APPLICATION Compact single-axis robots TRANSERVO Single-axis robots FLIP-X Linear motor single-axis robots PHASER Cartesian robots XY-X SCARA robots YK-X Pick & place robots YP-X CLEAN CONTROLLER INFORMATION 438 Robot positioner Pulse string driver Robot controller iVY/ Electric gripper Option Features 1 Main operation patterns Normal operation Merge operation Output pattern Moves to the target position relative to the origin point and completes positioning. Moves from the current position just by a distance specified in point data and completes positioning. Moves while pushing at a preset push force. Pushing starts after decelerating at a distance equal to “Near width (N)” from the target position. P1 Position Moves to a specified coordinate position. P1 Current position Moves a specified distance from the current position P1 Pushes at a fixed thrust P1 Decelerates and then pushes N Speed ABS (absolute) operation Pushing operation INC (incremental) operation Pushing after decelerating Moves to multiple points in succession. If different speeds were set, then the speeds are changed without decelerating and stopping to continue point-to-point operation. P1 P2 Changes speed with no deceleration Merge operation Zone for external I/O output can be set for each point. P1 Output turns ON when a specified zone is entered ON OFF “Near width” output zone can be set for each point as a position margin zone where “positioning complete” signal is to be output. P1 Specify position margin zone. Zone output “Near width” output 2 Detailed data can be set for each point Settings such as acceleration, deceleration, zone output range, and position margin zone can be set for each point. Different operations can be easily specified by combining these settings with the above operation patterns. Setting items Setting item Description 1 Run type Specifies operation pattern such as ABS, INC, positioning, push, and point-to-point link. 2 Position Specifies position or distance to move. 3 Speed Specifies maximum speed during operation. 4 Accel. Specifies acceleration during operation. 5 Decel. Specifies deceleration during operation (Percentage of acceleration) 6 Push Specifies motor current limitation during pushing operation. 7 Zone (-) Specifies upper and lower limits of “personal zone” for each point data. 8 Zone (+) 9 Near width Specifies position margin zone where “near width” output should turn on. 10 Jump Specifies next movement destination after positioning or linked destination for point-to-point operation. 11 Flag Specifies stop mode and others. 12 Timer Specifies the waiting time (delay) after positioning completion. Note:Acceleration and deceleration can be set in easy-to-understand percentage (%) units (standard setup) or in SI units (custom setup) which make it easy to calculate the cycle time. 3 Maximum acceleration auto setting Acceleration is a critical parameter that determines how long the robot can continue operating (or service life). In worst cases, setting the acceleration too high may cause the robot to breakdown after a short time. On the TS series, the maximum acceleration is finely set by taking into account the service life span of the motor output and the guide for each robot model and payload. This eliminates any worry about setting the acceleration too high by mistake. 4 Full range of monitor functions P.454 The TS-Manager developed exclusively for the TS series not only does data write, edit, backup tasks and parameter settings but also comes loaded with cycle-time, simulator, and monitor functions of all types. A run-distance monitor for maintenance use is provided as a standard unit feature. Design emphasizes easy, user-friendly operation. Main monitor displays · Position · Current · Voltage · Input information · Output information · Speed · Load factor · Temperature 5 Direct positioning command “Direct positioning command” is provided that performs the positioning operation by specifying the position and speed data directly for the remote command. The positioning data can be handled by the control unit and the positioning operation can be performed by one command. The programming of the control unit can be constructed simply. WIN0 WIN1 WIN2 WIN3 Command Speed data Position data Position and speed data designations and positioning command are transmitted in the batch mode. Single axis TS-S2/TS-SH/TS-X/TS-P TS series TS series are positioner type controllers that only performs point trace. No program is needed. Operation is simple. After setting point data, specify the point number and enter a START signal from host controller such as a PLC. Positioning or pushing operation then begins. CE compliance Robot positioner TS-S2 TS-X TS-SH TS-P
11
Embed
TS series TS-S2/TS-SH/TS-X/TS-P · General specifications Operating temperature / Operating humidityStorage temperature/ Storage humidity 0°C to 40°C, 35% to 85%RH (non-condensing)-10°C
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
Transcript
APPLICATION
Co
mp
act
sing
le-a
xis rob
ots
TRAN
SERVOS
ing
le-a
xis rob
ots
FLIP-X
Lin
ea
r mo
tor
sing
le-a
xis rob
ots
PHA
SER
Ca
rtesia
nro
bo
ts
XY-X
SC
AR
Aro
bo
ts
YK
-X
Pick &
pla
cero
bo
ts Y
P-XC
LEAN
CON
TROLLER
INFORM
ATION
438
Ro
bo
t p
ositio
ne
rP
ulse string driver
Ro
bo
tco
ntro
ller
iVY
/E
lectric
grip
pe
rO
ptio
n
Features
1 Main operation patterns
Normal operation Merge operation Output pattern
Moves to the target position relative to the origin point and completes positioning.
Moves from the current position just by a distance specified in point data and completes positioning.
Moves while pushing at a preset push force.
Pushing starts after decelerating at a distance equal to “Near width (N)” from the target position.
P1 Position
Moves to a specified coordinate position.
P1Current position
Moves a specified distance from the current position
P1
Pushes at a fixed thrust
P1
Decelerates and then pushes
N
Speed
AB
S (absolute) operationP
us
hin
g o
pe
ratio
n
INC (increm
ental) operationPushing after decelerating
Moves to multiple points in succession. If different speeds were set, then the speeds are changed without decelerating and stopping to continue point-to-point operation.
P1 P2
Changes speed with no deceleration
Me
rge o
pe
ratio
n
Zone for external I/O output can be set for each point.
P1
Output turns ON when a specified zone is entered
ON OFF
“Near width” output zone can be set for each point as a position margin zone where “positioning complete” signal is to be output.
P1
Specify position margin zone.
Zo
ne o
utp
ut
“Ne
ar w
idth
” ou
tpu
t
2 Detailed data can be set for each pointSettings such as acceleration, deceleration, zone output range, and position margin zone can be set for each point. Different operations can be easily specified by combining these settings with the above operation patterns.
Setting itemsSetting item Description
1 Run type Specifies operation pattern such as ABS, INC, positioning, push, and point-to-point link.
2 Position Specifies position or distance to move.3 Speed Specifies maximum speed during operation.4 Accel. Specifies acceleration during operation.
5 Decel. Specifies deceleration during operation (Percentage of acceleration)
6 Push Specifies motor current limitation during pushing operation.
7 Zone (-) Specifies upper and lower limits of “personal zone” for each point data.8 Zone (+)
9 Near width Specifies position margin zone where “near width” output should turn on.
10 Jump Specifies next movement destination after positioning or linked destination for point-to-point operation.
11 Flag Specifies stop mode and others.
12 Timer Specifies the waiting time (delay) after positioning completion.
Note:Acceleration and deceleration can be set in easy-to-understand percentage (%) units (standard setup) or in SI units (custom setup) which make it easy to calculate the cycle time.
3 Maximum acceleration auto settingAcceleration is a critical parameter that determines how long the robot can continue operating (or service life). In worst cases, setting the acceleration too high may cause the robot to breakdown after a short time.On the TS series, the maximum acceleration is finely set by taking into account the service life span of the motor output and the guide for each robot model and payload. This eliminates any worry about setting the acceleration too high by mistake.
4 Full range of monitor functions P.454
The TS-Manager developed exclusively for the TS series not only does data write, edit, backup tasks and parameter settings but also comes loaded with cycle-time, simulator, and monitor functions of all types. A run-distance monitor for maintenance use is provided as a standard unit feature. Design emphasizes easy, user-friendly operation.
Main monitor displays
· Position
· Current
· Voltage
· Input information
· Output information
· Speed
· Load factor
· Temperature
5 Direct positioning command“Direct positioning command” is provided that performs the positioning operation by specifying the position and speed data directly for the remote command.The positioning data can be handled by the control unit and the positioning operation can be performed by one command. The programming of the control unit can be constructed simply.
WIN0 WIN1 WIN2 WIN3
Command Speed data Position data
Position and speed data designations and positioning command are transmitted in the batch mode.
Single axis
TS-S2/TS-SH/TS-X/TS-PTS series
TS series are positioner type controllers that only performs point trace. No program is needed.Operation is simple. After setting point data, specify the point number and enter a START signal from host controller such as a PLC. Positioning or pushing operation then begins.
CE compliance Robot positioner
TS-S2 TS-XTS-SH TS-P
APPLICATION
Co
mp
act
sing
le-a
xis rob
ots
TRAN
SERVOS
ing
le-a
xis rob
ots
FLIP-X
Lin
ea
r mo
tor
sing
le-a
xis rob
ots
PHA
SER
Ca
rtesia
nro
bo
ts
XY-X
SC
AR
Aro
bo
ts
YK
-X
Pick &
pla
cero
bo
ts YP-X
CLEA
NCO
NTRO
LLERINFO
RMATIO
N
439
Ro
bo
t p
ositio
ne
rP
ulse string driver
Ro
bo
tco
ntro
ller
iVY
/E
lectric
grip
pe
rO
ptio
n
HT1
or
TS-Manager
Up to 16 controllers
TS-S2/TS-SH/TS-X/TS-P
Ordering method
TS-S2 / TS-SH (TRANSERVO)
Robot positioner Type I/O Battery Note 1
S2: TS-S2 No entry: Standard NP: NPN B: With battery(Absolute model)SH: TS-SH S: Sensor PN: PNP
Note 1. Battery can only be selected for TS-SH. (Not provided for TS-S2).
TS-X/TS-P (FLIP-X / PHASER)
Controller Driver: Power-supply voltage/ Power capacity Regenerative unit LCD monitor Input/Output
Selection Battery Note 2
TSX: TS-X 105: 100V / 100W more less No entry: None No entry: None NP: NPN B: With battery(Absolute model)TSP: TS-P 110: 100V / 200W R: With RGT L: With LCD PN: PNP
205: 200V / 100W more less R: With RGU-2 CC: CC-Link N: None(Incremental model)210: 200V / 200W DN: DeviceNetTM
220: 200V / 400 to 600W EP: EtherNet/IPTM
GW: With no I/O board
Note 2. Battery can only be selected for TS-X. (Not provided for TS-P).
Some specifications are automatically determined by the robot model.
(1) Regenerative unit is needed if using in a perpendicular position and movement stroke is 700mm or more.(2) Regenerative unit is needed if using in a perpendicular position.(3) Regenerative unit is needed if using in a perpendicular position, using at maximum speeds exceeding 1000mm per second, or if using high leads (40).(4) Regenerative unit is needed if using at maximum speeds exceeding 1000mm per second.(5) Regenerative unit is needed if using at maximum speeds exceeding 1250mm per second.(6) Regenerative unit is needed if using at maximum speeds exceeding 750mm per second.
One controller installed on the field network board manages up to four I/O interfaces through the daisy chain connection. This does not require any excess devices and ensures the control in the same way as one board is installed into one unit while reducing the network cost.
Conventional NEW
4 CC-Link boards are needed. Daisy chain connection
Field network
Host unit(Applicable to field network)
CC-Link4 boards are reduced to
1 board.
Network board is required for each controller. Only one network board manages up to 4 units.
This function allows monitoring the various data design and operation status of any controller connected via daisy chain from one PC or handy terminal.
Instruction manuals can be downloaded from our company website. Please use the following for more detailed information.http://global.yamaha-motor.com/business/robot/
Point type setting (1) Standard setting: Set speed and acceleration in percent of the respective maximum settings. (2) Custom setting: Set speed and acceleration in SI units.
Point teaching method Manual data input (coordinates input), Teaching, Direct teaching
Ext
erna
l inp
ut/o
utpu
t I/O interface Selectable from the following: NPN, PNP, CC-Link, DeviceNetTM, EtherNet/IPTM
InputServo ON (SERVO), reset (RESET), start (START), interlock (/LOCK) origin search (ORG), manual mode (MANUAL), jog motion - (JOG-), jog motion + (JOG+), Point number selection (PIN0 to PIN7)
Output Servo status (SRV-S), alarm (/ALM), operation end (END), operation in-progress (BUSY), control outputs (OUT0 to 3), Point number output 0 to 7 (POUT0 to POUT7)
External communications RS-232C 1CH
Safety circuit Emergency stop input, emergency stop contact output (1 system: When the HT1 is used.)
ns Operating temperature / Operating humidity 0°C to 40°C, 35% to 85%RH (non-condensing)
Storage temperature/ Storage humidity -10°C to 65°C, 10% to 85%RH (non-condensing)
Atmosphere Indoor location not exposed to direct sunlight. No corrosive , flammable gases, oil mist, or dust particles
Anti-vibration All XYZ directions 10 to 57Hz unidirectional amplitude 0.075mm 57 to 150Hz 9.8m/s2
Protective functions Position detection error, temperature error, overload, overvoltage, low voltage, excessive position deviation, overcurrent, motor current error, motor cable faulty wiring, Excitation power failure error Note 1
Note 1. The excitation power failure error is a protection function that is available only in TS-SH.
Point type setting (1) Standard setting: Set speed and acceleration in percent of the respective maximum settings. (2) Custom setting: Set speed and acceleration in SI units.
Point teaching method Manual data input (coordinates input) , Teaching, Direct teaching
Ext
ern
al i
np
ut/
ou
tpu
t I/O interface Selectable from the following: NPN, PNP, CC-Link, DeviceNetTM, EtherNet/IPTM
InputServo ON (SERVO), reset (RESET), start (START), interlock (/LOCK) origin search (ORG), manual mode (MANUAL), jog motion - (JOG-), jog motion + (JOG+), Point number selection (PIN0 to PIN7)
Output Servo status (SRV-S), alarm (/ALM), operation end (END), operation in-progress (BUSY), control outputs (OUT0 to 3), Point number output 0 to 7 (POUT0 to POUT7)
External communications RS-232C 1CH
Power supply for brake DC24V +/-10% 300mA (prepared by the customer)
Safety circuit Emergency stop input, main power input ready output, emergency stop contact output (1 system: When the HT1 is used.)
ns Operating temperature / Operating humidity 0°C to 40°C, 35% to 85%RH (non-condensing)
Storage temperature / Storage humidity -10°C to 65°C, 10% to 85%RH (non-condensing)
Atmosphere Indoor location not exposed to direct sunlight. No corrosive , flammable gases, oil mist, or dust particles
Anti-vibration All XYZ directions 10 to 57Hz unidirectional amplitude 0.075mm 57 to 150Hz 9.8m/s2
Protective functions Position detection error, power module error, temperature error, overload, overvoltage, low voltage, excessive position deviation, overcurrent, motor current error
Protective structure IP20
APPLICATION
Co
mp
act
sing
le-a
xis rob
ots
TRAN
SERVOS
ing
le-a
xis rob
ots
FLIP-X
Lin
ea
r mo
tor
sing
le-a
xis rob
ots
PHA
SER
Ca
rtesia
nro
bo
ts
XY-X
SC
AR
Aro
bo
ts
YK
-X
Pick &
pla
cero
bo
ts YP-X
CLEA
NCO
NTRO
LLERINFO
RMATIO
N
441
Ro
bo
t p
ositio
ne
rP
ulse string driver
Ro
bo
tco
ntro
ller
iVY
/E
lectric
grip
pe
rO
ptio
nTS-S2/TS-SH/TS-X/TS-P
TS-S2 / TS-SH part names
Controller
Communication connector 1(COM1)
Connector for connection to HT1or a personal computer. Robot I/O
connector (ROB I/O)Dedicated connector for robot I/O signals such as position signals and origin sensor signals, etc.
I/O connector (I/O)Selectable at time of purchase as:
NPN,PNP, CC-Link, DeviceNetTM or EtherNet/IPTM.
Rating nameplate(on side face of unit body)
Serial No.
Communicationconnector 2 (COM2)
Connector for the daisy-chainconnection cable.
Status indicator lamps(PWR, ERR)The controller status is indicatedby LED lamps.
Power supply connectorConnector for main power and
control power input.
TS-X / TS-P part names
Communicationconnector 2 (COM2)Connector for the daisy-chain or LCD monitor connection.Absolute battery connector (BAT)Connector for the absolutebattery connection. (only for TS-X)
ControllerUnit's top cover inan open condition
Serial No.
Communication connector 1(COM1)Connector for connection to HT1or a personal computer.Robot I/O connector (ROB I/O)Dedicated connector for robot I/Osignals such as position signalsand origin sensor signals, etc.Motor connector (MOTOR)Connector for the servo motor'spower line connection.I/O connector (I/O)Connector type is selected NPN, PNP, CC-Link, DeviceNetTM or EtherNet/IPTM when purchased.Regenerative unit connector(RGEN)Connector for the regenerativeunit connection.
Rating nameplate(on side face of unit body)
Status indicator lamps(PWR, ERR)The controller status is indicatedby LED lamps.
Power supply connectorConnector for main power and control power input.
EXT connector(bottom face of unit body) Connector for brake power input and external safety circuit inputs/outputs.
Regenerative unit RGT/RGU-2
Regenerative unit RGT
RGEN
Dimensions
2 12030
15
142
152
162
ϕ5.5
R2.75
5
Basic specifications
Item RGTModel KCA-M4107-0A
Dimensions W30 × H142 × D118mm (Not including installation stay)
Weight 470g
Regenerative voltage Approx. 420V or more
Regenerative stop voltage Approx. 380V or less
Accessory Cable for connection with controller (300mm)
Note. Always leave an empty space (gap of about 20mm) between this unit and the adjacent controller. Also, always use the dedicated cable when connecting the controller.
15740
165.5
250
290
265
Regenerative unit RGU-2
Dimensions
Basic specifications
Item RGU-2 TS-P Model KCA-M4107-2A (Including accessory)
Dimensions W40 × H250 × D157mm
Weight 0.9kg
Regenerative voltage Approx. 380V or more
Regenerative stop voltage Approx. 360V or less
Accessory Cable for connection with controller (300mm)
Note. Always leave an empty space (gap of about 20mm) between this unit and the adjacent controller. Also, always use the dedicated cable when connecting the controller.
58 131(90)
162
167
(8)
152
5
5.4
R
53
4
ϕ5.4
EXT connector
TS-X/TS-P (105/110/205/210)
131
167
(90)
162
5870
4
53
R
5.4
5
ϕ5.4
152
(8)
EXT connector
TS-X/TS-P (220)
Installation conditions
• Install the TS-S2/TS-SH/TS-X/TS-P inside the control panel.
• Install the TS-S2/TS-SH/TS-X/TS-P on a vertical wall.
• Install the TS-S2/TS-SH/TS-X/TS-P in a well ventilated location, with space on all sides of the TS-S2/TS-SH/TS-X/TS-P (See fig. at right.).
• Ambient temperature : 0 to 40˚C
• Ambient humidity : 35 to 85% RH (no condensation)
N1
RGEN
LCOM1
I/OROB
CHARGE
200VL1
MOTOR
I/O
N
PWR
ERR
20mmor more
20mmor more
20mmor more
20mmor more
TS-X/TS-PTS-S2/TS-SH
PWR
ERR
COM2
COM1
ROBI/O
I/O
ES1ES2ES-
MP24VCP24V
0V
20mmor more
20mmor more
10mmor more
10mmor more
TS-S2 / TS-SH / TS-X / TS-P dimensions
TS-SH
(70) 123
152
5
25
ϕ4.5
4.5
30
RR
4
(12)
162
35.2
: DIN
rail
widt
h is
35m
m.
4
80.7
: Cen
ter p
ositio
n of
DIN
rail
152
5
82(70)30
5
162
515
2
25
ϕ4.5
4.5
R
TS-S2
Instruction manuals can be downloaded from our company website. Please use the following for more detailed information.http://global.yamaha-motor.com/business/robot/
APPLICATION
Co
mp
act
sing
le-a
xis rob
ots
TRAN
SERVOS
ing
le-a
xis rob
ots
FLIP-X
Lin
ea
r mo
tor
sing
le-a
xis rob
ots
PHA
SER
Ca
rtesia
nro
bo
ts
XY-X
SC
AR
Aro
bo
ts
YK
-X
Pick &
pla
cero
bo
ts Y
P-XC
LEAN
CON
TROLLER
INFORM
ATION
442
Ro
bo
t p
ositio
ne
rP
ulse string driver
Ro
bo
tco
ntro
ller
iVY
/E
lectric
grip
pe
rO
ptio
n
TS-S2/TS-SH/TS-X/TS-P
Data overview
Point data and parameter data settings must be specified in order to operate a robot from a TS series controller.
Point data
The point data used in positioning operations includes items such as the “RUN type”, “Position”, and “Speed”, etc.Up to 255 points (P1 to P255) can be registered. There are two point data setting types: “Standard setting” type that automatically defines optimal positioning simply by specifying the payload and “Custom setting” type that allows setting the speed (mm/s) and acceleration (m/s2) in SI units. Select the desired setting type according to the application.
Parameter data
Parameter data is divided into the following categories: “RUN parameters”, “I/O parameters”, “option parameters”, and “servo parameters”.
Data structure
P1 to P255
RUN typePositionSpeedAccel.Decel.Push
Data Point data
Parameter data
123456
Zone (-)Zone (+)Near widthJumpFlagTimer
789101112
K1 to K20
RUN parameter
K21 to K39
I/O parameter
K80 to K99
Option parameter
K40 to K79, K100 to ...
Servo parameter
Sets the point data to be used in positioning. Select the desiredsetting type (“standard setting” or “custom setting”) according to the application.
Specifies parameter settings related to positioning and return to-origin operations.
Specifies parameter settings related to terminal assignments and I/O function selection.
Specifies parameter settings related to options such as CC-Link, etc.
Specifies parameter settings specified to the connected robot. These parameters are specified during initial processing.
(1) Standard settingOptimum positioning is provided simply by specifying the payload.
(2) Custom settingSpeed and acceleration can be set in SI units.
Point data
Point data item list
P1 to P255Item Description
1 RUN type Specifies the positioning operation pattern.
2 PositionSpecifies the positioning target position or movement amount.
3 Speed Specifies the positioning speed.4 Accel. Specifies the positioning acceleration.
5 Decel.Specifies the positioning deceleration (as a percentage of the acceleration).
6 PushSpecifies the electrical current limit value for “Push” operations.
7 Zone (-)Specifies the “personal zone” output range.
8 Zone (+)
9 Near widthSpecifies the “near width” zone (distance toler-ance relative to target position).
10 JumpSpecifies the next movement destination, or the next merge operation merge destination point No. follow-ing positioning completion.
11 FlagSpecifies other information related to the posi-tioning operation.
12 TimerSpecifies the waiting time (delay) after position-ing completion.
“Standard setting” and “custom setting”There are 2 setting types for point data (“standard setting” or “custom set-ting”). Select the desired setting type according to the application.The maximum number of setting points for both setting types is 255 points (P1 to P255).
Setting Type Description
Standard setting
Optimum positioning is provided simply by specifying the payload.This setting type is well-suited to assembly and transport applications.
Custom setting
Allows changing the speed and acceleration in SI units so the desired positioning opera-tion can be set.This setting type is suited for machining and inspection systems.
Cautions on TS-S2 / TS-SH
For the RF type sensor specifications, the controllers “TS-S2” and “TS-SH” become “TS-S2S” and “TS-SHS”, respectively.
TS-S2 / TS-SH (Standard specifications)
“BK” label is affixed to the front of the controller.
TS-S2S / TS-SHS (Sensor specifications)
“SENSOR” label is affixed to the front of the controller.(Be aware that “TS-S2S” is affixed to the front of the controller.)
PNPInput 16 points, 24VDC +/-10%, 5.5mA/point, minus commonOutput 16 points, 24VDC +/-10%, 50mA/point, source type
CC-LinkCC-Link Ver.1.10 compatible, Remote station device (1 node)
DeviceNetTM DeviceNetTM Slave 1 node
EtherNet/IPTM EtherNet/IPTM adapter (2 ports)
Instruction manuals can be downloaded from our company website. Please use the following for more detailed information.http://global.yamaha-motor.com/business/robot/
APPLICATION
Co
mp
act
sing
le-a
xis rob
ots
TRAN
SERVOS
ing
le-a
xis rob
ots
FLIP-X
Lin
ea
r mo
tor
sing
le-a
xis rob
ots
PHA
SER
Ca
rtesia
nro
bo
ts
XY-X
SC
AR
Aro
bo
ts
YK
-X
Pick &
pla
cero
bo
ts Y
P-XC
LEAN
CON
TROLLER
INFORM
ATION
444
Ro
bo
t p
ositio
ne
rP
ulse string driver
Ro
bo
tco
ntro
ller
iVY
/E
lectric
grip
pe
rO
ptio
n
I/O signals (NPN / PNP)
No. Signal Name Description No. Signal Name Description
A1+COM
I/O power input, positive common (24VDC +/-10%)
B1 POUT0
Ou
tpu
ts
Point No. outputs
A2 B2 POUT1
A3 NCNo connection
B3 POUT2
A4 NC B4 POUT3
A5 PIN0
Inp
uts
Point No. select
B5 POUT4
A6 PIN1 B6 POUT5
A7 PIN2 B7 POUT6
A8 PIN3 B8 POUT7
A9 PIN4 B9 OUT0 OUT0 to OUT3 assignments include: • Zone output• Personal zone output• MANUAL mode status• Return-to-origin end status• NEAR output• Movement-in-progress• Push status• Warning output
A10 PIN5 B10 OUT1
A11 PIN6 B11 OUT2
A12 PIN7 B12 OUT3
A13 JOG+ JOG movement (+ direction) B13 BUSY Operation-in-progress
A14 JOG- JOG movement (- direction) B14 END Operation-end
A15 MANUAL MANUAL mode B15 /ALM Alarm
A16 ORG Return-to-origin B16 SRV-S Servo status
A17 /LOCK Interlock B17 NCNo connection
A18 START Start B18 NC
A19 RESET Reset B19-COM I/O power input, negative common (0V)
A20 SERVO Servo ON B20
TS-S2/TS-SH/TS-X/TS-P
NPN type I/O circuit details
Input circuit
DC24VLogiccircuit
Internalcircuit
4.7kΩ
+COM
Input
-COM
Type :
Load :
DC input (plus common type)Photo-coupler isolation format24VDC +/- 10%, 5.1mAOFF voltage : 19.6Vmin (1.0mA)ON voltage : 4.9Vmax (4.0mA)
Output circuit
DC24V
Logiccircuit
Internalcircuit
OutputLoad
+COM
-COM
Type :
Load :
NPN open collector output(Minus common type)Photo-coupler isolation format24VDC, 50mA/point
PNP type I/O circuit details
Input circuit
DC24V
Logiccircuit
Internalcircuit
4.7kΩ
Input
+COM
-COM
Type :
Load :
DC input (minus common type)Photo-coupler isolation format24VDC +/- 10%, 5.5mAON voltage : 19.6Vmin (4.5mA)OFF voltage : 4.9Vmax (1.1mA)
Output circuit
DC24V
Logiccircuit
Internalcircuit
LoadOutput
+COM
-COM
Type :
Load :
PNP open collector output(Plus common type)Photo-coupler isolation format24VDC, 50mA/point
APPLICATION
Co
mp
act
sing
le-a
xis rob
ots
TRAN
SERVOS
ing
le-a
xis rob
ots
FLIP-X
Lin
ea
r mo
tor
sing
le-a
xis rob
ots
PHA
SER
Ca
rtesia
nro
bo
ts
XY-X
SC
AR
Aro
bo
ts
YK
-X
Pick &
pla
cero
bo
ts YP-X
CLEA
NCO
NTRO
LLERINFO
RMATIO
N
445
Ro
bo
t p
ositio
ne
rP
ulse string driver
Ro
bo
tco
ntro
ller
iVY
/E
lectric
grip
pe
rO
ptio
nTS-S2/TS-SH/TS-X/TS-P
Accessories and part options
Standard accessories
Options
Power connector
Model KCC-M4421-00
Power connector (AC100V specifications)
Model KCA-M5382-00
Power connector (AC200V specifications)
Model KAS-M5382-00
Handy terminal HT1 / HT1-D
Has graphic LCD display with backlight for easy viewing.
Enable switch – 3-positionCE marking Not supported Applicable
P.448
TS-Monitor (LCD monitor)
A liquid crystal display is integrated into this unit. It allows checking each operating state, current posi-tion, electrical current and voltage values, etc.
ModelFor TS-X KCA-M5119-00For TS-P KCA-M5119-10
P.447
Support software TS-Manager
Besides data writing, editing and backup functions, the TS-Manager also offers cycle time simulation and various types of monitor functions.
Note. This is a single connector type. (Insert two connectors into a branch-ing socket.)Note. The absolute battery is subject to wear and requires replacement.
If trouble occurs with the memory then remaining battery life is low so replace the absolute battery. The battery replacement period de-pends on usage conditions. But generally you should replace the battery after about 1 year counting the total time after connecting to the controller and left without turning on the power.
Instruction manuals can be downloaded from our company website. Please use the following for more detailed information.http://global.yamaha-motor.com/business/robot/
APPLICATION
Co
mp
act
sing
le-a
xis rob
ots
TRAN
SERVOS
ing
le-a
xis rob
ots
FLIP-X
Lin
ea
r mo
tor
sing
le-a
xis rob
ots
PHA
SER
Ca
rtesia
nro
bo
ts
XY-X
SC
AR
Aro
bo
ts
YK
-X
Pick &
pla
cero
bo
ts Y
P-XC
LEAN
CON
TROLLER
INFORM
ATION
446
Ro
bo
t p
ositio
ne
rP
ulse string driver
Ro
bo
tco
ntro
ller
iVY
/E
lectric
grip
pe
rO
ptio
n
Options
TS-S2/TS-SH/TS-X/TS-P
DIN rail mounting bracket (This bracket is provided in TS-SH as standard equipment.)
This Handy Terminal is a device that can perform any operation such as robot manual operation, point data edit, teaching, and parameter setting, etc. Has graphic LCD display with backlight for easy viewing.
Attaching a short strap or necklace strap here prevents dropping the HT1 while operating it or installing it onto equipment.
Strap holder
This is a liquid crystal display (LCD) screen with 32 characters × 10 lines (pixel display), showing the operation menus and various types of information.
LCD screen
Use these keys to select menus and edit various data.
Data edit keys
This cable connects to the controller. One end of this cable is terminated with an 8-pin MD connector (male). Plug this cable into the COM1 connector on the controller front panel.
Connector cable
Pressing this button during operation immediately stops robot movement. To release this button, turn it clockwise. Releasing this button also cancels emergency stop.
Emergency stop button
Use these keys to operate the robot for teaching or positioning, or to stop operation. The and keys are also provided to move the robot in jog mode.
Run/stop keys
HT1-D rear side
Use with remote safety circuits triggered by the emergency stop button or enable switch.
Safety connector (only on HT1-D)
This switch is effective for use with remote safety circuits. This switch cuts off the circuit when pressed or released but allows circuit operation when in the middle position.
Enable switch (only on HT1-D)
APPLICATION
Co
mp
act
sing
le-a
xis rob
ots
TRAN
SERVOS
ing
le-a
xis rob
ots
FLIP-X
Lin
ea
r mo
tor
sing
le-a
xis rob
ots
PHA
SER
Ca
rtesia
nro
bo
ts
XY-X
SC
AR
Aro
bo
ts
YK
-X
Pick &
pla
cero
bo
ts YP-X
CLEA
NCO
NTRO
LLERINFO
RMATIO
N
449
Ro
bo
t p
ositio
ne
rP
ulse string driver
Ro
bo
tco
ntro
ller
iVY
/E
lectric
grip
pe
rO
ptio
n
Option unit with networking functions that can be incorporated in YAMAHA robot controllers, TS-S2 / TS-SH / TS-X / TS-P.
As connection of the robot system and the se-quencer requires only one (4-wire) dedicated cable, it is possible to save wiring of the entire system, which contributes to efficient wiring work, reduction of installation and mainte-nance costs, etc.
16 input/outputs usable as I/O.
Operation occurs as a CC-Link remote device station, on a one-unit to one-station basis.
Remote commands can read or write point data and load each type of status.
Option unit with networking functions that can be incorporated in YAMAHA robot controllers, TS-S2 / TS-SH / TS-X / TS-P.
As connection of the robot system and the se-quencer requires only one (4-wire) dedicated cable, it is possible to reduce wiring of the entire system, which contributes to efficient wiring work, reduction of installation and main-tenance costs, etc.
16 input/outputs usable as I/O.
Operate as slave stations, with each unit oc-cupying 6 input and 6 output channels.
Remote commands can read or write point data and load each type of status.
Basic specifications for network modules CC-LinkItem Network modules CC-Link
Option unit with networking functions that can be incorporated in YAMAHA robot controllers, TS-S2 / TS-SH / TS-X / TS-P.
For connection of the robot system and the sequencer, the daisy chain connation can be constructed with a LAN cable (CAT5 or more) that is generally available on the market. As it is not necessary to use the hub, the wiring can be saved and the costs necessary to install the entire system can also be reduced.
Operate as adapters, with each unit occupying 6 input and 6 output channels.
Remote commands can read or write point data and load each type of status.
Basic specifications for network modules EtherNet/IPTM
Note. Supported by controller software version V1.10.121 or later. Necessary parameters can be set with the support tool, HT-1 (V1.13 or later) and TS-Manager (V1.3.3 or later).