Variable Valve Timing

VARIABBLE VALVE TIMING

PRESENTED BYUTSAV PODDAR

HRISIKESH BHASKARMAHIDUL HAQUE KHAMAR

WHAT IS VVT? Basic Theory After multivalve technology became standard in engine design, Variable Valve Timing became the next step to enhance engine output, power and torque. As you know, valves activate the breathing of engine. The timing of breathing, that is, the timing of air intake and exhaust, is controlled by the shape and phase angle of cams. To optimise the breathing, engine requires different valve timing at different speed. When the revolution increases, the duration of intake and exhaust stroke decreases so that fresh air becomes not fast enough to enter the combustion chamber, while the exhaust becomes not fast enough to leave the combustion chamber. Therefore, the best solution is to open the inlet valves earlier and close the exhaust valves later. In other words, the Overlapping between intake period and exhaust period should be increased as revolution increases.With Variable Valve Timing, power and torque can be optimised across a wide rpm band.

The VVT system is designed to control the intake camshaft with in a range of 50°(of Crankshaft Angle ) to provide valve timing i.e. optimally suited to the engine condition .This improves the torque in all the speed ranges as well as fuel economy ,and reducing exhaust emissions

This system controls the intake camshaft valve timing so as to obtain balance between the engine output, fuel consumption & emission control performance. The actual intake side valve timing is feed back by means of the camshaft position sensor for constant control to the target valve timing

TYPES OF VVT There are two types of variable valve timingA. Cam changing VVTB. Cam phasing VVTCAM CHANGING VVT Cam changing VVT uses different cam profiles to lift the valves depending on

engine load and speed. One common system uses two rocker arms for normal operation on its two

intake valves, with a third, higher profile, rocker arm between the other two arms. At engine speeds above 5000 to 6000 rpm, the engine ECU activates an oil pressure controlled pin that locks the three rocker arms together. The center rocker arm follows a larger and more aggressive profile, transferring its movement to the intake valves which now open further and for longer.

When engine speeds fall below the threshold speed, oil pressure is removed from the pin and a spring deactivates the pin. The rocker arms are no longer locked together and the valves are controlled by the less aggressive outer lobes

Stage 1 (low speed) : both intake and exhaust valves are in slow configuration. Stage 2 (medium speed) : fast intake configuration + slow exhaust

configuration. Stage 3 (high speed) : both intake and exhaust valves are in fast configuration. Advantage: Powerful at top end Disadvantage: 2 or 3 stages only, non-continuous; no much improvement to

torque; complex Who use it ? Honda VTEC, Mitsubishi MIVEC, Nissan Neo VVL.

CAM PHASING VVT Cam phasing VVT is the simplest, cheapest and most

commonly used mechanism at this moment. it varies the valve timing by shifting the phase angle of

camshafts. For example, at high speed, the inlet camshaft will be rotated in advance by 30° so to enable earlier intake. This movement is controlled by engine management system according to need, and actuated by hydraulic valve gears

IT cannot vary the duration of valve opening. It just allows earlier or later valve opening. Earlier open results in earlier close, of course. It also cannot vary the valve lift, unlike cam changing VVT

Advantage: Cheap and simple, continuous VVT improves torque delivery across the whole rev range.

Disadvantage: Lack of variable lift and variable valve opening duration, thus less top end power than Camchanging VVT.

Audi V8 inlet, BMW Double Vanos inlet,Ferrari 360 Modena exhaust, Ford Puma 1.7 Zetec SE inlet, Jaguar AJV6, Lamborghini Diablo SV engine inlet, , Porsche Variocam inlet, 3stage discrete

3) Cam-Changing + Cam- Phasing VVTCombining camchanging VVT and camphasing VVT could satisfy the requirement of both top end Power and flexibility throughout the whole rev range, but it is inevitably more complex. At the time of writing, only Toyota and Porsche have such designs.

CONSTRUCTION:-

The Variable Valve Timing (VVT) system includes ECM OCV VVT controller

• The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature.

• The ECM controls the OCV, based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control.This is how the target intake valve timing is verified by the ECM.

The ECM optimizes the valve timing using the VVT system to control the intake camshaft. The VVT system includes the ECM, the OCV and the VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

OPERATIONThe camshaft timing oil control valve selects the path according to the advance, retard or hold signal from the ECM .The VVT-i controller rotates the intake camshaft in the timing advance or retard position or holds it according to the position where the oil pressure is applied.

• In proportion to the engine speed, intake air volume throttle position and water temperature, the ECM calculates optimal valve timing under each driving condition & controls the camshaft timing oil control valve. In addition ECM uses signal from the camshaft position sensor & the crankshaft position sensor to detect the actual valve timing, thus performing feedback control to achieve the target valve timing

ADVANTAGES of vvt-i• Improved torque &

output• Battery & fuel

economy• Reduced nitrogen

oxide &• hydrocarbon

emissions

Advantages of Variable Valve Engine

0

20

40

60

80

100

120

140

160

0 1000 2000 3000 4000 5000 6000 7000 8000

Engine Speed (rpm)

Bra

ke T

orq

ue

(N*m

)Convential Engine

Varable Valve Engine

Applications of VVT-iVariable Valve Types and Common

Manufacturers

ValvetronicOffers continuously variable valve timing and

valve lift on the intake cam only. Relies on amount of valve lift to throttle engine

BMW

VANOSVaries the timing of the valves by moving the

position of the camshafts in relation to the drive gear.

BMW

VTEC Utilizes two camshaft profiles and electronically selects between the profiles Honda

VarioCam Varies intake timing by adjusting the tension of a cam chain Porche

AVCS/AVLS

AVCS - varies timing (phase) with hydraulic pressure

AVLS - Varies duration, timing and lift by switching between two different sets of cam lobes

SubaruMitsubishi MIVEC

– similar to AVLS

ACKNOLEDGEMENT

Last but not the least, a special word of thanks to the teachers and staff for their ever ready help and guidance without which this task would not be possible:Prof. Amitava Datta

REFERENCES:-

•Different Types of VVT. 2005. 3 May 2007. http://www.autozine.org/technical_school/engine/vvt_2.htm

Wikipedia: Variable Valve Timing. 2007. 1 May 2007.<http://en.wikipedia.org/wiki/Variable_valve_timing

Honda Engines. 2007. 2 May 2007.<http://www.honda-engines-eu.com/en/images/249.gif >

Prof. Dr. Peter Walzer. Technology Highlights and R and D Activities. 2002 http://www.fev.com/data/documents/spectrum20.pdf

THANK YOU!!