Vehicle Technical Specifications Vehicle: Ford mustang Boss 302 (2012) and GT Class: GTS 6Date Issued: 2/17 Revision Number: 23 Revision Date: 07/10/2015 Page: 1 of 9 Vehicle Manufacturer: Ford Year and Model: Boss 302 (2012) and GT This specifications form was developed by SCCA Pro Racing and will be used by the TECHNCIAL MANAGER to establish technical compliance for vehicles competing in the SCCA PRO RACING WORLD CHALLENGE series. The TECHNICAL MANAGER can also use, but is not limited to also using the following items to check compliance: Electronic Parts Catalog (EPC), Technical Information System (TIS), and the FIA/ASN Homologation forms (or equivalent documentation). The specifications within this form include all modifications that have been approved by SCCA Pro Racing specifically for the vehicle model(s) and year(s) listed on this page. The parts, specifications and assemblies used shall be those for the unmodified stock vehicle, those permitted within the Pro Racing Regulations (PRR) and/or within this VTS. If the stock parts, specifications and/or assemblies exceed the performance potential of those approved with this form, then the parts, specifications and/or assemblies used shall meet those listed within this form. Refer to SCCA PRR and Appendix A. for rules regarding all vehicle specifications not specifically listed within the VTS. The most current rules can be downloaded from the official website: www.world-challenge.com and look under the “Competitors” section for the latest Technical Bulletins, Participant Bulletins, and Appendix A. The Vehicle Technical Specification sheet is a permissive document. The exact configuration of any modification allowed within this VTS is subject to the approval of the TECHNCIAL MANAGER.
9
Embed
Vehicle Technical Specifications - World Challengefiles.world-challenge.com/vehicletech/vts/Ford... · VTS :- 01/2015 Allow Ford cambered Axle kit Part No.# FFR-4001-302 Aluminum
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
Vehicle Technical Specifications Vehicle: Ford mustang Boss 302 (2012) and GT Class: GTS
6Date Issued: 2/17 Revision Number:
23 Revision Date:
07/10/2015 Page: 1 of 9
Vehicle Manufacturer: Ford
Year and Model: Boss 302 (2012) and GT
This specifications form was developed by SCCA Pro Racing and will be used by the TECHNCIAL MANAGER to establish technical compliance for vehicles competing in the SCCA PRO RACING WORLD CHALLENGE series. The TECHNICAL MANAGER can also use, but is not limited to also using the following items to check compliance: Electronic Parts Catalog (EPC), Technical Information System (TIS), and the FIA/ASN Homologation forms (or equivalent documentation). The specifications within this form include all modifications that have been approved by SCCA Pro Racing specifically for the vehicle model(s) and year(s) listed on this page. The parts, specifications and assemblies used shall be those for the unmodified stock vehicle, those permitted within the Pro Racing Regulations (PRR) and/or within this VTS. If the stock parts, specifications and/or assemblies exceed the performance potential of those approved with this form, then the parts, specifications and/or assemblies used shall meet those listed within this form. Refer to SCCA PRR and Appendix A. for rules regarding all vehicle specifications not specifically listed within the VTS. The most current rules can be downloaded from the official website: www.world-challenge.com and look under the “Competitors” section for the latest Technical Bulletins, Participant Bulletins, and Appendix A. The Vehicle Technical Specification sheet is a permissive document. The exact configuration of any modification allowed within this VTS is subject to the approval of the TECHNCIAL MANAGER.
2.L.9.a. Intermediate Port Matching Allowed: 2.L.9.b. Depth from Face:
2.M. Required Engine Seal Locations
2.M.1. Valve Cover Seal #1:
2.M.2. Oil Pan Seal #2:
2.N. Engine Miscellaneous:
“Air cleaner element, housing and ducting from air cleaner to throttle body is unrestricted, however, no ram air or modification to the body to accommodate changes is allowed.” allow the use of Manely rods #14318 Allow alternate side exhaust per rule 2.5.1.1.1.2 Must conform to 2.5.1.1.1.3 The exhaust system must
be adequately isolated from the driver’s compartment.
Vehicle Technical Specifications Vehicle: Ford mustang Boss 302 (2012) and GT Class: GTS
6Date Issued: 2/17 Revision Number:
23 Revision Date:
07/10/2015 Page: 4 of 9
3. Drivetrain
3.A. Transmission 3.A.1. Number of Forward Speeds: 6 3.A.2. Manufacturer: Tremec T-6060
3.A.4. Gear Shift Pattern: H 3.A.5. Gear Engagement synchromesh
3.B. All Wheel Drive System 3.B.1. Transfer Case Manufacturer and Model No.:
NA
3.B.2. Center Differential Type and Manufacturer: NA
3.C. Final Drive 3.C.1. Axle Ratio: 4:30/4.10
3.D. Drivetrain Miscellaneous
TREMAC T 6060 M7003-BossR1 is Approved 2015 VTS :- 01/2015 Allow Ford cambered Axle kit Part No.# FFR-4001-302 Aluminum drive shaft allowed M4602-S Allow use of Ford Racing/Tremec 6060 Transmission M-7003-BOSSR1
Sachs RCS 2/200 clutch allowed
Vehicle Technical Specifications Vehicle: Ford mustang Boss 302 (2012) and GT Class: GTS
6Date Issued: 2/17 Revision Number:
23 Revision Date:
07/10/2015 Page: 5 of 9
4. Suspension 4.A. Suspension Type: 4.A.1. Front: Coil over 4.A.1. Rear: Coil over
4.B. Suspension Miscellaneous
These are factory Ford replacement parts for the boss 302. bumpsteer kit M-3130-R4 rear anti dive brackets M-5650-A Fr lower control arm with extended ball joint M-3075-RA Rr lower control arm M-5649-S Pan hard Bar M-4264 Allow Cortex watts link P/N:CWL-40-302S (Both bracket fully welded to chassis)
5. Chassis 5.A. See Technical Department for information
5.B. Chassis Miscellaneous
Increase size of front rotor to 380mm CM-2300-MGTB VTS : Allow aftermarket Pedal box Part No. TIL72-902 Ford racing brake booster M-2005-R
6. Body 6.A.1. Stock Coefficient of Drag: 6.A.2. Total Frontal Area:
6.B. Body Overhang: 2.B.1. Front: 2.B.2. Rear:
6.C. Stock Body Materials: steel
6.D. Maximum Body Width:
6.E. Permitted Rear Wing Design: CPP-C800-62
6.F. Body Miscellaneous:
CPP-C800-62 62" wing with spec mount and zero degrees rake has to be below the roof line
Permitted Cam Tolerances Camshafts used for this car must meet the specifications above within the following tolerances:
Duration at the seat (From 0.020” lift to 0.030” lift) +/- 6.5 degrees Duration on flank (From 0.100” lift to 0.100” before maximum lift) +/- 4.0 degrees Duration over nose (From 0.100” before maximum lift up to maximum lift) +/- 6.0 degrees Maximum Lift (This tolerance applies to maximum lift only) +/- 0.005 in (0.127 mm)
Vehicle Technical Specifications Vehicle: Ford mustang Boss 302 (2012) and GT Class: GTS
6Date Issued: 2/17 Revision Number:
23 Revision Date:
07/10/2015 Page: 7 of 9
Date Approved – Intial VTS Description TR-16612-EF Fiberglass louvered hood
Date Approved – Intial VTS Description
TR-16612-EC Carbon louvered hood
Vehicle Technical Specifications Vehicle: Ford mustang Boss 302 (2012) and GT Class: GTS
6Date Issued: 2/17 Revision Number:
23 Revision Date:
07/10/2015 Page: 8 of 9
Vehicle Technical Specifications Vehicle: Ford mustang Boss 302 (2012) and GT Class: GTS