-
8/8/2019 U-SYS WorkSpace UC User Manual
1/227
Chapter 1 System Description
1-1........................................................................
1.1 Introduction to Unified Communication System
1-1.....................................
1.2 Services
1-2..................................................................................................
1.2.1 Overview of Services
1-2.....................................................................1.2.2
Click to Call
1-2....................................................................................
1.2.3 Click to Fax
1-3....................................................................................
1.2.4 Instant Message
1-3.............................................................................
1.2.5 Presence
1-3........................................................................................
1.2.6 Phone Presence
1-4............................................................................
1.2.7 Intelligent Call Route
1-4......................................................................
1.2.8 Remote Office
1-5................................................................................
1.2.9 Unified Message
1-6............................................................................
1.3 Functions
1-6................................................................................................1.3.1
Portal
1-6..............................................................................................
1.3.2 Single Sign On
1-6...............................................................................
1.3.3 Personal Information Management t
1-6..............................................
1.3.4 Address List
1-6...................................................................................
1.3.5 Call Log
1-7..........................................................................................
1.3.6 UC Administration
1-7..........................................................................
1.3.7 Multi-Level Service Management
1-7...................................................
1.3.8 Network Address Translation
1-7.........................................................
1.3.9 Language Support
1-7.........................................................................
1.4 Networking Principles
1-7.............................................................................
1.4.1 Networking Model
1-7..........................................................................
1.4.2 UC Server Group
1-8...........................................................................
1.4.3 Networking Modes
1-10.........................................................................
1.5 Billing System
1-13.........................................................................................
1.5.1 Overview of Billing System
1-13............................................................
1.5.2 Examples of Charging Cases
1-13........................................................
1.6 Technical Specifications
1-14.........................................................................1.6.1
System Capacity
1-14............................................................................
1.6.2 Power Consumption
1-15.......................................................................
Chapter 2 Installation and Configuration of UC Server
2-1...............................
2.1 Installing UC System Software
2-1...............................................................
2.1.1 Configuring System and Connection Data
2-1.....................................
2.1.2 Overview of Software Installation
2-3...................................................
2.1.3 Installing Operating System
2-4...........................................................
2.1.4 Installation of Active Directory
2-9........................................................
2.1.5 Installation of Live Communication Server 2003
2-25............................
-
8/8/2019 U-SYS WorkSpace UC User Manual
2/227
2.1.6 Installing SQL Server 2000
2-37............................................................
2.1.7 Installation of SQL Server 2000 Service Pack 3
2-52............................
2.1.8 Installation of Exchange Server 2003
2-60............................................
2.2 Installation and Configuration of UC Application
2-77....................................
2.2.1 Installing on AD Side
2-77......................................................................
2.2.2 Installation on Portal Side
2-87..............................................................
2.2.3 Deployment and Configuration for Multiple Enterprises
2-94.................
2.3 Deploying UC Service With NAT
2-96............................................................
2.3.1 Installing Certificate in AD
2-96..............................................................
2.3.2 Installing Certificate for Web Server
2-98..............................................
2.3.3 Configuration for LCS Communication
2-100..........................................
Chapter 3 Operation Guide for Administrators
3-1.............................................
3.1 Overview of UC Operations
3-1....................................................................3.1.1
Classification of Administrators
3-1......................................................
3.1.2 UC Service Flow
3-1............................................................................
3.1.3 Operation Preparations of Administrators
3-2......................................
3.2 Operations Performed by Service Administrator
3-5....................................
3.2.1 Logging In to UC Admin
3-5.................................................................
3.2.2 Managing and Configuring Company
3-5............................................
3.2.3 Logging Out of UC Admin
3-10..............................................................
3.3 Operations Performed by Company Administrator
3-10.................................
3.3.1 Logging In to UC Admin
3-10.................................................................
3.3.2 Setting Company Information
3-11........................................................
3.3.3 Setting Department Information
3-12.....................................................
3.3.4 Setting UC Subscriber Information
3-13................................................
Chapter 4 Operation Guide for UC Subscribers
4-1...........................................
4.1 Configuring Client
4-1...................................................................................
4.1.1 Overview of Client Configuration
4-1...................................................
4.1.2 Installing Microsoft XML 3.0 Service Pack 4
4-1..................................
4.1.3 Installing Hotpatch KB832414
4-2........................................................
4.1.4 Setting Trusted Sites
4-2......................................................................
4.1.5 Installing NET Framework
4-2..............................................................
4.1.6 Installing Client Software
4-3...............................................................
4.1.7 Setting Client Software
4-5..................................................................
4.1.8 Setting E-mail
4-6.................................................................................
4.1.9 Setting Language
4-7...........................................................................
4.2 Logging In and Logging Out
4-7...................................................................
4.2.1 Logging In to UC WorkSpace Client
4-7..............................................
4.2.2 Logging Out of UC WorkSpace Client
4-9...........................................
-
8/8/2019 U-SYS WorkSpace UC User Manual
3/227
4.2.3 Meanings of Common Buttons on [Call Manager] of Client
4-10...........
4.3 Setting Display Language on Client
4-14.......................................................
4.4 Click to Dial
4-15............................................................................................
4.4.1 Prerequisites of Click to Dial
4-15..........................................................
4.4.2 Operation Procedure of Click to Dial
4-15..............................................
4.5 Click To E-mail
4-16.......................................................................................
4.5.1 Prerequisites of Click to E-mail
4-16......................................................
4.5.2 Operation Procedure of Click to E-mail
4-16..........................................
4.6 Click To Fax
4-16...........................................................................................
4.6.1 Prerequisites of Click to E-mail
4-16......................................................
4.6.2 Operation Procedure of Click to E-mail
4-16..........................................
4.7 Enhanced Caller ID Display
4-17...................................................................
4.7.1 Prerequisites of Enhanced Caller ID Display
4-17.................................
4.7.2 Operation Procedure of Enhanced Caller ID Display
4-17.....................
4.8 Forwarding Incoming Call
4-18.......................................................................
4.8.1 Prerequisites of Forwarding Incoming Call
4-18....................................
4.8.2 Operation Procedure of Forwarding Incoming Call
4-18........................
4.9 Holding and Retrieving Incoming Call
4-19....................................................
4.9.1 Prerequisites of Holding and Retrieving Incoming Call
4-19..................
4.9.2 Operation Procedure of Holding and Retrieving Incoming
Call 4-19.....
4.10 Holding and Retrieving Outgoing Call
4-20..................................................
4.10.1 Prerequisites of Holding and Retrieving Outgoing Call
4-20................4.10.2 Operation Procedure of Holding and
Retrieving Outgoing Call 4-20...
4.11 Terminating Incoming Call
4-20....................................................................
4.11.1 Prerequisites of Terminating Incoming Call
4-20.................................
4.11.2 Operation Procedure of Terminating Incoming Call
4-21.....................
4.12 Click to Conference
4-21..............................................................................
4.12.1 Prerequisites of Click to Conference
4-21............................................
4.12.2 Operation Procedure of Click to Conference
4-21...............................
4.12.3 Click to Conference Operations
4-22...................................................
4.13 Changing Status of UC Subscriber
4-24......................................................4.14
Operations of Observer
4-25........................................................................
4.15 Sending Instant Messages
4-26...................................................................
4.16 Sending Files or Photos
4-27.......................................................................
4.17 Sharing
4-28.................................................................................................
4.18 Whiteboard
4-30...........................................................................................
4.19 Personal Contacts
4-30................................................................................
4.20 Company Contacts
4-31...............................................................................
4.21 Intelligent Routing by Presence
4-32............................................................
4.21.1 Entering [Intelligent Routing] Window
4-32..........................................
4.21.2 Setting Caller Group Information
4-33.................................................
-
8/8/2019 U-SYS WorkSpace UC User Manual
4/227
4.21.3 Setting Intelligent Routing Policy
4-34.................................................
4.22 Intelligent Call Routing by Time State
4-36..................................................
4.22.1 Entering [Intelligent Routing] Interface
4-36.........................................
4.22.2 Setting Caller Group Information
4-37.................................................
4.22.3 Setting Time State
4-38.......................................................................
4.22.4 Setting Time State Intelligent Call Routing Policy
4-41........................
4.23 Temporary Binding CTD
4-41.......................................................................
4.23.1 Prerequisites of Temporary Binding CTD
4-41....................................
4.23.2 Operation Procedure of Temporary Binding CTD
4-41........................
4.24 Temporary Binding Incoming Call Processing
4-42.....................................
4.24.1 Prerequisites of Temporary Binding Incoming Call
Processing 4-42...
4.24.2 Operation Procedure of Temporary Binding Incoming
CallProcessing
4-42..............................................................................................
4.25 Querying Call Log
4-42.................................................................................
4.25.1 Prerequisites of Querying Call Log
4-42..............................................
4.25.2 Operation Procedure of Querying Call Log
4-42..................................
Chapter 5 Troubleshooting
5-1.............................................................................
5.1 Classification of Fault Causes
5-1................................................................
5.2 Troubleshooting Procedure
5-1....................................................................
5.2.1 Checking Network Communication
5-1................................................
5.2.2 Checking UC Data Configuration for SoftX3000
5-1............................
5.3 Treatment of Network Communication Faults
5-2........................................5.3.1 Server Working
Abnormally After Restarting
5-2.................................
5.3.2 Failure in Logging in to System
5-2......................................................
5.3.3 Failure in Adding Trusted Site
5-3........................................................
5.3.4 Failure in Modifying Password in Login Window
5-3............................
5.3.5 Failure in Logging in to Instant Message Server
5-3............................
5.4 Treatment of Typical Operational Faults
5-4................................................
5.4.1 User Unable to Click to Dial
5-4...........................................................
5.4.2 Failure in Starting UCA Service
5-4.....................................................
5.4.3 Failure in Starting Call Log Service
5-4................................................
5.5 Solution to Typical Operational Problems on UC Client
5-5.........................
Appendix A Configuring UC Service Data in SoftX3000
A-1..............................
A.1 Overview of Configuration
A-1......................................................................
A.1.1 Objective of Configuration
A-1.............................................................
A.1.2 Prerequisites of Configuration
A-1.......................................................
A.1.3 Description of Configuration Relationship
A-1.....................................
A.1.4 Preparations for UC-Related Data
A-1.................................................
A.1.5 Configuration Procedure
A-1................................................................
A.1.6 Relations Between Database Tables
A-2............................................
-
8/8/2019 U-SYS WorkSpace UC User Manual
5/227
A.2 Adding Workstation
A-3................................................................................
A.2.1 MML Commands
A-3...........................................................................
A.2.2 Description of Configuration
A-4..........................................................
A.2.3 Description of Parameters
A-4.............................................................
A.3 Adding UC Group
A-4...................................................................................
A.3.1 MML Commands
A-4...........................................................................
A.3.2 Description of Parameters
A-4.............................................................
A.4 Adding UC User
A-5.....................................................................................
A.4.1 MML Commands
A-5...........................................................................
A.4.2 Description of Parameters
A-5.............................................................
A.5 Configuration Instance
A-7...........................................................................
A.5.1 Instance Data
A-7................................................................................
A.5.2 Steps of Configuration
A-7...................................................................
A.6 Optional Configurations
A-8.........................................................................
A.6.1 Adding UC Caller Group
A-8................................................................
A.6.2 Adding UC Intelligent Call Routing
A-9................................................
A.6.3 Adding UC Week Information
A-11........................................................
A.6.4 Adding UC Date Information
A-13..........................................................
A.6.5 Adding UC Time State Information
A-14................................................
Appendix B Typical Service Flows
B-1................................................................
B.1 CTD Service Flow
B-1..................................................................................
B.2 CTF Service Flow
B-2..................................................................................
B.3 Enhanced Caller ID Service Flow
B-3..........................................................
B.4 CTC Service Flow
B-3..................................................................................
B.5 Temporary Binding (Remote Office) Service Flow
B-4.................................
B.6 Flow of CTD Service of Temporary Binding Service
B-5..............................
B.7 Flow of Call Processing Service of Temporary Binding Service
B-7............
B.8 ICR Service Flow
B-7...................................................................................
B.8.1 ICR Service Setting Flow
B-7...............................................................
B.8.2 ICR Service Processing Flow
B-8........................................................B.9
Unified Message Service Flow
B-9...............................................................
B.9.1 Flow of Instant Message Notification of Unanswered Call
B-9............
B.9.2 Flow of Transferring Voice Mailbox to Email
B-10.................................
Appendix C Acronyms and Abbreviations
C-1....................................................
Index
.................................................................................................................
-
8/8/2019 U-SYS WorkSpace UC User Manual
6/227
HUAWEI
U-SYS WorkSpace Unified Communication System
User Manual
V100R001
-
8/8/2019 U-SYS WorkSpace UC User Manual
7/227
U-SYS WorkSpace Unified Communication System
User Manual
Manual Version T2-010108-20041104-C-1.31
Product Version V100R001
BOM 31014608
Huawei Technologies Co., Ltd. provides customers with
comprehensive technical support
and service. Please feel free to contact our local office or
company headquarters.
Huawei Technologies Co., Ltd.
Address: Administration Building, Huawei Technologies Co.,
Ltd.,
Bantian, Longgang District, Shenzhen, P. R. China
Postal Code: 518129
Website: http://www.huawei.com
Email: [email protected]
http://www.huawei.com/http://www.huawei.com/
-
8/8/2019 U-SYS WorkSpace UC User Manual
8/227
Copyright 2004 Huawei Technologies Co., Ltd.
All Rights Reserved
No part of this manual may be reproduced or transmitted in any
form or by any
means without prior written consent of Huawei Technologies Co.,
Ltd.
Trademarks
, HUAWEI, C&C08, EAST8000, HONET, , ViewPoint, INtess, ETS,
DMC,
TELLIN, InfoLink, Netkey, Quidway, SYNLOCK, Radium,
M900/M1800,
TELESIGHT, Quidview, Musa, Airbridge, Tellwin, Inmedia, VRP,
DOPRA, iTELLIN,
HUAWEI OptiX, C&C08iNET, NETENGINE, OptiX, iSite, U-SYS,
iMUSE, OpenEye,
Lansway, SmartAX, infoX, TopEng are trademarks of Huawei
Technologies Co.,
Ltd.
All other trademarks mentioned in this manual are the property
of their respective
holders.
Notice
The information in this manual is subject to change without
notice. Every effort has
been made in the preparation of this manual to ensure accuracy
of the contents, but
all statements, information, and recommendations in this manual
do not constitute
the warranty of any kind, express or implied.
-
8/8/2019 U-SYS WorkSpace UC User Manual
9/227
About This Manual
Release Notes
This manual applies to U-SYS WorkSpace Unified Communication
System V100R001.
Organization
There are five chapters and three appendixes in the manual.
Chapter 1 System Description profiles the development
background, networking
modes, operation principles and services of UC system.
Chapter 2 Installation and Configuration of UC Server
illustrates the installation
and configuration procedures of UC Server and provides UC Server
operation guide.
Chapter 3 Operation Guide for Administrators provides a guidance
of UC
administrators.
Chapter 4 Operation Guide for UC Subscribers provides a guidance
of UC
subscribers.
Chapter 5 Troubleshooting presents the troubleshooting clues and
methods for
common UC faults.
AppendixA Configuring UC Service Data in SoftX3000 details the
configuration
procedures of most frequently used UC services in the
softswitchSoftX3000.
Appendix B Typical Service Flows specifies the typical and
frequently used service
flows.
Appendix C Acronyms and Abbreviations lists the abbreviations
used in the manual
with the corresponding full expressions.
Intended Audience
The manual is intended for the following readers:
UC system maintenance personnel
NGN technicians
NGN system engineers
-
8/8/2019 U-SYS WorkSpace UC User Manual
10/227
Conventions
The manual uses the following conventions:
I. General conventions
Convention Description
Arial Normal paragraphs are in Arial.
Arial Narrow Warnings, Cautions, Notes and Tips are in Arial
Narrow.Boldface Headings are inBoldface.
II. Command conventions
Convention Description
Boldface The keywords of a command line are inBoldface.
[ ] Items (keywords or arguments) in square brackets [ ] are
optional.
III. GUI conventions
Convention Description
< >Button names are inside angle brackets. For example,
click the button.
[ ]Window names, menu items, data table and field names are
inside squarebrackets. For example, pop up the [New User]
window.
/Multi-level menus are separated by forward slashes. For
example,[File/Create/Folder].
IV. Keyboard operation
Format Description
Press the key with the key name inside angle brackets. For
example,, , , or .
-
8/8/2019 U-SYS WorkSpace UC User Manual
11/227
V. Mouse operation
Action Description
Click Press the left button or right button quickly (left button
by default).
Double Click Press the left button twice continuously and
quickly.
VI. Symbols
Eye-catching symbols are also used in the manual to highlight
the points worthy of
special attention during the operation. They are defined as
follows:
Note, Comment, Tip, Knowhow, Thought: Means a complementary
description.
-
8/8/2019 U-SYS WorkSpace UC User Manual
12/227
User ManualU-SYS WorkSpace Unified Communication System Table of
Contents
Table of Contents
Chapter 1 System
Description.....................................................................................................
1-11.1 Introduction to Unified Communication
System.................................................................
1-11.2 Services
.............................................................................................................................
1-2
1.2.1 Overview of Services
..............................................................................................
1-21.2.2 Click to Call
.............................................................................................................
1-21.2.3 Click to
Fax..............................................................................................................
1-31.2.4 Instant
Message......................................................................................................
1-31.2.5
Presence.................................................................................................................
1-31.2.6 Phone
Presence......................................................................................................
1-41.2.7 Intelligent Call Route
...............................................................................................1-41.2.8
Remote Office
.........................................................................................................
1-51.2.9 Unified
Message......................................................................................................
1-6
1.3 Functions
...........................................................................................................................
1-61.3.1
Portal.......................................................................................................................
1-61.3.2 Single Sign On
........................................................................................................
1-61.3.3 Personal Information Management
t.......................................................................
1-61.3.4 Address
List.............................................................................................................
1-61.3.5 Call Log
...................................................................................................................
1-71.3.6 UC Administration
...................................................................................................1-71.3.7
Multi-Level Service
Management............................................................................
1-71.3.8 Network Address
Translation..................................................................................
1-71.3.9 Language
Support...................................................................................................
1-7
1.4 Networking Principles
........................................................................................................
1-71.4.1 Networking Model
...................................................................................................
1-71.4.2 UC Server
Group.....................................................................................................
1-81.4.3 Networking Modes
................................................................................................1-10
1.5 Billing System
..................................................................................................................
1-131.5.1 Overview of Billing
System....................................................................................
1-131.5.2 Examples of Charging
Cases................................................................................
1-13
1.6 Technical Specifications
..................................................................................................1-141.6.1
System Capacity
...................................................................................................1-141.6.2
Power
Consumption..............................................................................................
1-15
Chapter 2 Installation and Configuration of UC
Server.............................................................
2-12.1 Installing UC System
Software..........................................................................................
2-1
2.1.1 Configuring System and Connection
Data..............................................................
2-12.1.2 Overview of Software
Installation............................................................................
2-32.1.3 Installing Operating System
....................................................................................
2-4
i
-
8/8/2019 U-SYS WorkSpace UC User Manual
13/227
User ManualU-SYS WorkSpace Unified Communication System Table of
Contents
2.1.4 Installation of Active
Directory.................................................................................
2-92.1.5 Installation of Live Communication Server
2003................................................... 2-252.1.6
Installing SQL Server 2000
...................................................................................2-372.1.7
Installation of SQL Server 2000 Service Pack
3................................................... 2-522.1.8
Installation of Exchange Server 2003
...................................................................
2-60
2.2 Installation and Configuration of UC Application
.............................................................
2-772.2.1 Installing on AD
Side.............................................................................................
2-772.2.2 Installation on Portal Side
.....................................................................................2-872.2.3
Deployment and Configuration for Multiple Enterprises
....................................... 2-94
2.3 Deploying UC Service With
NAT.....................................................................................2-962.3.1
Installing Certificate in
AD.....................................................................................
2-962.3.2 Installing Certificate for Web
Server......................................................................
2-982.3.3 Configuration for LCS Communication
...............................................................
2-100
Chapter 3 Operation Guide for Administrators
..........................................................................
3-13.1 Overview of UC
Operations...............................................................................................3-1
3.1.1 Classification of Administrators
...............................................................................
3-13.1.2 UC Service
Flow......................................................................................................3-13.1.3
Operation Preparations of
Administrators...............................................................
3-2
3.2 Operations Performed by Service Administrator
...............................................................
3-53.2.1 Logging In to UC
Admin..........................................................................................3-53.2.2
Managing and Configuring Company
.....................................................................
3-53.2.3 Logging Out of UC Admin
.....................................................................................3-10
3.3 Operations Performed by Company
Administrator..........................................................
3-103.3.1 Logging In to UC
Admin........................................................................................3-103.3.2
Setting Company
Information................................................................................3-113.3.3
Setting Department Information
............................................................................
3-123.3.4 Setting UC Subscriber
Information........................................................................3-13
Chapter 4 Operation Guide for UC
Subscribers.........................................................................
4-14.1 Configuring Client
..............................................................................................................
4-1
4.1.1 Overview of Client
Configuration.............................................................................
4-14.1.2 Installing XML
Patches............................................................................................4-14.1.3
Setting Trusted
Sites...............................................................................................
4-24.1.4 Setting Interface
Language.....................................................................................4-24.1.5
Downloading and Installing Client
Software............................................................
4-24.1.6 Setting Client
Software............................................................................................
4-4
4.2 Logging In and Logging Out
..............................................................................................4-44.2.1
Logging In to UC Workstation
.................................................................................4-44.2.2
Logging Out of UC Workstation
..............................................................................
4-64.2.3 Logging In to UC
Client...........................................................................................4-74.2.4
Meanings of Common Buttons on Client
................................................................
4-84.2.5 Logging Out of UC Client
......................................................................................
4-134.2.6 Modifying Subscriber
Password............................................................................4-13
ii
-
8/8/2019 U-SYS WorkSpace UC User Manual
14/227
User ManualU-SYS WorkSpace Unified Communication System Table of
Contents
4.3 Click to
Dial......................................................................................................................4-144.3.1
Prerequisites of Click to Dial
.................................................................................4-144.3.2
Operation Procedure of Click to
Dial.....................................................................
4-14
4.4 Enhanced Caller ID
Display.............................................................................................4-144.4.1
Prerequisites of Enhanced Caller ID
Display........................................................
4-144.4.2 Operation Procedure of Enhanced Caller ID
Display............................................4-14
4.5 Click to
Forward...............................................................................................................
4-154.5.1 Prerequisites of Click to
Forward..........................................................................4-154.5.2
Operation Procedure of Click to
Forward..............................................................
4-15
4.6 Holding and Retrieving Incoming Call
.............................................................................4-164.6.1
Prerequisites of Holding and Retrieving Incoming
Call......................................... 4-164.6.2 Operation
Procedure of Holding and Retrieving Incoming Call
............................ 4-16
4.7 Holding and Retrieving Outgoing Call
.............................................................................4-174.7.1
Prerequisites of Holding and Retrieving Outgoing
Call......................................... 4-174.7.2 Operation
Procedure of Holding and Retrieving Outgoing Call
............................ 4-17
4.8 Terminating Incoming Call
...............................................................................................
4-174.8.1 Prerequisites of Terminating Incoming Call
..........................................................
4-174.8.2 Operation Procedure of Terminating Incoming
Call.............................................. 4-17
4.9 Click to Conference
.........................................................................................................
4-184.9.1 Prerequisites of Click to
Conference.....................................................................
4-184.9.2 Operation Procedure of Click to Conference
........................................................ 4-184.9.3
Click to Conference Operations
............................................................................
4-19
4.10 Changing Status of UC
Subscriber................................................................................4-214.11
Intelligent Routing by
Presence.....................................................................................4-22
4.11.1 Entering [Intelligent Routing]
Window.................................................................
4-224.11.2 Setting Caller Group
Information.........................................................................
4-224.11.3 Setting Transferred-To Number
Group...............................................................
4-244.11.4 Setting Intelligent Routing
Policy.........................................................................4-25
4.12 Intelligent Call Routing by Time State
...........................................................................
4-274.12.1 Entering [Intelligent Routing]
Interface................................................................
4-274.12.2 Setting Caller Group
Information.........................................................................
4-274.12.3 Setting Transferred-To Number
Group...............................................................
4-284.12.4 Setting Time
State...............................................................................................
4-294.12.5 Setting Time State Intelligent Call Routing
Policy............................................... 4-30
4.13 Temporary Binding
CTD................................................................................................
4-314.14 Temporary Binding Calling Processing
.........................................................................4-314.15
Querying Call
Log..........................................................................................................
4-32
Chapter 5 Troubleshooting
..........................................................................................................
5-15.1 Classification of Fault Causes
...........................................................................................5-15.2
Troubleshooting Procedure
...............................................................................................5-1
5.2.1 Checking Network
Communication.........................................................................
5-15.2.2 Checking UC Data Configuration for
SoftX3000.....................................................
5-1
iii
-
8/8/2019 U-SYS WorkSpace UC User Manual
15/227
User ManualU-SYS WorkSpace Unified Communication System Table of
Contents
5.3 Treatment of Network Communication Faults
...................................................................
5-25.3.1 Server Working Abnormally After Restarting
.......................................................... 5-25.3.2
Failure in Logging in to
System...............................................................................
5-25.3.3 Failure in Adding Trusted
Site.................................................................................
5-35.3.4 Failure in Modifying Password in Login
Window.....................................................
5-35.3.5 Failure in Logging in to Instant Message
Server.....................................................5-3
5.4 Treatment of Typical Operational Faults
...........................................................................5-45.4.1
User Unable to Click to Dial
....................................................................................
5-45.4.2 Failure in Starting UCA Service
..............................................................................5-45.4.3
Failure in Starting Call Log
Service.........................................................................
5-4
5.5 Solution to Typical Operational Problems on UC
Client....................................................
5-5Appendix A Configuring UC Service Data in SoftX3000
...........................................................A-1
A.1 Overview of
Configuration.................................................................................................A-1
A.1.1 Objective of Configuration
......................................................................................A-1A.1.2
Prerequisites of Configuration
................................................................................A-1A.1.3
Description of Configuration Relationship
..............................................................A-1A.1.4
Preparations for UC-Related
Data..........................................................................A-1A.1.5
Configuration
Procedure.........................................................................................A-1A.1.6
Relations Between Database Tables
.....................................................................A-2
A.2 Adding Workstation
...........................................................................................................A-3A.2.1
MML
Commands.....................................................................................................A-3A.2.2
Description of Configuration
...................................................................................A-4A.2.3
Description of Parameters
......................................................................................A-4
A.3 Adding UC
Group..............................................................................................................A-4A.3.1
MML
Commands.....................................................................................................A-4A.3.2
Description of Parameters
......................................................................................A-4
A.4 Adding UC
User.................................................................................................................A-5A.4.1
MML
Commands.....................................................................................................A-5A.4.2
Description of Parameters
......................................................................................A-5
A.5 Configuration Instance
......................................................................................................A-7A.5.1
Instance
Data..........................................................................................................A-7A.5.2
Steps of Configuration
............................................................................................A-7
A.6 Optional
Configurations.....................................................................................................A-8
A.6.1 Adding UC Caller
Group.........................................................................................A-8A.6.2
Adding UC Intelligent Call Routing
.........................................................................A-9A.6.3
Adding UC Week
Information...............................................................................A-11A.6.4
Adding UC Date
Information.................................................................................A-13A.6.5
Adding UC Time State
Information.......................................................................A-14
Appendix B Typical Service
Flows..............................................................................................B-1B.1
CTD Service
Flow..............................................................................................................B-1B.2
CTF Service
Flow..............................................................................................................B-2B.3
Enhanced Caller ID Service
Flow......................................................................................B-3
iv
-
8/8/2019 U-SYS WorkSpace UC User Manual
16/227
User ManualU-SYS WorkSpace Unified Communication System Table of
Contents
B.4 CTC Service
Flow..............................................................................................................B-3B.5
Temporary Binding (Remote Office) Service
Flow............................................................B-4B.6
Flow of CTD Service of Temporary Binding
Service.........................................................B-5B.7
Flow of Call Processing Service of Temporary Binding Service
.......................................B-7B.8 ICR Service
Flow...............................................................................................................B-7
B.8.1 ICR Service Setting
Flow........................................................................................B-7B.8.2
ICR Service Processing
Flow.................................................................................B-8
B.9 Unified Message Service
Flow..........................................................................................B-9B.9.1
Flow of Instant Message Notification of Unanswered Call
.....................................B-9B.9.2 Flow of Transferring
Voice Mailbox to Email
........................................................B-10
Appendix C Acronyms and Abbreviations
.................................................................................C-1Index
................................................................................................................................................
i-1
v
-
8/8/2019 U-SYS WorkSpace UC User Manual
17/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-1
Chapter 1 System Description
1.1 Introduction to Unified Communication System
The U-SYS Workspace Unified Communication System (hereinafter
referred to as the
UC system) is developed based on Huawei U-SYS next generation
network (NGN)
solution.
It fully incorporates the functions of enterprise-oriented
office software of Microsoft
and IBM.
It provides corporate subscribers with an integrated
communication means.
The UC system forms a platform for all communication devices
(including NGN devicesin the external communication network and
internal Internet devices) to integrate and
interwork with each other. Through this platform, corporate
subscribers can use various
kinds of devices, including telephones, mobile phones and PCs to
access and control
voice messages, faxes, short messages and Emails. In this way,
subscribers can
communicate in a flexible, real-time manner.
With the diversification of communication means, subscribers can
enjoy
communication services by using different devices. Refer to
Table 1-1.
Table 1-1 Corresponding relation between services and devices
supporting them
Service Device
Voice Telephone terminalVoice mailbox Telephone terminalEmail
Personal computer (PC) or personal digital assistant (PDA)Fax Fax
machineShort message service (SMS) Mobile telephone terminalInstant
message PC or PDA with client softwareVideo Video terminalTelephone
conference Conference terminal
As shown in the table, there is a variety of communication modes
that can be used by
subscribers with corresponding devices offered. Therefore, it
has become a pressing
challenge on how to associate these devices effectively to
better serve subscribers.
Especially for the enterprises using Internet as the office
network, the integration
between Internet devices and external communication network
equipment has become
their urgent demand.
-
8/8/2019 U-SYS WorkSpace UC User Manual
18/227
-
8/8/2019 U-SYS WorkSpace UC User Manual
19/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-3
1.2.3 Click to Fax
Click To Fax (CTF) based on VoIP means that a UC subscriber can
send a fax message
to the callee through the VolP network by clicking the
corresponding link on the Web
page. The SoftX3000 uses the extension part of the Intelligent
Network Application
Protocol (INAP) and the T.38 protocol to transmit fax
information.
1.2.4 Instant Message
Instant Message (IM) is the information in text format exchanged
among multiple UC
subscribers in real time, which needs not be saved. However, IM
is different from
common Email, for it is the text message sent in real time. It
can send presence
information to other participants in real time.
IM is compatible with mobile messages, Internet messages and
fixed messages, sothat mobile subscribers, Internet subscribers,
and fixed subscribers can chat through
multimedia devices.
1.2.5 Presence
Presence means the states of a UC subscriber in the office
network, including Offline,
Online, Away, and one to thirteen extended states. The first
three states are basic
states. You can customize an extended state to meaningful
character strings, for
example, Working, Meeting, or Having meal.
With this service, a UC subscriber can publicize or modify
his/her current state or evenmood over the network. In addition,
this service supports the subscription by other UC
subscribers to view the current state of a presence subscriber;
that is, when the state of
the presence subscriber changes, this service will notify
relative UC subscribers of the
state change.
The presence service supports the following functions:
A UC subscriber can modify or publicize his/her state.
A UC subscriber can set to change his/her state automatically
based on time. For
example, set that the state is displayed as Online between 8:00
and 12:00, and
then changed to Offline between 12:00 and 12:30. The change of
state will affect the intelligent routing immediately, so that the
UC
system can change the communication route in real time.
The presence is coupled with the address list and IM.A UC
subscriber can see the
state of other UC subscribers in the [Address list] page, and
can see and modify
his/her own state in the [Instant message] page.
Before obtaining the state of other UC subscribers, a UC
subscriber needs to
acquire the permission from those subscribers.
The presence service can be used in cooperation with other
services, providing
subscriber state information for these services. Take the
combination of the
presence service and the multimedia conference service as an
example. When a
-
8/8/2019 U-SYS WorkSpace UC User Manual
20/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-4
UC subscriber is at a conference, the multimedia conference
service supports the
display of the state of all the participants based on the
information provided by the
presence service.
1.2.6 Phone Presence
I. Overview of Phone Presence
Phone presence refers to the state of the phone set of a UC
subscriber in the office
network, including the busy state and idle state. A UC
subscriber can see the phone
state of other UC subscribers in the [Address list] page.
If UC subscriber A subscribes the phone state of UC subscriber B
through the phone
presence service, when subscriber Bs phone set changes from busy
to idle state (due
to on-hook, for example), this service will notify subscriber A
of the state change of
subscriber B through Email, Short Message Service (SMS) or IM.
At this time,
subscriber A can select the most appropriate means to
communicate with subscriber B.
1.2.7 Intelligent Call Route
I. Overview of Intelligent Call Route
To better meet individual requirements and improve the Quality
of Service (QoS), the
U-SYS UC system provides the Intelligent Call Route (ICR)
service.
Flexible routing policy can be set by a UC subscriber on the Web
page or by the carrier
administrator through MML commands based on any combination of
caller level, calling
number, subscriber state, phone state, weekday and time. In this
case, different levels
of callers are served differently, thus enhancing communication
quality and effect.
II. Classification of ICR modes
As shown listed Table 1-3, ICR modes include the following
modes:
No operation
Rejecting call
Forwarding to voice mailbox
Sending description information to text terminal Serial
forwarding
Parallel forwarding.
Table 1-3 ICR modes and descriptions
ICR mode Description
None Normal call
Reject Incoming calls are rejected directly.VMS An incoming call
is forwarded to the voice mailbox of a UC subscriber.
-
8/8/2019 U-SYS WorkSpace UC User Manual
21/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-5
ICR mode Description
Text NoneSequent forward
An incoming call is forwarded to several subscribers one by one
based
on the pre-defined sequence until it is put through. The
duration of callattempt to each forwarded-to subscriber can be set
differently.
Parallel forward An incoming call is forwarded to the
pre-defined subscriberssimultaneously until it is answered.
There are also other supplementary modes:
Forwarding to SMS
A short message is sent to notify a UC subscriber of a missed
call.
Combined forwarding
After an incoming call fails to be forwarded to several
subscribers simultaneously or
based on the preset sequence, it is then forwarded to the voice
mailbox or SMS.
III. Selection of ICR Mode
Select ICR mode based on caller
The device chooses different ICR modes according to different
caller groups. Different
callers can be grouped by leaders, colleagues or friends. A
maximum of 10 caller
groups can be defined and a maximum of 20 subscribers can be
allocated to different
groups by prefix. For example, the numbers prefixed with 0 can
be grouped in the tollcall user group.
Select ICR mode based on presence
Different ICRs can be adopted according to the current state of
a UC subscriber (online,
offline or away).
Select ICR mode based on time
Different ICRs can be adopted according to the time when an
incoming call is received.
Note:The above ICR selection methods can be used together.
1.2.8 Remote Office
With the remote office service, the UC functions of UC
subscriber A can be bound to
NGN subscriber B temporarily through the modification of the
relative information on
the Web page by the UC subscriber or through MML commands
carried out by the
-
8/8/2019 U-SYS WorkSpace UC User Manual
22/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-6
carrier administrator, so that NGN subscriber B can enjoy the UC
functions of UC
subscriber A.
This service ensures that a UC subscriber can continue enjoying
the UC services even
if he/she is away from the original office (for example, on
business).
1.2.9 Unified Message
Unified Message (UM) service indicates the media conversion
capability of the UC
system. No matter where a UC subscriber is, he/she can receive
Emails, voice mails,
calls, video calls, short messages, and faxes.
Converting non-answered calls to instant messages for
notification.
Converting missed calls to short messages for notification.
Converting voice mails to Emails.
Converting faxes to Emails.
Converting Emails to faxes, that is, CTF.
1.3 Functions
1.3.1 Portal
When the UC system is applied in enterprises, it offers a Web
entry for accessing the IT
system and communication capability of an enterprise. By setting
up a dedicated page
in the enterprise portal for integrating various
communication-related functions, the
staff can select contact means flexibly and conveniently during
work time. The portal
interface (including combination of functions) can be customized
based on the specific
requirements of each enterprise.
1.3.2 Single Sign On
The UC system provides the Single Sign On (SSO) function; that
is, after a subscriber
logs in to the UC system with only one password entered, he/she
can use the services
directly.
1.3.3 Personal Information Management t
Personal Information Management (PIM) includes the management of
Emails,
calendars, schedules and tasks.
1.3.4 Address List
In the address list, such information as user name, employee ID,
department, various
kinds of telephone numbers, and Email address are displayed.
Apart from the above information, the UC system also adds such
functions as showing
user state and phone state, CTD, and CTF.
-
8/8/2019 U-SYS WorkSpace UC User Manual
23/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-7
1.3.5 Call Log
The UC system offers the following call information for UC
subscribers:
Outgoing calls Answered calls
Missed calls
Forwarded calls
1.3.6 UC Administration
The subscriber authorities for the following services can be
controlled in the SoftX3000:
Click to call
CTC
Call Log Intelligent routing
IM
1.3.7 Multi-Level Service Management
The UC system supports the management of UC services at two
levels:
System level: A carrier manages the whole UC system and various
organization
units (OUs).
OU level: An enterprise manages the subscribers in OUs.
1.3.8 Network Address Translation
UC Web clients can be deployed in different networks, adopting
such standard
protocols as Hyper Text Transport Protocol (HTTP) and SIP to
achieve Network
Address Translation (NAT) traversal. Therefore, the carrier can
provide UC services to
enterprises in different networks.
1.3.9 Language Support
The UC system supports the display of the interfaces in either
Chinese or Englishbased on the language version of the browser.
1.4 Networking Principles
1.4.1 Networking Model
NGN is a service-driven network. It separates service from call
control as well as call
control from bearer to achieve a service system independent from
the network. The UC
system serves as the application server and provides abundant UC
services by
-
8/8/2019 U-SYS WorkSpace UC User Manual
24/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-8
cooperating with the SoftSwitch (SoftX3000) in the control layer
of NGN. See
Figure 1-1 for the typical networking model of UC server in
NGN.
AMG: Access Media Gateway IAD: Integrated Access DeviceTMG:
Trunk Media Gateway UMG: Universal Media GatewayIM Server: Instant
Message Server VM Server: Voice Mail Server
Figure 1-1 Networking model of UC system in NGN
1.4.2 UC Server Group
I. Overview of UC Server Group
The UC server group is a whole body composed of all the
functional modules of the UC
system. It resides in the service management layer of NGN
logically, providing
communication capabilities for IT systems. Depending on
different software functions,
the UC server group is composed of eight software modules
generally, with the core
module as UC Agent.
II. UC Agent
It is the connecting point between communication network and
Internet. Its functions
are triggering UC services and transferring MML commands between
UC subscribers
and SoftX3000.
-
8/8/2019 U-SYS WorkSpace UC User Manual
25/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-9
III. Call Log Server
Its functions are receiving call logs of UC subscribers from
SoftX3000 and saving them
in the local SQL database or the SQL database in the
network.
IV. UC Portal
It provides unified interfaces for UC subscribers, such as login
interface, operation
interface, and maintenance interface.
V. Directory Server
It adopts Microsoft Active Directory (AD) and accomplishes
authentication and
management of UC subscribers login to the UC system.
VI. IM Server
It adopts Microsoft Live Communication Server 2003 and provides
such functions as IM
and online alert within an enterprise.
VII. Email Server
It adopts Microsoft Exchange 2003 and offers secure and private
access to mobile
Emails, remote Emails and desktop Emails on client
(Outlook).
VIII. Fax Gateway
It functions are sending and receiving faxes, and converting
faxes to Emails as well as
Emails to faxes. Besides connecting with the Internet through
Transport Control
Protocol (TCP)/Internet Protocol (IP), it must provide primary
rate adaptation (PRA)
trunk to interconnect with TMG/UMG.
IX. VM Server
It is voice mailbox (VM) server. It is responsible for recording
and saving voice
messages; that is, it records the voice messages of subscribers
into digital voice files
and stores these files in the hard disk of the server, and then
the UC Agent sends them
to the Email box of the destination UC subscribers. Besides
connecting with the
Internet through TCP/IP, VM Server must provide PRA trunk to
interconnect withTMG/UMG.
Caution:
The preceding modules are logical components, and some of them
can be deployed in one server in actual
application. Both Call Log Server and UC Agent interwork with
SoftX3000 through SIP, but only one port
number can be set at SoftX3000 side, so Call Log Server and UC
Agent cannot be located in one server.
-
8/8/2019 U-SYS WorkSpace UC User Manual
26/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-10
X. Protocols for Interworking Among UC Server Group
Refer to Figure 1-2 for the protocols used for interworking
between various UC servers.
Figure 1-2 Interworking protocols between UC servers
UC Agent communicates with the SoftX3000 through standard
protocol control
interface (SIP+MML).
IM Server, Portal Server and Email Server communicate with UC
clients through
standard subscriber interfaces such as SIP and HTTP.
Directory Server communicates with FAX GW, VM Server and Email
Server
through such standard authentication interfaces as Lightweight
Directory Access
Protocol (LDAP) and Domain Name Services (DNS).
XI. Interworking between UC Server Group and Other NGN
Components
The UC server group can interwork with other NGN components in
the following
modes:
UC Agent interworks with SoftX3000 through SIP and MML.
Call Log Server interworks with SoftX3000 through SIP.
Fax Gateway interworks with TMG/UMG through PRA trunk.
VM Server interworks with TMG/UMG through PRA trunk.
1.4.3 Networking Modes
Depending on different service providers, there are two
networking modes used in
actual application.
-
8/8/2019 U-SYS WorkSpace UC User Manual
27/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-11
I. UC Services Provided by Carrier Independently
1) Networking description
In this networking mode, the carrier provides all NGN equipment
(including UC server
group). Enterprises or subscribers can enjoy UC services if only
they have PCs and
phone sets. See Figure 1-3 for this networking model.
MRS: Media Resource Server MCU: Multipoint Control UnitOpenEye:
SIP/H.323 Softphone iManger N2000: Huawei Network Management
System
Figure 1-3 Networking model of UC services provided by carrier
independently
There are three networks around SoftX3000:
Internal network of SoftX3000: BAM, iGWB and SoftX3000 are
interconnected
through LAN Switch A.
Service network: SoftX3000 (IP Forward Module (IFMI) board), UC
server group,
MRS and MCU are interconnected through LAN Switch B.
Network management network: BAM, iManager N2000 and server group
are
interconnected through LAN Switch C.
-
8/8/2019 U-SYS WorkSpace UC User Manual
28/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-12
Note:Figure 1-3 shows the networking configuration for
connecting 10,000 subscribers. Four servers are
located in the network management network, so four IP addresses
need be set fixedly in the network
management network. In addition, three external IP addresses
need be set for Server 1, Server 2 and
Server 3.
2) Networking feature
In this mode, the carrier can provide UC services to enterprises
or subscribers
independently without the need to rebuild the network, thus
facilitating the expansion of
services and the raise of profit. This mode is recommended for
the networking for
medium- and small-sized enterprises.
II. UC Services Provided by Carrier and Enterprise
Cooperatively
1) Networking description
In this networking mode, the carrier provides NGN equipment, and
the enterprises
provide PCs, phone sets and enterprise IT systems. See Figure
1-4 for this networking
model.
Figure 1-4 Networking model of UC services provided by carrier
and enterprise cooperatively
-
8/8/2019 U-SYS WorkSpace UC User Manual
29/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-13
The enterprises have only been configured with Email Server and
Directory Server, so
it is necessary to add a UC server group. Take the UC system
connecting 20,000
subscribers as an example. Refer to Table 1-4 for the
configuration of UC server group
in this networking mode.
Table 1-4 Configuration of UC server group in this networking
mode
Server No. Software modules Function
Server 1 UC Agent + IM Server Providing UC call management
interface toSoftX3000, IM and presence services.
Server 2 UC Portal + Call Log Server Providing Portal entry, Web
page and call logservices.
Server 3 Fax Gateway + VM Server Providing fax GW and voice
mailbox services.
Note:These three servers are positioned in the network
management network, so three IP addresses need be
set fixedly in the network management network. In addition,
three interfaces are offered to the external IP
network, so three IP addresses need be set fixedly also.
2) Networking feature
In this networking mode, UC Agent module is added and other
service functions areexpanded in the enterprise IT system. In this
way, the U-SYS NGN communication
capability can be used by the IT system of the enterprise and
the continuity of the IT
system can be kept. In addition, the security of enterprise
information (such as
employee position and telephone number) can be guaranteed, thus
solving the
problems related to NAT and Firewall. This mode is applicable to
the networking for
enterprises with internal IT systems (especially large- and
medium-sized enterprises).
1.5 Billing System
1.5.1 Overview of Billing System
The billing system for UC subscribers is the same as that for
common NGN subscribers
in structure. Refer to Chapter 6, Tickets, Bills and Charging
System of U-SYS
SoftX3000 Technical Manual-Architecture & Principlefor
details.
UC services apply the monthly fee mode, and each call is charged
separately.
1.5.2 Examples of Charging Cases
Suppose subscriber A has registered the CTC service, for which
the monthly charge is
N dollars. If subscriber A held only one conference within a
month, and the participants
-
8/8/2019 U-SYS WorkSpace UC User Manual
30/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-14
were subscribers B and C, subscriber A should pay: monthly
charge (N dollars) + call
charge from subscriber A to subscriber B + call charge from
subscriber A to subscriber
C.
Suppose a subscriber has registered the ICR service, for which
the monthly charge is Ndollars. If the subscriber answers calls by
using his/her own telephone E, he/she will
only pay the call answer charge (which is unnecessary if callees
are not charged). If the
subscriber answers calls on telephone F through ICR, he/she will
pay the call
forwarding fee. Therefore, the subscriber should pay: monthly
charge (N dollars) + call
answer charge on telephone E (which is unnecessary if callees
are not charged) + call
forwarding fee from telephone E to telephone F.
1.6 Technical Specifications
1.6.1 System Capacity
Refer to Table 1-5 for system capacity.
Table 1-5 System capacity
Item Specifications Remarks
Maximum number of UCsubscribers 600,000 One UC call occupies
twocommon NGN call resourcesMaximum number of enterprises 65,535
Number of IP CentrexesMaximum number of UC servers 100 None
Maximum number ofsubscribers talking with a UCsubscriber
simultaneously 15 NonePop-up time of call controlwindow
-
8/8/2019 U-SYS WorkSpace UC User Manual
31/227
User ManualU-SYS WorkSpace Unified Communication System Chapter
1 System Description
1-15
Item Specifications Remarks
Quantity of forwarded-tonumbers in case of parallelforwarding: 5
For each UC subscriber
Intelligent routingQuantity of forwarded-tonumbers in case of
serialforwarding: 5 For each UC subscriber
1.6.2 Power Consumption
I. Power Supply
Rated voltage: 48 VDC
Voltage fluctuation range:57 V to 40 V
II. Power Consumption of UC System
If the UC system carries 20,000 subscribers, the power
consumption of each server is
as shown in the following table.
Table 1-6 Power consumption of UC servers when connecting 20,000
subscribers
Function unit Power consumption (W) Configuration
Server 1 (UC Portal + Call Log Server + Mail Server) 250 Using
HP server
Server 2 (UC Agent + Directory server + IM Server) 250 Using HP
server
Server 3 (FAX gateway + VM Server) 250 Using HP server
-
8/8/2019 U-SYS WorkSpace UC User Manual
32/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-1
Chapter 2 Installation and Configuration of UC
Server2.1 Installing UC System Software2.1.1 Configuring System
and Connection Data
I. Configuration DescriptionFunctions and service modules of the
UC system can be installed and configured on
different UC servers, provided that the following conditions are
satisfied: In the UC agent, Live Communication Server (LCS), UC RTC
(Real Time
Communication) Service and UC Service must be installed and run
on the same
server.
In the Call Log, Call Log Service and SQL Server must be
installed and run on the
same server.
In the Portal, Internet Information Services (IIS), Huawei
Workspace and some
COM+ and .NET components must be installed and run on the same
server.
All relative UC functional modules must be installed on the
servers in the same
domain.
For other UC functional modules, the configuration is as
follows:
There can be multiple Exchange mail servers.
DNS and CA can be installed and configured as needed.
Note:The SoftX3000 sends SIP messages to the UC agent and Call
Log simultaneously. Therefore, to achieve
good performance, you must install the UC agent and Call Log on
the same server.
II. Typical ConfigurationTable 2-1 gives the description of the
software of UC servers for a typical configuration.
-
8/8/2019 U-SYS WorkSpace UC User Manual
33/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-2
Table 2-1Description of the software of UC servers
Server Service module Note:
UC Server1Active DirectoryDNSUC ServiceUC RTC ServiceLCS
Ethernet card 1: 189.1.1.20, used forcommunicating with the
SoftX3000 andBAM;Ethernet card 2: standby.
UC Server2UC Portal ServerCall Log ServerE-mail ServerIIS
Ethernet card 1: 189.1.1.40, used forcommunicating with the
SoftX3000;Ethernet card 2: standby.
UC Server3 Fax ServerVoicemail Server
Note:The server installed with the UC agent is called domain
controller (DC) or active directory (AD) . The server
installed with the UC Portal and Exchange is known as Portal or
Exchange. In this manual, we refer to
them as AD and Portal only.
Call Log and UC Service cannot be installed on the same
server.
For the installation and configuration of the Fax Server and
Voicemail Server, refer to the manual related.
This manual just introduces the installation and configuration
of UC Server1 and UC Server2.
III. Hardware Deployment and ConnectionFigure 2-1 illustrates
and deployment and connection of UC servers.
AD Server Portal Server
SoftX3000 BAM
IP Network
191.1.1.1/16
189.1.1.20/16 189.1.1.40/16
191.1.1.10/16
GW:191.1.1.5
GW:189.1.1.30
Figure 2-1Service deployment
-
8/8/2019 U-SYS WorkSpace UC User Manual
34/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-3
2.1.2 Overview of Software InstallationI. Installation
Procedures
Install Windows Server 2003
on AD and Portal Server
Install Active Directory on AD
Install LCS on AD Server
Install UC Software
at AD Server
Install Exchange
on Portal Server
Install UC Software
at Portal Server
Install SQL Server
on Portal Server
Add Portal Server to Domain
Install Preparation
Install Complete
Figure 2-2The UC server installation sequence
II. Hardware RequirementsThe AD and Portal servers both are PC
servers. For them, the configuration
requirements are:
Two CPUs with over 2.4 GB dominant frequency
Larger than 4 GB (double data rate) DDR memory
Two 36 GB SCSI (Disks) hard disks
CD-ROM drive
At least two 100/1000 Mbit/s Ethernet cards.
-
8/8/2019 U-SYS WorkSpace UC User Manual
35/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-4
Note:The hardware configuration of the server may be updated. So
the real configuration may be different from
what is described here.
III. Software RequirementsGet the following software ready:
Microsoft Windows Server 2003 Standard Edition
Microsoft SQL Server 2000 Standard Edition
Microsoft SQL Server 2000 Service Pack 3
Microsoft Exchange Server 2003
Microsoft Live Communication Server 2003
UC application package
Note:Microsoft Windows Server 2003, SQL Server 2000, Exchange
Server 2003 and Live Communication
Server 2003 are all products of Microsoft Corporation. For
details on usage, refer to related technical
documents of Microsoft.
Company names and trademarks mentioned in this chapter all
belong to Microsoft Corporation.
2.1.3 Installing Operating SystemI. Description of
Installation
It is recommended to install Windows Server 2003 Standard
edition on the AD and
Portal servers.
Note:For Windows 2003, the standard edition and above are
required.
II. Initializing InstallationProceed as follows:
1) Boot from CD-ROMEnter the CD into the CD-ROM, change the
system boot sequence to CD-ROM in the
Basic Enter Output System (BIOS) setting, and then save the
configuration and exit.
-
8/8/2019 U-SYS WorkSpace UC User Manual
36/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-5
Note:For some computer models, you have to press the space bar
when the system prompts you to "press any
key to boot from CD-ROM".
2) Detect and load device files
After booting from the CD-ROM, the system enters the
installation detection interface
and detects and loads devices.
3) Confirm the installation
When the loading is finished, the [Welcome] dialog box appears.
Then press to
enter the license agreement interface. Press to accept the
agreement, and then
go on.
Note:When pressing , the system prompts that Windows 2003 has
existed. Press to start a new
initial installation.
4) Create partitionsThe setup will show the partition
information of the hard disk.
If there are no partitions, press to create partitions.
If there are already partitions, which require adjustment, press
to delete these
partitions and then create new ones.
Note:It is recommended to allocate at least 10 GB for each
partition.
5) Format partitionsAfter having created partitions, use the /
arrow keys to select a partition,
and then press .
If you select to install the OS in a newly created partition,
the setup will format that
partition.
If there is some other Windows OS in the partition, press to
confirm
formatting.
-
8/8/2019 U-SYS WorkSpace UC User Manual
37/227
-
8/8/2019 U-SYS WorkSpace UC User Manual
38/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-7
Note:To select Per Server or Per Device/Per User is up to the
charging by Microsoft. Usually, if there are
multiple servers of different types, with clients relatively
fixed, select Per Device. If you are at a loss to
make a judgment at the installation, adopt the default settings.
After the installation of the OS, you can
modify the licensing mode in [Control Panel/Licensing].
4) Set computer name and administrator password2003:
In the [Computer Name and Administrator Password] dialog box,
enter the computer
name and administrator password.
Note:For the AD servers, you can enter UCRTC for computer name,
for the Portal servers, you can enter
UCPORTAL.
You have to enter the administrator password twice for
confirmation. The password must conform to the
password setting rules. For example, Example@1. If not, the
setup will give a prompt. This will affect your
accessing the UC web interfaces.
5) Set date and time
In the [Date and Time Setting] dialog box, set the correct date,
time and time zone, and
then click .
Caution:
Select the correct time zone. Otherwise, you will not be able to
log in to the UC server.
After the installation of the OS, you can also modify the time
zone in [Control Panel/Date and Time].
6) Fulfill networking settingIn the [Networking Settings] dialog
box, select typical settings, and click . Keep
the default setting in the [Workgroup or Computer Domain] dialog
box (WORKGROUP),
and click .
7) Copy files and install Windows
-
8/8/2019 U-SYS WorkSpace UC User Manual
39/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-8
Start copying Windows system files, install Windows and make
settings. After the full
installation and setting, the computer will automatically
restart (at this time you can take
out the Windows Server 2003 CD-ROM.
8) Check after installing Windows
When the logon interface appears at the restart, press , enter
the
administrator password and enter the left side of Windows. If
the interface as shown in
Figure 2-3 appears, it indicates the installation is
successful.
Figure 2-3The interface at the restart after the successful
installation of Windows
Note:
To prevent the interface as shown in Figure 2-3 from appearing
when the computer restarts later, checkDont display this page at
logon.
9) Perform subsequent operations after installing WindowsThe
following operations are required after installing Windows:
Partition and format: If you have not performed logic
partitioning or formatting to
the Extended Partition during the installation, do so with
reference to the Windows
computer administrative tools.
-
8/8/2019 U-SYS WorkSpace UC User Manual
40/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-9
Install the patch: Configure the network to access the Internet,
and then log on to
Microsofts web site with [Start/Windows Update] to install the
security patch.
2.1.4 Installation of Active DirectoryI. Prerequisites for
Installation
Ensure that the following are ready installed before installing
Active Directory:
Windows Server 2003.
The IP addresses, subnet masks, and default gateways of the
Ethernet cards in
the AD and Portal servers.
The UC server has been correctly connected to the network.
You have logged on to the AD server as the administrator.
II. Installing Active Directory on AD ServerProceed as
follows:
1) Run the setup
Select [Start/Run], enter dcpromo and click to enter the Active
Directory
Installation Wizard interface as shown in Figure 2-4. Click to
go on the
installation.
Figure 2-4The Active Directory installation welcome window
2) Select a domain controller type
-
8/8/2019 U-SYS WorkSpace UC User Manual
41/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-10
The next window of the Active Directory Installation Wizard
shows the OS compatibility
information, as shown in Figure 2-5.
Figure 2-5The OS compatibility information of the Active
Directory Installation Wizard
Click . The domain controller type selection window appears, as
shown in
Figure 2-6.
-
8/8/2019 U-SYS WorkSpace UC User Manual
42/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-11
Figure 2-6The domain controller type selection window
Keep the default setting, that is, Domain controller for a new
domain (as shown in
Figure 2-6, and click .
3) Create a domain forestThe [Create New Domain] window shows
next, as shown in Figure 2-7.
-
8/8/2019 U-SYS WorkSpace UC User Manual
43/227
-
8/8/2019 U-SYS WorkSpace UC User Manual
44/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-13
Figure 2-8The window for setting the DNS name of a domain
In Figure 2-8, enter the full DNS name for a new domain (since
this domain name will
be used across the Internet, it must be obtained from the
telecom administrator with itsapproval), and then click to enter
the [NetBIOS Domain Name] window, as
shown in Figure 2-9.
-
8/8/2019 U-SYS WorkSpace UC User Manual
45/227
-
8/8/2019 U-SYS WorkSpace UC User Manual
46/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-15
Figure 2-10Database and log folders
Keep the default path as shown in Figure 2-10, and click to
enter the [Shared
System Volume] window, as shown in Figure 2-11.
-
8/8/2019 U-SYS WorkSpace UC User Manual
47/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-16
Figure 2-11The window for specifying the folder to be shared as
the system volume
Keep the default path set as shown in Figure 2-11, and then
click .
6) Install DNSThe [DNS Registration Diagnostics] window appears
next, as shown in Figure 2-12.
-
8/8/2019 U-SYS WorkSpace UC User Manual
48/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-17
Figure 2-12The DNS registration selection window
In Figure 2-12, select Install and configure the DNS server on
this computer, and set
this computer to use this DNS server as its preferred DNS
server, and then click.
Note:If you have installed and configured the DNS server on the
AD server, or you have specified an existing
DNS server for the network connection, the above step will not
appear during the installation.
7) Set permission compatibility options
The [Permissions] window appears next, as shown in Figure
2-13.
-
8/8/2019 U-SYS WorkSpace UC User Manual
49/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-18
Figure 2-13Permission setting
In Figure 2-13, select Permissions compatible only with Windows
2000 or Windows
Server 2003 operating systems, and then click .
Note:Selecting Permissions compatible only with Windows 2000 or
Windows Server 2003 operating systems
will ensure a secure communication and reduce data flow of the
network.
8) Set the restore mode administrator password
The [Directory Services Restore Mode Administrator Password]
window appears next,
as shown in Figure 2-14.
-
8/8/2019 U-SYS WorkSpace UC User Manual
50/227
User ManualU-SYS Workspace Unified Communication System Chapter
2 Installation and Configuration of UC Server
2-19
Figure 2-14Setting the restore mode administrator password
In Figure 2-14, enter the password twice (normally, keep the
restore mode password
consistent with the domain administrator password), and then
click .
III. Configuring Active Directory After Installation
1