This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
1
LC-10A2H-S/ALC-10A2M-S/A
SERVICE MANUAL !
In the interests of user-safety (Required by safety regulations in some countries) the set should be restoredto its original condition and only parts identical to those specified should be used.
MODELS
LC-10A2H-S/ALC-10A2M-S/A
LCD COLOUR TELEVISION !"#$
!"#$%= E !"#$%&'($)*F= !"#$%&'()*+,-./0123456 !"#$
» IMPORTANT SERVICE SAFETY PRECAUTION ...... 2» SPECIFICATIONS ............................................. 3» OPERATION MANUAL ...................................... 4» REMOVING OF MAJOR PARTS ....................... 6» ADJUSTING PROCEDURE OF
EACH SECTION ................................................ 9» TROUBLE SHOOTING TABLE ........................ 12» CHASSIS LAYOUT .......................................... 28» BLOCK DIAGRAM ........................................... 30» DESCRIPTION OF SCHEMATIC DIAGRAM .. 31» SCHEMATIC DIAGRAM .................................. 32» PRINTED WIRING BOARD ASSEMBLIES ..... 40» PARTS LISTË ELECTRICAL PARTS .................................. 44
MAIN UNIT .................................................. 44TERMINAL UNIT ......................................... 49OPERATION UNIT ....................................... 50LED UNIT .................................................... 50RELAY UNIT ................................................ 50
Ë CABINET AND MECHANICAL PARTS ....... 50Ë ACCESSORIES PARTS .............................. 52Ë PACKING PARTS ......................................... 52
» PACKING OF THE SET ................................... 53
SHARP CORPORATION
2
LC-10A2H-S/ALC-10A2M-S/A
CAUTION: FOR CONTINUED PROTECTIONAGAINST A RISK OF FIRE REPLACE ONLY WITHSAME TYPE FUSE. F3701 (1.25A, 250V), F3702(1.25A, 250V), F3751 (2.0A, 250V) FUSE.
Many electrical and mechanical parts in LCD televisionhave special safety-related characteristics.These characteristics are often not evident from visualinspection, nor can protection afforded by them benecessarily increased by using replacement componentsrated for higher voltage, wattage and etc.Replacement parts which have these special safetycharacteristics are identified in this manual; electricalcomponents having such features are identified by “ å”
IMPORTANT SERVICE SAFETY PRECAUTIONË Service work should be perfomed only by qualified service technicians who are thoroughly
familiar with all safety checks and the servicing guidelines which follow:
and shaded areas in the Replacement Parts Lists andSchematic Diagrams.For continued protection, replacement parts must beidentical to those used in the original circuit.The use of a substitute replacement parts which do nothave the same safety characteristics as the factoryrecommended replacement parts shown in this servicemanual, may create shock, fire or other hazards.
WARNING
1. For continued safety, no modification of any circuitshould be attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER(Fire & Shock Hazard)
Before returning the receiver to the user, performthe following safety checks:
1. Inspect all lead dress to make certain that leads arenot pinched, and check that hardware is not lodgedbetween the chassis and other metal parts in thereceiver.
2. Inspect all protective devices such as non-metalliccontrol knobs, insulation materials, cabinet backs,adjustment and compartment covers or shields,isolation resistor-capacitor networks, mechanicalinsulators and etc.
3. To be sure that no shock hazard exists, check forleakage current in the following manner.
• Plug the AC cord directly into a 110~240 volt AC outlet,and connect the DC power cable into the receiver'sDC jack. (Do not use an isolation transformer for thistest).
• Using two clip leads, connect a 1.5k ohm, 10 wattresistor paralleled by a 0.15µF capacitor in series withall exposed metal cabinet parts and a known earthground, such as electrical conduit or electrical groundconnected to an earth ground.
• Use an AC voltmeter having with 5000 ohm per volt, orhigher, sensitivity or measure the AC voltage dropacross the resisor.
• Connect the resistor connection to all exposed metalparts having a return to the chassis (antenna, metalcabinet, screw heads, knobs and control shafts,escutcheon and etc.) and measure the AC voltage dropacross the resistor.All checks must be repeated with the AC cord plugconnection reversed. (If necessary, a nonpolarizedadaptor plug must be used only for the purpose ofcompleting these checks.)Any reading of 35V peak (this corresponds to 0.7milliamp. peak AC.) or more is excessive and indicatesa potential shock hazard which must be correctedbefore returning the monitor to the owner.
TO EXPOSEDMETAL PARTS
CONNECT TOKNOWN EARTHGROUND
DVMAC SCALE
50k ohms.10W
0.15 µFTEST PROBE
3
LC-10A2H-S/ALC-10A2M-S/A
SpecificationsLCD panel ............................................................................................... 10.4" TFT LCDNumber or pixels ............................................................................. 921,600 pixels VGAVideo colour systems....................................................................... PAL/NTSC/SECAMTV FUNCTION
TV Standard (CCIR) ................................................................................. I/DK/M/BGTV Turning System .....................................................................Auto preset 100 ch.STEREO/BILINGUAL ........................................................................... AV STEREOUniversal R/C for TV only ................................................................................... YESAUTO PRESET ................................................................................................... YESCATV ..................................................................................................... ~Hyper Band
Lamp life ................................................................................................... 25,000 HoursViewing angles ................................................................................................... H : 120°
V : 100°Audio amplifier .................................................................................................1.0 W × 2Speakers ................................................................................................ 3 × 4 cm, 2 pcsTerminals
AV1 .......................................................................................................AV-IN 1, S-INAV2 ................................................................................................................ AV-IN 2AV OUT ......................................................................................................... AV-OUTANT ...................................................................................................................... DINH/P ........................................................................................... 3.5 mm ø jack (Rear)
OSD Language ......................................................................... English/Chinese/ArabicPower supply.............................................................................. DC 12 V, AC110-240 VWeight ........................................................................................ 2.0 kg w/o accessoriesAccessories ...................R/C, Batteries, Wall mount parts, Antenna cable, AC adapter,
AC cord, AV cable for mini-jack
Design and specifications are subject to change without notice.
4
LC-10A2H-S/ALC-10A2M-S/A
Operation Manual
Main unit (front view)
Main unit (rear view)
Remote control
5
LC-10A2H-S/ALC-10A2M-S/A
Dimensions
(Units: mm)
Front View
Rear View
Side View
6
LC-10A2H-S/ALC-10A2M-S/A
REMOVING OF MAJOR PARTS1. Remove the five lock screws 1 off the cabinet B.2. Push on the six hooks 2 of the cabinet B and open it slightly.3. Disconnect all the connectors 3 from the terminal and operation PWBs. Detach the cabinet B.4. Disconnect all the connectors 4 from the main PWB.
11
2
2
2
2
2
2
1
11
P2001
P3203
P3204
SC401
P7013
333
P701 P751
P2001
P2002
P752 P401 SC1201
SC1203
P301
4
4
4
4
Cabinet B
Cabinet A
(Main PWB)
7
LC-10A2H-S/ALC-10A2M-S/A
5
6
6
5
7
7
8
8
9
5. Remove the four lock screws 5 off the main PWB.6. Remove the two lock screws 6 off the remote control PWB.7. Remove the two lock screws 7 off the terminal PWB.8. Remove the two lock screws 8 off the operation PWB.9. Remove the two lock screws 9 off the flexible shield, and detach he relay PWB.
Main PWB
LC display unit
Cabinet A
Cabinet B
LED PWB
Operation PWB
Terminal PWB
Flexible shield
Relay PWBLC display unit(rear view)
8
LC-10A2H-S/ALC-10A2M-S/A
10
11
11
11
11
11
12
11
11
10.Remove the lock screw 0 off the LC display unit.11.Undo the seven hooks q to release the unit frame.12.Detach the fluorescent lamp.
LC Display Unit(Front View)
Panel Holder
9
LC-10A2H-S/ALC-10A2M-S/A
ADJUSTING PROCEDURE OF EACH SECTIONThe best adjustment is made before shipping. If any position deviation is found or after part replace is performed,adjust as follows.
1. Preparations for AdjustmentsUse the specific AC adaptor or a regulated DC power supply.AC adaptor : UADP-0209CEZZ (Type 10 non-polar LC10A2H/M)DC power supply : 12 V, 3.2 A
2. Calling the adjustment process modeThe mode can be called up in the following two ways.» Turn on the power and press the ADJUST PROCESS key on the remote controller.» Set either the KEY4 (Pin 81 of microprocessor) or KEY5 (Pin 82 of microprocessor) to the L level and turn on the
power.
3. Key operation in adjustment process modeSelecting a reception channel» Using the CH UP/DOWN keys, search up and down a reception channel.
Clicking on the keys : Channels are selected up or down one by one.Holding down the keys : The next receivable channel is searched up or down.
» Various adjustmentsEach of the adjustments is made by selecting an item on the menu and using the CH UP/DOWN and VOL UP/DOWN keys (on the TV set and remote controller).
» Using the menu select key, the adjustment items are picked up alternately. (Picking the next item)When the bottom item is selected and the menu select key is activated, the top item on the next page will beselected instead.
» Using the picture select key, the adjustment items are picked up alternately. (Picking the previous item)When the top item is selected and the picture select key is activated, the bottom item on the previous page willbe selected instead.
» When an item is selected and the auto preset key is activated, the top item on the next page will always beselected.Page 1 → Page 2 → ... → Page 15 → Page 1 ...
» When an item is selected and the manual memory key is activated, the top item on the same page will always beselected.Using the VOL UP/DOWN keys, the setting of the selected item can be turned up or down.
» Suppose PAL/NTSC is selected for p.14 and p.15. Using the VOL UP/DOWN keys, the register select mode iscalled and the cursor goes to Address 01.
» The CH UP/DOWN keys are used to move up and down the cursor and the VOL UP/DOWN keys to move it rightand left. The key 12 is then used to fix an item. Once fixed, the cursor will go to the item’s current setting. Usingthe VOL UP/DOWN keys, modify the setting as required.
Save the setting with the key 12 and return to the address select screen. Using the menu select key as usual,move to the next item. The cursor moves as follows by using the VOL UP/DOWN keys on the address selectscreen.
Example : 01 ←→ 02 ←→ 03 ←→ 01 ←→ ...
The cursor moves as follows by using the CH UP/DOWN keys.Example : 02 ←→ 05 ←→ ... ←→ 06 ←→ 02 ←→ ...
10
LC-10A2H-S/ALC-10A2M-S/A
4. InitializationHere is the procedure of initializing the EEPROM and making model number and size settings.4-1. Get Pins (81) and (82) of the IC2001 (microprocessor) grounded and turn on the power.4-2. Select a model number (A1, A2H, A2U). For Models LC-10A2H and LC-10A2M, select A2H.4-3. Select a size in inches (10, 12, 15, 20). For Models LC-10A2H and LC-10A2M, select 10.4-4. Get Pins (81) and (82) of the IC2001 (microprocessor) back to normal.
5. Adjustments5-1. +B adjustment
Vary the “+B-ADJ” setting on Page 1 of the adjustment process so that the voltage at pin 49 of SC401 be 5.00±0.02 V.Note : Adjust precisely to 5.0 V because this level will be used as supply voltage reference.
5-2. Counter-bias adjustmentVary the “COM BIAS” setting on Page 2 of the adjustment process so that the contrast be sharpest (blacklooks most sinking). The adjustment guideline is around 117 for Model LC-10A2H.
5-3. White balance adjustmentVary the “RCUTOFF” and “BCUTOFF” settings to achieve optimum white balance.Note : For the “RCUTOFF” and “BCUTOFF” settings, keep the readings in the range of -10 to +10. If out of
this range, the user-adjustable range is reduced.
6. Factory settings» When using the adjustment remote controller:
The factory settings are made using the adjustment remote controller. Here are some differences between thedifferent models.
Model number Key name Remote control code Setting S-SYSTEM OSD language for settings
LC10A2H Factory setting 1 100000111111110 I CHINESE
LC10A2M Factory Setting 2 100000001010110 B/G ENGLISH
» When not using the adjustment remote controller:(Applicable only with Model LC-10A2H. For Model LC-10A2M, make the following settings, and select Englishand B/G for OSD language and S-SYSTEM, respectively.)Hold down the TV/VIDEO and MENU keys on the TV set and turn on the power. Make sure the character “K”appears at the top left on the screen. Then press the VOLUME UP and CH UP keys at the same time.
11
LC-10A2H-S/ALC-10A2M-S/A
7. OSD Menu (for pages 1 and 2)
Page Item MIN MAX Remarks
1 +B-ADJ 0 255 160 Refer to 5-1
MODEL A2H Refer to 4-2
INCH SIZE 10 Refer to 4-3
TIMER 1
MPX 2
SYSTEM AUTO
NTSC PWM FREQ 000 FFF 0C0
PAL PWM FREQ 000 FFF 0BD
IR ON
D TANSHI ON
CLOSED CAPTION OFF
V-CHIP OFF
TV GAIN OFF
ERROR NO RESET 0 WAIT
2 COMBIAS 0 255 100 Refer to 5-2
NTSC TAMP 0 63 27
PAL TAMP 0 63 27
SECAM TAMP 0 63 27
PAL-M TAMP 0 63 27
TV H-PEAKING 0 63 27
R CUT OFF 0 7 4
G CUT OFF -15 +15 0 Refer to 5-3
B CUT OFF -15 +15 0
G3 -15 +15 0 Refer to 5-3
B3 00 FF 00
R3 00 FF 00
G1 00 FF 00
B4 00 FF 00
Y 00 FF 00
InitialSetting
12
LC-10A2H-S/ALC-10A2M-S/A
TROUBLE SHOOTING TABLE
No
pic
ture
at
all
Yes
No
Are
inpu
ts
and
outp
uts
of IC
802
as
spec
ified
?
Che
ck a
ll th
e se
tting
s on
the
mic
ropr
oces
sor’s
adj
ust p
roce
ss m
enu.
No
pic
ture
Che
ck IC
802
and
its
perip
hera
l pa
rts.
Yes
No
Are
inpu
ts
and
outp
uts
of IC
1201
as
spec
ified
?
Che
ck
IC12
01 a
nd
its p
erip
hera
l pa
rts.
Che
ck L
CD
pa
nel v
olta
ge
and
wav
efor
m.
No
TV
an
d
VID
EO
1
ou
tpu
t Yes
No
Are
inpu
ts
and
outp
uts
of IC
402
as
spec
ified
?
Che
ck IC
402
and
its
perip
hera
l pa
rts.
NO
Is in
put a
t Pin
(7
3) o
f IC
802
as s
peci
fied?
Che
ck IC
802,
A
V1
line
and
thei
r pe
riphe
ral
part
s.
No
TV
o
utp
ut Yes
No
Are
vol
tage
s at
Pin
s (6
),
(7)
and
(9)
of
tune
r as
sp
ecifi
ed?
Che
ck th
e po
wer
line
.
Yes
No
Is o
utpu
t at
Pin
(19
) of
tu
ner
as
spec
ified
?
Che
ck th
e tu
ner
and
its
perip
hera
l pa
rts.
No
Is in
put a
t Pin
(1
) of
IC40
2 as
spe
cifie
d?
Che
ck th
e lin
e in
qu
estio
n.
Yes
Che
ck IC
402
and
its
perip
hera
l pa
rts.
Yes
No
Are
Pin
s (2
) an
d (4
) of
IC
402
at “
H”
and
“L”
resp
ectiv
ely?
Are
Pin
s (6
5)
and
(66)
of
IC20
01 a
t “H
” an
d “L
” re
spec
tivel
y?
No
VID
EO
1
ou
tpu
t
YE
S
No
Is in
put a
t Pin
(1
) of
IC40
2 as
spe
cifie
d?
Che
ck th
e lin
e in
qu
estio
n.
Yes
No
Are
Pin
s (1
) an
d (4
) of
IC
402
both
at
“L”?
No
VID
EO
2
ou
tpu
t
No
Is in
put a
t Pin
(7
4) o
f IC
802
as s
peci
fied?
Che
ck J
3404
, A
V li
ne a
nd
thei
r pe
riphe
ral
part
s.
No
S
VID
EO
o
utp
ut No
Are
inpu
ts a
t P
ins
(71)
and
(7
2) o
f IC
802
as s
peci
fied?
Che
ck
SC
3301
, SY
lin
e, S
C li
ne
and
perip
hera
l pa
rts.
Are
Pin
s (6
5)
and
(66)
of
IC20
01 b
oth
at “
L”?
Che
ck IC
402
and
its
perip
hera
l pa
rts.
Yes
Che
ck th
e lin
e in
qu
estio
n.
Yes
Che
ck th
e lin
e in
qu
estio
n.
13
LC-10A2H-S/ALC-10A2M-S/A
TROUBLE SHOOTING TABLE (Continued)
No
pic
ture
an
d s
ou
nd
No
co
lor
No
TV
co
lor
No
S-V
IDE
O c
olo
r
Yes
No
Do
F37
01 a
nd F
3702
fu
nctio
n?
Che
ck a
ll th
e se
tting
s on
the
mic
ropr
oces
sor’s
adj
ust p
roce
ss m
enu.
No
Are
sec
onda
ry o
utpu
ts
(+38
V, +
16V,
+9V
, +5V
, -8V
) of
T70
1 as
spe
cifie
d?
Yes
Are
the
osci
llatio
n w
avef
orm
at
T70
1’s
prim
ary
side
as
spec
ified
?
Yes
No
Dis
conn
ect F
3701
and
F
3702
. Is
the
load
sid
e sh
ort-
circ
uite
d? Yes
No
Is a
ny o
f T70
1’s
prim
ary
side
, Q
701,
Q71
0 an
d S
4701
sh
ort-
circ
uite
d?
Che
ck J
3701
, its
per
iphe
ral
part
s an
d co
nnec
tion
cabl
e.
Rep
lace
F37
01 a
nd F
3702
.
Che
ck S
4701
and
co
nnec
tion
cabl
e.
Che
ck th
e se
cond
ary-
side
lo
ad o
f T70
1.
Flu
ore
scen
t la
mp
fai
lure
Yes
No
Doe
s F
3751
func
tion?
Yes
No
Is P
in (
34)
of IC
1201
at “
H”?
Yes
No
Are
the
osci
llatio
n w
avef
orm
s at
the
prim
ary
side
of T
751
and
T75
2 as
spe
cifie
d?
Yes
Rep
lace
F37
51.
No
Is in
put a
t Pin
(71
) of
IC80
2 as
spe
cifie
d?C
heck
SC
3301
, SC
line
and
pe
riphe
ral p
arts
.
Yes
Che
ck th
e lin
e, IC
1201
and
its
per
iphe
ral p
arts
.
Che
ck Q
751,
Q75
2, T
751,
T
752,
Q75
3 an
d th
eir
perip
hera
l par
ts.
Rep
lace
the
fluor
esce
nt la
mp
and
chec
k th
e os
cilla
tion
wav
efor
m a
gain
.
No
VID
EO
co
lor
Che
ck a
ll th
e se
tting
s on
the
mic
ropr
oces
sor’s
adj
ust p
roce
ss m
enu.
14
LC-10A2H-S/ALC-10A2M-S/A
TROUBLE SHOOTING TABLE (Continued)
No
so
un
d
fro
m
sp
eakers Yes
No
Is P
in (
53)
of
IC2001 a
t “L
”?
Check
all
the s
ettin
gs o
n the m
icro
pro
cessor’s a
dju
st
pro
cess m
enu.
No
so
un
d
No
Are
outp
uts
at
Pin
s (
1)
and (
7)
of IC
903 a
s
specifie
d? Y
es
No
Are
inputs
and
outp
uts
of
IC303 a
s
specifie
d? Y
es
No
Are
inputs
at
Pin
s (
5)
and (
8)
as w
ell
as
outp
uts
at P
ins
(2)
and (
11),
all
of IC
301, as
specifie
d?
Muting e
ffect is
on. C
heck
the
FS
MU
lin
e.
Check
IC
901,
IC903 a
nd their
peri
phera
l part
s.
Check
IC
303
and its
peri
phera
l part
s.
Check
the lin
e
in q
uestion,
IC303 a
nd its
peri
phera
l part
s.
Yes
Check
the
speake
rs a
nd
their p
eri
phera
l p
art
s.
No
so
un
d
fro
m
head
ph
on
e
Yes
No
Is P
in (
55)
of
IC2001 a
t “L
”?
Check
the
headphone a
nd
its p
eri
phera
l part
s.
Check
Q306,
J3405 a
nd their
peri
phera
l part
s.
No
so
un
d
fro
m o
utp
ut
lin
e
Yes
No
Is P
in (
52)
of
IC2001 a
t “L
”?
No
Are
outp
uts
at
Pin
s (
1)
and (
7)
of IC
902 a
s
specifie
d? Y
es
Check
the lin
e
in q
uestion.
Check
the
LM
UT
E lin
e.
Check
IC
902
and its
peri
phera
l part
s.
TV
so
un
d
failu
re
Yes
No
Is o
utp
ut at P
in
(16)
of tu
ner
as
specifie
d?
No
Is input at P
in
(60)
of IC
901
as s
pecifie
d?
Check
the
tuner
and its
peri
phera
l part
s.
Check
IC
901,
Q3301, Q
3204,
Q3205 a
nd
their p
eri
phera
l part
s.
28
LC-10A2H-S/ALC-10A2M-S/A
87 109654321
A
B
C
D
E
F
G
H
654321
A
B
C
D
E
F
G
H
CHASSIS LAYOUT !"#$%
MAIN Unit (Side-A)
MAIN Unit (Side-A)
29
LC-10A2H-S/ALC-10A2M-S/A
1716 1918151413121110 654321
A
B
C
D
E
F
G
H TERMINAL Unit
OPERATION Unit (Side-A)
OPERATION Unit (Side-B)
LED Unit
30
LC-10A2H-S/ALC-10A2M-S/A
87 109654321
A
B
C
D
E
F
G
H
654321
A
B
C
D
E
F
G
H
BLOCK DIAGRAM !"
31
LC-10A2H-S/ALC-10A2M-S/A
1716 1918151413121110
DESCRIPTION OF SCHEMATICDIAGRAM
VOLTAGE MEASUREMENT CONDITION:1. When the exclusive-use AC adapter is used, the colour
bar signal of colour bar generator for service is input toget the normal screen. When the audio is minimized,the voltage value is measured with the 20 kΩ/V tester.
WAVEFORM MEASUREMENT CONDITION:1. When the exclusive-use AC adapter is used, the colour
density, lightness and colour hue are set to the centerposition, and the signal of colour bar generator forservice is observed to get waveform.The wave form test point is indicated with the mark( ) in the wiring diagram.
INDICATION OF RESISTOR & CAPACITOR:
RESISTOR1. The unit of resistance “Ω” is omitted.
(K=kΩ=1000 Ω, M=MΩ).2. All resistors are ± 5%, unless otherwise noted.
(J= ± 5%, F= ± 1%, D= ± 0.5%)3. All resistors are Carbon type, unless otherwise noted.
C : Solid W : CementS : Oxide Film T : SpecialN : Metal Coating
CAPACITOR1. All capacitors are mF, unless otherwise noted.
(P=pF=mmF).2. All capacitors are Ceramic type, unless otherwise
CAUTION:This circuit diagram is original one, therefore there may be aslight difference from yours.
IMPORTANT SAFETY NOTICE:PARTS MARKED WITH “å” ( )AREIMPORTANT FOR MAINTAINING THE SAFETY OFTHE SET. BE SURE TO REPLACE THESE PARTSWITH SPECIFIED ONES FOR MAINTAINING THESAFETY AND PERFORMANCE OF THE SET.
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
44
LC-10A2H-S/ALC-10A2M-S/A
PARTS LISTPARTS REPLACEMENT
Replacement parts which have these special safety characteristicsidentified in this manual: electrical components having such featuresare identified by "å" in the Replacement Parts Lists.The use of a substitute replacement part which does not have thesame safety characteristics as the factory recommended replace-ment parts shown in this service manual may create shock, fire orother hazards.
"HOW TO ORDER REPLACEMENT PARTS"To have your order filled promptly and correctly, please furnish thefollowing informations.
DUNTKA077FE01 – MAIN Unit (LC-10A2H-A/S) —DUNTKA077FE02 – MAIN Unit (LC-10A2M-A/S) —DUNTKA078DE01 – TERMINAL Unit —
(LC-10A2H-A/S)DUNTKA078DE02 – TERMINAL Unit —
(LC-10A2M-A/S)DUNTKA079DE01 – OPERATION Unit —
(LC-10A2H-A/S)DUNTKA079DE02 – OPERATION Unit —
(LC-10A2M-A/S)DUNTKA080DE01 – LED Unit (LC-10A2H-A/S) —DUNTKA080DE02 – LED Unit (LC-10A2M-A/S) —DUNTKA081DE01 – RELAY Unit (LC-10A2H-A/S) —DUNTKA081DE02 – RELAY Unit (LC-10A2M-A/S)—
DUNTKA077FE01 (LC-10A2H-A/S)DUNTKA077FE02 (LC-10A2M-A/S)MAIN UNIT
1 CCABA2397CE02 J Front Cabinet Ass’y BE(LC-10A2-HA/MA)
1 CCABA2397CE01 J Front Cabinet Ass’y BE(LC-10A2-HS/MS)
1-1 Not Available – Front Cabinet —1-2 GCOVA1850CEKA J Cover, for R/C Receiver AG1-3 GCOVA1817CESA J Cover, for LED AE1-4 HBDGB3133CESD J Badge, ”SHARP” AG
(LC-10A2-HA/MA)1-4 HBDGB3133CESK J Badge, "SHARP" AG
(LC-10A2-HS/MS)1-5 HDECA0200CESB J Decoration Plate AK
(LC-10A2-HA/MA)1-5 HDECA0200CESA J Decoration Plate AK
No part of this publication may be reproduced,stored in a retrieval system, or transmitted inany form or by any means, electronic, mechanical,photocopying, recording, or otherwise, withoutprior written permission of the publisher.
SHARP CORPORATIONAV Systems GroupQuality & Reliability Control CenterYaita, Tochigi 329-2193, Japan