592x1944);
3M (2048x1536); 2M (1600x1200);
2M (1920x108 : 16:9); 1M 16:9 (1280x720 : 16:9);
1M (1024 x 768); VGA (640×480)
7 Photo Quality
Displays the selected Photo Quality Setting.
The Photo Quality options include:
Super Fine, Fine, Normal
8 Photo Counter
Displays the amount of photos available for photo
capture as per selected photo resolution and memory
card size.
9 Micro SD Memory Card
Indication
The SD card icon displays when the Micro SD card
has been inserted correctly. The Micro SD card can
then be used as storage for Videos, Photos and Audio.
10 Zoom Indicator Displays the zoom magnification amount as you
press Zoom In and Zoom Out. x1.0 – x4.0
11 Battery Indicator
Displays the current battery level.
The batteries are full.
The batteries are empty. Indication to replace
batteries.
31
PHOTO CAPTURE MODE MENU
ACCESSING THE PHOTO CAPTURE MODE MENU
To access and the Photo Capture Mode menu:
1) Press the MENU button to open the Main Menus for the current mode.
2) Press the DOWN or UP button to select a specific menu.
The selected option appears highlighted.
3) Press the SHUTTER/OK button to confirm and save your selection and open the options for
the menu you have selected.
4) To select a specific option, press the DOWN or UP button and then the SHUTTER/OK
button to save the selected option and return to the Main Menu.
NOTE:
At any time you can press the MENU button to exit the menus and return to the previous
screen.
Once you change a setting, the setting is saved by your camcorder until you manually
change the setting or restore the camcorder’s default factory settings.
After selecting your desired setting, some settings appear as an icon on the LCD screen in
Capture Mode – indicating the option that has been selected.
PHOTO CAPTURE MODE MENU OPTIONS
The following option appears in the Photo Capture Mode Main Menu:
Menu Name
and Description
Menu Options Menu Options Details
Resolution
The Resolution menu allows you to choose
the desired size of the video taken by your
camera. Keep in mind that videos with a
higher resolution will also take up more of
your camera’s memory.
12M
9M
7M 16:9
5M (Default)
3M
2M
2M 16:9
1M 16:9
1M
VGA
12M (4000x3000)
9M (3456x2592)
7M 16:9 (3648×2048 : 16:9)
5M (2592x1944)
3M (2048x1536)
2M (1600x1200)
2M 16: 9 (1920x108 : 16:9)
1M 16:9 (1280x720 : 16:9)
1M (1024 x 768)
VGA (640×480)
32
Quality
The Quality menu allows you to select the
desired quality level of the images taken by
your camera. Keep in mind that images with a
higher image quality level will also take up
more memory on your camera.
Super Fine
Fine (Default)
Normal
Selects and displays the
picture Quality setting.
Metering
The Metering setting will affect how your
camera focuses when capturing an image.
Depending on your selection, the camera will
be more sensitive to focusing on particular
areas in the display and adjust the image
color and lighting accordingly.
Center
Multi (Default)
Spot
Center – Averages the light metered from the entire frame, but giving greater weight to the subject in the
center. Multi – Used in standard conditions the camera divides and adjusts the settings of the image into several zones for light metering such as complex light conditions, position of subject, brightness, background, direct light and scenes. Spot – Meters the area within the spot point frame at the center of the LCD to set the exposure on the subject in the center of the monitor.
Sharpness
You can set the level of sharpness in the
images taken with your camera. The
sharpness level dictates if the edges of
objects in the image are more or less distinct
High
Normal (Default)
Low
Selects the Sharpness setting.
Saturation
The Saturation setting allows you to control
the depth of the colors in the image. The
higher the saturation, the more vivid the
colors will be.
High
Normal (Default)
Low
Selects the Saturation setting.
Contrast
The Contrast setting allows you to control the
difference in the bright and dark areas of the
image. If the contrast is high, the image looks
lively; conversely, if the contrast is low, the
image looks more flat and monotonous.
High
Normal (Default)
Low
Selects the Contrast setting.
White Balance Auto (Default)
Automatic white balance.
33
The White Balance feature allows your
camera to adjust the coloring of the captured
images depending on the type of light source
in the current environment.
Properly adjusting the White Balance setting
to match your current environment will allow
the camera to properly balance the colors in
the images that are taken with your camera.
Daylight White balance selected for
daylight surrounding.
Cloudy White balance selected for
cloudy surrounding.
Fluorescent H White balance selected for
fluorescent surrounding.
Tungsten White balance selected for
tungsten lighting.
Exposure
The Light Exposure setting helps you control
the amount of light that enters your camera’s
lens. This setting should be adjusted when
the environment is lighter or darker than
normal.
When the environment has more light than is
needed, reduce the exposure setting (by
using the negative - count) to reduce the
amount of light allowed into the lens by your
camera.
If the environment has less light (darker) than
is needed, increase the exposure setting (by
using the positive + count) to increase the
amount of light allowed into the lens by your
camera.
±2.0
±1.7
±1.3
±1.0
±0.7
±0.3
0 (Default)
Selects and displays the
selected EV± value.
Driver Mode
Self-Timer Mode:
The Self Timer menu allows you to set a
delay between the time that the camera’s
Shutter button is pressed and the actual
capture of the picture. This is an optimal
feature if you don’t just want to take the
picture but would also like to be in the picture
yourself. Just set the Self Timer, press the
Shutter button on your camera and position
yourself in front of the camera as desired.
Burst Mode: When enabled, the ‘Burst Mode’
feature allows you to take three rapid
snapshots in a row with a single click of the
Shutter button.
This feature can be effective when trying to
capture a particular moment in a sporting
event or other scenes with quick movements
Off (Default)
Self-timer 2S
Self-Timer 10S
Burst
Displays the selected
Self-Timer or Burst setting.
OFF - Normal image capture
- one photo at a time
(Default). No icon appears
on the screen.
2S - Sets a 2-second delay
from when you press the
Shutter button until the photo
is taken.
10S - Sets a 10-second
delay from when you press
the Shutter button until the
photo is taken.
Burst - Captures three
continuous photos.
34
Effect
The Effect menu allows you to select a unique
effect that can create an interesting look to
your photo.
Nor Normal (Default)
BW B&W
Sep Sepia
Neg Negative
Red Red
Gre Green
Blu Blue
Displays the selected color
effect on the LCD screen as
you capture your images
with the selected special
effect.
Scene Mode
The Scene menu allows you to choose scene
settings that let your camera to adapt properly
to your current environment.
Auto (Default)
Landscape
Night Scenery
Portrait
Night Portrait
Beach
Sport
Dinner
Displays the selected Scene
setting.
Date Stamp
When you capture a video or photo with your
camera, the image can include a time stamp
with the date and time that the image was
taken.
Off Off
Date Date
D&T Date & Time
(Default)
Off – The date stamp will not
appear on captured images.
Date – The date stamp will
appear on captured images.
Date & Time - The Date and
time stamp will appear on
captured images.
35
Photo Playback Mode
The Playback Mode allows you to review and delete photos, videos and audio that you’ve
captured with you camera.
The Playback Mode icon appears on the LCD screen.
When you first power on the camera, the camera will be in Video Capture Mode by default.
To enter Playback Mode:
Press the PLAYBACK button to open the Playback Mode.
Alternatively, after powering on the camera, press the MODE button 3 times to enter Playback
Mode.
To exit Playback Mode:
Press the PLAYBACK or MODE button to exit the Playback Mode and return to Capture
Mode.
The latest captured image appears on the LCD screen. If there are no images stored, a
message (No File) appears.
VIEWING PHOTOS ON YOUR CAMERA
SELECTING YOUR PHOTO
Once in Playback Mode, press the UP or DOWN button to scroll through the images
on your camera’s memory card until you find the image you would like to view.
- Press the UP button to view the previous image.
- Press the DOWN button to view the next image.
Each captured file (video, photo, audio) is displayed on the LCD screen.
Videos appear with a Video icon on the bottom left of the LCD screen.
Photos appear with no icon on the LCD screen.
36
PHOTO PLAYBACK MODE LCD ICON STATUS DESCRIPTION
The following icons appear on the LCD screen and indicate the selected menu options and
camera status.
Item Function Description
1 Mode Selection
Displays the current selected Mode:
Playback Mode
2 File Counter
Playback Preview Mode:
Displays number of the current file / Total number
of captured files (photos, videos and audio)
3 Protect/Lock
The lock symbol indicates the file is locked.
Files without the lock symbol indicate that the file is
not locked.
37
PHOTO PLAYBACK MODE MENUS
ACCESSING THE PHOTO PLAYBACK MODE MENU
To access and the Photo Playback Mode menu:
1) Press the MENU button to open the Main Menus for the current mode.
2) Press the DOWN or UP button to select a specific menu.
The selected option appears highlighted.
3) Press the SHUTTER/OK button to confirm and save your selection and open the options for
the menu you have selected.
4) To select a specific option, press the DOWN or UP button and then the SHUTTER/OK
button to save the selected option and continue to confirm the setting or to return to the
Main Menu.
NOTE:
At any time you can press the MENU button to exit the menus and return to the previous screen.
The following menus appear when a video is selected in Playback Mode:
Menu Name
and Description Menu Options Menu Option Details
Lock Pictures, videos and audio taken with your
camcorder can be protected or “locked” to
prevent any deletion or alteration being made
to the files.
First select the media file you would like to
lock or unlock and then select the appropriate
menu option to either lock/protect or
unlock/unprotect one file or all files.
Lock/Unlock One
Lock All
Unlock All
Lock/Unlock One -
Protects/locks or unlocks
the selected media file
(video, photo or audio).
Lock All - Protects/locks all
images (videos, photos and
audio) saved to the
memory card.
Unlock All - Unlocks all
images (videos, photos and
audio) saved to the
memory card.
NOTE:
Locked media files
appear with a lock icon
while viewing the media
38
file in Playback Mode.
Media files that are not
locked do not display the
lock icon.
Locked files cannot be
deleted. You must first
unlock the file(s) and then
select the ‘Delete’ menu
option.
Delete…
While in the Playback Mode, you can delete
pictures, videos and audio from your camera
through the ‘Delete’ menu. You can delete a
single media file, or delete all media files
saved to the SD card.
IMPORTANT: Keep in mind that deleting
will permanently remove the selected
images on your camera’s memory card.
One
All
One – Deletes the one
selected file
(photo/video/audio).
All – Deletes all the photos,
videos and audio files.
NOTE:
Media files that are
locked cannot be deleted.
First unlock the file(s),
and then proceed with
deletion.
It is highly recommend
first to save and
download your media
files before deleting.
Slide Show
You can view a Slideshow of all the pictures
taken with your camera while in Playback
Mode. The Slideshow menu allows you to set
the interval length of time that each picture
displays during the Slideshow, the transition
that appears between photos and the looping
of the Slideshow.
The Slideshow menu appears active only
when a photo is selected in Playback Mode.
Start
Interval
Repeat
START: Select ‘Start’ and
press the SHUTTER/OK
button to begin the Slide
Show. The pictures saved
to the Micro SD Memory
card will be displayed in
sequence automatically.
- To PAUSE: Press the
UP button.
- To STOP: Press the
MENU button.
INTERVAL: Select
‘Interval’ and press the
RIGHT/LEFT button to
select an interval time of
1 to 10 seconds between
each photo.
39
REPEAT: Select ‘Repeat’
and press the RIGHT/LEFT
button to select ‘No’ to play
the Slideshow once or ‘Yes’
to continuously loop the
playing of the Slideshow.
Effect
The Effect menu allows you to select a unique
effect that can create an interesting look to
your captured photo.
B&W
Sepia
Negative
Red
Green
Blue
Binarize
Sunset
Warm
Cold
Contrast
Adds the selected effect to
the selected photo. The
edited photo with the effect
is saved as a new file.
40
Audio Capture Mode
The Audio Capture Mode allows you to capture audio clips with your digital camcorder.
To enter Audio Capture Mode, power on the camcorder and then press the MODE button twice.
The Audio Capture icon appears on the LCD screen.
CAPTURING AUDIO
1) Powering on Your Camera:
Flip open the LCD screen and press the POWER button to turn on the camera.
Video Capture Mode is the default mode that appears upon powering on your camera.
Press the MODE button twice to enter the Audio Capture Mode.
The Audio Capture icon appears on the top left.
2) Capturing Audio:
START: Press the SHUTTER or OK button to start recording the audio.
While Recording:
- The elapsed recording time appears in the center of the LCD screen.
- On the top of the LCD screen the remaining time for recording appears, as per the size of
the memory card and the remaining memory on the card.
PAUSE: Press the UP button to pause the audio recording. Press the UP button again to
resume the audio recording.
STOP: Press the SHUTTER or OK button again to stop recording.
The audio is automatically saved to the camera’s Micro SD Memory Card.
41
AUDIO CAPTURE MODE BUTTONS
Button Description
SHUTTER /
OK
AUDIO CAPTURE: Starts and stops the audio recording.
ENTERS and SAVES SELECTION: Within the Menu, enters and saves
the selected Menu Option.
MENU N/A
MODE
Toggles between the Video Capture Mode, Photo Capture Mode, Audio
Capture Mode and Playback Mode
Video Capture Mode
Photo Capture Mode
Sound Recording Mode
Playback Mode
UP / + PAUSE/RECORD: Pauses the audio recording continues the audio
recording.
DOWN / - N/A
PLAYBACK Previews the recorded videos, captured photos and audio.
AUDIO CAPTURE MODE LCD ICON STATUS DESCRIPTION
42
Audio Playback Mode
The Playback Mode allows you to review and delete photos, videos and audio that you’ve
captured with you camera.
The Playback Mode icon appears on the LCD screen.
When you first power on the camera, the camera will be in Video Capture Mode by default.
To enter Playback Mode:
Press the PLAYBACK button to open the Playback Mode.
Alternatively, after powering on the camera, press the MODE button 3 times to enter Playback
Mode.
To exit Playback Mode:
Press the PLAYBACK or MODE button to exit the Playback Mode and return to Capture
Mode.
The latest captured image appears on the LCD screen. If there are no images stored, a
message (No File) appears.
NOTE:
- The camera does not include a speaker.
- In order to view your captured videos with audio or to hear your audio recordings, please
connect the camera to your computer using the supplied USB cable. You can play videos
and audio files by accessing these files from the camera directly via your computer or by
downloading the files to your computer and then playing from your computer.
- Alternatively, you can play your video and audio files on your TV by connecting an AV
cable (not supplied, must be purchased separately) from the camera’s AV port to your TV.
- For more details see the following sections:
Getting Photos and Videos from the Camera to the Computer
Transferring Images from the Camera to the Computer Manually
Connecting the Camera to a TV
43
PREVIEWING AUDIO
1) Selecting Your Audio File:
Once in Playback Mode, press the UP or DOWN button to scroll through the files on
your camera’s memory card until you find the file you would like to view.
- Press the UP button to view the previous image.
- Press the DOWN button to view the next image.
Each captured file (video, photo, audio) is displayed on the LCD screen.
Audio files appear with an Audio icon on the bottom left of the LCD screen.
2) Playing Your Selected Audio – Audio Controls:
START: Press the SHUTTER/OK button to start playing your audio file.
While the audio is playing the elapsed time is appears in the center of the LCD.
The audio controls are displayed on the bottom. All other Playback icons are not
displayed during playback.
PAUSE/PLAY: Press the UP button to pause the playback, then press the UP
button again to continue playing.
FAST FORWARD: Press the RIGHT button to fast forward while playing the audio.
REWIND: Press the LEFT button to rewind while playing the audio.
STOP: Press the MENU button to stop playing the audio.
44
AUDIO PLAYBACK MODE LCD ICON STATUS DESCRIPTION
The following icons appear on the LCD screen and indicate the selected menu options and
camera status.
Item Function Description
1 Mode Selection
Displays the current selected Mode:
Playback Mode
2 File Counter
Playback Preview Mode:
Displays number of the current file / Total number
of captured files (photos, videos, and audio)
3 Protect/Lock
The lock symbol indicates the file is locked.
Files without the lock symbol indicate that the file is
not locked.
4 Elapsed Time
Playback Preview Mode:
No elapsed time shown.
During Audio Playback:
Displays the elapsed time of the playing audio.
1
2
3
4
5
45
5 Audio File Icon /
Audio Controls
Playback Preview Mode:
The Audio icon displays only when there is a
captured audio file shown in Playback Mode.
Audio Playback:
The Preview Mode icons disappear and the
following audio controls are displayed on the
bottom of the screen only during audio playback:
- SHUTTER/OK: Play
- UP: Pause / Resume Playing
- RIGHT: Fast Forward
- LEFT: Rewind
- MENU: Stop
NOTE: While playing the audio file, the elapsed
audio time appears in the center of the screen.
46
AUDIO PLAYBACK MODE MENUS
ACCESSING THE AUDIO PLAYBACK MODE MENU
To access and the Audio Playback Mode menu:
1) Press the MENU button to open the Main Menus for the current mode.
2) Press the DOWN or UP button to select a specific menu.
The selected option appears highlighted.
3) Press the SHUTTER/OK button to confirm and save your selection and open the options for
the menu you have selected.
4) To select a specific option, press the DOWN or UP button and then the SHUTTER/OK
button to save the selected option and continue to confirm the setting or to return to the
Main Menu.
NOTE:
At any time you can press the MENU button to exit the menus and return to the previous screen.
The following menus appear when a video is selected in Playback Mode:
Menu Name
and Description Menu Options Menu Option Details
Lock Pictures, videos and audio taken with your
camcorder can be protected or “locked” to
prevent any deletion or alteration being made
to the files.
First select the media file you would like to
lock or unlock and then select the appropriate
menu option to either lock/protect or
unlock/unprotect one file or all files.
Lock/Unlock One
Lock All
Unlock All
Lock/Unlock One -
Protects/locks or unlocks
the selected media file
(video, photo or audio).
Lock All - Protects/locks all
images (videos, photos and
audio) saved to the
memory card.
Unlock All - Unlocks all
images (videos, photos and
audio) saved to the
memory card.
NOTE:
Locked media files
appear with a lock icon
while viewing the media
47
file in Playback Mode.
Media files that are not
locked do not display the
lock icon.
Locked files cannot be
deleted. You must first
unlock the file(s) and then
select the ‘Delete’ menu
option.
Delete…
While in the Playback Mode, you can delete
pictures, videos and audio from your camera
through the ‘Delete’ menu. You can delete a
single media file, or delete all media files
saved to the SD card.
IMPORTANT: Keep in mind that deleting
will permanently remove the selected
images on your camera’s memory card.
One
All
One – Deletes the one
selected file
(photo/video/audio).
All – Deletes all the photos,
videos and audio files.
NOTE:
Media files that are
locked cannot be deleted.
First unlock the file(s),
and then proceed with
deletion.
It is highly recommend
first to save and
download your media
files before deleting.
48
General Camera Settings
To access the General Camera Settings Menu:
1) Press the MENU button while in the Photo Capture, Video Capture or Playback Mode.
2) Press the LEFT or RIGHT button to select the General Camera Settings icon .
3) Press the /- DOWN or / UP button to select a specific menu.
4) Press the SHUTTER/OK button to confirm and save your selection and open the options for
the menu you have selected.
5) To select a specific option, press the /- DOWN or / UP button and then the
SHUTTER/OK button to save the selected option and return to the Main Menu.
NOTE:
At any time you can press the MENU button to exit the menus and return to the previous
screen.
Once you change a setting, the setting is saved by your camera until you manually change
the setting or restore the camera’s default factory settings.
After selecting your desired setting, some settings appear as an icon on the LCD screen in
Capture Mode – indicating the option selected.
The following menus appear:
Date & Time, Power Frequency, Power Save, Language, TV Out, Format, Reset All
Menu Name
and Description Menu Options Menu Options Details
Date & Time The Date & Time menu allows you to set your
camcorder’s date and time. This date and
time will appear on the captured images when
the Date Stamp is set to be active.
MM/DD/YYYY
HR:MIN.
To set the MM/DD/YY and
Hour: Minutes:
- Press the UP/DOWN
button to change each
setting and specify the
date and time.
- Press the LEFT/RIGHT
button to toggle and
49
move between parts of
the time and date
settings.
- Press OK to save and
confirm the date and time
setting.
Power Frequency The options in the Frequency menu represent
the frequency of the electrical current in
fluorescent lighting sources in your locale. If
your camcorder is set to a frequency that
does not match your country’s electric
current, you may see waves on the images
taken by your camcorder.
50HZ (Default)
60HZ
Selects power frequency in
your location:
50Hz: UK, Europe and
Australia
60Hz: US, Canada and
South America
Power Save You can use the Power Save feature in order
to conserve you camcorder’s battery life. The
designated time represents when your
camcorder will automatically power off.
When the camcorder sits idle for the
designated period of time, the camcorder will
shut off completely and will need to be
powered on again with the power button
before the next use.
Off (Default)
1 min.
3 min.
5min.
OFF - The camcorder
remains on.
1min - The camcorder
powers off after 1 minute of
sitting idle.
3min - The camcorder
powers off after 3 minutes
of sitting idle.
5min - The camcorder
powers off after 5 minutes
of sitting idle.
Language You can select your camera’s language
setting by selecting the desired language
from the Language menu.
English
Chinese Simplified
Traditional Chinese
French
Spanish
Italian
Portuguese
German
Russian
Japanese
Korean
Selects the camera display
language.
TV Out TV Out allows you to select the TV option
appropriate for you to view your captured
media on your television.
NTSC
PAL
Selects the desired TV
setting:
NTSC – television and
video standard used in
50
NOTE: See “Connecting Your Camera to a
TV” for further information on how to connect
your digital video camera to your television.
America, Canada
PAL – television and video
standard used in Europe
Format You can use the Format menu to delete all of
the content that is currently on your camera’s
memory card.
This option will automatically delete all of the
content at one time. If you would like to delete
individual files, use the Delete menu in the
camera’s Playback Mode.
Keep in mind that formatting the
memory card will permanently delete
all of the content on your camera’s
memory card. Please make sure you
have backed up the images that you
want before you proceed with the
format of the memory card.
Yes
No
Formats the Micro SD
Memory Card.
Yes – Automatically deletes
all files on the memory
card.
The memory card will be
completely formatted
No – Does not delete the
files on your memory card.
Exits the ‘Format’ submenu
screen without deleting all
photos, videos and audio
files.
Reset All Use the ‘Reset All’ menu to reset your
camcorder settings to the Factory Default
Settings.
Yes
No
Resets the camera to the
Factory Default Settings.
Yes - Automatically resets
to the Factory Default
Settings.
No - Does not reset to the
Factory Default Settings.
Exits the ‘Reset All’
submenu screen without
resetting and keeps the
current settings.
51
Connecting the Camera to a TV
The camera has an AV port to use your larger TV screen in place of the camera’s LCD screen.
On plugging the TV Cable (not supplied, must be purchased separately) to the camera’s AV out
port and to the TV, the LCD screen turns blank.
Use the camera normally to capture and playback photos and videos.
The images will appear on the TV instead of on the digital video camera’s LCD screen.
NOTE: The only limitation of using the TV screen is that the camera is now not portable.
1) Connect the TV cable:
Connect the black jack into the digital video camera’s AV slot.
Connect the yellow jack into the TV – Video port.
Connect the white jack into the TV – Audio port.
2) Turn On the TV and the digital video camera, and then set the TV to “AV” mode.
3) Make sure you have set the TV format on the camera. You can set this by opening the ‘TV
Out’ menu in the General Camera Settings and selecting the format system suitable to the
format of your TV set (NTSC or PAL).
4) When the camera is set to Video, Photo or Audio Capture Mode, you can preview what you
would like to record on the TV screen and view the recording on the TV.
5) When the camera is set to Playback Mode, you can review all the captured photos, videos
and audio on the TV.
52
Installing the Software
You must be connected to the internet to install and run the Vivitar Experience Image
Manager software.
1) Insert the installation CD into your CD-ROM drive. The installation screen should
automatically open.
2) WINDOWS: The Vivitar Experience™ Image Manager Installer window appears. If the
window does not appear, open the application’s CD/DVD drive and click on “Setup.exe” to
launch the installer.
MACINTOSH: Click the icon that appears on the desktop to install the Vivitar Experience™
Image Manager.
3) If you do not have Internet access at the time of inserting the CD-ROM, connect to the
Internet and then click the “Install Vivitar Experience™ Image Manager” button to begin the
installation.
53
Note: If you do not have Internet access, you can still download media from the camera.
Click the “How to transfer photos and videos from my camera to my computer” button for
instructions.
4) If you have Internet access, the “Choose your language” window opens.
Choose your language and click “Next” to open the next window.
5) Select your camera model from the list and click “Next” to open the next window.
6) Click “Next” to confirm your camera model selection and to install the application.
7) Please wait while the application is being installed on your computer.
8) Please review the license terms.
On WINDOWS and MACINTOSH: Click the “I accept the terms of this license agreement”
and then click “Next” to continue.
9) WINDOWS only: Let the “Vivitar Experience™ Image Manager” installer create the folder to
where the program will be installed, and then click “Install”.
10) Please wait while the application continues the installation process on your computer.
11) WINDOWS: Click the “Close” button when the installation is complete.
Click the “Launch Vivitar Experience™ Image Manager” to open the application.
12) MACINTOSH: Click the “Quit” button when the installation is complete.
Click the “Launch Vivitar Experience™ Image Manager” to open the application.
13) If you close the application you can run the Vivitar Experience™ Image Manager from the
Programs (WINDOWS) or Applications (MACINTOSH) menu on your computer.
Connecting the Camera to the Computer
1) Use the supplied USB cable to connect your camera to your computer.
2) Power the camera ON.
3) The first time you connect the device to the computer you may have to wait a few moments
until the computer recognizes the device.
54
Getting Photos and Videos from the Camera to the
Computer
A memory card needs to be inserted. Do not disconnect the cable during transfer. Doing so will
cancel the transfer of any files on their way to your computer.
1) Select the “Get Images” button from the Main menu.
2) The “Get media from device” window opens.
3) You can select to download photos, videos or both.
4) Select your camera (removable disk) from the device window. If your camera is the only
USB device connected then it will be selected automatically.
5) Select a location on the computer where to place the new photo and video files.
6) Add the new photo and video files to albums if desired.
7) Select to remove the media files from the selected device (removable disk) after the import.
8) Click the “Get Media” button to transfer the photos and videos from your camera to your
computer.
9) A media download progress bar appears on the bottom left showing the number of media
files downloading to your computer. A message appears when the download is complete.
10) The photo and video files that you selected are now downloaded to your computer to the
selected folder and albums ready for your use.
55
Getting Started!
Using the Vivitar Experience™ Image Manager you can:
Upload and manage photos and videos to and from the most popular photo sharing and social