TRAMEC HEAVY DUTY AIR BRAKE HOSE ASSEMBLIES TRAMEC HEAVY DUTY AIR BRAKE HOSE ASSEMBLIES Meets DOT 106 & SAE J1402 Both Ends Swivel After Installation Factory.

TRAMECHEAVY DUTY AIR BRAKE

HOSE ASSEMBLIES

TRAMECHEAVY DUTY AIR BRAKE

HOSE ASSEMBLIES

• Meets DOT 106 & SAE J1402

• Both Ends Swivel After Installation

• Factory or Field Assembly

• Non-Corrodable Parts in the Air Path

• Meets DOT 106 & SAE J1402

• Both Ends Swivel After Installation

• Factory or Field Assembly

• Non-Corrodable Parts in the Air Path

ConstructionConstructionReinforced Nylon Tube Supports HoseReinforced Nylon Tube Supports Hose

O-Ring Seals Air & Allows Swivel (-60°F)O-Ring Seals Air & Allows Swivel (-60°F)

Brass Fitting Provides “Live Swivel” Fitting Is Retained By Tube & ShellBrass Fitting Provides “Live Swivel” Fitting Is Retained By Tube & Shell

Reinforced Nylon Shell Provides Consistent Compression of Hose to Seal on the TubeReinforced Nylon Shell Provides Consistent Compression of Hose to Seal on the Tube

Plated Steel Ring Defines Outside Diameter Plated Steel Ring Defines Outside Diameter

Standard SAE J1402 Air Brake HoseStandard SAE J1402 Air Brake Hose

ConventionalCrimped StyleConventionalCrimped Style

TRAMEC “Live Swivel” FittingTRAMEC “Live Swivel” Fitting

Eliminates Swivel Adapters Both Ends Swivel Eases Installation

Eliminates Swivel Adapters Both Ends Swivel Eases Installation

Reduces Stress on Hose Material Extends Hose LifeReduces Stress on Hose Material Extends Hose Life

Assembly ConfidenceAssembly Confidence

Molded Shell & Tube Define Squeeze Hose Compression Not Subject to Operator Set Up

Molded Shell & Tube Define Squeeze Hose Compression Not Subject to Operator Set Up

ConventionalCrimped StyleConventionalCrimped Style

Molded Shell & Ring Design Allows Visual Inspection of Hose Insertion Depth

Molded Shell & Ring Design Allows Visual Inspection of Hose Insertion Depth

Assembly ConfidenceAssembly Confidence

Fitting StyleFitting Style

14.914.5

19.314.5

14.914.5

19.314.5

Average Impact HtAt Failure

Average Impact HtAt Failure

3/8” Live Swivel3/8” Crimped

1/2” Live Swivel1/2” Crimped

3/8” Live Swivel3/8” Crimped

1/2” Live Swivel1/2” Crimped

In addition to exceeding all DOT & SAE requirements for tensile, burst, flexural, temperature, etc. The TRAMEC live swivel has demonstrated that it is as least as strong as the conventional fitting in resisting side impact (no DOT requirement).

In addition to exceeding all DOT & SAE requirements for tensile, burst, flexural, temperature, etc. The TRAMEC live swivel has demonstrated that it is as least as strong as the conventional fitting in resisting side impact (no DOT requirement).

Repeated impacts by a weight dropped from increasing heights, while at 150 psi.

Repeated impacts by a weight dropped from increasing heights, while at 150 psi.

TRAMEC “Live Swivel” FittingTRAMEC “Live Swivel” Fitting

Available for3/8” I.D. ...Available for3/8” I.D. ...

And for 1/2” I.D.Air Brake HosesAnd for 1/2” I.D.Air Brake Hoses

TRAMEC “Live Swivel” FittingTRAMEC “Live Swivel” Fitting

In Kits for3/8” I.D. Hose

In Kits for3/8” I.D. Hose

… or Bulk Packed for3/8” & 1/2” I.D. Hose… or Bulk Packed for3/8” & 1/2” I.D. Hose

Assembly MethodsAssembly Methods

By Hand UsingA Hex Key

orWith A Powered

Screw Driver( 3/8 Hose )

By Hand UsingA Hex Key

orWith A Powered

Screw Driver( 3/8 Hose )

HA300Bench Fixture

HA300Bench Fixture

HA100MachineHA100

Machine