2013-06-20 APTRANSCO 2012 ELECTRICAL Previous Paper APTRANSCO 2012 KEY ELECTRICAL 1. 1. A voltage waveform v(t)= 12 t2 is applied across a 1H inductor for t>=0 with initial current through it being zero. The current through the inductor for t>=0 is given by-----------(4t3) 2. Two incandescent light bulbs fo 40w and 60w rating are connected in series across the mains. Then--------(the 40 bulb glows brighter) 3. Given two coupled inductors L1 and L2, their mutual inductances M satisfies-----(M 4. Consider the star network. The resistance between terminals A and B with C open 6ohms, between terminals B and C with A open is 11ohms, and between terminals C and A with B open is 9ohms. Then ------------(Ra=2, Rb=4, Rc=7) 5. In a series RLC circuit at resonance, the magnitude of the voltage developed across the capacitor------( can be greater than the input voltage, however, it is 900 out of phase with the input voltage) 6. A two port device is defined by the following pair of quations: i1=2v1+v2 and i2=v1+v2 its impedance parameters (z11, z12, z21, z22) are-----(1,-1,-1,2) 7. The impulse response of an initially relaxed linear system is e-2tu(t).to produce a response of te-2tu(t), the input must be equal to--------(e-2t u(t)) 8. The no of roots on the equation 2s4+s3+3s2+5s+7=0
This document is posted to help you gain knowledge. Please leave a comment to let me know what you think about it! Share it to your friends and learn new things together.
1. A voltage waveform v(t)= 12 t2 is applied across a 1H inductor for t>=0 withinitial current through it being zero. The current through the inductor fort>=0 is given by-----------(4t3)
2. Two incandescent light bulbs fo 40w and 60w ratingare connected in series across the mains. Then--------(the 40 bulb glows brighter)
3. Given two coupled inductors L1 and L2, their mutualinductances M satisfies-----(M
4. Consider the star network. The resistance betweenterminals A and B with C open 6ohms, between terminals B and C with A open is11ohms, and between terminals C and A with B open is 9ohms. Then------------(Ra=2, Rb=4, Rc=7)
5. In a series RLC circuit at resonance, the magnitudeof the voltage developed across the capacitor------( can be greater than theinput voltage, however, it is 900 out of phase with the input voltage)
6. A two port device is defined by the following pairof quations:
i1=2v1+v2 and i2=v1+v2 its impedance parameters(z11, z12, z21, z22) are-----(1,-1,-1,2)
7. The impulse response of an initially relaxed linearsystem is e-2tu(t).to produce a response of
te-2tu(t), the input must be equalto--------(e-2t u(t))
8. The no of roots on the equation 2s4+s3+3s2+5s+7=0that lie in the right half of s plane is-------(2)
9. For a feedback control system of type 2, the steadystate error for a ramp input is-------(zero)
10. The output of a linear time invariant controlsystem is c(t) for a certain input r(t). if r(t) is modified by passing itthrough a block whose transfer function is e-s and then applied to the system,the modified output of the system would be-----------(c(t-1)u(t-1)
11. The phase lead compensation used to-----(decreasesboth rise time and overshoot)
12. Consider two buses connected by an impedance of(0+j5)ohm. The bus 1 voltage is 100/300 v, and bus 2 voltage is 100/00 v. the real and reactive power supplied by bus 1,resp are……….(1000w, 268 VAr)
13. For a fixed value of complex power flow in atransmission line having a sending end voltage V, the real power loss will beproportional to-----------(1/V2).
14. During a disturbance on a synchronous machine, therotor swings from A to B before finally settling down to a steady state atpoint C on the power angle curve. The speed of the machine during oscillationis synchronous at point(s)--------------------(A and B)
15. A 100 MVA, 11kv, 3 phase 50hz, 8 pole synchronousgenerator has an inertia constant H equal to 4 MJ/MVA. The stored energy in therotor of the generator at synchronous speed will be---(400MJ).
16. In a biased differential relay the bias is definedas a ratio of----------(operating coil current and restraining coil current))
17. Resistance switching is normally employedin------(ABCB)
18. The use of high speed circuit breakers----(improvessystem stability)
19. Keeping in view the cost and overall effectiveness,the following circuit breaker is best suited for capacitor bankswitching---(vacuum)
20. If the reference bus is changed in two load flowruns with the same system data and power obtained for reference bus taken asspecified P and Q in the latter run----------( the system losses will beunchanged but complex bus voltages will change.)
21. The gauss seidel load flow method has followingdisadvantages. Tick the incorrect statement------( unreliable convergence)
22. The torque speed characteristics of a repulsionmotor resembles which of the following dc motorcharacteristic------------(series)
23. Which type of motor is most suitable for computer
printer drive-----(stepper motor)
24. A 4 pole lap wound DC generator has a developedpower of P watts and voltage of E volts. Two adjacent brushes of the machineare removed as they are worn out. If the machine operates with the remainingbrushes, the developed voltage and power that can be obtained from the machineare----(E,P/4)
25. A 4 point starter is used to start and control thespeed of a -----------( dc shunt motor with field weakening control)
26. The function of oil in a transformer is-----( toprovide insulation and cooling)
27. The core flux of a practical transformer with aresistive load------------( is strictly constant with load changes)
28. In a transformer zero voltage regulation at fullload is----(possible at leading pf load)
29. A single phase transformer has a turns ratio of1:2, and is connected to a purely resistive load. The magnetizing current drawnis 1 A, and the secondary current is 1A. if core losses and leakage reactanceare neglected, the primary current is-(2.24A)
30. The low voltage winding of a 400/230V, single phase50hz transformer is to be connected to a 25hz, the supply voltage shouldbe-------(115V)
31. A 400/100V, 10 KVA two winding transformer isreconnected as an auto transformer is reconnected as an auto transformer acrossa suitable voltage source. The maximum rating of such an arrangement couldbe-----(50KVA)
32. When the supply voltage to an induction motor isreduced by 10%, the maximum torque will decrease by approximately-------(20%)
33. In case of a split phase motor, the phase shiftbetween currents in the two windings is around------(300)
34. Starting torque can be obtained in the case of asingle phase induction motor with identical main and auxiliary windings byconnecting-----( a capacitor in series with the auxiliary winding)
35. For a single phase capacitor start induction motorwhich of the following statements is valid---( the direction of rotation can bechanged by reversing the main winding terminals)
36. An induction motor having full load torque of 60zNmwhen delta connected develops a starting torque of 120Nm. For the same supplyvoltage, if the motor is changed to star-connection, the starting torquedeveloped will be-------(40NM)
37. During hunting of synchronous motor –(damper bardevelops torque)
38. The phase sequence of a three phase alternator willreverse if -------(the field current remains the same but the direction ofrotation is reversed)
39. The effect of stray magnetic fields on theactuating torque of a portable instrument is max when the operating filed ofthe instrument and the stray fields are-(parallel)
40. A current of -8+6
(sinwt+300)A is passed through threemeters. They are a center zero PMMC meter, true rms meter and MI instrument.The respective reading( in A) will be----(-8,10,10)
41. R1 and R2 are the opposite arms of a wheatstonebridge as are R3 and R, the source voltage is applied across R1 and R3 underbalanced conditions which one of the following is true---(R1=R2R3/R4)
42. A dc potentiometer is designed to measure up toabout 2v with a slide wire of 800mm. a standard cell of emf 1.18v obtainsbalance at 6010mm. a test cell is seen to obtain balance at 680mm. the emf ofthe test cell is-(1.34v)
43. The minimum number of wattmeters required tomeasure3 phase 3 wire or unbalanced power is—(2)
44. A reading of 120 is obtained when a standardinductor was connected in the circuit of a Q meter and the variable capacitoris adjusted to a value of 300pF. A lossless capacitor of unknown value C, isthen connected and the same reading was obtained when the variable capacitor isreadjusted to a value of 200pF. The value of Cx in pF is—(100)
45. The two inputs of a CRO are fed with the two
stationary periodic signals. In the X Y mode, the screen shows a figure whichchanges from ellipse to circle and back to ellipse with its major axis changingorientation slowly and repeatedly. The following inference can be made fromthis----------(there is a constant but small phase difference between thesignals)
46. SCR can be turned off—( anode current should beless than holding current)
47. The no. of pn junctions in SCR-----(3)
48. TRIAC is a—(antiparallel thyristors combination)
49. GTO can be turned off-(by using a negative currentpulse)
50. Which type of control is used for controlling theac drive by using thyristors--------(integral cycle)
51. In DC choppers the output voltage can be controlledby using FM technique varying--------( T , Toff constant)
52. In phase control rectifiers the output voltageripple can be controlled by—‘(load inductance)
53. Which is not a current controlleddevice-----(MOSFET)
54. Inverter function---------(DC to AC with variablefrequency)
55. In phase controlled rectifires free wheeling diodemakes-(load current continuation)
56. Dielectric heating application----(wood)
57. In induction heating the following is abnormallyhigh--------(frequency)
1. A voltage waveform v(t)= 12 t2 is applied across a 1H inductor for t>=0 withinitial current through it being zero. The current through the inductor fort>=0 is given by-----------(4t3)
2. Two incandescent light bulbs fo 40w and 60w rating
are connected in series across the mains. Then--------(the 40 bulb glows brighter)
3. Given two coupled inductors L1 and L2, their mutualinductances M satisfies-----(M
4. Consider the star network. The resistance betweenterminals A and B with C open 6ohms, between terminals B and C with A open is11ohms, and between terminals C and A with B open is 9ohms. Then------------(Ra=2, Rb=4, Rc=7)
5. In a series RLC circuit at resonance, the magnitudeof the voltage developed across the capacitor------( can be greater than theinput voltage, however, it is 900 out of phase with the input voltage)
6. A two port device is defined by the following pairof quations:
i1=2v1+v2 and i2=v1+v2 its impedance parameters(z11, z12, z21, z22) are-----(1,-1,-1,2)
7. The impulse response of an initially relaxed linearsystem is e-2tu(t).to produce a response of
te-2tu(t), the input must be equalto--------(e-2t u(t))
8. The no of roots on the equation 2s4+s3+3s2+5s+7=0that lie in the right half of s plane is-------(2)
9. For a feedback control system of type 2, the steadystate error for a ramp input is-------(zero)
10. The output of a linear time invariant controlsystem is c(t) for a certain input r(t). if r(t) is modified by passing itthrough a block whose transfer function is e-s and then applied to the system,the modified output of the system would be-----------(c(t-1)u(t-1)
11. The phase lead compensation used to-----(decreasesboth rise time and overshoot)
12. Consider two buses connected by an impedance of(0+j5)ohm. The bus 1 voltage is 100/300 v, and bus 2 voltage is 100/00 v. the real and reactive power supplied by bus 1,resp are……….(1000w, 268 VAr)
13. For a fixed value of complex power flow in atransmission line having a sending end voltage V, the real power loss will beproportional to-----------(1/V2).
14. During a disturbance on a synchronous machine, therotor swings from A to B before finally settling down to a steady state atpoint C on the power angle curve. The speed of the machine during oscillationis synchronous at point(s)--------------------(A and B)
15. A 100 MVA, 11kv, 3 phase 50hz, 8 pole synchronousgenerator has an inertia constant H equal to 4 MJ/MVA. The stored energy in therotor of the generator at synchronous speed will be---(400MJ).
16. In a biased differential relay the bias is definedas a ratio of----------(operating coil current and restraining coil current))
17. Resistance switching is normally employedin------(ABCB)
18. The use of high speed circuit breakers----(improvessystem stability)
19. Keeping in view the cost and overall effectiveness,the following circuit breaker is best suited for capacitor bankswitching---(vacuum)
20. If the reference bus is changed in two load flowruns with the same system data and power obtained for reference bus taken asspecified P and Q in the latter run----------( the system losses will beunchanged but complex bus voltages will change.)
21. The gauss seidel load flow method has followingdisadvantages. Tick the incorrect statement------( unreliable convergence)
22. The torque speed characteristics of a repulsionmotor resembles which of the following dc motorcharacteristic------------(series)
23. Which type of motor is most suitable for computerprinter drive-----(stepper motor)
24. A 4 pole lap wound DC generator has a developedpower of P watts and voltage of E volts. Two adjacent brushes of the machineare removed as they are worn out. If the machine operates with the remainingbrushes, the developed voltage and power that can be obtained from the machineare----(E,P/4)
25. A 4 point starter is used to start and control thespeed of a -----------( dc shunt motor with field weakening control)
26. The function of oil in a transformer is-----( toprovide insulation and cooling)
27. The core flux of a practical transformer with aresistive load------------( is strictly constant with load changes)
28. In a transformer zero voltage regulation at fullload is----(possible at leading pf load)
29. A single phase transformer has a turns ratio of1:2, and is connected to a purely resistive load. The magnetizing current drawnis 1 A, and the secondary current is 1A. if core losses and leakage reactanceare neglected, the primary current is-(2.24A)
30. The low voltage winding of a 400/230V, single phase50hz transformer is to be connected to a 25hz, the supply voltage shouldbe-------(115V)
31. A 400/100V, 10 KVA two winding transformer isreconnected as an auto transformer is reconnected as an auto transformer acrossa suitable voltage source. The maximum rating of such an arrangement couldbe-----(50KVA)
32. When the supply voltage to an induction motor isreduced by 10%, the maximum torque will decrease by approximately-------(20%)
33. In case of a split phase motor, the phase shiftbetween currents in the two windings is around------(300)
34. Starting torque can be obtained in the case of asingle phase induction motor with identical main and auxiliary windings byconnecting-----( a capacitor in series with the auxiliary winding)
35. For a single phase capacitor start induction motorwhich of the following statements is valid---( the direction of rotation can bechanged by reversing the main winding terminals)
36. An induction motor having full load torque of 60zNmwhen delta connected develops a starting torque of 120Nm. For the same supplyvoltage, if the motor is changed to star-connection, the starting torquedeveloped will be-------(40NM)
37. During hunting of synchronous motor –(damper bardevelops torque)
38. The phase sequence of a three phase alternator willreverse if -------(the field current remains the same but the direction ofrotation is reversed)
39. The effect of stray magnetic fields on theactuating torque of a portable instrument is max when the operating filed ofthe instrument and the stray fields are-(parallel)
40. A current of -8+6
(sinwt+300)A is passed through threemeters. They are a center zero PMMC meter, true rms meter and MI instrument.The respective reading( in A) will be----(-8,10,10)
41. R1 and R2 are the opposite arms of a wheatstonebridge as are R3 and R, the source voltage is applied across R1 and R3 underbalanced conditions which one of the following is true---(R1=R2R3/R4)
42. A dc potentiometer is designed to measure up toabout 2v with a slide wire of 800mm. a standard cell of emf 1.18v obtainsbalance at 6010mm. a test cell is seen to obtain balance at 680mm. the emf ofthe test cell is-(1.34v)
43. The minimum number of wattmeters required tomeasure3 phase 3 wire or unbalanced power is—(2)
44. A reading of 120 is obtained when a standardinductor was connected in the circuit of a Q meter and the variable capacitoris adjusted to a value of 300pF. A lossless capacitor of unknown value C, isthen connected and the same reading was obtained when the variable capacitor isreadjusted to a value of 200pF. The value of Cx in pF is—(100)
45. The two inputs of a CRO are fed with the twostationary periodic signals. In the X Y mode, the screen shows a figure whichchanges from ellipse to circle and back to ellipse with its major axis changingorientation slowly and repeatedly. The following inference can be made fromthis----------(there is a constant but small phase difference between thesignals)
46. SCR can be turned off—( anode current should beless than holding current)
47. The no. of pn junctions in SCR-----(3)
48. TRIAC is a—(antiparallel thyristors combination)
49. GTO can be turned off-(by using a negative currentpulse)
50. Which type of control is used for controlling theac drive by using thyristors--------(integral cycle)
51. In DC choppers the output voltage can be controlledby using FM technique varying--------( T , Toff constant)
52. In phase control rectifiers the output voltage
ripple can be controlled by—‘(load inductance)
53. Which is not a current controlleddevice-----(MOSFET)
54. Inverter function---------(DC to AC with variablefrequency)
55. In phase controlled rectifires free wheeling diodemakes-(load current continuation)
56. Dielectric heating application----(wood)
57. In induction heating the following is abnormallyhigh--------(frequency)
initial current through it being zero. The current through the inductor fort>=0 is given by-----------(4t3)
2. Two incandescent light bulbs fo 40w and 60w ratingare connected in series across the mains. Then--------(the 40 bulb glows brighter)
3. Given two coupled inductors L1 and L2, their mutualinductances M satisfies-----(M
4. Consider the star network. The resistance betweenterminals A and B with C open 6ohms, between terminals B and C with A open is11ohms, and between terminals C and A with B open is 9ohms. Then------------(Ra=2, Rb=4, Rc=7)
5. In a series RLC circuit at resonance, the magnitudeof the voltage developed across the capacitor------( can be greater than theinput voltage, however, it is 900 out of phase with the input voltage)
6. A two port device is defined by the following pairof quations:
i1=2v1+v2 and i2=v1+v2 its impedance parameters(z11, z12, z21, z22) are-----(1,-1,-1,2)
7. The impulse response of an initially relaxed linearsystem is e-2tu(t).to produce a response of
te-2tu(t), the input must be equalto--------(e-2t u(t))
8. The no of roots on the equation 2s4+s3+3s2+5s+7=0that lie in the right half of s plane is-------(2)
9. For a feedback control system of type 2, the steadystate error for a ramp input is-------(zero)
10. The output of a linear time invariant controlsystem is c(t) for a certain input r(t). if r(t) is modified by passing itthrough a block whose transfer function is e-s and then applied to the system,the modified output of the system would be-----------(c(t-1)u(t-1)
11. The phase lead compensation used to-----(decreases
both rise time and overshoot)
12. Consider two buses connected by an impedance of(0+j5)ohm. The bus 1 voltage is 100/300 v, and bus 2 voltage is 100/00 v. the real and reactive power supplied by bus 1,resp are……….(1000w, 268 VAr)
13. For a fixed value of complex power flow in atransmission line having a sending end voltage V, the real power loss will beproportional to-----------(1/V2).
14. During a disturbance on a synchronous machine, therotor swings from A to B before finally settling down to a steady state atpoint C on the power angle curve. The speed of the machine during oscillationis synchronous at point(s)--------------------(A and B)
15. A 100 MVA, 11kv, 3 phase 50hz, 8 pole synchronousgenerator has an inertia constant H equal to 4 MJ/MVA. The stored energy in therotor of the generator at synchronous speed will be---(400MJ).
16. In a biased differential relay the bias is definedas a ratio of----------(operating coil current and restraining coil current))
17. Resistance switching is normally employedin------(ABCB)
18. The use of high speed circuit breakers----(improvessystem stability)
19. Keeping in view the cost and overall effectiveness,the following circuit breaker is best suited for capacitor bankswitching---(vacuum)
20. If the reference bus is changed in two load flowruns with the same system data and power obtained for reference bus taken asspecified P and Q in the latter run----------( the system losses will beunchanged but complex bus voltages will change.)
21. The gauss seidel load flow method has followingdisadvantages. Tick the incorrect statement------( unreliable convergence)
22. The torque speed characteristics of a repulsion
motor resembles which of the following dc motorcharacteristic------------(series)
23. Which type of motor is most suitable for computerprinter drive-----(stepper motor)
24. A 4 pole lap wound DC generator has a developedpower of P watts and voltage of E volts. Two adjacent brushes of the machineare removed as they are worn out. If the machine operates with the remainingbrushes, the developed voltage and power that can be obtained from the machineare----(E,P/4)
25. A 4 point starter is used to start and control thespeed of a -----------( dc shunt motor with field weakening control)
26. The function of oil in a transformer is-----( toprovide insulation and cooling)
27. The core flux of a practical transformer with aresistive load------------( is strictly constant with load changes)
28. In a transformer zero voltage regulation at fullload is----(possible at leading pf load)
29. A single phase transformer has a turns ratio of1:2, and is connected to a purely resistive load. The magnetizing current drawnis 1 A, and the secondary current is 1A. if core losses and leakage reactanceare neglected, the primary current is-(2.24A)
30. The low voltage winding of a 400/230V, single phase50hz transformer is to be connected to a 25hz, the supply voltage shouldbe-------(115V)
31. A 400/100V, 10 KVA two winding transformer isreconnected as an auto transformer is reconnected as an auto transformer acrossa suitable voltage source. The maximum rating of such an arrangement couldbe-----(50KVA)
32. When the supply voltage to an induction motor is
reduced by 10%, the maximum torque will decrease by approximately-------(20%)
33. In case of a split phase motor, the phase shiftbetween currents in the two windings is around------(300)
34. Starting torque can be obtained in the case of asingle phase induction motor with identical main and auxiliary windings byconnecting-----( a capacitor in series with the auxiliary winding)
35. For a single phase capacitor start induction motorwhich of the following statements is valid---( the direction of rotation can bechanged by reversing the main winding terminals)
36. An induction motor having full load torque of 60zNmwhen delta connected develops a starting torque of 120Nm. For the same supplyvoltage, if the motor is changed to star-connection, the starting torquedeveloped will be-------(40NM)
37. During hunting of synchronous motor –(damper bardevelops torque)
38. The phase sequence of a three phase alternator willreverse if -------(the field current remains the same but the direction ofrotation is reversed)
39. The effect of stray magnetic fields on theactuating torque of a portable instrument is max when the operating filed ofthe instrument and the stray fields are-(parallel)
40. A current of -8+6
(sinwt+300)A is passed through threemeters. They are a center zero PMMC meter, true rms meter and MI instrument.The respective reading( in A) will be----(-8,10,10)
41. R1 and R2 are the opposite arms of a wheatstonebridge as are R3 and R, the source voltage is applied across R1 and R3 underbalanced conditions which one of the following is true---(R1=R2R3/R4)
42. A dc potentiometer is designed to measure up toabout 2v with a slide wire of 800mm. a standard cell of emf 1.18v obtains
balance at 6010mm. a test cell is seen to obtain balance at 680mm. the emf ofthe test cell is-(1.34v)
43. The minimum number of wattmeters required tomeasure3 phase 3 wire or unbalanced power is—(2)
44. A reading of 120 is obtained when a standardinductor was connected in the circuit of a Q meter and the variable capacitoris adjusted to a value of 300pF. A lossless capacitor of unknown value C, isthen connected and the same reading was obtained when the variable capacitor isreadjusted to a value of 200pF. The value of Cx in pF is—(100)
45. The two inputs of a CRO are fed with the twostationary periodic signals. In the X Y mode, the screen shows a figure whichchanges from ellipse to circle and back to ellipse with its major axis changingorientation slowly and repeatedly. The following inference can be made fromthis----------(there is a constant but small phase difference between thesignals)
46. SCR can be turned off—( anode current should beless than holding current)
47. The no. of pn junctions in SCR-----(3)
48. TRIAC is a—(antiparallel thyristors combination)
49. GTO can be turned off-(by using a negative currentpulse)
50. Which type of control is used for controlling theac drive by using thyristors--------(integral cycle)
51. In DC choppers the output voltage can be controlledby using FM technique varying--------( T , Toff constant)
52. In phase control rectifiers the output voltageripple can be controlled by—‘(load inductance)
53. Which is not a current controlleddevice-----(MOSFET)
54. Inverter function---------(DC to AC with variablefrequency)
55. In phase controlled rectifires free wheeling diodemakes-(load current continuation)
56. Dielectric heating application----(wood)
57. In induction heating the following is abnormallyhigh--------(frequency)
1. The speed torque characteristics of a series motor is a/an--------------(Hyperbola)
2. In ad dc generator, if the variable loss is equal to constant loss, then efficiency is-------(Max)3. The armature of a dc machine is laminated to reduce-----(eddy current loss)4. The initial flux in a dc generator is provided by-----(residual magnetism)5. For the operation of milling machine, which motor is used----( DC shunt motor)6. In a series motor, the torque is----( proportional to square of armature current)7. By conducting swinburn’s test on a dc machine, the following losses can be determined-----( constant losses)8. The series motors have relatively----( High starting torque)9. In a dc shunt motor, the torque developed is 15Nm at 10A of load current. If the load current is doubled, the new torque will be----(30Nm).10. The internal characteristics of s dc shunt generator is a plot between----(Eg and Ia)11. The back emf of motor at the time starting is -----------(zero)12. At low flux densities, the flux in a dc generator varies----(Linearly with field current)13. Three resistances of R ohms each are connected in delta. Its equivalent resistances in star connection per phase is -----(R/3 each)14. The RMS value of a triangular wave of alternating quantity having peak value 3A is -----(sqrt 3)15. In as series RL circuit, the voltage across the resistance is 40V and voltage across inductance is 40v. Then the total voltage across the series circuit--------(56.56V)16. A transformer can have regulation closer to zero---( on leading pf)17. The full load copper loss of a transformer is 1600watts. At half load, the copper loss----(400watts)18. A 440/110, 1- phase transformer has a primary resistance of 0.03ohms and secondary resistance of 0.02ohms. its iron losses at normal input are 150 watts. The secondary current at which the maximum efficiency will occur is -------(82.80A)19. Which of the following transformers should never have the secondary open circuited while primary is energized---------(CT)20. An isolation transformer has primary to secondary turn’s ratio of-------(1:1)
21. In a 50 KVA, 1-phase transformer, the iron loss is 500W and full load copper loss is 800W. The efficiency of the transformer at full load at 0.8 pf lagging is----(96.85%)22. A synchronous motor can be used as a synchronous capacitor when it is---(over excited)23. The harmonic component of the generated emf will be more in alternators with-------(Full pitch coils)24. V-curves for a synchronous motor represent the relation between---(Ia and If)25. The crawling in an induction motor is caused by-----(harmonics developed in the motor)26. The ratio of starting torque to normal torque in case of a star delta starter will be---(1/3)27. A 3-phase, 440v, 50hz induction motor has 4% slip. The frequency of rotor emf will be----(2Hz)28. In a tuned line-----------( receiving end voltage and current are numerically equal to corresponding sending end values)29. The max torque in an induction motor depends on------(frequency)30. which of the following motors will have relatively high power factor---(capacitor run motor)31. which of the following motors can be used for unity pf---(Schrage motor)32. which of the following turbines will be used for heads from 500m to 200m--------(Francis)33. The sudden change of pressure in penstock pipes due to sudden reaction of load is avoided using-------(surge tank)34. Which of the following heat exchangers is used to raise the temperature of steam from normal to super saturation level------(superheater)35. which of the following treatments for water is used to remove non carbonate hardness-----(Soda treatment)36. The hoppers in electrostatic precipitator are generally----------in shape(pyramidal)37. The purpose of cooling tower is---( to cool the steam in the condenser)38. which is used to reduce the speed of the neutrons in a nuclear reactor-----(moderator)39. which of the following is a cladding material in nuclear reactor---(Magnesium)40. In which of the following reactors, reactor control is achieved by varying moderator level ----------(CANDU)
41. A generating station has a connected load of 450MW and a maximum demand of 250MW. The units generated are 615*10^6 per annum. The load factor of the station is -----(0.281)42. The plant capacity is determined by-------(Plant use factor)43. A power plant has a maximum demand of 15MW. The load factor is 50% and the plant factor is 40%. The operating reserve is ----(3.75MW)44. A transformer is rated at 66Kv/4001V, 1000KVA, 5% reactance. The short circuit MVA of the transformer when connected to infinite bus is-----(20MVA)45. The power frequency rms voltage, that appears across the breaker contacts after the transient oscillations die out and final extinction of arc that results in all the poles is called-------(recovery voltage)46. In resistance switching, the function of shunt resistor----------(reduces the rate of rise of restriking voltage)47. The no. of poles per phase of breaker is a function of------(Operating voltage)48. The capacitor switching is easily done with------(vacuum CB)49. A distance relay is inherently directional if its characteristics on R-X diagram is------( a circle that passes through origin)50. The most efficient torque producing actuating structure in an induction relay is ---------(induction cup structure)51. The line trap unit employed in carrier current relaying----(offers high impedance to carrier frequency signals)52. The protection relay used for low fault settings and high operating speeds in a transformer is -----------(Harmonic restraint relay)53. The wattmetric relay with directional characteristic is used for protection of generator against------(failure of prime mover)54. The best suited relay for 3- zone protection scheme is ----(Mho relay)55. The rule 77 of Indian electricity rules(1956) for over head lines gives information about----(clearance above ground of lowest conductor)56. The stringing charts are used to calculate-----(Tension and sag at any temperature)57. Due to proximity effect, the effective internal reactance of the conductor---(decrease)58. The inductance of a single phase two wire transmission line per kilometer gets doubled when the----------------(distance between the wires is increased as square of the original distance)
59. a transmission line of 210km length has certain values for A,B,C and D parameters. If the length of line is made 100km then------(A increases and B decreases)60. The surge impedance loading of the line is proportional to—(V^2)61. Under no load conditions the current in a transmission line is due to------( capacitance of the line)62. For a transmission line, the no load receiving end voltage is more than the sending end voltage. This is called---------(Ferranti effect)63. Corona loss can be reduced by the use of hollow conductor, because-----( for a given cross section, the radius of the conductor is increased)64. The non shielding method of over voltage protection is based on the principle of --------(insulation breakdown)65. The valve elements of non linear resistance in valve type lighting arrester are made up of -----------(silicon carbide)66. Which of the following lightning arresters, can discharge currents, between 65000 to 100000A-------(line type)67. Which of the following is used to reduce tower footing resistance-------(ground rods)68. In substations, the breaker maintenance facility is provided in the----(main and transfer bus scheme)69. In case of rigid bus arrangement, the size of aluminum pipe used for voltage level of 66KV----------------(65mm)70. For low voltage applications up to 11KV, which of the following insulators is preferred-------(pin type)71. In a 5 insulator disc, string capacitance between each unit and earth is 1/6 th of the mutual capacitance. The voltage distribution across the middle unit as % of voltage applied is------(17.1)72. An electric train taking of constant current of 600A moves on a section of line between two substations 8km apart maintained at 575V and 590V resp. The track resistance is 0.04ohm per km both go and return. The point minimum potential along the track is at a distance from 575V substation is----(3.67Km)73. which of the following is the most economical ac distribution system------( ac 3 phase 3 wire)74. for a distributor design, if the voltage rating is increased by ‘n’ times, the conductor size reduces to ----of the original(1/n2)
75. The pointer of an indicating instrument is generally made of ------------(aluminum)76. Electrostatic instruments are used as-------------only(voltmeters)77. In a dynamometer wattmeter, the moving coil is the----(potential coil)78. A 50V range voltmeter has a sensitivity of 20 k-ohms/volt. The total resistance of the voltmeter is -----(1MOHM)79. An RLC series resonant circuit has a Q of 15 and a source voltage of 50V. the voltage across the capacitor at resonance is -----(750V)80. At parallel resonance conditions the power factor is--------(unity)81. In AC circuit, V and I are given by: V=100sin(100t) V and I=100sin(100t+∏/3)mA. The power dissipated in the circuit is------(2.5W)82. In the measurement of 3-phase power by two wattmeter method, the two wattmeter’s indicate equal readings if the power factor is----(unity)83. In a parallel RLC circuit, below resonance frequency, the circuit behaves as----(inductive)84. In a balanced 3-phase star connected system, the phase difference between line and phase voltages is—(30deg)85. The electric heater draws 10A from a 230V line. The resistance of the heater is---(23ohm)86. A wire has a resistance of 12ohms. It is bent in the form of an equilateral triangle. The effective resistance between any two corners of the triangle is---(8/3ohms)87. ACSR stands for----------( Aluminum Conductor Steel Reinforced)88. In house wiring, the total connected load per sub circuit can be---(800W)89. Which of the following motors is used for intermittent high torque load and for rolling mills-----(DC cumulative compound wound motor)90. In plugging of dc motors---------(connections to armature are reversed)91. The motor enclosure used in wood working industry is---(totally enclosed fan cooled type)92. The unit of luminous flux is---(lumens)93. The illumination at a surface due to a source of light placed at a distance ‘d’ from the surface varies is ---(1/d^2)94. Reduction factor is the ration of-----(MSCP/MHSCP)95. Power factor is the highest in case of -----(incandescent lamp)96. In carbon arc welding---(Electrode is positive with respect to work in case of dc supply)
97. Rolling electrodes are specifically used for---( seam welding)98. In resistance furnace, the atmosphere is----------(oxidizing)99. Which of the following motors can be used for unity power factor---------(Schrage motor)100. The least expensive drive is------(belt drive)