VAUXHALL Meriva Owner’s Manual Model Year …...This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently. Make

0 - 1VAUXHALL MerivaVAUXHALL Meriva

Owner’s ManualModel Year 2010.5Edition: January 2010TS 1688-B-10

Introduction .................................... 2In brief ............................................ 6Keys, doors and windows ............ 18Seats, restraints ........................... 32Storage ........................................ 54Instruments and controls ............. 74Lighting ...................................... 105Climate control ........................... 114Driving and operating ................. 121Vehicle care ............................... 141Service and maintenance .......... 180Technical data ........................... 183Customer information ................ 193Index .......................................... 194

Contents

2 Introduction

Introduction

Introduction 3

Vehicle specific dataPlease enter your vehicle's data onthe previous page to keep it easilyaccessible. This information isavailable in the sections "Service andmaintenance" and "Technical data"as well as on the identification plate.

IntroductionYour vehicle is a designedcombination of advanced technology,safety, environmental friendlinessand economy.This Owner's Manual provides youwith all the necessary information toenable you to drive your vehiclesafely and efficiently.Make sure your passengers areaware of the possible risk of accidentand injury which may result fromimproper use of the vehicle.You must always comply with thespecific laws and regulations of thecountry that you are in. These lawsmay differ from the information in thisOwner's Manual.

When this Owner's Manual refers toa workshop visit, we recommend yourVauxhall Authorised Repairer.All Vauxhall Authorised Repairersprovide first-class service atreasonable prices. Experiencedmechanics trained by Vauxhall workaccording to specific Vauxhallinstructions.The customer literature pack shouldalways be kept ready to hand in thevehicle.

Using this manual■ This manual describes all options

and features available for thismodel. Certain descriptions,including those for display andmenu functions, may not apply toyour vehicle due to model variant,country specifications, specialequipment or accessories.

■ The "In brief" section will give youan initial overview.

■ The table of contents at thebeginning of this manual and withineach section shows where theinformation is located.

■ The index will enable you to searchfor specific information.

■ This Owner's Manual depicts left-hand drive vehicles. Operation issimilar for right-hand drive vehicles.

■ The Owner's Manual uses thefactory engine designations. Thecorresponding sales designationscan be found in the section"Technical data".

■ Directional data, e.g. left or right, orfront or back, always relate to thedirection of travel.

■ The vehicle display screens maynot support your specific language.

■ Display messages and interiorlabelling are written in bold letters.

Danger, Warnings andCautions

9 Danger

Text marked 9 Danger providesinformation on risk of fatal injury.Disregarding this information mayendanger life.

4 Introduction

9 Warning

Text marked 9 Warning providesinformation on risk of accident orinjury. Disregarding thisinformation may lead to injury.

Caution

Text marked Caution providesinformation on possible damage tothe vehicle. Disregarding thisinformation may lead to vehicledamage.

SymbolsPage references are indicated with3. 3 means "see page".Thank you for choosing a Vauxhall.We wish you many hours ofpleasurable driving.Your Vauxhall Team

Introduction 5

6 In brief

In brief

Initial drive information

Vehicle unlocking

Press button c to unlock the doorsand load compartment. Open thedoors by pulling the handles. To openthe tailgate, push the touchpad switchunder the tailgate moulding.Radio remote control 3 19, Centrallocking system 3 20, Loadcompartment 3 24.

Seat adjustmentSeat positioning

Pull handle, slide seat, releasehandle.Seat position 3 33, Seat adjustment3 34.

9 Danger

Do not sit nearer than 25 cm fromthe steering wheel, to permit safeairbag deployment.

In brief 7

Seat backrests

Pull lever, adjust inclination andrelease lever. Allow the seat toengage audibly.Seat position 3 33, Seat adjustment3 34.

Seat height

Lever pumping motionup = seat higherdown = seat lower

Seat position 3 33, Seat adjustment3 34.

Seat inclination

Lever pumping motionup = front end higherdown = front end lower

Seat position 3 33, Seat adjustment3 34.

8 In brief

Head restraint adjustment

Press the button, adjust height andengage.To adjust horizontally, pull the headrestraint forwards and engage in oneof three positions. To return to itsrearmost position, pull fully forwardsand release.Head restraints 3 32.

Seat belt

Pull out the seat belt and engage inbelt buckle. The seat belt must not betwisted and must fit close against thebody. The backrest must not be tiltedback too far (maximum approx. 25°).To release belt, press red button onbelt buckle.Seat position 3 33, Seat belts3 41, Airbag system 3 45.

Mirror adjustmentInterior mirror

To reduce dazzle, adjust the lever onthe underside of the mirror housing.Interior mirror 3 28, Automatic anti-dazzle interior mirror 3 28.

In brief 9

Exterior mirrors

Select the relevant exterior mirror andadjust it.Convex exterior mirrors 3 27,Electric adjustment 3 27, Foldingexterior mirrors 3 27, Heatedexterior mirrors 3 27.

Steering wheel adjustment

Unlock the lever, adjust the steeringwheel, then engage the lever andensure it is fully locked.Do not adjust the steering wheelunless the vehicle is stationary andthe steering wheel lock has beenreleased.Airbag system 3 45, Ignitionpositions 3 122.

10 In brief

In brief 11

Instrument panel overview1 Light switch ........................ 105

Headlight rangeadjustment ......................... 106Front fog lights ................... 109Rear fog light ...................... 109Instrument illumination ....... 110

2 Side air vents ...................... 1193 Turn and lane-change

signals, headlight flash,low beam and high beam ... 109Exit lighting ......................... 112Parking lights ...................... 110Driver Information Center ...... 90

4 Cruise control ..................... 1335 Instruments .......................... 806 Horn ..................................... 75

Driver airbag ........................ 457 Driver Information Center ...... 908 Steering wheel controls ........ 749 Windscreen wiper,

windscreen washersystem, rear wiper, rearwasher system ..................... 76

10 Centre air vents .................. 119

11 Infotainment system ............. 1012 Sensor for electronic

climate control system ....... 11613 Info-Display ........................... 9214 Central locking system .......... 20

Hazard warning flashers .... 108Control indicator for airbagdeactivation .......................... 86

15 Traction Control system ..... 131Electronic Stability Control . 132Deflation detection system . 164Ultrasonic parking assist .... 134

16 Front passenger airbag ........ 4517 Glovebox .............................. 54

Fuse box ............................ 16018 Climate control system ........ 11419 Selector lever, manual

transmission ....................... 128Automatic transmission ...... 125

20 Electrical parking brake ....... 13021 Accelerator pedal ............... 12122 Ignition switch with

steering wheel lock ............ 12223 Brake pedal ........................ 12924 Clutch pedal ....................... 121

25 Steering wheel adjustment ... 7426 Storage compartment ......... 16027 Bonnet release lever .......... 142

12 In brief

Exterior lighting

Turn light switchAuto = Automatic light control:

Headlights are switched onand off automatically

m = activation or deactivation ofthe automatic light control

7 = off8 = sidelights9 = headlights

Press light switch> = front fog lightsr = rear fog light

Lighting 3 105.

Headlight flash, high beam andlow beam

headlight flash = pull leverhigh beam = push leverlow beam = push or pull lever

Automatic light control 3 105, Highbeam 3 106, Headlight flash 3 106.

Turn and lane-change signals

lever up = right turn signallever down = left turn signal

Turn and lane-change signals3 109, Parking lights 3 110.

In brief 13

Hazard warning flashers

Operated with the ¨ button.Hazard warning flashers 3 108.

Horn

Press j.

Washer and wiper systemsWindscreen wiper

2 = fast1 = slowP = interval wiping or automatic

wiping with rain sensor§ = off

For a single wipe when thewindscreen wiper is off, press thelever down.Windscreen wiper 3 76, Wiperblade replacement 3 147.

14 In brief

Windscreen washer system

Pull lever.Windscreen washer system 3 76,Washer fluid 3 145.

Rear window wiper and washersystems

Push the rocker switch to activate therear window wiper:upper position = short intervallower position = long intervalmiddle position = off

Push lever.Washer fluid is sprayed on the rearwindow and the wiper wipes a fewtimes.Rear window wiper/washer 3 77.

In brief 15

Climate controlHeated rear window, heatedexterior mirrors

The heating is operated by pressingthe Ü button.Heated rear window 3 30.

Demisting and defrosting thewindows

Press button V.Set the temperature control to thehighest level.Cooling n on.Heated rear window Ü on.Climate control system 3 114.

TransmissionManual transmission

Reverse: with the vehicle stationary,depress the clutch pedal, press therelease button on the selector leverand engage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Manual transmission 3 128.

16 In brief

Automatic transmission

P = parkR = reverseN = neutralD = drive

Manual mode: move selector leverfrom D to the left.< = higher gear] = lower gear

The selector lever can only be movedout of P when the ignition is on andthe brake pedal is applied. To engageP or R, press the release button.Automatic transmission 3 125.

Starting offCheck before starting off■ Tyre pressure and condition3 163, 3 189.

■ Engine oil level and fluid levels3 143.

■ All windows, mirrors, exteriorlighting and number plates are freefrom dirt, snow and ice and areoperational.

■ Proper position of mirrors, seats,and seat belts 3 27, 3 33,3 42.

■ Brake function at low speed,particularly if the brakes are wet.

Starting the engine

■ Turn key to position 1■ move the steering wheel slightly to

release the steering wheel lock■ operate clutch and brake■ automatic transmission in P or N■ do not operate accelerator pedal■ diesel engines: turn the key to

position 2 for preheating and waituntil control indicator ! goes out

■ turn key to position 3 and releaseStarting the engine 3 122.

In brief 17

Parking■ Always apply the parking brake.

Pull switch m.■ Switch off the engine. Turn the

ignition key to 0 and remove it. Turnthe steering wheel until the steeringwheel lock is felt to engage.For vehicles with automatictransmission, the key can only beremoved when the selector lever isin the P position.

■ If the vehicle is on a level surface oruphill slope, engage first gear or setthe selector lever to P beforeswitching off the ignition. On anuphill slope, turn the front wheelsaway from the kerb.If the vehicle is on a downhill slope,engage reverse gear or set theselector lever to P before switchingoff the ignition. Turn the frontwheels towards the kerb.

■ Lock the vehicle with button e onthe radio remote control.Activate the anti-theft alarm system3 25.

■ Do not park the vehicle on an easilyignitable surface. The hightemperature of the exhaust systemcould ignite the surface.

■ Close the windows and the sunroof.■ The engine cooling fans may run

after the engine has been switchedoff 3 142.

■ After running at high engine speedsor with high engine loads, operatethe engine briefly at a low load orrun in neutral for approx.30 seconds before switching off, inorder to protect the turbocharger.

Keys, locks 3 18, Laying the vehicleup for a long period of time 3 141.

18 Keys, doors and windows

Keys, doors andwindows

Keys, locks ................................... 18Doors ........................................... 24Vehicle security ............................ 25Exterior mirrors ............................ 27Interior mirrors ............................. 28Windows ...................................... 28Roof ............................................. 31

Keys, locksKeysReplacement keysThe key number is specified in theCar Pass or on a detachable tag.The key number must be quotedwhen ordering replacement keys as itis a component of the immobilisersystem.Locks 3 177.

Lock cylindersDesigned to free-wheel if they areforcefully rotated without the correctkey or if the correct key is not fullyinserted. To reset, turn cylinder withthe correct key until its slot is vertical,remove key and then re-insert it. If thecylinder still free-wheels, turn the keythrough 180° and repeat operation.

Key with foldaway key section

Press button to extend. To fold thekey, first press the button.

Car PassThe Car Pass contains securityrelated vehicle data and shouldtherefore be kept in a safe place.When the vehicle is taken toa workshop, this vehicle data isneeded in order to perform certainoperations.

Keys, doors and windows 19

Radio remote control

Used to operate:■ Central locking system■ Anti-theft locking system■ Anti-theft alarm system■ Power windowsThe radio remote control has anapproximate range of up to 16 ft. Itcan be restricted by externalinfluences. The hazard warningflashers confirm operation.Handle with care, protect frommoisture and high temperatures andavoid unnecessary operation.

FaultIf the central locking system cannotbe operated with the radio remotecontrol, it may be due to the following:■ Range exceeded■ Battery voltage too low■ Frequent, repeated operation of the

radio remote control while not inrange, which will require re-synchronisation

■ Overload of the central lockingsystem by operating at frequentintervals, the power supply isinterrupted for a short time

■ Interference from higher-powerradio waves from other sources

Unlocking 3 20.

Basic settingsSome settings can be changed in themenu Settings in the Info-Display.Vehicle personalisation 3 99.

Radio remote control batteryreplacementReplace the battery as soon as therange reduces.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.

Key with foldaway key section

20 Keys, doors and windows

Extend the key and open the unit.Replace the battery (battery typeCR 2032), paying attention to theinstallation position. Close the unitand synchronise.

Key with fixed key sectionHave the battery replaced bya workshop.

Radio remote controlsynchronisationAfter replacing the battery, unlock thedoor with the key in the driver's doorlock. The radio remote control will besynchronised when you switch on theignition.

Memorised settingsWhenever the key is removed fromthe ignition lock, the following settingsare automatically memorised by thekey:■ Lighting■ Infotainment system (only CD 400 /

CDC 400)■ Central locking system■ Comfort settings

The saved settings are automaticallyused the next time the memorised keyis inserted into the ignition lock andswitched to position 3 3 122.Precondition is, that Personalizationby driver, or depending on the displaytype, Personalization by remotecontrol in the personal settings of theInfo-Display is activated. This must beset for each used key.Vehicle personalisation 3 99.

Central locking systemUnlocks and locks doors, loadcompartment and fuel filler flap.A pull on an interior door handleunlocks the respective door. Pullingthe handle once more opens the door.NoteIn the event of an accident in whichairbags or belt pretensioners aredeployed, the vehicle isautomatically unlocked.

NoteA short time after unlocking with theremote control the doors are lockedautomatically if no door has beenopened.

Unlocking

Press button c.Two settings are selectable:■ To unlock only the driver's door and

the fuel filler flap, press button conce. To unlock all doors and the

Keys, doors and windows 21

load compartment, press button ctwice,or

■ press button c once to unlock alldoors, load compartment and fuelfiller flap.

The setting can be changed in themenu Settings in the Info-Display.Vehicle personalisation 3 99.The setting can be saved for the keybeing used.Memorised settings 3 20.The doors are automatically lockedagain if neither a door nor the tailgatehas been opened until 2 minutes afterunlocking.

LockingClose doors, load compartment andfuel filler flap.

Press button e.If the driver's door is not closedproperly, the central locking systemwill not work.

Unlocking and opening thetailgate

Press button c when the ignition is offto unlock all doors. The tailgate isreleased to be unlocked and openedby pushing the touchpad switch underthe tailgate moulding.

Central locking buttonLocks or unlocks all doors, the loadcompartment and fuel filler flap fromthe passenger compartment.

22 Keys, doors and windows

Press central locking button: thedoors are locked or unlocked. If thedoors are locked the LED in thebutton illuminates.After locking with the radio remotecontrol the LED in the buttonilluminates for approx. 2 minutes.

Fault in radio remote controlsystemUnlocking

Manually unlock the driver's door byturning the key in the lock. Switch onthe ignition and press the centrallocking button to unlock all doors,load compartment and fuel filler flap.By switching on the ignition, the anti-theft locking system is deactivated3 25.

LockingClose the driver's door, open thepassenger door, press central lockingbutton. The vehicle is locked. Closethe passenger door.

Fault in central locking systemUnlockingManually unlock the driver's door byturning the key in the lock. The otherdoors can be opened by pulling theinterior handle twice. The loadcompartment and fuel filler flapcannot be opened. To deactivate theanti-theft locking system, switch onthe ignition 3 25.

Keys, doors and windows 23

Locking

Insert key into the opening above thelock on inside of the door and operatethe lock by pressing until it clicks.Then close the door. The proceduremust be carried out for each door. Thedriver's door can also be locked fromthe outside with the key. The fuel fillerflap and the tailgate cannot be locked.

Automatic lockingAutomatic locking after driving offThe vehicle is locked automaticallywhile exceeding a speed of 2 mph. Anopening from outside is not possible.

Additionally an opening of the reardoors from inside is not possiblewhen the vehicle speed is above2 mph.

Green LEDs indicate that an openingfrom inside is possible.When the vehicle speed is below2 mph, an opening of the doors fromoutside is possible after:■ opening any door from inside■ pressing the central locking buttonc

Caution

Automatic locking is only activewith ignition on.

Fault in the automatic locking systemIn case of a system fault ^illuminates in the instrument clusterand a warning chime sounds toindicate that the rear doors are notsecured against opening. Informpassengers to keep clear of the doorhandles.Stop immediately and activate thechild lock in both rear doors. If thechild lock is already activated, firstdeactivate and then activate again.The green LEDs will go out and thewarning chime will stop as soon asboth child locks are activated. Pull theinner rear door handles to check if thedoors are locked from inside. Consulta workshop.

24 Keys, doors and windows

Child locks

9 Warning

Use the child locks wheneverchildren are occupying the rearseats.

Using a key or suitable screwdriver,turn the child lock in the rear door tothe horizontal position. The doorcannot be opened from the inside. Fordeactivation turn the child lock to thevertical position.

DoorsRear doorsAutomatic locking 3 23.

Load compartmentTailgateOpening

After unlocking push the touchpadswitch below the tailgate mouldingand open the tailgate.Central locking system 3 20.

Closing

Use one of the interior handles.Do not push the touchpad switchunder the moulding whilst closing asthis will unlock the tailgate again.Central locking system 3 20.

Keys, doors and windows 25

General hints for operatingtailgate

9 Warning

Do not drive with the tailgate openor ajar, e.g. when transportingbulky objects, since toxic exhaustgases, which can not be seen orsmelled, could enter the vehicle.This can cause unconsciousnessand even death.

Caution

Before opening the tailgate checkoverhead obstructions, such asa garage door, to avoid damage ofthe tailgate. Always check themoving area above and behind thetailgate.

NoteThe installation of certain heavyaccessories onto the tailgate mayaffect its ability to remain open.

Vehicle securityAnti-theft locking system

9 Warning

Do not use the system if there arepeople in the vehicle! The doorscannot be unlocked from theinside.

The system deadlocks all the doors.All doors must be closed otherwisethe system cannot be activated.If the ignition was on, the driver's doormust be opened and closed once sothat the vehicle can be secured.Unlocking the vehicle disables themechanical anti-theft locking system.This is not possible with the centrallocking button.

Activating

Press e on the radio remote controltwice within 10 seconds.

Anti-theft alarm systemThe anti-theft alarm system isoperated in conjunction with thecentral locking system.It monitors:■ Doors, tailgate, bonnet■ IgnitionUnlocking the vehicle deactivates theanti-theft alarm system.

26 Keys, doors and windows

Status LED

Status LED is integrated in the centrallocking button.Status during the first 10 seconds ofanti-theft alarm system activation:LEDilluminates

= test, arming delay.

LED flashesquickly

= doors, tailgate orbonnet notcompletely closed,or system fault.

Status after system is armed:LED flashesslowly

= system is armed.

Seek the assistance of a workshop inthe event of faults.

AlarmWhen triggered, the horn sounds, andthe hazard warning lights flashsimultaneously. The number andduration of alarm signals arestipulated by legislation.The alarm can be silenced bypressing any button of the radioremote control or by switching on theignition.The anti-theft alarm system can bedeactivated only by pressing buttonc or by switching on the ignition.If the vehicle's battery is to bedisconnected (e.g. for maintenancework), the alarm siren must bedeactivated as follows: switch theignition on then off, then disconnectthe vehicle's battery within15 seconds.

ImmobiliserThe system is part of the ignition lockand checks whether the vehicle isallowed to be started with the keybeing used.The immobiliser is going to beactivated automatically after the keyhas been removed from the ignitionlock.If the control indicator d flashes whenthe ignition is on, there is a fault in thesystem; the engine cannot be started.Switch off the ignition and then repeatthe start attempt.If the control indicator continuesflashing, attempt to start the engineusing the spare key and seek theassistance of a workshop.NoteThe immobiliser does not lock thedoors. You should always lock thevehicle after leaving it and switch onthe anti-theft alarm system 3 20,3 25.

Control indicator d 3 89.

Keys, doors and windows 27

Exterior mirrorsConvex shapeThe convex exterior mirror reducesblind spots. The shape of the mirrormakes objects appear smaller, whichwill affect the abilty to estimatedistances.

Electric adjustment

Select the relevant exterior mirror byturning the control to left (L) or right(R). Then swivel the control to adjustthe mirror.In position 0 no mirror is selected.

Folding

For pedestrian safety, the exteriormirrors will swing out of their normalmounting position if they are struckwith sufficient force. Reposition themirror by applying slight pressure tothe mirror housing.

Heated

Operated by pressing the Ü button.Heating works with the enginerunning and is switched offautomatically after a short time.

28 Keys, doors and windows

Interior mirrorsManual anti-dazzle

To reduce dazzle, adjust the lever onthe underside of the mirror housing.

Automatic anti-dazzle

Dazzle from following vehicles atnight is automatically reduced.

WindowsManual windowsThe door windows can be opened orclosed with the window winders.

Power windows

9 Warning

Take care when operating thepower windows. Risk of injury,particularly to children.If there are children on the rearseats, switch on the child safetysystem for the power windows.Keep a close watch on thewindows when closing them.Ensure that nothing becomestrapped in them as they move.

Power windows can be operated:■ with ignition on■ within 10 minutes of switching

ignition off■ within 5 minutes of opening or

closing a door

Keys, doors and windows 29

After switching off the ignition,window operation is disabled as soonas the vehicle is locked with the radioremote control.

Operate the switch for the respectivewindow by pushing to open or pullingto close.Pushing or pulling gently to the firstdetent: window moves up or down aslong as switch is operated.Pushing or pulling firmly to the seconddetent and then releasing: windowmoves up or down automatically withenabled safety function. To stopmovement, operate the switch oncemore in the same direction.

Safety functionIf the window glass encountersresistance above the middle of thewindow during automatic closing, it isimmediately stopped and openedagain.

Override safety functionIn the event of closing difficulties dueto frost or the like, pull and hold theswitch. The window moves up withoutsafety function. To stop movement,release and pull the switch oncemore.

Child safety system for rearwindows

Press switch z to deactivate reardoor power windows, the LEDilluminates. To activate, press zagain.

Operating windows from outsideThe windows can be operatedremotely from outside the vehicle.

Press and hold c button to openwindows.Press and hold e button to closewindows.Release button to stop windowmovement.

30 Keys, doors and windows

OverloadIf the windows are repeatedlyoperated within short intervals, thewindow operation is disabled forsome time.

Initialising the power windowsIf the windows cannot be closedautomatically (e.g. afterdisconnecting the vehicle battery),a warning message or a warning codeis displayed in the Driver InformationCenter.Vehicle messages 3 94.Activate the window electronics asfollows:1. Close doors.2. Switch on ignition.3. Pull switch until the window is

closed and keep pulling foradditional 2 seconds.

4. Repeat for each window.

Heated rear window

Operated by pressing the Ü button.Heating works with the enginerunning and is switched offautomatically after a short time.Depending on the engine type, theheated rear window comes onautomatically when the diesel particlefilter is being cleaned.

Sun visorsThe sun visors can be folded down orswivelled to the side to preventdazzling.

If the sun visors have integral mirrors,the mirror covers should be closedwhen driving.A ticket holder is located on the backof the sun visor.

Keys, doors and windows 31

RoofMoonroofDo not affix any stickers to the roof.Do not cover the vehicle usinga tarpaulin.

SunblindThe sunblind is electrically operated.

Press button G or H gently to the firstdetent: the sunblind is opened orclosed as long as the switch isoperated.

Press button G or H firmly to thesecond detent and then release: thesunblind is opened or closedautomatically. To stop movement,operate the switch once more.

Safety functionIf the sunblind encounters resistanceduring automatic closing, it isimmediately stopped and openedagain.

Function standbyOn ignition switch postion 1 thesunblind is operable 3 122.

Initialising of the sunblindIf the sunblind cannot be operated(e.g. after disconnecting the vehiclebattery), activate the electronics asfollows:■ If sunblind is closed, keep the

switch H pressed gently to the firstdetent for 10 seconds.

■ If sunblind is open, keep the switchH pressed until sunblind is fullyclosed. Then release switch shortlyand press it again gently to the firstdetent for 10 seconds.

Relearning of safety functionIf the sunblind does not operatecorrectly after initialising:1. Open sunblind fully by pressing

switch G.2. Release switch and then press

switch G again gently to the firstdetent for approx. 30 seconds.Then close sunblind by pressingswitch H until the sunblind isclosed.

32 Seats, restraints

Seats, restraints

Head restraints ............................ 32Front seats ................................... 33Rear seats ................................... 38Seat belts ..................................... 41Airbag system .............................. 45Child restraints ............................. 49

Head restraints

Position

9 Warning

Only drive with the head restraintset to the proper position.

The upper edge of the head restraintshould be at upper head level. If thisis not possible for extremely tallpeople, set to highest position, andset to lowest position for small people.

AdjustmentHead restraints on front seats

Height adjustmentPress the button, adjust height andengage.

Seats, restraints 33

Horizontal adjustmentTo adjust horizontally, pull the headrestraint forwards and engage in oneof three positions.To return to its rearmost position, pullfully forwards and release.

Active head restraints on front seatsIn the event of a rear-end impact, thefront parts of the active headrestraints are moved slightlyforwards. Thus the head is supportedso that the risk of whiplash injury isreduced.

NoteApproved accessories may only beattached, if the seat is not in use.

Head restraints on rear seats

Height adjustmentPull the head restraint upwards orpress both catches to release andpush the head restraint downwards.

Front seatsSeat position

9 Warning

Only drive with the seat correctlyadjusted.

■ Sit with buttocks as far back againstthe backrest as possible. Adjust thedistance between the seat and thepedals so that legs are slightlyangled when pressing the pedals.Slide the front passenger seat asfar back as possible.

34 Seats, restraints

■ Sit with shoulders as far backagainst the backrest as possible.Set the backrest rake so that it ispossible to easily reach thesteering wheel with arms slightlybent. Maintain contact betweenshoulders and the backrest whenturning the steering wheel. Do notangle the backrest too far back. Werecommend a maximum rake ofapprox. 25°.

■ Adjust the steering wheel 3 74.■ Set seat height high enough to

have a clear field of vision on allsides and of all display instruments.There should be at least one handof clearance between head and theroof frame. Your thighs should restlightly on the seat without pressinginto it.

■ Adjust the head restraint 3 32.■ Adjust the height of the seat belt3 42.

■ Adjust the thigh support so thatthere is a space approx. two fingerswide between the edge of the seatand the hollow of the knee.

■ Adjust the lumbar support so that itsupports the natural shape of thespine.

Seat adjustment

9 Danger

Do not sit nearer than 25 cm fromthe steering wheel, to permit safeairbag deployment.

9 Warning

Never adjust seats while driving asthey could move uncontrollably.

Seat positioning

Pull handle, slide seat, releasehandle.

Seats, restraints 35

Seat backrests

Pull lever, adjust inclination andrelease lever. Allow the backrest toengage audibly.

Seat height

Lever pumping motionup = seat higherdown = seat lower

Seat inclination

Lever pumping motionup = front end higherdown = front end lower

36 Seats, restraints

Lumbar support

Adjust lumbar support using the four-way switch to suit personalrequirements.Moving support up and down: pushswitch up or down.Increasing and decreasing support:push switch forwards or backwards.

Adjustable thigh support

Pull the lever and slide the thighsupport.

ArmrestDetachable armrest

Pull handle and fold the armrest lidupwards. The armrest containsa storage compartment.

Seats, restraints 37

Installing armrest

Press the rear button and insert therear guide pins into the upper guiderails. Release the button.

Lower the armrest at the front. Pull thefront handle firmly and insert the frontguide pins into the upper guide rails.Release the handle. Move thearmrest until it engages audibly.

Moving armrest

Pull the front handle slightly and movethe armrest to the desired position.Release the handle. Move thearmrest until it engages audibly.If a cupholder is installed in the lowerguide rail, make sure that the frame ofthe cupholder is in the initial position.NoteIf too much weight is put on thearmrest, it might unlatch. Ease ofmovement might be restricted. Liftthe armrest slightly to latch again.

Armrest storage 3 57.Cupholders 3 54.

38 Seats, restraints

Removing armrestPull the front handle firmly and raisethe armrest at the front. Press the rearbutton and remove the armrest.The armrest can also be installed onthe folded centre rear seat 3 40.

Heating

Adjust heating to the desired settingby pressing the ß button for therespective seat one or more timeswith the ignition on. The controlindicator in the button indicates thesetting.

Prolonged use of the highest settingfor people with sensitive skin is notrecommended.Seat heating is operational whenengine is running.

Rear seats

Seat adjustment

9 Warning

Only drive with the outer seatsengaged in the guide rails.

9 Warning

Never adjust seats while driving asthey could move uncontrollably.

Seats, restraints 39

The rear outboard seats can beindividually moved forward orbackward. The seats are movable inlongitudinal and transversal direction.In longitudinal direction the seats canbe engaged in intermediate positions.Pull handle, slide seat, releasehandle and allow seat to engage.

Flexible Seat System(FlexSpace)

The rear seat row can be adjustedwith two seats providing maximumseating space in position 1, or withthree seats in position 2. In position1 the centre seat is lowered.

The outboard seats can be movedforward into position 3.

Moving seats to position 1

Pull the strap and fold down thecentre seat.

Pull handle and slide the seattransversely backward into position1. The seat is automatically guidedinward. Release handle and allowseat to engage in position.

40 Seats, restraints

Moving seats to position 2

Pull handle and slide the seattransversely forwards into position 2.The seat is automatically guidedoutward. Release handle and allowseat to engage in position.

9 Warning

Move the armrest to the foremostposition or detach the armrestbefore raising the rear centrebackrest.Armrest 3 36.

Pull the strap and raise the centreseat.The centre seat is not usable if theouter seats are moved forward inposition 3.

ArmrestAn armrest adapter can be installedon the seatback of the centre seat.A detachable armrest or a cupholdercan be attached to the adapter.

Installing the adapterPull the strap and fold down thecentre seat 3 38.

Insert the hooks of the adapter intothe recesses of the seatback andpush the adapter forwards.

Seats, restraints 41

Lock the adapter by turning theignition key clockwise in the lock. Theadapter is locked properly when thered mark is visible.Mount the armrest or the cupholderon the adapter.Armrest 3 36, Cupholder 3 54.

Removing the adapterDetach the armrest or the cupholderfrom the adapter.Armrest 3 36, Cupholder 3 54.Unlock the adapter by turning theignition key anticlockwise in the lock.The adapter is unlocked when thegreen mark is visible.Push the adapter rearward andremove.

Seat belts

The seat belts are locked duringheavy acceleration or deceleration ofthe vehicle holding the occupants inthe sitting position. Thereby the risk ofinjury is considerably reduced.

9 Warning

Fasten seat belt before each trip.In the event of an accident, peoplenot wearing seat belts endangertheir fellow occupants andthemselves.

Seat belts are designed to be used byonly one person at a time. They arenot suitable for people smaller than5 ft. Child restraint system 3 49.Periodically check all parts of the beltsystem for damage and properfunctionality.Have damaged componentsreplaced. After an accident, have thebelts and triggered belt pretensionersreplaced by a workshop.NoteMake sure that the belts are notdamaged by shoes or sharp-edgedobjects or trapped. Prevent dirt fromgetting into the belt retractors.

Seat belt reminder X 3 85.

Belt force limitersOn the front seats, stress on the bodyis reduced by the gradual release ofthe belt during a collision.

Belt pretensionersIn the event of a head-on or rear-endcollision of a certain severity, the frontseat belts are tightened.

42 Seats, restraints

9 Warning

Incorrect handling (e.g. removal orfitting of belts) can trigger the beltpretensioners.

Deployment of the belt pretensionersis indicated by illumination of controlindicator v 3 85.Triggered belt pretensioners must bereplaced by a workshop. Beltpretensioners can only be triggeredonce.NoteDo not affix or install accessories orother objects that may interfere withthe operation of the beltpretensioners. Do not make anymodifications to belt pretensionercomponents as this will invalidatethe vehicle type approval.

Three-point seat beltFastening seat belt

Withdraw the belt from the retractor,guide it untwisted across the bodyand insert the latch plate into thebuckle. Tighten the lap belt regularlywhilst driving by pulling the shoulderbelt.Seat belt reminder 3 85.

Loose or bulky clothing prevents thebelt from fitting snugly. Do not placeobjects such as handbags or mobilephones between the belt and yourbody.

9 Warning

The belt must not rest against hardor fragile objects in the pockets ofyour clothing.

Seats, restraints 43

Height adjustment

1. Pull belt out slightly.2. Press button.3. Adjust height and engage.

Adjust the height so that the belt liesacross the shoulder. It must not lieacross the throat or upper arm.Do not adjust while driving.

Removing seat belt

To release belt, press red button onbelt buckle.

Seat belts on the rear seatsPull latch plates out of belt retainer inroof.

44 Seats, restraints

Click bottom latch plate into right-hand buckle (1) at centre seat.Remove top latch plate from retainer,guide over shoulder and lap area withbelt (do not twist) and click into left-hand buckle (2) at centre seat.To remove the seat belt, first pressthe button on the left-hand buckle (2)and remove top latch plate. Thenpress the button on the right-handbuckle (1) and remove bottom latchplate. The seat belt retractsautomatically.

Push the top latch plate into theretainer. Fold over locked togetherlatch plates against the seat belt.

Insert in the seat belt holder in the roofwith the lower latch plate pointingforward.

Using the seat belt while pregnant

9 Warning

The lap belt must be positioned aslow as possible across the pelvisto prevent pressure on theabdomen.

Seats, restraints 45

Airbag systemThe airbag system consists ofa number of individual systemsdepending on the scope ofequipment.When triggered the airbags inflatewithin milliseconds. They also deflateso quickly that it is often unnoticeableduring the collision.

9 Warning

If handled improperly the airbagsystems can be triggered in anexplosive manner.

NoteThe airbag systems and beltpretensioner control electronics arelocated in the centre console area.Do not put any magnetic objects inthis area.Do not stick anything on the airbagcovers and do not cover them withother materials.Each airbag is triggered only once.Have deployed airbags replaced bya workshop. Furthermore, it might benecessary to have the steeringwheel, the instrument panel, parts ofthe panelling, the door seals,handles and the seats replaced.Do not make any modifications tothe airbag system as this willinvalidate the vehicle type approval.

When the airbags inflate, escapinghot gases may cause burns.Control indicator v for airbag systems3 85.

Front airbag systemThe front airbag system consists ofone airbag in the steering wheel andone in the instrument panel on thefront passenger side. These can beidentified by the word AIRBAG.

There are also warning labels on bothsides of the sunblind on the frontpassenger side.The front airbag system is triggered inthe event of a front-end impact ofa certain severity. The ignition needsto be switched on.

46 Seats, restraints

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and head ofthe front seat occupantsconsiderably.

9 Warning

Optimum protection is onlyprovided when the seat is in theproper position 3 33.Keep the area in which the airbaginflates clear of obstructions.Fit the seat belt correctly andengage securely. Only then theairbag is able to protect.

Side airbag system

The side airbag system consists of anairbag in each front seat backrest.This can be identified by the wordAIRBAG.The side airbag system is triggered inthe event of a side impact of a certainseverity. The ignition needs to beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and pelvis inthe event of a side-on collisionconsiderably.

Seats, restraints 47

9 Warning

Keep the area in which the airbaginflates clear of obstructions.

NoteOnly use protective seat covers thathave been approved for the vehicle.Be careful not to cover the airbags.

Curtain airbag systemThe curtain airbag system consists ofan airbag in the roof frame on eachside. This can be identified by theword AIRBAG on the roof pillars.The curtain airbag system is triggeredin the event of a side-on impact ofa certain severity. The ignition needsto be switched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the head in the event ofa side-on impact considerably.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.The hooks in the roof frame areonly suitable for hanging up lightarticles of clothing, without coathangers. Do not keep any items inthese clothes.

Airbag deactivationThe front passenger airbag systemhas to be deactivated if a childrestraint system is to be fitted on thisseat. The side airbag and curtainairbag systems, the belt tensionersand all driver airbag systems willremain active.

The front passenger airbag systemcan be deactivated via a key-operated switch on the right side ofthe instrument panel.

48 Seats, restraints

Use the ignition key to choose theposition:* = front passenger airbag is

deactivated and will not inflatein the event of a collision.Control indicator * illuminatescontinuously. A child restraintsystem can be installed inaccordance with thechart Child restraintinstallation locations 3 50.No adult person is allowed tooccupy the front passengerseat.

V = front passenger airbag isactive. A child restraint systemmust not be installed.

9 Danger

Risk of fatal injury for a child usinga child restraint system on a seatwith activated front passengerairbag.Risk of fatal injury for an adultperson on a seat with deactivatedfront passenger airbag.

As long as the control indicator * isnot illuminated, the front passengerairbag system will inflate in the eventof a collision.If both control indicators areilluminated at the same time, there isa system failure. The status of thesystem is not discernible, thereforeno person is allowed to occupy thefront passenger seat. Contacta workshop immediately.Consult a workshop immediately ifnone of the two control indicators isilluminated.Change status only when the vehicleis stopped with the ignition off.

Status remains until the next change.Control indicator for airbagdeactivation 3 86.

Seats, restraints 49

Child restraintsChild restraint systemsWe recommend the Vauxhall childrestraint system which is tailoredspecifically to the vehicle.When a child restraint system is beingused, pay attention to the followingusage and installation instructionsand also those supplied with the childrestraint system.Always comply with local or nationalregulations. In some countries, theuse of child restraint systems isforbidden on certain seats.

9 Warning

When using a child restraintsystem on the front passengerseat, the airbag systems for thefront passenger seat must bedeactivated; if not, the triggering ofthe airbags poses a risk of fatalinjury to the child.This is especially the case if rear-facing child restraint systems areused on the front passenger seat.

Selecting the right systemThe rear seats are the mostconvenient location to fasten a childrestraint system.Children should travel facingrearwards in the vehicle as long aspossible. This makes sure that thechild's backbone, which is still veryweak, is under less strain in the eventof an accident.Children under the age of 12 yearsthat are smaller than 5 ft are onlyallowed to travel in a restraint systemthat is suitable for the child. Suitableare restraint systems that comply with

ECE 44-03 or ECE 44-04. Sincea proper position of the belt is rarelypossible with a child that is smallerthan 5 ft, we strongly advise to use anappropriate child restraint system,even though this might due to the ageof the child no longer be legallybinding.Ensure that the child restraint systemto be installed is compatible with thevehicle type.Ensure that the mounting location ofthe child restraint system within thevehicle is correct.Allow children to enter and exit thevehicle only on the side facing awayfrom the traffic.When the child restraint system is notin use, secure the seat with a seat beltor remove it from the vehicle.NoteDo not stick anything on the childrestraint systems and do not coverthem with any other materials.A child restraint system which hasbeen subjected to stress in anaccident must be replaced.

50 Seats, restraints

Child restraint installation locationsPermissible options for fitting a child restraint system

Weight and age classOn front passenger seat

On rear outboard seats On rear centre seatactivated airbag deactivated airbag

Group 0: up to 10 kgor approx. 10 months

X U1 U2, 4 U3

Group 0+: up to 13 kgor approx. 2 years

X U1 U2, 4 U3

Group I: 9 to 18 kgor approx. 8 months to 4 years

X U1 U2, 4 U3

Group II: 15 to 25 kgor approx. 3 to 7 years

X X U4 U3

Group III: 22 to 36 kgor approx. 6 to 12 years

X X U4 U3

Seats, restraints 51

1 = Only if front passenger seat airbag system is deactivated. If the child restraint system is being secured using a three-point seat belt, move seat height adjustment to uppermost position and ensure that vehicle seat belt runs forwardsfrom the upper anchorage point.

2 = Seat available with ISOFIX and Top-Tether mounting brackets.3 = Only if outboard seats are flush with the centre seat (position 2, 3 38).4 = Only if outboard seats are in position 1 or 2, 3 38.U = Universal suitability in conjunction with three-point seat belt.X = No child restraint system permitted in this weight and age class.

Permissible options for fitting an ISOFIX child restraint systemWeight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat

Group 0: up to 10 kg E ISO/R1 X IL X

Group 0+: up to 13 kg E ISO/R1 X IL X

D ISO/R2 X IL X

C ISO/R3 X IL X

Group I: 9 to 18 kg D ISO/R2 X IL X

C ISO/R3 X IL X

B ISO/F2 X IL, IUF X

B1 ISO/F2X X IL, IUF X

A ISO/F3 X IL, IUF X

52 Seats, restraints

IL = Suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories.The ISOFIX restraint system must be approved for the specific vehicle type.

IUF = Suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weightclass.

X = No ISOFIX child restraint system approved in this weight class.

ISOFIX size class and seat deviceA – ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg.B – ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.B1 – ISO/F2X = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.C – ISO/R3 = Rear-facing child restraint system for children of maximum size in the weight class up to 13 kg.D – ISO/R2 = Rear-facing child restraint system for smaller children in the weight class up to 13 kg.E – ISO/R1 = Rear-facing child restraint system for young children in the weight class up to 13 kg.

Seats, restraints 53

ISOFIX child restraint systems

Fasten vehicle-approved ISOFIXchild restraint systems to the ISOFIXmounting brackets. Specific vehicleISOFIX child restraint systempositions are marked in the table byIL.ISOFIX mounting brackets areindicated by a label on the backrest.

Top-tether fastening eyesTop-tether fastening eyes are markedwith the symbol : for a child seat.

In addition to the ISOFIX mounting,fasten the Top-tether strap to theTop-tether fastening eyes. The strapmust run between the two guide rodsof the head restraint.ISOFIX child restraint systems ofuniversal category positions aremarked in the table by IUF.

54 Storage

Storage

Storage compartments ................ 54Load compartment ....................... 66Roof rack system ......................... 71Loading information ..................... 72

Storage compartmentsGlovebox

The glovebox features a pen holderand a coin holder.Inside the glovebox there isa compartment for the Owner'sManual. Pull the lug to open thecompartment.The glovebox should be closed whilstdriving.

Cupholders

Cupholders are located in the centreconsole.

Detachable cupholderA cupholder can be attached either tothe upper or lower guide rails in thefront console.

Storage 55

Fold the frame out of initial positionbefore using.NoteIf the cupholder is installed in thelower guide rail and the detachablearmrest in the upper guide rail, makesure that the frame is folded backinto the initial position before movingone of the parts. Otherwise thearmrest and the cupholder might bedamaged while moving them oneabove the other.

Armrest 3 36.

Installing cupholder

Press the buttons at the front and therear and insert the guide pins into theupper or lower guide rails. The frontbutton has to be pressed firmly.Release the buttons and move thecupholder until it engages audibly.

Moving cupholder

Press the front button slightly andmove the cupholder to the desiredposition. Release the button andmove the cupholder until it engagesaudibly.

Removing cupholderPress the buttons at the front and therear and remove the cupholder. Thefront button has to be pressed firmly.The cupholder can also be installedon the folded centre rear seat 3 40.

56 Storage

Front storage

A storage compartment is locatednext to the steering wheel.

Sunglasses storage

Fold down and open.Do not use for storing heavy objects.

Underseat storage

Pull handle to disengage and pull outthe drawer. Maximum load: 3 kg. Toclose, push the drawer in andengage.

Storage 57

Armrest storageStorage in the detachable armrest

Pull handle and fold the armrest lidupwards. The armrest containsa storage compartment.The armrest can also be installed onthe folded centre rear seat 3 40.

Rear carrier system

The rear carrier system (Flex-Fixsystem) allows bicycles to beattached to a pull-out carrierintegrated into the vehicle floor.The maximum load is 40 kg.If not in use, the carrier system can beslid back into the vehicle floor.A multifunction box is offered as anaccessory for the rear carrier system.The transportation of other objects isnot permitted.There must not be any objects on thebicycles that could become looseduring transportation.

ExtendingOpen the tailgate.

9 Warning

No persons may remain in theextension zone of the rear carriersystem, risk of injury.

Pull release lever up. The systemdisengages and travels quickly out ofthe bumper.

58 Storage

Completely pull out the rear carriersystem until you hear it engage.Ensure that it is not possible to pushin the rear carrier system withoutpulling the release lever again

9 Warning

It is only permissible to fit objectsto the rear carrier system if thesystem has been correctlyengaged. If the rear carrier systemwill not engage correctly, do not fitobjects to the system and slide thesystem back. Seek the assistanceof a workshop.

Install the tail lamps

First remove the rear (1), then thefront (2) tail lamp from the recesses.

Open out the bulb holder on the backof the tail lamp completely.

Push the clamping lever down andpush the bulb holder into the retaineruntil it hits the stop.Perform this procedure for both taillamps.

Storage 59

Check the cable and lamp position tomake sure these are correctlyinstalled and are securely located.

Lock the rear carrier system

Swivel the left clamping lever (1) backfirst, followed by the right clampinglever (2) until they stop. Bothclamping levers must pointbackwards, otherwise safefunctionality is not guaranteed.NoteClose the tailgate!

Unfold the number licence plateholder

Unfold the holder for the numberlicence plate and fix the numberlicence plate.

60 Storage

Unfold pedal crank recesses

Fold one or both pedal crankrecesses upwards until the diagonalsupport engages.

Remove the pedal crank mounts fromthe pedal crank recesses.

Adapting the rear carrier systemto a bicycle

Press the release lever and withdrawthe wheel recesses.

Storage 61

Push the release lever on the strapretainer and remove the strapretainer.

Prepare the bicycle forattachment

Rotate the left pedal (without a chaincog) vertically downwards. The pedalon the left pedal crank must behorizontal.The front bicycle must have its frontwheel facing left.The rear bicycle must have its frontwheel facing right.

Attaching a bicycle to the rearcarrier system

With the rotary lever on the pedalcrank recess, roughly adapt theadjustable pedal crank unit to theprotrusion of the pedal crank.If the bicycle has straight pedalcranks, unscrew the pedal crank unitcompletely (position 5).

62 Storage

If the bicycle has curved pedalcranks, screw in the pedal crank unitall the way (position 1).

Put on the bicycle. The pedal crankhere must be placed in the pedalcrank recess opening as shown in theillustration.

Caution

Make sure that the pedal does nottouch the surface of the rear endcarrier. Otherwise the bottombracket might be damaged duringthe transport.

Insert pedal crank mount into outerrail of each pedal crank recess fromabove and slide downwards till atleast underneath the notching.

Attach the pedal crank by rotating theattachment screw on the pedal crankmount.

Storage 63

Place the wheel recesses such thatthe bicycle is more or less horizontal.Here, the distance between thepedals and the tailgate should be atleast 2 inches.Both bicycle tyres must be in thewheel recesses. In order to preventdamage, neither the pedal bearinghousing on the bicycle nor the pedalcrank is allowed to be touching thepedal crank recess.

Align the bicycle in the longitudinaldirection of the vehicle: Slightlyloosen the pedal mount.

Place the bicycle upright using therotary lever on the pedal crankrecess.If the two bicycles obstruct oneanother, the relative positions of thebicycles can be adapted by adjustingthe wheel recesses and the rotarylever on the pedal crank recess untilthe bicycles no longer touch oneanother. Make sure there is sufficientclearance from the vehicle.

Tighten the attachment screw for thepedal bearing mount to its maximumpoint.

Secure both bicycle wheels to wheelrecesses using strap retainers.Check the bicycle to make sure it issecure.The settings for the wheel recessesand on the rotary lever on the pedalcrank recess should be noted andsaved for each bicycle. Correctpresetting will facilitate refitting of thebicycle.

Removing a bicycle from the rearcarrier system

Undo strap retainers on both bicycletyres.

64 Storage

Hold on to the bicycle, loosen theattachment screw for the pedalbearing mount, then lift the pedalbearing mount to remove it.

Retracting the rear carrier system

Push the pedal crank mounts into thepedal crank recess.

Insert the strap retainer and pulltightly downwards as far as possible.

Press release lever and slide in wheelrecesses all the way as far as they willgo.

Disengage the locking lever on thediagonal support and fold both pedalcrank recesses down.

9 Warning

Risk of pinching.

Remove number licence plate andfold down the number licence plateholder.

Storage 65

Swivel first the right clamping lever(1) forwards, followed by the leftclamping lever (2), until they can beengaged in their respective recesses.

Push the clamping lever down andpull both lamp supports out of therecesses.

Fold in the bulb holders on the backsof the tail lamps.First place the front (1) tail lamp, thenthe rear (2) tail lamp in the recessesand push down as far as possible.Push cables all the way into all guidesin order to prevent damage.

Open the tailgate.Push the release lever up and pushthe system into the bumper until itengages.Release lever must return to originalposition.

9 Warning

If the system cannot be correctlyengaged, please seek theassistance of a workshop.

66 Storage

Load compartment

Folding down rear seat backrestsThe rear seat backrest is divided intothree parts. All parts can be foldeddown and lowered individually toincrease the size of the loadcompartment.

9 Warning

Do not stow objects under orbehind the seats. The objectsmight be damaged and preventthe guide rails from lockingproperly.

A completely flat load bay is createdif the rear seat backrests are foldeddown.

Caution

Do not fold the outer seatbackswhile the seats are in the innerposition. The seats could bedamaged.

Remove the load compartment coverif necessary 3 67.Push head restraints down bypressing both catches.

Take the seat belt out of the retainingclip on the backrest.

Pull the strap on the front side of thebackrest and fold down the backrestonto the seat cushion. The seat islowered automatically.The backrests can also be foldedfrom the load compartment.

Storage 67

Pull the strap on the back side of thebackrest and fold down the backrest.To fold up, pull the strap and raise thebackrests into an upright position untilthey engage audibly.

9 Warning

Only drive the vehicle if thebackrests are securely locked intoposition. Otherwise there is a riskof personal injury or damage to theload or vehicle in the event ofheavy braking or a collision.

Rear storageOn the left side of the loadcompartment there is a stowagecompartment.

Turn the fastener anticlockwise andfold down the cover.

Load compartment coverDo not place any objects on the cover.

Removing the cover

Unhook retaining straps from tailgate.

68 Storage

Lift cover at the rear and pull it fromthe side guides.

Stowing the cover

The cover can be stowed behind therear seats.

Fitting the coverEngage cover in side guides and folddownwards. Attach retaining straps totailgate.

Rear floor storage cover

The rear floor cover can be lifted.Pull out the hook at the left sidewall ofthe load compartment to hold thecover upright.

Double load-bay floorThe double load-bay floor can beinserted in the load compartment intwo positions:■ directly beneath the cover for the

spare wheel recess or the floorcover,

■ or in the upper openings in the loadcompartment.

To remove, lift the load-bay floorusing the lever and pull backwards.To insert, push the load-bay floorforwards in the corresponding guide,then lower.

If mounted in the upper position, thespace between the load-bay floor andthe spare wheel well cover can beused as a stowage compartment.In this position, if the rear seatbackrests are folded forwards, analmost completely flat load bay iscreated.

Storage 69

The double load-bay floor is able towithstand a load of no more than100 kg.In models with a tyre repair kit, thespare wheel recess may be used asan additional stowage compartment.

Lashing eyes

The lashing eyes are designed tosecure items against slippage, e.g.using lashing straps or luggage net.

Safety netThe safety net can be installed behindthe front seats.

Passengers must not be transportedbehind the safety net.

Installation

There are two installation openings inthe roof frame: suspend rod of net atone side, push to the front andengage. Extend rod, suspend at otherside, push to the front and engage.

Suspend hooks of net tensioningbelts in lashing eyes in the floorbehind the front seats. Tension thenet by pulling the loose end of the belt.Suspend and tighten on both sides.

RemovalTilt length adjuster of the nettensioning belts upwards and detachthe belts on both sides. Disengagethe upper rod on one side, disengageother side and remove from theopenings.

70 Storage

Stowage

Place tensioning straps as shown infigure and align to net.

Roll the upper net rod down toapproximately over the middle.Place the upper net rod over thetensioning straps next to the lower netrod. The hooks on the upper net rodmust point away from the lower netrod.

Fasten Velcro tape tightly about thenet next to the length adjusters. Thelength adjusters and net rods must lieflat next to each other.Stow safety net in the space betweenthe double load-bay floor in the loadcompartment. Rear floor storagecover 3 68

Folding trayLocated in the front seat backrests.Open by pulling upward until itengages.Fold away by pressing down past theresistance point.Do not place any heavy objects.

Warning triangle

Stow the warning triangle in the spaceat the rear side of the loadcompartment.

Storage 71

First aid kit

Stow the first aid kit and the highvisibility vest under the driver's seatusing the straps.

Depending on the vehicle, a box islocated under the driver's seat. Pullhandle and fold down the cover.Maximum load: 1,5 kg.

Roof rack systemRoof rackFor safety reasons and to avoiddamage to the roof, the vehicleapproved roof rack system isrecommended.Follow the installation instructionsand remove the roof rack when not inuse.

Detach the cover from each mountingpoint.

72 Storage

Loading information

■ Heavy objects in the loadcompartment should be placedagainst the seat backrests. Ensurethat the backrests are securelyengaged. If objects can be stacked,heavier objects should be placed atthe bottom.

■ Secure objects with lashing strapsattached to the lashing eyes 3 69.

■ Use the hook at the left sidewall ofthe load compartment for hangingup carrier bags. Pull out the hook.Maximum load: 3 kg.

■ Secure loose objects in the loadcompartment to prevent them fromsliding.

■ When transporting objects in theload compartment, the backrests ofthe rear seats must not be angledforward.

■ Do not allow the load to protrudeabove the upper edge of thebackrests.

■ Do not place any objects on theload compartment cover or theinstrument panel, and do not coverthe sensor on top of the instrumentpanel.

■ The load must not obstruct theoperation of the pedals, parkingbrake and gear selector, or hinderthe freedom of movement of thedriver. Do not place any unsecuredobjects in the interior.

■ Do not drive with an open loadcompartment.

9 Warning

Always make sure that the load inthe vehicle is securely stowed.Otherwise objects can be thrownaround inside the vehicle andcause personal injury or damageto the load or car.

■ The payload is the differencebetween the permitted grossvehicle weight (see identification

Storage 73

plate 3 184) and the EC kerbweight.To calculate the payload, enter thedata for your vehicle in the Weightstable at the front of this manual.The EC kerb weight includesweights for the driver (68 kg),luggage (7 kg) and all fluids (tank90 % full).Optional equipment andaccessories increase the kerbweight.

■ Driving with a roof load increasesthe sensitivity of the vehicle tocross-winds and has a detrimentaleffect on vehicle handling due tothe vehicle's higher centre ofgravity. Distribute the load evenlyand secure it properly with retainingstraps. Adjust the tyre pressure andvehicle speed according to the loadconditions. Check and retighten thestraps frequently.The permissible roof load is 60 kg.The roof load is the combinedweight of the roof rack and the load.

74 Instruments and controls

Instruments andcontrols

Controls ....................................... 74Warning lights, gauges andindicators ..................................... 80Information displays ..................... 90Vehicle messages ........................ 94Trip computer ............................... 98Vehicle personalisation ................ 99

ControlsSteering wheel adjustment

Unlock lever, adjust steering wheel,then engage lever and ensure it isfully locked.Do not adjust steering wheel unlessvehicle is stationary and steeringwheel lock has been released.

Steering wheel controls

The Infotainment system, the cruisecontrol and a connected mobilephone can be operated via thecontrols on the steering wheel.Further information is available in theInfotainment system manual.Cruise control 3 133.

Instruments and controls 75

Heated steering wheel

Activate heating by pressing *button. Activation is indicated by theLED in the button.

The recommended grip areas of thesteering wheel are heated quickerand to a higher temperature than theother areas.

Horn

Press j.

76 Instruments and controls

Windscreen wiper/washerWindscreen wiper

2 = fast1 = slowP = interval wiping§ = off

For a single wipe when thewindscreen wiper is off, press thelever down.Do not use if the windscreen is frozen.Switch off in car washes.

Adjustable wiper interval

Wiper lever in position P.Turn the adjuster wheel to adjust thedesired wipe interval:shortinterval

= turn adjuster wheelupwards

longinterval

= turn adjuster wheeldownwards

Automatic wiping with rain sensor

P = automatic wiping with rainsensor

The rain sensor detects the amount ofwater on the windscreen andautomatically regulates the frequencyof the windscreen wiper.

Instruments and controls 77

Adjustable sensitivity of the rainsensor

Turn the adjuster wheel to adjust thesensitivity:lowsensitivity

= turn adjuster wheeldownwards

highsensitivity

= turn adjuster wheelupwards

Keep the sensor free from dust, dirtand ice.

Windscreen washer

Pull lever. Washer fluid is sprayedonto the windscreen and the wiperwipes a few times.

Rear window wiper/washer

Push the rocker switch to activate therear window wiper:upper position = short intervallower position = long intervalmiddle position = off

78 Instruments and controls

Push lever. Washer fluid is sprayedonto the rear window and the wiperwipes a few times.Do not use if the windscreen is frozen.Switch off in car washes.The rear window wiper comes onautomatically when the windscreenwiper is switched on and reverse gearis engaged.Activation or deactivation of thisfunction can be changed in the menuSettings in the Info-Display.Vehicle personalisation 3 99.

Outside temperature

A drop in temperature is indicatedimmediately and a rise in temperatureafter a time delay.If outside temperature drops to 3 °C,the symbol 4 illuminates in the DriverInformation Center withUplevel-Display or in theInfo-Display as a warning for icy roadconditions. 4 remains illuminateduntil temperatures reach at least5 °C.

Additionally a warning message isdisplayed in the Driver InformationCenter with Uplevel-Display.

9 Warning

The road surface may already beicy even though the displayindicates a few degrees above0 °C.

ClockDate and time are shown in theInfo-Display.

Instruments and controls 79

Set date and timePress the CONFIG button. The menuSettings is displayed.Select Time & Date.

Selectable setting options:■ Set time: Changes the time shown

on the display.■ Set date: Changes the date shown

on the display.■ Set time format: Changes

indication of hours between 12hours and 24 hours.

■ Set date format: Changesindication of date between MM/DD/YYYY and DD.MM.YYYY.

■ Display digital clock: Switches on/off indication of time on the display.

■ RDS clock synchronization: TheRDS signal of most VHFtransmitters automatically sets thetime. RDS time synchronisationcan take a few minutes. Sometransmitters do not send a correcttime signal. In such cases, it isrecommended to switch offautomatic time synchronisation.

Vehicle personalisation 3 99.

Power outlets

A 12 volts power outlet is located inthe front console.

80 Instruments and controls

A further 12 volts power outlet islocated in the rear console.Do not exceed the maximum powerconsumption of 120 watts.With ignition off, the power outlets aredeactivated. Additionally the poweroutlets are deactivated in the event oflow battery voltage.Electrical accessories that areconnected must comply with theelectromagnetic compatibilityrequirements laid down inDIN VDE 40 839.Do not connect any current-deliveringaccessories, e.g. electrical chargingdevices or batteries.Do not damage the outlet by usingunsuitable plugs.

Warning lights, gaugesand indicatorsSpeedometer

Indicates vehicle speed.

Odometer

The bottom line displays the recordeddistance.

Trip odometerThe top line displays the recordeddistance since the last reset.To reset, hold the reset knobdepressed for a few seconds with theignition on.

Instruments and controls 81

Tachometer

Displays the engine speed.Drive in a low engine speed range foreach gear as much as possible.

Caution

If the needle is in the red warningzone, the maximum permittedengine speed is exceeded. Engineat risk.

Fuel gauge

Displays the fuel level in the tank.Control indicator i illuminates if thelevel in the tank is low. Refuelimmediately.Never run the tank dry.Because of the fuel remaining in thetank, the top-up quantity may be lessthan the specified tank capacity.

Engine coolant temperaturegauge

Displays the coolant temperature.left area = engine operating

temperature not yetreached

centralarea

= normal operatingtemperature

right area = temperature too high

82 Instruments and controls

Caution

If engine coolant temperature istoo high, stop vehicle, switch offengine. Danger to engine. Checkcoolant level.

Service displayThe engine oil life system lets youknow when to change the engine oiland filter. Based on drivingconditions, the interval at which anengine oil and filter change will beindicated can vary considerably.

In the Uplevel-Display the remainingoil life duration is displayed in theVehicle Information Menu.In the Midlevel-Display the remainingengine oil life duration is displayed bythe control indicator I. The ignitionmust be switched on, with the enginenot running.The menu and function can beselected via the buttons on the turnsignal lever.To display the remaining engine oillife duration:

Press the MENU button to select theVehicle Information Menu.

Turn the adjuster wheel to selectRemaining Oil Life.The system must be reset every timethe engine oil is changed to allowproper functionality. Seek theassistance of a workshop.Press the SET/CLR button to resetwhile applying the brake pedal. Theignition must be switched on, with theengine not running.When the system has calculated thatengine oil life has been diminished,Change Engine Oil Soon or a warningcode appears in the DriverInformation Center. Have engine oiland filter changed by a workshopwithin one week or 300 miles(whichever occurs first).Driver Information Center 3 90.Service information 3 180.

Control indicatorsThe control indicators described arenot present in all vehicles. Thedescription applies to all instrumentversions.

Instruments and controls 83

Depending on the equipment theposition of the control indicators mayvary.When the ignition is switched on,most control indicators will illuminatebriefly as a functionality test.The control indicator colours mean:red = danger, important

reminderyellow = warning, information, faultgreen = confirmation of activationblue = confirmation of activationwhite = confirmation of activation

84 Instruments and controls

Control indicators in the instrument cluster

Instruments and controls 85

Control indicators in the centreconsole

Turn signalO illuminates or flashes green.

Illuminates brieflyThe parking lights are switched on.

FlashesA turn signal or the hazard warningflashers are activated.Rapid flashing: failure of a turn signallight or associated fuse, failure of turnsignal light on trailer.

Bulb replacement 3 147, Fuses3 156.Turn signals 3 109.

Seat belt reminderSeat belt reminder on driver seatX for seat illuminates or flashes red.

IlluminatesAfter the ignition has been switchedon until the seat belt has beenfastened.

FlashesAfter having started the engine fora maximum of 100 seconds until theseat belt has been fastened.Fastening the seat belt 3 42.

Seat belt status on rear seats> or X in the Driver InformationCenter flashes or illuminates.

IlluminatesAfter the ignition has been switchedon for a minimum of 35 seconds untilthe seat belt has been fastened.

FlashesAfter starting off when the seat belt isunfastened.Fastening the seat belt 3 42.

Airbag and belt tensionersv illuminates red.When the ignition is switched on, thecontrol indicator illuminates forapprox. 4 seconds. If it does notilluminate, does not go out after4 seconds or illuminates whilstdriving, there is a fault in the airbagsystem. Seek the assistance ofa workshop. The airbags and beltpretensioners may fail to trigger in theevent of an accident.Deployment of the belt pretensionersor airbags is indicated by continuousillumination of v.

86 Instruments and controls

9 Warning

Have the cause of the faultremedied immediately bya workshop.

Belt pretensioners, airbag system3 41, 3 45.

Airbag deactivationV illuminates yellow.The front passenger airbag isactivated.* illuminates yellow.The front passenger airbag isdeactivated 3 47.

9 Danger

Risk of fatal injury for a child usinga child restraint system togetherwith activated front passengerairbag.Risk of fatal injury for an adultperson with deactivated frontpassenger airbag.

Charging systemp illuminates red.Illuminates when the ignition isswitched on and goes out shortly afterthe engine starts.

Illuminates when the engine isrunningStop, switch off engine. Battery is notcharging. Engine cooling may beinterrupted. The brake servo unit maycease to be effective. Seek theassistance of a workshop.

Malfunction indicator lightZ illuminates or flashes yellow.Illuminates when the ignition isswitched on and goes out shortly afterthe engine starts.

Illuminates when the engine isrunningFault in the emission control system.The permitted emission limits may beexceeded. Seek the assistance ofa workshop immediately.

Flashes when the engine isrunningFault that could lead to catalyticconverter damage. Ease up on theaccelerator until the flashing stops.Seek the assistance of a workshopimmediately.

Service vehicle soong illuminates yellow.Additionally a warning message ora warning code is displayed.The vehicle needs a service.Seek the assistance of a workshop.Vehicle messages 3 94.

Brake and clutch systemBrake and clutch fluid level& illuminates red.The brake and clutch fluid level is toolow 3 145.

Instruments and controls 87

9 Warning

Stop. Do not continue yourjourney. Consult a workshop.

Operate pedal- illuminates or flashes yellow.

IlluminatesBrake pedal needs to be operated torelease the electrical parking brake3 130.

FlashesClutch pedal needs to be operated tostart the engine 3 122.

Electrical parking brakem illuminates or flashes red.

IlluminatesElectrical parking brake is applied3 130.

FlashesElectrical parking brake is not fullyapplied or released. Switch onignition, depress brake pedal andattempt to reset the system by firstreleasing and then applying theelectrical parking brake. If m remainsflashing, do not drive and seek theassistance of a workshop.

Electrical parking brake faultj illuminates or flashes yellow.

IlluminatesElectrical parking brake is operatingwith degraded performance 3 130.

FlashesElectrical parking brake is in servicemode. Stop vehicle, apply andrelease the electrical parking brake toreset.

9 Warning

Have the cause of the faultremedied immediately bya workshop.

Antilock brake system (ABS)u illuminates yellow.Illuminates for a few seconds after theignition is switched on. The system isready for operation when the controlindicator goes out.If the control indicator does not go outafter a few seconds, or if it illuminateswhile driving, there is a fault in theABS. The brake system remainsoperational but without ABSregulation.Antilock brake system 3 129.

Upshift[ illuminates green.Upshifting is recommended for fuelsaving.

Variable effort steeringc illuminates yellow.Fault in variable effort steeringsystem. This may lead to a higher orlower steering effort. Consulta workshop.

88 Instruments and controls

Ultrasonic parking assistr illuminates yellow.Fault in systemorFault due to sensors that are dirty orcovered by ice or snoworInterference due to external sourcesof ultrasound. Once the source ofinterference is removed, the systemwill operate normally.Have the cause of the fault in thesystem remedied by a workshop.Ultrasonic parking assist 3 134.

Electronic Stability Control offn illuminates yellow.The system is deactivated.

Electronic Stability Control andTraction Control systemb illuminates or flashes yellow.

IlluminatesA fault in the system is present.Continued driving is possible. Drivingstability, however, may deterioratedepending on road surfaceconditions.Have the cause of the fault remediedby a workshop.

FlashesThe system is actively engaged.Engine output may be reduced andthe vehicle may be brakedautomatically to a small degree.Electronic stability control 3 132,Traction control system 3 131.

Traction Control system offk illuminates yellow.The system is deactivated.

Preheating! illuminates yellow.Preheating is activated. Onlyactivates when outside temperatureis low.

Diesel particle filter% illuminates or flashes yellow.The diesel particle filter requirescleaning.Continue driving until % goes out. Ifpossible do not allow engine speed todrop below 2000 rpm.

IlluminatesThe diesel particle filter is full. Startcleaning process as soon aspossible.

FlashesThe maximum filling level of the filteris reached. Start cleaning processimmediately to avoid damage to theengine.Diesel particle filter 3 123.

Deflation detection systemw illuminates or flashes yellow.

IlluminatesDeflation detected. Stop immediatelyand check tyre pressure.

Instruments and controls 89

FlashesFault in system. Consult a workshop.Deflation detection system 3 164.

Engine oil pressureI illuminates red.Illuminates when the ignition isswitched on and goes out shortly afterthe engine starts.

Illuminates when the engine isrunning

Caution

Engine lubrication may beinterrupted. This may result indamage to the engine and/orlocking of the drive wheels.

1. Depress clutch.2. Select neutral gear, set selector

lever to N.3. Move out of the flow of traffic as

quickly as possible withoutimpeding other vehicles.

4. Switch off ignition.

9 Warning

When the engine is off,considerably more force is neededto brake and steer.Do not remove key until vehicle isstationary, otherwise the steeringwheel lock could engageunexpectedly.

Check oil level before seekingassistance of a workshop 3 143.

Low fueli illuminates yellow.Level in fuel tank is too low.Catalytic converter 3 124.Bleeding the diesel fuel system3 146.

Immobiliserd flashes yellow.Fault in the immobiliser system. Theengine cannot be started.

Reduced engine power# illuminates yellow.The engine power is limited. Consulta workshop.

Exterior light8 illuminates green.The exterior lights are on 3 105.l illuminates green.The automatic light control isswitched on 3 105.

High beamC illuminates blue.Illuminated when high beam is on andduring headlight flash 3 106.

Adaptive forward lightingf illuminates or flashes yellow.

IlluminatesFault in system.Seek the assistance of a workshop.

90 Instruments and controls

FlashesSystem switched to symmetrical lowbeam.Control indicator f flashes for approx.4 seconds after the ignition isswitched on as a reminder that thesystem has been activated 3 107.Automatic light control 3 105.

Daytime running lightV illuminates green.The daytime running light is on.

Fog light> illuminates green.The front fog lights are on 3 109.

Rear fog lightr illuminates yellow.The rear fog light is on 3 109.

Cruise controlm illuminates white or green.

Illuminates whiteThe system is on.

Illuminates greenA certain speed is stored.Cruise control 3 133

Door openh illuminates red.A door or the tailgate is open.

Automatic locking^ illuminates amber.Fault in the automatic locking system.The rear doors are possibly notsecured against opening.

9 Warning

Stop your journey immediately!Follow the instructions asdescribed in paragraph "Fault inthe automatic locking system"before continuing your journey3 23.Consult a workshop.

Information displaysDriver Information Center

The Driver Information Center (DIC)is located in the instrument clusterbetween speedometer andtachometer. It is available asMidlevel- or Uplevel-Display.

Instruments and controls 91

The following main menus,depending on the vehicleconfiguration, can be selected:■ Vehicle Information Menu■ Trip/Fuel Information MenuSome of the displayed functions differbetween vehicle driving and standstilland some functions are only activewhen the vehicle is driving.Vehicle personalisation 3 99,Memorised settings 3 20.

Selecting menus and functionsThe menus and functions can beselected via the buttons on the turnsignal lever.

Press the MENU button to switchbetween the menus or to return froma submenu to the next higher menulevel.

Turn the adjuster wheel to highlighta menu option or to set a numericvalue.

Press the SET/CLR button to selecta function or to confirm a message.

Vehicle Information MenuPress the MENU button to select theVehicle Information Menu.Turn the adjuster wheel to select oneof the submenus. Press the SET/CLR button to confirm.

92 Instruments and controls

Follow the instructions given in thesubmenus.Possible submenus:■ Unit: Displayed units can be

changed.■ Remaining Oil Life: 3 82■ Speed Warning: If exceeding the

preset speed, a warning chime willbe activated.

■ Language: Displayed language canbe changed.

Selection and indication can bedifferent between Midlevel- andUplevel-Display.

Trip/Fuel Information Menu

Trip/Fuel Information Menu, TripComputer 3 98.

Graphic-Info-Display, Colour-Info-DisplayDepending on the vehicleconfiguration the vehicle hasa Graphic- or Colour-Info-Display.The Info-Display is located in theinstrument panel above theInfotainment system.

Graphic-Info-Display

Depending on the Infotainmentsystem, the Graphic-Info-Display isavailable in two versions.

Instruments and controls 93

Graphic-Info-Display indicates:■ time 3 78■ outside temperature 3 78■ date 3 78■ Infotainment system, see

description for Infotainment system■ settings for vehicle personalisation3 99

Colour-Info-Display

The Colour-Info-Display indicates incolour:■ time 3 78■ outside temperature 3 78■ date 3 78■ Infotainment system, see

description for Infotainment system■ navigation, see description for

Infotainment system■ system settings

■ vehicle messages 3 94■ settings for vehicle personalisation3 99

The type of information and how it isdisplayed depends on the equipmentof the vehicle and the settings made.

Selecting menus and settingsMenus and settings are accessed viathe display.

Selections are made via:■ menus■ function buttons and multifunction

knob of the Infotainment system

94 Instruments and controls

Selecting with the Infotainmentsystem

Select a function via the Infotainmentsystem buttons. The menu of theselected function is displayed.The multifunction knob is used toselect an item and to confirm.

Multifunction knobThe multifunction knob is the centralcontrol element for the menus:Turn■ To mark a menu option■ To set a numeric value or to display

a menu option

Press (the outer ring)■ To select or activate the marked

option■ To confirm a set value■ To switch a system function on/offBACK buttonPress button to:■ exit a menu without changing

settings■ return from a submenu to a higher

menu level■ delete the last character in

a character sequencePress and hold the button for a fewseconds to delete the entire entry.Vehicle personalisation 3 99,Memorised settings 3 20.

Vehicle messagesMessages are indicated mainly in theDriver Information Center (DIC), insome cases together with a warningand signal buzzer.

Press the SET/CLR button to confirma message.

Instruments and controls 95

Call up multiple messages one afteranother by pushing the MENU button.

Vehicle messages on theMidlevel-Display

The vehicle messages are displayedas code numbers.

No. Vehicle message

1 Change engine oil

2 No radio remote controldetected, depress clutch pedalfor a restart

3 Engine coolant level low

4 Air conditioning off

No. Vehicle message

5 Steering wheel is locked

6 Depress brake pedal to releaseelectrical parking brake

7 Turn steering wheel, switchignition off and then on

8 Switch ignition off and then on,repeat breath test

9 Turn steering wheel, startengine again

11 Brake pads worn

12 Vehicle overloaded

13 Compressor overheated

15 Centre high-mounted brakelight failure

16 Brake light failure

17 Headlight levelling malfunction

18 Left low beam failure

19 Rear fog light failure

96 Instruments and controls

No. Vehicle message

20 Right low beam failure

21 Left front sidelight failure

22 Right front sidelight failure

23 Reversing light failure

24 Number plate light failure

25 Left front turn signal failure

26 Left rear turn signal failure

27 Right front turn signal failure

28 Right rear turn signal failure

29 Check trailer brake light

30 Check trailer reversing light

31 Check left trailer turn signal

32 Check right trailer turn signal

33 Check trailer rear fog light

34 Check trailer rear light

35 Replace battery in radio remotecontrol

No. Vehicle message

48 Clean side blind zone alertsystem

50 Activated pedestrian protectionsystem, reset bonnet

51 Compass unavailable

53 Tighten gas cap

54 Water in diesel fuel filter

55 Diesel particle filter is full3 123

59 Open and then close driverwindow

60 Open and then close frontpassenger window

61 Open and then close rear leftwindow

62 Open and then close rear rightwindow

65 Theft attempted

66 Service theft alarm system

No. Vehicle message

67 Service steering wheel lock

68 Service power steering

69 Service suspension system

70 Service level control system

71 Service rear axle

74 Service AFL

75 Service air conditioning

76 Service side blind zone alertsystem

78 Service pedestrian protectionsystem

79 Top up engine oil

80 Change transmission fluid

81 Service transmission

82 Change engine oil soon

83 Service adaptive cruise control

Instruments and controls 97

No. Vehicle message

84 Engine power is reduced

95 Service airbag

Vehicle messages on theUplevel-Display

The vehicle messages are displayedas text. Follow the instructions givenin the messages.The system displays messagesregarding the following topics:■ Fluid levels■ Anti-theft alarm system

■ Brakes■ Drive systems■ Ride control systems■ Cruise control■ Object detection systems■ Lighting, bulb replacement■ Wiper/washer system■ Doors, windows■ Radio remote control■ Seat belts■ Airbag systems■ Engine and transmission■ Tyre pressure■ Diesel particle filter

Vehicle messages on theColour-Info-DisplaySome important messages appearadditionally in theColour-Info-Display. Press themultifunction knob to confirma message. Some messages onlypop up for a few seconds.

Warning chimesWhen starting the engine or whilstdriving■ If seat belt is not fastened.■ If a door or the tailgate is not fully

closed when starting off.■ If a certain speed is exceeded with

parking brake applied.■ If a programmed speed is

exceeded.■ If a warning message or a warning

code appears in the DriverInformation Center.

■ If the parking assist detects anobject.

■ If a fault in the automatic lockingsystem is detected.

When the vehicle is parked and/orthe driver's door is opened■ When the key is in the ignition

switch.■ With exterior lights on.

98 Instruments and controls

Trip computerThe menus and functions can beselected via the buttons on the turnsignal lever.

Press the MENU button to select theTrip/Fuel Information Menu.

Turn the adjuster wheel to select oneof the submenus:■ Trip odometer 1■ Trip odometer 2■ Range■ Average consumption■ Instantaneous consumption■ Average speed■ Digital speed

The information of the two tripcomputers can be reset separately,making it possible to display differenttrip distances.To reset, press the reset knob orpress the SET/CLR button for a fewseconds.

Instruments and controls 99

RangeRange is calculated from current fueltank content and currentconsumption. The display showsaverage values.After refuelling, the range is updatedautomatically after a brief delay.When the fuel level in the tank is low,a message appears in the DriverInformation Center and in theInfo-Display.Additionally the control indicator i inthe fuel gauge illuminates.

Average consumptionDisplay of average consumption. Themeasurement can be reset at anytime.To reset, press the SET/CLR buttonfor a few seconds.

Instantaneous consumptionDisplay of the instantaneousconsumption.

Average speedDisplay of average speed. Themeasurement can be reset at anytime.To reset, press the SET/CLR buttonfor a few seconds.

Digital speedDigital display of the instantaneousspeed.

Vehicle personalisationThe vehicle's behaviour can bepersonalised by changing the settingsin the Info-Display.Some of the personal settings fordifferent drivers can be memorisedindividually for each vehicle key.Memorised settings 3 20.Depending on vehicle equipment andcountry-specific regulations some ofthe functions described below mightnot be available.Some functions are only displayed oractive when the engine is running.

100 Instruments and controls

Personal settings in theGraphic-Info-Display

Press the CONFIG button. The menuSettings is displayed.

The following settings can beselected by turning and pushing themultifunction knob:■ Time Date■ Radio settings■ Phone settings■ Vehicle settings■ Restore factory settingsIn the corresponding submenus thefollowing settings can be changed:

Time DateSee Clock 3 78.

Radio settingsSee description for Infotainmentsystem.

Phone settingsSee description for Infotainmentsystem.

Instruments and controls 101

Vehicle settings

■ Climate and air qualityAuto fan speed: Modifies the fanregulation.Automatic air recirculation:Modifies AQS (Air Quality Sensor)sensitivity low / high.Climate control mode: Activate ordeactivate cooling.Auto rear demist: Automaticactivation of rear heated window.

■ Comfort settingsChime volume: Change the volumeof warning chimes.Personalization by driver: Activateor deactivate the personalisationfunction.Rear auto wipe in reverse: Activateor deactivate automatic switchingon of the rear window wiper whenreverse gear is engaged.

■ Park assist / Collision detectionPark assist: Activate or deactivatethe ultrasonic parking assist .

■ LanguagesSelection of the desired language.

■ Exterior ambient lightingDuration upon exit of vehicle:Activate or deactivate and changethe duration of exit lighting.Exterior lighting by unlocking:Activate or deactivate the welcomelighting.

■ Remote locking, unlocking, startingRemote door unlock: Change theconfiguration to unlock only thedriver's door or the whole vehiclewhilst unlocking.

■ Restore factory settingsRestore factory settings: Reset allsettings to the default settings.

102 Instruments and controls

Personal settings in theColour-Info-Display

Press the CONFIG button. The menuSettings is displayed.

The following settings can beselected by turning and pushing themultifunction knob:■ Time & Date■ Radio settings■ Phone settings■ Navigation settings■ Vehicle settings■ Display settings■ Restore factory settingsIn the corresponding submenus thefollowing settings can be changed:

Time & DateSee Clock 3 78.

Radio settingsSee description for Infotainmentsystem.

Phone settingsSee description for Infotainmentsystem.

Navigation settingsSee description for Infotainmentsystem.

Instruments and controls 103

Vehicle settings

■ Climate and air qualityAuto fan speed: Modifies the fanregulation.Automatic air recirculation:Modifies AQS (Air Quality Sensor)sensitivity low / high.Climate control mode: Activate ordeactivate cooling.Auto rear demist: Automaticactivation of rear heated window.

■ Comfort settingsChime volume: Change the volumeof warning chimes.Rear auto wipe in reverse: Activateor deactivate automatic switchingon of the rear window wiper whenreverse gear is engaged.

■ Park assist / Collision detectionPark assist: Activate or deactivatethe ultrasonic parking assist.

■ LanguagesSelection of the desired language.

■ Exterior ambient lightingDuration upon exit of vehicle:Activate or deactivate and changethe duration of exit lighting.Exterior lighting by unlocking:Activate or deactivate the welcomelighting.

■ Lock / Unlock / StartRemote door unlock: Change theconfiguration to unlock only thedriver's door or the whole vehiclewhilst unlocking.

■ Restore factory settingsRestore factory settings: Reset allsettings to the default settings.

Display settingsSelectable display settings:■ Day mode: Optimisation for

daylight conditions.■ Night mode: Optimisation for

darkness.

104 Instruments and controls

■ Automatic mode:Vehicles without light sensor:The display changes the modewhen the vehicle lights areswitched on/off.Vehicles with light sensor:The display changes the mode dueto the exterior lighting conditionsindependently from the vehiclelights.

Lighting 105

Lighting

Exterior lighting .......................... 105Interior lighting ........................... 110Lighting features ........................ 112

Exterior lightingLight switch

Turn light switch:AUTO = automatic light control:

Headlights are switchedon and off automaticallydepending on externallighting conditions.

m = activation or deactivationof the automatic lightcontrol. Switch turns backto AUTO.

7 = off8 = sidelights9 = headlights

In the Driver Information Center withUplevel-Display, the current status ofthe automatic light control isdisplayed.When switching on the ignition,automatic light control is active.Control indicator 8 3 89, Automaticlight control indicator l 3 89.

Tail lightsTail lights are illuminated togetherwith headlights and sidelights.

Automatic light control

106 Lighting

Automatic light control functionWhen the automatic light controlfunction is switched on and theengine is running, the systemswitches between daytime runninglight and automatic headlightdepending on lighting conditions.

Daytime running lightDaytime running light increasesvisibility of the vehicle during daylight.In some countries also the tail lightsare on.

Automatic headlight activationDuring poor lighting conditions theheadlights are switched on.

Tunnel detectionWhen a tunnel is entered theheadlights are switched on withoutdelay.Adaptive forward lighting 3 108.

High beam

To switch from low to high beam,push lever.To switch to low beam, push leveragain or pull.

Headlight flashTo activate the headlight flash, pulllever.

Headlight range adjustmentManual headlight rangeadjustment

To adapt headlight range to thevehicle load to prevent dazzling: turnthumb wheel ? to required position.0 = front seats occupied1 = all seats occupied2 = all seats occupied and load

compartment laden3 = driver's seat occupied and load

compartment laden.

Lighting 107

Headlights when drivingabroadThe asymmetrical headlight beamextends visibility at the edge of theroad at the passenger side.However, when driving in countrieswhere traffic drives on the oppositeside of the road, adjust the headlightsto prevent dazzling of oncomingtraffic.

Vehicles without AdaptiveForward Lighting

Turn the adjusting screws with thescrewdriver clockwise for half a turn.

The adjusting screws are located atthe headlights above the low beamcaps 3 147.For deactivation turn the adjustingscrews anticlockwise for half a turn.

Caution

Have the adjustment of theheadlights checked afterdeactivation.We recommend to consulta workshop.

Vehicles with Adaptive ForwardLightingAdapting the aim of the headlightbeam:

Adapting the distribution of theheadlight beam:1. Pull turn signal lever.2. Switch on ignition.3. Hold turn signal lever. After

approx. 5 seconds the controlindicator f starts flashing and anacoustic signal sounds.

Control indicator f 3 89.Every time the ignition is switched on,f flashes as a reminder for approx.4 seconds.

108 Lighting

For deactivation operate the sameprocedure as described above. f willnot flash when function isdeactivated.

Adaptive forward lightingAdaptive forward lighting ensuresbetter illumination of bends, crossingsand narrow bends.

Curve lighting

The light beam pivots based onsteering wheel position and speed.

Corner lightingOn tight bends or when turning off,depending on the steering angle orthe indicator light signal, an additionalleft or right reflector is switched onwhich illuminates the road in thedirection of travel. It is activated up toa speed of 25 mph.

Reversing functionIf the headlights are on and reversegear is engaged, both corner lightsare switched on. They remainilluminated for 20 seconds afterdisengaging reverse gear or untildriving faster than 10 mph forward.

Hazard warning flashers

Operated with the ¨ button.In the event of an accident with airbagdeployment the hazard warningflashers are activated automatically.

Lighting 109

Turn and lane-change signals

lever up = right turn signallever down = left turn signal

If the lever is moved past theresistance point, the turn signal isswitched on constantly. When thesteering wheel moves back, the turnsignal is automatically deactivated.For three flashes, e.g. when changinglanes, press the lever until resistanceis felt and then release.With a trailer connected, turn signalflashes six times when pressing thelever until resistance is felt and thenreleasing.

Move the lever to the resistance pointand hold for longer indication.Switch the turn signal off manually bymoving the lever to its originalposition.

Front fog lights

Operated with the > button.Light switch in position AUTO:switching on front fog lights will switchheadlights on automatically.

Rear fog lights

Operated with the r button.Light switch in position AUTO:switching on rear fog light will switchheadlights on automatically.Light switch in position 8: rear foglight can only be switched on withfront fog lights.The vehicle rear fog light isdeactivated when towing.

110 Lighting

Parking lights

When the vehicle is parked, theparking lights on one side can beactivated:1. Switch off ignition.2. Move turn signal lever all the way

up (right parking lights) or down(left parking lights).

Confirmed by a signal and thecorresponding turn signal controlindicator.

Reversing lightsThe reversing lights come on whenthe ignition is on and reverse gear isselected.

Misted light coversThe inside of the light housing maymist up briefly in poor, wet and coldweather conditions, in heavy rain orafter washing. The mist disappearsquickly by itself; to help switch on theheadlights.

Interior lightingInstrument panel illuminationcontrol

Brightness of the following lights canbe adjusted when the exterior lightsare on:■ Instrument panel illumination■ Info-Display■ Illuminated switches and operation

elementsTurn thumb wheel A until the requiredbrightness is obtained.

Lighting 111

On vehicles with light sensor thebrightness can only be adjusted whenthe exterior lights are on and the lightsensor detects night conditions.

Interior lightsDuring entry and exit of the vehicle,the front and rear courtesy lightsautomatically switch on and then offafter a delay.NoteIn the event of an accident withairbag deployment the courtesylights are turned on automatically.

Front courtesy light

Operate rocker switch:w = automatic switching on

and off.press u = on.press v = off.

Rear courtesy lights

Illuminate in conjunction with the frontcourtesy light depending on rockerswitch position.

Reading lights

Operated with s and t buttons infront and rear courtesy lights.

Sunvisor lightsIlluminate when the cover is opened.

112 Lighting

Lighting featuresCentre console lightingSpotlight incorporated in the interiorlighting comes on when headlightsare switched on.

Entry lightingWelcome lightingHeadlights, tail lights, reversing lights,number plate lights, instrument panellight and interior lights are switchedon for a short time by unlocking thevehicle with the radio remote control.This function facilitates locating thevehicle when it is dark.The lighting switches off immediatelywhen the ignition key is turned toposition 1.Activation or deactivation of thisfunction can be changed in the menuSettings in the Info-Display. Vehiclepersonalisation 3 99.The settings can be saved for the keybeing used 3 20.

The following lights will additionallyswitch on when the driver's door isopened:■ All switches■ Driver Information Center

Exit lightingThe following lights switch on if thekey is removed from the ignitionswitch:■ Interior lights■ Instrument panel lightThey will switch off automatically aftera delay. Theatre lighting is activatedif the driver's door is opened duringthis time.The puddle light illuminates when theaccording door is opened.Headlights, tail lights, reversing lightsand number plate lights illuminate thesurrounding area for an adjustabletime after leaving the vehicle.

Switching on

1. Switch off ignition.2. Remove ignition key.3. Open driver's door.4. Pull turn signal lever.5. Close driver's door.

If the driver's door is not closed thelights switch off after 2 minutes.Exit lighting is switched offimmediately if the turn signal lever ispulled while the driver's door is open.

Lighting 113

Activation, deactivation and durationof this function can be changed in themenu Settings in the Info-Display.Vehicle personalisation 3 99.The settings can be saved for the keybeing used 3 20.

Battery discharge protectionSwitching off electric lightsTo prevent discharge of the batterywhen the ignition is switched off,some interior lights are switched offautomatically after some time.

114 Climate control

Climate control

Climate control systems ............. 114Air vents ..................................... 119Maintenance .............................. 120

Climate control systemsHeating and ventilation system

Controls for:■ Temperature■ Air distribution■ Fan speed■ Demisting and defrostingHeated rear window Ü 3 30.

Temperaturered = warmblue = cold

Heating will not be fully effective untilthe engine has reached normaloperating temperature.

Air distributions = to windscreen and front door

windowsM = to head area via adjustable air

ventsK = to foot well

All combinations are possible.

Fan speedAdjust the air flow by switching the fanto the desired speed.

Demisting and defrosting■ Press button V: fan automatically

switches to higher speed, the airdistribution is directed towards thewindscreen.

■ Set temperature control to warmestlevel.

■ Switch on heated rear window Ü.■ Open side air vents as required and

direct them towards the doorwindows.

Climate control 115

Air conditioning system

In addition to the heating andventilation system, the airconditioning system has:n = cooling4 = air recirculation

Heated seats ß 3 38, Heatedsteering wheel * 3 75.

Cooling nOperated with the n button and isfunctional only when the engine andfan are running.

The air conditioning system cools anddehumidifies (dries) as soon as theoutside temperature is slightly abovethe freezing point. Thereforecondensation may form and drip fromunder the vehicle.If no cooling or drying is required,switch the cooling system off to savefuel.

Air recirculation system 4Operated with the 4 button.

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up. The qualityof the passenger compartment airdeteriorates, which may cause thevehicle occupants to feel drowsy.

Maximum coolingBriefly open the windows so that hotair can disperse quickly.

■ Cooling n on.■ Air circulation system 4 on.■ Press air distribution switch M.■ Set temperature control to coldest

level.■ Set fan speed to highest level.■ Open all vents.

116 Climate control

Demisting and defrosting thewindows V

■ Press button V: fan automaticallyswitches to higher speed, the airdistribution is directed towards thewindscreen.

■ Switch cooling n on.■ Set temperature control to warmest

level.■ Switch on heated rear window Ü.■ Open side air vents as required and

direct them towards the doorwindows.

Electronic climate controlsystemThe dual zone climate control allowsdifferent climatisation temperaturesfor driver and front passenger side.

Controls for:■ Temperature on driver side■ Air distribution■ Fan speed■ Temperature on front passenger

sideAUTO = automatic modeu = manual air recirculation

t = automatic air recirculationV = demisting and defrosting

Heated rear window Ü 3 30.The preselected temperature isautomatically regulated. In theautomatic mode the fan speed and airdistribution automatically regulate theair flow.The system can be manually adaptedvia the use of air distribution and airflow controls.

Each change of settings is shown inthe Info-Display for a few seconds.

Climate control 117

The electronic climate control systemis only fully operational when theengine is running.

Automatic mode AUTO

Basic setting for maximum comfort:■ Press AUTO button, the air

conditioning is activatedautomatically.

■ Open all air vents.■ Set the preselected temperatures

for driver and front passenger usingthe left and right rotary knob.

■ Recommended comfort setting is22 °C.

The fan speed regulation in automaticmode can be changed in the menuSettings.Vehicle personalisation 3 99.All air vents are actuatedautomatically in automatic mode. Theair vents should therefore always beopen.

Temperature preselectionTemperatures can be set to thedesired value.

If the minimum temperature is set, theclimate control system runs atmaximum cooling.

If the maximum temperature is set,the climate control system runs atmaximum heating.

Demisting and defrosting thewindows V■ Press button V.■ Press cooling button n.■ Temperature and air distribution

are set automatically and the fanruns at high speed.

■ Switch on heated rear window Ü.■ To return to previous mode: press

button V.

Manual settingsClimate control system settings canbe changed by activating the buttonsand rotary knobs as follows.Changing a setting will deactivate theautomatic mode.

118 Climate control

Press lower button x to decrease orupper button x to increase fan speed.The fan speed is indicated by thenumber of segments in the display.Pressing the lower button longer, fanand cooling are switched off.Pressing the upper button longer, thefan runs at maximum speed.To return to automatic mode: PressAUTO button.

Air distributionPress s, M or K for desiredadjustment. Activation is indicated bythe LED in the button.

s = to windscreen and front doorwindows

M = to head area via adjustable airvents

K = to foot well

All combinations are possible.Return to automatic air distribution:Deactivate corresponding setting orpress button AUTO.

CoolingActivate or deactivate with the nbutton.The air conditioning system cools anddehumidifies (dries) when outsidetemperature is above a specific level.Therefore condensation may formand drip from under the vehicle.If no cooling or drying is required,switch the cooling system off to savefuel.

Air recirculation mode

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up. The qualityof the passenger compartment airdeteriorates, which may cause thevehicle occupants to feel drowsy.

Climate control 119

Automatic air recirculation tThe automatic air recirculationsystem has an air quality sensorwhich can switch automatically torecirculation.Activation is indicated by the LED inthe button.Switch to manual air recirculation asnecessary.

Manual air recirculation uPress button once to activate themanual air recirculation mode.Activation is indicated by the LED inthe button.

Basic settingsSome settings can be changed in themenu Settings in the Info-Display.Vehicle personalisation 3 99.

Auxiliary heaterAir heaterQuickheat is an electric auxiliary airheater which automatically warms upthe passenger compartment morequickly.

Air ventsAdjustable air vents

To open the vent, turn the adjusterwheel to the right. Adjust the airamount at the vent outlet by turningthe adjuster wheel.

Direct the flow of air by tilting andswivelling the slats.To close the vent, turn the adjusterwheel to the left.

9 Warning

Do not attach any objects to theslats of the air vents. Risk ofdamage and injury in case of anaccident.

Fixed air ventsAdditional air vents are locatedbeneath the windscreen and doorwindows and in the foot wells.

120 Climate control

MaintenanceAir intake

The air intake in front of thewindscreen in the enginecompartment must be kept clear toallow air intake. Remove any leaves,dirt or snow.

Pollen filterCabin air filtrationA particle filter cleans the cabin airfrom dust, soot, pollen and spores.

Active carbon filterIn addition to the particle filter theactive carbon filter reduces odours.

Air conditioning regularoperationIn order to ensure continuouslyefficient performance, cooling mustbe operated for a few minutes oncea month, irrespective of the weatherand time of year. Operation withcooling is not possible when theoutside temperature is too low.

ServiceFor optimal cooling performance, it isrecommended to annually check theclimate control system, starting3 years after initial vehicleregistration, including:■ Functionality and pressure test■ Heating functionality■ Leakage check■ Check of drive belts

■ Cleaning of condenser andevaporator drainage

■ Performance check

Driving and operating 121

Driving andoperating

Driving hints ............................... 121Starting and operating ............... 121Engine exhaust .......................... 123Automatic transmission .............. 125Manual transmission .................. 128Brakes ........................................ 129Ride control systems ................. 131Cruise control ............................. 133Object detection systems ........... 134Fuel ............................................ 136Towing ....................................... 138

Driving hintsControl of the vehicleNever coast with engine notrunningMany systems will not function in thissituation (e.g. brake servo unit, powersteering). Driving in this manner isa danger to yourself and others.

PedalsTo ensure the pedal travel isuninhibited, there must be no mats inthe area of the pedals.

Starting and operatingNew vehicle running-inDo not brake unnecessarily hard forthe first few journeys.During the first drive, smoke mayoccur because of wax and oilevaporating off the exhaust system.Park the vehicle in the open fora while after the first drive and avoidinhaling the fumes.During the running-in period fuel andengine oil consumption may behigher and the cleaning process ofthe diesel particle filter may takeplace more often.Diesel particle filter 3 123.

122 Driving and operating

Ignition switch positions

0 = Ignition off1 = Steering wheel lock released,

ignition off2 = Ignition on, for diesel engine:

preheating3 = Starting

Starting the engine

Manual transmission: operate clutch.Automatic transmission: operatebrake and move the selector lever toP or N.Do not operate accelerator pedal.Diesel engine: turn the key to position2 for preheating until controlindicator ! goes out.Turn the key briefly to position 3 andrelease: an automatic procedureoperates the starter with a short delayas long as the engine is running, seeAutomatic Starter Control.

Before restarting or to switch off theengine, turn the key back to 0.

Automatic Starter ControlThis function controls the enginestarting procedure. The driver doesnot have to hold the key in position3. Once applied, the system will go onstarting automatically until the engineis running. Because of the checkingprocedure, the engine starts runningafter a short delay.Possible reasons for a non-startingengine:■ Clutch pedal not operated (manual

transmission)■ Brake pedal not operated or

selector lever not in P or N(automatic transmission)

■ Timeout occurred

Overrun cut-offThe fuel supply is automatically cut offduring overrun, i.e. when the vehicleis driven with a gear engaged butaccelerator is released.

Driving and operating 123

Parking■ Do not park the vehicle on an easily

ignitable surface. The hightemperature of the exhaust systemcould ignite the surface.

■ Always apply parking brake.Pull switch m.

■ Switch off the engine and ignition.Turn the steering wheel until thesteering wheel lock engages.

■ If the vehicle is on a level surface oruphill slope, engage first gear or setthe selector lever to P beforeswitching off the ignition. On anuphill slope, turn the front wheelsaway from the kerb.If the vehicle is on a downhill slope,engage reverse gear or set theselector lever to P before switchingoff the ignition. Turn the frontwheels towards the kerb.

■ Lock the vehicle and activate theanti-theft alarm system.

NoteIn the event of an accident withairbag deployment, the engine isturned off automatically if the vehiclecomes to a standstill within a certaintime.

Engine exhaust

9 Danger

Engine exhaust gases containpoisonous carbon monoxide,which is colourless and odourlessand could be fatal if inhaled.If exhaust gases enter the interiorof the vehicle, open the windows.Have the cause of the faultrectified by a workshop.Avoid driving with an open loadcompartment, otherwise exhaustgases could enter the vehicle.

Diesel particle filterThe diesel particle filter system filtersharmful soot particles out of theexhaust gases. The system includesa self-cleaning function that runsautomatically during driving withoutany notification. The filter is cleanedby periodically burning off the sootparticles at high temperature. Thisprocess takes place automaticallyunder set driving conditions and may

124 Driving and operating

take up to 25 minutes. Typically itneeds between 7 and 12 minutes.Fuel consumption may be higherduring this period. The emission ofsmells and smoke during this processis normal.

Under certain driving conditions, e.g.short distances, the system cannotclean itself automatically.If the cleaning of the filter is requiredand if previous driving conditions didnot enable automatic cleaning, it willbe indicated by the control indicator%. Simultaneously Diesel partic. filter

is full continue driving or warningcode 55 appears in the DriverInformation Center.% illuminates when diesel particlefilter is full. Start cleaning process assoon as possible.% flashes when diesel particle filterhas reached the maximum fillinglevel. Start cleaning processimmediately to avoid damage to theengine.

Cleaning processTo activate cleaning process,continue driving, keeping enginespeed above 2000 revolutions perminute. Shift down if necessary.Diesel particle filter cleaning is thenstarted.If g illuminates additionally,cleaning is not possible, seek theassistance of a workshop.

Caution

If the cleaning process isinterrupted, there is a risk ofprovoking severe engine damage.

Cleaning takes place quickest at highengine speeds and loads.The control indicator % extinguishesas soon as the self-cleaningoperation is complete.

Catalytic converterThe catalytic converter reduces theamount of harmful substances in theexhaust gases.

Caution

Fuel grades other than those listedon pages 3 136, 3 185 coulddamage the catalytic converter orelectronic components.Unburnt petrol will overheat anddamage the catalytic converter.Therefore avoid excessive use ofthe starter, running the fuel tankdry and starting the engine bypushing or towing.

In the event of misfiring, unevenengine running, a reduction in engineperformance or other unusualproblems, have the cause of the fault

Driving and operating 125

rectified by a workshop as soon aspossible. In an emergency, drivingcan be continued for a short period,keeping vehicle speed and enginespeed low.

Automatic transmissionThe automatic transmission permitsautomatic gearshifting (automaticmode) or manual gearshifting(manual mode).

Transmission display

The mode or selected gear is shownin the transmission display.

Selector lever

P = park position, wheels arelocked, engage only when thevehicle is stationary and theparking brake is applied

R = reverse gear, engage onlywhen the vehicle is stationary

N = neutralD = automatic mode with all gears

The selector lever is locked in P andcan only be moved when the ignitionis on and the brake pedal is applied.

126 Driving and operating

Without brake pedal applied, thecontrol indicator j illuminates.If the selector lever is not in P whenthe ignition is switched off, the controlindicator j and P flash.To engage P or R, press the releasebutton.The engine can only be started withthe lever in position P or N. Whenposition N is selected, press the brakepedal or apply the parking brakebefore starting.

Do not accelerate while engaginga gear. Never depress the acceleratorpedal and brake pedal at the sametime.When a gear is engaged, the vehicleslowly begins to creep when thebrake is released.

Engine brakingTo utilise the engine braking effect,select a lower gear in good time whendriving downhill, see manual mode.

Rocking the vehicleRocking the vehicle is onlypermissible if the vehicle is stuck insand, mud or snow. Move the selectorlever between D and R in a repeatpattern. Do not race the engine andavoid sudden acceleration.

ParkingApply the parking brake and engageP.The ignition key can only be removedwhen the selector lever is in positionP.

Manual mode

Move selector lever out of position Dtowards the left and then forwards orbackwards.< = Shift to a higher gear.

] = Shift to a lower gear.

If a higher gear is selected whenvehicle speed is too low, or a lowergear when vehicle speed is too high,the shift is not executed. This cancause a message in the DriverInformation Center.

Driving and operating 127

In manual mode no automatic shiftingto a higher gear takes place at highengine revolutions.

Electronic driving programmes■ Following a cold start, the operating

temperature programme increasesengine speed to quickly bring thecatalytic converter to the requiredtemperature.

■ The automatic neutral shift functionautomatically shifts to idling whenthe vehicle is stopped witha forward gear engaged and thebrake pedal is pressed.

■ Special programmes automaticallyadapt the shifting points whendriving up inclines or down hills.

KickdownIf the accelerator pedal is presseddown completely in automatic mode,the transmission shifts to a lower geardepending on engine speed.

FaultIn the event of a fault, g illuminates.Additionally a code number ora vehicle message is displayed in theDriver Information Center. Vehiclemessages 3 94.The transmission no longer shiftsautomatically. Continued travel ispossible with manual shifting.Only the highest gear is available.Depending on the fault, second gearmay also be available in manualmode. Shift only when vehicle is ata standstill.Have the cause of the fault remediedby a workshop.

Interruption of power supplyIn the event of an interruption ofpower supply, the selector levercannot be moved out of the Pposition. The ignition key cannot beremoved from the ignition switch.If the battery is discharged, start thevehicle using jump leads 3 173.

If the battery is not the cause of thefault, release the selector lever.1. Apply the parking brake.

2. Grasp the selector lever trim at themarked position and pull tounlatch at the back.

3. Fold the selector lever trimupwards. Pull to unlatch at thefront.

4. Move the selector lever trim to theleft. Take care that the plug andthe wiring harness at the bottomare not damaged

128 Driving and operating

5. Insert a screwdriver into theopening as far as it will go andmove the selector lever out of P orN. If P or N is engaged again, theselector lever will be locked inposition again. Have the cause ofthe power supply interruptionremedied by a workshop.

6. Mount the selector lever trim ontothe centre console and refit.

Manual transmission

To engage reverse, with the vehiclestationary press the release button onthe selector lever and engage thegear.If the gear does not engage, set thelever in neutral, release the clutchpedal and depress again; then repeatgear selection.Do not grind the clutch unnecessarily.When operating, depress the clutchpedal completely. Do not use thepedal as a foot rest.

Caution

It is not advisable to drive with thehand resting on the selector lever.

Driving and operating 129

BrakesThe brake system comprises twoindependent brake circuits.If a brake circuit fails, the vehicle canstill be braked using the other brakecircuit. However, braking effect isachieved only when the brake pedalis depressed firmly. Considerablymore force is needed for this. Thebraking distance is extended. Seekthe assistance of a workshop beforecontinuing your journey.When the engine is not running, thesupport of the brake servo unitdisappears once the brake pedal hasbeen depressed once or twice.Braking effect is not reduced, butbraking requires significantly greaterforce. It is especially important to bearthis in mind when being towed.Control indicator R 3 86.

Antilock brake systemAntilock brake system (ABS)prevents the wheels from locking.

ABS starts to regulate brake pressureas soon as a wheel shows a tendencyto lock. The vehicle remainssteerable, even during hard braking.ABS control is made apparentthrough a pulse in the brake pedaland the noise of the regulationprocess.For optimum braking, keep the brakepedal fully depressed throughout thebraking process, despite the fact thatthe pedal is pulsating. Do not reducethe pressure on the pedal.Control indicator u 3 87.

Adaptive brake lightDuring full braking, all three brakelights flash for the duration of ABScontrol.

Fault

9 Warning

If there is a fault in the ABS, thewheels may be liable to lock dueto braking that is heavier thannormal. The advantages of ABSare no longer available. Duringhard braking, the vehicle can nolonger be steered and mayswerve.

Have the cause of the fault remediedby a workshop.

130 Driving and operating

Parking brakeElectrical parking brake

Applying when vehicle is stationaryPull switch m, the electrical parkingbrake operates automatically withadequate force. For maximum force,e.g. parking with trailer or on inclines,pull switch m twice.The electrical parking brake canalways be activated, even if theignition is off.

Do not operate electrical parkingbrake system too often withoutengine running because this willdischarge the battery.Before leaving the vehicle, check theelectrical parking brake status.Control indicator m 3 86.

ReleasingSwitch on ignition. Keep foot brakepedal depressed and then pushswitch m.

Drive away functionDepressing clutch pedal (manualtransmission) or engaging D(automatic transmission) and thendepressing the accelerator pedalreleases the electrical parking brakeautomatically. This is not possiblewhen the switch is pulled at the sametime.This function also helps driving awayon inclines.Aggressive drive away may reducelife time of wear parts.

Dynamic braking when vehicle ismovingWhen the vehicle is moving and theswitch m is kept pulled, the electricalparking brake system will deceleratethe vehicle, but will not applystatically.As soon as the switch m is released,dynamic braking will be stopped.

FaultFailure mode of electrical parkingbrake is indicated by control indicatorj and by a code number or a vehiclemessage which is displayed in theDriver Information Center. Vehiclemessages 3 94.Apply electrical parking brake: pulland hold the switch m for more than5 seconds. If control indicator milluminates, electrical parking brake isapplied.Release electrical parking brake:push and hold the switch m for morethan 2 seconds. If control indicatorm goes out, electrical parking brakeis released.

Driving and operating 131

Control indicator m flashes: electricalparking brake is not fully applied orreleased. When continuouslyflashing, release electrical parkingbrake and retry applying.

Brake assistIf the brake pedal is depressedquickly and forcefully, maximumbrake force is automatically applied(full braking).Maintain steady pressure on thebrake pedal for as long as full brakingis required. Maximum brake force isautomatically reduced when thebrake pedal is released.

Hill start assistThe system helps driving away oninclines.If the foot brake pedal is released oninclines the vehicle is hold for2 seconds preventing unintendedmovement. If the vehicle is launchedearlier, the brake is automaticallyreleased.

Ride control systemsTraction Control systemThe Traction Control system (TC) isa component of the electronic stabilitycontrol system.TC improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip, bypreventing the drive wheels fromspinning.As soon as the drive wheels starts tospin, engine output is reduced andthe wheel spinning the most is brakedindividually. This considerablyimproves the driving stability of thevehicle on slippery road surfaces.TC is operational as soon as thecontrol indicator b extinguishes.When TC is active b flashes.

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator b 3 88.

Deactivation

TC can be switched off when spinningof drive wheels is required: pressbutton b briefly.Control indicator k illuminates.

132 Driving and operating

TC is reactivated by pressing the bbutton again.TC is also reactivated the next timethe ignition is switched on.

Electronic Stability ControlElectronic stability control (ESC)improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip. It alsoprevents the drive wheels fromspinning.As soon as the vehicle starts toswerve (understeer/oversteer),engine output is reduced and thewheels are braked individually. Thisconsiderably improves the drivingstability of the vehicle on slippery roadsurfaces.ESC is operational as soon as thecontrol indicator b extinguishes.When ESC is active b flashes.

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator b 3 88.

Deactivation

For very high-performance drivingESC can be deactivated: hold buttonb depressed for approx. 7 seconds.Control indicator n illuminates.

ESC is reactivated by pressing theb button again. If the TC system waspreviously disabled, both TC andESC are reactivated.ESC is also reactivated the next timethe ignition is switched on.

Driving and operating 133

Cruise controlThe cruise control can store andmaintain speeds of approx. 20 to120 mph. Deviations from the storedspeeds may occur when driving uphillor downhill.For safety reasons the cruise controlcannot be activated until the footbrake has been operated once.Activating in first gear is not possible.

Do not use the cruise control if it is notadvisable to maintain a constantspeed.

With automatic transmission, onlyactivate cruise control in automaticmode.Control indicator m 3 90.

Switching onPress rocker switch m at the upperend, control indicator m illuminateswhite.

ActivationAccelerate to the desired speed andturn thumb wheel to SET/-, thecurrent speed is stored andmaintained. Control indicator milluminates green. Accelerator pedalcan be released.Vehicle speed can be increased bydepressing the accelerator pedal.When the accelerator pedal isreleased, the previously stored speedis resumed.

Increase speedWith cruise control active, hold thumbwheel turned to RES/+ or briefly turnto RES/+ repeatedly: speedincreases continuously or in smallincrements.

Alternatively accelerate to the desiredspeed and store by turning to RES/+.

Reduce speedWith cruise control active, hold thumbwheel turned to SET/- or briefly turnto SET/- repeatedly: speeddecreases continuously or in smallincrements.

DeactivationPress button y, control indicator milluminates white. Cruise control isdeactivated.The stored speed ismemorised.Automatic deactivation:■ vehicle speed below approx.

20 mph,■ the brake pedal is depressed,■ the clutch pedal is depressed,■ selector lever in N,■ the Traction Control system or

electronic stability control isoperating.

134 Driving and operating

Resume stored speedTurn thumb wheel to RES/+ ata speed above 20 mph. The storedspeed will be obtained.

Switching offPress rocker switch m at the lowerend, control indicator m extinguishes.The stored speed is deleted.Switching off the ignition also deletesthe stored speed.

Object detection systemsParking assist

The parking assist makes parkingeasier by measuring the distancebetween the vehicle and obstacles,and giving acoustic signals. It is thedriver, however, who bears fullresponsibility for the parkingmanoeuvre.The system consists of four ultrasonicparking sensors in the rear bumper. Ifthe vehicle is equipped with a front

parking assist the system consists offour additional ultrasonic parkingsensors in the front bumper.Control indicator r 3 88.

Activation

When reverse gear is engaged, thesystem is activated automatically.The front parking assist can also beactivated at a low speed by pressingthe r button.An illuminated LED in the parkingassist button indicates that thesystem is ready to operate.

Driving and operating 135

An obstacle is indicated by a buzzingsound. The interval between thesounds becomes shorter as thevehicle gets closer to the obstacle.When the distance is less than 1 ft,the buzzing is continuous.

DeactivationDeactivate the system by pressingthe r button.The LED in the button will go out andPark Assist Off will be displayed in theDriver Information Center.The system is deactivatedautomatically at a certain speed.

FaultIn the event of a fault in the system,r illuminates and a message isdisplayed in the Driver InformationCenter.Additionally, r illuminates ora vehicle message is displayed in theDriver Information Center ifa malfunction of the system due totemporary conditions like snowcovered sensors is detected.Vehicle messages 3 94.

Important hints for using theparking assist systems

9 Warning

Under certain circumstances,various reflective surfaces onobjects or clothing as well asexternal noise sources may causethe system to fail to detectobstacles.Special attention has to be paid tolow obstacles which can damagethe lower part of the bumper. Ifsuch obstacles leave the detectionarea of the sensors duringapproach of the vehicle,a continuous warning tone willsound.

Caution

Performance of the sensor can bereduced when sensors arecovered, e.g. by ice or snow.Performance of the parking assistsystems can be reduced due toheavy loading.Special conditions apply if thereare taller vehicles involved (e.g.off-road vehicles, mini vans,vans). Object identification in theupper part of these vehiclescannot be guaranteed.Objects with a very small reflectioncross section, like objects ofnarrow size or soft materials, maynot be detected by the system.Parking assist will not avoida collision with objects which areout of the detection range of thesensors.

136 Driving and operating

NoteThe parking assist systemautomatically detects factory-fittedtowing equipment. It is deactivatedwhen the connector is plugged in.The sensor may detect a non-existent object (echo disturbance)caused by external acoustic ormechanical disturbances.

FuelFuel for petrol enginesOnly use unleaded fuel that complieswith DIN EN 228.Equivalent standardised fuels with anethanol content of max. 10 % byvolume may be used. In this case onlyuse fuel that complies withDIN 51625.Use fuel with the recommendedoctane rating 3 185. Use of fuel withtoo low an octane rating can reduceengine power and torque and slightlyincreases fuel consumption.

Caution

Use of fuel with too low an octanerating could lead to uncontrolledcombustion and engine damage.

Fuel for diesel enginesOnly use diesel fuel that complieswith DIN EN 590. The fuel must havelow sulphur content (max. 10 ppm).Equivalent standardised fuels with

a biodiesel (= FAME according toEN 14214) content of max. 7 % byvolume (like DIN 51628 or equivalentstandards) may be used.Do not use marine diesel oils, heatingoils or entirely or partially plant-baseddiesel fuels, such as rape seed oil orbio diesel, Aquazole and similardiesel-water emulsions. Diesel fuelsmust not be diluted with fuels forpetrol engines.The flow and filterability of diesel fuelare temperature-dependent. Whentemperatures are low, refuel withdiesel fuel with guaranteed winterproperties.

Driving and operating 137

Refuelling

9 Danger

Before refuelling, switch off engineand any external heaters withcombustion chambers. Switch offany mobile phones.Follow the operating and safetyinstructions of the filling stationwhen refuelling.

9 Danger

Fuel is flammable and explosive.No smoking. No naked flames orsparks.If you can smell fuel in yourvehicle, have the cause of thisremedied immediately bya workshop.

Fuel filler flap is located at right rearside of vehicle.

The fuel filler flap can only be openedif the vehicle is unlocked. Pull flap atthe recess and open.

The fuel filler cap can be retained inthe bracket on the fuel filler flap.

Caution

Wipe off any overflowing fuelimmediately.

Fuel filler capOnly use genuine fuel filler caps.Diesel-engined vehicles have specialfuel filler caps.

138 Driving and operating

Fuel consumption - CO2-EmissionsThe determination of fuelconsumption is regulated byEuropean directive715/2007 692/2008 A.The directive is oriented to actualdriving practices: Urban driving israted at approx. 1/3 and extra urbandriving with approx. 2/3. Cold startsand acceleration phases are alsotaken into consideration.The specification of CO2 emission isalso a constituent of the directive.The figures given must not be takenas a guarantee for the actual fuelconsumption of a particular vehicle.Furthermore, fuel consumption isdependent on personal driving styleas well as road and traffic conditions.All values are based on the EU basemodel with standard equipment.The calculation of fuel consumptiontakes into account the vehicle’s kerbweight, ascertained in accordancewith the regulations. Optional

equipment may result in slightlyhigher fuel consumption andCO2 emission levels and a lowermaximum speed.Fuel consumption, CO2 emissions3 186.

TowingGeneral informationOnly use towing equipment that hasbeen approved for your vehicle.Entrust retrofitting of towingequipment to a workshop. It may benecessary to make changes thataffect the cooling system, heatshields or other equipment.Fitting of towing equipment couldcover the opening of the towing eye.If this is the case use the coupling ballbar for towing. Always keep thecoupling ball bar in the vehicle.Installation dimensions of factory-fitted towing equipment 3 192.

Driving characteristics andtowing tipsBefore attaching a trailer, lubricatethe coupling ball. However, do not doso if a stabiliser, which acts on thecoupling ball, is being used to reducesnaking movements.

Driving and operating 139

For trailers with low driving stabilityand trailers with a permitted grossvehicle weight of more than 1100 kgthe use of a stabiliser is stronglyrecommended when driving above50 mph.If the trailer starts snaking, drive moreslowly, do not attempt to correct thesteering and brake sharply ifnecessary.When driving downhill, drive in thesame gear as if driving uphill anddrive at a similar speed.Adjust tyre pressure to the valuespecified for full load 3 189.

Trailer towingTrailer loadsThe permissible trailer loads arevehicle and engine-dependentmaximum values which must not beexceeded. The actual trailer load isthe difference between the actualgross weight of the trailer and theactual coupling socket load with thetrailer coupled.

The permissible trailer loads arespecified in the vehicle documents. Ingeneral, they are valid for gradientsup to max. 12 %.The permitted trailer load applies upto the specified incline and up to analtitude of 3300 ft above sea level.Since engine power decreases asaltitude increases due to the airbecoming thinner, therefore reducingclimbing ability, the permissible grosstrain weight also decreases by 10 %for every 3300 ft of additional altitude.The gross train weight does not haveto be reduced when driving on roadswith slight inclines (less than 8 %, e.g.motorways).The permissible gross train weightmust not be exceeded. This weight isspecified on the identification plate3 184.

Vertical coupling loadThe vertical coupling load is the loadexerted by the trailer on the couplingball. It can be varied by changing theweight distribution when loading thetrailer.

The maximum permissible verticalcoupling load (75 kg) is specified onthe towing equipment identificationplate and in the vehicle documentsAlways aim for the maximum load,especially in the case of heavytrailers. The vertical coupling loadshould never fall below 25 kg.

Rear axle loadWhen the trailer is coupled and thetowing vehicle fully loaded, thepermissible rear axle load (seeidentification plate or vehicledocuments) may be exceeded by60 kg, the gross vehicle weight ratingmay be exceeded by 70 kg. If thepermissible rear axle load isexceeded, a maximum speed of60 mph applies.

Trailer stability assistIf the system detects snakingmovements, engine power is reducedand the vehicle/trailer combination isselectively braked until the snakingceases. While the system is working,keep steering wheel as still aspossible.

140 Driving and operating

Trailer stability assist (TSA) isa function of the electronic stabilitycontrol 3 132.

Vehicle care 141

Vehicle care

General Information ................... 141Vehicle checks ........................... 142Bulb replacement ....................... 147Electrical system ........................ 156Vehicle tools .............................. 162Wheels and tyres ....................... 163Jump starting ............................. 173Towing ....................................... 175Appearance care ....................... 177

General InformationAccessories and vehiclemodificationsWe recommend the use of genuineparts and accessories and factoryapproved parts specific for yourvehicle type. We cannot assess orguarantee reliability of other products- even if they have a regulatory orotherwise granted approval.Do not make any modifications to theelectrical system, e.g. changes ofelectronic control units (chip tuning).

Vehicle storageStorage for a long period of timeIf the vehicle is to be stored for severalmonths:■ Wash and wax the vehicle.■ Have the wax in the engine

compartment and underbodychecked.

■ Clean and preserve the rubberseals.

■ Change the engine oil.

■ Drain the washer fluid reservoir.■ Check the coolant antifreeze and

corrosion protection.■ Adjust tyre pressure to the value

specified for full load.■ Park the vehicle in a dry, well

ventilated place. Engage first orreverse gear or set selector lever toP. Prevent the vehicle from rolling.

■ Do not apply the parking brake.■ Open the bonnet, close all doors

and lock the vehicle.■ Disconnect the clamp from the

negative terminal of the vehiclebattery. Beware that all systems arenot functional, e.g. anti-theft alarmsystem.

Putting back into operationWhen the vehicle is to be put back intooperation:■ Connect the clamp to the negative

terminal of the vehicle battery.Activate the electronics of thepower windows.

■ Check tyre pressure.■ Fill up the washer fluid reservoir.

142 Vehicle care

■ Check the engine oil level.■ Check the coolant level.■ Fit the number plate if necessary.

End-of-life vehicle recoveryInformation on end-of-life vehiclerecovery centres and the recycling ofend-of-life vehicles is available on ourwebsite. Only entrust this work to anauthorised recycling centre.

Vehicle checksPerforming work

9 Warning

Only perform engine compartmentchecks when the ignition is off.The cooling fan may startoperating even if the ignition is off.

9 Danger

The ignition system usesextremely high voltage. Do nottouch.

BonnetOpening

Pull the release lever and return it toits original position.

Vehicle care 143

Press the safety catch and open thebonnet.

Secure the bonnet support.

ClosingBefore closing the bonnet, press thesupport into the holder.Lower the bonnet and allow it to dropinto the catch. Check that the bonnetis engaged.

Engine oilThe engine oil level is checkedautomatically, Vehicle messages3 94. However, check the engine oillevel manually on a regular basis toprevent damage to the engine.Ensure that the correct specificationof oil is used. Recommended fluidsand lubricants 3 181.Check with the vehicle on a levelsurface. The engine must be atoperating temperature and switchedoff for at least 5 minutes.Pull out the dipstick, wipe it clean,insert it to the stop on the handle, pullout and read the engine oil level.Insert dipstick to the stop on thehandle and make half a turn.

Different dipsticks are useddepending on engine variant.

144 Vehicle care

When the engine oil level hasdropped to the MIN mark, top upengine oil.

We recommend the use of the samegrade of engine oil that was used atlast change.The engine oil level must not exceedthe MAX mark on the dipstick.

Caution

Overfilled engine oil must bedrained or suctioned out.

Capacities 3 189.

Fit the cap on straight and tighten it.

Engine coolantThe coolant provides freezeprotection down to approx. -28 °C.

Caution

Only use approved antifreeze.

Coolant level

Caution

Too low a coolant level can causeengine damage.

If the cooling system is cold, thecoolant level should be above thefilling line mark. Top up if the level islow.

9 Warning

Allow the engine to cool beforeopening the cap. Carefully openthe cap, relieving the pressureslowly.

To top up use a 1:1 mixture ofapproved coolant concentrate mixedwith clean tap water. If no coolantconcentrate is available, use cleantap water. Install the cap tightly. Have

Vehicle care 145

the coolant concentration checkedand have the cause of the coolantloss remedied by a workshop.

Washer fluid

Fill with clean water mixed witha suitable quantity of washer fluidwhich contains antifreeze. For thecorrect mixing ratio refer to thewasher fluid container.

Caution

Only washer fluid with a sufficientantifreeze concentration providesprotection at low temperatures ora sudden drop in temperature.

BrakesIn the event of minimum thickness ofthe brake lining, g illuminates.Additionally a code number ora vehicle message is displayed in theDriver Information Center. Vehiclemessages 3 94.Continued driving is possible buthave the brake lining replaced assoon as possible.Once new brake linings are installed,do not brake unnecessarily hard forthe first few journeys.

Brake fluid

9 Warning

Brake fluid is poisonous andcorrosive. Avoid contact with eyes,skin, fabrics and painted surfaces.

The brake fluid level must be betweenthe MIN and the MAX marks.When topping up, ensure maximumcleanliness as contamination of thebrake fluid can lead to brake systemmalfunctions. Have the cause of theloss of brake fluid remedied bya workshop.

146 Vehicle care

Only use high-performance brakefluid approved for the vehicle.Brake and clutch fluid 3 181.

BatteryThe vehicle battery is maintenance-free provided that the driving profileallows sufficient charging of thebattery. Short-distance-driving andfrequent engine starts can dischargethe battery. Avoid the use ofunneccessary electrical consumers.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.Laying up the vehicle for more than4 weeks can lead to batterydischarge. Disconnect the clamp fromthe negative terminal of the vehiclebattery.

Ensure the ignition is switched offbefore connecting or disconnectingthe vehicle battery.The anti-theft alarm siren must bedeactivated as follows: Switch theignition on then off, disconnect thevehicle's battery within 15 seconds.Battery discharge protection 3 113.

Exchanging a battery

9 Warning

When fitting a battery with a lengthdeviating from the original one, itis essential to ensure a properfitting of the buffer element.

We recommend to consulta workshop.

Diesel fuel system bleedingIf the tank has been run dry, the dieselfuel system must be bled. Switch onthe ignition three times for15 seconds at a time. Then start theengine for a maximum of40 seconds. Repeat this process afterno less than 5 seconds. If the enginefails to start, seek the assistance ofa workshop.

Vehicle care 147

Wiper blade replacementWiper blades on the windscreen

Lift the wiper arm, press button todisengage the wiper blade andremove.Lower wiper arm carefully.

Wiper blade on the rear window

Lift wiper arm. Disengage wiper bladeas shown in illustration and remove.Lower wiper arm carefully.

Bulb replacementSwitch off the ignition and switch offthe relevant switch or close the doors.Only hold a new bulb at the base! Donot touch the bulb glass with barehands.Use only the same bulb type forreplacement.Replace headlight bulbs from withinthe engine compartment.

Halogen headlights

148 Vehicle care

Headlights have separate systems forlow beam 1 (outer bulbs) and highbeam 2 (inner bulbs).

Low beam

1. Rotate the cap 1 anticlockwiseand remove it.

2. Push the bulb holder upwards andwithdraw the bulb holder from thereflector.

3. Detach the bulb from the bulbholder and replace the bulb.

4. Insert the bulb holder into thereflector.

5. Fit the cap and rotate clockwise.

High beam

1. Rotate the cap 2 anticlockwiseand remove it.

2. Detach the plug from the bulb.

Vehicle care 149

3. Disengage the spring clip andthen swivel it backwards.

4. Remove and replace the bulb.

5. Swivel the spring clip forwardsand engage.

6. Attach the plug to the bulb.7. Fit the cap and rotate clockwise.

Sidelight/Daytime running light

1. Rotate the bulb holderanticlockwise and remove it.

2. Detach bulb from the bulb holderand replace it.

3. Insert the bulb holder into thereflector and rotate clockwise.

150 Vehicle care

Front turn signal

1. Rotate the bulb holderanticlockwise and remove it.

2. Rotate bulb anticlockwise andremove from bulb holder.

3. Replace bulb.4. Insert the bulb holder into the

reflector and rotate clockwise.

Adaptive forward lighting

Headlights have separate systems forlow beam and high beam 1 (outerbulbs) and additional high beam 2(inner bulbs). The cornering light isalso located behind the cover for theadditional high beam.

Low beam/High beam

1. Rotate the cap 1 anti-clockwiseand remove it.

Vehicle care 151

2. Push the bulb holder downwardsand withdraw the bulb holder fromthe reflector.

3. Detach the bulb from the bulbholder and replace the bulb.

4. Insert the bulb holder into thereflector.

5. Fit the cap and rotate clockwise.

Additional high beam

1. Rotate protective cover 2anticlockwise and remove.

2. Press catch and withdraw the bulbholder from the reflector.

3. Remove and replace the bulb.4. Press catch and insert the bulb

holder into the reflector.5. Fit the cap and rotate clockwise.

Cornering light1. Rotate protective cover 2

anticlockwise and remove.2. Detach the plug from the bulb.

152 Vehicle care

3. Disengage the spring clip andthen swivel it backwards.

4. Remove and replace the bulb.

5. Swivel the spring clip forwardsand engage.

6. Attach the plug to the bulb.7. Fit the cap and rotate clockwise.

Fog lights

The bulbs are accessible from thebottom.

1. Turn the bulb holder anticlockwiseand remove it from the reflector.

Vehicle care 153

2. Disengage the bulb holder fromthe plug connector by pressingthe retaining lug.

3. Remove and replace the bulbholder with bulb.

4. Attach the plug connector.5. Insert the bulb holder into the

reflector.6. Turn the bulb holder clockwise

and engage.

Tail lights

1. Release the cover and remove it.

2. Unscrew the two plastic securingnuts from the inside by hand.

3. Carefully withdraw the lightassembly from retaining pins andremove. Make sure that the cableduct remains in position.

4. Detach the wiring plug from thebulb carrier.

5. Unlatch the four retaining lugs andremove the bulb carrier.

154 Vehicle care

6. Remove and replace the bulb.Tail light and brake light (1)Tail light (2)Turn signal light (3)

7. Insert the bulb carrier into the taillight assembly. Connect thewiring plug. Fit light assemblyonto retaining pins and tighten thesecuring nuts. Close the coverand engage.

8. Switch on the ignition, operateand check all lights.

Tail lights in the tailgate frame

1. Open the tailgate and remove thecover with a screwdriver.

2. Press the retaining lug andremove the bulb carrierdownwards.

3. To replace the reverse light bulb(1), remove and replace the bulbTo replace the tail light bulb (2),push the bulb slightly into thesocket, rotate anticlockwise,remove and replace the bulb.

4. Insert the bulb carrier into theretainer.

5. Attach the cover.6. Switch on the ignition, operate

and check all lights.

Vehicle care 155

For replacing the tail light bulb andrear fog light bulb on the right side ofthe tailgate frame, proceed in thesame way.

Side turn signal lightsHave bulbs replaced by a workshop.

Number plate light

1. Insert screwdriver in recess of thecover, press to the side andrelease spring.Remove cover.

2. Remove the bulb holderdownwards, taking care not to pullon the cable.

3. Disengage the retaining lug andremove the bulb holder from thewiring plug.

4. Remove and replace the bulbholder with bulb.

5. Connect the wiring plug to thebulb holder.

6. Push the bulb holder into thehousing and close the cover.

Interior lightsCourtesy light, reading lightsHave bulbs replaced by a workshop.

Load compartment lightHave bulbs replaced by a workshop.

Puddle lights

1. Disengage the housing at thebottom and remove it.

156 Vehicle care

2. Press the retaining lug andwithdraw the connector.

3. Rotate the bulb holder clockwiseand remove.

4. Pull the bulb out of the bulb holderand replace it.

5. Insert the bulb holder into thehousing and turn it anticlockwise.

6. Plug in the connector.7. Attach the housing.

Instrument panel illuminationHave bulbs replaced by a workshop.

Electrical systemFusesData on the replacement fuse mustmatch the data on the defective fuse.There are three fuse boxes in thevehicle:■ in the front left of the engine

compartment,■ in the interior behind the storage

compartment, or, in right-handdrive vehicles, behind theglovebox,

■ behind a cover on the left side of theload compartment.

Before replacing a fuse, turn off therespective switch and the ignition.A blown fuse can be recognized by itsmelted wire. Do not replace the fuseuntil the cause of the fault has beenremedied.Some functions are protected byseveral fuses.Fuses may also be inserted withoutexistence of a function.

Vehicle care 157

Fuse extractorA fuse extractor may be located in thefuse box in the engine compartment.

Place the fuse extractor on thevarious types of fuse from the top orside, and withdraw fuse.

158 Vehicle care

Engine compartment fuse box

The fuse box is in the front left of theengine compartment.Disengage the cover, lift it upwardsand remove.After having changed defective fusesclose the fuse box cover and pressuntil it engages.If the fuse box cover is not closedcorrectly, malfunctions may occur.

No. Circuit

1 Starter

2 –

3 Fuel filter, cooling

4 Horn

5 Terminal 30

6 Engine control module,transmission control unit

7 Fog light

8 Engine cooling

9 Engine cooling

10 Vacuum pump

11 Ignition, preheating

12 Headlamp levelling

13 Air conditioning system,terminal 15

14 Transmission control unit

15 High beam right

Vehicle care 159

No. Circuit

16 High beam left

17 Engine control module

18 Engine control module,terminal 15

19 Airbag

20 Engine control module

21 Engine control module,terminal 87

No. Circuit

22 Electrical parking brake

23 Tyre repair kit

No. Circuit

24 Fuel pump

25 ABS

26 Heated rear window

27 ABS

28 Interior fan

29 Cigarette lighter

30 Air conditioning system

31 Front power window, left

32 Front power window, right

33 Mirror heating

34 ABS

35 Airbag

160 Vehicle care

Instrument panel fuse box

The fuse box is behind the storagecompartment in the instrument panel.Open compartment, compress thelocking tabs, fold compartment downand remove.

In right-hand drive vehicles, the fusebox is located behind a cover in theglovebox. Open the glovebox, pullcover upwards and remove.

No. Circuit

1 Rear left door unlocking

2 Display, instrument, telephone

3 Radio

4 Ignition switch, immobiliser

5 Windscreen washer, rearscreen washer

6 Central locking system, tailgate

7 Central locking system

8 Rear right door unlocking

9 Courtesy light

Vehicle care 161

No. Circuit

10 Heated steering wheel

11 –

12 –

13 Rain sensor, interior mirror,outside mirrors

14 –

Load compartment fuse box

The fuse box is on the left side of theload compartment behind a cover.Remove the cover.

Disengage the four retaining lugs andremove the cover.

162 Vehicle care

No. Circuit

1 Adaptive forward lighting

2 –

3 –

4 –

5 –

6 Rear power window, right

7 Adaptive forward lighting

8 Trailer module, Trailer socket

9 Seat, lumbar support, left

10 Rear power window, left

11 Park assist

12 Electrical sunblind

13 –

14 Heated front seats

15 Trailer module

16 Seat, lumbar support, right

17 –

Vehicle toolsToolsVehicles with spare wheel

The jack and the vehicle tools are inthe spare wheel well in the loadcompartment.

Vehicles with tyre repair kit

To open the compartment, disengagethe cover and open it.

Vehicle care 163

The vehicle tools are in the right-handcompartment in the loadcompartment, together with the tyrerepair kit.

Wheels and tyres

Tyre condition, wheel conditionDrive over edges slowly and at rightangles if possible. Driving over sharpedges can cause tyre and wheeldamage. Do not trap tyres on the kerbwhen parking.Regularly check the wheels fordamage. Seek the assistance ofa workshop in the event of damage orunusual wear.

Winter tyresWinter tyres improve driving safety attemperatures below 7 °C and shouldtherefore be fitted on all wheels.In accordance with country-specificregulations, affix the speed sticker inthe driver's field of view.

Tyre designationsE.g. 195/65 R 15 91 H195 = Tyre width, mm65 = Cross-section ratio (tyre

height to tyre width), %

R = Belt type: RadialRF = Type: RunFlat15 = Wheel diameter, inches91 = Load index e.g. 91 is

equivalent to 615 kgH = Speed code letter

Speed code letter:Q = up to 100 mphS = up to 112 mphT = up to 118 mphH = up to 130 mphV = up to 150 mphW = up to 168 mph

Tyre pressureCheck the pressure of cold tyres atleast every 14 days and before anylong journey. Do not forget the sparewheel. This also applies to vehicleswith tyre pressure monitoring system.Unscrew the valve cap.

164 Vehicle care

Tyre pressure 3 189 and on the labelon the front left door frame.The tyre pressure data refers to coldtyres. It applies to summer and wintertyres.Always inflate the spare tyre to thepressure specified for full load.The ECO tyre pressure serves toachieve the smallest amount of fuelconsumption possible.Incorrect tyre pressures will impairsafety, vehicle handling, comfort andfuel economy and will increase tyrewear.

9 Warning

If the pressure is too low, this canresult in considerable tyre warm-up and internal damage, leading totread separation and even to tyreblow-out at high speeds.

If the tyre pressure must be reducedor increased on a vehicle with tyrepressure monitoring system, switchoff ignition.

Tyre deflation detectionsystemThe tyre deflation detection systemcontinually checks the rotation speedof all four tyres.If a tyre loses pressure the controlindicator w illuminates yellow anda warning message is displayed in theDriver Information Center withUplevel-Display. Stop immediatelyand check tyre pressure.Control indicator w 3 88.

System initialisation

After tyre pressure correction orwheel change, the system must beinitiated: Switch on the ignition, pressand hold the DDS button for approx.4 seconds.If the system is ready again,a message is displayed in the DriverInformation Center withUplevel-Display.

Tread depthCheck tread depth at regularintervals.

Vehicle care 165

Tyres should be replaced for safetyreasons at a tread depth of 2-3 mm(4 mm for winter tyres).

The legally permissible minimumtread depth (1.6 mm) has beenreached when the tread has worndown as far as one of the tread wearindicators (TWI). Their position isindicated by markings on thesidewall.If there is more wear at the front thanthe rear, swap round front wheels andrear wheels periodically. Ensure thatthe direction of rotation of the wheelsis the same as before.

Tyres age, even if they are not used.We recommend tyre replacementevery 6 years.

Changing tyre and wheel sizeIf tyres of a different size than thosefitted at the factory are used, it may benecessary to reprogramme thespeedometer as well as the nominaltyre pressure and make other vehiclemodifications.After converting to a different tyresize, have the label with tyrepressures replaced.

9 Warning

Use of unsuitable tyres or wheelsmay lead to accidents and willinvalidate the vehicle typeapproval.

Wheel coversWheel covers and tyres that arefactory approved for the respectivevehicle and comply with all of therelevant wheel and tyre combinationrequirements must be used.

If the wheel covers and tyres used arenot factory approved, the tyres mustnot have a rim protection ridge.Wheel covers must not impair brakecooling.

9 Warning

Use of unsuitable tyres or wheelcovers could lead to suddenpressure loss and therebyaccidents.

Tyre chains

166 Vehicle care

Tyre chains are only permitted on thefront wheels.Always use fine mesh chains that addno more than 10 mm to the tyre treadand the inboard sides (including chainlock).

9 Warning

Damage may lead to tyre blowout.

The use of tyre chains is not permittedon the temporary spare wheel.

Tyre repair kitMinor damage to the tyre tread can berepaired with the tyre repair kit.Do not remove foreign bodies fromthe tyres.Tyre damage exceeding 4 mm or thatis at the tyre's sidewall near the rimcannot be repaired with the tyre repairkit.

9 Warning

Do not drive faster than 50 mph.Do not use for a lengthy period.Steering and handling may beaffected.

If you have a flat tyre:Apply the parking brake and engagefirst gear, reverse gear or P.The tyre repair kit is in the stowagecompartment in the loadcompartment.

To open the compartment, disengagethe cover and open it.

1. Take the sealant bottle andbracket with air hose from theinsert.

Vehicle care 167

2. Detach air hose from bracket andscrew onto sealant bottleconnection.

3. Position the sealant bottle on thebracket. Make sure that the bottledoes not fall.

4. Unscrew valve cap from defectivetyre.

5. Screw tyre inflation hose to valve.6. Screw air hose onto compressor

connection.7. Switch on ignition.

To avoid discharging the battery,we recommend running theengine.

8. Press < button on thecompressor. The tyre is filled withsealant.

9. The compressor pressure gaugebriefly indicates up to 6 bar whilstthe sealant bottle is emptying(approx. 30 seconds). Then thepressure starts to drop.

10. All of the sealant is pumped intothe tyre. Then the tyre is inflated.

11. The prescribed tyre pressureshould be obtained within10 minutes. Tyre pressure3 189. When the correct pressureis obtained, switch off the

168 Vehicle care

compressor by pressing the <button again.If the prescribed tyre pressure isnot obtained within 10 minutes,remove the tyre repair kit. Movethe vehicle one tyre rotation.Reattach the tyre repair kit andcontinue the filling procedure for10 minutes. If the prescribed tyrepressure is still not obtained, thetyre is too badly damaged. Seekthe assistance of a workshop.Release excess tyre pressureusing the ] button.Do not run the compressor longerthan 10 minutes.

12. Push catch on bracket to removesealant bottle from bracket. Screwthe tyre inflation hose to the freeconnection of the sealant bottle.This prevents sealant fromescaping. Stow tyre repair kit inload compartment.

13. Remove any excess sealantusing a cloth.

14. Take the label indicatingmaximum permitted speed fromthe sealant bottle and affix in thedriver's field of view.

15. Continue driving immediately sothat sealant is evenly distributedin the tyre. After driving approx.6 miles (but no more than10 minutes), stop and check tyrepressure. Screw compressor airhose directly onto tyre valve andcompressor when doing this.If tyre pressure is more than1.3 bar, set it to the correct value.Repeat the procedure until thereis no more loss of pressure.If the tyre pressure has fallenbelow 1.3 bar, the vehicle mustnot be used. Seek the assistanceof a workshop.

16. Stow away tyre repair kit in loadcompartment.

NoteThe driving characteristics of therepaired tyre is severely affected,therefore have this tyre replaced.If unusual noise is heard or thecompressor becomes hot, turncompressor off for at least30 minutes.The built-in safety valve opens ata pressure of 7 bar.Note the expiry date of the kit. Afterthis date its sealing capability is nolonger guaranteed. Pay attention tostorage information on sealantbottle.Replace the used sealant bottle.Dispose of the bottle as prescribedby applicable laws.The compressor and sealant can beused from approx. -30 °C.The adapters supplied can be usedto pump up other items e.g.footballs, air mattresses, inflatabledinghies etc. They are located on theunderside of the compressor. Toremove, screw on compressor airhose and withdraw adapter.

Vehicle care 169

Wheel changingSome vehicles are equipped witha tyre repair kit instead of a sparewheel 3 166.Make the following preparations andobserve the following information:■ Park the vehicle on a level, firm and

non-skid surface. The front wheelsmust be in the straight-aheadposition.

■ Apply the parking brake andengage first gear, reverse gear orP.

■ Remove the spare wheel 3 171.■ Never change more than one wheel

at once.■ Use the jack only to change wheels

in case of puncture, not forseasonal winter or summer tyrechange.

■ If the ground on which the vehicleis standing is soft, a solid board(max. 0.4 inches thick) should beplaced under the jack.

■ No people or animals may be in thevehicle when it is jacked-up.

■ Never crawl under a jacked-upvehicle.

■ Do not start the vehicle when it israised on the jack.

■ Before screwing in the wheel bolts,clean them and lightly coat thetaper of each wheel bolt withcommercially available grease.

1. Pull off the wheel cover with thehook. Vehicle tools 3 162.For wheel covers with visiblewheel bolts: The cover can remainon the wheel. Do not remove theretaining rings on the wheel bolts.

Alloy wheels: Disengage wheelbolt caps with a screwdriver andremove. To protect the wheel,place a soft cloth between thescrewdriver and the alloy wheel.

2. Install the wheel wrench ensuringthat it locates securely and looseneach wheel bolt by half a turn.

170 Vehicle care

3. Ensure the jack is positionedcorrectly with the vehicle jackingpoints.Lifting the vehicle onto a liftingplatform:

Position the rear arm of the liftingplatform at the underbody.

Position the front arm of the liftingplatform at the underbody.

Vehicle care 171

4. Set the jack to the necessaryheight. Position it directly belowthe jacking point in a manner thatprevents it from slipping.

Attach jack handle and with thejack correctly aligned rotatehandle until wheel is clear of theground.

5. Unscrew the wheel bolts.6. Change the wheel.7. Screw on the wheel bolts.8. Lower vehicle.

9. Install the wheel wrench ensuringthat it locates securely and tighteneach bolt in a crosswisesequence. Tightening torque is110 Nm.

10. Align the valve hole in the wheelcover with the tyre valve beforeinstalling.Install wheel bolt caps.

11. Stow the replaced wheel 3 171and the vehicle tools 3 162.

12. Check the tyre pressure of theinstalled tyre and also the wheelbolt torque as soon as possible.

Have the defective tyre renewed orrepaired.

Spare wheelSome vehicles are equipped witha tyre repair kit instead of a sparewheel.The spare wheel can be classified asa temporary spare wheel dependingon the size compared to the othermounted wheels and countryregulations.

The spare wheel has a steel rim.The use of a spare wheel that issmaller than the other wheels or incombination with winter tyres couldaffect driveability. Have the defectivetyre replaced as soon as possible.

The spare wheel is located in the loadcompartment beneath the floorcovering. It is secured with a wing nut.The spare wheel well is not designedfor all permissible tyre sizes. Ifa wheel wider than the spare wheelhas to be stowed in the loadcompartment, it needs to be securedwith a strap or, depending on theversion, with an extension bar.

172 Vehicle care

Storing a replaced wheel in theload compartment using a strapUse the strap placed in the tool box.Vehicle tools 3 162.■ Position the wheel on the load

compartment floor close to one sidewall of the load compartment.

■ Stick the loop end of the strapthrough the front lashing eye of theaccording side.

■ Stick the hook end of the strapthrough the loop and pull it until thestrap is fastened securely to thelashing eye.

■ Insert the strap through the spokesof the wheel as shown in theillustration.

■ Mount the hook to the rear lashingeye.

■ Tighten the strap and secure itusing the buckle.

Storing a replaced wheel in thespare wheel well using anextension barUse the extension bar placed in thetool box. Vehicle tools 3 162.■ Turn the wing nut anticlockwise and

remove temporary spare wheel.

■ Take the extension bar from thetool box and screw it on the bolt.

■ Store the damaged wheel andsecure it by turning the wing nutclockwise.

The floor cover can be placed on theprojecting wheel.Remove the extension bar beforefitting the spare wheel in the well afterrenewing or repairing the defectivewheel.

Vehicle care 173

9 Warning

Storing a jack, a wheel or otherequipment in the loadcompartment could cause injury ifthey are not fixed properly. Duringa sudden stop or a collision, looseequipment could strike someone.Store jack and tools always in therespective storage compartmentsand secure them by fixing.Place the damaged wheel alwaysin the load compartment securedby the strap or in the spare wheelwell secured by the wing nut.

Temporary spare wheelThe use of the temporary spare wheelcould affect driveability. Have thedefective tyre renewed or repaired assoon as possible.Only mount one temporary sparewheel. Do not drive faster than50 mph. Take curves slowly. Do notuse for a long period of time.Tyre chains 3 165.

Directional tyresFit directional tyres such that they rollin the direction of travel. The rollingdirection is indicated by a symbol(e.g. an arrow) on the sidewall.The following applies to tyres fittedopposing the rolling direction:■ Driveability may be affected. Have

the defective tyre renewed orrepaired as soon as possible.

■ Drive particularly carefully on wetand snow-covered road surfaces.

Jump startingDo not start with quick charger.A vehicle with a discharged batterycan be started using jump leads andthe battery of another vehicle.

9 Warning

Be extremely careful when startingwith jump leads. Any deviationfrom the following instructions canlead to injuries or damage causedby battery explosion or damage tothe electrical systems of bothvehicles.

9 Warning

Avoid contact of the battery witheyes, skin, fabrics and paintedsurfaces. The fluid containssulphuric acid which can causeinjuries and damage in the eventof direct contact.

■ Never expose the battery to nakedflames or sparks.

174 Vehicle care

■ A discharged battery can alreadyfreeze at a temperature of 0 °C.Defrost the frozen battery beforeconnecting jump leads.

■ Wear eye protection and protectiveclothing when handling a battery.

■ Use a booster battery with thesame voltage (12 volts). Its capacity(Ah) must not be much less thanthat of the discharged battery.

■ Use jump leads with insulatedterminals and a cross section of atleast 16 mm2 (25 mm2 for dieselengines).

■ Do not disconnect the dischargedbattery from the vehicle.

■ Switch off all unnecessary electricalconsumers.

■ Do not lean over the battery duringjump starting.

■ Do not allow the terminals of onelead to touch those of the otherlead.

■ The vehicles must not come intocontact with each other during thejump starting process.

■ Apply the parking brake,transmission in neutral, automatictransmission in P.

Lead connection order:1. Connect the red lead to the

positive terminal of the boosterbattery.

2. Connect the other end of the redlead to the positive terminal of thedischarged battery.

3. Connect the black lead to thenegative terminal of the boosterbattery.

4. Connect the other end of the blacklead to a vehicle grounding point,such as the engine block or anengine mounting bolt. Connect asfar away from the dischargedbattery as possible, however atleast 2 ft.

Route the leads so that they cannotcatch on rotating parts in the enginecompartment.To start the engine:1. Start the engine of the vehicle

providing the jump.2. After 5 minutes, start the other

engine. Start attempts should bemade for no longer than15 seconds at an interval of1 minute.

3. Allow both engines to idle forapprox. 3 minutes with the leadsconnected.

Vehicle care 175

4. Switch on electrical consumers(e.g. headlights, heated rearwindow) of the vehicle receivingthe jump start.

5. Reverse above sequence exactlywhen removing leads.

TowingTowing the vehicle

Disengage cap at bottom and removedownwards.The towing eye is stowed with thevehicle tools 3 162.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.Attach a tow rope – or better still a towrod – to the towing eye.The towing eye must only be used fortowing and not for recovering thevehicle.

Caution

Activate the child lock in both reardoors if the rear seats areoccupied. Child locks 3 24.

176 Vehicle care

Switch on ignition to release steeringwheel lock and to permit operation ofbrake lights, horn and windscreenwiper.Transmission in neutral.Switch on the hazard warningflashers on both vehicles.

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

When the engine is not running,considerably more force is needed tobrake and steer.To prevent the entry of exhaust gasesfrom the towing vehicle, switch on theair recirculation and close thewindows.Vehicles with automatic transmission:The vehicle must be towed facingforwards, not faster than 50 mph norfurther than 60 miles. In all othercases and when the transmission isdefective, the front axle must beraised off the ground.

Seek the assistance of a workshop.After towing, unscrew the towing eye.Insert cap at the bottom and closecap.

Towing another vehicle

Disengage the cap at the bottom andremove downwards.The towing eye is stowed with thevehicle tools 3 162.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.The lashing eye at the rearunderneath the vehicle must never beused as a towing eye.Attach a tow rope – or even bettera tow bar – to the towing eye.The towing eye must only be used fortowing and not for recoveringa vehicle.Switch on the hazard warningflashers on both vehicles.

Vehicle care 177

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

After towing, unscrew the towing eye.Insert cap at the bottom and engagecap.

Appearance careExterior careLocksThe locks are lubricated at the factoryusing a high quality lock cylindergrease. Use de-icing agent only whenabsolutely necessary, as this hasa degreasing effect and impairs lockfunction. After using de-icing agent,have the locks regreased bya workshop.

WashingThe paintwork of your vehicle isexposed to environmental influences.Wash and wax your vehicle regularly.When using automatic vehiclewashes, select a programme thatincludes waxing.Bird droppings, dead insects, resin,pollen and the like should be cleanedoff immediately, as they containaggressive constituents which cancause paint damage.If using a vehicle wash, comply withthe vehicle wash manufacturer'sinstructions. The windscreen wipers

and rear window wiper must beswitched off. Remove antenna andexternal accessories such as roofracks etc.If you wash your vehicle by hand,make sure that the insides of thewheel housings are also thoroughlyrinsed out.Clean edges and folds on openeddoors and the bonnet as well as theareas they cover.Have the door hinges of all doorsgreased by a workshop.Do not clean the engine compartmentwith a steam-jet or high-pressure jetcleaner.Thoroughly rinse and leather-off thevehicle. Rinse leather frequently. Useseparate leathers for painted andglass surfaces: remnants of wax onthe windows will impair vision.

Exterior lightsHeadlight and other light covers aremade of plastic. Do not use anyabrasive or caustic agents, do not usean ice scraper, and do not clean themdry.

178 Vehicle care

Polishing and waxingWax the vehicle regularly (at thelatest when water no longer beads).Otherwise, the paintwork will dry out.Polishing is necessary only if the painthas become dull or if solid depositshave become attached to it.Paintwork polish with silicone formsa protective film, making waxingunnecessary.Plastic body parts must not be treatedwith wax or polishing agents.

Windows and windscreen wiperbladesUse a soft lint-free cloth or chamoisleather together with window cleanerand insect remover.When cleaning the rear window,make sure the heating element insideis not damaged.For mechanical removal of ice, usea sharp-edged ice scraper. Press thescraper firmly against the glass sothat no dirt can get under it andscratch the glass.

Clean smearing wiper blades witha soft cloth and window cleaner.

MoonroofNever clean with solvents or abrasiveagents, fuels, aggressive media (e.g.paint cleaner, acetone-containingsolutions etc.), acidic or highlyalkaline media or abrasive pads. Donot apply wax or polishing agents tothe middle part of the moonroof.

Wheels and tyresDo not use high-pressure jetcleaners.Clean rims with a pH-neutral wheelcleaner.Rims are painted and can be treatedwith the same agents as the body.

Paintwork damageRectify minor paintwork damage witha touch-up pen before rust forms.Have more extensive damage or rustareas repaired by a workshop.

UnderbodySome areas of the vehicle underbodyhave a PVC undercoating while othercritical areas have a durableprotective wax coating.After the underbody is washed, checkthe underbody and have it waxed ifnecessary.Bitumen/rubber materials coulddamage the PVC coating. Haveunderbody work carried out bya workshop.Before and after winter, wash theunderbody and have the protectivewax coating checked.

Towing equipmentDo not clean the coupling ball bar witha steam-jet or high-pressure jetcleaner.

Interior careInterior and upholsteryOnly clean the vehicle interior,including the instrument panel fasciaand panelling, with a dry cloth orinterior cleaner.

Vehicle care 179

The instrument panel should only becleaned using a soft damp cloth.Clean fabric upholstery witha vacuum cleaner and brush.Remove stains with an upholsterycleaner.Clean seat belts with lukewarm wateror interior cleaner.

Caution

Close Velcro fasteners as openVelcro fasteners on clothing coulddamage seat upholstery.The same applies to clothing withsharp-edged objects, like zips orbelts or studded jeans.

Plastic and rubber partsPlastic and rubber parts can becleaned with the same cleaner asused to clean the body. Use interiorcleaner if necessary. Do not use anyother agent. Avoid solvents and petrolin particular. Do not use high-pressure jet cleaners.

180 Service and maintenance

Service andmaintenance

General information ................... 180Recommended fluids, lubricantsand parts .................................... 181

General informationService informationIn order to ensure economical andsafe vehicle operation and tomaintain the value of your vehicle, itis of vital importance that allmaintenance work is carried out at theproper intervals as specified.The detailed, up-to-date serviceschedule for your vehicle is availableat the workshop.Service display 3 82.

European service intervalsMaintenance of your vehicle isrequired every 20,000 miles or after1 year, whichever occurs first, unlessotherwise indicated in the servicedisplay.The European service intervals arevalid for the following countries:Andorra, Austria, Belgium, Bosnia-Herzegovina, Bulgaria, Croatia,Cyprus, Czech Republic, Denmark,Estonia, Finland, France, Germany,Greece, Greenland, Hungary,Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Macedonia,Malta, Montenegro, Netherlands,Norway, Poland, Portugal, Romania,Serbia, Slovakia, Slovenia, Spain,Sweden, Switzerland, UnitedKingdom.Service display 3 82.

International service intervalsMaintenance of your vehicle isrequired every 10,000 miles or after1 year, whichever occurs first, unlessotherwise indicated in the servicedisplay.The international service intervals arevalid for the countries which are notlisted in the European serviceintervals.Service display 3 82.

ConfirmationsConfirmation of service is recorded inthe Service and Warranty Booklet.The date and mileage is completedwith the stamp and signature of theservicing workshop.

Service and maintenance 181

Make sure that the Service andWarranty Booklet is completedcorrectly as continuous proof ofservice is essential if any warranty orgoodwill claims are to be met, and isalso a benefit when selling thevehicle.

Service interval with remainingengine oil life durationThe service interval is based onseveral parameters depending onusage.The service display lets you knowwhen to change the engine oil.Service display 3 82.

Recommended fluids,lubricants and partsRecommended fluids andlubricantsOnly use products that have beentested and approved. Damageresulting from the use of non-approved materials will not becovered by the warranty.

9 Warning

Operating materials arehazardous and could bepoisonous. Handle with care. Payattention to information given onthe containers.

Engine oilEngine oil is identified by its qualityand its viscosity. Quality is moreimportant than viscosity whenselecting which engine oil to use. Theoil quality ensures e.g. enginecleanliness, wear protection and oil

aging control, whereas viscositygrade gives information on the oil'sthickness over a temperature range.The new engine oil qualityDexos 2 TM is the newest oil qualityand combines gasoline and dieselperformance. If it is unavailable,engine oils of other listed qualitieshave to be used.

Engine oil quality for Europeanservice schedulesDexos 2 TM = All petrol and diesel

engines

Alternative qualities if Dexos 2 TM isnot available:GM-LL-A-025 = Petrol enginesGM-LL-B-025 = Diesel engines

Engine oil quality for internationalservice schedulesDexos 2 TM = All petrol and diesel

engines

Alternative qualities if Dexos 2 TM isnot available:GM-LL-A-025 = Petrol enginesGM-LL-B-025 = Diesel engines

182 Service and maintenance

Alternative qualities if GM-LL-A-025or GM-LL-B-025 are not available:ACEA-A3/B3 orA3/B4

= Petrol engines

ACEA-A3/B4 = Diesel engineswithout DieselParticle Filter(DPF)

ACEA-C3 = Diesel engineswith DPF

Topping up engine oilEngine oils of different manufacturersand brands can be mixed as long asthey comply with the required engineoil quality and viscosity.If engine oil of the required quality isnot available, a maximum of 1 litre ofACEA C3 grade may be used (onlyonce between each oil change). Theviscosity should be of one of thebelow listed viscosity grades.Use of engine oil with onlyACEA A1/B1 or only A5/B5 quality isexplicitly prohibited, since it cancause long-term engine damageunder certain operating conditions.

Additional engine oil additivesThe use of additional engine oiladditives could cause damage andinvalidate the warranty.

Engine oil viscosity gradesUse only engine oil viscosity gradesSAE 5W-30 or 5W-40, 0W-30 or0W-40.The SAE viscosity grade givesinformation of the thickness of the oil.Multigrade oil is indicated by twofigures. The first figure, followed bya W, indicates the low temperatureviscosity and the second figure thehigh temperature viscosity. Pleaseselect the approriate viscosity gradedepending on your minimum ambienttemperature.■ down to -25 °C:

SAE 5W-30 or SAE 5W-40■ below -25 °C:

SAE 0W-30 or SAE 0W-40

Coolant and antifreezeUse only silicate-free long life coolant(LLC) antifreeze.

The system is factory filled withcoolant designed for excellentcorrosion protection and frostprotection down to approx. -28 °C.This concentration should bemaintained all year round. The use ofadditional coolant additives thatintend to give additional corrosionprotection or seal against minor leakscan cause function problems. Liabilityfor consequences resulting from theuse of additional coolant additives willbe rejected.

Brake and clutch fluidUse only brake fluid which exceedsDOT4 requirements.Over time, brake fluid absorbsmoisture which will reduce brakingeffectiveness. The brake fluid shouldtherefore be replaced at the specifiedinterval.Brake fluid should be stored ina sealed container to avoid waterabsorption.Ensure brake fluid does not becomecontaminated.

Technical data 183

Technical data

Vehicle identification .................. 183Vehicle data ............................... 185

Vehicle identificationVehicle Identification Number

The Vehicle Identification Number isstamped on the identification plateand on the floor pan, under the floorcovering, visible under a cover.

The Vehicle Identification Numbermay be embossed on the instrumentpanel visible through the windscreen.

184 Technical data

Identification plate

The identification plate is located onthe rear right-hand door frame.

Information on identification label:1 = Manufacturer2 = Type approval number3 = Vehicle Identification Number4 = Permissible gross vehicle

weight rating5 = Permissible gross train weight6 = Maximum permissible front axle

load7 = Maximum permissible rear axle

load8 = Vehicle-specific or country

specific data

The combined total of front and rearaxle loads must not exceed thepermissible gross vehicle weight. Forexample, if the front axle is bearing itsmaximum permissible load, the rearaxle can only bear a load that is equalto the gross vehicle weight minus thefront axle load.The technical data is determined inaccordance with EuropeanCommunity standards. We reservethe right to make modifications.Specifications in the vehicledocuments always have priority overthose given in this manual.

Technical data 185

Vehicle dataEngine dataSales designation 1.4 1.4 1.4 1.3 1.7Engine identifier code A14XER A14NEL A14NET A13DTC A17DT

Number of cylinders 4 4 4 4 4

Piston displacement [cm3] 1398 1364 1364 1248 1686

Engine power [kW] 74 88 103 55 74

at rpm 6000 4800-6000 4900-6000 4000 4000

Torque [Nm] 130 175 200 180 260

at rpm 4000 1750-4800 1850-4900 1750 1700-2550

Fuel type Petrol Petrol Petrol Diesel Diesel

Octane rating RON

recommended 95 95 95

possible 98 98 98

possible 91 91 91

Oil consumption [l/1000 km] 0.6 0.6 0.6 0.6 0.6

186 Technical data

PerformanceEngine A14XER A14NEL A14NET A13DTC A17DT

Maximum speed1) [mph]

Manual transmission 2) 2) 2) 2) –

Automatic transmission – – – – 2)

Fuel consumption - CO2-emissionsTo convert l/100 km into mpg, divide 282 by number of litres/100 km.Manual transmission / automatic transmission.

Engine A14XER A14NEL A14NET A13DTC A17DT

urban [l/100 km] 3)/– 3)/– 3)/– 3)/– –/3)

extra-urban [l/100 km] 3)/– 3)/– 3)/– 3)/– –/3)

total [l/100 km] 3)/– 3)/– 3)/– 3)/– –/3)

CO2 [g/km] 3)/– 3)/– 3)/– 3)/– –/3)

1) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipmentcould reduce the specified maximum speed of the vehicle.

2) Value was not available at time of printing.3) Value was not available at time of printing.

Technical data 187

Vehicle weightKerb weight, basic model without any optional equipment

Engine Manual transmission Automatic transmission

without/with air conditioning[kg]

A14XER 1360/1375 –

A14NEL 1393/1408 –

A14NET 1393/1408 –

A13DTC 1437/1452 –

A17DT – 1503/1518

Kerb weight, basic model with all optional equipmentEngine Manual transmission Automatic transmission

without/with air conditioning[kg]

A14XER –/1571 –

A14NEL –/1613 –

A14NET –/1613 –

A13DTC –/1613 –

A17DT – –/1701

188 Technical data

Vehicle dimensions

Length [mm] 4288

Width without exterior mirrors [mm] 1812

Width with two exterior mirrors [mm] 1992

Height (without antenna) [mm] 1615

Length of load compartment floor [mm] 815

Length of load compartment with folded rear seats [mm] 1642

Load compartment width [mm] 1038

Load compartment height [mm] 803

Height of load compartment opening 791

Wheelbase [mm] 2644

Turning circle diameter [m] 11.1

Technical data 189

CapacitiesEngine oilEngine A14XER A14NEL A14NET A13DTC A17DT

including Filter [l] 4.0 4.0 4.0 3.2 5.4

between MIN and MAX [l] 1.0 1.0 1.0 1.0 1.0

Fuel tankPetrol/diesel, nominal capacity [l] 54

Tyre pressuresComfort with up to 3 people ECO with up to 3 people With full load

Engine Tyres front rear front rear front rear[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A14XER 195/65 R15, 230/2.3 (33) 210/2.1 (30) 280/2.8 (41) 260/2.6 (38) 250/2.5 (36) 320/3.2 (46)

205/55 R16,

225/45 R17

225/40 R184) 230/2.3 (33) 210/2.1 (30) – – 250/2.5 (36) 320/3.2 (46)

4) With reduced steering angle.

190 Technical data

Comfort with up to 3 people ECO with up to 3 people With full loadEngine Tyres front rear front rear front rear

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A14NEL 195/65 R15, 230/2.3 (33) 210/2.1 (30) 280/2.8 (41) 260/2.6 (38) 250/2.5 (36) 320/3.2 (46)

205/55 R16,

225/45 R17

225/40 R184) 250/2.5 (36) 230/2.3 (33) – – 270/2.7 (39) 320/3.2 (46)

A14NET 205/55 R16, 230/2.3 (33) 210/2.1 (30) 280/2.8 (41) 260/2.6 (38) 250/2.5 (36) 320/3.2 (46)

225/45 R17

225/40 R184) 250/2.5 (36) 230/2.3 (33) – – 270/2.7 (39) 320/3.2 (46)

A13DTC 195/65 R15, 230/2.3 (33) 210/2.1 (30) 280/2.8 (41) 260/2.6 (38) 250/2.5 (36) 320/3.2 (46)

205/55 R16,

225/45 R17

225/40 R184) 230/2.3 (33) 210/2.1 (30) – – 250/2.5 (36) 320/3.2 (46)

4) With reduced steering angle.

Technical data 191

Comfort with up to 3 people ECO with up to 3 people With full loadEngine Tyres front rear front rear front rear

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A17DT 195/65 R155), 250/2.5 (36) 230/2.3 (33) 300/3.0 (43) 280/2.8 (41) 270/2.7 (39) 320/3.2 (46)

205/55 R16,

225/45 R17

225/40 R184) 270/2.7 (39) 250/2.5 (36) – – 280/2.8 (41) 320/3.2 (46)

All Temporary sparewheel

420/4.2 (61) 420/4.2 (61) – – 420/4.2 (61) 420/4.2 (61)

5) Only permitted in combination with weight reduction package.4) With reduced steering angle.

192 Technical data

Towing hitch installation dimensions

Customer information 193

Customerinformation

Vehicle data recording andprivacy ....................................... 193

Vehicle data recordingand privacyEvent data recordersThe vehicle has a number ofsophisticated systems that monitorand control several vehicle data.Some data may be stored duringregular operation to facilitate repair ofdetected malfunctions, other data isstored only in a crash or near crashevent by systems commonly calledevent data recorders (EDR).The systems may record data aboutthe condition of the vehicle and how itwas operated (e.g. engine speed,brake application, seat belt usage).To read this data special equipmentand access to the vehicle is required.This will take place when the vehicleis serviced in a workshop. Some datais electronically fed into GM globaldiagnostic systems. Themanufacturer will not accessinformation about a crash event orshare it with others except

■ with the consent of the vehicleowner or, if the vehicle is leased,with the consent of the lessee,

■ in response to an official request ofpolice or similar government office,

■ as part of the manufacturer’sdefense in case of legalproceedings,

■ as required by law.In addition, the manufacturer may usethe collected or received data■ for the manufacturer's research

needs,■ to make it available for research

needs where appropriateconfidentiality is maintained andneed is shown,

■ to share summary data which is nottied to a specific vehicle with otherorganisations for researchpurposes.

194

Index AAccessories and vehicle

modifications .......................... 141Adaptive brake light.................... 129Adaptive forward lighting ..........

.................................. 89, 108, 150Adjustable air vents ................... 119Airbag and belt tensioners ........... 85Airbag deactivation ................ 47, 86Airbag system .............................. 45Air conditioning regular

operation ................................ 120Air conditioning system .............. 115Air intake .................................... 120Air quality sensor........................ 116Alert.............................................. 97Antifreeze................................... 144Antilock brake system ................ 129Antilock brake system (ABS) ....... 87Anti-theft alarm system ................ 25Anti-theft locking system .............. 25Armrest................................... 36, 40Armrest storage ........................... 57Automatic anti-dazzle .................. 28Automatic light control ............... 105Automatic locking .................. 23, 90Automatic transmission ............. 125Auxiliary heater........................... 119

BBattery ....................................... 146Battery discharge protection ...... 113Battery, jump starting.................. 173Belts.............................................. 41Bicycle rack.................................. 57Bonnet ....................................... 142Brake and clutch system ............. 86Brake assist ............................... 131Brake fluid .................................. 145Brakes ............................... 129, 145Bulb replacement ....................... 147

CCapacities .................................. 189Car Pass ...................................... 18Catalytic converter ..................... 124Central locking system ................ 20Centre console lighting .............. 112Changing tyre and wheel size . . . 165Charging system .......................... 86Child locks ................................... 24Child restraint installation

locations ................................... 50Child restraint systems ................ 49Cleaning the vehicle................... 177Climate control ............................. 15Climate control, service.............. 120Clock............................................. 78

195

Code............................................. 94Control indicators.......................... 82Control of the vehicle ................. 121Controls in steering wheel............ 74Convex shape .............................. 27Coolant....................................... 144Coolant temperature gauge.......... 81Cruise control ...................... 90, 133Cupholders .................................. 54Curtain airbag system .................. 47

DDanger, Warnings and Cautions . . . 3Dashboard.................................... 11Daytime running light............ 90, 105Deflation detection system........... 88Diesel fuel system bleeding ....... 146Diesel particle filter............... 88, 123Door open .................................... 90Driver Information Center............. 90Driving characteristics and

towing tips .............................. 138

EElectric adjustment ...................... 27Electrical parking brake................ 87Electrical parking brake fault........ 87Electronic climate control

system .................................... 116Electronic driving programmes . . 127

Electronic Stability Control.......... 132Electronic Stability Control and

Traction Control system............ 88Electronic Stability Control off....... 88End-of-life vehicle recovery ....... 142Engine compartment fuse box ... 158Engine coolant ........................... 144Engine coolant temperature

gauge ....................................... 81Engine data ............................... 185Engine exhaust .......................... 123Engine oil ................................... 143Engine oil pressure ...................... 89Entry lighting .............................. 112Event data recorders.................. 193Exhaust gases............................ 123Exit lighting ................................ 112Exterior care .............................. 177Exterior light ................................. 89Exterior lighting ............................ 12Exterior mirrors............................. 27

FFault ........................................... 127First aid kit ................................... 71Fixed air vents ........................... 119Flex-Fix system............................ 57Fog light ....................................... 90Fog lights............................ 109, 152Folding ......................................... 27

Folding tray .................................. 70Front airbag system ..................... 45Front fog lights ........................... 109Front storage................................ 56Fuel consumption - CO2-

Emissions ....................... 138, 186Fuel for diesel engines .............. 136Fuel for petrol engines ............... 136Fuel gauge ................................... 81Fuse box..................................... 158Fuses ......................................... 156

GGauges......................................... 80General information ................... 138Glovebox ..................................... 54Graphic-Info-Display, Colour-

Info-Display .............................. 92

HHalogen headlights .................... 147Hand brake................................. 130Hazard warning flashers ............ 108Headlight flash ........................... 106Headlight range adjustment ...... 106Headlights................................... 106Headlights when driving abroad 107Head restraint adjustment ............. 8Head restraints ............................ 32Heated ......................................... 27

196

Heated rear window ..................... 30Heated steering wheel ................. 75Heating ........................................ 38Heating and ventilation system . 114High beam ........................... 89, 106High beam assist........................ 108Hill start assist ........................... 131Horn ....................................... 13, 75

IIdentification plate ..................... 184Ignition switch positions ............. 122Immobiliser ............................ 26, 89Instrument panel fuse box ......... 160Instrument panel illumination ..... 156Instrument panel illumination

control .................................... 110Instrument panel overview ........... 11Interior care ............................... 178Interior lights ...................... 111, 155Interior mirrors.............................. 28Interruption of power supply ...... 127Introduction .................................... 3ISOFIX child restraint systems .... 53

JJump starting ............................. 173

KKeys ............................................. 18

LLashing eyes ............................... 69Light covers, misted.................... 110Lighting....................................... 105Lighting features......................... 112Light switch ................................ 105Load compartment ................ 24, 66Load compartment cover ............. 67Load compartment fuse box ...... 161Loading information ..................... 72Low fuel ....................................... 89

MMalfunction indicator light ............ 86Manual anti-dazzle ...................... 28Manual mode ............................. 126Manual transmission .................. 128Manual windows .......................... 28Memorised settings...................... 20Messages..................................... 94Mirror adjustment ........................... 8Mirrors.................................... 27, 28Misted light covers ..................... 110Moonroof ..................................... 31

NNew vehicle running-in .............. 121Number plate light ..................... 155

OOctane rating.............................. 185Odometer ..................................... 80Oil............................................... 143Oil pressure.................................. 89Outside temperature .................... 78Overrun cut-off ........................... 122

PParking ................................ 17, 123Parking assist ............................ 134Parking brake ............................ 130Parking lights ............................. 110Particulate filter........................... 123Performance .............................. 186Performing work ........................ 142Personalisation............................. 99Pollen filter ................................. 120Power outlets ............................... 79Power windows ............................ 28Preheating ................................... 88

QQuickheat................................... 119

RRadio remote control ................... 19Reading lights ............................ 111Rear carrier system...................... 57Rear doors ................................... 24

197

Rear floor storage cover .............. 68Rear fog light ............................... 90Rear fog lights ........................... 109Rear seats ................................... 38Rear storage................................. 67Rear window wiper/washer .......... 77Recommended fluids and

lubricants ................................ 181Reduced engine power................ 89Refuelling ................................... 137Remote control............................. 19Reversing lights ......................... 110Roof rack ..................................... 71

SSafety belts................................... 41Safety net .................................... 69Seat adjustment ....................... 6, 34Seat belt ........................................ 8Seat belt reminder ....................... 85Seat belts ..................................... 41Seat heating................................. 38Seat position ................................ 33Selector lever ............................. 125Service ............................... 120, 180Service display ............................ 82Service information .................... 180Service vehicle soon .................... 86Side airbag system ...................... 46Side turn signal lights ................ 155

Spare wheel ............................... 171Speedometer ............................... 80Starting off ................................... 16Starting the engine .................... 122Steering wheel adjustment ...... 9, 74Steering wheel controls ............... 74Steering wheel, heated................. 75Sunglasses storage ..................... 56Sunvisor lights ........................... 111Sun visors .................................... 30Symbols ......................................... 4

TTachometer ................................. 81Tailgate......................................... 24Tail lights ................................... 153Technical data............................ 185Three-point seat belt .................... 42Tools .......................................... 162Top-tether fastening eyes ............ 53Towing another vehicle ............. 176Towing a trailer........................... 139Towing eye................................. 175Towing hitch installation

dimensions ............................. 192Towing the vehicle ..................... 175Traction Control system ............. 131Traction Control system off........... 88Trailer stability assist ................. 139Trailer towing ............................. 139

Transmission ............................... 15Transmission display ................. 125Tread depth ............................... 164Trip computer .............................. 98Trip odometer .............................. 80Tunnel detection......................... 105Turn and lane-change signals ... 109Turn signal ................................... 85Tyre chains ................................ 165Tyre changing............................. 169Tyre deflation detection system . 164Tyre designations ...................... 163Tyre pressure ............................ 163Tyre pressures ........................... 189Tyre repair kit ............................. 166Tyres and wheel size, changing. 165

UUltrasonic parking assist .............. 88Underseat storage ....................... 56Upholstery, cleaning................... 178Upshift.......................................... 87Using this manual .......................... 3

VVariable effort steering................. 87Vehicle dimensions .................... 188Vehicle Identification Number .... 183Vehicle messages ....................... 94Vehicle personalisation ............... 99

198

Vehicle specific data ...................... 3Vehicle storage........................... 141Vehicle unlocking ........................... 6Vehicle weight ........................... 187Ventilation................................... 114

WWarning chimes ........................... 97Warning triangle .......................... 70Washer and wiper systems ......... 13Washer fluid ............................... 145Washing the vehicle................... 177Welcome lighting........................ 112Wheel changing ......................... 169Wheel covers ............................. 165Wheels and tyres ....................... 163Windows....................................... 28Windscreen wiper/washer ........... 76Winter tyres ............................... 163Wiper blade replacement .......... 147