1. AptX Low Latency Avantree Clipper Pro is a Bluetooth audio receiver incorporating the latest “aptX low latency” technology, for CD-like quality sound and with virtually no audio delay. Ideal for games, watching TV and movies without lip sync delay. To take advantage of the better performance offered by APTX low latency codec, the other device must also support the same codec (Such as Avantree’s Saturn Pro, Priva II, Leaf, etc). If the transmitter only supports the normal AptX codec, or the SBC one, these codecs will be used instead. 2. Product overview & basic operation Basic operation 3. What’s in the box? A. Avantree Clipper Pro B. Avantree 3.5mm audio splitter *1 C. 3.5mm audio cable *1 D. Micro USB charging cable *1 E. User manual & Quick user guide 4. Pairing and connecting 4.1. Connecting to a mobile phone/tablet Step 1. Ensure Clipper Pro is off. Step 2. Set Clipper Pro to PAIRING MODE - Press and hold MFB for 7 seconds until the LED flashes BLUE and RED alternately and you hear “pairing”. Step 3. Activate Bluetooth on your phone/tablet and select “ Avantree Clipper Pro” , LED flash once per 5 seconds once connected, and you hear “connected”. Reconnect: Whenever you turn Clipper Pro on again, it will automatically reconnect to your phone. 4.2. Connecting to a Bluetooth transmitter Step 1. Ensure Clipper Pro is off. Step 2. Set Clipper Pro to PAIRING MODE - Press and hold MFB for 7 seconds until the LED flashes BLUE and RED alternately and you hear “pairing”. Step 3. Set your Bluetooth transmitter to PAIRING MODE**. Step 4. Keep both devices close and wait for 5-30 seconds. Once connected, LEDs on both devices will slow down and you hear “connected”. Step 4. Connect Clipper Pro to the second Bluetooth device as above. Step 5. Once connected, restart Clipper Pro and the first paired device. It will then automatically reconnect to the two devices simultaneously. Note: Once disconnected over 10 minutes, Clipper Pro will automatically power itself off. 5. How to reset to factory default setting? Step 1. Turn on the Clipper Pro Step 2. Press and hold the V+ and V- button for 7 seconds Step 3. The Blue and Red LED will flashes twice then power off at the same time **PARING MODE: Discoverable mode for Bluetooth device, normally the LED blinks quickly or flashes between two colors alternately. 4.3. Connecting to two Bluetooth devices simultaneously Step 1. Connect the first Bluetooth device as above. Then turn off Clipper Pro. Step 2. Turn off the bluetooth on the first paired device. (If it is a transmitter, turn it off) Step 3. Set Clipper Pro to PAIRING MODE again – Press and hold MFB for 6 seconds until the LED flashes BLUE and RED alternately. 6. LED indications 3.5 mm Audio jack LED indicator Multi-function button (MFB) Micro USB port Microphone Volume up (Next track) Volume down (Previous track) Dispose of the packaging and this product in accordance with the latest provisions. Dispose of the packaging and this product in accordance with the latest provisions. Charge from USB charger Charge from PC www.avantree.com Z-PKMN-AS7L-V5 For a Beer Experience Audio delay by transmier type - Transmitter support - The audio delay will be aptX Low Latency codec Around 40ms aptX codec Around 180ms SBC codec (most standard Bluetooth audio) Around 250ms 7. Charging When the LED flashes RED, you should recharge the device. Please remove the micro-USB protector and charge it. It normally takes around 2 hours to fully charge the battery. The LED will stay RED when charging and will turn off when charging is complete. Charging Requirement You can connect Clipper Pro via the supplied micro USB cable to your own USB chargers (wall charger/travel charger/car charger, etc.) with 5V/500mA-1A or PC USB port. It’s ok to use most mobile phone chargers on the market. 8. Product Specifications • BT version: 4.2 • BT profile: A2DP, AVRCP, HFP, HSP • Audio codec: aptX Low Latency, aptX, SBC • Operational range: Class II, up to 10 meters • Working time: Up to 6 hours • Standby time: 100 hours • Charging time: 2 hours • Product weight: approx. 15g • Product size: 50.5*26*18mm Note: The talk and standby times may vary when used with different mobile phones or other devices and also defendent upon different usage styles, settings and operating environment. 9. Declaration of Conformity This device complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC ID: BTHS-AS7 To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. Power on LED flashes BLUE for 2 seconds Power off LED flashes RED for 2 seconds Pairing mode Connected LED flashes BLUE once every 10 seconds Disconnected Low battery Charging LED stays RED Fully charged Restore to default setting LED flashes BLUE and RED together twice (appears PINK) LED flashes BLUE and RED alternately LED flashes BLUE twice every 10 seconds Red LED turns off LED flashes RED once every 30 seconds Note: Some functions may not work when used with different mobile phones or other Bluetooth devices. Button MFB V+ V– Function Operation Power on/off Hold MFB for 2-3 seconds to turn Clipper Pro ON/OFF, you will hear “ Welcome to Avantree” / “ Goodbye” Enter pairing mode From off mode, press & hold for 7 seconds until LED flashes BLUE and RED fast, you will hear “pairing”. Answer/End a call Press MFB once when a call is incoming or in progress Reject a call Press & hold MFB for 2 seconds when a call is incoming Last number redial Double click MFB Play/Pause Press once MFB when streaming music Press V+ once Next track Press and hold Volume up Volume down Previous track Press V- once Press and hold Press and hold V+ and V- together for 7 seconds, the LED flashes BLUE and RED together ( appears PINK) V+& V- Restore to default settings Connect Pair Once connected, the LEDs on both devices will slow down. Use your existing headphones to listen to the TV wirelessly Enjoy 3 Set Clipper pro to pairing mode Set transmitter to PAIRING MODE* Keep them close & wait Hold MFB 6S, LED flashes BLUE and RED alternately Bluetooth Settings Bluetooth Devices Avantree Clipper Pro Connect Pair From off, hold for 6s, LED flashes BLUE and RED alternately Activate Bluetooth, search and select “Clipper Pro” to connect. Hold MFB 6S Enjoy 3 Stream music wirelessly A. B. C. D. E. Dual Link - 6 - - 4 - - 9 - - 10 - - 11 - - 2 - - 1 - - 5 - - 7 - - 8 - - 3 - Contents 1. AptX Low Latency 2. Product overview & basic operation 3. What’s in the box? 4. Pairing and connecting 4.1. Connecting to a mobile phone/tablet 4.2. Connecting to a Bluetooth transmitter 4.3. Connecting to two Bluetooth devices simultaneously 5. How to reset to factory default setting? 6. LED indications 7. Charging 8. Product Specifications 1 11 10 9 7-8 8 6-7 5-6 5 2 4 Status LED indicator For a Beer Experience www.avantree.com User Manual Wireless Receiver for Headphones Clipper Pro www.avantree.com User Manual Wireless Receiver for Headphones Clipper Pro Voice Dial (Siri) Press V+ and V- together once Low battery When connected, RED LED flash once per 5s. When disconnected, RED LED flash once per 2s. Any questions? Contact: [email protected] Self-service Support: • More FAQs on support.avantree.com • 100+ Step by step video Guide – youtube.com/avantree/playlists Telephone Support (Mon-Fri): • USA / CANADA +1 800 232 2078 (EN, PST 9am-5pm) • EU / Asia telephone No. refer to http: //www.avantree.com/contact-us