UNTERLIEGT NICHT DEM ÄNDERUNGSDIENST ...* Prozessbedingte Abweichungen der Abisoliermaße, z.B. durch Schweißen (Längung, Einlegetiefe), sind zulässig und auszugleichen process-related
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
3a) mechanisch / mechanical Mantel (M) und Schirm (S) von Kabel "D"nach Tabelle abisolieren.Insulate coat (M) and shielding (S) ofcable "D" acc. to table.
4a) mechanisch / mechanical Stützhülse "G" auf Mantel "D" aufschieben. Orientierung der Stützhülse beachten.Schirmgeflecht muss flach anliegen und darf nicht zerstört werden.Abstand nach Tabelle. Move carrying tube "G" on insulate coat "D". Observe orientation of carrying tube. Make sure the braided shielding is flat and is not destroyed.For spacing see table.
* Prozessbedingte Abweichungen der Abisoliermaße, z.B. durch Schweißen (Längung, Einlegetiefe), sind zulässig und auszugleichen process-related differences of stripping dimensions e.g. by welding (elongation, insertion depth) are allowed and have to corrected
3b) automatisiert / automated Mantel (M) von Kabel "D" nach Tabelleabisolieren.Insulate coat (M) of cable "D" acc. to table.
4b) automatisiert / automated Stützhülse "G" auf Mantel "D" aufschieben. Orientierung der Stützhülse beachten.Schirmgeflecht muss flach anliegen und darf nicht zerstört werden.Abstand nach Tabelle. Move carrying tube "G" on insulate coat "D". Observe orientation of carrying tube.Make sure the braided shielding is flat and is not destroyed.For spacing see table.
* Prozessbedingte Abweichungen der Abisoliermaße, z.B. durch Schweißen (Längung, Einlegetiefe), sind zulässig und auszugleichen process-related differences of stripping dimensions e.g. by welding (elongation, insertion depth) are allowed and have to corrected
5a) mechanisch / mechanical Schirmgeflecht gleichmäßig über Stützhülse "G" umlegen.Überlappung min. 70%. Nicht auskämmen. Move the braided shielding equally over carrying tube "G".Overlap min. 70%. Do not comb out the wire.
D G
spacing
G
overlap min. 70%
900
900
NUR ZUR INFORMATIONUNTERLIEGT NICHT DEM ÄNDERUNGSDIENST
5b) automatisiert / automated Schirmgeflecht gleichmäßig über Stützhülse "G" umlegen.Überlappung min. 70%. Nicht auskämmen. Move the braided shielding equally over carrying tube "G".Overlap min. 70%. Do not comb out the wire.
6) Isolation (D) nach Tabelle abisolieren.Remove insulation (D) acc. to table. Alle Schirmlitzen müssen min. einen Abstand von 8mm zum Kabelinnenleiter aufweisen.All shielding braids must have a minimum clearance of 8mm to cable center braid.
* Prozessbedingte Abweichungen der Abisoliermaße, z.B. durch Schweißen (Längung, Einlegetiefe), sind zulässig und auszugleichen process-related differences of stripping dimensions e.g. by welding (elongation, insertion depth) are allowed and have to corrected
G
overlap min. 70%
D dielectric cut
900
900
900
NUR ZUR INFORMATIONUNTERLIEGT NICHT DEM ÄNDERUNGSDIENST
8)Vormontierte Kabelbaugruppe bis Anschlag in Außenleiter "B" einschieben. C-Ring muss einrasten. Verrastung kontrollieren! Insert pre-installed cable assembly into the outer conductor "B" until stop.C-ring "H" must engage. Control catch!
925-05931-301-001Alternativ / alternative production: 925-06287-301-001 in Verbindung mit Kontaktaufnahme 925-05931-301-001in conjunction with Contacting 925-05931-301-001f
* Einlegen von rechts / engaged from right** Einlegen von vorn / engaged from front1) Werte gelten nur fuer Leitungen nach LV216-2 Tabelle A.2 Value only apply to wire acc. to LV216-2 table A.22) Werte gelten nur fuer Leitungen nach LV216-2 Tabelle A.3 Value only apply to wire acc. to LV216-2 table A.3
Werkzeugempfehlungtool recommendation
Y
Y 5:1
Stützhülse "G"carrying tube "G" Außenleiter "B"
outer conductor "B"
C-Ringc-ring
B
900
900
NUR ZUR INFORMATIONUNTERLIEGT NICHT DEM ÄNDERUNGSDIENST
* Einlegen von rechts / engaged from right** Einlegen von vorn / engaged from front
9) Außenleiter "B" crimpen. Die Stützhülse muss vollständig im Crimpbereich liegen.Auf die Position der Stützhülse "G" und des Außenleiters "B" muss geachtet werden.Crimpdetails sind der Tabelle zu entnehmen. Crimp outer conductor "B". Ensure that carrying tube is completely inside the crimping area.Be aware of the position of carrying tube "G" and outer conductor "B". For crimping details see table.
900
900 900 900
900
NUR ZUR INFORMATIONUNTERLIEGT NICHT DEM ÄNDERUNGSDIENST
11)Gecrimpte Kabelbaugruppen in Gehäuse "A" bis zum Anschlag einschieben.Kabelbaugruppen müssen verrasten. Verrastung kontrollieren. Insert crimped cable assemblies into housing "A" until stop.Cable assembly must engage. Control catch.
10)Litzen dürfen nicht überstehen! Überstand entfernen! Shielding wires must not protrude! Remove protrusion!
A
900
900
NUR ZUR INFORMATIONUNTERLIEGT NICHT DEM ÄNDERUNGSDIENST
12)2 Dichtungen "E" in Gehäuse "A" schieben.2 Verschlusskappen "F" auf Gehäuse "A" schieben und einrasten.Orientierung der Abdeckkappen beachten: flache Seiten sind gegeneinander gerichtet.Sekundärsicherung drücken. Slide 2 seals "E" into housing "A".Push 2 sealing caps "F" onto housing "A" and snap them in.Note orientation of the caps: the flat sides are directed against to each other.Press secondary locking.
100% elektrische Prüfung100% electrical and insulating checking100% Durchgangsprüfung100% continuity testSpannungsfestigkeit 2.7 kVDC zwischen Hochvoltkontakten,Hochvoltkontakte zu HVIL Kontakten und zu Außenleiter.Insulation resistance 2.7 kVDC between high voltage contacts,high voltage contact and HVIL contacts and outer contact.Kodierungsabfragecoding query100% Sichten der Dichtung100% screening for seal Elektromagnetische Verträglichkeit (EMV) [HV-System] geprüft nach LV 215 PG50Electromagnetic compatibility (EMC) [HV system] tested according to LV 215 PG50
100% Elektrische PrüfungSpannungsfestigkeit (Leiter und Schirm)min. 2.7 kVDCIsolationswiderstand (Leiter und Schirm) >200 MOhm / 1000 VDC100% electrical testelectric strength (conductor and shielding)min. 2.7 kVDCinsulation resistance (conductor and shielding) >200 MOhm / 1000 VDC
general tolerance removed Abdeckkappe in 2) changed to Verschlusskappe >150mm in 2) changed to min. 350mm tolerance ±0.5 in 3) placed in bracket -> (±0.5) text "remove shielding foil completely" for 3) inserted mechanical and automated variation for step 3, 4 and 5 inserted shielding foil in pic. and text "remove shielding foil" in 4a) removed tolerance ±0.6 in 4) placed in bracket -> (±0.6) overlapping length of braided schielding shown in pic. of step 5 to 8 shortened tolerance ±0.5 in 6) placed in bracket -> (±0.5) stripping cut insulation in 6) changed to dielectric cut tolerance 36±0.5 in 7) changed to 36+1/-0.5 angle deviation ±3° placed in bracket -> (±3°) row position for 35mm² and 16mm² in table at 7) switched. tool recommendation inserted text "be aware of position..." in 9) inserted excess shielding wires in 9), 10) and 11) removed. tolerance CB ±0.1 changed to ±0.2 tolerance CH ±0.2 changed to ±0.1 min. tensile strength for: 16mm² - 250 -> 150 25mm² - 450 -> 300 35mm² - 520 -> 300 sealing caps "G" in 12) corrected to sealing caps "F" 100% electrical test inserted