USB DAQ Product

USB DAQ ProductUSB DAQ Product

Κώστας ΓρηγορίουΚώστας ΓρηγορίουSales EngineerSales EngineerΙούνιος 26Ιούνιος 26,, 2007 2007

USB-enabled Device ForecastUSB-enabled Device Forecast With continued adoption

of USB in the consumer electronics and communications segments, and the rapid introduction of high-speed USB into PCs and PC peripherals, the total market for USB-enabled devices will experience 18.3% annual growth between 2003 and 2008.

Why USB-based DA&C Module?Why USB-based DA&C Module?

Standard I/F on most new computers Becoming a new industry standard Easy Installation: hot-swappable, plug-and-play Connect up to 127 devices to a single USB host Compact size, economic packaging Plugable terminal blocks for easy connection One cable supplies both power & signal connection. No

external power or battery is required (may <5m) High-performance 480Mbps transmission Isolated shielded box & direct I/O connection from sensors,

useful for portable AP & noisy environment

What’s Advantech Design What’s Advantech Design Concept ?Concept ?

Keep the same specification and driver as our existed PCI-bus DA&C cards, for R&D easy to develop and diagnostic the system.

– The same H/W and S/W between development and run-time

– Save time and effort on simulation and trouble shooting

– Portable and plug-and-play

USB Data Acquisition SeriesUSB Data Acquisition SeriesUSB-4711

USB-4718

USB-4716

• 12-bit, 100kS/s• 16 AI/ 2AO• 8DI/ 8DO TTL • 16-bit counter x 1• High Speed USB 2.0 • No need for external power

12-bit, 100kS/s Multifunction Module

16-bit, 100kS/s Multifunction Module

8-Ch Thermocouple Input Module

• 16-bit, 100kS/s• 16 AI/ 2AO • 8DI/ 8DO TTL• 16-bit counter x 1• USB 2.0• No need for external power

• 8-Ch thermocouple• J,R,K,S,T,B,E type• 3000VDC isolation• USB 2.0• No need for external power

USB-4711USB-4711- 100kS/s, 12-bit Multifunction Module

• Targeting

• Positioning

• Segmentation• Hand-carry data acquisition applications

• Embedded System For Harsh Environment

• Portable multi-function device

• Lab users

• Laptop Application

• Features• Support High-Speed USB 2.0

• 16AI / 2AO / 8DI / 8DO Channels

• No need for external power supply

• Removable screw terminal block

145 mm

30 mm

100mm

Weight: 150g

100 mm

16 S.E. Channels AI

8-Ch DI/ 8-Ch DO

2 Channels AO

USB-4711USB-4711- 100kS/s, 12-bit Multifunction Module

• 12 bits resolution

• 100kS/s sampling rate

• 1K FIFO memory

• External trigger source applicable with GATE control

• Auto Calibration

• 0~5, 0~10, +/-5, +/-10 V multiple output range

• 5mA driving capability

TTL Compatible

1 Counter

Fast USB 2.0 Bus SupportFast USB 2.0 Bus Support•480Mbps Data Rate

USB-4711 can operate at up to 480Mbps to fulfill the fast data transfer and realize the high speed data acquisition

•No need for external powerBecause of the low power consumption, USB-4711 can work under the internal USB 500mA power supply, which means users don’t have to worry about the power source even when they are in the outdoors.

•Hot swapable and P&P functionUsers can install or remove USB-4711 without reboot or shut down there system. Give them the quick and convenient operation

USB 2.0

Thoughtful mechanism design for your on-to-go application

Removable screw terminal for easy wiring

You can just switch the screw terminals for various kind of wiring diagrams without any re-wiring efforts.

Pre-marked pin assignment index makes your wiring work quick and straight.

Removable terminal P/N: 1652610101

LED indicatorLED indicator gives you the guide of the current status of the device.

Skid-proof rubber feet4 rubber feet let your device stands firm and soundly

LED StatusLED Status DescriptionDescription

OnOn Ready for workReady for work

OffOff Not ready for workNot ready for work

Slow blinkingSlow blinking Device installationDevice installation

Fast BlinkingFast Blinking WorkingWorking

On-module pin assignment index

Installation of USB-4711Installation of USB-4711 Support both USB 2.0 and USB 1.1

– USB 1.1 speed: 12M bits/s– USB 2.0 speed: 480M bits/s

Note: The AI can only up to 2kS/s when using USB 1.1Note: The AI can only up to 2kS/s when using USB 1.1

Operation of USB-4711 (I)Operation of USB-4711 (I) Fully support the same driver with DA&C card

(ADSAPI32 DLL, ActiveDAQ & LabVIEW)

Operation of USB-4711 (II)Operation of USB-4711 (II)

Easily update the firmware of USB-module in dedicated Utility for upgrading.

Target ApplicationsTarget Applications Automated test and measurement Data logging Temperature measurement Environmental monitoring and control Process monitoring and control Quality control Laboratory automation Portable data acquisition Production test Electronics test Semiconductor test Telecommunications Calibration Research and development

WaveScan Utility WaveScan Utility – Setting– Setting

WaveScan Utility WaveScan Utility – – Waveform ScanWaveform Scan

WaveScan Utility WaveScan Utility – Storage– Storage

WaveScan Utility WaveScan Utility – Scaling– Scaling

Overview

DAQ wherever you likeDAQ wherever you like (portable DAQ solution without (portable DAQ solution without programming)programming)

USB-4711USB-4711: 100kS/s Multifunction Module (USB-based, no : 100kS/s Multifunction Module (USB-based, no external power is needed) external power is needed)

Wavescan utilityWavescan utility: to display the acquired signals, also can save : to display the acquired signals, also can save to HDD for further analysisto HDD for further analysis

Wavescan utility

Thank You