UNE 2012 350/500 HEAVY WALLTM IR ENTRANCES 1 …sweets.construction.com › swts_content_files › 153 › 710130.pdfBlast Mitigation Product Las and building and saet codes goerning
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
For specific product applications,Consult your Kawneer representative.
Features
• 350 medium stile has 3-1/2" vertical stile, 3-1/2" top and 6-1/2" bottom rail• 500 wide stile has 5" vertical stile, 5" top and 6-1/2" bottom rail• Door is 2" deep• Door has 3/16" wall thickness• Welded corner construction• Single acting• Offset pivot, butt hinges or continuous geared hinge• Surface mounted or concealed closers• MS lock or exit device hardware• Architects Classic push-pulls• Square stops with interior silicone seal for 9/16" (14.3 mm) or 1" (25.4 mm) glazing infills• Adjustable astragal utilizing pile weathering with polymeric fin at meeting stiles• Polymeric bulb weatherstripping in door frames• Permanodic® anodized finishes in seven standard choices• Painted finishes in standard and custom choices
Optional Features
• Numerous push/pull options• Paneline® exit device or Paneline® EL exit device• 3/16" heavy wall frame• Crossrails and 10" Bottom Rail• Square stops with 3MTM VHBTM interior tape for 9/16" (14.3 mm) or 1" (25.4 mm) glazing infills
Product Applications
• 350/500 Heavy WallTM IR provides added strength for schools, institutions, office buildings and other high traffic applications where codes require windborne debris or blast mitigating protection.
LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR.
Metric (SI) conversion figures are included throughout these details for reference.Numbers in parentheses ( ) are millimeters unless otherwise noted.
The following metric (SI) units are found in these details:
m – meter
cm – centimeter
mm – millimeter
s – second
Pa – pascal
MPa – megapascal
Kawneer reserves the right to change configurations without prior notice when deemed necessaryfor product improvement.
#1 MECHANICAL FASTENING is accomplished by attaching a 5/16" (7.9) thick extruded aluminum channel clip to the vertical stile with 1/4"-20 heat strengthened bolts and 3/16" thick steel nut plates for a high strength welding base for attachment horizontal member.
#2 SIGMA* DEEP PENETRATION PLUG WELDS are made top and bottom after the horizontal is properly positioned over the channel clip to help provide the strongest door corner joint currently available.
#3 SIGMA* FILLET WELDS along both top and bottom webs of the rail extrusion complete the welded corner construction.
* An arc welding process known as Shielded Inert Gas Metal Arc (SIGMA) or also known as Metal Inert Gas (MIG).
The Paneline® concealed rod exit device will accommodate variations in door width as shown in the followingillustrations. Sidelites adjacent to Paneline equipped doors not requiring exit devices may be fitted with fixed panelsas detailed below to match the general appearance of the Paneline cross rail.
The Optional Paneline® EL device is designed for electrified access control and is compatible with most key padand card reader systems.
See Hardware Section for complete description of Paneline hardware, including finish of units.
Paneline® uses mortise cylinder in lieu of the normal rim-type.Dummy Paneline units should not use any type of lock.
INTERIOR ELEVATION
PANELINE® EL COMPONENTS
POWER TRANSFERINTERMEDIATE BUTT HINGE
POWER TRANSFERINTERMEDIATE OFFSET PIVOT
ELECTRIC POWER TRANSFER(EPT)
SP 1000 POWER SUPPLY
LOCK STILE TRIM FILLER WIDTHVARIES WITH STILE WIDTH
DOGGING LOCK(TYPICAL)
PIVOT STILE TRIM FILLER WIDTHVARIES WITH DOOR WIDTH
DOOR OPENING WIDTH
4'-0" (1219.2) MAX. - 2'-10 13/32" (873.9) MIN. 3'-0" (914.6) ADA MIN.
NOTE:*IR 501 door frame uses IR 500 door jamb with IR 501 filler, (assembly has not been impact tested).**Concealed Overhead Closer requires Trifab® VG 450 frame, Trifab® VG 450 sub-header, or 1600 Wall System®1 sub-frame.
STANDARD OPTIONAL
Door Sizes Maximum Size:4'-0" x 8'-0" (1219.2 x 2438.4) per leaf8'-0" x 8'-0" (2438.4 x 2438.4) pairs3'-0" x 9'-0" (914.4 x 2743.2) per leaf6'-0" x 9'-0" (1828.8 x 2743.2) pairs
Sizes up to maximum per leaf or pair
Glass Stops Square stops for 9/16" (14.3) infill, interior screw applied glass stop with silicone seal
Square stops for 9/16" (14.3) or 1" (25.4) infill, interior screw applied glass stop with 3M VHB structural tape.
Door Frames IR500 frame = 2-1/2" x 5" (63.5 x 127) - *IR 501 frame = 2-1/2" x 5" (63.5 x 127)- Trifab® VG 450 non-transom or sidelites- Trifab® VG 451 (50.8 x 114.3)- 1600 sub-frame with door jamb adaptors and sub-head
Push-Pulls Architects Classic Hardware: - CO-9 Pull and CP-II Push Bar - CO-9 Pull with Exit Devices - CO-9 Pull with Paneline® Exit Device
Supplied by others
Door Closers Norton 1601 Adjustable or 1601 BFAdjustable Surface Closer with back-check, with or without adjustable hold open
**Concealed Closers- Standard COC with single acting offset arm- LCN 2030, LCN 5030
Hinging Kawneer Top, Bottom and Intermediate offset pivots - Kawneer 4-1/2" x 4" (114.3 x 101.6) Top, Bottom and Intermediate (NRP) Butt Hinge- Continuous Geared Hinge
Locking MS 1850 Deadbolt 3-Point Lock with 4016 Top Bolt and 4056 Bottom Bolt
Exit DeviceHardware
Kawneer 1686 Concealed Exit Device - Kawneer Paneline® Conc. Rod Exit Device- Kawneer Paneline® EL Conc. Rod Exit Device- Falcon HSEC1690 Conc. Rod Exit Device- Jackson 2086 Conc. Rod Exit Device- Jackson 2086 EL Conc. Rod Exit Device- Von Duprin HSEC9947 Conc. Rod Exit Device- Von Duprin XP 98/99 Rim Exit Device
Threshold Kawneer Threshold1/2" x 4-3/8" (12.7 x 111.1)
Weathering Sealair® bulb polymeric weathering in door frames, adjust-able bottom rail sweep with EPDM blade and adjustable astragal utilizing pile weathering with polymeric fin at meeting stiles
4'-0" x 8'-0" (1219.2 x 2438.4) per leaf8'-0" x 8'-0" (2438.4 x 2438.4) pairs3'-0" x 9'-0" (914.4 x 2743.2) per leaf6'-0" x 9'-0" (1828.8 x 2743.2) pairs
± 110 PSF Offset PivotsButt Hinges
Continuous Hinge
1, 2, 3 9/16" (14.3)1" (25.4)
Kawneer 1686Conc. Rod Exit Device
Single 4'-0" x 8'-0" (1219.2 x 2438.4)Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 110 PSF Offset PivotsButt Hinges
Continuous Hinge
1, 2, 3 9/16" (14.3)1" (25.4)
Paneline®
Conc. Rod Exit DeviceSingle 4'-0" x 8'-0" (1219.2 x 2438.4)Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 70 PSF Offset PivotsButt Hinges
Continuous Hinge
1, 2, 3 9/16" (14.3)1" (25.4)
Falcon HSEC 1690Conc. Rod Exit Device
4'-0" x 8'-0" (1219.2 x 2438.4) per leaf8'-0" x 8'-0" (2438.4 x 2438.4) pairs
± 50 PSF Offset PivotsButt Hinges
Continuous Hinge
1, 2, 3 9/16" (14.3)1" (25.4)
3'-0" x 9'-0" (914.4 x 2743.2) per leaf6'-0" x 9'-0" (1828.8 x 2743.2) pairs
± 60 PSF
Jackson 2086Conc. Rod Exit Device
Single 4'-0" x 8'-0" (1219.2 x 2438.4)Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 90 PSF Offset PivotsButt Hinges
Continuous Hinge
1, 2, 3 9/16" (14.3)1" (25.4)
Von Duprin XP 98/99Rim Exit Device
4'-0" x 8'-0" (1219.2 x 2438.4) per leaf8'-0" x 8'-0" (2438.4 x 2438.4) pairs
± 50 PSF Offset PivotsButt Hinges
Continuous Hinge
1, 2, 3 9/16" (14.3)1" (25.4)
Von Duprin HSEC 9947Conc. Rod Exit Device
4'-0" x 8'-0" (1219.2 x 2438.4) per leaf8'-0" x 8'-0" (2438.4 x 2438.4) pairs
± 50 PSF Offset PivotsButt Hinges
Continuous Hinge
1, 2, 3 9/16" (14.3)1" (25.4)
3'-0" x 9'-0" (914.4 x 2743.2) per leaf6'-0" x 9'-0" (1828.8 x 2743.2) pairs
± 60 PSF
Glazing Stop Options:1 - Structural silicone with 0.090 Dupont or Solutia PVB interlayer or 0.090 Dupont Sentry Glas® interlayer.2 - 3M VHB structural tape with 0.090 Dupont or Solutia PVB interlayer or 0.090 Dupont Sentry Glas® interlayer.3 - Dry glazing gasket with 0.090 Dupont Sentry Glas® interlayer, only for 9/16" (14.3) infill with design pressure < or = 90 PSF.