Oct 19, 2015
Quicknote
Rev Date File Name
1.1 21/05/2010 Upgrading the SST-PB3-CLX Profibus scanner firmwares
Description
Product concerned: SST-PB3-CLX-RLL (SAP Number 1120160018) Product version: all Environment: SST Configuration Tool V3.11.4.0 or upper Related documents: SST-PB3-CLX-RLL User Manual V1.2 or upper Restriction: None
Upgrading the SST-PB3-CLX Profibus scanner firmwares
Summary: This document will explain you why there are 2 firmwares versions for the new BradCommunications SST Profibus module, how to check them and how to upgrade them if needed. We strongly recommend reading this document from start to the end in order to get enough information before upgrading.
Upgrading the SST-PB3-CLX Profibus scanner firmwares V1.1 Page 2 of 6
1- Why there are 2 firmwares ?
The SST-PB3-CLX is a new architecture. It has been developed with better technology using 2 processors. This is why there are 2 firmwares:
- The pfbclx.ss3 file which manages the Profibus communication - The pfbclx.ss4 file which manages the communication between the backplane and the
module.
2- How to check the firmwares versions ?
=> The pfbclx.ss4 To know the Backplane firmware you need to look at the display of the module during the Boot phase, it will show the Firmware version (ex.: 7.33). => The pfbclx.ss3 To know the Profibus Firmware you can use the SST Configuration Tool or the HyperTerminal tool (which is also the upgrading utility). From the SST Configuration Tool: Click on Connect button then on Firmware version
Profibus Firmware Version
Upgrading the SST-PB3-CLX Profibus scanner firmwares V1.1 Page 3 of 6
From the HyperTerminal connection:
Create a connection with HyperTerminal as follows :
Cycle power on the CLX rack. (If you can't, INHIBIT the SST module from RSLogix and put it OFFLINE from SST configuration tool, then take it out and insert it again in the rack). While the SYS LED is red after powering up, hit several times the exclamation mark (!) from your keyboard until getting the following result:
To get the Profibus Firmware version, enter the command ver pfbclx.ss3 as shown in the next picture (Help command shows all the available options)
Serial Null Modem Cable
Upgrading the SST-PB3-CLX Profibus scanner firmwares V1.1 Page 4 of 6
3- How to upgrade the firmwares versions with HyperTerminal ?
=> The pfbclx.ss3 Start a HyperTerminal connection as indicated above (Part 2 From the
HyperTerminal connection) To upgrade the firmware, use the command Ry pfbclx.ss3 to initiate a Ymodem send.
Once the series of C starts send the file using the Ymodem send.
0711
Upgrading the SST-PB3-CLX Profibus scanner firmwares V1.1 Page 5 of 6
Ymodem send
Upgrading the SST-PB3-CLX Profibus scanner firmwares V1.1 Page 6 of 6
Check it out with the command ver pfbclx.ss3.Then enters the command run
pfbclx.ss3 to exit System Configuration mode and start up. => The pfbclx.ss4
Start a HyperTerminal connection as indicated above (Part 2 From the HyperTerminal connection)
To upgrade the firmware, use the command Burn. Once the series of C starts, send
the file using the Ymodem send as indicated above (Part 3 Ymodem send), but this time you have to choose the file pfbclx.ss4
Please wait for the message then cycle
Cycle power on the CLX rack power on the CLX rack. (If you can't, take the SST module out and insert it again in the rack)